EFLB2001S45, E-flite 1S LiPo Battery 45C (3.7V/200mAh)
A replacement 200mAh 45C 1s (3.7V) Li-Po Battery from E-Flite. Suited for use with the Inductrix FPV, and many other applications that commonly accept a 150-210mAh sized battery.
This product was added to our catalog on October 14, 2021
EFLB5001S25, E-flite 1S 25C LiPo Battery Pack (3.7V/500mAh) w/JST Connector
This is a replacement E-flite 1S - 3.7V, 25C, 500mAh LiPo Battery Pack.
Specifications:
Type: LiPo
Capacity: 500mAh
Voltage: 3.7V
Weight: 0.51 oz (14.5 g)
Configuration: 1S
Length: 2.35 in (59.5mm)
Width: 0.75 in (19.0mm)
Height: 0.30 in (7.5mm)
Maximum Continuous Discharge: 25C
Maximum Continuous Current: 12.5A
This product was added to our catalog on December 20, 2021
PTK-5184, ProTek RC 1S High Power Micro Heli/Airplane 25C LiPo Battery (3.7V/160mAh)
This is the ProTek R/C 1S 160mAh, 25C Micro Helicopter/Airplane Lithium Polymer battery pack. This pack will fit E-Flite and Parkzone products that use 70mah to 150mAh battery packs. When used in aircraft that normally use 70mAh batteries, these batteries will provide better performance and longer flight times!
Specifications:
Type: Lithium Polymer
Capacity: 160 mAh
Voltage: 3.7V nominal
Connector Type: Molex
Number of Cells: 1
Weight: 4g
Dimensions: 43x12x5mm (1.75x.5x.25")
Maximum Charge Rate: 1C (160mAh)
Maximum Continuous Discharge: 25C (4.0A)
This product was added to our catalog on May 18, 2021
BLH4210, Blade 1S 40C LiPo Battery (3.7V/150mAh)
This is a replacement Blade 1S 40C LiPo Battery with 150mAh capacity.
NOTE: For use with Blade BLH4211 USB Charger.
This product was added to our catalog on April 27, 2021
TRA6637, Traxxas LaTrax Alias LiPo Battery (3.7V/650mAh)
This is a replacement LaTrax 3.7V 650mAh 1C LiPo battery pack for use on the La Trax Alias quad-copter.
Specifications:
Length: 2.08" (53mm)
Width: 1.18" (30mm)
Thickness: 0.23" (6mm)
This product was added to our catalog on September 7, 2021
HWA30112751, Hobbywing Xerun XR10 Pro 1S Stock Spec 1/12 Sensored Brushless ESC
The Hobbywing Xerun XR10 Pro 1S Stock Spec 1/12 Sensored Brushless ESC is super small in size and at 31.6x25.8x16.2mm size, is 20% smaller than the standard version XeRun XR10 Pro 1S. Plus, the light weight (only 23.5g w/o wires) provides more weight margin when adjusting the balance of the chassis.
Features:
Special Design for Stock 1S Class Racing: Reliable hardware combined with powerful software (contains 5 common select-to-use profiles) provides an ideal power solution for 1/12th Stock 1S class racing
Super Internal BEC: The built-in boost BEC with a maximum output of 6A and voltage adjustable between 6V and 7.4V allows users to use various, servos and receivers (without connecting any extra battery).
Adjustable Throttle & Brake PWM Frequencies: The independent and adjustable throttle & brake PWM frequencies guarantee precise and accurate throttle and brake control.
Programming/Upgrading/Data Reading Wirelessly: With Hobbywing's optional "WiFi Express" module (HWA30503000 - not included) and iPhone or an Android phone (with the HOBBYWING WiFi Link software installed), the user can remotely program parameters, upgrade firmware and check relevant data of the ESC without leaving the control stand.
Built-in Electronic Switch: The internal electronic switch with a lifespan of over 50,000 on/off cycles completely solves the problems like stuck reed, rust contact points, and automatic shutdown that conventional mechanical switches often have.
Data-logging Capability: This ESC features the data-logging function which will record the maximum ESC & motor temperatures, the maximum motor RPM, and etc. in real time and allows users to check those data via a LCD program box or WiFi module after each use.
Specifications:
Cont./Peak Current: 80A/380A
Input Voltage: 1S Lipo/3-4 Cell NiMH
BEC Output: 6V/7.4V@3A
Wires: Black-14AWG-200mm
Connectors: No
ESC Programing: LCD Program Box or WiFi Module
Firmware Upgrade Supported: Yes
Size: 31.6x25.8x16.2mm
Weight: 23.5g (w/o Wires)
Applications: Stock 1S class of 1/10th & 1/12th on-road racing.
KV Rating/T Count: ≥10.5T, 3650-size Motor
This product was added to our catalog on May 3, 2023
All batteries must be shipped by a ground shipping method.
The Cetus Pro FPV Kit is finally here! It is the best ideal choice for beginners to advance currently. Comes with a Cetus Pro brushless quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles. It's more powerful and maneuverable for all starters as well as FPV pros to practice indoor and outdoor.
Be sure to pick up some extra batteries so that you can fly all day! We recommend the following 1S batteries for this quad:
BetaFPV 1S 450mAh - BT2.0
Check out our other RTF combos, all our pre-built quads and our BetaFPV selection!
Features
The auxiliary flight function is greatly reducing the threshold of operating. This is the lightest key to open the door to advanced FPV.
Cetus Pro quadcopter comes with a brushless power system, it's more powerful and maneuverable in flight. Pilots can achieve more FPV freestyle actions to train.
With the self-protection of emergency landing when out of control or in low battery, to ensure a more safe flight.
Made of PA12 material, the frame has an excellent impact resistance in drop & impact. Meanwhile, the 360° protection of the whoop frame ensures safe flights both indoors and outdoors.
All items needed for the flight are packed in an EVA portable storage bag. Better to protect and convenient to carry.
Specifications
BetaFPV LiteRadio 2
Frequency Range: 2.4GHz (2403MHz-2447MHz)
2.4G System: NRF24L01 or CC2500
Channel: 8
Support Protocol: Bayang / Futaba S-FHSS / Frsky D16 FCC/ Frsky D16 LBT/ Frsky D8
Power: ≤100mw
Adapted Drone Type: Multirotor
Support USB Charging / Firmware Update
Support BETAFPV Simulator Connected / Customized LiteRadio System / Joystick Calibration
LED Light: Green-Power On / Red-Warning / Blue-Normal
Battery: Built-in 1000mAh 1S Battery
Charging Connector: Type-C
BetaFPV VR02 Goggles
Screen Size: 4.3"
Screen Resolution: 800x480p
Screen Brightness: 300cd/m2
Field of View: 55°
Charging Port: USB-C
Input Voltage: 3.7V 500mA
Internal Battery: 3.7V 2000mAH
Dimensions: 143x126x86.3mm
Weight: 300g
BetaFPV RTF Cetus Pro
Positioning system: Optical flow / Barometer / Laser
Height Positioning: Laser / Barometer
Angle Locating: Optical flow ( effective height 0.3-3m)
Accuracy of auto-hover: Horizontal ±0.2m, vertical ±0.3m (under no wind environment)
Receiver protocol: Frsky D8
VTX: 25mW
Camera tilt degree: 25°
Camera: C02 FPV Micro Camera
Propeller: 40mm 3-blade 1.5mm shaft hole
Power system: 1S
Battery: BT2.0 450mah 1S Battery (external)
Flight time: 4-5min
Flight distance: 80m (Clear line of site)
Includes
1x Cetus Pro Brushless Quadcopter
1 LiteRadio2 SE Transmitter (Frsky D8 Protocol)
1x VR02 FPV Goggles
2x BT2.0 450mAh 1S Lipo Battery
1x BT2.0 Battery Charger and Voltage Tester
1x USB Charging Cable (Type-C)
1x Type-C Adapter
1x Prop Removal Tool
1x Portable Storage Bag
M03 VTX, an ultralight and high output power 5.8GHz analog VTX, is designed for 65-85mm whoop drone for longer-range flying.
Check out all our Micro/Nano VTXs and all our BetaFPV gear!
Features
With the 25-350mW output power, the M03 VTX provides a stable image and strong transmission.
Only 1.1g and a tiny size for drones like 65-85mm whoop drones. The screw mounting holes pattern is suitable with BETAFPV micro canopy. The camera connector JST-0.8 is suitable for the BETAFPV C02 camera.
Comes with IPX type of antenna, just plug and play, no extra solder work needed.
M03 VTX is perfectly suitable for the 65-85mm whoop drone. We highly recommend using it with ELRS 2.4G FC board, like F4 1S 5A FC (ELRS 2.4G) or F4 1S 12A FC (ELRS 2.4G).
Diagram
Below is the diagram of the M03 VTX. The camera connector is JST-0.8 and it is compatible with cameras like BETAFPV C01, BETAFPV C02, and NewBeeDrone BeeEye.
How to connect with the Flight Controller
Here is the diagram about how to connect the M03 VTX with F4 1S 5A FC (ELRS 2.4G) board.
Here is the diagram about how to connect the M03 VTX with F4 1S 12A FC (ELRS 2.4G) board.
Change Band & Band & Chnanel & Power
M03 VTX could only use the Smart Audio port to change the band and channel. Enter the OSD menu by radio transmitter sticks ( Pitch Stick UP and Yaw Stick Left). Then FEATURES -> VTX SA to change the frequency point and power.
Switchable power includes 25mW, 100mW, 200mW and 350mW. Except for the method via OSD menu as show above, the output power could be changed via the power button.
Specifications
Item: M03 5.8G VTX
Output power: 25/100/200/350mW (adjustable)
Supply voltage range: 4.5-5.5V
Weight: 1.1g (antenna not included)
VTX internal size: 18X14mm
Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz
Channel SEL: SmartAudio
Modulation type: FM
Frequency control: PLL
All harmonic: Max -50dBm
Frequency stability: ±100KHz (Typ.)
Frequency precision: ±200KHz (Typ.)
Channel carrier error: ±1.5dB
Antenna port: 50 Ω
Operating temperature: -10℃~+80℃
Camera connector: JST-0.8, compatible with cameras like BETAFPV C01, BETAFPV C02 and NewBeeDrone BeeEye.
Includes
1x BetaFPV M03 25-350mW 5.8G Micro VTX - U.FL
5x 30AWG silicone wire (30mm)
BLH4211, Blade USB 1S LiPo Battery Charger
This is a replacement Blade USB 1S LiPo Battery Charger, for use with the 70 S Helicopter. This charger is only intended for 1S, 3.7V 70 S LiPo battery (BLH4210).
This product was added to our catalog on April 27, 2021
Pre-orders shipping ASAP! All products with batteries must be shipped by a ground shipping method.
The BetaFPV Meteor65 is a leading 1S whoop WINTER TIME drone. This 22.83g lightweight whoop drone comes with a completely new look and a special micro canopy, supporting the serial ExpressLRS 2.4G, Frsky, or TBS RX version. It is equipped with the BT2.0 connector, the lightest F4 1S 5A FC (2022), new 0802SE 19500KV motors, and C03 FPV camera. With the combination of those electronics and parts, it reaches the best balance between performance, weight, durability, and premium build design.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features
Meteor65 is the first generation whoop drone powered by a brand-new BT2.0 1S battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector.
By using the latest 0802SE 19500KV motors and 31mm 3-blade props, this kit provides you with a completely different experience of a powerful indoor flight.
Built-in 1.52g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopted with an injection molding technique, the canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, and provides good protection for the whoop drone.
F4 1S 5A FC (Serial ELRS 2.4G) is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.
The various colors of the spare parts including the 65mm frame, micro canopy, and propellers offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.
Let's see what's new in Meteor65 2022 version. It comes with a new micro canopy, which reduces the influence of heat on electronics. Supports serial ExpressLRS 2.4G instead of SPI ERLS 2.4G. And the new C03 FPV Camera ensures a high-quality and clear image.
Meteor65 (2022)
Meteor65 (2021)
FC&ESC
F4 1S 5A FC (2022)
F4 1S 5A FC
RX
Serial ELRS 2.4GHz
SPI ELRS 2.4G
Camera
C03 FPV Camera
C02 FPV Camera
Motors
New 0208SE 19500Kv (Ice Blue)
0208SE 19500Kv (Black Version)
Canopy
New Micro Canopy (2022)
Micro Canopy
Tilt
20° or 30°
30°
Weight
22.83g (without battery)
22.84g (without battery)
Flight Time
4 mins
3.5-4 mins
BETAFPV upgraded all Meteor Series quadcopters like Meteor65, Meteor65 Pro, Meteor 75, and Meteor85 whoop quadcopters, through the new flight controller, motors, camera, frame, canopy, etc, to provide the best whoop quadcopters for pilots.
BT2.0 Connector
BETAFPV exclusively designed BT2.0 connector has broken through the bottle-neck of PH2.0 connector. The BT2.0 connector has decreased internal resistance of the connector effectively allowing more current to be transferred, which means it supports 9A continuous current (15A burst). This means stronger power and longer flight time on 1S brushless drones while PH2.0 just supports 4.5A. You can enjoy more flight time without being disturbed by low voltage warnings due to reducing voltage sag.
See the graph below comparing the BT2.0 connector and PH2.0 connector (solid pin version) in BETAFPV 1S 300mAh battery. The discharge current is 9A in this test. The BT2.0 has double the time (about 2 minutes) and a 0.2v improvement in voltage sag.
Flight Controller & ESC
The latest F4 1S 5A flight controllers are applied to all BNF versions of the Meteor65. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. They updated the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor65 (ELRS)
Meteor65 (FrSky, PNP, TBS)
FC Inside
F4 1S 5A FC (Serial ELRS 2.4GHz)
F4 1S 5A FC (SPI FrSky)
Gyro
BMI270
BMI270
FC Firmware
BetaFPVF411
BetaFPVF411RX
UART Ports
One UART Port
Two UART Ports
External RX
Not Supported
Supported
Note: For F4 1S 5A FC (serial ELRS 2.4G), ONLY Betaflight firmware 4.3.0 and up start to support BMI270 gyro. For F4 1S 5A FC (SPI Frsky), we recommend using BETAFPVF411RX 4.2.11 firmware and CLI dump file offered by BETAFPV. If you update the 4.3.0 and up firmware for serial ELRS 2.4G from the Betaflight official site, please flash the CLI dump file for Meteor65.
C03 Camera
The C03 FPV Micro Camera is 1.52g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.
Motors
The 0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight which is only 1.88g/pc but also ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.
Meteor65 Frame
The lightest lower profile 65mm frame - Meteor65 frame is 3.25g only. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. There are more options for colorful frames such as Beta-blue, mint-green, sakura-pink, mango-orange, etc.
Specifications
Meteor65 (2022)
Item: Meteor65 1S Brushless Whoop (2022)
Weight: 22.83g (without battery)
FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G)
Frame: Meteor65 65mm 1S Brushless Frame
Motors: 0802SE 19500KV Motor
Props: 31mm 3-blade props (1.0mm Shaft)
Tilt: 30° (default)/20° (optional)
Camera: C03 FPV Camera
VTX: M03 25-350mW VTX
Canopy: Canopy for Micro Camera 2022 version
Battery: BT2.0 300mah 1S Battery
Flight time: 4 mins
F4 1S 5A FC (2022) AIO
CPU: STM32F411CEU6 (100MHZ)
Gyro: Six-Axis BMI270
Built-in Receiver: Serial ExpressLRS 2.4G
Receiver antenna: Line antenna
FC Size: 30x30mm
Mounting Hole Size: 26x26mm
Firmware version: betaflight_4.3.0_BETAFPVF411 (ELRS)
OSD: Built-in BetaFlight OSD
Blackbox: 8MB
Power Cable: 55mm, with BT2.0 connector
Weight: 3.6g(ELRS) without power cable and BT2.0 connector
ESC
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
ESC firmware: A_X_5_.HEX for Bluejay BB51 hardware
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Includes
1x Meteor65 Brushless Whoop Quadcopter (2022)
2x 300mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x Type-C USB cable
1x Customized Carry Case
1x Spare 31mm 3-blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera
Download the FC firmware and CLI dump file for Meteor65 ELRS2.4G
Pre-Orders shipping ASAP!!
All products with batteries must be shipped by a ground shipping method.
Want a 1S whoop for outdoor, around the house and yard? The Meteor75 Brushless Whoop Quadcopter would be your best choice! This whoop quadcopter is equipped with the ultralight F4 1S 5A FC (2022), supporting serial ExpressLRS 2.4G, Frsky, or TBS RX for options. The new canopy with special style and high-quality C03 FPV camera combined with 0802SE 19500KV motors make it perfectly balanced in all areas of performance.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features
The Meteor75 is the first generation whoop powered by a brand-new BT2.0 connector 450mAh battery. The BT2.0 connector effectively decreases internal connector resistance for a much better discharge performance compared with the initial PH2.0 connector.
The power system uses the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots a stronger experience of a powerful indoor and outdoor flight
Built-in 1.52g ultralight weight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones.
Adopted with an injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserved two UART ports on F4 1S 5A FC (SPI Frsky) board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
F4 1S 5A FC (Serial ELRS 2.4G) is flexible in upgrading and has great potential. It supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware.
The various colors of the spare parts including the 75mm frame and micro canopy, offer pilots more choices. Using them with BETAFPV waterslide decals, pilots can easily DIY and build their unique whoop drones.
BETAFPV Meteor Series
This is the new Meteor75 Analog VTX version with a new micro canopy, built-in serial ExpressLRS 2.4G instead of SPI ERLS 2.4G, and the new C03 FPV camera that ensures a high-quality and clear image. For pilots who want to fly 1S HD whoop drone, Meteor75 HD digital VTX is a good choice.
Meteor75 (2022)
Meteor75 (2021)
Meteor75 1S HD
FC&ESC
F4 1S 5A FC (2022)
F4 1S 5A FC
F4 1S 5A FC (2022)
RX
Serial ELRS, SPI FrSky/PNP, TBS
SPI ELRS, SPI FrSky, TBS
Serial ELRS, SPI FrSky/PNP, TBS
Camera
C03 FPV Camera
C02 FPV Camera
Walksnail/HDZero Camera
VTX
M03 Analog VTX
M03 Analog VTX
Walksnail Avatar or HD Zero Lite
Motors
0802SE 19500Kv Motor
1102 18000Kv or 0802SE 19500Kv Motors
1102 18000Kv Motors
Props
40mm 2-blade
40mm 3-blade, or 40mm 2-blade
40mm 3-blade
Canopy
New Micro Canopy (2022)
Micro Canopy
Micro Canopy for HD
Tilt
20° or 30°
30°
0-45°
Flight Time
6 mins (stable flying)
3-4 mins
3.5 mins (HDZero) or 3 mins (Walksnail)
BETAFPV upgraded all Meteor Series quadcopters like Meteor65, Meteor65 Pro, Meteor 75, and Meteor85 whoop quadcopters, through the new flight controller, motors, camera, frame, canopy, etc, to provide the best whoop quadcopters for pilots.
BT2.0 Connector
BETAFPV exclusive designed BT2.0 connector has broken through the bottle-neck of the PH2.0 connector. There is a graph comparing between BT2.0 connector 1S 450mAh battery and the Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has a long time and improvement in voltage sag with a BT2.0 connector, which brings better flight performance.
Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP and can be switched to Futaba SFHSS protocol through Betaflight configurator. The ESC on the new board powered by BB51 hardware in place of BB21 comes with Bluejay 96k ESC firmware, allowing 0802SE 19500KV motors to give full play to the efficiency of power. We update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75 (ELRS)
Meteor75 (FrSky, PNP, TBS)
FC Inside
F4 1S 5A FC (Serial ELRS 2.4GHz)
F4 1S 5A FC (SPI FrSky)
Gyro
BMI270
BMI270
FC Firmware
BETAFPVF411
BETAFPVF411RX
UART Port
One UART Port
Two UART Port
External RX
Not Supported
Supported
Note: For F4 1S 5A FC (serial ELRS 2.4G), ONLY Betaflight firmware 4.3.0 and up start to support BMI270 gyro. For F4 1S 5A FC (SPI Frsky), we recommend using BETAFPVF411RX 4.2.11 firmware and CLI dump file offered by BETAFPV. If you update the 4.3.0 and up firmware for serial ELRS 2.4G from the Betaflight official site, please flash the CLI dump file for Meteor75.
Download the FC firmware and CLI dump file for Meteor 75 ELRS2.4G, Frsky, or TBS.
C03 Camera
C03 FPV Micro Camera is 1.52g ultralight weight and a great camera for indoor micro FPV quadcopters. It features a 1200TVL definition with 1/3" CMOS sensor, 2.1mm lens for 160° FOV, and excellent latency, which boasts high-quality, clear and sharper images through your goggles.
Motors
0802SE 19500KV Motor motor is a lightweight 1S motor, compared with the 0802 series brushless motors, it is not only significantly reduced the weight which is only 1.88g/pc but also ensures excellent performance of power and thrust. It makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time.
Frame
This frame is ultralight only 5.68g and durable enough. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery. BETAFPV offers various colors of Meteor75 frames for options, making DIY easier.
Specification
Item: Meteor75 Brushless Whoop Quadcopter (2022)
FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G)/F4 1S 5A FC (SPI Frsky)
Frame: Meteor75 Frame
Motors: 0802SE 19500KV Motor
Props: 40mm 2-Blade Propellers (1.0mm Shaft)
Camera: C03 FPV Camera
Tilt: 30° (default)/20° (optional)
Canopy: Canopy for Micro Camera 2022 version
Receiver Option: ELRS2.4G, Frsky/PNP, TBS Crossfire
VTX: M03 25-350mW VTX
Battery: BT2.0 450mAh 1S 30C Battery
Flight time: 6 mins (stable flying) / 4.5 mins (acro flying)
Weight: 24.98g
Includes
1x Meteor75 Brushless Whoop Quadcopter (1S)
2x 450mAh 1S 30C Battery with BT2.0 connector
1x BT2.0 Battery Charger and Voltage Tester
1x TypeC USB cable
1x Customized Carry Case
1x Spare 40mm 2-Blade props (1.0mm Shaft)
1x Screwdriver
3x Decorative Parts
1x 20° Lens Camera Mount for C03 Camera
1x 30° Lens Camera Mount for C02 Camera
FAQ
Download the FC firmware and CLI dump file for Meteor75.
ExpressLRS is the most popular radio link in 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.