Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 65 Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Whoop Micro Frame kit and HappyModel Mobula6 Whoop frame.
Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 65mm whoop frame, and that will serve as your protection for your motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
Check out our other Micro frames, and our Fractal Engineering Products!
Features
65mm diagonal, squished X geometry, for 31mm props
1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction
Low-profile camera mount, no props in view, no tilt offset
Low Center of gravity, by bringing the AIO closer to the frame/motors
Allows mounting with USB pointing up for easy accelerometer calibration
No need for a canopy as all electronics are tucked safely between the ducts
Maximum rigidity where it matters most; connecting the motors to the FC
Easy maintenance, break one duct, replace only the single duct
Recommended Part List
Gemfan Durable 1210 Bi-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft)
Gemfan 1219-3 Durable Tri-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft) - Choose Your Color
HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
FEA optimization test preformed ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 1.6g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 Pro was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 65 Pro Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Pro Whoop Micro Frame Kit and Meteor65 Pro Whoop frame.
Note: This is designed for prop guards that fit 35mm props like the Meteor65 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
The Pro version has been squished to the max to fit 35mm props with Meteor 65 Pro ducts.
Check out our other Micro frames, and our Fractal Engineering Products!
Features
A variant of the Fractal 65 frame kit
Squished to the max to fit 35mm props with Meteor 65Pro ducts
Maintains 65mm motors distance to meet racing specs
Still fits the camera between the front ducts 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction
Low-profile camera mount, no props in view, no tilt offset
Low Center of gravity, by bringing the AIO closer to the frame/motors
Allows mounting with USB pointing up for easy accelerometer calibration
No need for a canopy as all electronics are tucked safely between the ducts
Maximum rigidity where it matters most; connecting the motors to the FC
Easy maintenance, break one duct, replace only the single duct
Recommended Part List
BetaFPV Gemfan 1406 Tri-Blade 35mm Micro/Whoop Prop 4 Pack (1mm Shaft) - Choose Your Color
HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 1.8g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 75 whoop micro Frame Kit Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Whoop Micro Frame Kit and HappyModel Mobula7 V4 Whoop frame.
Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 75mm whoop frame, and that will serve as your protection for you motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
Check out our other Micro frames, and our Fractal Engineering Products!
Features
75mm diagonal, squished X geometry, for 40mm props
1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction. Cut from Japanese T300 CF sheet
Low-profile camera mount, no props in view, no tilt offset
Low Center of gravity, by bringing the AIO closer to the frame/motors
Allows mounting with USB pointing up for easy accelerometer calibration
No need for a canopy as all electronics are tucked safely between the ducts
Maximum rigidity where it matters most; connecting the motors to the FC
Easy maintenance, break one duct, replace only the single duct
Lightweight, about 21g with HM DiamondF4
Recommended Parts List
HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack - Grey
HappyModel RS 0802 20,000Kv Micro Motor - Choose Version
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 2.1g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
From motorpost to motorpost on this frame, the distance is 84mm.
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 Pro Max was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 75 Pro Max whoop micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Pro Max Whoop Micro-frame kit and BetaFPV Meteor75 Pro Whoop Frame.
Note: This is designed for prop guards that fit 45mm props like the Meteor75 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
The Pro Version has been scaled to the max to fit 45mm props
Check out our other Micro frames, and our Fractal Engineering Products!
Features
A completely new variant of the F75, but this is actually 84mm motorpost to motorpost distance.
The same winning recipe, scaled to fit 45mm props with ducts while keeping the camera up front
Extended camera mount to reduce prop guards in view
Low center of gravity, by bringing the AIO close to the frame/motors
Allows mounting with USB pointed up for easy accelerometer calibration
Easy maintenance, break a duct, replace only the single duct
No need for a canopy as all electronics are tucked safely between the ducts
Approximately 21g using the Happymodel DiamondF4 AIO
Recommended Parts List
Gemfan Ducted 1815 Tri-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color
Gemfan Ducted 1815 Bi-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color
HappyModel RS 0802 20,000Kv Micro Motor - Choose Version
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
HappyModel OVX300 25-300mW 5.8GHz U.Fl VTX w/ OpenVTX
FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 2.21g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
Introducing... the GEPRC SMART 16 Freestyle Frame Kit!
The GEPRC Smart 16 1.6" Nano Freestyle Frame is a tiny, lightweight freestyle FPV addition to the GEPRC Phantom series. The SMART 16 continues the consistent lightweight design concept of the Phantom series. The 1.5mm carbon fiber arm, with a 1mm top plate, creates a balance point that is maintained between the strength of the fuselage and the weight of the whole drone which allows it to be lightweight and tough at the same time. The M1.4 Motors mounting holes can be used to install small 3-hole brushless motors to reduce the weight of the body. Good arm width contributes to high durability. This design is great for freestyle flying, with no props in view!
Thanks to the 3D printed parts, the frame weighs only 8.5g, saving a lot of overall weight. The independent battery compartment is designed to stick the battery on top and below the drone making it very convenient and fast to replace batteries.
Check out our other Micro frames And our whole GEPRC product line!
Specifications
Frame Style: Toothpick
Top plate thickness: 1.0mm
Bottom plate thickness: 1.5mm
Camera plate thickness: 1.0mm
Stack Size 16x16mm
Motor Mount: 6mm Tri 08xx
Camera Mount: 14mm Nano
Weight: 8.5g (including 3D prints)
Recommended:
Motor: GEPRC SPEEDX2 0803 11000Kv Micro Motor
AIO: GEPRC F4 V1.4 2-4S AIO Flight Controller
Prop: HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack
LiPo: RDQ Series 350mah 2S 50C/100C 7.6V HV XT30 Micro Battery
Includes
1x GEPRC SMART 16 1.5mm Bottom Plate
2x GEPRC SMART 16 1mm Camera Plate
1x GEPRC SMART 16 1mm Top Plate
2x 120mm LiPo Strap
1x 3D Printed Part Set
1x Screwdriver Set
1x Hardware Set
2x Battery Pad
The world’s first AIO 5in1 F4 flight controller with an integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter, and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency, this flight controller is what all Race/Freestyle pilots need. It is suitable for whoop Race or Toothpick Freestyle, and can also be used in the 1S ultra-lightweight Nano Long Range platform.
Check out our other whoop flight controllers, and the rest of our Happymodel offerings.
Specifications
HappyModel ELRS 2G4 Whoop Flight Controller
MCU: STM32F411CEU6
Gyro: ICM20689
Input Voltage: 1S (2.9-4.35V)
Firmware Target: CRAZYBEEF4SX1280
Onboard ESC
MCU: EFM8BB21Input Voltage: 1S (2.9-4.35V)
Current: 5A continuous peak 6A (3 seconds)
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT600
Onboard 2.4GHz ExpressLRS Receiver
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS. Could bind with Happymodel ES24TX, ES24TX Lite, ES24TX Slim, and DIY 2.4GHz ELRS TX module (need to flash the same version ELRS firmware)
Onboard 5.8HGz VTX
Output power: 25-200mw switchable
Frequency: 5.8GHz 5bands 40 channels(include Race band) Smart audio ready
Current consumption: 300mA
Includes
1x HappyModel 1S F4 AIO Toothpick/Whoop Flight Controller w/ 5A 8bit 4in1 ESC & 200mW VTX - ELRS 2.4GHz SPI
1x Connecting Wire
1x Dipole Antenna
4x Damping Balls
1x 3-Pin Wire
5x Screws
Downloads
Firmware
The Happymodel 1S Balance Charging Board allows you to charge up to four 1S LiPo batteries with PH2 connector at the same time.
The board supports a maximum 1.5A charging current but charge at 1C to be safe. This method of charging is a little safer then parallel charging as it allows the charger to individually monitor and balance each cell.
This is a great charger for anyone that would like to charge 1s liPos for your Mobula, Moblite or Mobeetle!
Check out our other charging accessories, as well as the rest of our HappyModel gear!!
Specifications
Input Voltage: 1S
Max Amperage: 1.5A
Dimensions: 81x46x20mm
Weight: 35g
Includes
1x HappyModel 1S Series LiPo Balance Charging Board
EP1 Dual ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver apply “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments make these TCXO much reliable.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Type: ISM2.4GHz
ESP32 PICO D4, dual SX1280(SX1281)
Antenna connector: IPEX MHF 1/U.FL
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: >19dbm
Receiver protocol: CRSF
Input voltage: +5V DC @ “+” pad
PCB size: 19mm x 14mm
Weight: 1gram exclude antenna
Built-in a TCXO (temperature compensated crystal oscillator)
Firmware
Default Firmware out of factory: Unified_ESP32_2400_RX Could upgrade to HappyModel EP1 Dual 2400 RX 3.0FW
Firmware update via UART or WIFI
Includes
1x Happymodel 2.4G ExpressLRS EP1 Dual TCXO RX True Diversity Receiver Module
2x Antennas
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that’s too simple. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for whoop because of the ultra light and Nano size.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Packet Rate: 25/50/150/250/500Hz
RF Frequency: 2.4GHz
Antenna: Ipex 4
Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX
Includes
1x HappyModel EP1 RX Express LRS Receiver
1x Short antenna
1x Long antenna
EP1 ELRS receiver is the hottest ExpressLRS receiver since it was released. Now the new TCXO version EP series receiver applies a “temperature compensated crystal oscillator”, accurate frequency and excellent performance in extreme temperature environments making these TCXO much more reliable.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Type: ISM2.4GHz
SX1280(SX1281)IMLTRT RF Module
Antenna connector: IPEX MHF 1/U.FL
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: >19dbm
Receiver protocol: CRSF
Input voltage: +5V DC @ “+” pad
PCB size: 10mm x 10mm
Weight: .04 grams excluding antenna
Built-in a TCXO (temperature-compensated crystal oscillator)
Includes
1x HappyModel 2.4GHz EP1 TCXO RX Express LRS Receiver
2x Antennas
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that’s too simple. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for whoop because of the ultra light and Nano size.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Packet Rate: 25/50/150/250/500Hz
RF Frequency: 2.4GHz
Antenna: SMD Ceramic antenna
Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX
Includes
1x HappyModel 2.4GHz EP2 RX Express LRS Receiver - For Sale At RaceDayQuads
The Happymodel EP2 TCXO RX is a nano-sized true diversity 2.4GHz ELRS receiver with RF amps. This TCXO Rx receiver uses a temperature-compensated crystal oscillator to help with accurate MCU clock frequency, thus improving the performance and reliability of your RC link. Despite the small size, the low latency and high refresh rate of the ELRS system allow this receiver to be used on full-size/long-range quads, while also being small enough to be used on whoop-size quads! The Happymodel EP1 RX includes an IPEX connector for a dipole antenna, while the EP2 RX includes a built-in SMD antenna.
The EP1, EP2, and EP1 Dual modules are based on the ESP8285 MCU that allows for upgrading via WiFi, along with the SX1280(SX1281)IMLTRT RF Module.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Type: ISM2.4GHz
ESP8285 MCU
SX1280(SX1281)IMLTRT RF Module
Antenna connector: SMD Ceramic antenna
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: >19dbm
Receiver protocol: CRSF
Input voltage: +5V DC @ “+” pad
PCB size: 10mm x 10mm
Weight: 1gram exclude antenna
Built-in a TCXO (temperature-compensated crystal oscillator)
Firmware
Default Firmware out of the factory: HappyModel_EP_2400_RX V2.2 version
Built-in a TCXO (temperature-compensated crystal oscillator)
Includes
HappyModel 2.4GHz EP2 TCXO RX Express LRS Receiver
This antenna is a perfect replacement for the ERLS or TBS Tracer receivers.
Check out the rest of our ELRS accessories, as well as the rest of our HappyModel selection!
Specifications
Frequency or Freq. Bandwidth: 2.4GHz
Polarization: Linear
Gain: 2.23dBic
Radiation Efficiency: 60.56%
Connection: U.FL / IPEX1
Cable Length: 40mm
Includes
1x HappyModel 24RX40 2.4GHz U.FL Antenna For ELRS and TBS Tracer
This antenna is a perfect replacement for the ERLS or TBS Tracer receivers.
Check out the rest of our ELRS accessories, as well as the rest of our HappyModel selection!
Specifications
Frequency or Freq. Bandwidth: 2.4GHz
Polarization: Linear
Gain: 2.23dBic
Radiation Efficiency: 60.56%
Connection: U.FL / IPEX1
Cable Length: 90mm
Includes
1x HappyModel 24RX90 2.4GHz RC Antenna For ELRS and TBS Tracer - U.FL
All batteries must be shipped by a ground shipping method.
Spare battery for the HappyModel Moblite7 Whoop.
Check out the entire RDQ Series of LiPo and LiHV battery packs!
Specifications
Capacity: 650mAh
Max. Continuous Discharge Rate: 60C
Discharge Lead: 20mm, PH2.0
Dimensions: 60x18x8mm
Weight: 16g
Includes
1x HappyModel 3.8V 1S 650mAh 60C LiHV Micro Battery - PH2.0
Get ready to experience the thrill of FPV racing with the HappyModel Bassline FPV Drone Frame Kit! This high-quality frame kit is designed for maximum performance and durability. It's made of lightweight and durable carbon fiber and comes with all the necessary hardware for easy assembly. Upgrade your FPV racing game with the HappyModel Bassline FPV Drone Frame Kit from RaceDayQuads - order yours today!
Be sure to check out all our Micro Frames, and all our Happymodel products!
Specifications
Wheelbase: 90mm
Mount hole size: 25.5x25.5mm
Size: 115x115x40mm
3K carbon
Motor Mounting: 9x9mm/12x12mm M2
Includes
1x 3K carbon fiber bottom plate
1x 3D Printed battery tray
8x Rubber damping balls
4x M2x16 screw for Bassline mount
4x M2x22 screw for Bassline HD mount
8x M2 Nut
1x Battery Anti-skid Mat
Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season. This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability.
Check out the rest of pre-built quads and our HappyModel selection!
Features
X12 5-IN-1 AIO flight controller w/ built-in receiver and OpenVTX
VTX Power up to 400mw
RS0802 20000KV motors
RunCam Nano 3. The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible with 1S Lipo/LIHV
Specifications
Input Voltage: 1S
Max Continuous Current: 12A
Motors: 0802 20000KV
Camera: RunCam Nano 3
Wheelbase: 75mm
Dimensions: 99x99x40mm
Weight: 24g
Includes
1x HappyModel BNF 1S Mobula 7 Whoop - PNP
The HappyModel BNF 1S Mobula 7 HD Whoop version is a light and efficient 75mm brushless whoop which provides 1080P HD video recording functionality. HappyModel added blackbox for this 1s 75mm HD recording whoop so that you now have gyroflow functionality. Unlock the ultimate smooth flights with a combination of the Mob 7 HD and gyroflow!
Check out the rest of pre-built quads and our HappyModel selection!
Specifications
HappyModel X12 AIO
Input Voltage: 1-2S
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: MPU6000 or ICM20689 or BMI270
Max Continuous Current: 12A
VTX Output Power: 25-400mW
Antenna Connector: U.FL
OSD: Yes
Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX
ESC Firmware: Z_H_30_REV16_7
Mounting Pattern: 25x25mm
Weight: 5.1g
HappyModel RS Motor
Input Voltage: 1S
KV: 20000KV
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension: Φ10.5x13.5mm
Wire length(include connector): 30mm
Weight: 2g
Runcam Split 3 Lite
Video Resolution: 1080@60fps/1080@50fps/1080@30fps/720@60fps
Field of View(FOV): Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video File Format: MOV
Image Resolution: 2MP
Signal System: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Includes
1x HappyModel BNF 1S Mobula 7 HD Whoop
The Crux 35 is an ultra-lightweight 3.5Inch FPV freestyle and racing drone, the weight of the whole drone is only 87g for the analog version and 108g for the digital HD version. The Crux35 series drone use Happymodel's EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
Happymodel Crux35 Racing Drone V2 comes with the CrazyF411 ELRS flight controller. This board comes with an integrated UART 2.4GHz ExpressLRS receiver and 20A BLheli_S ESC(Bluejay firmware pre-installed) which could support 3-4S.
The new V2 version comes with CrazyF411 ELRS AIO flight controller built-in UART ExpressLRS receiver which allows for updating the receiver with ease.
Choose from between ELRS 2.4GHz and FrSky for your receiver.
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Features
Bind tutorial for ELRS
Ultra-lightweight 3.5-inch BNF FPV Freestyle Drone
HD video transmission and analog video transmission are optional
Integrated ExpressLRS UART receiver
High efficiency EX1404 power system
Can be equipped with Naked Gopro or SMO4K
Specifications
Weight: 87g
Brand: Happymodel
Wheelbase: 150mm
Dimensions: 130mmx130mmx45mm
Receiver option: UART ExpressLRS 2.4GHz
HappyModel Flight Controller (ELRS Version)
Input Voltage: 2-4S LiPo
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: BMI270 or ICM42688P (SPI control)
ESC Connections: Yes
Firmware: CrazybeeF4DX
Current Sensor: Yes
Mount pattern: 25.5x25.5mm (M2)
Dimensions: 32x28x9mm
Weight: 5g
Built-in 20A Blheli_s ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1A BEC
Onboard ESC:
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite and ESC-Configurator programmable
Factory firmware: Bluejay 0.18.1
Firmware target: F_H_40_48_v0.18.1
Support DSHOT150/DSHOT300/DSHOT600
Default protocol: DSHOT300
HappyModel EX1404 3500KV Motor
Mode: EX1404
Kv: 3500Kv
Input Voltage: 3-4S LiPo
Configuration: 9N12P
Motor Dimensions: Φ17.8mm x 17.6mm
Stator Dimensions: Φ14mm x 4mm
Shaft Diameter: 1.5mm
Mounting Pattern: Φ9mm
Weight: 9g
HappyModel Propellers
Propeller Diameter: 3.5 inch
Pitch : 2
Blades : 3
Material : Poly Carbonate
Weight : 1.5g
Hub Diameter : 10mm
Hub Thickness: 4.7mm
Shaft :1.9/1.5/1.9mm
Adaptor Rings : NO
Caddx Ant Camera
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC and PAL(switchable)
MENU: Support
IMAGE: 4:3 or 16:9
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio: >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm/F2.5
Minimum illumination: 0.001Lux
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14x14mm
Wide Power Input: DC 3.7-18V
Work Temperature: -20°C~+60C
Work Humidity: 20%~80%
Weight: 1.7g
Happymodel OVX303 5.8G analog VTX or OVX306 5.8G analog VTX
Input Voltage: 5V
RF Output Power: 25-300mW
Antenna Connector: U.Fl
Power/Video Connection: Solder Pads
OVX303 Stack Size: 16x16mm, 20x20mm, 25x25mm
OVX306 Stack Size: 25x25mm
Weight: 0.9~1g
Includes
1x HappyModel BNF Crux35 V2 3.5" Analog Quad - Choose version
1x 5D-OSD menu board
1x Screw Driver and Screw Set
8x HQProp T3.5X2X3Grey (4cw+4ccw)
1x Buckle Velcro for battery
Introducing the Moblite7 Ultralight FPV Brushless Whoop! Made in collaboration with FPV pilot "Mr. Shutterbug," this whoop is one of the lightest 75mm drones on the market! And glows in the dark!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 36g With battery
Propellor Size: 75mm
Antenna: Linear Dipole
HappyModel DiamondF4 FR FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CrazybeeF4F
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (3sec)
ESC Firmware: BLheli_S
Factory firmware: O_H_50_REV16_8.HEX
Stack Size: 25x25mm
Dimensions: 29x29mm
Motors
Stator Size: 0802
Kv: 19000
Weight: 1.7g
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x 75mm Frame (Mobula7 frame)
1x Option1: DiamondF4 FR built-in SPI Frsky receiver
4x EX0802 KV19000 Unibell brushless motor
1x HQPROP 40MMX2 propeller(4cw+4ccw)
1x Runcam Nano3
1x Built-in 5.8G 40ch 25mw-200mw VTX
2x 1s 650mah Lipo battery
1x Propeller disassemble tool
1x Screwdriver
1x Happymodel Carry case
The Happymodel Moblite7 HDZero Whoop is a 75mm HD brushless whoop weighing just 29.5 grams. It features the HDZero Whoop Lite VTX and Nano Camera and a built-in SPI ELRS 2.4GHz or FrSky 2.4GHz receiver. With powerful EX1002 KV20000 motors and a Superbee F4 Lite flight controller, this should be a great performing high-definition whoop you can fly just about anywhere.
UART ELRS v3.0 ready
Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
The lightest 1S 75mm brushless whoop
Powerful and efficiency
The lightest 1S AIO 5IN1 F4 flight controller
1002 brushless motors
Low-profile Canopy design
HD Zero
Specifications
Wheelbase: 75mm
Size: 97x97x25mm
Weight: 19.5g (without battery)
Weight: 36g
Motor
Model: EX EX1002 20000KV
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.Len): Φ13.5mmx12.5mm
Weight(g): 2.5
No.of Cells(Lipo): 1S only
Flight Controller
SPI ELRS version Firmware target: CrazybeeF4SX1280
SPI FRSKY version Firmware target: CrazybeeF4FR
MCU: STM32F411CEU6 (100MHz, 512K FLASH)
Sensor: ICM20689 or ICM42688P or BMI270(SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/ELRSreceiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC
MCU Upgraded to EFM8BB21
Power Supply: 1S LiPo/LiPo HV
Current: 5A continuous, peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory Firmware: O_H_50_REV16_8.HEX
Default Protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version
SPI BUS receiver Frsky D8/D16 compatible
Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt)
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol
Onboard ELRS Receiver Version
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could bind with ELRS V2.0 firmware TX module
Onboard 5.8G 40CH 25-200mW VTX
Output Power: 25mw~200mw switchable
Frequency: 40CH
Input Voltage: 3.3V 5.5V
Current Consumption: 300mA (type)
Frequency: 5.8GHz 5bands 40 channels (include Race band)
Smart-audio Ready
HDZERO NANO LITE CAMERA SPECIFICATIONS:
Dimensions: 14x16x11 mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMOS sensor
Excellent low light performance
FOV:4:3: D:130° H:108° v:84°16:9:D:122° H:108° V:65°
Includes
1 x HappyModel BNF Moblite7 HDZERO 1S 75MM Brushless HD Whoop
1 x Moblite7 Spare Canopy
1 x Gemfan 1610 propeller Set (4cw+4ccw)
1 x Propeller disassemble tool
1 x Screwdriver
All batteries must be shipped by a ground shipping method.
Equipped with an ExpressLRS built-in SPI receiver, you'll never have to worry about range when whooping! This version of the Mobula6 also has another new feature: 0802 19000Kv motors! These motors are some of the lightest brushless whoop motors. Lighter whoops are easier to fly and super fast.
ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable.
This version comes pre-installed with ELRS 2.4GHz and ELRS V2.0!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 18.7g
Recommended Battery: 1S 300mAh
Propellor Size: 65mm
Antenna: Linear Dipole
HappyModel Crazy F4 FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CRAZYBEEF4DX
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (10sec)
ESC Firmware: BLheli_S
Stack Size: 25x25mm
Dimensions: 29x29mm
Weight: 5g
Motors
Stator Size: 0802
Kv: 19000
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x HappyModel BNF Mobula6 ELRS 65mm Brushless Whoop - ELRS 2.4GHz
4x 1S 300mAH Batteries
All product containing lithium batteries must be shipped by a ground shipping method. Please be aware Betaflight 4.3.1 firmware has a bug, Please do not flash version 4.3.1.
This is the V2 version of the Mobula 6 HD. This version features an ICM20689 Gyro as well as an OpenVTX 400mW VTX.
The Highly sought after Mobula6 now comes in HD! Record all your sessions in HD with the onboard RunCam split 3 Lite.We recommend RDQ 1S 300mAh LiPos for this whoop! Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
Extreme light 1S 65mm Brushless HD whoop only 27g
Come with Runcam Split3-lite 1080P HD DVR
Smooth and agile
Compatible for 1S Lipo/LIHV
Camera Angle adjustable
Specifications
Wheelbase: 65mm
Size: 80x80x40mm
Weight: 27g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Internal SPI DSM2/DSMX version(Compatible with SPEKTRUM DSM2/DSMX protocol radio transmitter)
External TBS CRSF NANO version(Compatible with TBS Transmitters)
Motors
Model: EX0802 19000KV
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Shaft Diameter: Φ1mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Weight(g): 1.7g
No.of Cells(Lipo): 1S only
Flight Controller
(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
(DSM2/X SPI RX version) CRAZYBEEX DXS DSM2/X version firmware target: CrazybeeF4DXS
(External TBS CRSF NANO RX version) CRAZYBEE F4 Lite Firmware target: CrazybeeF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G 400mW VTX
Built-in SPI Frsky/Flysky/DSMX receiver
Built-in 5V 1A BEC
Built-in voltage detection
ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band Smart audio ready
Runcam Split3 Lite
Model: RunCam Split3-Lite
Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps
Video File Format: MOV
Image Resolution:2 MP
TV Mode: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
Hole Distance of Installation: 25.5*25.5mm
PCB Size: 29*29mm
Lens Module Size: 14*14mm
Lens Specs: M9
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
Working Current: 450mA @5V
Includes
1x Happy Model BNF Mobula 6 HD 1S Whoop Quad - Choose Your RX
HappyModel has been an amazing company, bringing us FPV enthusiast quality whoops to fly. Take a look at HappyModels first ever whoop on a 85mm frame. It comes with X12 series flight controller, EX1103 KV11000 motors and Gemfan Hurricane 2023 tri-blade propellers, all together gives this whoop an amazing performance for an extremely smooth flight.
Choose between PNP (No RX) and BNF (ELRS SPI 2.4)
Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and OPENVTX
VTX Power up to 400mw
ELRS V2.0 (Default), can be flashed to ELRS V3.0
EX1103 KV110000 motors
CaddxFPV Ant FPV camera
Smooth and powerful
Compatible for 1S-2S Lipo/LIHV battery
3D Printed Camera Lens Protector
User Manuals
ELRS (SPI)
PNP (No RX)
Specifications
Brand Name: Happymodel
Motor: EX1103 KV11000
AIO: X12 5-IN-1 AIO flight controller
Camera: CaddxFPV Ant FPV camera
Prop: Genfan 2023-3 propellers
Weight: 42.7g
Input Voltage: 1-2S
Wheelbase: 85mm
Size: 120mmx120mmx50mm
Motor Specifications
Model: EX1103 KV11000
Configuration: 9N12P
Stator Diamter: 11mm
Stator Length: 3mm
Shaft Diameter: Φ1.5mm
Motor Dimension(Dia.xLen): Φ13.5mmx15.5mm
Weight(g): 3.8g
No.of Cells(Lipo): 1-2S
Propeller Specifications
Weight: 0.88g
Material: PC
Pitch: 2.3inch
Props Dia: 52.17mm
Center Thickness: 5mm
Center Hole Dia: 1.5mm
Flight Controller Specifications
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689 or ICM42688P(SPI connection)
Mount hole size: 25.5mm x 25.5mm
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
Built-in voltage detection
Built-in current sensor
Onboard 4in1 ESC
Power supply: 1-2S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Firmware target: Z_H_30
Default protocol: DSHOT300
Support Bluejay firmware
Onboard SPI ELRS 2.4GHz Specifications
Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could flash FC firmware to support ExpressLRS v3.0 TX module
PNP Version Specifications
Full UART1 for external Receiver
Support CRSF/GHOST/SBUS/IBUS/DSMX protocol
IR1 pad(invert RX1) used for SBUS input
Includes
1x HappyModel BNF Mobula8 1-2S Brushless Analog Whoop - Choose Your Receiver
1x Gemfan Hurricane 2023 tri-blade propellers (4CW+4CCW)
1x Screw Driver
1x Extra camera canopy
Experience powerful performance with the HappyModel BNF Mobula8 1-2S HD 85mm! This amazing quadcopter comes with an amazing DJI O3 Air Unit and Micro Cam, as well as Crazy F405 ELRS HD flight controller, EX1103 11000Kv motors, and Gemfan Hurricane 2023 tri-blade propellers for superior power performance. Get the perfect HD experience with the Mobula8!
Be sure to check out all our pre-built quads, and all our Happymodel products!
Specifications
Camera/VTX: DJI O3 Air Unit
Item Name: Mobula8 1-2S 85mm Micro FPV whoop drone
Size: 120mmx120mmx50mm
Brand Name: Happymodel
Wheelbase: 85mm
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Mount hole size: 25.5mm x 25.5mm
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
MOTORS
Motor Dimension(Dia.xLen):Φ13.5mmx15.5mm
Mode: EX1103 11000Kv
Shaft Diameter:Φ1.5mm
No.of Cells(Lipo):1-2S
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:3mm
Weight(g):3.8g
PROPELLERS
Center Hole Dia:1.5mm
Center Thickness:5mm
Props Dia:52.17mm
Weight:0.88g
Pitch:2.3inch
Material: PC
Includes
1x HappyModel BNF Mobula8 1-2S HD 85mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz
Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card.
Experience powerful performance with the HappyModel BNF Mobula8 1-2S HD 85mm! This amazing quadcopter comes with Crazy F405 ELRS HD flight controller, EX1103 11000Kv motors, and Gemfan Hurricane 2023 tri-blade propellers for superior power performance.
Be sure to check out all our pre-built quads, and all our Happymodel products!
Specifications
Item Name: Mobula8 1-2S 85mm Micro FPV whoop drone
Size: 120mmx120mmx50mm
Brand Name: Happymodel
Wheelbase: 85mm
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Mount hole size: 25.5mm x 25.5mm
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
MOTORS
Motor Dimension(Dia.xLen):Φ13.5mmx15.5mm
Mode: EX1103 11000Kv
Shaft Diameter:Φ1.5mm
No.of Cells(Lipo):1-2S
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:3mm
Weight(g):3.8g
PROPELLERS
Center Hole Dia:1.5mm
Center Thickness:5mm
Props Dia:52.17mm
Weight:0.88g
Pitch:2.3inch
Material: PC
Includes
1x HappyModel BNF Mobula8 1-2S HD 85mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz
Spare replacement Flight Controller for the Happymodel Mobula 6, and an all around incredible little TRUE AIO for any 1S brushless build!
Check out all our Whoop FCs, our Mobula 6 parts selection, and all Happymodel products!
Specifications
Flight Controller
(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
Onboard FrSky SPI D8 Receiver Version
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 model
Channels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Onboard FlySky SPI Receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
Onboard 5.8GHz VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio ready
Includes
1x HappyModel Crazybee F4 Lite 1S Whoop Flight Controller - Choose Your RX
The world's first AIO 5in1 whoop flight controller with built-in ExpressLRS receiver is coming out now. This F4 flight controller has a built-in 5A esc, VTX, OSD, high-performance 900MHz ExpressLRS receiver, it’s best for 1S Long Range and whooping.
Check out our other Whoop/Toothpick flight controllers, as well as the rest of our HappyModel selection!
Specifications
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CRAZYBEEF4DX
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (10sec)
ESC Firmware: BLheli_S
Stack Size: 25x25mm
Dimensions: 29x29mm
Weight: 5g
Includes
1x HappyModel Craz yF4 ELRS 900MHz Whoop/Toothpick AIO Flight Controller w/ 8Bit 5A ESC
An F405 chip FC with built-in Serial ELRS receiver, 4in1 12A ESC, and 8Mbp black box. Optimized layout, supports 1-2S Lipo/LiHV. Perfect for Tinywhoop/Cinewhoop/Toothpick. Betaflight/INAV compatible. 3 sets UARTs, 5V/3A & 9V BECs, barometer. Get performance to elevate your FPV. Experience exceptional agility and power for your racing and freestyle sessions. With this board, you'll have the perfect setup to take your flight to the next level.
Browse the rest of our Whoop AIO Boards and our Happymodel gear.
Specifications:
Brand Name: Happymodel
Item Name: CrazyF405HD ELRS 1-2S AIO Flight controller
Mount size: 25.5mmx25.5mm
Weight: 4.8g without power lead wire
Firmware target: BetaflightF4
Support 1-2S Lipo/LiHV battery
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
*When using 1s battery and high KV 0702/0802 motors, should set the startup power to 1100/1200
Includes
1x HappyModel Crazyf405 ELRS HD 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC & ELRS 2.4GHz RX
1x Power lead with a XT30 Connector
Wiring Diagram
Equip your 2-4S drone with the HappyModel CrazyF411 F4 Flight Controller. Enjoy flying with its 20A 8Bit 4in1 ESC and ELRS 2.4GHz receiver featuring a high-sensitivity SX1280 frequency chip for low latency, high packet rate, and great range. With a big Mosfet that supports up to 20A currents, this controller is perfect for FPV drones and strong enough for race or freestyle flying. This flight controller lets you update firmware through Betaflight pass-through or WIFI. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. The default firmware is ELRS V3.0.1. Get ready to take your drone game to the next level!
Browse the rest of our Whoop AIO Boards and our Happymodel gear.
Features
Integrated serial 2.4GHz ExpressLRS receiver
Pre-installed with Bluejay firmware)
Coming with a BMI270 gyro
Specifications
Flight Controller
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: ICM42688P
Mount pattern: 25.5x25.5 M2
Size: 32x28x9mm
Power supply: 2-4S Lipo battery
Built-in 20A Blheli_S ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1.5A BEC
Flight controller firmware target: CRAZYBEEF4DX
Weight: 4.97
Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay 0.18.1Firmware target: F_H_40_48_v0.18.1
Default protocol: DSHOT150/DSHOT300/DSHOT600
Onboard UART ExpressLRS 2.4GHz Receiver
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1
Onboard voltage and Amperage Meter Settings
Voltage meter scale setting 110
Amperage meter scale setting 470
Includes
1x HappyModel CrazyF411 F4 2-4S Whoop/Toothpick AIO Flight Controller w/ 20A 8Bit 4in1 ESC - ELRS 2.4GHz (UART)
2x Wire
1x Hardware Set
4x Grommets
Wiring Diagram & Binding Procedure
Binding procedure
Supply power to the flight controller by plug USB, wait until the green LED on the FC is off, immediately turn off the power, and then repeat again the above steps. When the FC is powered on for the third time, the green LED light will start to double-flash, which means that the RX enters the binding mode
Please make sure your ExpressLRS tx module firmware is v3.x.x. And go to ExpressLRS.lua from “TOOLS” menu of your radio transmitter. Then hit [Bind] to binding with the onboard ExpressLRS receiver. The green LED should blinking slowly first then turn to solid, that means binding was successfully. If the green led still keep double flash after binding ,please change Model Match tab value from “off” to “on” or from “on” to “off”
Receiver LED status meanings
Green LED solid means bind successful or RC link established; Green LED double-flash means get into bind mode; Green LED flash slowly means no RC signal input from TX module; Green LED continuous flash fast means ExpressLRS wifi enabled.
Bind successful
Bind Mode
No RC Input
Wifi Mode
Replacement part for the HappyModel Crux3
Check out the HappyModel Crux3 Quad and Accessories Collection.
Specifications
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC or PAL Switchable
IMAGE: 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio : >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm
Min. Illumination: 0.001Lux@F1.2
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V
Work Temperature: -20℃~+60℃
Weight: 2g
Includes
1x HappyModel Crux 3 Replacement Camera - Caddx Ant
This is a replacement frame for the Crux 35 Frame.
Check out our other Crux35 accessories, as well as the rest of our HappyModel selection!
Specifications
Wheelbase: 150mm
Main Plate Thickness: 3mm
Top Plate Thickness: 2mm
Stack Size: 20x20mm, 25x25mm
Motor Mount: Φ9mm
Camera Mount: Micro
Weight: 26g
Includes
1x HappyModel Crux35 / Cruz35 HD 3.5" Frame
This is a replacement bottom plate for the Crux35 and Crux35 HD frames.
Check out our other Crux35 accessories, as well as our entire Happymodel selection!
Includes
1x HappyModel Crux 35 Bottom Plate
Another Express LRS receiver but this time, it's PWM capable! The Happymodel ExpressLRS PWM Kit includes a 6CH EPW6 2.4GHz Receiver with two antennas. Perfect for your Fixed Wing airplane!
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Item: Happymodel EPW6 TCXO 2.4GHz PWM receiver
ESP8285, SX1280/1281
Antenna connector: IPEX MHF 1/U.FL
6x PWM outputs
RF Frequency: 2.4GHz (2400~2480MHz)
Telemetry power: 12dbm
Receiver protocol: PWM or CRSF
Input voltage: +5v~8.4v
PCB size: 19mm x 17.5mm
Weight: 1.49g / antenna
Firmware
Target option 1: Generic ESP8285 6xPWM 2.4Ghz RX
PWM receiver via 1~6 PWM outputs
Target option 2: HappyModel_EP_2400_RX
CRSF Serial receiver via TX and RX
Firmware update via WIFI
Includes
1x HappyModel EPW5 2.4GHz ELRS PWM Receiver
2 x 2.4GHz antenna
The ES24TX Pro Micro ExpressLRS TX module is a upgrade version of ES24TX module.Max output up to 1000mw, reserved Cooling Fan and RGB LED module. This Micro TX module support most of the OpenTX radio transmitter that with Micro JR bay. And this time the ES24TX Pro module comes completely assembled before out of factory. If you've considered making the switch to Express LRS, there's no better time than now!
Check out our other ELRS accessories, as well as the rest of our HappyModel selection.
Specifications
Regulatory Domain: ISM2400
MCU: ESP32(main),ESP8285(aux,as espbackpack)
RF chip: SX1281IMLTRT
JR standard 5pin socket
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
RF Output Power: >30dBm
Power supply voltage: 5v~10v
Weight: 51gram(without antenna）
Dimension: 70mm*49mm*32.5mm
Antenna gain: 4.18dBi
Firmware target: HappyModel_ES24TX_Pro_Series_2400_TX
Includes
1x ES24TX Pro Micro TX module
1x Happymodel 2.4GHz Moxon antenna
This Slim Pro TX module is designed by Happymodel and based on the open-source ExpressLRS which is a very popular low latency and high packet rate RF module for RC Airplane and FPV Racing drones. Its main hardware architecture is ESP32, ESP8285, and SX1280 RF chip. The ES24TX Slim Pro module is a complete solution which is already pre-load the Expresslrs firmware and its plug-and-play for Frsky X-lite/X-lite pro/X9 Lite, TBS Tango2.This Slim Pro module comes with an aluminum alloy shell and is equipped with a cooling fan that automatically works when the module is working at 250mw.The slim pro-TX module supports a maximum power output of about 1000mw, this would be very useful for Long Range FPV.
Check out our other ELRS accessorieses, as well as the rest of our HappyModel selection.
Features
Supports up to 1000mw RF power (T-lite radio and Tango2 radio need external power supply)
RGB LED ready
Cooling Fan ready
Open source ExpressLRS
Long-range, low latency, and High re-flashed Rates
Telemetry data transmission supported
CNC aluminum protective shell
Specifications
Regulatory Domain: ISM2400
MCU: ESP32(main),ESP8285(as ESP backpack)
RF chip: SX1280IMLTRT
Frsky Lite 8pin socket
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
RF Output Power: ≤30dBm
Power supply voltage: 5v~12v
Weight: 50gram (without antenna）
Dimension: 67.5x30x20.5mm (without antenna)
Antenna gain: 1.87dBi
Antenna Connector: SMA
Includes
1x HappyModel ES24TX Slim Pro 2.4GHz RC Transmitter Module
1x Antenna
Recently the ExpressLRS system has become one of the most popular receiver systems on the market. This receiver will let you connect to any Express LRS module.
Check out our other receivers, as well As the rest of our Happymodel selection!
Specifications
RF Frequency: optional 915mhz or 868mHz (EU)
Weight: 0.60 gram Without Antenna
Telemetry Output Power: <17dBm
Operation Current: ~100Ma
Antenna Connector: IPEX1
Rx To FC Protocol: CRSF
Dimensions: 12x12x3mm
Input Voltage: 5V
Includes
1x Happymodel ES900RX Receiver for ExpressLRS
Recently the ExpressLRS system has become one of the most popular receiver systems on the market. This kit from Happymodel is a great combo to start with, it comes with both the receiver and module together. Before you know it, you'll be pushing the limits of what you thought was possible.
Check out our other transmitter modules, as well As the rest of our Happymodel selection!
Features
Compatible with OpenTX remote controllers, including the Radiomaster TX16S and Jumper T12, T16, and T18.
The 900TX module comes with a 2006 fan which allows it to work automatically when the TX power is at 250mW
ExpressLRS open-source software.
Ultra Long Range
Low Latency
Specifications
ES900RX
RF Frequency: optional 915mhz or 686mHz (EU)
Weight: 0.60 gram (excluding antenna)
Telemetry output Power: <17dBm
Operation current: ~100Ma
Antenna connector: IPEX1
Rx To FC protocol: CRSF
Dimension: 12x12x3mm
Input Voltage: 5V
ES900TX
Maximum Output Power: <33dBm (For >27dBm operation, we recommend adding a fan for force cooling)
RF Frequency optional: 915mhz or 868mHz (EU)
Dimension: 55x39x13mm
Input Voltage: 5~13V
Weight: 23g Without Antenna
Antenna Connector: SMA
MCU: ESP32+ESP8285
Includes
1x Happy Model ES900TX & ES900RX Combo for ExpressLRS
Great motor for any whoop and a perfect replacement part for the Happymodel Mobula 6 HD.
We also carry these motors in multiple KV options.
Check out the rest of our Mobula 6 parts & accessories and all our Happymodel gear!
Features
The lightest 0802 brushless motors around the world only 1.7g
Double E-clip design, prevent Motor bell to flying off
Good Dynamic balance
Specifications
KV: 19000Kv
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Terminals: JST1.25mm
No.of Cells(Lipo): 1S LiPo
Wire length(include connector): 27mm
Weight: 1.7g
Includes
1x Happymodel EX0802 19000Kv Whoop/Micro Motor for Mobula 6 HD - CW
Great motor for any whoop and a perfect replacement part for the Happymodel Mobula 6 HD.
We also carry these motors in multiple KV options.
Check out the rest of our Mobula 6 parts & accessories and all our Happymodel gear!
Features
The lightest 0802 brushless motors around the world only 1.7g
Double E-clip design, prevent Motor bell to flying off
Good Dynamic balance
Specifications
KV: 25000KV
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Terminals: JST1.25mm
No.of Cells(Lipo): 1S LiPo
Wire length(include connector): 27mm
Weight: 1.7g
Includes
1x Happymodel EX0802 25000Kv Whoop/Micro Motor for Mobula 6 HD - CW
The Happymodel EX1002 is a 1002 brushless motor with 20000KV. This is a replacement motor for the Happymodel 1S HDZero Whoop.
Check out the rest of our Mobula 6 parts & accessories and all our Happymodel gear!
Specifications
Input Voltage: 1S
Kv: 20000Kv
Shaft Diameter: 1.5mm
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Motor Dimension: Φ10.5x13.5mm
Wire length(include connector): 30mm
Weight: 2g
Includes
1x HappyModel EX1002 20000Kv Brushless Motor
The Happymodel SE0702 11000KV are the direct replacement motors for the Bassline 2S, so RDQ has you covered! It will also work great one any 2" Toothpick style drone.
Check out our other micro motors, and all our HappyModel selection!
Specifications
Kv: 11000Kv
Input Voltage: 1SS LiPo
Configuration: 9N12P
Motor Dimensions: Φ13.5mm x 15.5mm
Stator Dimensions: Φ11mm x 3mm
Shaft Diameter: Φ1.5mm
Mounting Pattern: Φ7mm
Weight: 3.8g
Includes
1x HappyModel EX1103 11000Kv Micro Motor
4x Motor Screws
Note: this motor is sold by HappyModel as a mix of CW & CCW options. These should be interchangeable, but if for some reason the rotation of the motor is not going the direction you desire, then you can simply reverse the settings in BLHeli or swap any two motor wires to reverse the direction.
