Happymodel BNF Mobula6 HDZero V3 1S 65mm Whoop - ELRS 2.4GHz

  • VendorRaceDayQuads

Description

The Happymodel Mobula 6 HDZero 1S Whoop is the very first 65mm HD brushless whoop in the world, weighing less than 23.5 grams! The Mobula6 is a smooth and agile brushless drone that comes with the HDZero Nano Lite Camera, EX0802 KV19000 Motors, and many other cool features and specs that make this whoop a must-have! Happymodel has teamed up with HDZero, Runcam, Nick Burns, Mr. Shutterbug, Ryan Quellet, and many other enthusiasts to here to make the dream come true! This whoop comes with Built-In ELRS V3!

Note: Batteries are not included.

UART ELRS V3.0 ready
Battery Plug: GNB A30
Onboard black box ready

Default factory dump file:

dump file for Mobula6 HDZERO 1S 65mm digital HD brushless whoop V3

Specifications

Flight controller SuperX HD ELRS

  • Betaflight 4.4.2 firmware ready
  • Firmware target: CRAZYBEEF4DX
  • MCU:STM32F411CEU6 (100MHz, 512K FLASH)
  • Sensor: BMI270 or ICM42688P (SPI connection)
  • Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone
  • Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read
  • Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update
  • Bluejay ESC Firmware ready
  • Built-in 5V 1A BEC
  • Built-in voltage detection
  • No betaflight analog osd chip

Onboard 4in1 ESC

  • Power supply: 1-2S LiPo/LiPo HV
  • Current: 12A continuous peak 15A (3 seconds)
  • Support ESC-Configurator and BLHELI_S Suite configurator
  • Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz
  • Default protocol: DSHOT300

Onboard UART ExpressLRS 2.4GHz Receiver

  • RF Frequency: 2.4GHz
  • Antenna: enameled copper wire 31mm length
  • Telemetry output Power: <12dBm
  • Receiver protocol: CRSF
  • Default firmware version: ExpressLRS V3.0.1
  • The same hardware with Happymodel EP1 receiver
  • Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through

Motor

  • Mode: EX0802 19000KV
  • Configu-ration:9N12P
  • Stator Diamter:8mm
  • Stator Length:2mm
  • Shaft Diameter:Φ1mm
  • Motor Dimension(Dia.xLen):Φ10.5mmx14.9mm
  • Weight(g):1.7g
  • No.of Cells(Lipo):1S only

Propeller Gemfan 1219 Bi-blades

  • Weight:0.19g
  • Material: PC
  • Pitch:1 inchProps Dia:30mm
  • Center Hole Dia:1mm

HDZero Nano Lite Camera

  • 14x16x11 mm
  • 1.5gram
  • 0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMos sensor
  • Excellent low light performance
  • Fov:
  • 4:3: D:130° H:108° v:84°
  • 16:9:D:122° H:108° V:65°

HDZero Whoop Lite VTX

  • 1S Input
  • 25mW/200mW RF Output-SmartAudio Support
  • 25.5×25.5 M2 Soft Mounting- Antenna Retention
  • Removable Shielding Box- 32.5×32.5mm(29x29mm inner)
  • 4.5grams/4mm Thickness (without shielding)

      Links

      Includes

      • 1x Happymodel Mobula6 HDZero 1S Whoop
      • 1x Gemfan 1210 31mm Propeller (Set of 4)
      • 1x Propeller disassemble tool
      • 1x Spare Canopy
      • 1x Screwdriver
      Product form

      $195.99

        SKU: sku-39872791674993

        Brand: RaceDayQuads | Quad

        Product Tags

        Description

        The Happymodel Mobula 6 HDZero 1S Whoop is the very first 65mm HD brushless whoop in the world, weighing less than 23.5 grams! The Mobula6 is a smooth and agile brushless drone that comes with the HDZero Nano Lite Camera, EX0802 KV19000 Motors, and many other cool features and specs that make this whoop a must-have! Happymodel has teamed up with HDZero, Runcam, Nick Burns, Mr. Shutterbug, Ryan Quellet, and many other enthusiasts to here to make the dream come true! This whoop comes with Built-In ELRS V3!

        Note: Batteries are not included.

        UART ELRS V3.0 ready
        Battery Plug: GNB A30
        Onboard black box ready

        Default factory dump file:

        dump file for Mobula6 HDZERO 1S 65mm digital HD brushless whoop V3

        Specifications

        Flight controller SuperX HD ELRS

        • Betaflight 4.4.2 firmware ready
        • Firmware target: CRAZYBEEF4DX
        • MCU:STM32F411CEU6 (100MHz, 512K FLASH)
        • Sensor: BMI270 or ICM42688P (SPI connection)
        • Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone
        • Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read
        • Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update
        • Bluejay ESC Firmware ready
        • Built-in 5V 1A BEC
        • Built-in voltage detection
        • No betaflight analog osd chip

        Onboard 4in1 ESC

        • Power supply: 1-2S LiPo/LiPo HV
        • Current: 12A continuous peak 15A (3 seconds)
        • Support ESC-Configurator and BLHELI_S Suite configurator
        • Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz
        • Default protocol: DSHOT300

        Onboard UART ExpressLRS 2.4GHz Receiver

        • RF Frequency: 2.4GHz
        • Antenna: enameled copper wire 31mm length
        • Telemetry output Power: <12dBm
        • Receiver protocol: CRSF
        • Default firmware version: ExpressLRS V3.0.1
        • The same hardware with Happymodel EP1 receiver
        • Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through

        Motor

        • Mode: EX0802 19000KV
        • Configu-ration:9N12P
        • Stator Diamter:8mm
        • Stator Length:2mm
        • Shaft Diameter:Φ1mm
        • Motor Dimension(Dia.xLen):Φ10.5mmx14.9mm
        • Weight(g):1.7g
        • No.of Cells(Lipo):1S only

        Propeller Gemfan 1219 Bi-blades

        • Weight:0.19g
        • Material: PC
        • Pitch:1 inchProps Dia:30mm
        • Center Hole Dia:1mm

        HDZero Nano Lite Camera

        • 14x16x11 mm
        • 1.5gram
        • 0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMos sensor
        • Excellent low light performance
        • Fov:
        • 4:3: D:130° H:108° v:84°
        • 16:9:D:122° H:108° V:65°

        HDZero Whoop Lite VTX

        • 1S Input
        • 25mW/200mW RF Output-SmartAudio Support
        • 25.5×25.5 M2 Soft Mounting- Antenna Retention
        • Removable Shielding Box- 32.5×32.5mm(29x29mm inner)
        • 4.5grams/4mm Thickness (without shielding)

            Links

            Includes

            • 1x Happymodel Mobula6 HDZero 1S Whoop
            • 1x Gemfan 1210 31mm Propeller (Set of 4)
            • 1x Propeller disassemble tool
            • 1x Spare Canopy
            • 1x Screwdriver

            Recently Viewed...

            © 2024 Caloosa Trains And Hobbies,

              • Amazon
              • American Express
              • Apple Pay
              • Discover
              • Google Pay
              • Mastercard
              • PayPal
              • Shop Pay
              • Venmo
              • Visa

              Login

              Forgot your password?

              Don't have an account yet?
              Create account