PTK-1570, ProTek RC CA Tire Glue w/Glue Tip (Medium) (0.75oz)
This is a 0.75 ounce bottle of ProTek R/C CA Tire Glue in Medium thickness. ProTek R/C CA Glue is a high performance clear cyanoacrylate with a medium viscosity that ensures gap penetration with a relatively quick 5-10 minute dry time.
ProTek R/C CA Tire Glue is ideal for mounting rubber tires onto R/C car plastic wheels, but is ideal for a wide variety of applications and will bond nearly anything; ProTek R/C CA Tire Glue is not foam safe however.
Features:
Medium viscosity
5-10 minute dry time
Ideal for gluing R/C tires
Bonds nearly any material
Compact, pocket sized bottle
One glue tip included (also available separately: PTK-1571)
NOTE:
This glue is not foam safe.
Store in cold dry environment
This product was added to our catalog on December 16, 2021
PTK-LIPOSAFE, ProTek RC Flame Resistant LiPo Charging Bag (Large, 23x30cm)
This is a ProTek R/C Flame Resistant Lithium Polymer Charging Bag, and is intended to reduce the chance of damage or injury in the event of a LiPo fire.
The ProTek LiPo Safe Charging Bag is rated up to 30 watt-hours and is made of high tech space-age materials that will help to contain a lithium polymer battery fire. Place your lithium polymer battery inside the LiPo Safe Charging Bag and extend the charging wires through the top flap. Charge your LiPo batteries in the LiPo Safe Charging Bag for peace of mind and a higher level of safety. In the event of a lithium polymer battery mishap, the LiPo Safe Charging Bag’s fire-resistant material reduces the severity of the fire inside and vents the smoke outside the LiPo Safe Bag. The Charging Bag is sealed with a thick, industrial strength Velcro flap and can also be used for safe transportation and storage of your Lithium Polymer batteries.
Due to the volatile nature of Lithium chemistry batteries, charging bags such as the ProTek Lithium Polymer Flame Resistant Storage Bag are required by many tracks, flight clubs and at ROAR sanctioned events.
WARNING:
Never leave charging battery unattended
Always ensure the battery is on a non-flammable surface
Ensure flap is sealed while charging
This ProTek R/C lithium charging bag is intended to reduce the chance of damage in the event of a LiPo fire
Not recommended for batteries exceeding 30 watt-hours
Instructions:
Ensure that charger rate is properly set and polarity is correct
Attach charging leads to battery
Place battery toward the bottom of the LiPo Safe Bag
Place the LiPo Safe Bag on a non-flammable surface
Route charge leads through either vent at the sides of the flap top seam of the LiPo Safe Bag
Close top flap of the LiPo Safe Bag and press hook and loop closure fully closed
Charge battery using proper charging practices
Dimensions: 230x300mm (9x11.8 inches)
This product was added to our catalog on December 16, 2021
PTK-1572, ProTek RC Blue Thread Lock (Medium) (0.34oz)
ProTek R/C Blue Thread Locker is a medium thickness, medium strength formula that provides great resistance towards shocks and vibrations, yet still allows hardware to be removed and disassembled with hand tools. It is a must-have item for 1/8 scale use, 1/10 scale use and especially any vehicle or aircraft with a nitro engine. ProTek R/C Blue Thread Lock also helps to prevent rusting of threads.
For use, simply apply the fluid to the threads of your non-plastic fastener or nut, and tighten. In the absence of air, the fluid will start to cure in about 10 minutes, with a finished full cure in about 24 hours.
Specifications:
Size: 0.34 fl oz. (10ml)
Strength: Blue - Medium
Removable: Yes
Permanent Lock: No
Cure Time: Sets in 10 minutes; full cure in 24 hours
Use: Any non-plastic screw, fastener, nut or bolt
This product was added to our catalog on December 16, 2021
PTK-5129-19, ProTek RC 2S 100C Si-Graphene + HV LiPo Stick Pack TCS Battery (7.6V/5000mAh)
The ProTek R/C 2S 100C Si-Graphene + HV LiPo Stick Pack Battery is built using a hard plastic case that is the same dimensions as a standard NiMH stick pack. This makes them a great choice for Tamiya TCS Series racing, including Euro Truck, all GT classes, M-Chassis and Formula One - as well as Euro Truck Racing League. Plus, its a great choice for any chassis that will accept a 6 cell NiMH stick pack. Weighing in at 235 grams, this Si-Graphene + HV battery weighs less than a standard 5000mAh LiPo battery of the same configuration - making your car lighter and faster!
When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, increased run time, increased cycle life and increased voltage - but Graphene + 100C LiPo batteries take that a step further with more power and lower internal resistance when compared to the previous ProTek LiHV Graphene packs! This provides more runtime, and a dramatic increase in voltage and punch over the course of a run.
Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries, Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 100C discharge ratings, incredibly high charge rates and huge variety of models to choose from, ProTek R/C 100C Graphene + packs are perfect for racers and bashers that demand the absolute best.
Features:
Perfect for Tamiya TCS Series racing
Hard case is the same dimensions as a standard NiMH stick pack
Lighter than a hardcase 2S LiPo pack of equal capacity
Improved power to weight ratio and a lower overall CG
More runtime, with a dramatic increase in voltage and punch
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Increased run time, increased cycle life and increased voltage!
More capacity gram for gram when compared to standard LiPo cells
Perfect for stock class racers looking to shave grams
10C max charge rates - 1C charge rate recommended for longest life
7.6V nominal voltage
Factory installed T-style plug
NOTE: While these batteries are LiHV cells, they can still be charged the same as a standard LiPo with a standard LiPo charger. The overall voltage and capacity will be slightly less than when charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the flat discharge curve, reduced weight and low internal resistance. When charged to 8.4V, these packs will still offer a noticeable advantage when compared to a standard 7.4V LiPo pack.
Battery Model
2S HV LiPo
ROAR Approved
Yes
Type
Silicon Graphene
Voltage
7.6V nominal
Capacity @7.4V
5000mAh
Capacity @7.6V
5400mAh
Weight
235 g
Connector Type
T-style
Balance Connector
3 Pin XH
Number of Cells
2 Cell
Configuration
2S1P
Dimensions (WxLxH)
46.7x137.5x24.2mm
Maximum Charge Rate
10C (50A)
Burst Current
100C
Watt Hour @7.6V
38Wh
Includes:
(1) ProTek R/C Battery
LITHIUM POLYMER SAFETY INFORMATION
IMPORTANT:
DO NOT leave the battery in your model when charging
DO NOT leave unattended when charging
ALWAYS balance charge the battery
ALWAYS use a LiPo charging bag
YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)
YOU MUST not over discharge the Li-Poly battery pack
READ & UNDERSTAND the instructions carefully before operating this battery
NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage. Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on April 16, 2021
PTK-2240, ProTek RC Clear Double Sided Servo Tape Roll (1x40")
ProTek R/C Clear Double Sided Tape is a 40" long roll of the 1" wide clear double side tape that has become a must have for RC use. This tape is 1mil thick and is perfect for securing receivers, ESC's or transponders to your RC car. The adhesive on the tape will keep your device securely fastened where you want it, yet the material remains easy to remove and leaves no residue behind. The waterproof, heat resistant properties help it stand up to the elements, and the soft, flexible material will conform to curved or uneven surfaces, and helps to reduce vibration to the component. Protek RC offers two types of double sided tape, clear and grey.
Features:
Perfect for cars, trucks, boats, helicopters, drones, rock crawlers and more!
Strong adhesion and durability
Water proof and heat resistant
Reduces vibration
Soft and flexible
Suitable for curved surfaces
Strong tensile strength
This product was added to our catalog on December 16, 2021
PTK-5626, ProTek RC Heavy Duty EC5 Charge Lead (Male EC5 to 4mm Banana Plugs)
This is a ProTek R/C EC5 Device Charge Lead. This charge lead features two 4mm bullets fixed to 14awg wire.
This product was added to our catalog on December 16, 2021
PTK-5211, ProTek RC Heavy Duty 15cm Universal Servo Y Extension Lead (1 Male/2 Female)
This is one 15cm (6") universal servo Y extension lead from ProTek R/C. These are excellent servo extension leads made with thick, high quality 22awg wire for maximum current carrying capacity and strength.
The male plug installed on these extension leads are JR style connectors and will work with any radio system. The two female ends are designed to accept Futaba connectors, as well as JR, Aitronics and HiTec connectors. When plugging JR style connectors into the female connector, be sure to check for the correct polarity.
This product was added to our catalog on December 16, 2021
PTK-8151, ProTek RC Pit Mat w/Closeable Mesh Bag (120x60cm)
This is the ProTek R/C Pit Mat. The ProTek R/C pit mat will take your work space from suitable, to stunning. With a 24 x 48 footprint and nearly 8 square feet of coverage, this mat is the perfect size for your work space. Made from durable 4mm thick foam material, this mat is easy to clean, roll up and store away. Plus, unlike other pit mats, the ProTek R/C Pit Mat includes a closeable mesh carry bag that makes it easy to throw the mat over your shoulder and haul around. Ditch the dirty towels and silly rubber mats, and start wrenching like a boss with this high quality mat from ProTek R/C.
Features:
Approximately 24 x 48 in. (60 x 120 cm)
Textured surface helps to prevent parts rolling onto the floor
4mm thick padded material provides clean, flat, anti-fatigue surface
Closeable, mesh bag makes for easy storage and transportation
Eye-catching ProTek R/C Styling
This product was added to our catalog on December 2, 2021
PAAPT104, Pacer Technology Zap Model Cement (1oz)
This is a 1 fl. oz tube of Zap Plastic Model Cement from Pacer Technologies. Bonds Polystyrene Plastic Models. Bonds quickly, and forms a water resistant joint once hardened. Dries clear.
Works best on:
Aluminum
China
Cloth
Fiberglass
Metal
Most Plastics
Pottery
Rubber
Wood
This product was added to our catalog on June 6, 2023
PTK-5042, ProTek RC Sheathed T-Style Plug (2 Male)
These ProTek R/C Sheathed T-Style Connectors are compatible with any standard generic T-Style plug, as well as Deans Ultra Plugs. These connectors feature a plastic protective sheath that snap onto the back of the connector concealing the solder joint.
Typical t-style plugs use shrink tubing which works fine, but provides a one-time solution. Using the sheath, you can snap it on or off to make any connector changes or modification, as well as create a sleek and professional look.
Package includes two male plugs and two protective sheaths.
Features:
T-Style connectors
60A max current
Sheathed backing
Concealed solder joint
Labeled polarity
Professional looks
Specifications:
Rated Current： 36A
Max Current: 60A
Internal Resistance: 0.4mΩ
Net Weight (pair): 5.6g
Recommended Wire: 12AWG
Pulling Force: 25N
Recommended Use: 1000 times
Rated Temperature： -20°C - 120°C (-4°F - 248°F)
Material： Brass and gold plated
This product was added to our catalog on December 16, 2021
PTK-1610, ProTek RC "TruGrip" Maximum Traction Tire Compound (4oz)
The ProTek R/C TruGrip Maximum Compound is ideal for racers looking to break-in new tires and when maximum tire softening is desired. It is a great solution for damp, wet or extra slick track surfaces and cool outdoor temperatures. The Maximum compound is the most "potent" of the three compounds.
This product was added to our catalog on December 16, 2021
PTK-5216, ProTek RC Heavy Duty T-Style Ultra Plug Charge Lead (Male to 4mm Banana)
This is the ProTek R/C Heavy Duty T-Style Charge Lead, featuring a T-style ultra plug on one end connected to 4mm banana plugs with high quality 14awg silicone wire.
This charge lead can be used for heavy duty charging due to the 14awg wire, and can be used to charge at rates more than 20 amps. In total length, the lead measures 8.5 inches (21.6cm) long from end to end.
This product was added to our catalog on December 16, 2021
PTK-5070, ProTek RC QS8 Anti-Spark Connector (1 Male/1 Female)
ProTek RC QS8 Anti-Spark Connectors are a high quality, high current connector that is perfect for high voltage applications. Not only is the connector capable of handling spikes in excess of 300 amps, the design provides an anti-spark connection that eliminates the dreaded POP when you plug in the battery helping to extend the life of the connector. High voltage bashers, speed run enthusiasts and pilots of all disciplines can benefit from this advanced connector technology.
The QS8 connector features 8mm bullets that can accommodate wire up to 6awg, inside a heavy duty nylon/fiber composite housing. Plus, an included plastic wire cap covers the soldered connection and eliminates the need for heat shrink to create an incredibly clean installation that works well, looks great and is easy to manage. NOTE: T-style connector shown in photos is for size reference only, and is not included.
Features:
Anti-Spark Technology Increases Lifespan of Connector
110A Constant/300A Peak Current Rating
8.0mm Gold Plated Brass Bullet
Great for all High Voltage Applications
Nylon/Fiber Composite Housing
Package Includes One Female Connector, One Male Connector & End Cap
Specifications:
Connector Diameter: 8.00mm
Metal Material: Gold Plated Brass
Plastic Material: Fiber Nylon Comp
Flame retardant rating: UL94 V0
Temperature Range: 200C Max
Rated Voltage: 600V DC
Continuous Current: 110A
Peak Current: 300A+
Weight: 41g (Male+Female Set)
Total Length: Approx 70mm (Male & Female w/End Cap)
Width: 29.5mm
Max Wire Gauge: 6awg
Includes:
(1) QS8 Female Anti-Spark Connector
(1) QS8 Male Antispark connector
(2) Wire Caps
NOTE: T-style connector shown in photos is for size reference only, and is not included.
This product was added to our catalog on December 16, 2021
PTK-5235, ProTek RC EC3 Style to T-Style Ultra Plug Adapter (Female EC3/Male Ultra)
This is a female EC3 style plug to male T-Style Ultra plug adapter from ProTek R/C.
This product was added to our catalog on October 9, 2021
PTK-2112, ProTek RC 30x30x10mm Aluminum High Speed HV Cooling Fan (Blue/Black)
The ProTek RC 30x30x10mm Aluminum High Speed HV Cooling Fan is a great option to keep your ESC and motor temps in check. The fan features a machined aluminum case that helps to dissipate heat, allowing cooler operation of the fan motor at high voltage specs. Plus the aluminum frame work adds strength to the assembly, helping protect the fan blades in the event of a crash.
The fan is a true 2S HV component, that has been built to last with dual ball bearings, and pre-wired 30mm long 2 pin JST connector. Plus, we include a 200mm long adapter plug that allows you to connect the fan directly to the receiver or another source of power. The fan can be mounted directly to the chassis with double side tape, or by using an optional fan mount (not included).
NOTE: This fan should be installed at least 5mm away from the motor to allow sufficient air flow and prevent magnet interference.
Features:
30mm aluminum cooling fan
Ideal for ESC and motor applications
Aluminum casing helps protect the fan blades
Compatible with 2S HV LiPo systems (8.75V max)
Anodized black with blue chamfered edges
Perfect for 1/12, 1/10 and 1/8 scale platforms
2 pin JST connector and included extension for easy installation
Product Model
High Speed HV Cooling Fan
Application
1/12 - 1/8 Motor & ESC
Fan Speed
28,000 RPM
Dimensions (LxWxH)
31x31x10.5mm
Mounting Pattern
24x24mm
Material
Aluminum Case w/Plastic Fan
Weight
12.5g
Operation Voltage
5V - 8.75V
Connector
2 Pin JST
Current
0.45A
This product was added to our catalog on December 16, 2021
PTK-5141-22, ProTek RC 2S 50C 1100mAh Losi Mini T/B & JRX2 LiPo Battery w/EC2 Connector
The Protek R/C 2S 50C 1100mAh Losi Mini T/B and JRX2 LiPo Battery is built with performance in mind. Using Silicon Graphene technology this battery packs a punch with it's 50c discharge rating! Designed to work with the Losi Mini T, B and Mini JRX2 this pack offers extended runtimes with it's larger 1100mah capacity. Equipped with an EC2 style connector makes this a plug in option with no need to mess with adapters or to get out the soldering iron. With more time on the track and the ability to dish out the power this Protek battery pack is an excellent upgrade for your Mini T, B or JRX2 vehicles.
Features:
Direct fit for Losi Mini B, T and JRX2 vehicles
More runtime, with a dramatic increase in punch
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Factory installed EC2 plug
Battery Model
2s 50C 1100mAh
Application
Air, Ground
Type
Silicon Graphene
Voltage
7.4V nominal
Capacity @7.4V
1100mAh
Weight
68g
Connector Type
EC2
Balance Connector
XH Connector
Number of Cells
2 Cell
Configuration
2S1P
Dimensions (LxWxH)
58x32x20mm
Maximum Charge Rate
4C (4.4A)
Watt Hour @7.4V
8.14Wh
Includes:
(1) ProTek R/C Battery
This product was added to our catalog on September 1, 2022
PTK-8243, ProTek RC "TruTorque" Metric 1/4" Power Drill Tip Set (4) (1.5, 2.0, 2.5, 3.0mm)
This is a ProTek R/C "TruTorque" Metric Power Tool Tip Set, with 1.5, 2.0, 2.5 and 3.0mm tips. No one wants to spend money on low quality tools. Tools are an investment that should not be taken lightly and are one of the few items that should outlast the life of the model you are working on...and remain with you for years after. With so many choices available, the decision can be overwhelming. So ProTek R/C has stepped up again, expanding its product line with a complete range of affordable, high quality tools that help to make the decision a little easier.
Anyone who has used a cordless drill to wrench on their rig knows that when used properly, power tools can provide an incredible advantage. They not only allow you to replace damaged parts faster, but also help to prevent hand fatigue. ProTek R/C "TruTorque" Power Tool Tips are machined from high quality HSS steel for durability and long life. The precision cut tips provide an exceptional fit with the fastener. The 1/4" drive hex ends are designed to fit tools that accept a 1/4" drive hex socket.
When it comes to high quality products that are backed by incredible customer support, ProTek R/C has you covered with the products you need to keep your rig ready for action, no matter what.
Features:
Quality tool steel tips
Standard 1/4" drive for compatibility with common power tools
Size is marked on the tip for identification
Specifications:
Total Length: 85mm
Tip Length: 54mm
Material: HSS Steel
Includes:
(1) 1.5mm 1/4" Drive Power Tool Tip
(1) 2.0mm 1/4" Drive Power Tool Tip
(1) 2.5mm 1/4" Drive Power Tool Tip
(1) 3.0mm 1/4" Drive Power Tool Tip
This product was added to our catalog on December 16, 2021
PTK-5350, ProTek RC Heavy Duty EC5 Charge Lead Adapter (Male EC5 to Female XT60)
The ProTek R/C Heavy Duty EC5 Charge Lead Adapter features a "male" EC5 connector with male bullets, connected to a female XT60. Thanks to the 4 inch long 14awg wire, this adapter can be used for heavy duty charging and can handle charge rates more than 20 amps. This adapter can also be used for ESC to battery connections in some applications, allowing you to connect your EC5 equipped battery to an ESC with an XT60.
This product was added to our catalog on December 16, 2021
PTK-8485, ProTek RC Exactness High Grip Hobby Knife (#11 Blade)
The ProTek RC Exactness High Grip Hobby Knife is a great option for cutting or trimming plastic, polycarbonate, rubber, paper and wood. The soft handle has a hex nut on the adjusting end to keep the handle from rolling away but still allowing for a comfortable round handle. Using number 11 blades, this hobby knife also features a blade cover for safe storage and transport. Package includes one hobby knife and one blade.
Features:
Sharp, Long lasting #11 blade
Soft, no slip handle
Non-roll design
Replacement blades available (PTK-8487)
This product was added to our catalog on September 30, 2022
PAAPT42, Pacer Technology Z-42 Blue Thread Locker (0.20oz)
This is a 6ml (0.20 fl. oz.) bottle of Z-42 blue Thread Locking adhesive from Pacer Technologies. If you race Nitro vehicles, you will need lots of this stuff to keep any metal on metal screws from vibrating loose. Best preventative measure you can do to you car is to make sure screws are locktite'd down, so you can finish those long mains! Blue thread locking adhesive is not permanent and will not permanently bond the screws. If you are having a hard time removing thread locked screws, use some heat from a heat gun as thread lock will break down under high temperatures.
This product was added to our catalog on June 6, 2023
PTK-2111, ProTek RC 30x30x10mm Aluminum High Speed HV Cooling Fan (Silver/Black)
The ProTek RC 30x30x10mm Aluminum High Speed HV Cooling Fan is a great option to keep your ESC and motor temps in check. The fan features a machined aluminum case that helps to dissipate heat, allowing cooler operation of the fan motor at high voltage specs. Plus the aluminum frame work adds strength to the assembly, helping protect the fan blades in the event of a crash. The fan is a true 2S HV component, that has been built to last with dual ball bearings, and pre-wired 30mm long 2 pin JST connector. Plus, we include a 200mm long adapter plug that allows you to connect the fan directly to the receiver or another source of power. The fan can be mounted directly to the chassis with double side tape, or by using an optional fan mount (not included).NOTE: This fan should be installed at least 5mm away from the motor to allow sufficient air flow and prevent magnet interference. Features:
30mm aluminum cooling fan
Ideal for ESC and motor applications
Aluminum casing helps protect the fan blades
Compatible with 2S HV LiPo systems (8.75V max)
Anodized black with silver chamferred edges
Perfect for 1/12, 1/10 and 1/8 scale platforms
2 pin JST connector and included extension for easy installation
Product Model High Speed HV Cooling Fan
Application 1/12 - 1/8 Motor & ESC
Fan Speed 28,000 RPM
Dimensions (LxWxH) 31x31x10.5mm
Mounting Pattern
24x24mm
Material
Aluminum Case w/Plastic Fan
Weight
12.5g
Operation Voltage
5V - 8.75V
Connector 2 Pin JST
Current 0.45A
This product was added to our catalog on December 16, 2021
PTK-5117-22, ProTek RC 2S 130C Low IR Si-Graphene + HV LCG Shorty LiPo Battery (7.6V/4800mAh) w/5mm Connectors (ROAR Approved)
The ProTek R/C 2S 130C Graphene + HV 4200mAh Shorty LiPo Battery is a great battery option for anyone looking for a lightweight, shorty style battery. Weighing only 170 grams, the HV Shorty is lighter than a standard shorty pack, with a massive increase in capacity. When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage.
This pack is ideal pack for 2WD and 4WD modified racing, or stock class racers that want optimum voltage for the entire run. This pack is also a great choice for 1/8 e-buggies that want to run a lightweight 2x2S saddle pack configuration. The improved efficiency of this pack will allow for lower operating temperatures and lower internal resistance. This gives users a more consistent battery pack. ProTek Graphene + 130C Packs deliver the power needed by serious racers and enthusiasts alike.
Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for racers and bashers that demand the absolute best.
Features:
Lighter than a hardcase 2S LiPo pack of equal capacity
More runtime, with a dramatic increase in voltage and punch
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Increased run time, increased cycle life and increased voltage!
More capacity gram for gram when compared to standard LiPo cells
Perfect for stock class racers looking to shave grams
10C max charge rates - 1C charge rate recommended for longest life
7.6V nominal voltage
5mm bullets and 5mm to 4mm bullet adapters included
NOTE: While these batteries are LiHV cells, they can still be charged the same as a standard LiPo with a standard LiPo charger. The overall voltage and capacity will be slightly less than when charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the flat discharge curve, reduced weight and low internal resistance. When charged to 8.4V, these packs will still offer a noticeable advantage when compared to a standard 7.4V LiPo pack.
Battery Model
2S HV LiPo
ROAR Approved
Yes
Type
Silicon Graphene
Voltage
7.6V
Capacity @7.4V
4200mAh
Capacity @7.6V
4800mAh
Weight
170g
Connector Type
5mm Bullet
Balance Connector
2mm Bullet
Number of Cells
2 Cell
Configuration
2S1P
Dimensions (WxLxH)
47x96x20mm
Maximum Charge Rate
10C (48A)
Burst Current
130C
Watt Hour @7.6V
36.5 Wh
Includes:
(1) ProTek R/C Battery
(2) 5mm to 4mm Bullet Reducers
(2) 5mm Bullet Connectors
(1) 2mm Balance Bullet Connector
This product was added to our catalog on May 21, 2023
PTK-8073, ProTek RC Steel Mod 1 Pinion Gear (5mm Bore) (20T)
ProTek R/C Steel Mod 1 Pinion Gears are an affordable pinion gear option that doesn't skimp on quality. CNC machined from hardened steel material, these precision cut gears are durable and are perfect for any Mod 1 pitch application. Available in 11 - 20 tooth variants, these gears feature a 5mm bore with the tooth count engraved on the gear for easy identification. Plus, each gear includes a setscrew to make installation easy.
This product was added to our catalog on December 16, 2021
PTK-8487, ProTek RC Replacement #11 Hobby Knife Blades (10pcs)
ProTek RC Replacement #11 Hobby Knife Blades. These replacement blades are intended for the ProTek RC Hobby Knife (PTK-8485), or for any hobby knife requiring a #11 blade. Package includes ten blades.
This product was added to our catalog on September 30, 2022
PTK-8486, ProTek RC Sprue Side Cutter
The ProTek RC Sprue Cutter is a great option for cutting plastic parts free, modifying tire pins and even thin gauge wire. Made from hardened stainless steel, these cutters feature comfortable grips with a heavy-duty return spring for better cutting control. Package includes one sprue cutter.
Features:
Precision cut blades with tapered edge
Made from hardened stainless steel
Comfortable soft grips
Perfect for cutting parts and trimming tires
This product was added to our catalog on September 30, 2022
PTK-7604, ProTek RC "SureStart" Pencil Style Glow Igniter (AA Battery)
This is the ProTek R/C "SureStart" Pencil Style Glow Ignitor. The SureStart pencil ignitor is a high quality glow ignitor that uses a AA size alkaline or rechargeable battery. This ignitor is great for surface and aircraft applications, due to its compact size and 2.25" reach. The blue anodized aluminum handle is easy to spot in your pit bag, and when properly maintained will withstand years of use.
This product was added to our catalog on March 16, 2021
PTK-5114-22, ProTek RC 2S 130C Low IR Si-Graphene + HV Shorty LiPo Battery (7.6V/6400mAh) w/5mm Connectors (ROAR Approved)
The ProTek R/C 2S 130C Graphene + HV 6400mAh Shorty LiPo Battery is a great battery option for anyone looking for a lightweight, shorty style battery. Weighing only 219 grams, the HV Shorty is lighter than a standard shorty pack, with a massive increase in capacity. When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage.
This pack is ideal pack for 2WD and 4WD modified racing, or stock class racers that want optimum voltage for the entire run. This pack is also a great choice for 1/8 e-buggies that want to run a lightweight 2x2S saddle pack configuration. The improved efficiency of this pack will allow for lower operating temperatures and lower internal resistance. This gives users a more consistent battery pack. ProTek Graphene + 130C Packs deliver the power needed by serious racers and enthusiasts alike.
Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for racers and bashers that demand the absolute best.
Features:
Lighter than a hardcase 2S LiPo pack of equal capacity
More runtime, with a dramatic increase in voltage and punch
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Perfect for stock class racers looking to shave grams
10C max charge rates - 1C charge rate recommended for longest life
NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in overheated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for the first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use a battery that has too low a voltage. Do not expose batteries to sunshine or store/charge batteries at temperatures above 35°C or in a closed car. The high-temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging, or racing, do not charge it until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on January 2, 2024
PTK-7805, ProTek RC Aluminum Servo Horn (25T-Futaba, Orion, Savox and ProTek)
This is a ProTek R/C Aluminum Servo Horn, and is intended for use with any servo that uses a 25 tooth spline output shaft. This extremely tough servo-horn has been machined from a solid block of aluminum for incredible precision, rigidity and durability. This horn features a 3mm thick arm for durability, has 19mm hole spacing and uses 3mm hardware to suit the geometry and hardware requirements of most vehicles.
Features:
19mm hole spacing (measured from output shaft screw hole, to linkage rod holes, center to center)
3mm thick arm
27.25mm Overall length
Linkage holes threaded for 3mm hardware
25T Spline Futaba/Orion/Savox/ProTek Output Shaft
Note: Due to manufacturer tolerances, this servo horn may be a tight fit with certain servo brands.
This product was added to our catalog on December 16, 2021
PTK-5041, ProTek RC Sheathed T-Style (Deans) Plug (1 Male/1 Female)
These ProTek R/C Sheathed T-Style Connectors are compatible with any standard generic T-Style plug, as well as Deans Ultra Plugs. These connectors feature a plastic protective sheath that snap onto the back of the connector concealing the solder joint.
Typical t-style plugs use shrink tubing which works fine, but provides a one-time solution. Using the sheath, you can snap it on or off to make any connector changes or modification, as well as create a sleek and professional look.
Package includes one male plug, one female plug and two protective sheaths.
Features:
T-Style connectors
60A max current
Sheathed backing
Concealed solder joint
Labeled polarity
Professional looks
Specifications:
Rated Current： 36A
Max Current: 60A
Internal Resistance: 0.4mΩ
Net Weight (pair): 5.6g
Recommended Wire: 12AWG
Pulling Force: 25N
Recommended Use: 1000 times
Rated Temperature： -20°C - 120°C (-4°F - 248°F)
Material： Brass and gold plated
This product was added to our catalog on March 16, 2021
PTK-5071, ProTek RC QS8 Anti-Spark Connector (1 Male)
ProTek RC QS8 Anti-Spark Connectors are a high quality, high current connector that is perfect for high voltage applications. Not only is the connector capable of handling spikes in excess of 300 amps, the design provides an anti-spark connection that eliminates the dreaded POP when you plug in the battery helping to extend the life of the connector. High voltage bashers, speed run enthusiasts and pilots of all disciplines can benefit from this advanced connector technology.The QS8 connector features 8mm bullets that can accommodate wire up to 6awg, inside a heavy duty nylon/fiber composite housing. Plus, an included plastic wire cap covers the soldered connection and eliminates the need for heat shrink to create an incredibly clean installation that works well, looks great and is easy to manage. NOTE: T-style connector shown in photos is for size reference only, and is not included.
Features:
Anti-Spark Technology Increases Lifespan of Connector
110A Constant/300A Peak Current Rating
8.0mm Gold Plated Brass Bullet
Great for all High Voltage Applications
Nylon/Fiber Composite Housing
Package Includes One Male Connector & Wire Cap
Specifications:
Connector Diameter: 8.00mm
Metal Material: Gold Plated Brass
Plastic Material: Fiber Nylon
Flame retardant rating: UL94 V2
Temperature Range: -20C to +100C
Rated Voltage: 600V DC
Continuous Current: 110A
Peak Current: 300A
Weight: 20g ea (40g Male+Female Set)
Length: 35.9mm w/end capWidth:
Width: 29.5mm
Total Length When Connected: Approx 70mm (Male & Female w/End Cap)
Max Wire Gauge: 6awg
Includes:
(1) QS8 Male Anti-Spark Connector
(1) Wire Cap
This product was added to our catalog on March 24, 2021
PTK-5115-22, ProTek RC 2S 130C Low IR Si-Graphene + HV LCG LiPo Battery (7.6V/6300mAh) w/5mm Connectors (ROAR Approved)
The ProTek R/C 2S 130C Graphene + HV 6300mAh LiPo Battery is the perfect battery option for anyone looking for a lightweight and high capacity LiPo battery. Weighing only 271 grams, this 2S pack is lighter than a standard 2S pack, with much higher capacity. These advancements lead to increase in both voltage and punch throughout a run.
This battery has been designed to improve power to weight ratios while maintaining a low CG. The improved efficiency of this pack will allow for lower operating temperatures and lower internal resistance. This gives users a more consistent battery pack. ProTek Graphene + 130C Packs deliver the power needed by serious racers and enthusiasts alike.
Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for racers and bashers that demand the absolute best.
Features:
Lighter than a hardcase 2S LiPo pack of equal capacity
Improved power to weight ratio and a lower overall CG
More runtime, with a dramatic increase in voltage and punch
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Increased run time, increased cycle life and increased voltage!
More capacity gram for gram when compared to standard LiPo cells
Perfect for stock class racers looking to shave grams
10C max charge rates - 1C charge rate recommended for longest life
7.6V nominal voltage
5mm bullets and 5mm to 4mm bullet adapters included
NOTE: While these batteries are LiHV cells, they can still be charged the same as a standard LiPo with a standard LiPo charger. The overall voltage and capacity will be slightly less than when charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the flat discharge curve, reduced weight and low internal resistance. When charged to 8.4V, these packs will still offer a noticeable advantage when compared to a standard 7.4V LiPo pack.
Battery Model
2S HV LiPo
ROAR Approved
Yes
Type
Silicon Graphene
Voltage
7.6V nominal
Capacity @7.4V
5500mAh
Capacity @7.6V
6300mAh
Weight
271g
Connector Type
5mm Bullet
Balance Connector
2mm Bullet
Number of Cells
2 Cell
Configuration
2S2P
Dimensions (WxLxH)
47x139x22.5mm
Maximum Charge Rate
10C (61A)
Burst Current
130C
Watt Hour @7.6V
47.9 Wh
Includes:
(1) ProTek R/C Battery
(2) 5mm to 4mm Bullet Reducers
(2) 5mm Bullet Connectors
(1) 2mm Balance Bullet Connector
LITHIUM POLYMER SAFETY INFORMATION
IMPORTANT:
DO NOT leave the battery in your model when charging
DO NOT leave unattended when charging
ALWAYS balance charge the battery
ALWAYS use a LiPo charging bag
YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)
YOU MUST not over discharge the Li-Poly battery pack
READ & UNDERSTAND the instructions carefully before operating this battery
NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on January 24, 2022
PTK-5059, ProTek RC EC2 Connector (1 Male/1 Female)
Protek R/C EC2 Connectors. Package includes one male, and one female connector housing, with male and female bullets.
This product was added to our catalog on December 16, 2021
PTK-5102-22, ProTek RC 2S 130C Low IR Si-Graphene + HV Shorty LiPo Battery (7.6V/5000mAh) w/5mm Connectors (ROAR Approved)
The ProTek R/C 2S 130C Graphene + HV 5000mAh Shorty LiPo Battery is a great battery option for anyone looking for a lightweight, shorty style battery. Weighing only 207 grams, the HV Shorty is lighter than a standard shorty pack, with a massive increase in capacity. When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage.
This pack is ideal pack for 2WD and 4WD modified racing, or stock class racers that want optimum voltage for the entire run. This pack is also a great choice for 1/8 e-buggies that want to run a lightweight 2x2S saddle pack configuration. The improved efficiency of this pack will allow for lower operating temperatures and lower internal resistance. This gives users a more consistent battery pack. ProTek Graphene + 130C Packs deliver the power needed by serious racers and enthusiasts alike.
Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for racers and bashers that demand the absolute best.
Features:
Lighter than a hardcase 2S LiPo pack of equal capacity
More runtime, with a dramatic increase in voltage and punch
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Increased run time, increased cycle life and increased voltage!
More capacity gram for gram when compared to standard LiPo cells
Perfect for stock class racers looking to shave grams
10C max charge rates - 1C charge rate recommended for longest life
7.6V nominal voltage
5mm bullets and 5mm to 4mm bullet adapters included
NOTE: While these batteries are LiHV cells, they can still be charged the same as a standard LiPo with a standard LiPo charger. The overall voltage and capacity will be slightly less than when charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the flat discharge curve, reduced weight and low internal resistance. When charged to 8.4V, these packs will still offer a noticeable advantage when compared to a standard 7.4V LiPo pack.
Battery Model
2S HV LiPo
ROAR Approved
Yes
Type
Silicon Graphene
Voltage
7.6V
Capacity @7.4V
4500mAh
Capacity @7.6V
5000mAh
Weight
207 g
Connector Type
5mm Bullet
Balance Connector
2mm Bullet
Number of Cells
2 Cell
Configuration
2S2P
Dimensions (WxLxH)
47x96x25mm
Maximum Charge Rate
10C (50A)
Burst Current
130C
Watt Hour @7.6V
38.0 Wh
Includes:
(1) ProTek R/C Battery
(2) 5mm to 4mm Bullet Reducers
(2) 5mm Bullet Connectors
(1) 2mm Balance Bullet Connector
LITHIUM POLYMER SAFETY INFORMATION
IMPORTANT:
DO NOT leave the battery in your model when charging
DO NOT leave unattended when charging
ALWAYS balance charge the battery
ALWAYS use a LiPo charging bag
YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)
YOU MUST not over discharge the Li-Poly battery pack
READ & UNDERSTAND the instructions carefully before operating this battery
NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on January 24, 2022
