Brushless Motors
-
![TRA3350R, Traxxas VXL-3S Velineon Brushless Power System Combo (Waterproof)]()
Traxxas TRA3350R, Traxxas VXL-3S Velineon Brushless Power System Combo (Waterproof)
TRA6814, Traxxas VXL-3S Velineon Brushless Power System Combo (Waterproof) The next generation of extreme brushless horsepower is here, Ready-To-Race® from Traxxas—and now waterproof! Velineon™ is the ultimate brushless system delivering the tire melting horsepower, supercharged speeds, and ease of use that you expect from Traxxas. Just plug it in and it works. The key to the Velineon’s extreme power output is total system optimization. Each component, from the Traxxas high-current battery connector, to the powerful Velineon 3500 brushless motor, is carefully engineered to work with other system components to eliminate restriction and allow maximum power flow. High-frequency transistors and advanced circuit design delivers incredibly smooth and refined throttle control. The Velineon system accepts the widest range of battery types, including 3-cell Lithium Polymer packs (3S LiPo packs). Built-in low-voltage detection in the VXL-3s electronic speed control helps keep LiPo battery packs in top condition. Traxxas’ exclusive waterproof technology allows the Velineon system to operate in wet conditions, including mud and snow, with no special precautions required. You decide where the Velineon powered adventure leads—the only limits are your imagination. Key Features: Now Waterproof Compatible with brushed, brushless and sensored brushless motors Auto-detects the motor type Accepts NiCad, NiMH (4-10 cells), and LiPo (2-3cells) battery packs Built-in-two-stage low-voltage detection for LiPo battery packs 3 drive profiles:Sport Mode, Race Mode, and Training Mode Two-Stage Thermal shutdown protection Velineon 3500 Brushless Motor 10-Turn, 3500kV Optimized for extreme power and efficiency in 1/10 vehicles This product was added to our catalog on May 7, 2021
$169.99
-
![TRA3351R, Traxxas Velineon 3500 Brushless Motor (10T/3500kV)]()
Traxxas TRA3351R, Traxxas Velineon 3500 Brushless Motor (10T/3500kV)
TRA3351R, Traxxas Velineon 3500 Brushless Motor (10T/3500kV) This is the Traxxas Velineon 3500 Brushless Motor. The Velineon 3500 Brushless Motor features a precision balanced rotor, high-speed ball bearings, and ultra high-temperature Neodymium magnets for a great blend of power and long-life. The Velineon 3500 delivers consistent, high-power output, run after run. Features: Ultra high-temperature sintered Neodymium magnets provide massive torque and linear power Optimized for power and efficiency in 1/10th scale vehicles Consistent, high-power output, run after run Low-maintenance, unique Traxxas design Efficient, high-speed ball bearings Low maintenance design Precision-balanced rotor Protective end cap 10-Turn, 3500Kv Rebuildable Hex hardware Brilliant blue-anodizing finish Silicon steel laminations Delivers more power than comparable brushed motors Note: The motor is not compatible with the older TRA3355X ESC. It must be used with the newer TRA3355R ESC. This product was added to our catalog on May 8, 2021
$89.99
-
![CSE010015504, Castle Creations Mamba X 1/10 Brushless Combo w/1406 Sensored Motor (7700kV)]()
Castle Creations CSE010015504, Castle Creations Mamba X 1/10 Brushless Combo w/1406 Sensored Motor (7700kV)
CSE010015504, Castle Creations Mamba X 1/10 Brushless Combo w/1406 Sensored Motor (7700kV) The Castle Creations Mamba X 1/10 Brushless Combo includes the Mamba X, with the awesome 1406 Sensored motor to create a all in one system perfect for 1/10 scale on-road cars using 2S, lightweight - conservatively geared stadium trucks and buggies that want the ultimate in speed. The motor included in this combo is NOT recommended for use in 2WD or 4WD short course trucks. The Mamba X is going to shake things up. Extremely versatile, and capable of powering a wide variety of applications and vehicles the Mamba X is ideal for racing at the track with your 2wd buggy, bashing through mud puddles in your monster truck, or navigating a hardcore trail with your crawler. The high performance Mamba X includes an integrated and powerful 8A adjustable BEC and can push the most extreme 1/10th scale setups and 1/8th scale race buggies. Castle Creations 1406 Sensored 4-Pole Brushless Motors combine rotor position sensor technology with an improved high power and high efficiency motor design to deliver ultra smooth startup, precise low speed control, predictable power delivery, incredible torque, and lightning fast response. Through the use of Castle's Smart Sense technology, the position of the rotor is always known by the ESC. This eliminates the possibility of encountering cogging or inconsistency during startup, and allows the 1406 to deliver PRECISE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for. Features: ESC Wide 2S to 6S input voltage range Sensored Motor Support (Castle X-Series Sensor Harness Included) Waterproof 8A Adjustable BEC (5.25V-8.0V) Data-logging Rugged CNC Aluminum Case Castle Link Programming Support SmartSense™ Integrated Capacitors Removable 30mm Cooling Fan Integrated 4mm Bullet Connectors 12 AWG Power Wires Waterproof Switch Audible Alerts The Mamba X is proudly designed and manufactured in Olathe, Kansas Backed by Castle Creations’ 1-year warranty and unparalleled "make-it-right" customer support Motor 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 13 AWG high strand wire with silicone insulation Kevlar wrapped rotor 6061-T6 Billet aluminum heatsink can High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: ESC Input Voltage Range: 2S LiPo (7.4V) to 6S LiPo (25.2V) BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes Cooling Fan: Yes, factory equipped (30mm), fully removable** (see Product Use Statements below) Size (LxWxH): 2.14x1.39x1.18" (54.4x35.2x30.0mm) Weight (with wires): 3.56 oz. (101g) Connectors: 4.0mm female bullets for motor connection. Items Needed for Operation: Battery Connector Application Guidelines: Intended for up to 6S (25.2 Volt) operation in vehicles weighing less than 9bs/4kg Recommended Motors: Castle 1406, 1410 and 1415 Sensored motors Max. Recommended Vehicle Weight: Less than 9bs/4kg, with batteries, ready-to-run Telemetry Link Capable: Yes Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free link included in package) and freely downloadable Castle Link Windows software. Motor Input Voltage Range: 2S LiPo Kv: 7700 Max. RPM: 100,000 Length: 49.5mm Diameter: 36mm Weight (w/wires): 189 g / 6.7oz Shaft Size: 15mm Diameter: 1/8" (3.17mm) Mounting Hole Specifications: M3 @ 25mm Cooling Fan: Optional - Coming Soon Connectors: 4mm male Castle Bullet Connectors Application Guidelines: 1:10 scale on-road cars using 2S, lightweight stadium truck and buggies geared conservatively. Not for use in 2WD or 4WD short course trucks. Recommended ESC(s): Mamba Max Pro Max. Recommended Vehicle Weight: Vehicles up to 4lbs. Tech Notes: Running modes: SMARTSENSE™, Sensored, Sensorless Product Use Statements: *Although Mamba X is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC and motor with clean water after exposure to corrosives or dirt. While the motor and controller may be waterproof, Castle suggests users confirm that the rest of their vehicle, including the batteries, servos, radio and chassis are also waterproof before exposing them to liquids of any kind. **The cooling fan must be removed prior to driving in wet conditions. It is not waterproof. Tech Notes: Mamba X setups frequently hit 100+ amps in peaks and not all LiPos are created equal. Surge ratings should never be used to determine a pack's suitability for a brushless application. Recommended battery capacity for 1:10th and 1:8th scale vehicles is 5000mAh. We recommend using 30C continuous discharge or higher LiPo batteries (or high quality 25C batteries such as Traxxas® Power Cell). Our experience suggests using only mild gear ratios with NiMH cells. Do not attempt to use NiMH cells in extreme setups. Applying voltages higher than 25.2V will cause irreparable damage to ESC. We recommend a high-current connector designed for high-powered electric systems, rated for 70+ amps. Invest in connector sets made for high-powered electric systems such as our Castle 6.5mm Polarized Connectors, Castle 4.0mm Polarized Connectors, Traxxas® Power Connectors, or Deans® Ultra Plugs This product was added to our catalog on May 3, 2021
$274.95
-
![SPMXSEM0501, Spektrum RC Firma Brushless Motor/ESC 2-in-1 Combo (6000Kv)]()
Spektrum SPMXSEM0501, Spektrum RC Firma Brushless Motor/ESC 2-in-1 Combo (6000Kv)
SPMXSEM0501, Spektrum RC Firma Brushless Motor/ESC 2-in-1 Combo (6000Kv) This is the Spektrum RC Firma Brushless Motor/ESC 2-in-1 Combo. This powerful brushless combo is an excellent drop in brushless system for Mini vehicles such as the Losi Mini-T, Mini-B and Mini JRX2. This system contains a high-torque and high speed 6000kv brushless sensorless motor that is designed for bashing and sport racing applications. The motor features the same basic dimensions and mounting patterns as industry-standard, 1/16 to 1/18, 280-size brushed motors, making it easy to install and setup. These motors also offer high performance over a longer lifetime with little to no maintenance. Features: Drop-in brushless upgrade for Losi Mini-T, Mini-B and Mini JRX2 Integrated 20 amp ESC 2-in-1 design reduces space requirements EC2 connector that is compatible with popular battery types used in 1/18th scale models Perfect upgrade for brushed 280 motors with the same diameter Industry standard mounting hole patterns High torque and high RPM 6000kv Brushless Sensorless motor Counter-clockwise operation only Easy programming via one-button interface High-quality construction with ball bearings Hardened steel 2mm motor shaft Low maintenance design Easy installation Specifications: Input Voltage: 2S LiPo RPM/Volt (Kv): 6000 Motor Type: Brushless Maximum Burst Current: 40A Maximum Continuous Current: 20A Connector Type: EC2 BEC: Yes BEC Type: Switching BEC Continuous Current: 1A Motor Design: Inrunner Reverse: Yes Forward: Yes Auto Cutoff: Yes Overload Protection: Yes Shaft Diameter: 0.07" (2mm) Outer Diameter: 0.94" (24mm) Product Length: 1.41" (36mm) Includes: (1) Firma Brushless Motor/ESC 2-in-1 Combo (6000Kv) (1) Product Manual This product was added to our catalog on December 12, 2022
$84.99
-
![HWI30120402, Hobbywing QuicRun Fusion Pro FOC 2-in-1 ESC & Motor System (2300Kv)]()
HobbyWing HWI30120402, Hobbywing QuicRun Fusion Pro FOC 2-in-1 ESC & Motor System (2300Kv)
HWI30120402, Hobbywing QuicRun Fusion Pro FOC 2-in-1 ESC & Motor System (2300Kv) The Hobbywing QuicRun Fusion FOC 2300Kv 2-in-1 ESC & Motor System is a unique ground-up design, packed with technology specific for scale trucks and rock crawlers. Features: Integrated design of Hobbywing's patent technology: The integrated design of the ESC makes the size similar to a 540 motor, and the overall weight is only 209g. This makes the layout and wiring of the car simpler, while creating a cleaner overall chassis that also leaves more room for an interior. Intelligent Torque Output & Speed Closed-loop Control for Easy Control: The Fusion system combined with Intelligent Torque output and closed-loop speed control means the power system will maintain the motor’s Torque level and RPM as the vehicle conditions change. Uphill, downhill, under load, the intelligent output torque makes the operation more consistent. Note: If the “RPM/Throttle Matching” is set to “Disabled”, no intelligent torque output & speed closed-loop control, just like the brushed system. FOC (Field-oriented Control) for Super Linearity & HighTorque & Extreme Mute: The Fusion system adopts FOC driving mode so low speed torque is strong, and it runs smoothly at very low speed. Moreover, the motor is extremely silent when it is running. The driving noise which annoys the driver disappears. It is the best choice for a scale rock crawler. Waterproof: Applicable to All Weather & Track Conditions: The IP-67 waterproof system has excellent waterproof and dustproof performance. You can easily drive in the mud, sand, ice, snow and water. High Driving Efficiency for Long Battery Life: FOC offers high efficiency and reduced heat, dramatically extending runtime. Benefitting from a sine wave driving mode, the motor runs silently and softly. Professional Drag Brake Adjustments & Super Parking Capacity: 8 levels of drag brake force and 9 settings of drag brake rate allow a high level of tuning for different conditions and driver preference. The maximum drag brake force is about twice that of an ordinary brushless system of the same size, providing super strong parking capacity on a steep slope. Advanced and Secure Electronic Switch: Compared to standard on/off switches, the dust, dirt, and waterproof electronic switch housing ensures a long reliable life for your power system, and will not suffer from the problems that will damage a mechanical switch. Specifications: Motor Kv: 2300Kv Continuous Current: 60A Shaft Diameter: 3.175mm Peak Current: 200A Input Voltage: 2-3S LiPo/6-9 Cell NiMH BEC Output: 6V/7.4V adjustable, 4A continuous (switch mode) Input Wires: 14awg, 330mm long Input Connectors: XT60 (factory installed) Port Programming: Independent programing interface (switch position) Size: 37x58mm Weight: 209g w/wires Includes: (1) FOC motor w/ built-in ESC & Factory installed XT60 plug This product was added to our catalog on June 1, 2022
$169.99
-
![TRA3370, Traxxas Velineon VXL-3M Waterproof 1/16 Scale Brushless Power System]()
Traxxas TRA3370, Traxxas Velineon VXL-3M Waterproof 1/16 Scale Brushless Power System
TRA3370, Traxxas Velineon VXL-3M Waterproof 1/16 Scale Brushless Power System Fits: Traxxas 1/16 E-Revo Traxxas 1/16 Mustang Traxxas 1/16 Race Truck Traxxas 1/16 Rally Traxxas 1/16 Slash Traxxas 1/16 Summit This is the Traxxas Velineon® VXL-3m forward/reverse brushless electronic speed control/Velinion 380 motor combo, and is intended for use with 1/16 scale vehicles. The Velineon ESC simplifies brushless technology with easy, built-in profiles and intuitive programming. The VXL-3m™ uses advanced circuit design that allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. It sets up, operates, and programs just like the Traxxas XL-5™ family of ESCs so there's no tricky new procedures to learn. Traxxas' exclusive patent-pending Training Mode™ is also included to limit full throttle to 50% for young or inexperienced drivers. For the most advanced users, the VXL-3m is equipped with two-stage low voltage detection to allow LiPo battery use, including powerful 11.1-volt 3S packs! The Velineon® 380 Brushless Motor uses ultra high-temperature Neodymium magnets, high-speed ball bearings, and a precision balanced rotor for big power and long-life. Since there are no brushes or commutator to wear out, the need for maintenance is virtually eliminated. The Velineon 380 delivers consistent, high-power output, run after run. Velineon VXL-3m Features: Traxxas High-Current Connector maintains pure, unrestricted power flow from the battery to the brushless power system. Built-in two-stage low voltage detection for Lithium Polymer (LiPo) battery use provides a clear signal to the driver that the battery pack is nearing its minimum voltage threshold. Wide range of battery options, including 6-12 cell NiMH or NiCad packs The patent-pending Training Mode™ is an exclusive Traxxas feature that reduces the overall power output of the VXL-3m by 50%, making it easier for new or younger drivers to control their model. When they're ready, simply change profiles to unleash full-throttle action. Advanced circuit design allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. There's no need for additional sensor wiring and hardware complexity. The EZ-Set® push-button setup operates and programs just like other Traxxas speed controls such as the XL-5. This eliminates the need to learn a new set of procedures. The VXL-3m is programmable with three drive profiles: Sport Mode – Fwd / Brake / Rev Race Mode – Fwd / Brake Training Mode™ – 50% Fwd / Brake / 50% Rev Multi-color LED provides clear feedback Two-stage thermal shutdown protection protects the VXL-3m from overheating. Locked Rotor Protection™ prevents system damage by cutting power if the vehicle is stuck or the motor is bound. Battery Over-Voltage Protection™ causes the ESC to go into failsafe mode if the maximum input voltage is exceeded. Water resistent case design uses rubber seals and o-rings to protect against damage caused by water and moisture. Micro-fin aluminum heatsink dissipates heat. MOSFET design provides high-current output (326 amp peak) with incredibly low resistance (.0005 (Ohm)). Gold plated 3.5mm bullet connectors on 16-gauge Maxx® Cable flow full power to the motor without performance-strangling resistance. Velineon 380 Features: Ultra high-temperature sintered Neodymium magnets provide Massive torque and linear power Optimized for power and efficiency in 1/16th scale vehicles Consistent, high-power output, run after run Low-maintenance, unique Traxxas design Efficient, high-speed ball bearings Precision-balanced rotor 8-Turn, 4000KV Rebuildable Hex hardware Brilliant blue-anodized finish Silicone steel laminations Delivers more power than comparable brushed motors VXL-3M Specifications: Input Voltage: 6 to 12 cells NiMH, 2S to 3S LiPo Case Size: 26.5mm W x 46.5mm D x 22mm H Weight: 38 grams Motors: Sensorless Brushless Motor Limit: None On Resistance: 0.0005 Ohms PWM Frequency: 12,000Hz Peak Current: 326A Continuous Current: 52A BEC Voltage: 6.0V DC Motor / Battery Wiring: 16-Gauge Maxx® Cable Transistor Type: MOSFET Low Voltage Detection: 2-Stage indicators, switchable (on or off) Thermal Protection: 2-Stage thermal shutdown Single-button setup: Yes, Traxxas EZ-Set® Battery Input Connector: Traxxas High-Current Connector Motor Connector: TRX 3.5mm Bullet Connectors Velineon 380 Specifications: Type: Sensorless Brushless kV (RPM/Volt): 4000kV (8T) Magnet Type: High Temp Sintered Neodymium Connection Type: TRX 3.5mm Bullet Wire Size: 16g Maxx Cable Continuous Current: 25A Max Current: 50A Burst Max RPM: 50,000 Weight: 140g (4.94oz) This product was added to our catalog on May 7, 2021
$149.99
-
![83076-4, Traxxas 4-Tec 2.0 VXL 1/10 Brushless RTR Touring Car Chassis (NO Body) w/TQi 2.4GHz Radio & TSM]()
Traxxas 83076-4, Traxxas 4-Tec 2.0 VXL 1/10 Brushless RTR Touring Car Chassis (NO Body) w/TQi 2.4GHz Radio & TSM
83076-4, Traxxas 4-Tec 2.0 VXL 1/10 Brushless RTR Touring Car Chassis (NO Body) w/TQi 2.4GHz Radio & TSM 1/10 Scale 4-Tec 2.0 VXL AWD Chassis - Brushless! The 4-Tec 2.0 VXL chassis provides the ultimate high speed driving experience. The high-tech chassis keeps weight positioned as low as possible for a crisp, responsive feel. The modular interlocking design allows easy maintenance while providing unprecedented rigidity and tight tolerances. The waterproof VXL-3s electronic speed control channels massive power to the Velineon brushless motor for four wheel tire-spinning acceleration and incredible 70+mph* top speed. A finely tuned suspension keeps the wheels glued to the pavement and Traxxas Stability Management® (TSM) provides lightning-quick corrections to keep you in control. Grab the transmitter, rip full throttle, and hold on! The Traxxas 4-Tec 2.0 VXL delivers a high speed thrill ride like you’ve never experienced. Class-Leading Brushless Power The 4-Tec 2.0 VXL’s Velineon brushless power system defines a whole new generation of outrageous electric power that doesn't know limitations and boundaries. Pour in the voltage and out comes the speed in tidal waves of force harnessed by precision throttle control. For the uninitiated, prepare yourself... the sheer brutal power combined with the 4-Tec 2.0 VXL chassis’ four-corner grip results in tire-melting acceleration and lightning fast speed. The Velineon 3s brushless power system features system components that work together as an optimized package, from the patented Traxxas High-Current connector to the custom-wound motor. It's engineered together from the start to deliver the ultimate in efficiency, speed, and run-time along with precision throttle response and refined control. It's brushless performance the Traxxas way: wicked fast and easy to use. Just plug it in and it works, no special knowledge or programming skills required. Features: Adjustable chassis accepts standard 200mm bodies Shaft-driven full-time all-wheel drive system TQi 2.4GHz radio system with Traxxas Stability Management (TSM) Waterproof electronics for all-weather, all-season R/C excitement Velineon brushless power system Adjustable steel turnbuckles and steering links Low-CG fiber-composite monocoque chassis with high approach angle front bumper Race-proven sealed differentials VXL-rated high-speed Response tires Specifications: Length: 14.94 Inches (379mm) Front Track: 7.7 Inches (196mm) Rear Track: 7.9 Inches (200mm) Center Ground Clearance: 0.3 Inches (9mm) Weight: 2.81lbs (1.28kg) Height (overall): 2.43 Inches (62mm) Wheelbase: 10.1 Inches (256mm) Shock Length: Short (front and rear) Tire Diameter: 2.6 Inches (66mm) Tire Width (front): 1.0 Inches (26mm) Tire Width (rear): 1.2 Inches (30mm) Wheel Diameter: 2.1 Inches (53mm) Speed Control Type: VXL-3S Motor (electric): Velineon 3500 Brushless Overall Drive Ratio: 6.87 Differential Type: Hardened Steel Bevel, Sealed, Limited Slip Gear Pitch: 48 Chassis Structure/Material: Molded Tub / Nylon Composite Drive System: Shaft-Driven, Direct Drive 4WD Steering: Dual-Bellcrank Radio System: TQi 2.4GHz Radio with TSM Receiver Skill Level: 3 Top Speed: 70+mph* Battery Tray: 158mm long / 46mm wide / 23 or 26mm high Required Items (Sold Separately): 4 "AA" Batteries (for transmitter), Charger, 6 or 7-Cell NiMH or 2-cell LiPo Battery *With optional gearing and 3S LiPo battery (items sold separately) Needed To Complete: 200mm Touring Car Body 6 or 7-cell NiMH Battery Pack, or 2S or 3S LiPo Battery Pack w/Traxxas Connector Compatible Battery Charger (4) "AA" Batteries (For transmitter) This product was added to our catalog on April 24, 2021
$399.99
-
![CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft)]()
Castle Creations CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft)
CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft) The Castle Creations Mamba X SCT Waterproof 1/10 Brushless Combo includes the Mamba X, with the awesome 1415 Sensored motor to create a all in one system perfect for 2WD and 4WD Short Course trucks weighing up to 6.5lbs running on a 3s or 4s LiPo. The Mamba X is going to shake things up. Extremely versatile, and capable of powering a wide variety of applications and vehicles the Mamba X is ideal for racing at the track with your 2wd buggy, bashing through mud puddles in your monster truck, or navigating a hardcore trail with your crawler. The high performance Mamba X includes an integrated and powerful 8A adjustable BEC and can push the most extreme 1/10th scale setups and 1/8th scale race buggies. Castle Creations 1415 Sensored 4-Pole Brushless Motors combine rotor position sensor technology with an improved high power and high efficiency motor design to deliver ultra smooth startup, precise low speed control, predictable power delivery, incredible torque, and lightning fast response. Through the use of Castle's Smart Sense technology, the position of the rotor is always known by the ESC. This eliminates the possibility of encountering cogging or inconsistency during startup, and allows the 1406 to deliver PRECISE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for. Features: ESC Wide 2S to 6S input voltage range Sensored Motor Support (Castle X-Series Sensor Harness Included) Waterproof 8A Adjustable BEC (5.25V-8.0V) Data-logging Rugged CNC Aluminum Case Castle Link Programming Support SmartSense™ Integrated Capacitors Removable 30mm Cooling Fan Integrated 4mm Bullet Connectors 12 AWG Power Wires Waterproof Switch Audible Alerts The Mamba X is proudly designed and manufactured in Olathe, Kansas Backed by Castle Creations’ 1-year warranty and unparalleled "make-it-right" customer support Motor 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 13 AWG high strand wire with silicone insulation Kevlar wrapped rotor 6061-T6 Billet aluminum heatsink can High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: ESC Input Voltage Range: 2S LiPo (7.4V) to 6S LiPo (25.2V) BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes Cooling Fan: Yes, factory equipped (30mm), fully removable** (see Product Use Statements below) Size (LxWxH): 2.14x1.39x1.18" (54.4x35.2x30.0mm) Weight (with wires): 3.56 oz. (101g) Connectors: 4.0mm female bullets for motor connection. Items Needed for Operation: Battery Connector Application Guidelines: Intended for up to 6S (25.2 Volt) operation in vehicles weighing less than 9bs/4kg Recommended Motors: Castle 1406, 1410 and 1415 Sensored motors Max. Recommended Vehicle Weight: Less than 9bs/4kg, with batteries, ready-to-run Telemetry Link Capable: Yes Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free link included in package) and freely downloadable Castle Link Windows software. Motor Input Voltage Range: 3-4S LiPo Kv: 2400 Max. RPM: 75,000 Length: 69.5mm Diameter: 36mm Weight (w/wires): 319g / 11.3oz Shaft Length: 21mm Shaft Diameter: 0.197" (5mm) Mounting Hole: M3 @ 25mm Cooling Fan: Optional, coming soon! Connectors: 4mm male Castle Bullet Connectors Recommended ESC (s): Combo includes Mamba X ESC. Recommended Applications: 2WD and 4WD Short Course trucks weighing up to 6.5lbs running on a 3s or 4s LiPo with included 1415 - 2400kv sensored motor. Running Modes: SMARTSENSE™, Sensored, Sensorless Product Use Statements: *Although Mamba X is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC and motor with clean water after exposure to corrosives or dirt. While the motor and controller may be waterproof, Castle suggests users confirm that the rest of their vehicle, including the batteries, servos, radio and chassis are also waterproof before exposing them to liquids of any kind. **The cooling fan must be removed prior to driving in wet conditions. It is not waterproof. Tech Notes: Mamba X setups frequently hit 100+ amps in peaks and not all LiPos are created equal. Surge ratings should never be used to determine a pack's suitability for a brushless application. Recommended battery capacity for 1:10th and 1:8th scale vehicles is 5000mAh. We recommend using 30C continuous discharge or higher LiPo batteries (or high quality 25C batteries such as Traxxas® Power Cell). Our experience suggests using only mild gear ratios with NiMH cells. Do not attempt to use NiMH cells in extreme setups. Applying voltages higher than 25.2V will cause irreparable damage to ESC. We recommend a high-current connector designed for high-powered electric systems, rated for 70+ amps. Invest in connector sets made for high-powered electric systems such as our Castle 6.5mm Polarized Connectors, Castle 4.0mm Polarized Connectors, Traxxas® Power Connectors, or Deans® Ultra Plugs This product was added to our catalog on February 16, 2021
$292.95$275.00
-
![KYO34492T1, Kyosho EP Fazer Mk2 FZ02L VE 1970 Dodge Charger Supercharged ReadySet (Grey) w/Syncro KT-231P+ Radio]()
KYOSHO KYO34492T1, Kyosho EP Fazer Mk2 FZ02L VE 1970 Dodge Charger Supercharged ReadySet (Grey) w/Syncro KT-231P+ Radio
KYO34492T1, Kyosho EP Fazer Mk2 FZ02L VE 1970 Dodge Charger Supercharged ReadySet (Grey) w/Syncro KT-231P+ Radio Kyosho Fazer Mk2 FZ02L VE Brushless Touring Car with Supercharged 1970 Dodge Charger Body The Kyosho EP Fazer Mk2 FZ02L VE 1970 Dodge Charger Supercharged ReadySet is a brushless chassis that has a classic muscle car look. The combination of a beautifully reproduced body with the FAZER series chassis can’t be beaten. This Charger body features a scale supercharger and molded light buckets for optional LED's (not included). To complete the look, Kyosho included functional flip headlight covers that can actuate by removing a screw from the headlight assembly. Featuring front & rear gear differentials, oil shocks and full ball bearing specs, the high durability and impact resistance allows drivers to unleash the full potential of the chassis. Brake disc wheel hubs with two different offsets (0mm, +5mm) provide compatibility with 190mm and 200mm width body styles and allows the wheelbase to be adjusted to 260mm by replacing some parts (not included) for compatibility with other 1/10 scale body styles, in addition to the included body. The symmetrical chassis design synergizes excellent front-rear balance through the suspension with responsive control, regardless of the power source. The Ready Set package comes fully assembled and requires only charger and battery for the chassis, and batteries for the transmitter to start driving. Features: “Ultra Scale Body” replicates the fine details of the actual body of the car. Shaft drive full-time 4WD touring chassis (FZ02) Factory-assembled Readyset package only requires 4 x AA alkaline batteries for the transmitter, and battery with charger for the chassis Equipped with 2-bevel grease-filled gear diffs on front and rear Large size dog bones and cup joints realize superior reliability and durability Belt mounting battery compartment allows various battery types to be used Full ball bearings that reduce drive loss equipped throughout the drive system Includes completely finished body with color scheme and decals applied Sealed differential and transmission deliver reliable performance, even on dusty parking lot surfaces Performance can be further enhanced by installing various optional parts Specifications: Length: 507mm Width: 195mm Body Width: 210mm Height: 128mm Chassis Height: 15mm Wheelbase: 274mm Tread (F/R): 167mm Tires (F/R): 64×27.7mm Gear Ratio: 6.54:1 Weight: 1680g Includes: Completed chassis with R/C radio installed Factory assembled body complete with color scheme Syncro KT-231P+ transmitter Hexagonal wrench Spanner Needed to Complete: (4) AA batteries for transmitter 7.2-7.4V Battery for chassis Charger for battery for chassis Tools This product was added to our catalog on May 9, 2022
$329.99
-
![CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor]()
Castle Creations CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor
CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor The Castle Creations Mamba XLX 2 1/5 Scale Sensored Brushless ESC/Motor Combo with 2028 800Kv motor is a product guaranteed to redefine the limits of large scale R/C. Though it shares the name of its predecessor, the Mamba XLX, this is an ESC that lives in a class of its own. Reengineered from the ground up, the Mamba XLX 2 is packed with a potent combination of design, hardware and software advancements that will set a new standard for large-scale power systems. Designed for 1/5 Scale models weighing up to 42 lbs, the XLX 2 is an incredible power upgrade for the Losi DBXL-E and Super Rock Rey, Arrma Kraton 8S and Outcast 8S, or Traxxas X-Maxx models! If you are looking for the ultimate upgrade for your speed run, drag racing or off road rigs - the XLX 2 is a true heavyweight, with no contenders. CRYO-DRIVE: MORE POWER – COOLER TEMPS – LONGER RUNS Castle’s latest break-through technology, minimizes the amount of time the ESC’s electrical components spend generating heat. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 50mm fan and a forged elliptical fin heatsink, the design maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling. NOTE: Some vehicles may require aftermarket parts to allow ESC and/or motor fitment. Features: Sensored, Sensorless and SmartSense™ running modes Powerful Integrated 20A Peak Adjustable BEC (5.25V-8.0V) Premium forged heatsink with for superior airflow and increased heat dissipation Oversized factory equipped thermally controlled 50mm fan Waterproof design for all weather conditions. ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the components and promote efficient heat transfer Data-logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for “on the-fly” adjustments using your transmitter Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options. Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store. Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1-year warranty Specifications: ESC: Input voltage range: 3S-8S LiPo Length: 3.98” (101.2mm) Width: 2.49” (63.3mm) Height: 2.2” (55.8mm) On/Off Switch: Yes, waterproof* Cooling Fan: Yes, thermally controlled factory equipped (50mm) fully removable** Weight: 13.1 oz (371g) Running Modes: Sensored, Brushed, Sensorless and SmartSense™ when paired with a Castle 4-POLE 12-SLOT Sensored Motor. (Dust cover included in package for non-sensored operation) Wire Gauge: 8AWG Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX, T7PXR Transmitters. Items Needed: Battery connectors designed for 150+ amps continuous, such as Castle 6.5mm polarized or CC BULLET 8.0MM Motor: Application Guidelines: 1:5th Scale vehicles weighing up to 30 lbs. Vehicle Examples: Losi DB XL-E,™ Losi Super Rock Rey™, Arrma Kraton 8s™, Arrma Outcast 8s™, Traxxas X-Maxx™ (Some vehicles may require aftermarket parts to allow ESC and/or motor fitment) Input Voltage Range: MIN: 3S LiPo, MAX: 8S LiPo 33.6V Kv: 800Kv Max. RPM: 45,000 Diameter: 2.22” (56.3mm) Length: 4.44” (112.7mm) Shaft Size: 30mm (Length), 8mm (Diameter) Weight (w/wires): 44 oz./1.25kg Mounting Hole Specifications: Holes: 4mm, Spacing: 30mm Connectors: 8.0mm male connectors, 300mm Direct Connect Sensor Wire Includes: Mamba XLX2 ESC 2028-800kv Sensored Brushless Motor 300mm Direct Connect Sensor Wire Mamba Decals Mamba XLX2 Quick Start Guide Sensor port dust cover Coupon for free Castle Link USB This product was added to our catalog on October 12, 2021
$499.99
-
![HWI38010801, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/4985SL (1650kV)]()
HobbyWing HWI38010801, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/4985SL (1650kV)
HWI38010801, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/4985SL (1650kV) The Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo includes the 4985SL 1/7 scale, 1650kV motor and is a great option for high-end, aggressively powered 3S - 6S builds. Specifications: Motor: Model: 4985SL-1650KV Pole: 4 KV (No-load): 1650KV Resistance: 0.0053 Ω Current (No-load): 5.4 A Max. Output Power: 5700 W Current at the point of M.O.P: 160 A Motor Diamter: 49mm Motor Length: 86.5mm Shaft Diameter: 5.0mm Shaft Length: 21.5mm LiPo Cells: 3-6 Weight: 587g (20.71oz) Applications: 1/6th & 1/7th RC Vehicles ESC: Continuous Current: 160A Peak Current: Peak Current: Peak Current: 1,050A Motor Type: Sensorless Brushless Motor Applications: 1/6th Touring Car, Buggy, Truggy and Truck Motor Limit: With 6S LiPo/18S NiMH: KV ≤1500 (5892 size motor); With 8S LiPo/24S NiMH: KV ≤1200 (5892 size motor) LiPo/NiMH Cells: 9-24S NiMH, 3-8S LiPo BEC Output: 6V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC) Cooling Fan: Powered by the stable BEC voltage of 6V/7.2V Connectors: Input End: None, Output End: Female 6.5mm Gold Connectors (pre-soldered onto the PCB of the speed controller) Size (LxWxH): 70x56x46.5mm Weight: 240g Programming Port: FAN /PRG Port This product was added to our catalog on April 21, 2021
$259.99
-
![TRA3352R, Traxxas VXL Velineon 3500 Brushless Motor Rebuild Kit]()
Traxxas TRA3352R, Traxxas VXL Velineon 3500 Brushless Motor Rebuild Kit
TRA3352R, Traxxas VXL Velineon 3500 Brushless Motor Rebuild Kit This is a Traxxas Motor Rebuild Kit for the VXL Velineon 3500 Brushless Motor. This is the updated kit, replacing the now discontinued TRA3352 rebuild kit. This rebuild kit includes one Velineon 3500 plastic endbell, two 5x11x4mm ball bearings, four 2.5x5mm BCS screws (with threadlock) and one rear bushing. This product was added to our catalog on May 7, 2021
$13.00
-
![TRA3483, Traxxas Sledge 77mm Brushless Motor (2000Kv)]()
Traxxas TRA3483, Traxxas Sledge 77mm Brushless Motor (2000Kv)
TRA3483, Traxxas Sledge 77mm Brushless Motor (2000Kv) Traxxas 2200kv 77mm Brushless Motor. This is a replacement motor used on the Traxxas Sledge. Features include pre-installed 6.5mm gold plated connectors and a high efficiency heatsink motor can. Package includes one complete motor. Fits: Traxxas Sledge This product was added to our catalog on June 30, 2021
$149.99
-
![TRA3461, Traxxas Velineon 540XL Brushless Motor (2400Kv)]()
Traxxas TRA3461, Traxxas Velineon 540XL Brushless Motor (2400Kv)
TRA3461, Traxxas Velineon 540XL Brushless Motor (2400Kv) This is a replacement Traxxas Velineon 540XL 2400Kv Brushless Motor. This motor is a replacement for the Traxxas Maxx and features 12-gauge wire and gold-plated bullet connectors to make it easy to install. Fits: Traxxas Hoss Traxxas Maxx WideMaxx Traxxas Maxx This product was added to our catalog on April 28, 2021
$119.99
-
![TRA3480, Traxxas Velineon VXL-6S Brushless Power System]()
Traxxas TRA3480, Traxxas Velineon VXL-6S Brushless Power System
TRA3480, Velineon® VXL-6s Brushless Power System, waterproof (includes VXL-6s ESC SKU: TRA3485 and 2200Kv, 75mm motor SKU: TRA3481) Traxxas Velineon VXL-6S Brushless Power System. This replacement power system is intended for the Traxxas E-Revo VXL 2.0 or the Unlimited Desert Racer. Package includes one motor and one ESC.Specifications: ESC: Input Voltage: (2) 2s or 3s LiPos (Max 25.2 volts) Case Size: 2.23in (58mm) x 2.83in (72mm) x 1.81in (46mm) Weight: 206.5g (7.28oz) Motor Connectors: Traxxas 6.5mm Bullet Connectors BEC Voltage: 6.0 V BEC Continuous Current: 10A BEC Peak Current: 20A Power Wire: 10-Gauge Maxx® Cable Motor: kV: 2200 Can Length: 77.5mm Can Diameter: 41.8mm Total Length: 98.5mm Shaft Length: 21mm Shaft Diameter: 4.99mm Replacement part for these models: E-Revo VXL Brushless Unlimited Desert Racer This product was added to our catalog on April 12, 2021
$269.99
-
![HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T)]()
HobbyWing HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T)
HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T) The Hobbywing Quicrun 3650 G2 Sensored Brushless Motor is a high efficiency option, creating good power, and keeping temps low. Ideal for 1/10th, 1/12th On-road (Race or drift Touring cars, F1, M vehicles and etc.) & Off-road (Buggies/2WD SCTs & Trucks) STOCK/SPORT Class Competitions (About Motors' T counts, please refer to rules regulated by race organizers), Beginners for practice, and Rock Crawlers (applicable to 21.5T,25.5T motors) applications. Features: Built-in Hall sensor brings drivers an amazing sense of control. Top-quality components: heat-resistant magnet, heat-resistant wires and name-brand bearings. Dustproof design where motor leads exit. Features a gold-plated lockable connector which can be fastened by screws, eliminating the possibility of losing connections. Detachable structure is easy to clean and maintain, greatly prolonging the service life of the motor. Specifications: Turn: 21.5T Kv: 1800Kv LiPo: 2-3S Shaft Diameter: 3.175mm Resistance: 0.0747 ohm No Load Current: 1.3A Max Output Power: 95W Max Output Current: 28A Weight: 186g This product was added to our catalog on May 3, 2023
$54.99
-
![CSE060-0064-00, Castle Creations 2028 Extreme 1/5 Scale Sensored Brushless Motor (800Kv)]()
Castle Creations CSE060-0064-00, Castle Creations 2028 Extreme 1/5 Scale Sensored Brushless Motor (800Kv)
CSE060-0064-00, Castle Creations 2028 Extreme 1/5 Scale Sensored Brushless Motor (800Kv) The Castle Creations "2028 Extreme" 1/5 Scale Sensored Brushless Motor is the first of its kind - a SENSORED motor, developed for large scale, high voltage applications! The Sensored 2028 features an improved 4-POLE 12-SLOT design that boasts exceptional efficiency and produces less heat than its predecessor. Designed specifically for demanding large scale applications, the Sensored 2028 delivers next level large scale power and will no doubt hold up to the heavy throttle and extended usage that 1/5th scale vehicles like the Losi 5IVE-T, 5IVE-B or DBXL-E encounter. This is the ULTIMATE upgrade for any 1:5 scale vehicle (including gas to electric conversions) weighing up to 30 lbs for 2WD and 25 lbs. for 4WD. Without a robust and reliable design, the massive power and efficiency can only take you so far. RC enthusiasts love pushing their equipment to the edge. Castle engineers know this and spared no expense when developing a design that could hold up to the harsh conditions that the RC community will throw at it. This results in a cooler running motor, and a cooler motor has a longer lifespan. Construction of this motor required careful component selection; each verified through internal testing to ensure the highest efficiency possible. The result is a motor with unmatched quality, performance, and reliability. Features: The 2028 Extreme can easily run in the 10 horsepower range (Burst power output for duration's typical of vehicle acceleration.) Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Proprietary winding techniques allow Castle Creations to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Dual sensor ports to ensure optimal installation in your large-scale vehicle. Updated modern and sleek design that looks as cool as it performs. NOTE: Items Needed for Operation: Compatible Electronic Speed Control (ESC) (see Recommended ESCs below) Product Use Statements: Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the motor or ESC. Application Guidelines: The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the Running & Maintaining document in the resources tab above for info on running and maintaining motors in wet environments. Specifications: Input Voltage Range: 12S MAX Kv: 800 Max. RPM: 45,000 Minimum Input Voltage: 3S Maximum Input Voltage: 12S Sensored Capable: Yes Can Length: 4.4" (113.2mm) Can Diameter: 2.2" (57mm) Weight (w/wires): 44 oz./1.25kg Shaft Size: Length: 30mm Diameter: 8mm Mounting Hole Specifications: 4mm holes @ 30mm spacing. Cooling Fan: Available, but not included. See 011-0019-00 here. Connectors: 8.0mm male connectors Recommended ESC: Mamba XL X Running modes: Sensorless and Sensored Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs. This product was added to our catalog on March 22, 2021
$274.99
-
Spektrum SPMXSM2000, Firma 3660 3200Kv 4-Pole Brushless Motor: 5mm
SPMXSM2000, Firma 3660 3200Kv 4-Pole Brushless Motor: 5mm
$114.99
-
![FAN28500 - FACTS MACHINE v3 – BRUSHLESS ROTOR TESTER]()
Fantom Racing FAN28500 - FACTS MACHINE v3 – BRUSHLESS ROTOR TESTER
Have you ever been at a race and wondered how the top finishers seem to have faster motors than everyone else? One of the reasons for this is because the fast guys know how to tune their motors with different rotors. Most motor companies now offer optional tuning rotors, but without a way to measure their magnetic strength, there is no way for you to know what strength rotor you are putting in your motor and therefore no way to fine-tune your motor correctly. In addition, rotors are not all created equal. Due to tolerances in the manufacturing process, some are better than others and the fast guys have figured this out. Tuning your motor with the correct rotor is the most critical step in getting the maximum performance out of your motor. Do you know that the strength of your rotor has the single biggest effect on how your motor runs, yet most racers don’t even know what strength rotor they have in their motor? This is like not knowing whether you have a 4, 6 or 8 cylinder engine in your real car. This basically leaves you guessing at how to gear your car and where to set the motor timing. Furthermore, without the correct rotor in your motor, your motor may never run up to its full potential for the application that it is being used for. Now, with the new FACTS MACHINE v3 rotor tester, this easy to use tool gives you the ability to accurately test the magnetic field strength of all of your rotors! No more guessing…get the “FACTS” and the edge over your competition with the FACTS MACHINE v3 Brushless Rotor Tester! IMPORTANT: It is important to know that there is no standard in the R/C industry for testing brushless rotors. There are numerous testers on the market, including the Trinity, MMS, and others, that all provide different information. This information can vary greatly. For example, one company’s meter may read 1500 for a rotor, where our meter may read it as 1400. The Fantom Facts Machine v3 is not mass produced, but rather is hand-built one at a time, in the U.S.A., to the highest standards in the R/C industry. Also, the Facts Machine v3 calibration is double-checked for the highest accuracy possible, so you can feel confident that we are providing you with the most precise rotor tester in R/C. FEATURES: Precision Calibrated – Accurately Measures Magnetic Field Strength Of Brushless Rotors Works With Most Brand 540 Size Rotors and All Diameters (maximum length of 1.54 inches / 39mm) Displays The Highest Measurement For Both Poles At The Same Time Until The Unit Is Reset (eliminates having to memorize or having to write down each number) Lighted LCD Display – Reads Out To 4 Numeric Places (example: 1550) AC Powered – Includes 6v Wall Power Supply Laser Engraved Fantom Logo RoHS Compliant – Built With All Lead-Free Components And Solder Comes in a sturdy, foam padded storage box Hand Built In The USA! SPECS: DIMENSIONS: 4.17″ (106mm) L x 1.58″ (40mm) W x 0.72″ (18.4mm) H (1.18″ / 30mm H including standoffs) WEIGHT: 2.23 ounces (63.22 grams) This product was added to our catalog on September 10, 2021
$179.99
-
![FAN28501 - FACTS MACHINE 3S – BRUSHLESS MOTOR RESISTANCE / INDUCTANCE METER]()
Fantom Racing FAN28501 - FACTS MACHINE 3S – BRUSHLESS MOTOR RESISTANCE / INDUCTANCE METER
Introducing our latest motor testing tool, the Facts Machine 3S Precision Resistance / Inductance Meter! This incredible new tool allows you to test both the resistance and inductance of your brushless motor! This information is critical in knowing the performance capability of your motors. Did you know that knowing the inductance of your motor is just as important as knowing the resistance? Yet most racers don’t pay much attention to this. Most racers are only concerned with getting the lowest resistance stator they can find, however, this is only half the equation in finding the best stator possible. Inductance also plays a very important role in your motor’s performance. The general rule of thumb is the combination of the lowest resistance and highest inductance produces the highest performance for R/C motors and the difference between these two numbers we call the “spread”. Typically, the bigger the spread, the better the motor will perform. For example, using common 17.5 turn numbers of 18.0 milliohms as the resistance number and 30.0 milliHenries as the inductance number, this is a spread of 12. If you could find another 17.5, for example, with a spread of 12.5, this motor will run better on the track compared to the motor with the spread of 12. Not knowing the “spread” basically leaves you guessing at what motor is truly best in your box. In addition, the Fantom Facts Machine 3S is not mass produced, but rather is hand-built one at a time, in the U.S.A., to the highest standards in the R/C industry. The Facts Machine 3S calibration is double-checked for the highest accuracy possible, using 5% tolerance resistors and inductors, referenced to our shop Instek GOM-802 milliohm meter and Duoyi inductance meter, so you can feel confident that we are providing you with the most precise stator tester in R/C. To purchase an Instek GOM-802 and quality inductance meter costs over $500, so the Facts Machine 3S is an incredible value for all serious racers. Now, with the new FACTS MACHINE 3S Resistance / Inductance Meter, you can test the two most important factors of your stator with one compact and easy to use tool! No more guessing…get the “FACTS” and the edge over your competition with the FACTS MACHINE 3S Brushless Motor Resistance / Inductance Meter! FEATURES: Precision Calibrated Using an Instek GOM-802 milliohm Meter (same as ROAR uses) and a Duoyi DY-4070G Inductance Meter Resistance Range: 0 to 999 milliohms Inductance Range: 0 to .999 milliHenries Displays both Resistance and Inductance Numbers, of all 3 poles, at the same time until the unit is reset (eliminates having to memorize or having to write down each number) Lighted LCD Display High-quality Mueller® Gold-plated resistance clips and high-quality Kelvin inductance clips Capable of testing each pole individually or two poles at a time AC Powered – Includes 6v Wall Power Supply 3D Printed Case with Fantom Logo Comes in a sturdy, foam padded storage box Hand Built In The USA! SPECS: DIMENSIONS: 2.85″ (72mm) L x 1.58″ (40mm) W x 0.72″ (18.4mm) H (0.78″ / 20mm H including screen) WEIGHT: 2.45 ounces (69.46 grams) This product was added to our catalog on September 10, 2021
$199.99
-
![FAN19233 - ICON V2 PRO DRAG MODIFIED MOTOR – 3.5 TURN]()
Fantom Racing FAN19233 - ICON V2 PRO DRAG MODIFIED MOTOR – 3.5 TURN
(image is representative of the motor design, but not the wind of the motor) In The Box 3.5 Turn ICON v2 Pro Drag Modified Re-Shim Rotor: Teflon Timing Screw Options: Pro Titanium Bearing Options: Axon X10 Hybrid Bearings Rotor Options: 13.0 Rotor Strength Test: Yes Coil Resistance Test: Yes Optional Sensor Board Adjustment Plate: Red Optional Stationary End Plate: Red Designed in the USA, we are proud to announce the ALL NEW ICON V2 PRO MODIFIED SERIES RACING MOTORS for the ULTIMATE RAW POWER, TORQUE, RPM & EFFICIENCY! The heart of the new ICON V2 Pro Mod is our “Patented” (U.S. Patent D823,803) designed stator. Our patented design stator provides maximum torque while producing the most insane RPM ever seen before! That’s correct, another first from Fantom! With our unique design, we’ve totally eliminated the need for stator screws! Up your game and see for yourself why the all-new ICON V2 Pro Modified truly is a Game Changer! Whether you race On-Road or Off-Road, 1S or 2S…..We’ve got you covered!! SPECS AND FEATURES: All R&D Done In The USA Patented Stator Design (U.S. Patent D823,803) New Stator Design for Maximized Torque & Efficiency New Super High Strength and Heat Resistant Magnet Formula New Sensor Board Design for Improved Deviation Accuracy & Reliability Maximum Size Allowed, Pure Copper Wire for Lowest Resistance Possible Precision Machined 1-Piece Can Design High-Inductance / Low Resistance, 3mm Aluminum, Silver Plated Collector Ring Venting & Can Designed to Maximize Heat Dissipation Premium Grade Kawasaki® Steel Stator Plates CNC Machined Billet T6 Aluminum End Plate for Precision Bearing Alignment Maximized Adjustable Timing High RPM Precision Bearings 13.0mm Hi-Torque Ultra Select Rotor Meets All BRCA, IFMAR, EFRA Specifications ROAR Approval Pending Patented Stator Design (U.S. Patent D823,803) THIS MOTOR INCLUDES THE FOLLOWING IN THE BASE PRICE: Professionally built to our strict standards, which includes the rotor properly shimmed (brass shims), complete evaluation of the coils, rotor strength and asymmetry and sensor board deviation. The timing is also set to our recommended setting for your application All modified motors are guaranteed to meet our strict specifications, whether you choose the “Test Options” or not. IF YOU CHOOSE ANY OF THE OPTIONAL UPGRADE PARTS LISTED ABOVE, YOU WILL ALSO RECEIVE THE ORIGINAL STOCK PARTS. THIS INCLUDES THE ROTOR, BEARINGS, STEEL SCREWS, SENSOR BOARD ADJUSTMENT PLATE, AND STATIONARY END PLATE. MOTOR STANDARD AND OPTIONS DETAILS: Re-Shim (standard brass shims) – Included in the price. We adjust the rotor shims so that the rotor “floats” centered properly within the magnetic field. If required, the rotor shaft is also polished to ensure that it fits the inner race of the bearing correctly. We also make sure that it has the correct end play, so that it is not bound up or too loose. Rotor Re-Shim Option (TEFLON® shims) – As with the standard brass re-shim option above, we adjust the rotor shims so that the rotor “floats” centered properly within the magnetic field. With this option, we also use TEFLON® shims for the outermost shims, to minimize any side-load binding between the rotor and bearings. If required, the rotor shaft is also polished to ensure that it fits the inner race of the bearing correctly. We also make sure that it has the correct end play, so that it is not bound up or too loose. Bearing Option – If you choose the AXON X10 hybrid bearings option, we make sure the bearings seats are sized correctly before installing the bearings. This ensures that the bearings are not squeezed or distorted when installed, which could cause extra drag or non-concentrical bearing movement. If required, the rotor shaft is also polished to ensure that it fits the inner race of the bearings correctly. Rotor Options – Choose the 13.0mm modified rotor at no extra cost, or choose the 13.5, 12.5, 12.3mm or 12.0mm optional modified rotor listed above. There is an up-charge for the optional 13.5, 12.5, 12.3mm or 12.0mm modified rotor, but you will also receive the original 13.0mm rotor if you choose the “optional” 13.5, 12.5, 12.3mm or 12.0mm modified rotor. All rotors are checked for correct bearing fit. If required, the rotor shaft is polished to ensure that it fits the inner race of the bearing correctly. Pro Titanium Timing Adjustment Screws Option – Eliminates the power robbing magnetic drag on the rotor that the stock steel screws cause and improves RPM, efficiency and horsepower!Increases RPM by 100+ RPM compared to the stock steel screws!Reduces weight by .26 grams compared to the stock steel screws! Rotor Strength Test Option – Your rotor is tested to make sure it meets proper specs. If we find that the rotor does not meet our strict standards, we will replace it. With this test, the rotor’s magnetic field strength is tested on our Fantom Facts Machine v3 rotor tester. If you choose the printout option, the rotor test results of your rotor are supplied with your motor. If you choose an optional rotor, we will test both of your rotors. All modified rotors are guaranteed to meet our strict specifications, even if you don’t choose the print option. Coil Resistance Test Option – Your stator is tested to make sure it meets proper specs. With this test, we evaluate the ohms resistance of your stator to make sure it meets proper specs and to detect shorts. Each coil is tested individually. If we find that the stator does not meet our strict standards, we will replace it. With this test, the stator coils are tested on an Instek GOM-804, which is the same as ROAR uses. If you choose the printout option, the coil test results of your stator are supplied with your motor. All modified stators are guaranteed to meet our strict specifications, even if you don’t choose the print option. Motor Evaluation Option – All modified motors are evaluated using the highly accurate Motolyser brushless motor tester. This includes checking the rotor asymmetry, as well as the sensor board deviation and timing accuracy. If you choose the printout option, the test results of your motor are supplied with your motor. FEEL THE POWER…FEEL THE FANTOM This product was added to our catalog on September 10, 2021
$168.00
-
![FAN19133F - ICON V3 PRO DRAG MODIFIED MOTOR – 3.0 TURN]()
Fantom Racing FAN19133F - ICON V3 PRO DRAG MODIFIED MOTOR – 3.0 TURN
(image is representative of the motor design, but not the wind of the motor) In The Box 3.0 Turn ICON v2 Pro Drag Modified Re-Shim Rotor: Teflon Timing Screw Options: Pro Titanium Bearing Options: Axon X10 Hybrid Bearings Rotor Options: 13.0 Rotor Strength Test: Yes Coil Resistance Test: Yes Optional Sensor Board Adjustment Plate: Green Optional Stationary End Plate: Green Designed in the USA, we are proud to announce the ALL NEW ICON V2 PRO MODIFIED SERIES RACING MOTORS for the ULTIMATE RAW POWER, TORQUE, RPM & EFFICIENCY! The heart of the new ICON V2 Pro Mod is our “Patented” (U.S. Patent D823,803) designed stator. Our patented design stator provides maximum torque while producing the most insane RPM ever seen before! That’s correct, another first from Fantom! With our unique design, we’ve totally eliminated the need for stator screws! Up your game and see for yourself why the all-new ICON V2 Pro Modified truly is a Game Changer! Whether you race On-Road or Off-Road, 1S or 2S…..We’ve got you covered!! SPECS AND FEATURES: All R&D Done In The USA Patented Stator Design (U.S. Patent D823,803) New Stator Design for Maximized Torque & Efficiency New Super High Strength and Heat Resistant Magnet Formula New Sensor Board Design for Improved Deviation Accuracy & Reliability Maximum Size Allowed, Pure Copper Wire for Lowest Resistance Possible Precision Machined 1-Piece Can Design High-Inductance / Low Resistance, 3mm Aluminum, Silver Plated Collector Ring Venting & Can Designed to Maximize Heat Dissipation Premium Grade Kawasaki® Steel Stator Plates CNC Machined Billet T6 Aluminum End Plate for Precision Bearing Alignment Maximized Adjustable Timing High RPM Precision Bearings 13.0mm Hi-Torque Ultra Select Rotor Meets All BRCA, IFMAR, EFRA Specifications ROAR Approval Pending Patented Stator Design (U.S. Patent D823,803) THIS MOTOR INCLUDES THE FOLLOWING IN THE BASE PRICE: Professionally built to our strict standards, which includes the rotor properly shimmed (brass shims), complete evaluation of the coils, rotor strength and asymmetry and sensor board deviation. The timing is also set to our recommended setting for your application All modified motors are guaranteed to meet our strict specifications, whether you choose the “Test Options” or not. IF YOU CHOOSE ANY OF THE OPTIONAL UPGRADE PARTS LISTED ABOVE, YOU WILL ALSO RECEIVE THE ORIGINAL STOCK PARTS. THIS INCLUDES THE ROTOR, BEARINGS, STEEL SCREWS, SENSOR BOARD ADJUSTMENT PLATE, AND STATIONARY END PLATE. MOTOR STANDARD AND OPTIONS DETAILS: Re-Shim (standard brass shims) – Included in the price. We adjust the rotor shims so that the rotor “floats” centered properly within the magnetic field. If required, the rotor shaft is also polished to ensure that it fits the inner race of the bearing correctly. We also make sure that it has the correct end play, so that it is not bound up or too loose. Rotor Re-Shim Option (TEFLON® shims) – As with the standard brass re-shim option above, we adjust the rotor shims so that the rotor “floats” centered properly within the magnetic field. With this option, we also use TEFLON® shims for the outermost shims, to minimize any side-load binding between the rotor and bearings. If required, the rotor shaft is also polished to ensure that it fits the inner race of the bearing correctly. We also make sure that it has the correct end play, so that it is not bound up or too loose. Bearing Option – If you choose the AXON X10 hybrid bearings option, we make sure the bearings seats are sized correctly before installing the bearings. This ensures that the bearings are not squeezed or distorted when installed, which could cause extra drag or non-concentrical bearing movement. If required, the rotor shaft is also polished to ensure that it fits the inner race of the bearings correctly. Rotor Options – Choose the 13.0mm modified rotor at no extra cost, or choose the 13.5, 12.5, 12.3mm or 12.0mm optional modified rotor listed above. There is an up-charge for the optional 13.5, 12.5, 12.3mm or 12.0mm modified rotor, but you will also receive the original 13.0mm rotor if you choose the “optional” 13.5, 12.5, 12.3mm or 12.0mm modified rotor. All rotors are checked for correct bearing fit. If required, the rotor shaft is polished to ensure that it fits the inner race of the bearing correctly. Pro Titanium Timing Adjustment Screws Option – Eliminates the power robbing magnetic drag on the rotor that the stock steel screws cause and improves RPM, efficiency and horsepower!Increases RPM by 100+ RPM compared to the stock steel screws!Reduces weight by .26 grams compared to the stock steel screws! Rotor Strength Test Option – Your rotor is tested to make sure it meets proper specs. If we find that the rotor does not meet our strict standards, we will replace it. With this test, the rotor’s magnetic field strength is tested on our Fantom Facts Machine v3 rotor tester. If you choose the printout option, the rotor test results of your rotor are supplied with your motor. If you choose an optional rotor, we will test both of your rotors. All modified rotors are guaranteed to meet our strict specifications, even if you don’t choose the print option. Coil Resistance Test Option – Your stator is tested to make sure it meets proper specs. With this test, we evaluate the ohms resistance of your stator to make sure it meets proper specs and to detect shorts. Each coil is tested individually. If we find that the stator does not meet our strict standards, we will replace it. With this test, the stator coils are tested on an Instek GOM-804, which is the same as ROAR uses. If you choose the printout option, the coil test results of your stator are supplied with your motor. All modified stators are guaranteed to meet our strict specifications, even if you don’t choose the print option. Motor Evaluation Option – All modified motors are evaluated using the highly accurate Motolyser brushless motor tester. This includes checking the rotor asymmetry, as well as the sensor board deviation and timing accuracy. If you choose the printout option, the test results of your motor are supplied with your motor. FEEL THE POWER…FEEL THE FANTOM This product was added to our catalog on September 10, 2021
$168.00
-
Trinity TRIPUN1002, Punisher 17.5 Turn Spec Class Sensored Brushless Motor
TRIPUN1002, Punisher 17.5 Turn Spec Class Sensored Brushless Motor Features: Infinite Timing Adjustment True Zero Point Updated Sensor Board Design Open Bearing On Sensor End For Easy Cleaning and Oiling Lower Resistance Solder Tabs Maximized Can Cooling Vents
$99.99
-
![SPMXSM2200, Spektrum RC Firma 550 Sensorless Brushless Motor (1900Kv)]()
Spektrum SPMXSM2200, Spektrum RC Firma 550 Sensorless Brushless Motor (1900Kv)
SPMXSM2200, Spektrum RC Firma 550 Sensorless Brushless Motor (1900Kv) Spektrum Firma 550 Brushless Motor. This motor is a replacement for the Losi Lasernut buggy, but can be used in other 550 motor applications that are compatible with a sensorless motor. This 1900kv motor has a 5mm motor shaft, and includes factory installed bullet connectors. This product was added to our catalog on May 22, 2021
$69.99
-
Trinity TRITEP2022, Slot Machine 17.5T Race Spec Brushless Motor w/TEP1119 Rotor
After months of hard work and testing we are proud to show off the all new Slot Machine. They say that you should never forget where you come from. Here at Team Trinity we always like to take a good trip down memory lane to never forget where we came from. With that said, we are happy to bring back the Slot Machine name with our newest spec motor!The Slot Machine picks up exactly where the X-Factor left off but goes a few steps further. The Slot Machine has a brand new, ground up, stator design that was designed with speed, durability, and efficiency all in mind. Both ends feature CNC machined end plates not only for looks, but functionality as well. With tons of space for heat to escape, you can be confident that your Slot Machine is staying cool in even the hottest of conditions. Having an open stator design not only helps with heat, but also allows for the use of long screws. The long screws go through both end plates as well as the new stator with new, reformulated, epoxy specially designed for strength as well as heat dissipation. Both durability and efficiency all in one! Not only that but, all new 90 degree solder tabs make soldering up your brand new Slot Machine a breeze! Features: New 90 degree solder tabs 2pc CNC Machined Aluminum can allows for more accurate deviation readings X-Flow Cooling which pulls more air through the can, reducing motor temps Infinite timing adjustment capabilities Modular Design with whole-can length hardware and replaceable end caps All new stator design with an immense amount of low end torque without skimping on efficiency
$109.99
-
Trinity TRITEP2023, Slot Machine 21.5T Race Spec Brushless Motor w/TEP1119 Rotor
Slot Machine 21.5T Race Spec Brushless Motor w/TEP1119 Rotor After months of hard work and testing we are proud to show off the all new Slot Machine. They say that you should never forget where you come from. Here at Team Trinity we always like to take a good trip down memory lane to never forget where we came from. With that said, we are happy to bring back the Slot Machine name with our newest spec motor!The Slot Machine picks up exactly where the X-Factor left off but goes a few steps further. The Slot Machine has a brand new, ground up, stator design that was designed with speed, durability, and efficiency all in mind. Both ends feature CNC machined end plates not only for looks, but functionality as well. With tons of space for heat to escape, you can be confident that your Slot Machine is staying cool in even the hottest of conditions. Having an open stator design not only helps with heat, but also allows for the use of long screws. The long screws go through both end plates as well as the new stator with new, reformulated, epoxy specially designed for strength as well as heat dissipation. Both durability and efficiency all in one! Not only that but, all new 90 degree solder tabs make soldering up your brand new Slot Machine a breeze! Features: New 90 degree solder tabs 2pc CNC Machined Aluminum can allows for more accurate deviation readings X-Flow Cooling which pulls more air through the can, reducing motor temps Infinite timing adjustment capabilities Modular Design with whole-can length hardware and replaceable end caps All new stator design with an immense amount of low end torque without skimping on efficiency
$109.99
-
![TEKTT2518, Tekin Pro4 HD 4-Pole Brushless 550 Motor w/5mm Shaft (4,300kV)]()
Tekin TEKTT2518, Tekin Pro4 HD 4-Pole Brushless 550 Motor w/5mm Shaft (4,300kV)
TEKTT2518, Tekin Pro4 HD 4-Pole Brushless 550 Motor w/5mm Shaft (4,300kV) This is the Tekin Pro4 HD 4300kV 4-Pole Brushless Motor. Tekin's Pro4 HD Motor raises the bar in 4wd short course, with the torque and power needed to level the competition. With kV ranges to accommodate 2S, 3S and 4S applications, 1/10 4WD Short Course has never been exposed to this much power! The Pro4 HD's longer 550 can and 4 pole design delivers the off the charts performance gains you need to move your truck to the front of the pack.Features: Designed to be paired with the RX8 Electronic Speed Control 4 Pole 12 Slot Hi-torque 550 Motor Design CNC Machined 6061 T6 Billet Aluminum Heatsink Can Neodymium Sintered Magnets Rebuildable Design High Purity Copper Windings Maximizes Efficiency Precision Engineered for Maximum Energy Conversion Dual-Plug Sensor Wire Harness for use with all sensored systems High RPM ABEC5 Oversized Bearings Specifications:Turns: 1.5DVoltage: 2S - 7.4VkV: 4300Rotor: 18.5mmWeight: 7.8oz / 221gShaft Dimensions: .60x.196" / 15.3x5mmMotor Diameter: 1.4" / 35.8mmMotor Length: 2.5" / 62.5mmBearing Dimensions: Front: 5x14x5mm / Rear: 5x11x5 This product was added to our catalog on December 12, 2021
$245.00$159.99
-
Trinity TRIDM35, Drag Master 3.5T Holeshot Brushless Motor
TRIDM35, Drag Master 3.5T Holeshot Brushless Motor
$199.99$134.39
-
Trinity TRIDM30, Drag Master 3.0T Holeshot Brushless Motor
TRIDM30, Drag Master 3.0T Holeshot Brushless Motor
$199.99$134.39
-
Trinity TRIDM25, Drag Master 2.5T Holeshot Brushless Motor
TRIDM25, Drag Master 2.5T Holeshot Brushless Motor Designed for all out power and speed needed for Extreme - Drag Racing, Pan Cars & Touring CarsStandard Race SPEC Features:Aluminum based sensor board for true sensor alignmentInfinite Timing Adjustment2mm Copper TabsThicker Pure Copper Solder Tabs and CollectorThermal Stator Coating for the best heat dissipation possibleTurbine style vented noseMore Vents for More Cooling220C wire coatingCertified Gauge High Temperature WireShort Stack Stator DesignStator MaterialGrade 5 Ball BearingsUses all D3.5, D4 and 24K Rotors10,000Kv this number is approximate set as Zero Degrees of Timing. Sensored Brushless Motors are not rated in Kv's due to the fact that timing and voltage can effect the Kv number.* MAX Voltage 11.1v 3 Cell Lipo Battery
$199.99$134.39
-
Trinity TRIDM20, Drag Master 2.0T Holeshot Brushless Motor
TRIDM20, Drag Master 2.0T Holeshot Brushless Motor Designed for all out power and speed needed for Extreme - Drag Racing, Pan Cars & Touring CarsStandard Race SPEC Features:Aluminum based sensor board for true sensor alignmentInfinite Timing Adjustment2mm Copper TabsThicker Pure Copper Solder Tabs and CollectorThermal Stator Coating for the best heat dissipation possibleTurbine style vented noseMore Vents for More Cooling220C wire coatingCertified Gauge High Temperature WireShort Stack Stator DesignStator MaterialGrade 5 Ball BearingsUses all D3.5, D4 and 24K Rotors10,000+Kv this number is approximate set as Zero Degrees of Timing. Sensored Brushless Motors are not rated in Kv's due to the fact that timing and voltage can effect the Kv number.* MAX Voltage 11.1v 3 Cell Lipo Battery
$199.99
-
Trinity TRIPUN1001, Punisher 13.5 Turn Spec Class Sensored Brushless Motor
TRIPUN1001, Punisher 13.5 Turn Spec Class Sensored Brushless Motor Features: Infinite Timing Adjustment True Zero Point Updated Sensor Board Design Open Bearing On Sensor End For Easy Cleaning and Oiling Lower Resistance Solder Tabs Maximized Can Cooling Vents
$99.99
-
![CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV)]()
Castle Creations CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV)
CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV) The Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo with 2028 Sensored Motor is a great way to take your build to the next level with Castle’s cutting edge sensored large scale brushless power. The MAMBA MONSTER X 8S COMBO is ready to power any R/C vehicle weighing up to 25lbs, and running all the way up to 8S LiPo. This motor and ESC combo is designed for heavy, high speed rigs, and you'll experience smooth low-end control, without sacrificing power, punch, or speed. The MAMBA MONSTER X 8S utilizes Castle’s breakthrough technology, CRYO-DRIVE. By reducing the rate at which the ESC heats up and removing heat more efficiently, your setup will be able to handle higher gear ratios, in heavier vehicles, with longer runs. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 40mm cooling fan and a forged elliptical fin heatsink, the design maximizes airflow throughout the system, taking thermal performance to a whole new level. The ESC was designed with a robust aluminum casing, and the epoxy potting guarantees protection around the circuitry and ensures all-weather use. Mamba Monster X 8S is a beast, ready to take on the harshest of environments and still perform. You can easily optimize the ESC for any driving condition, from rugged terrain to smooth pavement to the perils of rock and gravel. Create, save and download setup profiles through the Castle Link Programming Suite on your Windows™ PC, or wirelessly with the convenience of the new B-Link™ Bluetooth™ Adapter and Castle Link app for Android or iOS. When paired with the Castle sensored 2028-800KV motor, users with heavy, high power rigs will experience controllable low-end control without sacrificing power, punch or speed. SmartSense™ mode uses the motor’s sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is spinning, it seamlessly transitions to Castle’s ultra-efficient sensorless mode. You’ll put more power to the ground, where it should be, instead of wasting it through raw heat and RPMs. NOTE: This is not a direct replacement to the Mamba XLX. The XLX still handles rawer full throttle power in the most extreme setups. Features: ESC: Input Voltage Range 2S-8S LiPo Sensorless, Sensored and SmartSense™ Running Modes Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V) CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the electronics and promote efficient heat transfer Premium forged heatsink with elliptical fins for superior air flow and increased heat dissipation Oversized factory equipped thermally controlled 40MM cooling fan Compatible with S.BUS2 Telemetry Link and Futaba T4PX and T7PX transmitters Waterproof design for all weather conditions Data logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for "on-the-fly" adjustments using your transmitter Audible alerts for easy diagnosis of common issues such as motor-over-temperature and low-voltage cutoff Convenient transmitter programming for six common adjustable settings including cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store Proudly designed and manufactured in Olathe, KS USA and backed by Castle Creations' 1-year warranty Motor: The 2028 Extreme can easily run in the 10 horsepower range (Burst power output for duration's typical of vehicle acceleration.) Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Proprietary winding techniques allow Castle Creations to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Dual sensor ports to ensure optimal installation in your large-scale vehicle. Updated modern and sleek design that looks as cool as it performs. Specifications: ESC: Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes, waterproof Cooling Fan: Yes, factory equipped (40MM), fully removable** (See Product Use Statements below) Size: L x W x H 69.5mm x 54.1mm x 47mm Weight (with no battery connector): 5.75 oz. (163 grams) Connectors: 6.5mm female bullets for motor connection Motor: Input Voltage Range: 12S MAX Kv: 800 Max. RPM: 45,000 Minimum Input Voltage: 3S Maximum Input Voltage: 12S Sensored Capable: Yes Can Length: 4.4" (113.2mm) Can Diameter: 2.2" (57mm) Weight (w/wires): 44 oz./1.25kg Shaft Size: Length: 30mm Diameter: 8mm Mounting Hole Specifications: 4mm holes @ 30mm spacing. Cooling Fan: Available, but not included. See 011-0019-00 here. Connectors: 8.0mm male connectors Recommended ESC: Mamba XL X Running modes: Sensorless and Sensored Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs. Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately). Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters. Product Use Statements: Recommended battery capacity for 1:6th scale vehicles is 5000mah. Castle recommends using 50C continuous discharge or higher LiPo batteries. Surge ratings should never be used to determine a pack’s suitability for a brushless application. Castle recommends a high current connector designed for high-powered electric systems, rated for 100+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors. Applying voltages higher than 33.6V will cause irreparable damage to ESC. Although Mamba Monster X 8S is waterproof, it is NOT intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt. The cooling fan must be removed prior to driving in wet conditions. *Fan is not waterproof. Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the motor or ESC. The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the Running & Maintaining document in the resources tab above for info on running and maintaining motors in wet environments. Application Guidelines: Mamba Monster X 8S and 2028-800Kv motor is intended for use in 1:6 scale vehicles weighing up to 25 lbs. and up to 8S LiPo. Vehicle Examples: Traxxas™ X-Maxx & Unlimited Desert Racer; Arrma™ Kraton 8s & Limitless; Losi™ Super Rock Rey & Audi R8; Redcat™ Shredder (optional motor mount and modifications may be necessary to install motor). Includes: Mamba Monster X 8S ESC 4-POLE Sensored 2028-800KV Motor Castle Sensor Harness Adapter (installed) 250mm Sensor Wire Mamba Decals Coupon for free Castle Link USB ESC Quick Start Guide Motor Quick Start Guide This product was added to our catalog on April 4, 2021
$459.99
-
![BEL-2041-W, White Scale Outboard with Evinrude W/ Motor]()
OSE BEL-2041-W, White Scale Outboard with Evinrude W/ Motor
BEL-2041-W, White Scale Outboard with Evinrude W/ Motor White Scale Outboard with Evinrude decals.Includes: 1500KV Motor Specs: 6.10 Ounces. Steel gears Prop Shaft: 1/8" (3.17mm) prop shaft Requires: (1) Prop for 1/8" shaft, this unit will fit up to a 40mm diameter propeller. (1) 3s lipo pack. (1) 90 amp ESC (1) Steering linkage hh-817, 4-40 rod, and OSE-83106. Options: 1500kv Outrunner motor Notes: This is designed for scale boats in the 25" (650mm) to 35" (900mm) length range and 3-5 pounds total weight. The manufacturer suggests 1500KV motor with 3s lipo. If your boat falls within those specs, we suggest a Raider 90amp esc, You will be required to solder connectors onto the motor. This product was added to our catalog on March 31, 2023
$1,027.99$285.99
-
![HWA30108000, Hobbywing Quicrun 10BL60 Sensored Brushless ESC]()
HobbyWing HWA30108000, Hobbywing Quicrun 10BL60 Sensored Brushless ESC
Hobbywing Quicrun 10BL60 Sensored Brushless ESC. Features: High performance but low price- users can own this reliable race-ready ESC at an affordable cost. Compact size, suitable for various car chassis. Auto identification system can recognize sensored or sensorless brushless motors automatically. Smooth operation and plentiful adjustment options. Suitable for most kinds of competitions. 8 steps of timing adjustment greatly increase the output power of the motor and unlock its maximum potential. Proportional brake with 4 steps of Maximum Brake Force adjustment, 8 steps of Drag Brake Force adjustment and 4 steps of Initial Brake Force adjustment. 9 steps of acceleration (punch) adjustment, from “soft” to “very aggressive” to fit various of cars, tires and tracks. Multiple protections: Low voltage cut-off protection for LiPo or NiMH battery / Over-heating protection / Throttle signal loss protection / Motor Lock-up protection. One-button sets the ESC. Easily reset all parameters to factory default settings. Compatible with optional device ---- the portable Digital LED Program Card, especially convenient for outdoor use. Specifications: Applications: 1/10 & 1/12 On-road / Off-road / F1 / Drift car race / Street race for fun / Club racing / STOCK race with 0 timing / Drift car race Cont./Peak Current/Resistance: 60A/380A/0.0008? Motor Type Supported: Sensored / Sensorless Brushless Motor Car Applicable: 1:10 On-road/Off-road/Buggy/Monster Motor Limit: 2S LiPo or 4-6 cell NiMH: ?8.5T(1/10 On-road), ?13.5T(1/10 Off-road)* 3S LiPo or 8-9 cell NiMH: ?13.5T(1/10 On-road), ?17.5T(1/10 Off-road)* Battery: 4-9 cell NiMH, 2-3S LiPo BEC Output: 6V/2A (Linear Mode) Size: 33mm(L)*28mm(W)*31.5mm(H, with cooling fan) Weight: 59g (with wires, without cooling Fan) External Program Port: Available *NOTE: Indicates the limit value of motor turns when the ESC timing is set to 0. The larger the timing, the more turns the motor needs. This product was added to our catalog on May 3, 2023
$54.99
-
![SPMXSEMC06, Spektrum RC Firma 160 Amp Sensorless Brushless Smart ESC & Motor Combo (1250Kv)]()
Spektrum SPMXSEMC06, Spektrum RC Firma 160 Amp Sensorless Brushless Smart ESC & Motor Combo (1250Kv)
SPMXSEMC06, Spektrum RC Firma 160 Amp Sensorless Brushless Smart ESC & Motor Combo (1250Kv) Spektrum Firma 160 Amp Sensorless Brushless Smart ESC & Motor Combo, with included 1250Kv motor. Like every component in the Spektrum Smart ecosystem, Firma Smart ESCs combine "plug-and-play" simplicity with the ability to communicate with other Spektrum Smart electronics. Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best. With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity*. Firma ESCs not only gather the data, but also send it to your Smart compatible transmitter in real time, allowing the ability to adjust settings as needed to boost performance on the go. This ESC comes bundled with a Spektrum Firma 1250Kv Brushless Motor capable of handling everything this ESC can put out that is a perfect to get you driving with Spektrum Smart technology. Features: Smart all-in-one telemetry* Fast, powerful 32-bit ARM M4 processor Waterproof Multiple options for easy programming: Button programming Smart ESC Programming Box SmartLink USB Updating and Programmer application Multi-point protection: Over-current protection Automatic LiPo low-voltage cutoff Thermal protection Failsafe protection Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer Comes bundled with Spektrum Firma 1900Kv Brushless Motor Compact for easy installation in most applications Ready to install — no soldering required Rugged plastic case with mounting tabs Aluminum heat sink for high efficiency Cooling fan Firmware updatable through the Smart ESC Programming Box High heat-resistant IC™ connectors, backwards compatible with EC™ connectors Limited 1-year warranty Specifications: Auto Cutoff: Yes BEC: Yes BEC Continous Current: 5A BEC Type: Switch Mode BEC Voltage: 6V Battery Connector: IC5 Battery Input Lead: 10AWG Dual IC5, EC5 compatible Brakes: Yes Bushing Or Bearing: Bearing Cells: 4-8 cell LiPo Connector Type: 6.5mm Bullet Efficiency: 90% Forward: Yes Height: 1.8" (44mm), ESC Input Voltage: 3S - 8S LiPo,12-35.2V Length: 2.7" (70mm), ESC Low-Voltage Cutoff Programmable: Yes Maximum Burst Current: 1050A Maximum Continuous Current: 180A,160A Motor Connector: 6.5mm Bullet Motor Output Lead: 6.5mm Female Bullets Motor Type: Brushless Number of Poles: 4 Outer Diameter: 1.9 in (49mm), motor Output: 6300W Overall Length: 3.3" (85mm), motor Overload Protection: Yes Programmable: Yes RPM/Volt (Kv): 1250Kv Recommended Speed Control: Spektrum Firma 160 Smart ESC Reverse: Yes Sensored: No Shaft Diameter: 3/16" (5mm) Weight: 9.9oz (280g), ESC,26.1oz (740g), motor Width: 3.03" (77mm), ESC Wire Gauge: 10 AWG Includes: (1) Spektrum™ Firma™ Smart ESC (1) Spektrum™ Firma™ 1250Kv Brushless Motor (1) Spektrum Smart sticker sheet (1) Product Manual Needed to Complete: LiPo Battery w/EC5 or Spektrum Smart Battery w/IC5 connector* *NOTE: Smart functionality requires use of Spektrum Smart compatible battery, transmitter and receiver. This product was added to our catalog on March 12, 2021
$219.99
-
![ASC27468, Reedy 680-SL4 Sensorless Brushless Motor (2100kV)]()
Reedy ASC27468, Reedy 680-SL4 Sensorless Brushless Motor (2100kV)
ASC27468, Reedy 680-SL4 Sensorless Brushless Motor (2100kV) Reedy 680-SL4 Sensorless Brushless Motor. This replacement motor is intended for the Team Associated Rival MT8. Package includes one brushless motor. Features: Powerful 4-pole sensorless design Oversized, precision ball bearings High-strength rotor Hardened steel shaft Triple-insulated windings Low-resistance 4.0mm connectors Specifications: Cells: 3-6 LiPo, 8-18 NiMH kV Rating: 2100 Suggested Applications: Monster Truck, 1:8 Buggy & Truggy Dimensions: 68 x 41.2mm Shaft Diameter: 5.0mm Weight: 338g Connectors: 4.0mm bullet This product was added to our catalog on April 29, 2022
$122.99
-
![CSE060-0083-00, Castle Creations 2028 1/6 4-Pole Sensored Brushless Motor (800kV)]()
Castle Creations CSE060-0083-00, Castle Creations 2028 1/6 4-Pole Sensored Brushless Motor (800kV)
CSE060-0083-00, Castle Creations 2028 1/6 4-Pole Sensored Brushless Motor (800kV) This is the Castle Creations 2028 1/6 4-Pole Sensored Brushless Motor now offered in this 1/6 version. Using the same high quality, powerful 2028 design used in 1/5 vehicles this 1/6 version has been tailored to accept the Mamba Monster X 8S ESC with 6.5mm bullet connectors and 10AWG wire. Designed to take on the harsh demands of todays 1/6 vehicles this 2028 motor from Castle Creations offers extreme power and efficiency. This 800KV motor now has an improved 4-Pole 12-Slot design that boasts exceptional efficiency and produces less heat. If you need large scale power this 2028-800KV brushless sensored motor will no doubt hold up to the heavy throttle and extended usage that 1/6th scale vehicles encounter. Features: Running modes include Sensored and an ULTRA-EFFICIENT Sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Our proprietary winding techniques allow us to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Dual sensor ports to ensure optimal installation in your large-scale vehicle. Updated modern and sleek design; looks as cool as it performs. Specifications: Input Voltage Range: 8S LiPo Kv: 800 Max. RPM: 45,000 Sensored Capable: Yes Length: 4.4" (112.7mm) Diameter: 2.2" (56.3mm) Weight (w/wires): 44 oz. (1.25kg) Shaft Length: 30mm Shaft Diameter: 8mm Mounting Hole Specifications: 4mm holes @ 30mm spacing. Cooling Fan: Available, but not included. Recommended CSE011-0153-00 Connectors: 6.5mm male connectors Recommended ESC: Mamba Monster X 8S Running Modes: Sensorless and Sensored Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs.Includes: (1) 2028 1/6 4-Pole Sensored Brushless Motor (800kV) (1) Sensor Cable (3) 6.5mm Female Bullet Connectors Mounting Hardware This product was added to our catalog on November 16, 2022
$274.99
-
![FTK-FUR-2102, Furitek SCX24 Stinger Brushless Power System w/1212-3450kV Brushless Motor]()
Furitek FTK-FUR-2102, Furitek SCX24 Stinger Brushless Power System w/1212-3450kV Brushless Motor
FTK-FUR-2102, Furitek SCX24 Stinger Brushless Power System w/1212-3450kV Brushless Motor The Furitek SCX24 Stinger Brushless Power System with 1212-3450kV Brushless Motor is a great way to get a light weight, high torque power system. This incredible combo includes the Furitek Micro Komodo Motor (FTK-FUR-2100). Don't let the size of this motor fool you, this 12-pole motor was specifically designed to provide high torque at low RPM. The included Lizard Pro ESC allows you to get the most out of this small but mighty motor.Features: Designed specifically for the Axial SCX24 Includes the Furitek Micro Komodo Motor FTK-FUR-2100 12-pole motor design allows for high torque at low RPM Includes Micro Komodo Motor Mount Includes the Furitek Lizard Pro ESC Includes: (1) Lizard Pro 30A/50A Brushed/Brushless ESC (1) Bluetooth module (1) Micro Komodo 1212-3450KV brushless motor (1) 11T 0.3M CNC Brass Pinion (1) CNC aluminum motor mount This product was added to our catalog on April 14, 2022
$129.99
-
![SPMXSM2800, Spektrum RC Firma 6500Kv Brushless Motor]()
Spektrum SPMXSM2800, Spektrum RC Firma 6500Kv Brushless Motor
SPMXSM2800, Spektrum RC Firma 6500Kv Brushless Motor This product was added to our catalog on March 2, 2023
$41.99
-
![HWA30401133, Hobbywing Xerun V10 G3R Competition Stock Spec Brushless Motor (25.5T)]()
HobbyWing HWA30401133, Hobbywing Xerun V10 G3R Competition Stock Spec Brushless Motor (25.5T)
HWA30401133, Hobbywing Xerun V10 G3R Competition Stock Spec Brushless Motor (25.5T) The Hobbywing XeRun V10 G3R Competition Stock Spec Brushless Motor was developed in cooperation with Hobbywing's international team of drivers and features hundred of improvements and adjustments. Developed for competition, this motor has already proven itself at races around the world and is a great weapon for spec class racing. Features: Improved Power & RPM: The optimized stator structure, combined with the super magnetic rotor improves the G3R Stock motor's torque by 13.3%, Kv by 6.5%, and maximum power output by 8.6% compared to the previous V10 G3 Stock motor. Low Resistance - High Efficiency: Resistance is reduced by 11%, and efficiency is improved by 6% when compared to the V10 G3. This improved efficiency helps to significantly slow down the temperature increase. Super Lightweight: The G3R is 8.6% lighter than most popular stock motors. This allows drivers to easily control the balance of their chassis. Great Heat Dissipation: The unique shell design exposes the stator core (laminations) to more air, and when combined with the holes in the front and rear end plates, helps to maximize cooling for outstanding heat dissipation. Rebuildable: The detachable structure makes regular cleaning and maintenance easy, effectively prolonging the service life of the motor and retaining efficiency. Stock & Optional Rotors: The stock super magnetic rotor (HWA30820411) is used in the 13.5 - 21.5 G3R stock motors, and is optimized for Blinky class racing. The optional rotor (HWA30820416) is optimized for Super Stock class racing where boost and turbo timing can be utilized. This motor can be optimized for either class, by simply swapping the rotor. High Quality Components: The use of high performance laminations, heat resistant pure copper wire (200°C), heat resistant rotor (180°C) with strong structure, as well as world class high precision, high strength bearings, and copper solder tabs with super current endurance help to guarantee excellent performance and durability. Specifications: Scale: 1/10th Sensored: Yes Pole Count: 2 Kv Rating: 1780kv LiPo Cells: 2-3S No Load Current: 2.1A Dimensions: 35.9x50.5mm Shaft Diameter: 3.17mm Weight: 145 grams Application: 1/10 stock class racing This product was added to our catalog on May 3, 2023
$104.99
-
![HWA38020336, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (21.5T)]()
HobbyWing HWA38020336, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (21.5T)
HWA38020336, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (21.5T) This is the Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo. Using the precise control of the XR10 Pro G2S combined with a powerful V10 G4 motor gives the user a dominant combo! XR10 Pro G2S 160A ESC: The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC offers all the tuning options needed for competitive racing while giving reliable performance on the track. Helping to keep this ESC reliable is the Frameless Fan Design (FFD) fan system. A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. At the racetrack ESC adjustments can be crucial. The XR10 Pro G2S is packed with features such as several PWM adjustments. From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition. V10 G4 Motor: The V10 G4 Competition Stock Brushless Motor has been greatly optimized to provide maximum torque and increased power. With a lower internal resistance, this motor is more efficient and runs cooler when compared to the G3R motors. To further increase performance the motor adopts a fully exposed stator core allowing more airflow over the stator. The motor also features a high-precision endbell plate to improve consistency and structural stability. Dual sensor ports can be found allowing for different wiring setups. NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended. Features: ESC: Upgraded 32-bit M4 microprocessor with more powerful processing capability guarantees stable control and rapid response. (Industry's highest 32-bit microprocessor, increased processing speed by X4) Peak current up to 1200A. (This is not a typo) Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages. Variable frequency regulation of PWM & amp; brake frequencies allows users to precisely regulate the driving; braking forces (of the motors). Expanded range of the max. brake force brings in the active brake ranges from 101% to 150%. Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency. 10 select-to-use profiles applicable to all 1/10th RC car racing. Internal electronic key switch for long service life, high reliability; and the external switch port for connecting an external switch (included in the product box) is applicable to different situations. Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or WiFi module to the ESC. With the Updated WIFI express module (purchase separately), users are able to program parameters, upgrade firmware and check relevant data during the event using either the iPhone or Android devices. Switchable motor direction (CCW/CW) for various chassis. Multiple protections comes in standard Low-voltage cutoff protection ESC and motor thermal protection Fail safe (throttle signal loss protection) Reverse polarity protection Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real time. Firmware upgrade via Hobbywing multi-function LCD program box or WiFi Express (item sold separately). Motor: Specially designed for high-level racing. Lightweight: The G4 Modified & Stock motors only weigh 161g & 132g respectively. The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor. The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G4 Stock motors (10.5T~25.5T), the timing is adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees. The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts. The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors effectively keep sand or dirt from getting inside and damaging the motor(s). The use of high-performance stator core, heat (200°C) resistant wire, heat (200°C) resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current endurance guarantees outstanding performance and super durability. Specifications: ESC: Cont./Peak Current: 160A / Burst: 1200A Battery: 5-6 cells NiMH/NiCd / 2S LiPo BEC Output: 5V-7.4V Motor Supported: Sensored and sensorless brushless motors Suitable Motor: 3650 Motors 1/10th Touring Car: 4.5T, 1/10th Buggy: 5.5T Application: Brushless motor system for 1/10th, 1/12th Touring Cars & Buggies Racing, Splash proof Wires: Standard 13AWG 200mm Size: 37.5X30.9X32.5mm Weight: 90g (with wires) Motor: kV Rating: 2500kV Cell Count: 2-3S No-Load Current: 3.0A Outer Diameter: 35.8mm Length: 51.4mm Shaft Diameter: 3.175 Weight: 148g Front Bearing: 9x4x4mm Rear Bearing: 8x3x4mm Adjustable Timing: 30-60° Applications: 1/10th Stock Class Racing This product was added to our catalog on May 3, 2023
$319.99
-
![HWI30402550, Hobbywing EZRUN 5687SL 4-Pole 1/5 Scale Sensorless Brushless Motor (1100kV)]()
HobbyWing HWI30402550, Hobbywing EZRUN 5687SL 4-Pole 1/5 Scale Sensorless Brushless Motor (1100kV)
HWI30402550, Hobbywing EZRUN 5687SL 4-Pole 1/5 Scale Sensorless Brushless Motor (1100kV) Hobbywing EZRUN 5687SL 4-Pole 1/5 Scale Sensorless Brushless Motor. Specifications: Model: 5687SL-1100KV Pole: 4 KV (No-load): 1100KV Resistance: 0.0041 Ω Current (No-load): 4.1 A Max Output Power: 5800 W Current at the point of M.O.P: 200 A Motor Diameter: 56mm Motor Length: 87mm Shaft Diameter: 8.0mm Shaft Length: 31.0mm LiPo Cells: 3-8 Weight: 916g (32.21oz) Applicable: 1/5th RC Vehicles Truck/Dragster Suitable ESC: Ezrun MAX5 or MAX6 ESC This product was added to our catalog on April 25, 2019
$169.99
-
![HWI38010802, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/5687SL (1100kV)]()
HobbyWing HWI38010802, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/5687SL (1100kV)
HWI38010802, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/5687SL (1100kV) The Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo includes the 5687SL 1/5 scale, 1150kV motor and is a great option for high-end, aggressively powered, large scale 8S builds. Specifications: Motor: Model: 5687SL-1100KV Pole: 4 KV (No-load): 1100KV Resistance: 0.0041 Ω Current (No-load): 4.1 A Max Output Power: 5800 W Current at the point of M.O.P: 200 A Motor Diameter: 56mm Motor Length: 87mm Shaft Diameter: 8.0mm Shaft Length: 31.0mm LiPo Cells: 3-8 Weight: 916g (32.21oz) Applicable: 1/5th RC Vehicles Truck/Dragster ESC: Continuous Current: 160A Peak Current: Peak Current: Peak Current: 1,050A Motor Type: Sensorless Brushless Motor Applications: 1/6th Touring Car, Buggy, Truggy and Truck Motor Limit: With 6S LiPo/18S NiMH: KV ≤1500 (5892 size motor); With 8S LiPo/24S NiMH: KV ≤1200 (5892 size motor) LiPo/NiMH Cells: 9-24S NiMH, 3-8S LiPo BEC Output: 6V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC) Cooling Fan: Powered by the stable BEC voltage of 6V/7.2V Connectors: Input End: None, Output End: Female 6.5mm Gold Connectors (pre-soldered onto the PCB of the speed controller) Size (LxWxH): 70x56x46.5mm Weight: 240g Programming Port: FAN /PRG Port This product was added to our catalog on April 25, 2021
$289.99
-
![CSE010-0165-00, Castle Creations Mamba Monster X 8S 1/6 Brushless ESC]()
Castle Creations CSE010-0165-00, Castle Creations Mamba Monster X 8S 1/6 Brushless ESC
CSE010-0165-00, Castle Creations Mamba Monster X 8S 1/6 Brushless ESC The Castle Creations Mamba Monster X 8S 1/6 Brushless ESC features CRYO-DRIVE™ - Castle’s latest break-through technology. CRYO-DRIVE minimizes the amount of time the ESC’s electrical components spend generating heat. This proprietary software advancement works in parallel with a unique open housing design and a forged elliptical fin heatsink to allow increased directional airflow to cool critical components. Combine this with a high speed 40mm fan and you have a design that maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling. Mamba Monster X 8S is designed for 1/6 scale vehicles weighing up to 25 lbs. with up to 8S LiPo. Compatible models include the Traxxas™ X-Maxx & Unlimited Desert Racer; Arrma™ Kraton 8s & Limitless; Losi™ Super Rock Rey & Audi R8; Redcat™ Shredder. Features: Input voltage range 2S-8S LiPo Sensored, Sensorless and SmartSense™ running modes Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V) Premium forged heatsink with elliptical fins for superior airflow and increased heat dissipation Oversized factory equipped thermally controlled 40mm fan ? Waterproof design for all weather conditions ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the components and promote efficient heat transfer Data-logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for “on the-fly” adjustments using your transmitter Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1 year warranty Product Use Statements: Recommended battery capacity for 1:6 scale vehicles is 5000mah. Castle recommends using 50C continuous discharge or higher LiPo batteries. Surge ratings should never be used to determine a pack’s suitability for a brushless application. Castle recommends a high current connector designed for high-powered electric systems, rated for 100+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors. Applying voltages higher than 33.6V will cause irreparable damage to ESC. Although Mamba Monster X 8S is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt. The cooling fan must be removed prior to driving in wet conditions. It is not waterproof. Specifications: Application guidelines: 1:6 scale RC hobby vehicles weighing up to 25 lbs Running Modes: Sensored, Sensorless and SmartSense™ (when paired with a Castle 4-POLE 12SLOT sensored motor) Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. Or 8.0V (8A Peak), default 5.5V Operating environment: Waterproof design enables use in nearly any environment Brake: Proportional Reversible: Yes, but may be disabled for racing On /off switch: Yes, waterproof Cooling fan: Yes, factory equipped (40mm), fully removable (See Product Use Statements for more info) Size: L x W x H 69.5mm x 54.1mm x 47mm Weight (w/wires): 5.75 oz. (163 grams) Connector type: 6.5mm female bullets for motor connection Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately). Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters. This product was added to our catalog on May 14, 2021
$214.99
-
![CSE060-0089-00, Castle Creations 1412 Sensored 4-Pole Brushless No Prep Drag Motor (6400kV)]()
Castle Creations CSE060-0089-00, Castle Creations 1412 Sensored 4-Pole Brushless No Prep Drag Motor (6400kV)
Optimized for No Prep RC 2S Drag Racing - High Torque Castle Technology CSE060-0089-00, Castle Creations 1412 Sensored 4-Pole Brushless No Prep Drag Motor (6400kV) The Castle Creations 1412-6400kV Sensored 4-Pole Brushless Motor is a mid RPM design developed specifically for 2S No Prep RC drag racing. 12awg wire and 6.5mm bullet connectors have been combined with an application specific design that allow this motor to create big torque and high watt output. During the design phase, Castle went with a slightly different approach than current motors on the market. Most no prep motors are standard 540 size with very high kv (low turn). These motors rely on high RPM and low torque to push the car down the track (think turbo charged 4 cylinder). The 1412 is longer than most drag motors, which provides significantly more torque, acceleration, and cooler temps (think American Muscle). This results in a high horsepower, snappy, cool running motor. Your final drive ratio will need to be decreased (larger pinion/smaller spur) to get the RPMs up for top speed; due to the size of the motor it will take just about any gearing and CHEAT timing you can throw at it. Castle beefed up the design over a standard 14xx series motor to handle the high demands of drag racing. It uses a 5mm output shaft, 12AWG battery wires and 6.5mm bullets. Due to the high power nature of this motor it is highly recommended to use a 1/8th scale size ESC or larger. The 1/8th Mamba Monster X and 1/6th scale Mamba Monster X 8s are great pairings with this motor. SmartSense SMARTSENSE uses the motors sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is turning, it seamlessly transitions to Castle’s ULTRA- EFFICIENT sensorless mode. When running, a motor must transition between different load points and a different timing advance is required for optimal efficiency at all load points. Using mechanical timing adjustments alone, you can only target one driving condition, such as higher start power or higher top end speed. This sacrifices performance and efficiency during the other driving phases. Electronic timing in SMARTSENSE will advance timing automatically for peak performance during all driving conditions. This allows users to combine the best of both worlds in an unrivaled HYBRID between smooth sensored startups and high-efficiency sensorless drive. Features: 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 12 AWG high strand wire with 6.5mm male Castle bullet connectors Kevlar wrapped rotor High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: Input Voltage Range: 2S LiPo Kv: 6400 Max. RPM: 75,000 Length: 62.5mm Diameter: 36mm Weight (w/wires): 283g (9.98oz) Shaft Length: 21mm Shaft Diameter: 0.197" (5mm) Mounting Hole Specifications: M3 @ 25mm Cooling Fan: Optional - not included Connectors: 6.5mm male Castle Bullet Connectors Application Guidelines: For 2WD Street Eliminator on 2s Recommended ESC(s): Mamba Monster X, Mamba Monster X 8s This product was added to our catalog on December 31, 2021
$139.99
-
![HWI30402950, Hobbywing EZRUN 4985SL 4-Pole 1/6-1/7 Scale Sensorless Brushless Motor (1650kV)]()
HobbyWing HWI30402950, Hobbywing EZRUN 4985SL 4-Pole 1/6-1/7 Scale Sensorless Brushless Motor (1650kV)
HWI30402950, Hobbywing EZRUN 4985SL 4-Pole 1/6-1/7 Scale Sensorless Brushless Motor (1650kV) Hobbywing EZRUN 4985SL 4-Pole 1/6-1/7 Scale Sensorless Brushless Motor. Specifications: Model: 4985SL-1650KV Pole: 4 KV (No-load): 1650KV Resistance: 0.0053 ? Current (No-load): 5.4 A Max. Output Power: 5700 W Current at the point of M.O.P: 160 A Motor Diamter: 49mm Motor Length: 86.5mm Shaft Diameter: 5.0mm Shaft Length: 21.5mm LiPo Cells: 3-6 Weight: 587g (20.71oz) Applications: 1/6th & 1/7th RC Vehicles Suitable ESC: Ezrun MAX6 ESC This product was added to our catalog on April 25, 2021
$149.99
-
![SPMXSEMC05, Spektrum RC Firma 150 Amp Sensorless Brushless Smart ESC & Motor Combo (2050Kv)]()
Spektrum SPMXSEMC05, Spektrum RC Firma 150 Amp Sensorless Brushless Smart ESC & Motor Combo (2050Kv)
SPMXSEMC05, Spektrum RC Firma 150 Amp Sensorless Brushless Smart ESC & Motor Combo (2050Kv) Spektrum Firma 150 Amp Sensorless Brushless Smart ESC & Motor Combo, with included 2050Kv motor. Like every component in the Spektrum Smart ecosystem, Firma Smart ESCs combine "plug-and-play" simplicity with the ability to communicate with other Spektrum Smart electronics. Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best. With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity*. Firma ESCs not only gather the data, but also send it to your Smart compatible transmitter in real time, allowing the ability to adjust settings as needed to boost performance on the go. This ESC comes bundled with a Spektrum Firma 2050Kv Brushless Motor capable of handling everything this ESC can put out that is a perfect to get you driving with Spektrum Smart technology. *NOTE: Smart functionality requires use of Spektrum Smart compatible battery, transmitter and receiver. Features: Smart all-in-one telemetry* Fast, powerful 32-bit ARM M4 processor Waterproof Multiple options for easy programming: Button programming Smart ESC Programming Box SmartLink USB Updating and Programmer application Multi-point protection: Over-current protection Automatic LiPo low-voltage cutoff Thermal protection Failsafe protection Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer Comes bundled with Spektrum Firma 2050Kv Brushless Motor Compact for easy installation in most applications Ready to install — no soldering required Rugged plastic case with mounting tabs Aluminum heat sink for high efficiency Cooling fan Adjustable high-power BEC Firmware updatable through the Smart ESC Programming Box High heat-resistant IC™ connectors, backwards compatible with EC™ connectors Limited 1-year warranty Specifications: Auto Cutoff: Yes BEC: Yes BEC Continous Current: 5A BEC Type: Linear BEC Voltage: 6V Battery Connector: IC5 Battery Input Lead: IC5, EC5 compatible Brakes: Yes Forward: Yes Height: 1.5" (38.5mm), ESC Input Voltage: 3S - 6LiPo Length: 2.3" (58mm), ESC Low-Voltage Cutoff Programmable: Yes Maximum Burst Current: 950A Maximum Continuous Current: 150A Motor Connector: 4mm Bullet Motor Output Lead: 5.9" (150mm) 10AWG Output: 3000W Overload Protection: Yes Programmable: Yes RPM/Volt (Kv): 2050Kv Reverse: Yes Sensored: No Weight: 8.4oz (238g), ESC Width: 1.9" (47.5mm) without tabs, 2.3" (59.5mm) with tabs, ESC Includes: (1) Spektrum™ Firma™ Smart ESC (1) Spektrum™ Firma™ 2050Kv Brushless Motor (1) Spektrum Smart sticker sheet (1) Product Manual Needed to Complete: LiPo Battery w/EC5 or Spektrum Smart Battery w/IC5 connector* *NOTE: Smart functionality requires use of Spektrum Smart compatible battery, transmitter and receiver. This product was added to our catalog on March 12, 2021
$219.99
You have seen 48 out of 66 products