Electronic Speed Control

99 products


  • TRA3355R, Traxxas VXL-3S Brushless ESC (Waterproof) TRA3355R, Traxxas VXL-3S Brushless ESC (Waterproof)

    Traxxas TRA3355R, Traxxas VXL-3S Brushless ESC (Waterproof)

    Out of stock

    TRA3355R, Traxxas VXL-3S Brushless ESC (Waterproof) This is the Traxxas VXL-3S Brushless Electronic Speed Control. This Speed Control simplifies brushless technology with easy, built-in profiles and intuitive programming. Tri-mode operation auto detects the motor type for brushed, sensored, or sensorless brushless motors. The VXL-3s uses advanced circuit design that allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. It sets up, operates, and programs just like the Traxxas XL-5 family of ESCs so there's no tricky new procedures to learn. Traxxas exclusive patented Training Mode is also included to limit full throttle to 50% for young or inexperienced drivers. For the most advanced users, the VXL-3s is equipped with two-stage low voltage detection to allow LiPo battery use. The VXL-3s is manufactured by Traxxas to ensure the highest level of quality and support and is backed by the Traxxas Lifetime Electronics Warranty. Features: The VXL-3s auto-detects the motor type for brushless and sensored brushless motors. Patented Traxxas High-Current Connector eliminates a common bottleneck and maintains pure, unrestricted power flow from the battery to the brushless power system. Built-in two-stage low voltage detection for Lithium Polymer (LiPo) battery use provides a clear signal to the driver that the battery pack is nearing its minimum voltage threshold. Widest range of battery options ranging from 4-cell NiMH or NiCad packs all the way up to 3S LiPo battery packs (11.1 volt) The patented Training Mode™ is an exclusive Traxxas feature that reduces the overall power output of the VXL-3s by 50%, making it easier for new or younger drivers to control their model. When they're ready, simply change profiles to unleash full-throttle action. Advanced circuit design allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. There's no need for additional sensor wiring and hardware complexity. The EZ-Set® push-button setup operates and programs just like other Traxxas speed controls such as the XL-5. This eliminates the need to learn a new set of procedures. The VXL-3s is programmable with three drive profiles: Sport Mode – Fwd / Brake / Rev Race Mode – Fwd / Brake Training Mode**™ – 50% Fwd / Brake / 50% Rev More Features: Multi-color LED provides clear feedback Since the VXL-3s allows experimentation with many kinds of motors, it is equipped with numerous failsafe features to help protect against common mishaps that can cause other systems to fail. Two-stage thermal shutdown protection protects the VXL-3s from overheating. Locked Rotor Protection™ prevents system damage by cutting power if the vehicle is stuck or the motor is bound. Sensor Phase Detection™ protects against improperly wiring aftermarket sensored motors. Sensored Motor Backup protection causes the VXL-3s to switch to sensorless operation if a motor sensor fails or sensor wires become disconnected. Sensored motors can be used without connecting the sensor wires to the sensor port on the ESC. Battery Over-Voltage Protection™ causes the ESC to go into failsafe mode if the maximum input voltage is exceeded. Water resistant case design uses rubber seals and o-rings to protect against damage caused by water and moisture. Micro-fin aluminum heatsink dissipates heat. The built-in auxiliary fan output powers a snap-on accessory fan for increased cooling capacity during extreme use. A handy clasp on the speed control case keeps the wire neatly in place until you are ready to use it. MOSFET design provides high-current output (320 amp peak) with incredibly low resistance (.00075 (ohm)). Gold plated 3.5mm bullet connectors on 12-gauge Maxx® Cable flow full power to the motor without performance strangling resistance. Specifications: Input Voltage: NiCad/NiMH 4-9 Cells (4.8 to 10.8 Volts DC); LiPo 2-3 Cells: (7.4 to 11.1 Volts DC) Case Size: 39mmW x 55mmD x 33mmH Weight: 90 grams Motor Limit (Brushed/Brushless): No motor limit On Resistance Forward: 0.00075 Ohms On Resistance Reverse: 0.00075 Ohms Peak Current - Forward: 320A Peak Current - Reverse: 320A Braking Current: 320A Continuous Current: 200A BEC Voltage: 6.0 V BEC Current: 2.5A (with 6-cell NiMH) Power Wire: 12-Gauge Maxx® Cable Input Harness Wire: 26 Gauge / 100mm Transistor Type: MOSFET Low Voltage Detection: 2-Stage indicators, switchable (on or off) Thermal Protection: 2-Stage thermal shutdown Single-Button Setup: Yes, Traxxas EZ-Set® Battery Input Connector : Traxxas High-Current Connector Motor Types (Autodetect): Brushed, brushless, sensored brushless Ports: RX Input, motor sensor, auxiliary fan Documents and Resources for TRA3355R Traxxas VXL-3S Waterproof ESC Manual This product was added to our catalog on April 12, 2021

    Out of stock

    $99.99

  • CSE011-0135-00, Castle Creations B Link Bluetooth Adapter CSE011-0135-00, Castle Creations B Link Bluetooth Adapter

    Castle Creations CSE011-0135-00, Castle Creations B Link Bluetooth Adapter

    Out of stock

    CSE011-0135-00, Castle Creations B Link Bluetooth Adapter The Castle Creations B Link Bluetooth Adapter gives you access to powerful Castle Link ESC tuning features right from your iOS or Android smartphone! Castle Link is an essential component of customization for all Castle ESCs. While the controllers are plug and play, the benefits of fine tuning your Castle ESC through the Castle Link Programming Suite have only reinforced the sophistication and value of the Castle product line. Not only do you get the ability to adjust many variables to enhance your experience, you have the assurance that firmware updates for future features and improvements for your controller are provided at no cost to you.  Discover just how easily and quickly you can reign in tuning with the release of the Castle B•LINK BLUETOOTH ADAPTER, which will allow most Castle Link compatible products to be programmed via Bluetooth enabled mobile devices using the free application, with firmware updating to be added soon. CASTLE LINK APP FEATURES:The Castle Link App contains all of the same tuning options as the Castle Link USB Programming Suite used on a Windows compatible PC, now with even greater flexibility.  NOTE: All current Castle Creations ESCs, many older units and the BEC 2.0 and BEC Pro are supported, for a complete listing of compatible ESCs and accessories please view the PDF file in the resources tab above. App available for free at the Apple App Store and Google Play.  Features: WIRELESS BLUETOOTH COMMUNICATION allows you to interface with most Castle Link compatible ESCs and accessories to change parameters and update  firmware. DATA LOG VIEWING allows the user to view and download data logs wirelessly, giving you the information needed to fine tune your setup. COMPACT AND LIGHTWEIGHT at 1.20" x .81" x .25" (30.48mm x 20.55mm x 6.55mm) and 0.23oz (6.62g), it can be installed in the vehicle or airframe without significantly increasing model weight. CONVENIENT WATERPROOF DESIGN allows you to quickly adjust settings in the field without disconnecting or disassembling the model. It can stay installed in the model or be easily swapped between models. FREE APP DOWNLOAD is readily available in the Apple App Store or Google Play. Once downloaded it does not require a data connection so it can be used in the most remote of areas and won’t use data. EASY TO USE application can be used with multiple B-Link Bluetooth Adapters or can store model information and allow you to use one adapter on multiple models. PASSCODE PROTECTED with (user-selectable) 4-digit code to prevent unwanted tampering with your settings. SYNC information between multiple devices by creating a free account (requires internet connection to sync database). Specifications: Input Voltage: Minimum: 4.5V - Maximum: 13V Max Continuous Current: 10A Maximum Burst Current: 20A Dimensions (with wires): 7.25" x 0.81" x 0.27" (184.15mm x 20.55mm x 0.27"mm) Dimensions (w/o wires): 1.20" x 0.81" x 0.27" (30.48mm x 20.55mm x 0.27"mm) Weight: 6.62gm / 0.015lbs Needed for Operation: Castle Link App found at Apple Store or Google Play.  This product was added to our catalog on May 1, 2021

    Out of stock

    $56.99

  • CSE011-0119-00, Castle Creations Castle Link V3 USB Programmer Adapter CSE011-0119-00, Castle Creations Castle Link V3 USB Programmer Adapter

    Castle Creations CSE011-0119-00, Castle Creations Castle Link V3 USB Programmer Adapter

    4 in stock

    CSE011-0119-00, Castle Creations Castle Link V3 USB Programmer Adapter The Castle Creations Castle Link contains a proprietary interface adapter and standard USB cable that will give you in depth access to the programmable parameters of your Castle Creations ESC. All you need is an available USB port on your PC. Program your Castle brushless ESCs and accessories on your Windows® PC with the Castle Link USB programming kit. Set up of programmable options with point and click ease View your current program settings Air users can customize values for low-voltage cutoff, prop brake strength, governor gain and more Surface users can customize values for low-voltage cutoff, drag brake, torque limiting and more Download new software updates as they become available Simple programming interface featuring: All-in-one support for all Phoenix, Talon, Thunderbird, QuadPack, DMR, Mamba, Sidewinder, and Hydra controllers, as well as accessories like Telemetry Link, as well as all of our external switching regulators (BECs). Demo Mode allows users to check available settings without connecting their Castle device to the computer Simple to install software Expanded programming and parameters for all Castle ESCs Set-up instructions: Download the interface software. Plug the Castle Link into the receiver lead on your controller and attach the mini USB cable included in the kit. Connect the USB cable to your PC. System Requirements: Castle Link is compatible with Windows Vista, Windows 7, Windows 8 and Windows 10. Note: Macintosh users may take advantage of software such as Parallels Desktop, VMware Fusion, or Apple's Boot Camp along with Windows Vista, Windows 7, Windows 8 and Windows 10. to run the Castle Link software, provided the Macintosh has an Intel processor. Macintosh installation is not supported by Castle Creations. This product was added to our catalog on August 31, 2021

    4 in stock

    $24.99

  • TRA3465, Traxxas Velineon VXL-4S Brushless Electronic Speed Control TRA3465, Traxxas Velineon VXL-4S Brushless Electronic Speed Control

    Traxxas TRA3465, Traxxas Velineon VXL-4S Brushless Electronic Speed Control

    1 in stock

    TRA3465, Traxxas Velineon VXL-4S Brushless Electronic Speed Control Traxxas Velineon VXL-4S Brushless Electronic Speed Control. This ESC is a replacement for the Traxxas Maxx Monster Truck.  Specifications:  Input Voltage: 3S–4S LiPo (11.1V – 16.8V) Case Size: 2.83 inches (72mm) x 2.32 inches (59mm) x 1.93 inches (49mm) Weight: 201g (7.09oz) BEC Voltage: 6.0 V BEC Current Continuous: 10 A BEC Current Peak: 20 A Motor Connectors: Traxxas 6.5mm bullet connectors Battery Connectors: Traxxas High-Current Connectors Power Wire: 10-gauge Maxx Cable Ports: RX input, auxiliary fan, Traxxas accessory port  This product was added to our catalog on May 2, 2021

    1 in stock

    $139.99

  • TRA3018R, Traxxas XL-5 Waterproof ESC w/Low Voltage Detection TRA3018R, Traxxas XL-5 Waterproof ESC w/Low Voltage Detection

    Traxxas TRA3018R, Traxxas XL-5 Waterproof ESC w/Low Voltage Detection

    4 in stock

    TRA3018R, Traxxas XL-5 Waterproof ESC w/Low Voltage Detection This is the Traxxas XL-5 Waterproof ESC. Designed and engineered by Traxxas, the XL-5 Electronic Speed Control handles the elements while smoothly supplying power to the motor. This high-performance ESC is packed with impressive specifications that are normally only found on more expensive high-end replacement units. The XL-5 features a completely waterproof design, three throttle profiles, Thermal Shutdown Protection, 4-8 cell compatibility, and built-in BEC. High frequency operation combined with ultra-low resistance make the XL-5 an efficient and ultra-smooth fully proportional speed control. An exclusive feature on the XL-5 is the patent pending Training Mode™. This profile reduces the overall power output of the XL-5 by 50% making it easier for young or new drivers to develop their control skills before unleashing full-power operation. The XL-5 is manufactured by Traxxas to ensure the highest level of quality and support. The XL-5 is backed by the Traxxas Lifetime Electronics Warranty. Traxxas High-Current Connector: The XL-5 ESC is equipped with the Traxxas high-current connectors for restriction-free current flow. Patent-Pending Training Mode: An exclusive feature that places the XL-5 ahead of the pack is the patent pending Training Mode. This feature reduces the overall power output of the XL-5 by 50% making it easier for new drivers to control their model.  When they’re ready, simply change profiles to unleash full-throttle action.  Only Traxxas has it! XL-5 Waterproof ESC Features: Innovative water sealed design 15-turn motor limit for 540 size motors 12-turn motor limit for 550 size motors Fully-proportional forward, reverse, and braking control Programmable with three drive profiles: Sport Mode – Fwd / Brake / Rev Race Mode – Fwd / Brake Training Mode – 50% Fwd / Brake / 50% Rev EZ-Set® push-button setup Multi-color LED Thermal shutdown protection Efficient, low-loss MOSFET design High-capacity heat sink Smooth, high-frequency operation Easy installation in Traxxas models Backed by the Traxxas Lifetime Electronics warranty XL-5 (WATERSEALED) ESC Specifications: Input voltage: 4-7 Cells NIMH or 2S LiPo Case Size: 1.23"W x 2.18"D x 0.61" H Weight: 2.44 Ounce Motor Limit: 15-turns** (540 Size) 12-turns** (550 Size) On Resistance Forward: 0.007 Ohms On Resistance Reverse: 0.014 Ohms Peak Current - Forward: 100A Peak Current - Reverse: 60A Braking Current: 60A Continuous Current: 14A BEC Voltage: 6.0 VDC BEC Current: 1A Power Wire: 14 Gauge / 5" Input Harness Wire: 26 Gauge / 9" Transistor Type: MOSFET PWM Frequency: 1600 Hz Thermal Protection: Thermal shutdown Profile selection: Sport Mode: 100% FWD, 100% brakes, 100% REV Race Mode: 100% FWD, 100% brakes, no REV Training Mode: 50% FWD, 100% brakes, 50% REV Single-button setup: Yes, Traxxas EZ-Set® **NOTE: When properly geared This product was added to our catalog on September 7, 2021

    4 in stock

    $69.99

  • CSE010016502, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/1717 Sensored Motor (1650kV) CSE010016502, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/1717 Sensored Motor (1650kV)

    Castle Creations CSE010016502, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/1717 Sensored Motor (1650kV)

    1 in stock

    CSE010016502, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/1717 Sensored Motor (1650kV) COMPATIBILITY: Arrma Felony 6S BLX Arrma Infraction 6S BLX Arrma Infraction V2 6S BLX Arrma Limitless Arrma Outcast 8S BLX The Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo with 1717 Sensored Motor is an incredible combo developed specifically for high voltage large scale applications. The MAMBA MONSTER X 8S ESC utilizes Castle’s proprietary CRYO-DRIVE technology helping to reduce the heat generated, and remove heat more efficiently. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 40mm cooling fan and a forged elliptical fin heatsink, the design maximizes airflow throughout the system, taking thermal performance to a level never seen before. Mamba Monster X 8S is a workhorse that will dominate in the harshest of environments. Designed with durability in mind, this ESC features a robust aluminum case, combined with epoxy potting helps to guarantee protection around the circuitry, as well as allowing all-weather use. You can easily optimize the ESC for any driving condition - rugged terrain, smooth pavement, or rock and gravel, the MMX8S can handle it all. Plus, the Castle Link Programming Suite will allow the user to create, save and download setup profiles using a Windows™ PC, or wirelessly with the convenience of the B-Link™ Bluetooth™ Adapter and Castle Link app for Android or iOS. The MMX8S also allows tuning on-the-fly via the Auxiliary wire, allowing access to programming parameters such as Torque Control, Max Brake or Rock Race Mode, further optimizing your vehicle for any racing or bashing application you can imagine! When paired with the included Castle 1717-1650KV sensored motor, heavy, high speed rigs will experience controllable low-end control without sacrificing power, punch or speed. This motor is a blast from the past with the added benefit of sensored capabilities! It is the perfect upgrade for any 1/6th scale vehicles weighing up to 20 lbs and running up to 8s LiPo; it is also a great upgrade for drivers looking for a reliable, high torque 8s motor for their 1/8th scale vehicles! The Castle 1717 1650KV sensored motor features an improved 4-POLE 12-SLOT design that boasts exceptional EFFICIENCY and produces LESS HEAT. SmartSense™ mode uses the motor’s sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is spinning, it seamlessly transitions to Castle’s ultra-efficient sensorless mode. You’ll put more power to the ground, where it should be, instead of wasting it through raw heat and RPMs. Application Guidelines: Mamba Monster X 8S and 1717-1650Kv motor is intended for use in 1:6 scale vehicles weighing up to 20 lbs. and running up to 8S LiPo. Also a great upgrade for heavier 1/8th vehicles. Features: ESC: Input Voltage Range 2S-8S LiPo Sensorless, Sensored and SmartSense™ Running Modes Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V) CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to  protect the electronics and promote efficient heat transfer Premium forged heatsink with elliptical fins for superior air flow and increased heat dissipation Oversized factory equipped thermally controlled 40MM cooling fan Compatible with S.BUS2 Telemetry Link and Futaba T4PX and T7PX transmitters Waterproof design for all weather conditions Data logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for "on-the-fly" adjustments using your transmitter Audible alerts for easy diagnosis of common issues such as motor-over-temperature and low-voltage cutoff Convenient transmitter programming for six common adjustable settings including cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store Proudly designed and manufactured in Olathe, KS USA and backed by Castle Creations' 1-year warranty Motor: 4-POLE 12-SLOT sensored design that boasts exceptional efficiency and produces less heat Proprietary stator winding produces low internal resistance for a cooler running motor Oversized NMB bearings and vibration dampening system ensure the longest possible bearing life High-strength, high-temperature grade neodymium sintered magnets combined with high-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions and high RPMs Specifications: ESC: Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes, waterproof Cooling Fan: Yes, factory equipped (40MM), fully removable** (see Product Use Statements below) Size: L x W x H 69.5mm x 54.1mm x 47mm Weight (with no battery connector): 5.75 oz. (163 grams) Connectors: 6.5mm female bullets for motor connection. Items Needed for Operation: A high current connector designed for high-powered electric systems, rated for 120+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors, soldered to the battery leads. Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately). Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters. Motor: Input Voltage Range: 3S-8S LiPo Kv: 1650 Max. RPM: 56,000 Size: Length: 3.35" (85.1mm) Diameter: 1.87" (47.6mm) Weight (w/wires):  21.08oz. /597.6g Shaft Diameter: 5mm Mounting Hole Specifications: M3 and M4@25.4mm (1.0") Diameter Cooling Fan: Not available Connectors: 6.5mm male connectors Application Guidelines: Ideal for vehicles up to 20lbs running 6s – 8s LiPo.  Examples include Losi LST2-E; Arrma™: Limitless™, Typhon™ 6s, Infraction™, Talion™ 6s; Traxxas: E-Maxx™, E-Revo™, UDR™, Summit™; Redcat Shredder™ ESC Product Use Statements: Recommended battery capacity for 1:6th scale vehicles is 5000mah. We recommend using 50C continuous discharge or higher LiPo batteries. Surge ratings should never be used to determine a pack’s suitability for a brushless application. Castle recommends a high current connector designed for high-powered electric systems, rated for 120+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors. Applying voltages higher than 33.6V will cause irreparable damage to ESC. Although Mamba Monster X 8S is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt. The ESC cooling fan must be removed prior to driving in wet conditions. It is not waterproof. Tech Notes: This motor includes 10AWG wire and 6.5mm connectors for use specifically this ESC/Motor combo. Running modes: SMARTSENSE™, Sensored, Sensorless with Castle sensored capable ESCs. Water Resistant Design: The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommended applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to this document for running and maintaining motors in wet environments. Includes: Mamba Monster X 8S ESC 4-POLE Sensored 1717-1650KV Motor Castle Sensor Harness Adapter 200mm Sensor Wire Mamba Decals Coupon for free Castle Link USB ESC Quick Start Guide Motor Quick Start Guide This product was added to our catalog on June 23, 2021

    1 in stock

    $399.99

  • TRA3045R, Traxxas LaTrax Waterproof Electronic Speed Control (w/Bullet Connectors) TRA3045R, Traxxas LaTrax Waterproof Electronic Speed Control (w/Bullet Connectors)

    Traxxas TRA3045R, Traxxas LaTrax Waterproof Electronic Speed Control (w/Bullet Connectors)

    12 in stock

    TRA3045R, Traxxas LaTrax Waterproof Electronic Speed Control (w/Bullet Connectors) LaTrax Waterproof ESC FeaturesInnovative waterproof designFully-proportional forward, reverse, and braking controlProgrammable with three drive profiles:Sport Mode – Fwd / Brake / RevRace Mode – Fwd / BrakeTraining Mode – 50% Fwd / Brake / 50% RevEZ-Set® push-button setupMulti-color LEDThermal shutdown protectionEfficient, low-loss MOSFET designBacked by the Traxxas Lifetime Electronics warranty This product was added to our catalog on September 7, 2021

    12 in stock

    $60.00

  • SPMXSE1130, Firma 130A Brushless Smart ESC, 2S-4S

    Spektrum SPMXSE1130, Firma 130A Brushless Smart ESC, 2S-4S

    Out of stock

    SPMXSE1130, Firma 130A Brushless Smart ESC, 2S-4S Spektrum Firma 130 Amp Brushless Smart ESC. Like every component in the Spektrum Smart ecosystem, Firma Smart ESCs combine "plug-and-play" simplicity with the ability to communicate with other Smart electronics — together, creating the best-performing RC system for your vehicle imaginable.Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best.With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity.Firma ESCs not only gather the data but also send it to your transmitter in real time, instead of only storing it for after-run study. You're able to adjust settings as needed to boost performance on the go. The Firma Smart single-wire telemetry solution has been tested for quality and performance by the best brands in RC. Their verdict? Smart technology is both simpler and superior!Features: Smart all-in-one telemetry Fast, powerful 32-bit ARM M4 processor Waterproof Multiple options for easy programming: Button programming Smart ESC Programming Box SmartLink USB Updating and Programmer application Multi-point protection: Over-current protection Automatic LiPo low-voltage cutoff Thermal protection Failsafe protection Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer Compact for easy installation in most applications Ready to install — no soldering required Rugged plastic case with mounting tabs Aluminum heat sink for high efficiency Cooling fan Adjustable high-power BEC Firmware updatable through the Smart ESC Programming Box High heat-resistant IC™ connectors, backwards compatible with EC™ connectors Limited 1-year warranty Specifications:Forward: YReverse: YBrake: YTime Delay Brake: YContinuous Maximum Current: 130A (760A Max Burst)Input Voltage: 7.4 - 14.8VInput Connector Types: IC5 with 12AWG, 160mm wireOutput Connector Types: 4.0mm Female Bullet with 12AWG, 150mm wireLength: 2.2in (57mm)Width: 1.4 (37mm)Height: 1.5in (38mm)Weight: 80g (2.8 oz)BEC Voltage: 6V (4A)Includes: (1) Spektrum™ Firma™ Smart ESC (1) Spektrum Smart sticker sheet (1) Product Manual This item was added to our collection May 3, 2023

    Out of stock

    $149.99

  • TRA3375, Traxxas Velineon VXL-3M Waterproof Brushless Electronic Speed Control TRA3375, Traxxas Velineon VXL-3M Waterproof Brushless Electronic Speed Control

    Traxxas TRA3375, Traxxas Velineon VXL-3M Waterproof Brushless Electronic Speed Control

    1 in stock

    TRA3375, Traxxas Velineon VXL-3M Waterproof Brushless Electronic Speed Control This is the Traxxas Velineon® VXL-3m forward/reverse brushless electronic speed control. This ESC simplifies brushless technology with easy, built-in profiles and intuitive programming. The VXL-3m™ uses advanced circuit design that allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. It sets up, operates, and programs just like the Traxxas XL-5™ family of ESCs so there's no tricky new procedures to learn. Traxxas' exclusive patent-pending Training Mode™ is also included to limit full throttle to 50% for young or inexperienced drivers. For the most advanced users, the VXL-3m is equipped with two-stage low voltage detection to allow LiPo battery use, including powerful 11.1-volt 3S packs! Features: Traxxas High-Current Connector maintains pure, unrestricted power flow from the battery to the brushless power system. Built-in two-stage low voltage detection for Lithium Polymer (LiPo) battery use provides a clear signal to the driver that the battery pack is nearing its minimum voltage threshold. Wide range of battery options, including 6-12 cell NiMH or NiCad packs The patent-pending Training Mode™ is an exclusive Traxxas feature that reduces the overall power output of the VXL-3m by 50%, making it easier for new or younger drivers to control their model. When they're ready, simply change profiles to unleash full-throttle action. Advanced circuit design allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. There's no need for additional sensor wiring and hardware complexity. The EZ-Set® push-button setup operates and programs just like other Traxxas speed controls such as the XL-5. This eliminates the need to learn a new set of procedures. The VXL-3m is programmable with three drive profiles: Sport Mode – Fwd / Brake / Rev Race Mode – Fwd / Brake Training Mode™ – 50% Fwd / Brake / 50% Rev Multi-color LED provides clear feedback Two-stage thermal shutdown protection protects the VXL-3m from overheating. Locked Rotor Protection™ prevents system damage by cutting power if the vehicle is stuck or the motor is bound. Battery Over-Voltage Protection™ causes the ESC to go into failsafe mode if the maximum input voltage is exceeded. Water resistant case design uses rubber seals and o-rings to protect against damage caused by water and moisture. Micro-fin aluminum heatsink dissipates heat. MOSFET design provides high-current output (326 amp peak) with incredibly low resistance (.0005 Ohm). Gold plated 3.5mm bullet connectors on 16-gauge Maxx® Cable flow full power to the motor without performance-strangling resistance. Specifications: Input voltage: 6 to 12 cells NiMH, 2S to 3S LiPo Case Size: 26.5mm W x 46.5mm D x 22mm H Weight: 38 grams Motors: Sensorless Brushless Motor Limit: None On Resistance: 0.0005 Ohms PWM Frequency: 12,000Hz Peak Current: 326A Continuous Current: 52A BEC Voltage: 6.0V DC Motor / Battery Wiring: 16-Gauge Maxx® Cable Transistor Type: MOSFET Low Voltage Detection: 2-Stage indicators, switchable (on or off) Thermal Protection: 2-Stage thermal shutdown Profile selection: Sport Mode: 100% fwd, 100% brakes, 100% rev Race Mode: 100% fwd, 100% brakes, no rev. Training Mode: 50% fwd, 100% brakes, 50% rev. Single-button setup: Yes, Traxxas EZ-Set® Battery Input Connector: Traxxas High-Current Connector Motor Connector: TRX 3.5mm Bullet Connectors This product was added to our catalog on July 17, 2021

    1 in stock

    $99.99

  • Sale -6% CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft) CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft)

    Castle Creations CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft)

    Out of stock

    CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft) The Castle Creations Mamba X SCT Waterproof 1/10 Brushless Combo includes the Mamba X, with the awesome 1415 Sensored motor to create a all in one system perfect for 2WD and 4WD Short Course trucks weighing up to 6.5lbs running on a 3s or 4s LiPo. The Mamba X is going to shake things up. Extremely versatile, and capable of powering a wide variety of applications and vehicles the Mamba X is ideal for racing at the track with your 2wd buggy, bashing through mud puddles in your monster truck, or navigating a hardcore trail with your crawler. The high performance Mamba X includes an integrated and powerful 8A adjustable BEC and can push the most extreme 1/10th scale setups and 1/8th scale race buggies. Castle Creations 1415 Sensored 4-Pole Brushless Motors combine rotor position sensor technology with an improved high power and high efficiency motor design to deliver ultra smooth startup, precise low speed control, predictable power delivery, incredible torque, and lightning fast response. Through the use of Castle's Smart Sense technology, the position of the rotor is always known by the ESC. This eliminates the possibility of encountering cogging or inconsistency during startup, and allows the 1406 to deliver PRECISE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for. Features: ESC Wide 2S to 6S input voltage range Sensored Motor Support (Castle X-Series Sensor Harness Included) Waterproof 8A Adjustable BEC (5.25V-8.0V) Data-logging Rugged CNC Aluminum Case Castle Link Programming Support SmartSense™ Integrated Capacitors Removable 30mm Cooling Fan Integrated 4mm Bullet Connectors 12 AWG Power Wires Waterproof Switch Audible Alerts The Mamba X is proudly designed and manufactured in Olathe, Kansas Backed by Castle Creations’ 1-year warranty and unparalleled "make-it-right" customer support Motor 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 13 AWG high strand wire with silicone insulation Kevlar wrapped rotor 6061-T6 Billet aluminum heatsink can High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: ESC Input Voltage Range: 2S LiPo (7.4V) to 6S LiPo (25.2V) BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes Cooling Fan: Yes, factory equipped (30mm), fully removable** (see Product Use Statements below) Size (LxWxH): 2.14x1.39x1.18" (54.4x35.2x30.0mm) Weight (with wires): 3.56 oz. (101g) Connectors: 4.0mm female bullets for motor connection. Items Needed for Operation: Battery Connector Application Guidelines: Intended for up to 6S (25.2 Volt) operation in vehicles weighing less than 9bs/4kg Recommended Motors: Castle 1406, 1410 and 1415 Sensored motors Max. Recommended Vehicle Weight: Less than 9bs/4kg, with batteries, ready-to-run Telemetry Link Capable: Yes Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free link included in package) and freely downloadable Castle Link Windows software. Motor Input Voltage Range: 3-4S LiPo Kv: 2400 Max. RPM: 75,000 Length: 69.5mm Diameter: 36mm Weight (w/wires): 319g / 11.3oz Shaft Length: 21mm Shaft Diameter: 0.197" (5mm) Mounting Hole: M3 @ 25mm Cooling Fan: Optional, coming soon! Connectors: 4mm male Castle Bullet Connectors Recommended ESC (s): Combo includes Mamba X ESC. Recommended Applications: 2WD and 4WD Short Course trucks weighing up to 6.5lbs running on a 3s or 4s LiPo with included 1415 - 2400kv sensored motor. Running Modes: SMARTSENSE™, Sensored, Sensorless Product Use Statements: *Although Mamba X is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC and motor with clean water after exposure to corrosives or dirt. While the motor and controller may be waterproof, Castle suggests users confirm that the rest of their vehicle, including the batteries, servos, radio and chassis are also waterproof before exposing them to liquids of any kind. **The cooling fan must be removed prior to driving in wet conditions. It is not waterproof. Tech Notes: Mamba X setups frequently hit 100+ amps in peaks and not all LiPos are created equal. Surge ratings should never be used to determine a pack's suitability for a brushless application. Recommended battery capacity for 1:10th and 1:8th scale vehicles is 5000mAh. We recommend using 30C continuous discharge or higher LiPo batteries (or high quality 25C batteries such as Traxxas® Power Cell). Our experience suggests using only mild gear ratios with NiMH cells. Do not attempt to use NiMH cells in extreme setups. Applying voltages higher than 25.2V will cause irreparable damage to ESC. We recommend a high-current connector designed for high-powered electric systems, rated for 70+ amps. Invest in connector sets made for high-powered electric systems such as our Castle 6.5mm Polarized Connectors, Castle 4.0mm Polarized Connectors, Traxxas® Power Connectors, or Deans® Ultra Plugs This product was added to our catalog on February 16, 2021

    Out of stock

    $292.95$275.00

  • AXI31620, Axial AE-6 ESC/Rx Combo AXI31620, Axial AE-6 ESC/Rx Combo

    Axial AXI31620, Axial AE-6 ESC/Rx Combo

    7 in stock

    AXI31620, Axial AE-6 ESC/Rx Combo The Axial AE-6 ESC/Rx is a replacement ESC/Receiver Combo intended for use with the Axial 1/24 Scale Deadbolt Mini Crawler. This package contains one ESC/Receiver Combo.NOTE: This ESC/Receiver is not compatible with the Axial SCX24 AXI00002V2T1 & AXI00002V2T2 models. This product was added to our catalog on June 5, 2021

    7 in stock

    $31.99

  • CSE011013700, ESC Cooling Replacement Fan :Mamba X CSE011013700, ESC Cooling Replacement Fan :Mamba X

    Castle Creations CSE011013700, ESC Cooling Replacement Fan :Mamba X

    5 in stock

    CSE011013700, ESC Cooling Replacement Fan :Mamba X

    5 in stock

    $12.95

  • ZTW-300-6300400, Seal Series ESC: 300A OPTO 6s-14s ZTW-300-6300400, Seal Series ESC: 300A OPTO 6s-14s

    ZTW ZTW-300-6300400, Seal Series ESC: 300A OPTO 6s-14s

    1 in stock

    Seal Series ESC: 300A OPTO 6s-14s Product Item   SEAL 300A OPTO HV 14S Model Number    6300400 Form Brushed / Brushless Brushless   HV / Normal HV Hardware Parameters Continuous Current (A) 300A   Burst Current(A) 1000A   Battery Cell (NiXX/Lipo) 18-42 NC/6-14 Lipo   BEC output / Dimensions Length 84mm   Width 146mm   Height 28.6mm   Weight 640g Wire & Plug Power Wire 8#AWG,160mm-Red/160mm-Black   Motor Wire 8#AWG,160mm-Black   Signal Wire 1 (Brown/Red/Orange)60C,add a special JR male connector at the end of 330mm wire   Signal Wire 2 (Brown/Red/Orange)30C,add a special JR male connector at the end of 150mm wire   Power Plug (Yes/No) no Parameter programming Transmitter  yes   Jumper  programming card      LCD programming card yes   WiFi programming card yes   USB adapter yes Firmware Upgrade Firmware online(Yes/No) yes Default Brake Type:  Brake OffBattery Type: LiPo with Automatic Cell detectiveCut Off Voltage Threshold:      3.0V/60%Motor Timing:  AutoMotor Rotation:  ForwardStart Up Strength:  30%Low Voltage Cut Off Type:   Reduce Power 18-42 NC/6-14 Lipo  

    1 in stock

    $374.99

  • CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor

    Castle Creations CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor

    Out of stock

    CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor The Castle Creations Mamba XLX 2 1/5 Scale Sensored Brushless ESC/Motor Combo with 2028 800Kv motor is a product guaranteed to redefine the limits of large scale R/C. Though it shares the name of its predecessor, the Mamba XLX, this is an ESC that lives in a class of its own. Reengineered from the ground up, the Mamba XLX 2 is packed with a potent combination of design, hardware and software advancements that will set a new standard for large-scale power systems. Designed for 1/5 Scale models weighing up to 42 lbs, the XLX 2 is an incredible power upgrade for the Losi DBXL-E and Super Rock Rey, Arrma Kraton 8S and Outcast 8S, or Traxxas X-Maxx models! If you are looking for the ultimate upgrade for your speed run, drag racing or off road rigs - the XLX 2 is a true heavyweight, with no contenders. CRYO-DRIVE: MORE POWER – COOLER TEMPS – LONGER RUNS Castle’s latest break-through technology, minimizes the amount of time the ESC’s electrical components spend generating heat. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 50mm fan and a forged elliptical fin heatsink, the design maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling. NOTE: Some vehicles may require aftermarket parts to allow ESC and/or motor fitment.  Features: Sensored, Sensorless and SmartSense™ running modes Powerful Integrated 20A Peak Adjustable BEC (5.25V-8.0V) Premium forged heatsink with for superior airflow and increased heat dissipation Oversized factory equipped thermally controlled 50mm fan  Waterproof design for all weather conditions.  ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to  protect the components and promote efficient heat transfer Data-logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for “on the-fly” adjustments using your transmitter Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options.   Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming  with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store. Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1-year warranty Specifications: ESC: Input voltage range: 3S-8S LiPo Length: 3.98” (101.2mm) Width: 2.49” (63.3mm) Height: 2.2” (55.8mm) On/Off Switch: Yes, waterproof* Cooling Fan: Yes, thermally controlled factory equipped (50mm) fully removable** Weight: 13.1 oz (371g) Running Modes: Sensored, Brushed, Sensorless and SmartSense™ when paired with a Castle 4-POLE 12-SLOT Sensored Motor. (Dust cover included in package for non-sensored operation) Wire Gauge: 8AWG Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX, T7PXR Transmitters. Items Needed: Battery connectors designed for 150+ amps continuous, such as Castle 6.5mm polarized or CC BULLET 8.0MM Motor: Application Guidelines: 1:5th Scale vehicles weighing up to 30 lbs.  Vehicle Examples: Losi DB XL-E,™ Losi Super Rock Rey™, Arrma Kraton 8s™, Arrma Outcast 8s™, Traxxas X-Maxx™ (Some vehicles may require aftermarket parts to allow ESC and/or motor fitment) Input Voltage Range: MIN: 3S LiPo, MAX: 8S LiPo 33.6V Kv: 800Kv Max. RPM: 45,000 Diameter: 2.22” (56.3mm) Length: 4.44” (112.7mm) Shaft Size: 30mm (Length), 8mm (Diameter) Weight (w/wires): 44 oz./1.25kg Mounting Hole Specifications: Holes: 4mm, Spacing: 30mm Connectors: 8.0mm male connectors, 300mm Direct Connect Sensor Wire Includes: Mamba XLX2 ESC 2028-800kv Sensored Brushless Motor 300mm Direct Connect Sensor Wire Mamba Decals Mamba XLX2 Quick Start Guide Sensor port dust cover Coupon for free Castle Link USB This product was added to our catalog on October 12, 2021

    Out of stock

    $499.99

  • SPMXSE1150, Spektrum RC Firma 150 Amp Brushless Smart ESC SPMXSE1150, Spektrum RC Firma 150 Amp Brushless Smart ESC

    Spektrum SPMXSE1150, Spektrum RC Firma 150 Amp Brushless Smart ESC

    Out of stock

    SPMXSE1150, Spektrum RC Firma 150 Amp Brushless Smart ESC Spektrum Firma 150 Amp Brushless Smart ESC. Like every component in the Spektrum Smart ecosystem, Firma Smart ESCs combine "plug-and-play" simplicity with the ability to communicate with other Smart electronics — together, creating the best-performing RC system for your vehicle imaginable. Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best. With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity. Firma ESCs not only gather the data but also send it to your transmitter in real time, instead of only storing it for after-run study. You're able to adjust settings as needed to boost performance on the go. The Firma Smart single-wire telemetry solution has been tested for quality and performance by the best brands in RC. Their verdict? Smart technology is both simpler and superior! Features: Smart all-in-one telemetry Fast, powerful 32-bit ARM M4 processor Waterproof Multiple options for easy programming: Button programming Smart ESC Programming Box SmartLink USB Updating and Programmer application Multi-point protection: Over-current protection Automatic LiPo low-voltage cutoff Thermal protection Failsafe protection Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer Compact for easy installation in most applications Ready to install — no soldering required Rugged plastic case with mounting tabs Aluminum heat sink for high efficiency Cooling fan Adjustable high-power BEC Firmware updatable through the Smart ESC Programming Box High heat-resistant IC™ connectors, backwards compatible with EC™ connectors Limited 1-year warranty Includes: (1) Spektrum™ Firma™ Smart ESC (1) Spektrum Smart sticker sheet (1) Product Manual Specifications: Forward: Y Reverse: Y Brake: Y Time Delay Brake: Y Continuous Maximum Current: 150A (950A Max Burst) Input Voltage: 11.1 - 22.2V Input Connector Types: IC5 Output Connector Types: 6.5 Female Bullet Length: 58mm (2.3in) Width: Case = 47.5mm (1.9in) W/ Tabs = 59.5mm (2.3in) Height: 38.5mm (1.5in) Weight: 238g (8.4 oz) BEC Voltage: 6V (5A) This product was added to our catalog on March 12, 2021

    Out of stock

    $159.99

  • TRA3496, Traxxas X-Maxx Velineon VXL-8s Waterproof ESC TRA3496, Traxxas X-Maxx Velineon VXL-8s Waterproof ESC

    Traxxas TRA3496, Traxxas X-Maxx Velineon VXL-8s Waterproof ESC

    4 in stock

    TRA3496, Traxxas X-Maxx Velineon VXL-8s Waterproof ESC This is the Traxxas X-Maxx Velineon VXL-8s Waterproof ESC. The Velineon VXL-8s forward/reverse electronic speed control simplifies brushless technology with easy, built-in profiles and intuitive programming. The VXL-8s uses advanced circuit design that allows sensorless brushless motors to operate with the smoothness and precision of the best brushless systems. The VXL-8s comes with the peace-of-mind of the Traxxas Lifetime Electronics Warranty and unmatched Traxxas customer support. The VXL-8s is not a toy. It is a sophisticated electronic device capable of delivering large amounts of current. Children under 14 years of age require adult supervision for use of the VXL-8s.  Real-Time TelemetryThe VXL-8s now supports real-time telemetry capability using the optional 6511 Wireless Module (sold separately) installed in a Traxxas TQi transmitter. Use the free Traxxas Link App to download the telemetry update to the ESC. Receive speed, RPM, voltage and ESC temperature telemetry directly on your mobile device while you drive and best of all, no additional sensors are required. The Traxxas Link App makes it easy to update your VXL-8s with the newest features. Specifications: Input voltage: 4S/6S/8S LiPo (max. 33.6 volts) Supported motors: Sensorless brushless Battery connectors: Traxxas High-Current Connector Motor connectors: TRX 6.5mm bullet connectors Motor/battery wiring: 10-gauge Maxx® Cable Thermal protection: 2-stage thermal shutdown Case size (l/w/h): 58mm (2.28”)/ 72mm (2.83”)/ 46mm (1.81”) Weight: 182g (6.42oz) This product was added to our catalog on April 12, 2021

    4 in stock

    $249.99

  • COR54001, Corally CORA 40-Brushed ESC, 2-3S: SP Versions

    Corally COR54001, Corally CORA 40-Brushed ESC, 2-3S: SP Versions

    Out of stock

    COR54001, Corally CORA 40-Brushed ESC, 2-3S: SP Versions Max. Cont. Current (A): Forward: 40 A / Reverse: 20 A Motor Limit: 2S = 12T 3S = 18T Input Voltage (V) min. - max.: 5-12.6 V Max. Current (A): Forward: 180 A / Reverse: 90 A Resistance: Forward: 0.002 Ohn / Reverse: 0.004 Ohm Length (mm): 46.5 mm Nr of Li-xx Cells: 2-3S Width (mm): 34 mm Nr of Ni-xx Cells: 5-9 Cell NiMH Motor Type: Brushed Height (mm): 28.5 mm BEC Voltage (V): 6 V BEC Current (A): 2 A Weight incl. wire (g): 65 g Programmable: Jumper Throttle Mode: Forward / Reverse programmable Reverse lockout Battery Mode: NiMH / LiPo Cut off voltage: NiMH mode = 4.5 V Lipo Cut off: 2S = 6.5 V 3S = 9.75 V Thermal Protection Temperature: 105 Degrees C Water Protection: Yes Connector (Motor): 4 mm Connector (Battery): Tamiya style Motor wire size: 16 AWG Battery wire size: 16 AWG Car Type Use: 1/10th scale This product was added to our catalog on January 18, 2022

    Out of stock

    $37.99

  • HWA30102601, EzRun MAX10 SCT Sensorless Brushless ESC (1/10 SCT)

    HobbyWing HWA30102601, EzRun MAX10 SCT Sensorless Brushless ESC (1/10 SCT)

    Out of stock

    Built with the most rugged and high-quality components and coupled with cutting-edge firmware, the EzRun MAX10 SCT is able to deliver unmatched power and performance for even the most hardcore applications. With incredible acceleration capabilities and a rock-solid, stable output, the MAX10 SCT can handle instant full-torque start-ups for wheelies, high-speed racing on straightaways, and powering through the bumpiest terrian. The MAX10 SCT features an electronic switch with a lifespan of over 50000 on/off cycles, housed in a completely waterproof, dust-prood and shock-resistant design. Features: Cont./Peak Current: 120A/760A Input: 2-4S LiPo/6-12 Cells NiMH BEC Output - Switch Mode: 6V/7.4V,3A Size: 49.0x39.5x34.7mm Weight: 105g KV Rating: 2S LiPo: up to 6000KV, 3S LiPo: up to 4000KV, 4S LiPo: up to 3000KV (36XX Series of Motors)

    Out of stock

    $99.99

  • REDRER09469, Hobbywing 60A Brushless Speed Controller (Sensorless)

    Redcat Racing REDRER09469, Hobbywing 60A Brushless Speed Controller (Sensorless)

    Out of stock

    PRODUCT FEATURES Hobbywing 60A Brushless Speed Controller (Sensorless) Splashproof Deans Connector/T-Plug WARNING: These Electronics CAN NOT be submerged! Specifications: Maximum continuous current: 60A Maximum burst current: 390A Input: 2-3S LiPO***, 4-9 cell NiCD/NiMH*** Motor limit (2S LiPO, 4-6 cell NiCD/NiMH): 4500kv Motor limit (3S LiPO, 7-9 cell NiCD/NiMH): 3500kv BEC: 3A/6V switching type Dimensions: 48.5*38*32mm Weight: 90g Motor Plugs: 4mm female bullet  Battery Plug: Deans/T-Plug ***Only 2S LiPO or 6-7 cell NiMH/NiCD battery packs are recommended for Redcat Racing vehicles that use this ESC. Using more voltage than what we recommend will void all warranties and is at your own risk!***

    Out of stock

    $73.99

  • RER06910, Redcat Hobbywing 1/10 Brushed Waterproof ESC

    Redcat Racing RER06910, Redcat Hobbywing 1/10 Brushed Waterproof ESC

    1 in stock

    REDRER06910, Redcat Hobbywing 1/10 Brushed Waterproof ESC This product was added to our catalog on January 21, 2022

    1 in stock

    $37.99

  • REDB7003SR, Redcat, Brushed Electronic Speed Controller with Banana Connector

    Redcat Racing REDB7003SR, Redcat, Brushed Electronic Speed Controller with Banana Connector

    1 in stock

    Brushed Electronic Speed Controller with Banana Connector (Use B7003SR-T for T-Plug battery connector) Programmable (On/Off) Li-Po battery voltage cut-off and reverse Fits all Ground Pounder models

    1 in stock

    $31.99

  • ARAM2000, AR390211 BLX185 6S ESC

    ARRMA ARAM2000, AR390211 BLX185 6S ESC

    Out of stock

    ARAM2000, AR390211 BLX185 6S ESC Product Details The BLX185 150A waterproof ESC provides consistent power control and is 6S LiPo ready. Fitted with super-reliable XT-90 connectors and sporting a built-in cooling fan for reduced heat during intense driving action, the BLX185 ESC has over voltage protection, and a two-stage LiPo cut off for added cell management.The fitted 10AWG high-quality wires and 6V BEC unit are combined with a three mode throttle profile (FWD/REVERSE/BRAKE) to provide the ultimate driving experience.Recommended battery specification: 5000mAh - 35C minimum - Per battery pack 3S, 4S and 6S LiPo Compatibility

    Out of stock

    $139.99

  • ZTW-SEAL-CARD-180000010, Seal Series: Program Card for Seal ESCs ZTW-SEAL-CARD-180000010, Seal Series: Program Card for Seal ESCs

    ZTW ZTW-SEAL-CARD-180000010, Seal Series: Program Card for Seal ESCs

    3 in stock

    Seal Series: Program Card for Seal ESCs Stand alone programming card for the ZTW Seal Esc's. Allows quick and easy option programing without the need of a computer. And if you want to connect to the computer for an esc firmware upgrade or to read options, you can with the included pc cable (4 cell rx pack required). Notes: When using this with the Seal 300HV or 500HV Esc. You will also need a 4cell AA receiver pack to power the programmer. Otherwise the other esc's with built in battery eliminator circuits (bec) will supply power to the programmer.

    3 in stock

    $54.99

  • Sale -29% HWA30113301, XeRun XR8 SCT Pro Brushless ESC

    HobbyWing HWA30113301, XeRun XR8 SCT Pro Brushless ESC

    Out of stock

    HWI30113301, XeRun XR8 SCT Pro Brushless ESC Features: Cont./Peak Current: 140A/880A Motor Type: Sensored / Sensorless Brushless Motor Cells: 2-4S LiPo, 6-12Cell NiMH BEC Output: 6V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC) ESC programming: LCD Program box, WiFi module enabled (Sold seperately) Main Applications: 1/8th Buggy Competition, 1/10th STC, Monster Truck, On-road, Buggy, Truggy

    Out of stock

    $163.00$114.99

  • SPMXSE1160, Spektrum RC Firma 160 Amp Brushless Smart ESC SPMXSE1160, Spektrum RC Firma 160 Amp Brushless Smart ESC

    Spektrum SPMXSE1160, Spektrum RC Firma 160 Amp Brushless Smart ESC

    2 in stock

    SPMXSE1160, Spektrum RC Firma 160 Amp Brushless Smart ESC Spektrum Firma 160 Amp Brushless Smart ESC. Like every component in the Spektrum Smart ecosystem, Firma Smart ESCs combine "plug-and-play" simplicity with the ability to communicate with other Smart electronics — together, creating the best-performing RC system for your vehicle imaginable. Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best. With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity. Firma ESCs not only gather the data but also send it to your transmitter in real time, instead of only storing it for after-run study. You're able to adjust settings as needed to boost performance on the go. The Firma Smart single-wire telemetry solution has been tested for quality and performance by the best brands in RC. Their verdict? Smart technology is both simpler and superior! Features: Smart all-in-one telemetry Fast, powerful 32-bit ARM M4 processor Waterproof Multiple options for easy programming: Button programming Smart ESC Programming Box SmartLink USB Updating and Programmer application Multi-point protection: Over-current protection Automatic LiPo low-voltage cutoff Thermal protection Failsafe protection Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer Compact for easy installation in most applications Ready to install — no soldering required Rugged plastic case with mounting tabs Aluminum heat sink for high efficiency Cooling fan Adjustable high-power BEC Firmware updatable through the Smart ESC Programming Box High heat-resistant IC™ connectors, backwards compatible with EC™ connectors Limited 1-year warranty Specifications: Forward: Y Reverse: Y Brake: Y Time Delay Brake: Y Continuous Maximum Current: 160A (1050A Max Burst) Input Voltage: 11.1 - 29.6V Input Connector Types: IC5 Output Connector Types: Female 6.5 Bullets Length: 70 Width: 77 Height: 44 Weight: 280g BEC Voltage: 6V / 8.4V Includes: (1) Spektrum™ Firma™ Smart ESC (1) Spektrum Smart sticker sheet (1) Product Manual This product was added to our catalog on October 23, 2021

    2 in stock

    $219.99

  • CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV) CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV)

    Castle Creations CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV)

    Out of stock

    CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV) The Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo with 2028 Sensored Motor is a great way to take your build to the next level with Castle’s cutting edge sensored large scale brushless power. The MAMBA MONSTER X 8S COMBO is ready to power any R/C vehicle weighing up to 25lbs, and running all the way up to 8S LiPo. This motor and ESC combo is designed for heavy, high speed rigs, and you'll experience smooth low-end control, without sacrificing power, punch, or speed. The MAMBA MONSTER X 8S utilizes Castle’s breakthrough technology, CRYO-DRIVE. By reducing the rate at which the ESC heats up and removing heat more efficiently, your setup will be able to handle higher gear ratios, in heavier vehicles, with longer runs. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 40mm cooling fan and a forged elliptical fin heatsink, the design maximizes airflow throughout the system, taking thermal performance to a whole new level. The ESC was designed with a robust aluminum casing, and the epoxy potting guarantees protection around the circuitry and ensures all-weather use. Mamba Monster X 8S is a beast, ready to take on the harshest of environments and still perform. You can easily optimize the ESC for any driving condition, from rugged terrain to smooth pavement to the perils of rock and gravel. Create, save and download setup profiles through the Castle Link Programming Suite on your Windows™ PC, or wirelessly with the convenience of the new B-Link™ Bluetooth™ Adapter and Castle Link app for Android or iOS. When paired with the Castle sensored 2028-800KV motor, users with heavy, high power rigs will experience controllable low-end control without sacrificing power, punch or speed. SmartSense™ mode uses the motor’s sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is spinning, it seamlessly transitions to Castle’s ultra-efficient sensorless mode. You’ll put more power to the ground, where it should be, instead of wasting it through raw heat and RPMs. NOTE: This is not a direct replacement to the Mamba XLX. The XLX still handles rawer full throttle power in the most extreme setups. Features: ESC: Input Voltage Range 2S-8S LiPo Sensorless, Sensored and SmartSense™ Running Modes Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V) CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the electronics and promote efficient heat transfer Premium forged heatsink with elliptical fins for superior air flow and increased heat dissipation Oversized factory equipped thermally controlled 40MM cooling fan Compatible with S.BUS2 Telemetry Link and Futaba T4PX and T7PX transmitters Waterproof design for all weather conditions Data logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for "on-the-fly" adjustments using your transmitter Audible alerts for easy diagnosis of common issues such as motor-over-temperature and low-voltage cutoff Convenient transmitter programming for six common adjustable settings including cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store Proudly designed and manufactured in Olathe, KS USA and backed by Castle Creations' 1-year warranty Motor: The 2028 Extreme can easily run in the 10 horsepower range (Burst power output for duration's typical of vehicle acceleration.) Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Proprietary winding techniques allow Castle Creations to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Dual sensor ports to ensure optimal installation in your large-scale vehicle. Updated modern and sleek design that looks as cool as it performs. Specifications: ESC: Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes, waterproof Cooling Fan: Yes, factory equipped (40MM), fully removable** (See Product Use Statements below) Size: L x W x H 69.5mm x 54.1mm x 47mm Weight (with no battery connector): 5.75 oz. (163 grams) Connectors: 6.5mm female bullets for motor connection Motor: Input Voltage Range: 12S MAX Kv: 800 Max. RPM: 45,000 Minimum Input Voltage: 3S Maximum Input Voltage: 12S Sensored Capable: Yes Can Length: 4.4" (113.2mm) Can Diameter: 2.2" (57mm) Weight (w/wires): 44 oz./1.25kg Shaft Size: Length: 30mm Diameter: 8mm Mounting Hole Specifications: 4mm holes @ 30mm spacing. Cooling Fan: Available, but not included. See 011-0019-00 here. Connectors: 8.0mm male connectors Recommended ESC: Mamba XL X Running modes: Sensorless and Sensored Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs. Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately). Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters. Product Use Statements: Recommended battery capacity for 1:6th scale vehicles is 5000mah. Castle recommends using 50C continuous discharge or higher LiPo batteries. Surge ratings should never be used to determine a pack’s suitability for a brushless application. Castle recommends a high current connector designed for high-powered electric systems, rated for 100+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors. Applying voltages higher than 33.6V will cause irreparable damage to ESC. Although Mamba Monster X 8S is waterproof, it is NOT intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt. The cooling fan must be removed prior to driving in wet conditions. *Fan is not waterproof. Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the motor or ESC. The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the Running & Maintaining document in the resources tab above for info on running and maintaining motors in wet environments. Application Guidelines: Mamba Monster X 8S and 2028-800Kv motor is intended for use in 1:6 scale vehicles weighing up to 25 lbs. and up to 8S LiPo. Vehicle Examples: Traxxas™ X-Maxx & Unlimited Desert Racer; Arrma™ Kraton 8s & Limitless; Losi™ Super Rock Rey & Audi R8; Redcat™ Shredder (optional motor mount and modifications may be necessary to install motor). Includes: Mamba Monster X 8S ESC 4-POLE Sensored 2028-800KV Motor Castle Sensor Harness Adapter (installed) 250mm Sensor Wire Mamba Decals Coupon for free Castle Link USB ESC Quick Start Guide Motor Quick Start Guide This product was added to our catalog on April 4, 2021

    Out of stock

    $454.99

  • HWA38010802, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/5687SL (1100kV) HWA38010802, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/5687SL (1100kV)