BSI102, Bob Smith Industries INSTA-CURE Super Thin CA (1oz)
This is a one ounce bottle of Bob Smith Industries Super Thin INSTA-CURE™ CA Glue. INSTA-CURE™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.
This product was added to our catalog on April 8, 2021
BSI107, Bob Smith Industries INSTA-CURE+ Gap Filling CA (1oz)
This is a one ounce bottle of Bob Smith Industries INSTA-CURE+™ Gap Filling CA Glue. INSTA-CURE+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ ™ should also be used. To prevent premature curing, don’t spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
This product was added to our catalog on April 8, 2021
TAM87182, Tamiya Extra-Thin Quick-Setting Cement (40ml)
The Tamiya Extra-Thin Quick-Setting Cement is a great time saver for the hobby enthusiast. This thin cement dries around 4 times faster than the Tamiya Extra-Thin Cement and is perfect for small parts. Being a thin formula it is able to flow into small seams or cracks and will set very quickly.NOTE: Not recommended for larger gaps or for use with elastomer (used on tank tracks) as it can cause brittleness.
This product was added to our catalog on March 2, 2021
BSI151, Bob Smith Industries INSTA-SET Foam Safe Accelerator Pump Spray (2oz)
This is a two fluid ounce Pump Spray bottle of Bob Smith Industries INSTA-SET™ Foam Safe CA Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together.
Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators.
It is compatible with all surfaces, even clear plastic and white foam.
This product was added to our catalog on April 8, 2021
BSI112, Bob Smith Industries MAXI-CURE Extra Thick CA (1oz)
This is a one ounce bottle of Bob Smith Industries MAXI-CURE™ extra thick CA glue. MAXI-CURE™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.MAXI-CURE™ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside of a cloth textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE™ or any other adhesive. It also is best for bonding the tires for R/C cars.
This product was added to our catalog on April 8, 2021
BSI103, Bob Smith Industries INSTA-CURE Super Thin CA (2oz)
This is a 2oz bottle of Bob Smith Industries Insta-Cure Super Thin CA Glue.
This product was added to our catalog on April 8, 2021
BSI127, Bob Smith Industries SUPER-GOLD+ Gap-Filling Odorless Foam Safe (1oz)
This is a one ounce bottle of Bob Smith Industries SUPER-GOLD+™ Gap Filling, Odorless, Foam Safe CA Glue. SUPER-GOLD™ and SUPER-GOLD+™ are BSI's odorless INSTA-CURE CAs. They are non-frosting and take only 2 or 3 seconds longer to bond.
There are no fumes that irritate the nose and eyes. The SUPER-GOLD™’s do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARF’s. They will not fog clear plastic. SUPER-GOLD+™ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE™ is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD +™ in less than fifteen seconds.
For bonding foam to foam, spray a very light fog of INSTA-SET™ to one piece and apply SUPER-GOLD+™ to the other before joining. Excess INSTA-SET™ may create too much heat, which can melt the foam. Both SUPER-GOLD™’s cure to a more flexible consistency for better shock absorption. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD™ eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.
This product was added to our catalog on April 8, 2021
BSI120, Bob Smith Industries INSTA-FLEX+ Clear Rubber Toughened CA (1oz)
This is a one ounce bottle of Bob Smith Industries INSTA-FLEX+™ Clear Rubber Toughened CA Glue. INSTA-FLEX+™ clear rubber toughened has similar qualities to our black IC-2000™ but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000™ that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX+™ has this carbon removed, its strength is a little less than IC-2000™ but still superior to standard CA's. When esthetics are important and a flexible bond is required, INSTA-FLEX+™ is your best choice. It forms superior bonds to soft urethane and vinyl plastics. Both INSTA-FLEX™ and INSTA-FLEX+™ work well when bonding R/C car tires. When a joint has a larger than normal gap, flexible CA's provide superior shock resistant bonds.
This product was added to our catalog on April 8, 2021
BSI201, Bob Smith Industries QUICK-CURE 5 Minute Epoxy (4 1/2oz)
This is a four and a half ounce package of Bob Smith Industries QUIK-CURE™ 5 Minute Epoxy. QUIK-CURE™ 5 Minute epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURE™ is the only BSI epoxy on which you can apply polyester resins. It can be mixed with microballoons to form a quick setting putty. Items bonded with QUIK-CURE™ can be handled after 15 minutes. Full strength is reached in 1 hour.
This product was added to our catalog on April 8, 2021
BSI155, Bob Smith Industries INSTA-SET Foam Safe Accelerator Aerosol Spray (3.75oz)
This is a 3.75 ounce aerosol spray can of Bob Smith Industries INSTA-SET™ Foam Safe CA Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together.
Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators.
It is compatible with all surfaces, even clear plastic and white foam.
This product was added to our catalog on May 28, 2021
BSI158, Bob Smith Industries SUPER-FIX Filler Welding Powder (1oz)
The Bob Smith Industries Super-Fix Filler Welding Powder is part of a two-part adhesive system developed to fill gaps and voids. It is sandable and paintable and cures in 1-3 seconds. Super-Fix is great for repairs at home, on autos, boats, and motorhomes. The super-thin consistency is perfect for bonding Metal, Plastic, Wood, Ceramics, Rubber, Leather, Glass, Auto Bumpers, Fiberglass, and more. Package includes one one-ounce bottle of welding powder.
SUPER-FIX FILLER DIRECTIONS: Twist off cap. Apply Filler to gaps in joints or voids to be filled. Apply drops of Super-Fix adhesive to the Filler, which will harden instantly. Corners of joints can be strengthened by forming fillets with the Filler and applying Super-Fix adhesive to harden them.
NOTE: Requires Super Fix Adhesive (BSI-158H)
This product was added to our catalog on March 15, 2021
BSI119, Bob Smith Industries INSTA-FLEX Flexible Thin CA (1oz)
This is a one ounce bottle of Bob Smith Industries INSTA-FLEX™ Flexible Thin CA Glue. INSTA-FLEX™ flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX™ does not turn brittle and remains clear, even if accelerated with INSTA-SET™. It has superior shock resistance. Although not as thin in consistency as INSTA-CURE™, INSTA-FLEX™ still has good penetrating qualities and its application can be easier to control. For CA hinges, we recommend drilling a 1/16" hole in the center of the hinge slots to insure the complete saturation of the hinge when INSTA-FLEX™ is applied. INSTA-FLEX™ has a different, less irritating odor compared to regular CA's, but still can not be used on white foam. INSTA-FLEX™ has also proven to be superior when bonding anodized aluminum.
This product was added to our catalog on April 8, 2021
BSI203, Bob Smith Industries MID-CURE 15 Minute Epoxy (4 1/2oz)
This is a four and a half ounce package of Bob Smith Industries MID-CURE™ 15 Minute Epoxy. MID-CURE™ 15 Minute epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURE™ in most applications. MID-CURE™ is BSI's most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength.
This product was added to our catalog on April 8, 2021
BSI-118, IC-2000 Rubber-toughened CA, 1 oz. (28.4 g)
IC-2000™ is a rubber-toughened cyanoacrylate that forms superior shock resistant bonds on non-porous surfaces. The black colored CA has added flexibility for the bonding of metals, fiberglass, rubber, carbon-fiber and other advanced materials. For model use, IC-2000™ is ideal for the bonding of bulkheads, formers and servo rails to the inside of fiberglass hulls and fuselages. Setup time is 20-40 seconds, which can be accelerated with INSTA-SET™. When cured, IC-2000™ is pliable enough to be carved with a hobby knife. IC-2000™ is the best adhesive for R/C car tires.
IC-2000™ has found many uses in industrial applications, such as rubber to rubber bonding by Beechcraft, carbon composite bonding by Boeing, rubber door seals by Volkswagen, speaker and subwoofer assembly in the audio industry and many others that need the most durable, shock resistant fast bonding adhesive that is available.
BSI205, Bob Smith Industries SLOW-CURE 30 Minute Epoxy (4 1/2oz)
This is a four and a half ounce package of Bob Smith Industries SLOW-CURE™ 30 Minute Epoxy. SLOW-CURE™ 30 minute epoxy works best for forming reinforcing fillets on joints. It has the highest strength of all the BSI epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURE™ to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours.
This product was added to our catalog on April 8, 2021
