This a great two in one tool that gives a loud alarm at low voltage and can quickly display battery voltage. Simply plug a 1-8s battery's balance connector into the voltage meter/buzzer, and you will receive an instant readout of the total voltage and an individual reading of each cell. Don't be caught without this battery checker!
Tip: If the buzzers are too loud for you, fill them with a little hot glue to mute it!
Check out our other Battery Chargers and Accessories!
Specifications
Compatible with 1-8S Lipo/Li-ion/LiMn/Li-Fe batteries
Voltage detection precision: +/-0.01V
Low voltage alarm mode for 2S~8S; Adjustable alarm set value range:~2.7~3.8V
Total voltage display range: 0.5V~36V
Includes
1x 1-8S LiPo Battery Checker Voltage Tester w/ Low Voltage Alarm
Dont toss your battery just because the balance leads got chewed up in your props!
Repair the balance leads on your 2S batteries!
Note: Please check the colors of the wires and their respective polarities before connecting to your device.
Check out the rest of our Tools & Building Supplies!
Specifications
Material: 22 AWG Silicon Wire
Diameter (OD): 1.5mm
Conductor: Tinned Copper
Insulation: Silicone Rubber
Diameter of single metal wire / quantity: 0.08mm / 30
Length of wire: approx. 16cm / 6.26 inch
Includes
10x 2S1P JST Connector Male Plug with Wire
10x 2S1P JST Connector Female Plug
Revised version now includes a power switch and additional solder pads.The Analog FPV FatShark Module Adapter V2 for DJI Digital FPV Goggles fits so well you can use a fat shark or various third-party fat shark style analog video receivers modules! It transfers video and audio signals to the high-quality screen of DJI FPV goggles for viewing or recording. This compact and lightweight adapter is easy to install and won't void your warranty! Check out all our DJI compatible frames, electronics & accessories and our FPV receiver modules & antennas collection!Specifications
Input Voltage: 2S-4S (DC5.5x2.1mm)
Internal Voltage: 5V 3A (with pad output)
Output Voltage: 2S-4S (DC 5.5x2.1mm)
Signal Input: Standard Fat Shark Receiver Port
Including third-party receivers: Realacc, Furious, etc.
Signal output: standard audio / video
Power Switch
Dimension: 48x28x12mm
Weight: 10g (without extension cable)
Includes
1x Analog FPV Adapter for DJI Goggles
1x Adapter mounting board and screws
1x Audio and video cable
1x Power cable
Wiring Diagram
V3 now includes a voltage display, power switch and additional solder pads.This analog fat shark module adapter fits on the side of your DJI Digital FPV Goggles so you can use a fat shark or various third-party fat shark style analog video receivers modules! It transfers video and audio signals to the high-quality screen of DJI FPV goggles for viewing or recording. This compact and lightweight adapter is easy to install and won't void your warranty! We also have the V2 Adapter if you don't need the voltage display. Seen below installed in the Aluminum Case we carry specifically for this device:Check out all our DJI compatible frames, electronics & accessories and our FPV receiver modules & antennas collection!
Specifications
Input Voltage: 2S-4S (DC5.5x2.1mm)
Internal Voltage: 5V 3A (with pad output)
Output Voltage: 2S-4S (DC 5.5x2.1mm)
Signal Input: Standard Fat Shark Receiver Port
Including third-party receivers: Realacc, Furious, etc.
Signal output: standard audio / video
Dimension: 55x28x12mm
Weight: 13g (without extension cable)
Includes
1x Analog FPV Adapter V3 for DJI Goggles
1x Adapter mounting board and screws
1x Audio and video cable
1x Power cable
1x Allen Key
Wiring Diagram
This new strap can be used on a 2s, 1600mAh battery all the way up to a 4s, 3000 mAh battery. It fits all Armattan models. It is coated with rubber so that your battery will not slip out of place easily. Now with a metal buckle for extra strength.
Check out the rest of our battery straps and all our Armattan products!
Includes
1x Armattan Anti-Slip Battery Strap
ASC758, Reedy WolfPack 2S Hard Case Shorty 30C LiPo Battery (7.4V/3000mAh) w/T-Style Connector
The Reedy WolfPack 2S Hard Case Shorty 30C LiPo Battery is well suited for Trail Trucks, Crawlers, and a variety of vehicle types that utilize a shorty battery configuration. Wires exit the case through a rubber gasket, which protects the wire's insulation while helping to prevent moisture from entering the case. High quality cell manufacturing and construction techniques result in reliable operation and maximum cycle life. Reedy's Wolfpack LiPo batteries come equipped with beefy silicone wires and a reliable, low-resistance T-plug connector. An integrated balance lead with XH connector is included.
Features:
Versatile shorty configuration
High capacity for extended run times
Generous discharge rating increases power and speed
Durable hard case for increased crash protection
Reliable operation and maximum cycle life
Low-resistance T-plug connector
Rubber gasket wire protection
Value priced
Specifications:
Capacity: 3000mAh
Voltage: 7.4 (2S)
Dimensions (mm): 95.7 x 46.8 x 24.7
Max. Charge Rate: 6.0A
Discharge Current: 30C/55C
Weight (g): 158
Connector: T-plug/12-gauge
This product was added to our catalog on March 16, 2021
All batteries must be shipped by a ground shipping method.
Auline has made a great addition to your Fatshark goggles. This battery features 2 21700 cells, perfect for powering your goggles for a long time. It even fits in your goggle strap for easy placement.
Check out our other 2S batteries, as well as the rest of our Auline selection!
Specifications
Nominal Voltage: 7.4V
Cells: 2S
Capacity: 4800mAH
Discharge Rate: 1C
Composition: Li-Ion
Discharge Lead: XT30 34.5mm
Balance Lead: JST-XH 37.5mm
Dimensions: 73x42x21mm
Weight: 158g
Includes
1x Auline 7.4V 2S 4800mAH 1C Li-Ion Battery for Fatshark Goggles - XT30
New V2 comes with a tactile power button, 6S support and a cable management kit! The plug and play Digidapter from British Drone Industries is the cleanest way to add analog FPV capabilities to your DJI Goggles. The injection molded face plate keeps your goggles looking sharp, and the included cables mean soldering is purely optional.
Check out all our FPV receiver modules and our DJI compatible gear!
Features
Short delay tactile power button for analog module
Compatible with existing modules: The Digidapter is compatible with existing analog modules. Featuring a standard 9 pin header for use with the TBS Fusion, Foxeer Wildfire, Rapid Fire, True D-X, Eachine Pro58, and more..
Plug & Play No Solder Solution: Installation takes less than a minute, and mounts quickly and easily to the front of your DJI Digital FPV Goggles. Including optional solder points for a cable free solution.
New cable management set included!
Specifications
Maximum Input Voltage: 28 Volts DC
Minimum Input Voltage: 7.4 Volts DC
Nominal Output Voltage: 5 Volts DC
Maximum Module Supply Current: 1 Amp
Rated Continuous Power: 5 Watts
Ports:
5.5mm x 2.1mm DC In 7.4v-26v (2s-6s)
4 pole 3.5mm video/audio out
9 pin RF module receiver header
Cables:
5.5mm x 2.1mm Male to Dual 5.5mm x 2.1mm Female DC Jack Splitter
4 Pole Gold Plated 3.5mm Male to 3.5mm Male Video Cable
Material/Color: Matte Black, Injection Molded, Acrylonitrile Butadiene Styrene
Dimensions: 158x74x40mm (6.25x3x1.6 inches)
Weight: 34g
Includes
1x Digidapter V2 faceplate
1x Analog video cable
1x Analog video/audio splitter for audio out
1x Dual DC/DC male to single DC female split cable
1x Allen key
2x 12mm cap head bolts
1x Cable strain relief clip
2x Cable clips
Lightest 1103 motors in the world. Only 3.2g with connector. This motor was made custom for the Beta75X 2S Whoop.
A 1.5mm header pins connector is include. So no soldering needed, just plug and play.
Check out our ever-growing selection of Whoop products!
Features
1103 11000KV brushless motors is customed for 2S brushless whoop drone.
Fit with 1735, 1935, 2030, 3020 propellers
Shaft Diameter: 1.5mm, Weight: 3.2g
Compatible with 2S lipo battery
Specifications
Height: 14mm
Weight: about 3.2g
Shaft: φ1.5mm
Motor Mount Holes: M1.6 on Dia 8.5mm
KV (rpm/V): 11000
Voltage: 7.4V, 2S Lipo battery
Plug: Micro JST-1.25 3-pins connector
Includes
4x BetaFPV 1103 11000Kv Micro/Whoop Motor
BETAFPV offers 2 versions of the 2S Battery Charger and Voltage Tester, each with different ports - BT3.0 and XH2.54 - capable of charging both LiHV 8.7V and LiPo 8.4V batteries. Not only does it have a digital display function, but it also features 2S battery voltage monitoring capabilities. Additionally, it supports PD3.0 fast charging protocol. This compact and portable charger is fully functional and user-friendly, and caters to the charging needs of 2S quadcopter enthusiasts, empowering them to recharge their batteries anytime, anywhere.
Check out our other charging accessories, as well as our range of BetaFPV gear!
Features
A compact and portable 2S Battery Charger and Voltage Tester with a digital display, specifically designed for the BT3.0 series of batteries.
It supports the PD3.0 fast charging protocol, offering higher power output and multiple charging options for a faster and safer charging experience with compatible devices.
Equipped with a digital display function and capable of monitoring battery voltage during charging.
With dual variants boasting BT3.0 and XH2.54 ports, this charger offers RC users different connection options.
Featuring a Type C interface instead of a USB interface, providing an even wider selection of charging options
Fulfilling the charging requirements of 2S batteries, this charger is a go-to choice for discerning enthusiasts.
XH2.54
This charger is compatible with 2S LiPo batteries(8.4V) and has an XH2.54 battery port. Please note that charging 2S LiHV batteries (8.7V) may result in undercharging. We recommend using a LiPo 2S battery with a corresponding balance connector available in the market. During the charging process, if the digital display shows a voltage exceeding 8.4V (e.g. 9V), please disconnect the power supply immediately and check if there is any issue with the battery or the charger.
BT3.0
This charger is designed to charge 2S LiHV batteries(8.7V) with a BT3.0 battery port. Please note that attempting to charge 2S LiPo batteries(8.4V) may pose a risk of overcharging. To ensure safe and optimal charging, we recommend using it with the BETAFPV BT3.0 450mAh 2S LiHV battery. During the charging process, if the digital display shows a voltage exceeding 8.7V (e.g. 9V), please disconnect the power supply immediately and check if there is any issue with the battery or the charger.
Specifications
Battery Type: BT3.0-LiHV(charging voltage:8.7V) / XH2.54-LiPo(charging voltage:8.4V)
Product Color: White(BT3.0) / Black(XH2.54)
Input Interface: Type-C USB
Input Voltage Range: 5-12V
Input Power: Maximum 15W
Maximum Input Current: 2.5A
Charging Protocol: PD3.0
Weight (per charger): 17.0±1.0g
Dimensions (L×W ×H): 61*25*17mm
Battery Capacity Display: LED Digital Display displays the total voltage and individual cell voltage of the
2S battery
LED Digital Display and Red LED indicate charging status:
Usage Notes
Please note the polarity markings on the device and do not connect the charger in reverse polarity.
The 2S Battery Charger and Voltage Tester only supports charging for 2S batteries, not 1S batteries.
The charger can only charge one battery at a time and is not designed for charging two or more batteries simultaneously.
Includes
1x BetaFPV 2S Battery Charger / Voltage Tester - Choose Your Version
Compared with the Beta75X frame, the Beta75X V2 frame only weighs 5.6g, It is lighter and the gravity center of the V2 frame is more concentrated. Increased the height of the frame loop, props can be completely wrapped by the protective ring. A better choice for a 75mm brushless whoop drone. What's more, the Beta75X V2 Frame is specially designed with two different motor mounting holes that support 1102 and 1103 brushless motors.
Check out all our whoop frames & accessories and all our BetaFPV gear!
Features
The Beta75X V2 frame only weighs 5.6g, it is lighter and the whole drone’s gravity center more concentrated than the Beta75X V1. Meanwhile, the motor mount position uses a quadrilateral stretch structure, makes the frame more durable and stable.
Increased the height of the frame loop, props are completely wrapped by the protective ring, more effectively protected the propellers.
Designed two different motor mounting holes that support 1102 and 1103 brushless motors at the same time.
With a 26mm*26mm FC mounting columns can match whoop style flight controllers like F4 AIO 12A FC. The battery slot fits BETAFPV 300mAh 2S and 300mAh 3S-S battery.
Specifications
Diagonal motor to motor distance: 75mm
Motor mounting hole: for both 3 and 4 hole motors
FC mounting hole: 26mm x 26mm, fully compatible with whoop style FC board mounting pattern
Battery slot size: 6.8x16.1mm
Material: Plastic
Weight: 5.6g
Includes
1x BetaFPV Beta75X V2 Whoop Frame - Choose Your Color
All batteries must be shipped by a ground shipping method.
Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Meanwhile, it supports the Betaflight configurator which is a popular application to configure RC aircraft.
Check out our other RTF combos, all our pre-built quads and our BetaFPV selection!
Features
An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system.
Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoor.
Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and 2xBT2.0 450mAh 1S 30C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight.
Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop & impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.
Specifications
Item: Cetus X Brushless Quadcopter
Weight: 55g
Wheelbase: 95mm
FC: F4 1S 12A FC V2.2 (ELRS 2.4G)
Motors: 1103 11000KV Motor
Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G
VTX: M04 25-400mW VTX
Battery: 2*BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins
Downloads
FC Firmware and ESC download
Includes
1 x Cetus X Brushless Quadcopter
1 x BT2.0 Battery Charger and Voltage Tester
2 x BT2.0 450mAh 1S 30C Battery
1 x Phillips Screwdriver
1 x Prop Removal Tool
1 x Type-C Adapter
4 x Gemfan 2020 4-Blades Props
All products with batteries must be shipped by a ground shipping method.
Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right powerful performance. BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate a bigger battery.
Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features
The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks.
It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.
Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better.
Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board.
The various colors of the spare parts including the Meteor75 Pro frame and Micro
Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals.
HD Digital VTX System
HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What's more, pilots can activate and configure its OSD function on Betaflight Configurator.
Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75 Pro HD (ELRS)
Meteor75 Pro HD (Frsky, PNP, TBS)
FC Inside
F4 1S 5A FC (Serial ELRS 2.4G) V2.0
F4 1S 5A FC (SPI Frsky) V3.0
Gyro
BMI270
BMI270
FC Firmware
BETAFPVF411
BETAFPVF411RX
UART Port
One UART Port
Two UART Ports
External RX
Not Supported
Supported
Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD.
Micro Canopy Lite
Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone.
Endurance Boosting Battery
With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots.
Meteor HD Series
BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images.
Meteor75 Pro Frame
Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately.
Powerful 1S Drone Combo
Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots.
Specification
Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX)
Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero)
Camera Adjustable Angle: 0-40°
Motors: 1102 22000KV Motor
Battery: BT2.0 550mAh 1S Battery
Frame: Meteor75 Pro Brushless Whoop Frame
Propellers: Gemfan 45mm 3-Blade Propellers
Canopy: BETAFPV Micro Canopy Lite
Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero)
Receiver: Serial ELRS 2.4G/SPI Frsky/TBS
FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle
Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera
FAQ
Download the FC firmware and CLI dump file for Walksnail and HDZero version.
Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit.
Click to download the manual for HDZero Whoop Lite Bundle.
Includes
1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver
2x BT2.0 550mAh 1S Battery
1x Type-C USB Cable
1x BT2.0 Battery Charger and Voltage Tester
4x 45mm 3-Blade Props (1.5mm Shaft)
1x Screwdriver
1x VTX USB Cable (Walksnail or HDZero Version)
1x Pack of Screws
All products with batteries must be shipped by a ground shipping method.
Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right power performance. BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate a bigger battery.
Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features
The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks.
It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.
Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better.
Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board.
The various colors of the spare parts including the Meteor75 Pro frame and Micro
Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals.
HD Digital VTX System
The Walksnail Avatar HD Mini 1S Lite uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 7.8g lightweight, compatible with 1S whoop drone. Built-in 8 GB storage, this VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode, Betaflight full OSD display is supported and can be adjusted easily by remote control.
Note: Please make sure that the battery voltage must be 3.1V at least when flying, otherwise, the HD digital VTX would stop working.
Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75 Pro HD (ELRS)
Meteor75 Pro HD (Frsky, PNP, TBS)
FC Inside
F4 1S 5A FC (Serial ELRS 2.4G) V2.0
F4 1S 5A FC (SPI Frsky) V3.0
Gyro
BMI270
BMI270
FC Firmware
BETAFPVF411
BETAFPVF411RX
UART Port
One UART Port
Two UART Ports
External RX
Not Supported
Supported
Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD.
Micro Canopy Lite
Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone.
Endurance Boosting Battery
With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots.
Meteor HD Series
BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images.
Meteor75 Pro Frame
Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately.
Powerful 1S Drone Combo
Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots.
Specification
Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX)
Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero)
Camera Adjustable Angle: 0-40°
Motors: 1102 22000KV Motor
Battery: BT2.0 550mAh 1S Battery
Frame: Meteor75 Pro Brushless Whoop Frame
Propellers: Gemfan 45mm 3-Blade Propellers
Canopy: BETAFPV Micro Canopy Lite
Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero)
Receiver: Serial ELRS 2.4G/SPI Frsky/TBS
FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle
Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera
FAQ
Download the FC firmware and CLI dump file for Walksnail and HDZero version.
Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit.
Click to download the manual for HDZero Whoop Lite Bundle.
Includes
1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver
2x BT2.0 550mAh 1S Battery
1x Type-C USB Cable
1x BT2.0 Battery Charger and Voltage Tester
4x 45mm 3-Blade Props (1.5mm Shaft)
1x Screwdriver
1x VTX USB Cable (Walksnail or HDZero Version)
1x Pack of Screws
All products with batteries must be shipped by a ground shipping method.
Experience super clear and sharper images with the BETAFPV Meteor85 HD. Based on the newest Meteor85 (2022), it comes with Walksnail Avatar Mini HD VTX or HDZero Whoop Lite Bundle, bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight. Together with 1103 11000KV motors and GF2015 2-blade props that feature strong propulsion, it gives pilots powerful and impressive results. Enjoy an immersive flight experience for freestyle tricks outdoors, and get the perfect shots with the new HD VTX system.
Features
Lightweight for 52.57g (Walksnail) and 48.30g (HDZero) whoop drone, this new 2S whoop drone with Walksnail HD VTX or HDZero VTX gives pilots an immersive flight experience and impactful visuals.
New frame with the low profile of the battery slot, the drone's gravity center is reduced and improved the sense of compactness, perfectly enhancing the trust-to-weight ratio. It is durable and light enough, giving pilots a good balance of weight and a nice punch on a 2S battery.
Featuring an upgraded propulsion system and a larger capacity battery. Meteor85 uses GF 2015 2-Blade props with 1103 11000KV motors, which gives full play to the efficiency of the power. Combined with a 450mAh 2S battery, Metero85 can fly up to 6 mins (HDZero) and 5 mins (Walksnail).
Adopted with injection molding technique, this canopy is 2.50g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserve solder pads for the external receivers with UART1 and UART2 on F4 1-2S 12A FC board. The SPI ELRS 2.4G and SPI Frsky version can be used as PNP quadcopter.
Specifications
Frame: Meteor85 Brushless Whoop Frame
Motors: 1103 11000KV Motors
Props: Gemfan 2015 2-Blade Propellers
Receiver: ELRS 2.4G
VTX: 1S Walksnail Avatar Mini HD VTX or HDZero Whoop
Battery: 450mAh 2S Battery
Weight Without Battery: 52.57g (Walksnail)/48.30g (HDZero)
Flight Time: 6 mins (HDZero)/5 mins (Walksnail)
Camera Adjustable Angle: 0-45°
FC&ESC: F4 1-2S 12A FC (2022)
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
Camera: Walksnail Avatar Nano Camera/HDZero Nano Lite Camera
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
F4 1S 12A AIO FC
CPU: STM32F411CEU6 (100MHZ )
Gyro: Six-Axis BMI270 (SPI connection)
SPI ELRS 2.4G Receiver
Dimensions: 26mm x 26mm (suitable for whoop pattern mounting hole)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 (ELRS)
Motor Pin Connector: 1.25mm Header Pins
USB Port: SH1.0 4-Pin
Weight: 4.74 g (without power cable and BT2.0 connector)
1S 12A ESC
Input voltage: 1S-2S
Built-in ESC with 12A continuous and peak 25A current
ESC firmware: C_X_30_48_V0.18.1.hex for Bluejay BB51 hardware
Includes
1x Meteor85 Brushless Whoop Quadcopter (2S HD Digital VTX) ELRS 2.4G
1x 450mAh 2S 45C Battery
1x Type-C to SH1.0 Adapter
1x SH1.0 Cable
3x Decorative Parts
4x Gemfan 2015 2-Blade Propellers
1x Walksnail VTX USB Cable (For Walksnail Version)
1x HDZero VTX Converter Cable (For HDZero Version)
1x Pack of Screws
1x User Manual
The BT3.0 2S Whoop Connector Female Set 10 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 10 female BT3.0 2S whoop connectors.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
BT3.0 Female Connector: 0.68g/PCS, 10.1x9.1x5.4mm
BT3.0 Male+Female Connector: 1.28g/PCS
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 2S Whoop Connector Female Set 10 Pack
The BT3.0 2S Whoop Connector Male/Female Set 10 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 5 female and 5 male BT3.0 2S whoop connectors.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
BT3.0 Male Connector: 0.6g/PCS, 11.2x9.2x6.1mm
BT3.0 Female Connector: 0.68g/PCS, 10.1x9.1x5.4mm
BT3.0 Male+Female Connector: 1.28g/PCS
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 2S Whoop Connector Female/Male Set 10 Pack
The BT3.0 2S Whoop Connector Male Set 10 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 10 male BT3.0 2S whoop connectors.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
BT3.0 Male Connector: 0.6g/PCS, 11.2x9.2x6.1mm
BT3.0 Male+Female Connector: 1.28g/PCS
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 2S Whoop Connector Male Set 10 Pack
This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 5 BT3.0 whoop cable Pigtails.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 Male 2S Whoop Cable Pigtail 5 Pack
The BT3.0 2S Whoop adpater Male BT3.0 to HX2.54 cable 5 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 5 BT3.0 to HX2.54 whoop adapter cables.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
BT3.0-XH2.54 Adapter Cable
The BT3.0 connector can serve as a 2S balance charging port and can be used with a conventional 2S balance charger to charge the battery through a BT3.0 male-to-male adapter cable, providing customers with greater flexibility to choose their own charging method.
Specifications
BT3.0 XH2.54 Adapter Cable: 1.84g/PCS, 35mm
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 to HX2.54 2S Whoop Adapter Cable 5 Pack
The BETAFPV Micro RF TX module is based on the Express LRS project, an open-source RC link. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.Check out our RC Transmitters and all our BetaFPV products!
Specifications
Packet refresh rate: 25Hz/50Hz/100Hz/200Hz (915MHz/868MHz),
RF output power: 100mW/250mW/500mW (915MHz/868MHz)
Frequency bands: 915MHz FCC/868MHz EU
Input voltage: 5V~12V
XT30 port: 5V~12V, recommend 2S(8.4V) battery, DO NOT support 3S(12.6V) or above
USB port: Type-C
Note: Please assemble the antenna before power on. Otherwise, the PA chip in the Micro TX module will be damaged permanently.
Note: Please DO NOT use 3S or above battery to power up the TX module via XT30 port. Otherwise, the power supply chip in the TX module will be damaged permanently.
About the firmware
The ExpressLRS offical project on Github does NOT support the OLED function for the moment. BETAFPV team will work with the ELRS team and make the official repository support the OLED and button function ASAP.
Please get the firmware from BETAFPV Github nowadays until ExpressLRS official support. In BETAFPV branch, the ExpressLRS protocol is V1.1.0 and NO binding phrase for the firmware.
NOTE: There are 2 known issues with this firmware currently. We will solve these 2 issues ASAP. If you find more other issue, feel free to leave a issue here.
Only support pressing function for the joystick.
When entering OLED menus page with long pressing, the connection between RF TX module and receiver will be lost, the connection will recover after exiting menus page automatically;
You could all use the ELRS official firmware V2.0-RC2 now, but lost the function of OLED and Joystick. We will work with the ELRS dev team and make the ELRS official firmware support the full function of the Micro TX Module. For the milestone, OLED will be supported in the V2.1 officially.
https://github.com/BETAFPV/ExpressLRS
User manual of How to Flash Firmware of ELRS RX/TX.
Includes
1x BETAFPV ELRS Micro TX module
1x BETAFPV Moxon antenna
1x Micro TX module user manual
1x Spare USB data cable (Type-A to Type-C)
The BetaFPV F4 1S 12A AIO Brushless Flight Controller V2.2 is the default FC for Cetus X brushless whoop quadcopter, also great for 85mm whoop drones like Meteor85 and 3" toothpick drones like HX115 SE Toothpick Drone and HX115 LR Toothpick Drone. BetaFPV updated the FC to V2.2 with BMI270 gyro and BB51 ESC hardware in place of ICM20689 gyro and BB21 ESC hardware.
Check out all our whoop flight controllers, and all our BetaFPV gear!
Specifications
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: BMI270
Built-in Receiver: SPI ExpressLRS 2.4G / Frsky SPI
Receiver antenna: Line antenna
Size: 30mm x 30mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 (ELRS)
OSD: Built-in BetaFlight OSD
Recommend VTX:
Power Cable: 55mm, with BT2.0 connector
Weight: 3.6g (Without power cable included)
Power supply: 1S-2S
Current: 12A continuous and peak 25A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: C_X_30_REV16_7.hex for BB51 BLHeli_S hardware
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Includes
1x F4 1S 12A AIO FC
Wiring Diagram
Based on the F405 2-4S 20A Flight Controller V4, the F405 4S 20A Toothpick Flight Controller V5 applies a new ICM42688 gyro and ESC chip that comes with BLUEJAY ESC firmware so it supports bidirectional D-shot. In addition to plug-and-play ports for the receiver and HD Digitial VTX, the same as the V4 board, the V5 board is made with a more rational layout for easy solder and preventing solder from jumping to another pad and shorting components.
Check out all our whoop flight controllers, and all our BetaFPV gear!
Features
Not only is the flight controller board made with a rational layout, but it is also designed with larger solder pads. It is very easy for pilots to solder external electronics.
The flight controller is capable of handling 20A continuous current and reaching 25A peak current due to high-quality MOSFETs.
Soldering motor wires to the pad directly allows lower resistance for more current on motors. Besides, solder pads are reinforced by thick copper and edge plating processes, ensuring a solid value and durable use.
Reserving the UART ports layout, UART3 for RX, UART4 for HD digital VTX, UART6 for Analog VTX, and UART1 for spare use, it is more convenient for pilots to solder.
This board comes with a 25.5x25.5mm whoop mounting pattern; this board can be added to both the toothpick drone and the cinematic whoop quadcopter
Note: F405 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLUEJAY firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it.
Comparison to F405 2-4S 20A V4 FC
We upgraded the F405 2-4S 20A V4 board to V5 by adopting ICM42688 gyro instead of MPU6000 and adding some new features. ICM42688 gyro works great in most cases. Except for the gyro, the V5 board comes with a completely new ESC firmware that supports bidirectional D-shot. The way to connect motors changed and is solderable only on the V5 board. Besides the V5 FC board features high-quality material for stability and durability. The below pictures show the difference between the two flight controllers.
Note: The F405 2-4S 20A Flight Controller V4 with BMI270 gyro will be available for purchase for a period of time.
Diagram for Toothpick F405 20A AIO FC V5
The board integrates 2 LEDs, including the Power LED (Red) and the FC LED (Blue).
LED
Status
Description
Power LED (Red)
Solid
Power on
FC LED (Blue)
Solid
Motor Armed
Connecting External RX/HD Digital VTX
F405 4S 20A FC V5 integrates the Plug & Play port for the external RX and HD digital VTX, and there will be a 4-pin connector for RX and a 6-pin connector for HD digital VTX in the package. Thus, we highly recommend pilots use the port to save the solder work.
FC & ESC Firmware:
The default firmware is including CLI dump file. But if you flash firmware from the Betaflight configurator official site, please flash a CLI dump file for F405 4S 20A FC V5. We offer the default firmware and CLI dump file to download.
Download the FC default firmware betaflight_4.3.1_BETAFPVF405 and CLI dump file.
F405 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLUEJAY firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it. Here are the download links for two firmware.
Here are the download links for ESC firmware. Please configure the BLUEJAY firmware through ESC - Configurator or Bluejay Configurator software.
Download the BLUEJAY ESC firmware
Download the ESC - Configurator
Download the Bluejay Configurator
We offer BLHeli_S ESC firmware for pilots. Please configure the BLHeli_S ESC firmware through BLheliSuite, BLHeli - Configurator, or ESC - Configurator software.
Download the BLHeli_S ESC firmware
Download the BLHeliSuite16714902a
Download the BLHeli - Configurator
Download the ESC - Configurator
frame like Pavo25 and X-knight 35.
Specifications:
Flight Controller
CPU: STM32F405RGT6
Six-Axis: ICM42688 (SPI connection)
Mounting Size: 25.5x25.5mm (M2 Anti-vibration rubber damper available)
FC Firmware: betaflight_4.3.1_BETAFPVF405
OSD: Built-in Betaflight OSD (OSD chip: AT7456E)
Receiver: SBUS/CRSF/DSMX Receiver
BEC: 5V 3A
Built-in current sensor
Weight: 8.35g
ESC
ESC Chip: SILABS EFM8BB21F16G-C
Support D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Input voltage: 2S-4S Lipo
Continuous current: 20A
Peak current: 25A
Firmware: G_H_20_48_v0.16.HEX (Default BLUEJAY), BLHeli_S (Optional)
Includes
1x BetaFPV F405 V5 2-4S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ICM42688
1x Cable Pigtail (XT30)
1x 6-Pin Connector for Digital VTX
1x4-Pin Connector for RX
4x M2x12 Screws
8x M2 Nuts
4x M2 Anti-vibration Rubber Dampers
F722 2-6S AIO 35A FC is a very reliable FC that is made to meet your advanced FPV needs. Comes with an F722 chip and a BLHeli_32 ESC, this board provides a better performance capability and higher calculation speed, which brings pilots a more stable and smoother flight. What's more, F722 AIO FC has specially added a 6-pin connector for DJI Digital VTX, just plug & play, less solder work needed, super easy to install. It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery.
Check out all our whoop flight controllers, and all our BetaFPV gear!
A very in-depth video on the BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller.
Features
Built-in STM32F722RET6 CPU, F722 FC is more powerful than F4. It features a fast processing speed and stable performance, providing reliable and smooth flight for 4"-5" drones.
F722 AIO 35A FC has specially added a 6-pin connector for HD Digital VTX, just plug & play, less solder work needed, perfect for the pilots who enjoy the HD Digital VTX system.
6 full UARTs are available on this board. With plenty of UARTS, Pilots could have more options for external parts like VTX, GPS, Receiver, and other components.
It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery, and gives the drone a more robust flight performance.
With the 6S battery and this F722 35A AIO FC, the drone will break through the limit of the power of the toothpick drone, exploring more possibilities in 4-5'' drones.
The new BLHeli_32 ESC version is built-in a 16MB flash memory chip dedicated to Blackbox logging, which is an extremely powerful tool for tuning and troubleshooting an FPV drone. It has a faster processing speed and up to 128k PWM frequency, providing a more stable and smoother flight for pilots.
V2 with BLHeli_32 ESC
V1 with BLHeli_S ESC
PWM Frequency
24k-128k
24k-96k
ESC Firmware
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
Blackbox
16MB
Not included
Weight
9.00g
7.06g
Board Thickness
1.6mm
1.4mm
BLHeli_32 ESC Firmware
The F722 35A AIO FC has two boards with different ESC versions for choice. The V2 board uses AT32F421G8U7 MCU, a 32-bit ESC chip, with BLHeli_32 ESC firmware. This firmware supports up to 128k PWM frequency, featuring faster processing speed and unlocking more functions for the flight.
BLHeli_32 ESC
BLHeli_S ESC
MCU
AT32F421G8U7
EFM8BB21F16G-C
Firmware Version
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
PWM Frequency
24k-128k
24k-96k
Bidirectional DSHOT
Support
Support
Signal Support
PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Know More About ICM42688 Gyro
The F722 FC ICM42688 version has the same solder pad and layout as BMI270 except for the gyro chip. Besides, you can also find the difference in Betaflight settings.
The ICM42688 gyro supports 8.00 kHz gyro update frequency compared with the BMI270 gyro which supports 3.20 kHz. When using a 6S battery, the ICM42688 gyro has a good performance.
The degree between ICM42688 and BMI270 gyro is different. When configuring F722 FC ICM42688 version, the gyro degree should be set to CW270°.
Diagram for F722 35A AIO FC
The below picture is the top front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
The below picture is the bottom front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
There are 2 LEDs on the bottom of the board to indicate the status, including the FC LED (Blue) and FC Power LED (Red). The LED status for V1 and V2 boards are the same.
LED
Status
Description
FC LED (Blue)
Solid
Armed
FC LED (Blue)
Extinguished
Disarmed
Power LED (Red)
Solid
Power on
How to Connect the External RX&VTX
To connect the external RX&VTX, please refer to the below diagram. F722 35A AIO V1 and V2 boards have the same soldering pad and connecting ports.
Specifications
Flight Controller
Item: F722 35A AIO Brushless Flight Controller
Weight: 9.00g (BLHeli_32)
CPU: STM32F722RET6
Six-Axis: ICM42688
Mounting hole size: 26mmx26mm
Firmware version: betaflight_4.3.0_STM32F7X2
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Support programmable LED like WS2812 etc
Built-in current sensor
Blackbox: 16MB (V2 with BLHeli_32 ESC included)
ESC
Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/TBS Crossfire Receiver (requires external connection)
Input voltage: 2S-6S Lipo
Continuous current: 35A
Peak current: 40A
ESC firmware: BETAFPV_35A_V2_BLHeli_32_Multi_32_9 (BLHeli_32)
Indicators: Power indicator (Red) / FC indicator (Blue)
Capacitance: CS|5*10*13mm|470μF|35V
Connector: 80mm 14AWG silicone cable with XT60
Recommended motors: 14XX series, 15XX series, 16XX series, 18XX series, 20XX series
Includes
1x BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller (w/ 35A 32Bit 4in1 ESC) - ICM42688
This frame is customized for 85mm whoop drone and the frame for Meteor85, Meteor85 HD Digital VTX. With a marvelous design on the battery slot which keeps a low profile and triangle bilateral stretch structure of motor mounting position, this frame weighs only 11.32g.
Features
The new design frame reserves a battery slot, making it conveniently free from the battery strap and perfect for BETAFPV 450mAh 2S battery compared to the previous 85mm whoop frame.
With the low profile of battery slot height, the drone's gravity center is reduced, and improved the sense of being compact.
Meteor85 frame’s motor mounting position uses a triangle bilateral stretch structure, making the frame more aesthetic. It provides you more durable and smoother flight experience.
The ultra-light and durable frame is PP material only 11.32g, which can match the F4 1-2S 12A AIO Brushless Flight Controller.
The frame is suitable for 2" propellers.
Recommend using BETAFPV canopy for nano HD camera, which is suitable for Caddx ant camera, or other nano cameras. It can also match the lighter BETAFPV canopy for a micro camera and install with a C02 Camera, C03 Camera, and M03 5.8G VTX.
Specification
Material: PP
Wheelbase: 87.7mm
Motor mounting hole: 110x motors, such as 1103 11000KV motors
FC mounting hole: fully compatible with whoop style FC board mounting pattern, 26mm x 26mm
Weight: 11.32g
Includes
1x Meteor85 Brushless Whoop Frame (Grey or Black)
Pavo Pico is the tiniest 2S Sub100g DJI O3 Cinewhoop frame, working with other popular HD digital VTX such as Walksnail Avatar Pro Kit, Vista Kit, etc. After testing with pilots, this frame has been upgraded by lowering the battery slot height and adding filters and camera protection parts. These updates enhance the camera and HD digital VTX, to give pilots an unparalleled flying experience.
The Pavo Pico is an all-new HD 81mm cinewhoop with 45mm props that is designed to be the smallest 2S-3S, sub100g build.
Check out the rest of our micro frames and the rest of our BetaFPV gear!
Features
HD digital VTX bracket made of lightweight and tough injection-molded PP material with an adjusted structure to prevent HD VTX displacement or loss after the crash.
Incorporating an angle-limited lens protection print and DJI O3 series filters, It is recommended to purchase, which can increase safety and improve visual quality.
The Rubber Damper Vibration damping design reduces low-frequency vibrations and is used with GyroFlow stabilization software for a stable and clear camera image during high-speed flight.
To accommodate a wider range of battery sizes, the main body of the frame can be trimmed through DIY methods. Additionally, larger batteries can be installed by using battery straps or printed components.
The DJI O3 can be directly installed, while Avatar and Vista require a 20x20 mounting plate and screws (included) for fixation. The naked frame is suitable for users who DIY refit and assemble the HD VTX by themselves.
We offer a wider range of colors for the Pavo Pico frames, giving you even more options to choose from. Whether you prefer a bold and bright hue or a more subdued shade, we have a color that will suit your style. You can choose your favorite color or collect them all to create your own unique mix-and-match cinewhoop.
Pavo Pico Frame Kit
We used ultra-light PP material to make the HD VTX mounting bracket, increasing its toughness. The antenna fixing slot and frame have been fused to reduce damage risk, while the camera's installation height has been lowered with a protective printed part to limit its movable angle to within 30°. Additionally, an O3 filter can be used to protect the lens and enhance image quality. We have incorporated a unique rubber damper vibration-damping design, used with GyroFlow stabilization software, which greatly enhances safety and ensures a smooth, HD image output. When you screw the die-cast screws, please DO NOT screw them too tight to leave room for rubber dampers to absorb vibration. It may cause jello in the video footage.
Click to watch the installation guide video for DJI O3 Air Unit on Pavo Pico.
And The whoop quadcopter package includes the DJI O3 HD Digital VTX Antenna Mount.
DJI O3 Vibration Problem
To tackle the challenge of vibration on many whoop drones, the DJI O3 unit is mounted on a carbon fiber plate with 4 rubber dampers. This innovative design ensures peak performance and perfect stability.
Troubleshooting
To improve video quality when recording with DJI O3 HD VTX, turn off its electronic stabilization and use GyroFlow stabilization software.
When fixing the HD VTX bracket with M1.4*10 screws, ensure that the nut just touches the shock-absorbing ball.
The Jello effect may occur during the above installation due to 2 reasons:
The VTX bracket is over-tightened with the screw and the rubber dumper is totally deformed. To solve this, make sure that the screw is tightened just enough to touch the shock-absorbing ball and keep the ball and bracket loose.
If It is a large deformation of the frame or quadcopter blades, replace the frame or blades with larger vibrations if necessary.
Note: use acetate tape to bind motor wires and prevent them from drooping and interfering with the propeller's rotation.
Upgrade Low Profile Design
After collecting feedback through the BETA TEST, we lowered the height of the HD VTX mounting bracket and whoop duct from 60.6mm to 51.5mm and the battery compartment results in a more low profile on the cinewhoop.
Pilots can further customize their cinewhoop with DIY options such as battery straps or printable components, allowing for compatibility with a variety of battery sizes. This enables pilots to tailor and enhance their cinewhoop to meet their specific requirements and preferences. Steps as follow:
Specification
Item: Pavo Pico Brushless Whoop Frame
Material: PA12
Wheelbase: 80.8mm
Battery Slot Size: 16mmx12.7mm
Camera Installation Spacing: 19mm/20mm
Color: Black
Weight: 11.62g
Motor Mounting Hole Position: 3-M1.4-φ6.6mm
FC Pattern: 26×26mm, suitable for F4 1S 12A AIO Brushless FC V3
Includes
1x BetaFPV Pavo Pico HD 81mm Cinewhoop Frame (HD Digital Version) - Black
All batteries must be shipped by a ground shipping method.
Whether you're a skillful pilot or a new beginner, the Cetus X FPV Kit is an advanced 2S power whoop bundle, and a primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. With the combination of Cetus X Brushless Quadcopter, LiteRadio 3 Radio Transmitter, and VR03 FPV Goggles, get ready for the next level of flying FPV.
Be sure to pick up some extra batteries so that you can fly all day! We recommend the following 1S batteries for this quad:
BetaFPV 1S 300mAh - BT2.0
Check out our other RTF combos, all our pre-built quads, and our BetaFPV selection!
Features
Nothing quite beats the experience of flying Cetus X with an enhanced propulsion system, and longer radio and video transmission. With a very functional and potential remote controller and FPV goggles, pilots can unlock more accomplishments to the next level.
Two FC versions are offered for pilots. With the support of the Betaflight configurator, beginners can learn quadcopter configuration through the Betaflight FC version. For pilots who prefer the classical Cetus, the Cetus FC version with an altitude hold function is also coming soon.
Classical white design inherited from Cetus Series and made of PA12 material, the Cetus X frame has an excellent impact resistance in drop & impact and reduces the risk of damage, giving you more peace of mind.
The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.
LiteRadio 3 reserves a nano bay that supports the external TX module for the compatibility of more quadcopters. And the VR03 FPV goggles which are newly added a Micro SD card slot to save the video with DVR recording, support most Analog VTXs in the market.
The quadcopter, radio transmitter, FPV goggles, and all of the accessories are packed in an EVA portable storage bag. It is convenient to carry outside and better to protect the equipment.
Powerful Propulsion System
Equipped with 1103 11000KV Brushless Motors and Gemfan 2020 4-blade props, the Cetus X Brushless Quadcopter delivers powerful propulsion, making it a 2S power whoop drone with some real punch to it. The whole quadcopter is light and durable enough, offering pilots a high-efficiency flight experience.
Recording Every Flight Moment
Newly developed by BETAFPV, and based on VR02 FPV Goggles, the VR03 FPV Goggles take features of VR02 and come with a DVR recording function. Pilots can enjoy the playback saved through the goggles or export the videos by Micro SD card. This exciting function allows pilots to catch the memorably breathtaking moment, greatly heightening the FPV flying experience.
Improved Video Transmission
Cetus X Brushless Quadcopter comes with M04 25-400mW VTX and C04 FPV camera. M04 25-450mW VTX features a lightweight and adjustable output power for long-distance flying. Combining this VTX and the excellent radio link ExpressLRS 2.4G, pilots can fly whoop drones longer to explore more possibilities and have fun. In addition, the C04 FPV camera (based on Caddx Nano Ant Camera/Runcam Nano 4) shows better quality in FPV flight compared with the C02 FPV camera.
LiteRadio 3 Radio Transmitter
This transmitter features an ergonomically designed handle and has superb performance in its working time, a newly updated gimbal. Besides, this version supports BETAFPV Configurator, which is a utility designed to simply update, configure, and tune the radio controller. Experience the thrill of total immersion with unrivaled control and capture the world around you.
FPV Simulator Supported
First time flying a quadcopter? You can learn and practice flying a quadcopter through an FPV simulator before real flying. LiteRadio 1 supports playing FPV simulators like DRL/DCL/Uncrashed/Liftoff. LiteRadio 1 is capable of practicing and charging at the same time. Check out the Liftoff flying demonstration here. Download Liftoff here.
Various Modes, Accessible to All
Cetus X supports Angle/Horizon/Air Modes, which can satisfy the different needs of pilots and adapt to various flight environments. When the quadcopter falls to the ground and upside down, you can activate turtle mode by LiteRadio 3 transmitter to flip it over and resume flying. Whether you're a seasoned FPV pilot or a complete beginner, the Cetus X FPV Kit helps anyone fly confidently from day one.
BETAFPV Cetus Series
The BETAFPV Cetus Series has been very popular since its release in 2021 and become the primary FPV choice for new beginners. Whether propulsion system, radio transmitter, VTX range, or other functions, BETAFPV never stops step to make the product better. From the initial Cetus to Cetus X so far, Cetus Series always satisfies customers' needs no matter new beginners or seasoned pilots.
Specification
Item: Cetus X FPV Kit
Weight: 55g
Wheelbase: 95mm
FC: F4 1S 12A FC
Motors: 1103 11000KV Motor
Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G (Betaflight)/Frsky D8 (Cetus)
VTX: M04 25-400mW VTX
Quadcopter: Cetus X Brushless Quadcopter
Transmitter: LiteRadio 3 Radio Transmitter
Goggles: VR03 FPV Goggles
Battery: 2x BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins
Includes
1x Cetus X Brushless Quadcopter (Betaflight Firmware, ELRS 2.4G Receiver)
1x LiteRadio 3 Transmitter (ELRS 2.4G)
1x BETAFPV VR03 FPV Goggles
4x BT2.0 450 mAh 1S Lipo Battery
1x BT2.0 Battery Charger and Voltage Tester
1x USB Charging Cable (Type-C)
1x Type-C to FC Adapter
1x Prop Removal Tool
4x Gemfan 2020 4-Blades Prop (Spare Set)
1x Portable Storage Bag
FAQ
For more info and instructions, please check the User Manual for Cetus X FPV Kit.
Please DO NOT configure ESC or Motor settings on the Betaflight configurator.
The VR03 FPV goggles do not include a Micro SD card. You should prepare it before using the DVR recording function.
The External TX module for LiteRadio 3 should be bought separately. Recommend BETAFPV Nano TX Module.
Based on ELRS V3.3 and collaborated with ELRS developer team, the First Ever Gemini Dual-Frequency Diversity Transmitter comes out! At present, SuperG Nano Transmitter can be fully activated to achieve the best link quality ever combined with diversity rx such as SuperD receiver or SuperP receiver. With dual 1W transmit power, it excels in anti-interference performance and stability, making it the ideal solution for demanding applications like FPV racing, long-range flight, and professional photography.
Check out our RC Transmitters and all our BetaFPV products!
Features
Introducing the pioneering Gemini Dual-Frequency Diversity Transmitter, propelling ELRS into the era of dual-frequency capabilities.
Dual 1W transmit power experienced amplified signal strength, expanded transmission distances, and a substantial increase in remote control range.
In conjunction with existing true diversity receivers, activating the Gemini mode ensures unwavering signal stability even in the most intricate radio environments.
Meticulously crafted from CNC aluminum alloy, the transmitter casing facilitates efficient thermal conductivity, complemented by an intelligently designed Heatsink system for optimal heat dissipation.
Featuring 2 customizable buttons and 1 USB port, the transmitter accommodates external power sources, enabling steadfast long-range expeditions.
Diagram
Below is the diagram for the SuperG Nano Transmitter.
Note: Please assemble the antenna before powering on. Otherwise, the PA chip in the SuperG Nano Transmitter will be damaged permanently.
The following is the comparison information of the 3 products SuperG Nano Transmitter, ELRS Nano TX Module and ELRS Micro TX Module. It shows the advancing updates and specifications more than ever.
SuperG Nano TX
Nano TX
Micro TX
Max RF Power
Dual-1000mW
500mW
500mW/1000mW
RF Chip
Dual SX128x
Single SX128x
Single SX128x
Antenna Mode
Gemini
Single
Single
Cooling System
Supported
Unsupported
Supported
Backpack
Supported
Unsupported
Supported
External Power Supply
Supported 7-13V
Unsupported
Supported 5-12V
Know More About Diversity&Gemini
Antenna Diversity mode, two antennas. Switch the two antennas regularly to read the RSSI value of the signal and determine which antenna to use to receive data.
True Diversity mode, where both antennas receive data at the same frequency, and the antenna that receives the correct data first is used.
Gemini mode, where two antennas simultaneously receive telemetry data with a frequency difference of 40MHz. They also transmit data simultaneously but at different frequencies. This means that you can receive the same data packets on different frequencies and antennas. This mode provides stable flight even in complex radio environments.
Among them, Gemini is the most advanced function yet of ExpressLRS - Gemini mode currently! It owns the most stable mode for receiving signals and offers higher resistance to interference and stability, making it suitable for various applications.
SuperG Nano Transmitter features Gemini mode. In a testing video by developer Jye Smith, it is shown that with a refresh rate of 1000Hz, the LQ value fluctuates between 90-100 when the true diversity receiver is in operation. However, after switching to Gemini mode, the LQ value stabilizes at 99-100. This demonstrates that ELRS goes to great lengths to ensure link stability.
Combination with Diversity RX
Gemini mode is built upon the hardware foundation of true diversity receivers and requires a dual RF output high-frequency module. When used with Super series products, the advantages of Gemini mode can be fully utilized. And The effects of using the transmitter and receiver in various modes are as follows:
TX
RX
Antenna Receiving Mode
ANT1/ANT2/Switch
Single
Single
Diversity
Diversity
Gemini
Single
Gemini
Single
Single
Diversity
Diversity
Gemini
Gemini
Using it together with True Diversity Receiver ensures a super stable yet strong radio link for pilots to fly in any environment that require extremely stable signals and low latency. Including long-range flights, multiplayer flights, and FPV racing. It gives pilots a robust and aggressive flight experience.
Dual 1W Output Power
The SuperG Nano Transmitter with Dual-active Antennas@Dual Frequencies, each boasting a powerful 1W transmission power. Experience stronger signals, longer transmission distances, and enhanced remote control range.
Cooling System Iteration
The casing part is made of CNC aluminum alloy with an anodized surface for durability. It efficiently dissipates heat, thanks to its optimized internal airflow and high-speed fan with copper heat fins. Fly with confidence and enjoy reliable performance every time.
Combination with Most Radio TX
The SuperG Nano Transmitter could be configured via LUA script. EdgeTX and OpenTX radio transmitter that supports CRSF could be used easily. It available for popular Nano interface TX when used with Micro-Nano Module Adapter including Radiomaster TX16, Boxer, Zorro. Jumper T16, T20, T Pro. Frsky QX7, X9, X Lite.
Note: LiteRadio 3 Pro Radio Transmitter cannot support dual transmitter power above 100mW due to power supply issues.
Express Yourself in Vibrant Colors
SuperG Nano Transmitter is a cutting-edge device that offers a distinct and personalized flair, with a range of three vibrant color options including red, grey, and black. The combination of its sleek design, superior functionality, and colorful choices perfectly caters to those who seek elevate style and performance.
ELRS Series
The ExpressLRS Series expands its lineup with the addition of SuperG Nano Transmitter. To achieve exceptional link quality, pair the Gemini TX with Super series diversity receivers. BETAFPV takes the flying experience to new heights by introducing ELRS links that offer long-range capabilities, low latency, and high refresh rates in a radio control system.
Basic Configuration
SuperG Nano Transmitter is designed to receive signals using the Crossfire Serial Data Protocol (CRSF). Therefore, the interface of the transmitter's high-frequency module needs to support CRSF signal output. Taking the EdgeTX transmitter system as an example, we will explain how to configure the transmitter to output CRSF signals and control the transmitter using Lua scripts.
In the EdgeTX system, navigate to MODEL SEL and enter the SETUP menu. Disable Internal RF (set to OFF), enable External RF, and set the Output Mode to CRSF, as shown in the picture below.
Lua scripting is a lightweight and compact scripting language that can be embedded in the transmitter for convenient access to and modification of the transmitter's configuration.
Download the elrsV3.lua script from the BETAFPV Support Center or ExpressLRS Configurator.
Copy the official Lua script, elrsV3.lua, to the SD card of the transmitter, under the path Scripts/Tools.
On the EdgeTX system, long-press the SYS button or MENU button to access the SD-HC CARD menu.
In this menu, select the elrsV3.Lua script and run it.
If the Lua script runs successfully, the interface will appear as shown in the illustration below.
Custom Buttons
SuperG Nano Transmitter reserves 2 buttons that can be customized by users. Here are the specific steps to operate:
Enable the transmitter's WiFi or power it on and wait for 60 seconds to enter WiFi mode using LUA programming.
The RGB indicator light will slowly flash in green, indicating that the transmitter has automatically enabled WiFi (WiFi name: ExpressLRS TX, WiFi password: expresslrs).
Connect your smartphone or computer to the WiFi network and open a web browser. Enter http://10.0.0.1 to access the custom button settings page.
In the corresponding button's Action column, select the desired custom function. Then, choose the button type and the number of presses or duration in the Press and Count columns. Click SAVE to complete the settings.
Currently, there are 6 available functions that can be assigned to shortcut buttons. There are 2 ways to use the buttons: long-press and short-press. The duration of a long press can be customized, while the number of presses for a short press can also be customized.
The following are the 6 functions that can be set:
Unused
VTX Setting
Increase Output Power
Enable WiFi
Enter VTX Channel
Enter Binding Mode
Enter VTX Band
The pictures below show the functionality of the transmitter in its factory default settings. (The left button is Button1 and the right button is Button2).
Button
Action
Press
Count
Button1(Left Button)
Enter Binding Mode
Short Press
3 Times
Increase Power
Long Press
For 0.5 seconds
Button2(Right Button)
Go to VTX
Channel Menu
Short Press
2 Times
Send VTX Settings
Long Press
For 0.5 seconds
Note: This transmitter hardware does not support button RGB lights.
Bind & External Power Supply
The SuperG Nano Transmitter utilizes the default firmware, which employs the ExpressLRS V3.3.0 official protocol without a Binding Phrase. Consequently, the binding receiver should also be equipped with firmware V3.0.0 or higher and have no Binding Phrase set. For optimal performance, it is recommended to position the transmitter's two antennas as far apart as possible.
Put the receiver in a bound state and wait for connection.
Click the "Bind" in the Lua script or the set custom button to enter the binding mode.
If the Indicator has turned solid, it indicates that the device has been bound successfully.
Note: If the firmware of the TX is reflashed and the Binding Phrase is configured, you cannot enter the Binding state through the above method. Please set the RX to the same frequency Binding Phrase, and the TX and RX can be connected automatically.
When the dual transmit power exceeds 500mW, the SuperG Nano Transmitter exhibits relatively high power consumption, leading to a reduced battery life. To prolong the transmitter's usage time, it is advisable to utilize an external battery as a power source.
The power consumption of the transmitter is not only related to the transmit power but also to the telemetry ratio. When using high power of 500mW and above, the return ratio can be set higher to reduce power consumption and extend use time.
For example, in Gemini mode, the power consumption of setting the return ratio to 1:128 is 1000mA, while the power consumption of setting the return ratio to 1:2 is only half of 1:128.
Note: When the voltage of the radio transmitter battery or external battery is lower than 7V (2S) or 10.5V (3S), please use the Gemini mode of 500mW and 1W carefully, otherwise the transmitter will enter the restart state due to insufficient power supply, resulting in disconnection out of control.
FAQ
When establishing a link, it is not possible to enter the LUA script.
The ELRS LUA script version is outdated and requires an upgrade to elrsV3.lua.
The baud rate of the radio transmitter is set below 400K, and it should be adjusted to a value above that.
If there is no option to modify the baud rate, it is necessary to update the radio transmitter firmware, ensuring that EdgeTX is at version V2.7.0 or newer.
If your radio transmitter is unable to use the F1000 Packet rate or prompts "Baud rate is too low".
Reason: F1000 requires a baud rate higher than 400K, and the radio transmitter's baud rate is 400K by default.
Solution: First update the baud rate (greater than 400K) setting in the Hardware from the Model Setup menu or System menu, then restart the radio transmitter to ensure the baud rate setting has been applied. Then change the Packet rate.
When the F1000 is turned on, the Packet rate between the radio transmitter and the SuperG Nano Transmitter is less than 1000.
Reason: EdgeTX version problem
Solution: The EdgeTX version needs to be upgraded to 2.8.0 or above. And the LiteRadio 3 Pro Radio Transmitter defaults to EdgeTX 2.8.0 and does not have this problem.
The SuperG Nano Transmitter's default firmware is ELRS V3.3.0, and users need to update the receiver to V3.0.0 or above to bind the frequency.
Download the Instruction Manual for the SuperG Nano Transmitter
Download the firmware for the SuperG Nano Transmitter
Download the Backpack firmware for the SuperG Nano Transmitter
Download the STL File for the SuperG Nano TX Insulated shell
Specification
Item: BETAFPV SuperG Nano Transmitter Module | ELRS 2.4G
Weight: 44.8g
Color: Black, Red, Grey
Antenna Connector: 2x RP-SMA
RF Power: 25mw/50mW/100mW/250mW/500mW/1000mW
Packet Rate: 50Hz/100Hz/150Hz/250Hz/333Hz/500Hz/D250/D500/F500/F1000
Frequency Band: 2.4GHz ISM
Backpack: support
Input Voltage: 7V~13V DC
Rated Current: 8V,1000mA@1000mW, 1:128, Gemini mode
USB Port: Type-C
Fan Voltage: 5V
Default Firmware Version: ExpressLRS V3.3.0
Target Name: BETAFPV SuperG Nano 2.4GHz TX
Includes
1x SuperG Nano Transmitter (Black/Red/Grey)
2x 2.4G Glue Stick Antenna
1x USB to Type-C Data Cable
1x Type-C Male to XT30U Male Power Cable
1x GH1.25 Male to FUTABA Male Signal Cable
1x Micro-Nano Module Adapter (Standard Version)
1x Double Side EVA Foam Tape
1x Instruction Manual
1x Service Card
These screws and rubber dampers are really useful for mounting your Whoop / Toothpick FC.
Check all our whoop frames & accessories and the rest of our BetaFPV selection!
Specifications
M1.2* 4 screws fit for stock Blade Indcutrix frame / 65mm frames.
M1.4* 5 screws fit for Eachine black E010 frame / 75mm / 85mm frames.
Black rubber dampers has a gap of 0.8mm, suitable for ALL brushed FC boards.
White rubber dampers has a gap of 1.2mm, suitable for 2S AIO FC boards, F405 FC stack etc.
Blue rubber dampers has a gap of 1.8mm, suitable for 2-4S AIO FC boards.
Includes
20x M1.2* 4 screws
20x M1.4* 5 screws
20x Black rubber dampers
20x White rubber dampers
20x Blue rubber dampers
BLH4421, Blade 2S 15C LiPo (7.4V/320mAh)
Blade 2S 15C 7.4V 320mAh LiPo. This is a replacement battery intended for the Blade 150 FX helicopter. Package includes one 2S 7.4V 320mAh LiPo battery.
This product was added to our catalog on October 3, 2022
The Caddx FPV Walnut Action Camera features 4k/60fps picture quality, IP64 waterproof rating, and gyroflow for stabilization This impact-resistant camera weighs only 60g and has optional ND8 and ND16 Filters.Check out all our HD Action Cams and our Caddx Selection!
Features
One-Key Startup
4K/60fps high-definition picture quality with 100mbps bit rate
Screw On ND8 and ND16 Filters
The fuselage comes with a battery
A hard shell with a soft rubber interior design makes it impact-resistant
IP64 Waterproof Rating
Magnetic Charging
63.4g in Weight
Gyroflow can be used for post stabilization
Specifications
Input Voltage: Type-C, 2S-6S BEC, Magnet
Video Resolutions:4K/60fps,4K/30fps(4/3),2.7K/60fps,2.7K/30fps(4/3), 1440P/60fps,1080p/120fps.
SD card: Max 256G
Video Format: MP4
Video Encode: H.264/H.265
Video Max Bitrate: 100Mbps
Wifi: 5GHz
Dimensions: 38x36
Weight: 60g
FOV: 150”
Image Rotate: support
Includes
1x Caddx Walnut FPV Action Camera
1x Adjustable Camera Mount
1x Charging Cable
1x Thumb Screw
1x Camera Case
1x Lens Cloth
1x Cable Set
1x ND8 Filter & 1x ND16 Filter (if not CAM ONLY version)
All batteries must be shipped by a ground shipping method.
CNHL always gets the power we need for the price we love! This 3pack or 450mah 2S batteries is perfect for your 2'' - 3'' craft.
Check out our other 2S batteries and all our CNHL products!
Specifications
Capacity: 450mAh
Voltage: 7.6V / 2-Cell / 2S1P
Discharge: 70C Continual / 140C Burst
Charge Rate: 5C Max
Size: 13.8x18.1x61.8mm
Weight: 32g (Including wire and connector)
Output Connector: XT30
Balance Connector: JST / XH
Wire Size (AWG): 18#
Includes
3x CNHL MiniStar 7.6V 2S 450mAh 70C LiPo Micro Battery - XT30
Darwin FPV BNF Tiny Ape Freestyle 2S 2.5" Quad is the first 2.5'' drone from Darwin fpv. Designed to meet the needs of more pilots, it comes with the Darwin F411 15A Bluejay AIO FC with integrated ELRS2.0 RX, 25-600mW VTX and RunCam Nano 4. Check out the reviews below!
Make sure to check out all of our BNF quads as well as the rest of our DarwinFPV selection!
Specifications
FC&ESC：F411 1-3S 15A FC(Built-in ELRS 2.4G receiver)
Built-in Receiver Protocol: SPI ELRS 2.4G
Motor: 1103 8000KV Brushless Motor
Camera: RunCam Nano 4
VTX: 25-600mW VTX
Propeller: Gemfan 2512 3-blade propeller
AIO Firmware Target: DARWINF4SX1280HD
ESC Firmware: Bluejay_S_H_50_48_v0.14
Recommended Battery: 2S 380-450mah
Weight: 50.3g w/o battery & props
Includes
1x DarwinFPV BNF TinyApe Freestyle 2S 2.5" Quad - ELRS
All products with batteries must be shipped by a ground shipping method.
This battery was designed specifically for the DJI FPV Goggles V2, on a full charge, it can power 110 minutes of FPV immersion!
The built-in charge indicator will keep you up to date on the battery's charge, no tester required.
Check out the DJI FPV System product line!
Specifications
DJI FPV Goggles Battery Capacity: 1800mAh
Voltage: 9 V (Max.)
Type: LIPO 2s
Charging Temperature: 0°C to 45°C
Energy: 18 Wh
Max Charging Power 10 W
Battery Life: Approx. 110 minutes (measured in an environment of 25°C at maximum brightness level)
Includes
1x DJI FPV Goggles V2 Battery
DYNB0012, Dynamite 2S LiPo Battery (7.4V/350mAh)
The Dynamite 7.4v 350mAh 2S LiPo Battery is intended for use with the Axial 1/24 Scale Deadbolt Mini Crawler. This package contains one 2S LiPo to replace the kit supplied battery.
This product was added to our catalog on June 5, 2021
DYNB0110, Dynamite Jet Jam Pool Racer 2S Li-Ion Battery (7.4V/1500mAh)
This is a replacement Dynamite 7.4V 1500mAh Jet Jam Pool Racer 2S Li-Ion Battery, intended for use with the Jet Jam Pool Racer.
Specifications:
Approximate Assembly Time: No assembly required
Beam: 4.5 in (114.3mm)
Boat Type: Deep-V
Completion Level: Ready-To-Run
Drive System: Jet Drive
Hull Height: 3 in (76.2mm)
Hull Material: Injection Molded ABS
Length: 12 in (304.8mm)
Motor Size: 390 Brushed
Radio: Pro Boat 2.4GHz
Recommended Battery: 1500mAh 7.4 LiIon
Scale: 12 inch
Speed Control: 2 in 1 Brushed ESC/RX
Steering: Jet Drive
Trim Scheme Colors: Orange with 3 Decal Options
Type: RTR Deep V Jet Boat
Weight: 1 lb (0.5kg)
This product was added to our catalog on July 30, 2021
Key Features
Fits most 1/8 and 1/10-scale vehicles
3C charge rating for quick, safe recharging
Hard plastic case for increased durability and reliability
One year limited warranty beginning at date of purchase
Reaction 2.0
Dynamite's new Reaction 2.0 batteries come with all the power and performance you've come to expect from the original Reaction line, but now include a QR code directly on the battery label. You can scan the QR with the Dynamite Dashboard Smart Phone App for even quicker and easier setup. In addition, all Reaction 2.0 hardcase batteries now come in a sleek black color to better match whatever setup you use them in.
DYNB6223, 7.4V 600mAh 2S 20C LiPo EC3
Product Specifications
Battery Capacity
300-999mAh
Battery Type
LiPo (3.7V per cell)
Battery Voltage
7.4V
Connector Type
EC3
Part Type
Electronics
DYNB65021H2, Dynamite Reaction 2S 20C Hard Case LiPo Battery w/EC2 Connector (7.4V/650mAh)
This is a Dynamite RC 7.4V 650mAh Reaction 2S 20C Hard Case LiPo Battery with EC2 Connector. The EC2 equipped DYNB65021H2 LiPo battery is a direct replacement for the battery included with the Losi Mini T 2.0 (LOS01015T1, LOS01015T2, LOS01015T3).
Features:
Value-priced without sacrificing quality or performance
Pre-wired with an EC2 connector and JST-XH balance connector
Hard case design
Designed to fit Losi Mini-T 2.0 vehicles
Specifications:
Height: 0.8" (20 mm)
Length: 2.3" (58 mm)
Width: 1.2" (30 mm)
Weight: 1.7 oz (48g)
This product was added to our catalog on March 18, 2021
EFLB2802S30, E-flite 2S LiPo Battery 30C (7.4V/280mAh) w/UMX Connector
E-flite 2S, 280mAh, 30C Li-Poly Battery Pack. This battery is compatible with a variety of E-flite UMX 2S applications and is a great high power upgrade.
Specifications:
Type: LiPo
Capacity: 280mAh
Voltage: 7.4V
Number of Cells: 2
Weight: 0.6 oz (16.9g)
Configuration: 2S1P
Length: 1.5 in (39mm)
Width: 0.8 in (20mm)
Height: 0.5 in (13mm)
Application: UMX 2S Airplanes
Maximum Continuous Discharge : 30C
Maximum Continuous Current : 8.4A
Charge Protection Circuitry: No
Is Assembly Required: No
This product was added to our catalog on December 30, 2021
ELCNITRIDE110, Elceram Nitride 1/10 Brushless ESC w/LCD Display
Features:
A color display with Thin-Film-Transistor (TFT) LCD (Liquid-Crystal Display) technology, with a resolution of 160x80 pixels.
Self-diagnostic before the race: motor temperature, sensor cable, battery
Post-race data evaluation
Race data logging
Fully programmable all through the ESC without the need for a program card or wireless module
Realtime Data monitoring of the battery voltage, ESC, and motor temperatures
Advanced Aluminum Nitride Ceramic Cooling Technology
Extremely low internal resistance based on silver conductive layer
70% weight bias at the bottom of the esc
32-Bit MCU
13AWG Wires
This product was added to our catalog on November 12, 2023
Replacement 0802 II 15000kv Motor for Tinyhawk 3 with connector.
This moto can be used on other 1-2S builds!
Check out the rest of the Tinyhawk line and all our EMAX gear!
Includes
EMAX 0802 II 15000Kv Micro Motor for Tinyhawk III
Emax has entered the world of Express LRS products with its Aeris Link module. Available in both 915MHz or 2.4GHz for the best range and penetration! This module also features tons of output power and external power options, Choose Emax to feel confident in the skies using ELRS!
Check out all our ExpressLRS compatible gear, and our Emax Products!
Features
1000mW for 2.4GHZ ELRS
RGB fan displays battery level
OLED screen and joystick or LUA script friendly
2-5S operational voltages
Specifications
Module Bay Input Voltage: 5-12V
OLED Screen size: 1.29 " (Full size only)
OLED Screen resolution: 64 x 128 (Full size only)
Operating frequency: 2.4GHz ISM / 915MHz FCC
Output power: 10mW/25mW/50mW/100mW/250mW/500mW/1000mW
Refresh rate: 50Hz/100Hz/150Hz/250Hz/500Hz
Antennas: Moxon Directional Antenna (2.4GHz), RP-SMA connection
Configuration: Support signals of Crossfire Serial Data Protocol (CRSF) and OpenTX remote control
Interface: Type-C, JR interface
External Power: XT30 supporting 5-21V (2-5S) voltage input, 2S (8.4V) is recommended
Includes
1x Emax Aeris Link ELRS 2.4GHz Transmitter Module
Emax has entered the world of Express LRS products with its Aeris Link module. Available in both 915MHz and 2.4GHz for the best range and penetration! This module also features tons of output power and external power options, Choose Emax to feel confident in the skies using ELRS!
Check out all our ExpressLRS compatible gear, and our Emax Products!
Features
1000mW+ for 915MHz ELRS
RGB fan displays battery level
OLED screen and joystick or LUA script friendly
2-5S operational voltages
Specifications
Module Bay Input Voltage: 5-12V
OLED Screen size: 1.29 " (Full size only)
OLED Screen resolution: 64 x 128 (Full size only)
Operating frequency: 2.4GHz ISM / 915MHz FCC
Output power: 10mW/25mW/50mW/100mW/250mW/500mW/1000mW+
Refresh rate: 50Hz/100Hz/150Hz/250Hz/500Hz
Antennas: Moxon Directional Antenna (2.4GHz), RP-SMA connection
Configuration: Support signals of Crossfire Serial Data Protocol (CRSF) and OpenTX remote control
Interface: Type-C, JR interface
External Power: XT30 supporting 5-21V (2-5S) voltage input, 2S (8.4V) is recommended
Includes
1x Emax Aeris Link ELRS 900MHz Transmitter Module
All items with batteries must be shipped by a ground shipping method.
The TinyHawk 2 RTF kit has everything you need to enjoy micro flight, all packed into a handy carrying case! This is truly the ideal way to try out FPV!
2 batteries are included (a 1S and a 2S), but if you want to maximize your air time, we recommend picking up a few of the following RDQ Series LiPos:
1S 450mAh - PH2.0
2S 300mAh - PH2.0
Check out our other RTF combos, all our pre-built quads, all things Tinyhawk, and our EMAX selection!
Specifications
Frame
Wheelbase: 75mm
Dry Weight: 31.2g
All Up Weight: 43.5g with 1x 450mAh 1S battery
Frame Material: Polypropylene
Motors
Stator Size: 0802
Kv: 16000kv
Propeller Mount: Push-On Avan TH-style
Propeller: Avan Turtlemode 4-Blade
All-In-One (AIO) Flight Controller
Flight Controller: F4 (MATEKF411RX Firmware)
ESC: 4-in-1 5A BlHeli_S
Receiver: EMAX SPI Receiver (Compatible with FrSky D8 mode)
Battery Connector: JST-PH2.0
FPV System
VTX Power: 25/100/200mw Switchable
Channels: 37CH incl. Raceband
Camera: RunCam Nano 2 1/3" 700TVL CMOS
Smart Audio Connected
Includes
1x Tinyhawk II FPV Racing Drone
1x EMAX Transporter 5.8G FPV Goggles
1x EMAX Transporter 18650 Goggle Battery Pack w/ USB Charging
1x EMAX E6 Transmitter
1x EMAX 450mAh 1S HV Battery
1x EMAX 300mAh 2S HV Battery
2x CCW + 2x CW Spare Props
1x 1S-2S USB LiPo Charger
1x Screwdriver + Hardware Kit
1x Micro USB Charging Cable
1x Faux Carbon Fiber Carrying Case
Replacement all-in-one flight controller and ESC for the Tinyhawk 3. Standard 26x26 whoop mounting pattern for DIY builds.
Check out the rest of the Tinyhawk line and all our EMAX gear!
Includes
1x EMAX Tinyhawk III 1-2S F4 AIO Flight Controller 5A ESC 25/100/200mW VTX
ERC8-DC-1035, Exclusive RC Non Functional Drag Racing Parachute (Black)
The Exclusive RC Non Functional Drag Racing Parachute is an accurately scaled down replica of a 1:1 drag racing parachute. Manufactured with real chute bag material, and an included chute tag, this is a great way to finish off the back end of your street eliminator/no prep car. Available in multiple colors.
Installation requires the Exclusive RC Drag Chute Mount (not included). A variety of mounts are available to mount various body types and styles.
Specifications:Dimensions:Length: 30mmWidth: 30mmHeight: 30mm
This product was added to our catalog on February 2,2024
