We have expanded our line of building supplies with the addition of a variety of 0.8mm heat shrinks. Good for protecting those smaller wiring connections.
Check out all our tools and building supplies!
Specifications
Outer Diameter: 0.8mm
Temperature Rating: 125 C
Voltage Rating: 600V
Includes
1x 0.8mm Heat Shrink Tubing by the foot
Due to this item’s size or weight, it is not available for free shipping and may be shipped via UPS Ground.
These 1 meter (39.37") pultruded Carbon Fiber rods are great for reinforcing models. Use them in the wings, fuselage, or other parts of the model.
Be sure to choose the dimensions right for you.
We carry Rods, Strips, Tubes and Square Tubes!
Includes
1x 1 Meter Carbon Fiber Rod - Choose Your Size
Due to this item’s size or weight, it is not available for free shipping and may be shipped via UPS Ground.
These 1 meter (39.37") pultruded Carbon Fiber Square/Square Tubes are great for reinforcing models. Use them in the wings, fuselage, or other parts of the model.
Be sure to choose the dimensions right for you.(Outer Dimensions x Thickness x Length)
We carry Rods, Strips, Tubes and Square Tubes!
Includes
1x 1 Meter Carbon Fiber Square Tubes - Choose Your Size
Due to this item’s size or weight, it is not available for free shipping and may be shipped via UPS Ground.
These 1 meter (39.37") pultruded Carbon Fiber strips are great for reinforcing models. Use them in the wings, fuselage, or other parts of the model.
Be sure to choose the dimensions right for you.We carry Rods, Strips, Tubes and Square Tubes!
Includes
1x 1 Meter Carbon Fiber Strip - Choose Your Size
Due to this item’s size or weight, it is not available for free shipping and may be shipped via UPS Ground.
These 1 meter (39.37") pultruded Carbon Fiber Tubes are great for reinforcing models. Use them in the wings, fuselage, or other parts of the model.
Be sure to choose the dimensions right for you.(Outer Diameter x Thickness x Length)
We carry Rods, Strips, Tubes and Square Tubes!
Includes
1x 1 Meter Carbon Fiber Tube - Choose Your Size
This a great two in one tool that gives a loud alarm at low voltage and can quickly display battery voltage. Simply plug a 1-8s battery's balance connector into the voltage meter/buzzer, and you will receive an instant readout of the total voltage and an individual reading of each cell. Don't be caught without this battery checker!
Tip: If the buzzers are too loud for you, fill them with a little hot glue to mute it!
Check out our other Battery Chargers and Accessories!
Specifications
Compatible with 1-8S Lipo/Li-ion/LiMn/Li-Fe batteries
Voltage detection precision: +/-0.01V
Low voltage alarm mode for 2S~8S; Adjustable alarm set value range:~2.7~3.8V
Total voltage display range: 0.5V~36V
Includes
1x 1-8S LiPo Battery Checker Voltage Tester w/ Low Voltage Alarm
Spare / replacement heavy gauge XT30 pigtail with capacitor.
We also carry a 20AWG version.
Check out the rest of our pigtails & connectors!
Specifications
Dimensions: 16AWG x 70mm (80mm Overall)
Capacitor: 16V 100uF
Weight: 4.5g
Includes
1x 16AWG XT30 Pigtail w/ Capacitor
7.4V nominal voltage for use with existing Fat Shark goggles and fits into head strap like standard Fat Shark battery packs. Large capacity when used with high capacity cells (batteries not included).
Batteries should be removed and charged via a dedicated 18650 style charger.
Check out RDQ's goggle battery here.
Check out our Lithium Ion Cells & Chargers all our FPV Goggles and Accessories!
Includes
1x 18650 Li-Ion Battery Case for FatShark Goggles
This product is the checker only. It does not include cables.
This battery checker takes the guesswork out of wondering what levels your Whoop Batteries are at! A much needed accessory for any FPV pilot.
Check out our other 1S Battery Chargers and Accessories!
Features
Accepts both types of the plugs 2.0 JST female and 1.25 JST female
Battery voltage detection, reverse connection protection.
Does not check HV batteries - only normal 3.7v
Includes
1x 1S LiPo Whoop Battery Checker - PH2.0 and JST 1.25
This LED strip is 6.5" long and contains 24 addressable LEDs. High quality LEDs put on a quality strip means that your quad will look very good for a long time to come! The strip can be cut into any length you desire. Here at RDQ, we like to cut this into 4x 6 LED strips and put them under each arm of the quad.
Check out all our LEDs!
Specifications
Input voltage: 5V
Length: 6.5"
Includes
1x 24 LED Strip - 5V High Density LEDs for FPV Racing
Dont toss your battery just because the balance leads got chewed up in your props!
Repair the balance leads on your 2S batteries!
Note: Please check the colors of the wires and their respective polarities before connecting to your device.
Check out the rest of our Tools & Building Supplies!
Specifications
Material: 22 AWG Silicon Wire
Diameter (OD): 1.5mm
Conductor: Tinned Copper
Insulation: Silicone Rubber
Diameter of single metal wire / quantity: 0.08mm / 30
Length of wire: approx. 16cm / 6.26 inch
Includes
10x 2S1P JST Connector Male Plug with Wire
10x 2S1P JST Connector Female Plug
Portable lightweight handheld electric hot air gun perfect for your heat shrink tubing!
Check out our ever growing selection of tools and building supplies!
Features
The nozzle can reach 200°C/392°F in seconds.
Made of high quality stainless steel inside and ABS plastic outside.
Vents in both sides of the tail to reduce internal temps and extend lifespan.
Built in folding rest
Two pin US plug and 1m / 3ft cable
Even a great substitute for your toaster oven!
Includes
1x Portable Mini Heatgun
Desoldering wick is a copper braid used in the rework and repair of printed circuit boards, computers, cell phones or other electronics. Desoldering wick lets you easily remove the extra solder from components or pads on the circuit board. Just press the braid onto the connection with a hot iron and the solder wicks up into the braid.
Check out all our soldering equipment and tools & building supplies !
Specifications
Oxygen free copper
Length: 1.5m
Width: 3mm
Includes
1x Solder Wick - 1.5m
Dont toss your battery just because the balance leads got chewed up in your props!
Repair the balance leads on your 3S batteries!
Note: Please check the colors of the wires and their respective polarities before connecting to your device.
Check out the rest of our Tools & Building Supplies!
Features
For IMAX B6 or Battery test.
3 cell 11.1V Lipo battery balance charger plug.
For Vehicle Type: Multirotor, Airplane, Helicopter.
Specifications
Material: 22 AWG Silicon Wire
Diameter (OD): 1.5mm
Conductor: Tinned Copper
Insulation: Silicone Rubber
Length of wire: approx. 16cm / 6.26 inch
Diameter of Single Metal wire/Quantity: 0.08mm/30
Includes
10x 3S1P JST Connector Male Plug with Wire
10x 3S1P JST Connector Female Plug
Check out this bundle of BEAST motors from NewBeeDrone, where you can grab 4 motors for the price of 69.99 dollars. You get 4 NewBeeDrone Flow 2207 2050Kv brushless race motors with this bundled deal. These motors are perfect for 6S builds and those who want that MONSTER power with a clean metal polish aesthetic. Deck out any quad with these motors, as they fit all styles of quads!
Check out our vast brushless motors selection, and all our NewBeeDrone products!
Specifications
Input Voltage: 6S
Shaft Size: 5mm
Weight: 33.3g
Mounting Pattern: 16x16mm M3
Includes
1x NewBeeDrone Flow 2207 2050Kv Brushless Race Motor - Choose Your Version
1x Hardware Set
RX antenna tube holders compatible with both the normal and knurled standoffs.
The antenna tubes are at a 45 degree angle and come in sets of 2.
Works perfect with the Forever Antenna Tubes.
RX antenna tube holders compatible with both the normal and knurled standoffs.
The antenna tubes are at a 45 degree angle and come in sets of 2.
Works perfect with the Forever Antenna Tubes.
Dont toss your battery just because the balance leads got chewed up in your props!
Repair the balance leads on your 4S batteries!
Note: Please check the colors of the wires and their respective polarities before connecting to your device.
Check out the rest of our Tools & Building Supplies!
Features
For IMAX B6 or Battery test.
4 cell 14.8V Lipo battery balance charger plug.
Specifications
Material: 26 AWG Silicon Wire
Diameter (OD): 1.5mm
Conductor: Tinned Copper
Insulation: Silicone Rubber
Length of wire: approx. 15cm / 5.9 inch
Diameter of Single Metal wire/Quantity: 0.08mm/30
Includes
10x 4S1P JST Connector Male Plug with Wire
10x 4S1P JST Connector Female Plug
Dont toss your battery just because the balance leads got chewed up in your props!
Repair the balance leads on your 5S batteries!
Note: Please check the colors of the wires and their respective polarities before connecting to your device.
Check out the rest of our Tools & Building Supplies!
Features
For IMAX B6 or Battery test.
5 cell 18.5V Lipo battery balance charger plug.
For Vehicle Type: Multirotor, Airplane, Helicopter.
Specifications
Material: 26 AWG Silicon Wire
Diameter (OD): 1.5mm
Conductor: Tinned Copper
Insulation: Silicone Rubber
Length of wire: approx. 15cm / 5.9 inch
Diameter of Single Metal wire/Quantity: 0.08mm/30
Includes
10x 5S1P JST Connector Male Plug with Wire
10x 5S1P JST Connector Female Plug
Dont toss your battery just because the balance leads got chewed up in your props!
Repair the balance leads on your 6S batteries!
Note: Please check the colors of the wires and their respective polarities before connecting to your device.
Check out the rest of our Tools & Building Supplies!
Features
For IMAX B6 or Battery test.
6 cell 22.2V Lipo battery balance charger plug.
For Vehicle Type: Multirotor, Airplane, Helicopter.
Specifications
Material: 26 AWG Silicon Wire
Diameter (OD): 1.5mm
Conductor: Tinned Copper
Insulation: Silicone Rubber
Length of wire: approx. 15cm / 5.9 inch
Diameter of Single Metal wire/Quantity: 0.08mm/30
Includes
10x 6S1P JST Connector Male Plug with Wire
10x 6S1P JST Connector Female Plug
This is that adhesive backed fabric tape you've probably seen holding motor wires on lots of pre-built micros. It's super handy stuff and its matte finish makes for a cleaner looking build than zip ties or electrical tape. We offer it in 2ft strips that are easily enough to fasten the motor wires of a couple 5" builds, and several more micros.
Check out all our tools and building supplies!
Includes
2ft 8mm Fabric Tape
Set of 5 simple adjustable pushrod linkages available for three rod sizes.
Check out the rest of our servos, linkages & accessories and all our tools & building supplies!
Includes
5x Adjustable Servo Pushrod Linkage
The Aikon flight controller is a new generation flight controller and ESC combination specifically designed for cinewhoops and other high-current applications. We've packed all the greatest features into one seamless flight experience.
Check out our other AIO flight controllers and the rest of our Aikon gear!
Features
216mhz F7 processor
Independent FC and ESC PCBs for low noise
5 Software invertible hardware UARTS
Onboard OSD and BlackBox
Software-controlled VTX power switch (assigned to USER1 mode by default)
Connectors for DJI-HD and RC link
LED and buzzer outputs (LED pad doubles as PPM)
On-board high overhead voltage regulators rated up to 6S (50v peak to handle voltage spikes)
10v 1.5A voltage regulator for DJI HD system
3.3mm high current MOSFETs.
Specifications
Battery: 3-6S
Mounting Holes: 25.5x25.5mm
FC Firmware: Betaflight AIKONF7 Target
MCU: STM32F722
IMU: MPU6000
Barometer: DSP310
Blackbox: SPI 16MB
ESC Firmware: BLHeli_32
Constant Current: 45A
Burst Current: 55A
Current Sensor Scale: 200
Weight: 14.5g
Includes
1x Aikon F7 Mini 25x25 AIO Flight Controller w/ 45A 32bit ESC
The Aikon AK32 Pro II continues Aikon's pursuit of excellence! This ESC combines the latest forward-looking capabilities with top of the line reliability.
Make sure to check out our other ESCs and entire line of Aikon gear!
Specifications
Input Voltage: 2-6S
MCU: AT32F421
Max Continuous Current: 50A
Max Burst Current: 65A
Firmware: BLHeli32
Bootloader: Yes
Mounting Pattern: 20x20mm
Weight: 13.8g
Includes
1x Aikon AK32PRO II 32bit 50A 2-6S 20x20 4in1 ESC
This FC pairs seamlessly with any Aikon ESC. The F7 MCU will allow you to dial in your tune the way you want it and the DJI plug and play means it's ready to go with the Air Unit or Vista.
Check out all our 20x20 FCs, our DJI compatible gear section, and all our Aikon gear!
Features
216mhz F7 processor
5 Software invertable hardware UARTS
Onboard OSD and blackbox
Software controlled VTX power switch
LED outputs
Quick connection cable for 4-in-1 ESCs
On-board high overhead voltage regulators up to 6S (50v peak for voltage spikes)
10V/1.5A regulator for DJI HD system
DJI Quick Connect Port
Specifications
Input Voltage: 2-6s
Mount Hole: 20x20mm
Betaflight Target: AIKONF7
MCU: STM32F722RET6
IMU: BMI270
Blackbox SPI: 16MB
Weight: 8g
Includes
1x Aikon F7 Mini V3 HD 20x20 Flight Controller for DJI
Wiring Diagram
Can be used with any 8 pin stacks, just make sure to re-pin when necessary!
Specifications
Length: 72mm end to end
Includes
1x Airbot 4in1 ESC to Flight Controller 8 Pin Cable Replacement for Bardwell & Ori32
The G4 features Betaflight compatibility and is the first of its kind. It contains 4 35A AM32 ESCs, 6S max and the QF32MTF4AK8U7 on the AIO board, creating a more compact design. Two voltage regulators – a 5V and 10V, both rated for 2.5A – are included. The 10V one can power the VTX & DJI O3 Air Unit, while the 5V one can power the LEDs, peripherals, etc. The STM32G47X MCU, ICM-42688p gyro, 16MB Data Flash, DSP310 baro, 16 RGB LEDs, and plug solutions for digital video complete the package.
A new feature is the ultra-hydrophobic nano waterproof coating. This coating allows air to pass through while avoiding water, giving extra protection from moisture and other elements.
Important note: When trying to get the HD OSD working, it's required that both ground pins out of the DJI port are not soldered to the VTX.
Check out our other AIO flight controllers, as well as the rest of our Airbot selection!
Features
Superhydrophobic Nano Waterproof Coating
Onboard 16 RGB LEDs can be programmed
ESC has a F4 MCU, runs AM32 firmware, capable of 6S and is rated at 35Amps
10V BEC for DJI O3 Air Unit
Specifications
MCU: STM32G473, 512KB Flash
BEC: 5V 2.5A + 10V 2.5A
Blackbox: 128Mbit, 16MB
Gyro: ICM-42688
Barometer: DSP310
ESC: F4 MCU, run AM32 firmware, 6S 35Amps
OSD: AT7456
4x Uarts
1x 12C
Weight:10.4g
Mounting pattern：25.5x25.5mm
Connector Pinout:
SDA, SCL, DN, DP, GND, 5V, L-RX1, L-TX1 is for External USB/GPS Connector
TX2, GND, RX1, TX1, GND, 10V is for VTX Connector
Wiring Diagram
- Information was referenced from a review of the Airbot Fenix G4 AIO board brought to you by VitroidFPV.
The Airbot OpenLager gives the capability of black box recording to any drone that doesn't have it. This is fantastic for tuning and finding issues in your system.
This device needs to be flashed with updated firmware before use. Follow the simple instructions in the wiring & info tab.
Check out our other flight controller accessories, as well as the rest of our Airbot selection!
Features
It's faster than an average black box with a 4 bit SD interface clocked at 19.2MHz with DMA.
It has buffer memory to ride out times when the SD card is busy (125kbytes with the current firmware)
It fits in a smaller form factor builds with ease.
ESD protection on input pins.
And it has a flip-up microSD connector that is better at retaining the card in crashes and hard landings.
Specifications
Dimensions: 20x15mm
Weight: 2g
Includes
1x Airbot OpenLager Blackbox
Wiring & Info
The OpenLager is easy to use with async serial. First, wire according to the diagram below (an example of an OpenPilot-style connector is in the drawing). Note that you should attach the flight board's TX to Openlager's RX pin!
OpenLager has an onboard regulator and can be powered with 3.3-5.5V (the regulator dropout voltage is low enough that the SD card will still work properly at 3.3V input).SD CARD MUST BE FAT16 OR FAT32 FORMAT. FIRMWARE MUST BE UPDATED BEFORE USING:
Format your SD card. It must be either FAT or FAT32 format (SanDisk Extreme Pro 8GB recommended)
Put the firmware lager.bin file into the sdcard and insert into the OpenLager
Power on. The RED led should blink for several seconds. Wait until the RED led is stops blinking and continue to wait 10s more.
Power off
Format the SD card again
Insert the SD card into OpenLager and power on.
Power off; remove the card, and attach it to your computer. You'll find openLager has written a file to it called lager.cfg:
{ "startupMorse" : "", "useSPI" : false, "baudRate" : 2000000, "preallocBytes" : 104857600, "preallocGrow" : false}
The important field to change is baudRate -- set it to the speed of the serial you'll be using for logging. dRonin supports 115200, 250000, 1500000, 2000000, and 2470000 bits per second. Cleanflight prefers 250000 bits per second, etc.
The green LED is on always when power is applied, and the red LED blinks with activity when the card is writing. After 200ms of inactivity, the buffers on openLager will be forcibly flushed. If power is suddenly removed, the file may not be completed in the filesystem; this can be changed by setting preallocGrow to 'true' at the possible cost of garbage being present at the end of the file in this scenario.
The firmware for openlager may be updated by putting an appropriate firmware image called lager.bin on the card.
Featuring a whoop camera with Smart Audio! Take your Whoop tech to the next level.
Check out all our Camera/VTX AIOs & Combos
Features
Super light weight: 4.3g, all in one vtx + camera + antenna
One button frequency and power setup
Support 0.01mW parameter-adjusting mode
0.01/25mW/50mW/100mW/200mW power switchable
OSD configuration using FC Uart (F3/F4/F7 with OSD)
Notice: 5645,5925,5945(E4,E7,E8) channels are not available due to FCC regulation.
Specifications
Input voltage: 3.2-5.5V
Weight: 4.3g(exclude antenna)
Frequency: 5.8GHz 5 bands 40 channels
Includes
1x AKK AIO-SA Whoop/Micro AIO FPV Camera & 25-200mW VTX w/ Smart Audio
The AKK FX3 Ultimate is essentially the mini version of the AKK FX2. With a 20x20 profile, it can easily fit into any of your 20x20 builds while having a high max output power and Smart Audio capability.
Details:
Support Pit Mode
25mW, 200mW, 400mW and 600mW power switchable
One button frequency and power setup
OSD configuration using Smart audio
7-24V input with 5V output
MMCX+UFL connector
MIC
Note: Smart Audio is not compatible with KISS flight controllers.
FPV REGULATORY NOTICE
The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. RDQ cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.
in AKK's newest VTX which has built-in DVR, Smart Audio, up to 6s (7 - 26v) direct Lipo input, adjustable power output (25, 200, 600 & 1000 mW) w/ pit mode, and a 5v cam power output.
Check out the rest of our selection of VTX's!
Specifications
Brand name: AKK
Item name: Infinite DVR VTX
Input voltage: 7V to 26V
Extra features: Smart audio DVR
Power supply: 5V output for camera
Output power: 25/200/600mW/1000mW
Antenna connector: MMCX
Cable connector: Solder pads
Records Video Size: VGA (640*480)
Max Support TF Card: 32G
Dimension: 36x36mm, 30.5 stackable hole
Weight: 8.8g (excluding antenna)
Features
Support Smart audio
25/200/600/1000mW power switchable
One button frequency and power setupOSD configuration using smart audio
7-26V input with 5V output for camera
With MIC
Notice: 5645/5925/5945 (E4/E7/E8) are not available due to FCC regulation. Selecting 5645/5925/5945 (E4/E7/E8) will be invalid action.
Note: 37 channels are all above 5650 and below 5925MHz, which are legal to use in the USA with an amateur radio license.
This equipment is being sold under FCC’s amateur radio rules.
Operators must require amateur radio license to operator legally in
the US. Use of amateur equipment without a license or use of
equipment on restricted frequencies could subject the operator to
significant fines by the FCC.By purchasing this equipment, the user is
agreeing that they understand these responsibilities and will operate
the equipment legally. More information related to ARL, please go to
http://www.arrl.org/getting-licensed.Pacakge Included:
1x VTX
1x pigtail
1x cable
FPV REGULATORY NOTICE
The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. RDQ cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.
This is a great and quick "solder n' go" product if you need a capacitor for your quad. The capacitor and pigtail come pre-soldered together and all you need to do is solder the 14 AWG leads to your quad.
Check out our other tools and building supplies and all our Capacitors!
Specifications
Wire: 14 AWG
Wire Length: 100MM(measured from pcb)
Capacitor: 25V 2200uF, 35V 1000uF, 35V 2200uF
Connector: Yellow XT60
Weight: 13-17g
Includes
1x All-in-One Capacitor and XT60 Pigtail Combo
Typically used to connect a device with female a XT60 plug to a DC power supply, lead acid, SLA, or Pb field battery using Alligator clips.
Check out our selection of chargers and accessories and our pigtails and adapters!
Specifications
Wire Gauge: 14 AWG
Length: 250mm (10")
Includes
1x Alligator Clips to XT60 Male Adapter Cable
This socket mount will hold a male XT60 securely against carbon meaning you now have more options for safely mounting your power leads! The mounting hole distance is 20mmMale XT60 Not Included.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Specifications
Mounting Pattern: 20mm, M2.5
Includes
1x Aluminum XT60 Surface Mount Bracket
2x M2.5 Screw
These handy little connectors are basically 3 pin XT30s, They can be used on ESCs, motors, or anything with 3 wires to allow for quick connections and part swaps.
Check out all our pigtails, adapters and connectors!
Features
Suitable for connecting ESCs and motors
With protective sleeve
Assistive weld foot, more stable
Specifications
Body Material and Surface Plating: Brass and gold plated
Insulation Material: PA66
Original Internal Resistance: 0.8MΩ
500 Times Internal Resistance: 0.85MΩ
Max. Continuous Current: 30A (within 30 minitues)
Max. Instantaneous Current: 40A (within 1 minitues)
Recommended Cable Spec: 18AWG 2.8mm diameter
Recommended Soldering Spec: 400° C/3S
Weight: 1.2g/pcs
Insulation Degree: UL94V-0
Machine Life: 3000 Times
Includes
1x AMASS MR30 Connector Male w/ Protective Shield
1x AMASS MR30 Connector Female w/ Protective Shield
These handy little connectors are basically 3 pin XT60s, They can be used on ESCs, motors, or anything with 3 wires to allow for quick connections and part swaps.
Check out all our pigtails, adapters and connectors!
Features
Suitable for connecting ESCs and motors
With protective sleeve
Assistive weld foot, more stable
Specifications
Body Material and Surface Plating: Brass and gold plated
Includes
1x AMASS MR60 Connector Male w/ Protective Shield
1x AMASS MR60 Connector Female w/ Protective Shield
These handy little connectors are basically 3 pin XT60s, They can be used on ESCs, motors, or anything with 3 wires to allow for quick connections and part swaps.
Check out all our pigtails, adapters and connectors!
Features
Suitable for connecting ESCs and motors
With protective sleeve
Assistive weld foot, more stable
Specifications
Body Material and Surface Plating: Brass and gold plated
Includes
1x AMASS MT30 Connector Male w/ Protective Shield
1x AMASS MT30 Connector Female w/ Protective Shield
These XT150 connector sets are ideal for large batteries, ESC, or motors! The durable nylon material is less likely to experience damage than other connectors and works well with up to 150 amps of current.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Features
Nylon material holds 150A current for extended periods without exceeding 80 Degrees.
Male connectors use a collet-style spliced contact area.
Dovetail linking.
Easy to solder.
Specifications
Max Amps: 150
Diameter: 6mm
Connection Type: Male or Female
Includes
1x AMASS XT150 w/ 6mm Gold Connector - Choose Version & Color
This genuine Amass connector is an ideal option for safely and securely mounting your power leads. Amass is known for their quality and there is no exception with this connector.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Specifications
Plating: Brass and Gold
Mounting Pattern: 20mm, M2.5
Includes
1x Amass XT60E1 Male
Premium Amass XT60H connector for when the classic XT60 just won't cut it. The snap on cover for the wire side of the connector means no need for heat shrink.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Includes
1x Amass XT60H Connector - Male or Female
These genuine Amass XT90H connectors are perfect for those that like to go big with their builds. If you need a connector that can to handle a lot of current, the XT90 will do the job with ease!
Choose male or female, and your color preference!
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Specifications
Plating: Brass and Gold
Includes
1x Amass XT90 H Connector
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1750
Input Voltage: 4-6S
Motor Height: 16.5mm
Stator Dimensions: Φ22x7mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 28.1g
Includes
1x AMAX Performante A-Bell 2207 1750Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 2550
Input Voltage: 3-4S
Motor Height: 16.5mm
Stator Dimensions: Φ22x7mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 28.1g
Includes
1x AMAX Performante A-Bell 2207 2550Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1750
Input Voltage: 4-6S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 1750Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1950
Input Voltage: 4-6S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 1950Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 2550
Input Voltage: 3-4S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 2550Kv Motor
