FUT01102237-3, Futaba R203GF S-FHSS 3-Channel 2.4GHz Receiver
The Futaba R203GF 3-Channel 2.4GHz S-FHSS Receiver is compatible with Futaba FHSS and S-FHSS transmitters. Futaba S-FHSS 2.4GHz receivers benefit from Futaba's patented Pre-Vision™ circuitry, which scans incoming data and corrects errors before they can become problems. They sync perfectly with Continuous Channel Shifting, handling hundreds of frequency changes per second with flawless precision. Plus, they all offer the Easy-Link™ advantage — the feature that allows the receiver to “learn” the transmitter module’s unique code with the push of a button and establish a unique, unbreakable bond between the two.Frequency Hopping Spread Spectrum (FHSS) technology minimizes interference from other 2.4GHz systems. Easy Link prevents unwanted signal conflicts by using a special, pre-assigned ID code. High-voltage operation.NOTE: This receiver is NOT compatible with 2.4GHz FASST or FASSTest systems. It will work with FHSS and T-FHSS transmitters, but transmitter mode will need to be changed to from T-FHSS/FHSS to S-FHSS mode.Features:
S-FHSS/FHSS auto detection
Compatible with Futaba S-FHSS/FHSS protocol
Normal and high-speed mode:
Normal mode has a frame rate output of 13.63ms and accepts any type of servos or peripherals
High-speed mode, with an output of 6.8ms, accepts digital servos including the BLS series and most peripheral equipment such as brushless ESCs
Specifications:
Dimensions: 26x39x10mm (1x1.5x0.4")
Weight: 0.28oz (8g)
Operating Voltage: 4.8 to 7.4V |
Number of Ports: 4
PWM Output: 3
SBUS Ports: 0
SBUS2 Ports: 0
FASST: No
Telemetry: no
S-FHSS: Yes
High Speed: Yes
High Voltage: Yes
Connector: J (STND)
Range: Full Range
NOTE: This receiver is NOT compatible with 2.4GHz FASST, FASSTest or T-FHSS systems.
This product was added to our catalog on June 20, 2021
R304SB-E, Futaba R304SB-E T-FHSS 4-Channel Telemetry 2.4GHz Receiver (EP Only)
The Futaba R304SB-E T-FHSS 4-Channel Telemetry 2.4GHz Receiver is only compatible with Futaba T-FHSS telemetry compatible transmitters. The R304SB-E is very similar to the R304SB (FUTL7680) in that they both feature 4-channels, both feature S.Bus2, both are Telemetry enabled and both cost roughly the same price.
However, the two receivers differ in two fundamental areas: this R304SB-E is only intended for electric vehicles and features the benefit of having a non-exposed built-in antenna. The R304SB is compatible with electric/nitro/gas applications and the antenna is fully exposed.
NOTE:
The R304SB-E receiver is recommended for electric powered models only. This is NOT recommended for use with nitro or gas powered models.
Not compatible with the Futaba FHSS, S-FHSS, FASSTest or FASST transmitters.
Features:
T-FHSS System
Telemetry Enabled
4-Channels
Built-in Hidden Antenna
Electric Vehicle Use Only
Specifications:
Futaba System: T-FHSS
S.Bus2: Yes
Channels: 4
Range: 70m (230ft) (at best conditions)
Power Requirement Rated Voltage: 4.8-7.4V
Usable Voltage: 3.5-8.4V
Size: 1.38x0.91x0.33" (35.1x23.2x12.5mm)
Weight: 0.23oz (6.7g)
Number of Ports: 5
PWM Output: 4
SBUS Ports: 0
SBUS2 Ports: 1
FASST: No
Telemetry: Yes (T-FHSS)
S-FHSS: No
High Speed: Yes
High Voltage: Yes
Connector: J (STND)
Range: Only for Electric Powered Car Models
NOTE:
The R304SB-E receiver is recommended for electric powered models only. This is NOT compatible with nitro or gas powered models.
Not compatible with the Futaba S-FHSS, FHSS, FASSTest or FASST transmitters.
This product was added to our catalog on May 4, 2021
FUT01004347-3, Futaba 3PV 3-Channel 2.4GHz FHSS/S-FHSS Radio System w/R304SB Receiver
The Futaba 3PV Radio System is sophisticated, powerful and easy to use. Pick up the 3PV and instantly feel how lightweight it is. Once you access the programming menu on the easy-to-read screen, you will instantly recognize how sophisticated the programming is. But the real experience happens when you get to take advantage of the 3PV's super-fast response rate. This is a system that can make a difference on race day. You also get FHSS, S-FHSS and T-FHSS protocols, making it one of R/C's most versatile surface system.
This version of the 3PV with R304SB telemetry receiver (FUTK3200) is for those that want to keep an eye on their receiver voltage. But the 3PV is also available with a high-voltage R203GF receiver (FUTK3201) that is perfect for brushless ESCs and digital servos.
Features:
FHSS/S-FHSS/T-FHSS* protocols
10-model memory
Model Reset
Model Name (4-Character)
Low Battery Alarm
Link Mode (T-FHSS only)
DT3 Selection
SW1
Steering Trim
Throttle Trim
Channel 4 Trim
Sub Trim
Steering Dual Rates
Steering End Point Adjustment spacer
Throttle End Point Adjustment
Channel 3 End Point Adjustment
Channel 4 End Point Adjustment
4WS/Brake Mixing
Steering Servo Reversing
Throttle Servo Reversing
Channel 3 Servo Reversing
Channel 4 Servo Reversing
Steering Exponential
Throttle Exponential
Throttle Fail Safe
ABS Function
Model Data Copy
Auto Power-Off after 10 minutes
*NOTE: T-FHSS available only with R304SB receiver.
Specifications:
3PV Transmitter:
Type: 3-Channel FHSS/S-FHSS/T-FHSS*
Includes: 3-Channel R304SB Receiver
Requires: (4) "AA" alkaline batteries, or 6.6V 1900mAh LiFe battery (HCAM6521), or 6V NiMH Battery (FUTM1482)
R304SB Receiver:
Type: 3-Channel FHSS/S-FHSS/T-FHSS
Input Power: 4.8V-7.4V
Dimensions: 1.38 x 0.91 x 0.33 in (35.1 x 23.2 x 8.5 mm)
Weight: 0.23 oz (6.6 g)
This product was added to our catalog on July 14, 2021
R334SBS – Super Response T-FHSS Telemetry 4-Channel ReceiverHigh Speed Response System For Surface Models (01102246-3)
T-FHSS SRSIZE:33.9 mm x 22.3 mm x 11.3 mm1.33 in x 0.88 in x 0.44 in
WEIGHT:7.5 g0.26 oz
OPERATING VOLTAGE:DC 3.7V-7.4V
COMPATIBLE WITH THE T-FHSS/T-FHSS SYSTEM TRANSMITTERS.WHEN USING THE T-FHSS SR MODE, USE AN SR MODE SERVO. NORMAL SERVOS CANNOT BE USED.
THE USE OF NORMAL SERVOS MAY CAUSE SERVO TROUBLE.
FUT01004416-3, Futaba 4PM Plus 4-Channel 2.4GHz T-FHSS Radio System w/R304SB Receiver
The Futaba 4PM Plus 4-Channel 2.4GHz T-FHSS Radio System brings great advancements to the 4PM platform. This combo includes an R304SB receiver.
Features:
T-FHSS SR (SUPER RESPONSE) AND TELEMETRY T-FHSS: In addition to the T-FHSS telemetry system, we added a T-FHSS SR (Super Response) system that increased processing speed to further improve response. SR system does not support telemetry functions. *R304SB and R304SB-E are not compatible with SR system.
T-FHSS MINIZ SYSTEM: By changing to the MINIZ system in the receiver setting menu, you can use Kyosho Mini – Z Evo dedicated receiver RA-42. Dedicated receiver RA-42 requires purchase separately. 01004397-3 comes with no receiver.
FHSS MINIZ SYSTEM: By changing to the MI-FH system in the receiver setting menu, you can use Kyosho Mini – Z FH FS-RM005 module to connect to the non-Evo Mini-z.
TELEMETRY SYSTEM: The T4PM+ transmitter has adopted the newly developed bidirectional communication system “T-FHSS”.
2.4GHz SS RADIO COMMUNICATION SYSTEM: Frequency channel setting is unnecessary: Channel shifting takes place within the 2.4 GHz band automatically. This system minimizes interference from other 2.4 GHz systems.
MODEL MEMORY FOR 40 MODELS: Model names can use up to 10 letters, numbers, and symbols, so that logical names may be used. A model memory with different setups can be created using the model copy function.
4 AXIS JOG BUTTON: The (JOG) button can be operated in 4 directions: up, down, left, and right.
ESC-LINK FUNCTION (MC-LINK): This dedicated function allows you to set up the Link software so that your T4PM can control the variable frequency and other data changes in Futaba speed controllers (ESCs): MC970CR, MC850C, MC851C, MC602C, MC402CR, etc.
S.BUS SERVO: This is a special function that allows the setting of the parameters of our S.Bus servo whose settings are changed by using PC Link software. In addition to the conventional wired system, it can be set wirelessly in combination with the R334SBS or R334SBS-E.
STEERING MIXING: Smooth cornering is possible by the independent left and right steering servo settings.
BRAKE MIXING FOR LARGE CARS (BRAKE): Brake mixing of the front and rear wheels of 1/5 gas power cars and other large cars can be adjusted independently.
GYRO MIXING (GYRO MIX): The sensitivity of Futaba car rate gyros can be adjusted from the T4PM.
4WS MIXING FOR CRAWLERS AND OTHER 4WS TYPE (4WS): This function can be used with crawlers and other 4WS-type vehicles.
DUAL ESCS MIXING FOR CRAWLERS CARS (DUAL ESC): ESCs at the front and rear are controlled independently.
CPS-1 MIXING (CPS MIX): LED lighting and flashing control using our CPS-1 channel power switch can only be matched to steering and throttle operation by a switch.
ANTI-SKID BRAKING SYSTEM (TH A.B.S): This function applies the brakes so that the tires of gas-powered cars do not lose their grip on the road even when braking at corners.
THROTTLE ACCELERATION (ACCEL): Gas power cars have a time lag before the clutch and brakes become effective. The throttle acceleration function reduces this time lag.
THROTTLE SPEED (SPEED): Sudden trigger operation on a slippery road surface will only cause the tires to spin and the model to not accelerate smoothly. By setting the throttle speed function, the operation can be performed smoothly and easily. It also suppresses battery consumption.
STEERING SPEED (SPEED): When you sense that the steering servo is too fast, etc., the servo operating speed (direction that suppresses the maximum speed) can be adjusted.
RACING TIMER (TIMER): The lap timer can record 100 lap times and total time. The timer can also be started automatically by trigger operation. The race time and audible alarm can be set. Re-/fueling times are indicated by an audible alarm. An up timer is also provided.
FUNCTION SELECT SWITCH (SWITCH)/DIAL FUNCTION (TRIM DIAL): This assigns functions to 2 switches and dials (digital trim, digital dial). The step amount and operating direction can also be adjusted. Trim positioning at each model call is unnecessary because all the dials are digital.
TRIGGER POSITION CAN BE CHANGED: The position of the throttle trigger can be moved forward and backward.
TENSION ADJUSTMENT FUNCTION: The tension of the steering wheel and throttle trigger springs can be adjusted from the outside.
MECHANICAL ATL ADJUSTMENT: Make this adjustment when you want to decrease the total travel of the brake (push) side of the throttle trigger.
Specifications:
Transmitter:
Voltage: 4.5-6.6V
Communication Method: Bidirectional protocol
Maximum Range: 100m (Except the MINIT system) (Optimum condition)
Frequency: 2.4GHz
RF Power Output: 100mW EIRP
Current Drain: 150 mA or less
Transmission Antenna: 1/2(Lambda) di-pole
Receiver:
Dimensions: 35.1x23.2x8.5mm
Voltage: 4.0-8.4V
Weight: 6.6g
Includes:
(1) Futaba 4PM+ Transmitter
(1) Dry Battery Holder
(1) R304SB receiver
(1) Mini Screwdriver
Needed to Complete:
(3) AA Batteries or (1) 6.6V LiFe Battery
This product was added to our catalog on November 25, 2022
R334SBS-E,Futaba T-FHSS SR S.Bus2 4-Channel 2.4GHz Receiver (Electric Models Only)
Futaba R334SBS-E T-FHSS SR S.Bus2 4-Channel 2.4GHz Receiver. This receiver is recommended for electric models only.
NOTE:
This receiver is not compatible with gas powered models. Gas powered models should use the R334SBS receiver (FUTL7688).
SR mode servos must be used when using T-FHSS SR mode. Use of normal servos may cause servo trouble.
Not compatible with the Futaba FHSS, S-FHSS, FASSTest or FASST transmitters.
Features:
Surface 4ch 2.4GHz T-FHSS SR Diversity
2.4GHz T-FHSS S.BUS2
Frequency 2.4GHz
Surface Use
4 Channel
Specifications:
Input voltage: 4.8-7.4V
Weight: 7.2g
Dimensions: 33.9×22.3×11.3mm (3 × 2.5 × 1.5 in)
This product was added to our catalog on May17, 2023
FUT01004353-3, Futaba 3PV 3-Channel 2.4GHz FHSS/S-FHSS Radio System w/R203GF Receiver
The Futaba 3PV Radio System is sophisticated, powerful and easy to use. Pick up the 3PV and instantly feel how lightweight it is. Once you access the programming menu on the easy-to-read screen, you will instantly recognize how sophisticated the programming is. But the real experience happens when you get to take advantage of the 3PV's super-fast response rate. This is a system that can make a difference on race day. You also get FHSS, S-FHSS and T-FHSS protocols, making it one of R/C's most versatile surface system.
This version of the 3PV with high-voltage R203GF receiver (FUTK3201) is perfect for brushless ESCs and digital servos. But the 3PV is also available with the R304SB telemetry receiver (FUTK3200) for those that want to keep an eye on their receiver voltage.
Features:
FHSS/S-FHSS/T-FHSS* protocols
10-model memory
Model Reset
Model Name (4-Character)
Low Battery Alarm
Link Mode (T-FHSS only)
DT3 Selection
SW1
Steering Trim
Throttle Trim
Channel 4 Trim
Sub Trim
Steering Dual Rates
Steering End Point Adjustment spacer
Throttle End Point Adjustment
Channel 3 End Point Adjustment
Channel 4 End Point Adjustment
4WS/Brake Mixing
Steering Servo Reversing
Throttle Servo Reversing
Channel 3 Servo Reversing
Channel 4 Servo Reversing
Steering Exponential
Throttle Exponential
Throttle Fail Safe
ABS Function
Model Data Copy
Auto Power-Off after 10 minutes
*NOTE: T-FHSS available only with R304SB receiver.Specifications:
3PV Transmitter:
Type: 3-Channel FHSS/S-FHSS/T-FHSS*
Includes: 3-Channel R203GF Receiver
Requires: (4) "AA" alkaline batteries, or 6.6V 1900mAh LiFe battery (HCAM6521), or 6V NiMH Battery (FUTM1482)
R203GF Receiver:
Type: 3-Channel FHSS/S-FHSS
Input Power: 4.8V-7.4V
Dimensions: 1.37 x 0.9 x 0.33 in (33 x 23 x 8.5 mm)
Weight: 0.21 oz (6 g)
This product was added to our catalog on July 14, 2021
TRA3039, Traxxas 4-Cell Battery Holder Assembly (Futaba Connector)
This is a replacement Traxxas 4-Cell Battery Holder Assembly. This assembly holds four "AA" batteries and features a Futaba Connector. This holder is used with the Jato, but can be used with other vehicles requiring a 4-cell "AA" holder with a Futaba connector.
This product was added to our catalog on October 29, 2021
FUTUBA0140, Futaba LiFe Transmitter Battery (4PX) (6.6V/1700mAh)
This is an optional Futaba LiFe Batter (FT2F1700B) Battery which is 2s (6.6V), and 1700mAh. Used for the Futaba 4PX Radio.
This product was added to our catalog on January 11, 2021
FUT01004361-3, Futaba 4YF 2.4GHz FHSS 4 Channel Radio System (Airplane) w/R2004GF Receiver
This is the Futaba 4YF 2.4GHz FHSS 4-Channel Airplane Radio System, with an included R2004GF 4-Channel Receiver. Futaba quality, FHSS technology and an economical price make the 4YF 2.4GHz FHSS radio an excellent choice for cost-conscious modelers wanting an interference-free spread spectrum system for sport flying. The 4YF has always been a great value, and now Futaba has enhanced it with cutting-edge 2.4GHz performance and security!
2.4GHz FHSS TechnologyFrequency-hopping 2.4GHz FHSS technology results in a radio system that's as cutting-edge as it is easy to use!
R2004GF ReceiverThe R2004GF receiver is compatible only with electronics created specifically for 2.4GHz FHSS systems.
Features:
Frequency Hopping Spread Spectrum (FHSS) eliminates signal interference and frequency pins
The included R2004GF receiver features a flexible coaxial antenna that can be easily positioned inside the model for optimum reception
Easy, convenient push-button transmitter/receiver linking, with no binding plugs
Power Down Mode - reduces RF power for 90 seconds, simplifying ground checks for interference
All-channel servo reversing for more installation options
Power and servo reversing switches located out of the way to prevent accidental changes
Battery meter with green and red LED for instant "go/no-go" status
4YF Transmitter Specifications:
Band: 2.4GHz
Operating System: 2-stick, 4-channel
Power Supply: 6V (4 "AA" batteries)
Current Drain: 90mA
R2004GF Receiver Specifications:
Band: 2.4GHz
Power Requirements: 4.8V or 6V (shared with servo)
Current Drain: 30mA (at no signal)
Size: 1.54x1.02x0.39 inches (39x26x10mm)
Weight: 0.49oz (14g)
This product was added to our catalog on October 17, 2023
FUT01004396-3, Futaba 7PXR 7-Channel 2.4GHz T-FHSS Telemetry Radio System w/R334SBS-E
The Futaba 7PXR 2.4GHz 7-Channel T-FHSS radio system is the redesigned apex radio for Futaba and features a number of upgrades over the original 7PX. The 7PXR was designed to be lightweight and easy to use with a significantly improved menu system. This 7-Channel telemetry capable T-FHSS radio system delivers features you won't find in another radio systems. The innovations start with the T-FHSS SR Super Response protocol, and continue with full telemetry capability, a back-lit 4.3" LCD touch screen and a updated R334SBS-E Diversity Receiver.
NOTE:
R334SBS-E receiver is recommended for electric models only and is not compatible with gas powered models. Gas powered models should use the R334SBS receiver (FUTL7688 - included with FUT01004395-3).
SR mode servos must be used when using T-FHSS SR mode. Use of normal servos may cause servo trouble.
Features:
T-FHSS Super Response transmission system (Frame Rate of 2.45 msec)
Compatible with T-FHSS, S-FHSS and FASST systems
4.3" color LCD touch screen display
Telemetry capable
40 memory slots to save the configurations of your models
5 mix programs
S.Bus servo programming system
7 channels with epa adjustment, sub-trim, brake mixing and ABS
4WS mixing
Brake mixing
Gyro mixing
Steering mixing
Memory with lap times
Adjustable steering wheel and gas trigger
Micro SD card slot
Voice messages
Headphone jack
Suitable for left-handed people
Specifications:
Transmitter:
Transmitting Frequencies: 2.4 GHz band/ -Transmitting RF power output: 100 mW EIRP
Protocols: T-FHSS SR/T-FHSS/S-FHSS/FASST-C2
Power Requirement: Ni-MH – NT5F1800B (6 V)/LiFe – FT2F1700BV2 (6.6 V)
Current Drain: 350 mA or less (When the T-FHSS, Vibration off, back lighting on)
Transmitting Antenna: 1/2 dipole
Display: 4.3 Inch Backlighted Color TFT Liquid Crystal Touch Panel (NOTE: When you turn on your 7PXR, bright dots may appear on your screen display. Your display contains an extremely large number of TFT and is manufactured using high-precision technology. Any bright dots that may appear on your display are intrinsic of the TFT manufacturing technology.)
Receiver:
Size: 33.9x22.3x11.3mm (1.33x0.88x0.44")
Weight: 7.2 g (0.25 oz)
Operating Voltage: DC 3.7V-7.4V
Application: Electric models only
Includes:
T7PXR Transmitter
R334SBS-E Receiver
Dry Battery Holder
Wheel Offset Adapter
Wheel Adapter 32deg
Large Diameter Steering Wheel (54mm)
Trigger Brake Lever (Narrow Type)
Miniature Screwdriver
Screen Protector
(3) Receiver Plugs
This product was added to our catalog on April 16, 2021
7PXR US Limited Edition Transmitter – Super Response Digital Proportional RC System
For Use with Surface Models (01004407-3) (01004406-3)
FEATURES
FULL COLOR TOUCH SCREEN LCD:T7PXR has an HVGA 4.3 inch, full-color, backlit LCD touch screen. The screen is transflective which enables both indoor and outdoor visibility.
T-FHSS SR (SUPER RESPONSE) AND TELEMETRY T-FHSS:In addition to the T-FHSS telemetry system, we added a T-FHSS SR (Super Response) system that increased processing speed to further improve response. (SR system does not support telemetry function.)
UPDATEABLE SOFTWARE:Software can be updated by microSD card. Model data can also be saved in a microSD card. In addition, telemetry log data can be saved.
MODEL MEMORY FOR 40 MODELS:Model names can use up to 15 letters, numbers, and symbols, so that logical names may be used. A model memory with different setups can be created by using the model copy function.
NFC COMMUNICATION:It is possible to update the T7PXR itself in the future by NFC communication.
INTEGRAL TYPE DIAL SWITCH:A switch with both dial (DL1) and pus switch (PS6) functions.
BRAKE MIXING FOR LARGE CARS:Brake mixing of the front and rear wheel of 1/5 gas power cars and other large cars can be adjusted independently.
STEERING MIXING:Smooth cornering is possible by independent left and right steering servo setting.
4WS MIXING FOR CRAWLERS AND OTHER 4WS TYPE:This function can be used with crawlers and other 4WS type vehicles.
DUAL ESCS MIXING FOR CRAWLERS CARS:ESCs at the front and rear are controlled independently.
GYRO MIXING:The sensitivity of Futaba car rate gyros can be adjusted from the T7PXR.
TANK MIXING:This function is intended for vehicles such as tanks.
CPS-1 MIXING:LED lighting and flashing control using our CPS-1 channel power switch can be matched to steering and throttle operation by switch only.
S.BUS SERVO:This is a special function that allows setting of the parameters of our S.Bus servo whose settings are changed by using PC Link software.
MC-LINK:This dedicated function allows you set up the Link software so that your T7PXR can control variable frequency and other data changes in Futaba speed controllers (ESCs): MC960CR, MC950CR, MC850C, MC851C, MC602C, MC402CR, etc.
THROTTLE SPEED:Sudden trigger operation on a slippery road surface will only cause the tires to spin and the model to not accelerate smoothly. By setting the throttle speed function, operation can be performed smoothly and easily. It also suppresses battery consumption.
STEERING SPEED :When you sense that the steering servo is too fast, etc., the servo operating speed (direction that suppresses the maximum speed) can be adjusted.
NON-TELEMETRY LED:When the telemetry function is OFF to confirm that the telemetry function is not operating.
DIAL SELECT FUNCTION:This function assigns functions to dials (digital trim, drip dial, knob). The step amount and operating direction can also be adjusted. Trim positioning at each model call is unnecessary because all the dials are digital.
SWITCH SELECT FUNCTION:This function assigns functions to 5 switches. The operating directions can also be set.
WHEEL AND TRIGGER POSITION CAN BE CHANGED:The wheel position can be offset by using an accessory APA wheel position offset adapter. The wheel angle can also be adjusted. The position of the throttle trigger can be moved forward and backward.
TRIGGER BRAKE LEVER REPLACEMENT:The trigger brake lever is selected from a narrow nylon type and wide type.
TRIM/DIAL LOCK FUNCTIONS:Lock functions which prohibit setting and operating by transmitter trim, and dials are provided.
LEFT-HANDED SUPPORT:The left and right installation direction of the wheel section can be reversed.
VIBRATOR BUILT INTO THE GRIP:The vibrator can be operated at racing timer lap navigation, time-up, and low battery, telemetry alarm. It sets it on each function screen.
CONTENTS
YOUR T7PXR INCLUDES THE FOLLOWING COMPONENTS:
-T7PXR Transmitter
-R334SBS OR R334SBS-E Receiver
-Dry Battery Holder
-Wheel Offset Adapter
-Wheel Adapter 32deg
-Large Diameter Steering Wheel (54 mm)
-Trigger Brake Lever (Narrow Type)
-Miniature Screwdriver
-Screen Protector
-3 x Receiver Plugs
TRANSMITTER SPECS
WHEEL SYSTEM, 7 CHANNELS (S-FHSS SYSTEM), 4 CHANNELS WITH TFHSS-SR, T-FHSS, FASST SYSTEM
TRANSMITTING FREQUENCIES:2.4 GHz band/ -Transmitting RF power output: 100 mW EIRP
PROTOCOLS:T-FHSS SR/T-FHSS/S-FHSS/FASST-C2
POWER REQUIREMENT:Ni-MH – NT5F1800B (6 V)LiFe – FT2F1700BV2 (6.6 V)
CURRENT DRAIN:350 mA or less (When the T-FHSS, Vibration off, back lighting on)
TRANSMITTING ANTENNA:1/2λ dipole
4.3 INCH BACKLIGHTED COLOR TFT LIQUID CRYSTAL TOUCH PANEL**When you turn on your 7PXR, bright dots may appear on your screen display. Your display contains an extremely large number of TFT and is manufactured using high-precision technology. Any bright dots that may appear on your display are intrinsic of the TFT manufacturing technology.
RECEIVER SPECS
R334SBS
T-FHSS SR
SIZE:33.9 mm x 22.3 mm x 11.3 mm1.33 in x 0.88 in x 0.44 in
WEIGHT:7.5 g0.26 oz
OPERATING VOLTAGE:DC 3.7V-7.4V
R334SBS-E
T-FHSS SR
SIZE:33.9 mm x 22.3 mm x 11.3 mm1.33 in x 0.88 in x 0.44 in
WEIGHT:7.2 g0.25 oz
OPERATING VOLTAGE:DC 3.7V-7.4V
HPS-CT700– S.Bus2 High-Voltage Low-Profile Surface Servo
High Performance Servo with Brushless Motor (01102321-3)
FEATURES:– Suitable for RC cars 1/10 scale on/off road and drifting.– Programmable/HV Brushless Servo.– Custom New high power Brushless Motor.– Supports SR mode with T7PX.– Programmable and compatible with S.Bus and S.Bus2 systems.– Can be connected to a PC using the CIU-2/-3 USB adapter sold separately.– Upper/middle/bottom: Aluminum Case
Speed：0.07sec/60°(7.4V) ／ 0.08sec/60°(6.0V)
Torque：30.0kgf・cm(7.4V) ／ 23.0kgf・cm(6.0V)
Dimensions/Weight：40.5×21.0×26.2mm/54g
RATED VOLTAGE:DC 6.0V-7.4V
OPERATING VOLTAGE:DC 4.8-8.4V
ONLY FOR RC CARS SMALLER THAN 1/5 SCALE
7PXR Transmitter – Super Response Digital Proportional RC System
For Use with Surface Models (01004395-3) (01004396-3)
FEATURES
FULL COLOR TOUCH SCREEN LCD:T7PXR has an HVGA 4.3 inch, full-color, backlit LCD touch screen. The screen is transflective which enables both indoor and outdoor visibility.
T-FHSS SR (SUPER RESPONSE) AND TELEMETRY T-FHSS:In addition to the T-FHSS telemetry system, we added a T-FHSS SR (Super Response) system that increased processing speed to further improve response. (SR system does not support telemetry function.)
UPDATEABLE SOFTWARE:Software can be updated by microSD card. Model data can also be saved in a microSD card. In addition, telemetry log data can be saved.
MODEL MEMORY FOR 40 MODELS:Model names can use up to 15 letters, numbers, and symbols, so that logical names may be used. A model memory with different setups can be created by using the model copy function.
NFC COMMUNICATION:It is possible to update the T7PXR itself in the future by NFC communication.
INTEGRAL TYPE DIAL SWITCH:A switch with both dial (DL1) and pus switch (PS6) functions.
BRAKE MIXING FOR LARGE CARS:Brake mixing of the front and rear wheel of 1/5 gas power cars and other large cars can be adjusted independently.
STEERING MIXING:Smooth cornering is possible by independent left and right steering servo setting.
4WS MIXING FOR CRAWLERS AND OTHER 4WS TYPE:This function can be used with crawlers and other 4WS type vehicles.
DUAL ESCS MIXING FOR CRAWLERS CARS:ESCs at the front and rear are controlled independently.
GYRO MIXING:The sensitivity of Futaba car rate gyros can be adjusted from the T7PXR.
TANK MIXING:This function is intended for vehicles such as tanks.
CPS-1 MIXING:LED lighting and flashing control using our CPS-1 channel power switch can be matched to steering and throttle operation by switch only.
S.BUS SERVO:This is a special function that allows setting of the parameters of our S.Bus servo whose settings are changed by using PC Link software.
MC-LINK:This dedicated function allows you set up the Link software so that your T7PXR can control variable frequency and other data changes in Futaba speed controllers (ESCs): MC960CR, MC950CR, MC850C, MC851C, MC602C, MC402CR, etc.
THROTTLE SPEED:Sudden trigger operation on a slippery road surface will only cause the tires to spin and the model to not accelerate smoothly. By setting the throttle speed function, operation can be performed smoothly and easily. It also suppresses battery consumption.
STEERING SPEED :When you sense that the steering servo is too fast, etc., the servo operating speed (direction that suppresses the maximum speed) can be adjusted.
NON-TELEMETRY LED:When the telemetry function is OFF to confirm that the telemetry function is not operating.
DIAL SELECT FUNCTION:This function assigns functions to dials (digital trim, drip dial, knob). The step amount and operating direction can also be adjusted. Trim positioning at each model call is unnecessary because all the dials are digital.
SWITCH SELECT FUNCTION:This function assigns functions to 5 switches. The operating directions can also be set.
WHEEL AND TRIGGER POSITION CAN BE CHANGED:The wheel position can be offset by using an accessory APA wheel position offset adapter. The wheel angle can also be adjusted. The position of the throttle trigger can be moved forward and backward.
TRIGGER BRAKE LEVER REPLACEMENT:The trigger brake lever is selected from a narrow nylon type and wide type.
TRIM/DIAL LOCK FUNCTIONS:Lock functions which prohibit setting and operating by transmitter trim, and dials are provided.
LEFT-HANDED SUPPORT:The left and right installation direction of the wheel section can be reversed.
VIBRATOR BUILT INTO THE GRIP:The vibrator can be operated at racing timer lap navigation, time-up, and low battery, telemetry alarm. It sets it on each function screen.
CONTENTS
YOUR T7PXR INCLUDES THE FOLLOWING COMPONENTS:
-T7PXR Transmitter
-R334SBS OR R334SBS-E Receiver
-Dry Battery Holder
-Wheel Offset Adapter
-Wheel Adapter 32deg
-Large Diameter Steering Wheel (54 mm)
-Trigger Brake Lever (Narrow Type)
-Miniature Screwdriver
-Screen Protector
-3 x Receiver Plugs
TRANSMITTER SPECS
WHEEL SYSTEM, 7 CHANNELS (S-FHSS SYSTEM), 4 CHANNELS WITH TFHSS-SR, T-FHSS, FASST SYSTEM
TRANSMITTING FREQUENCIES:2.4 GHz band/ -Transmitting RF power output: 100 mW EIRP
PROTOCOLS:T-FHSS SR/T-FHSS/S-FHSS/FASST-C2
POWER REQUIREMENT:Ni-MH – NT5F1800B (6 V)LiFe – FT2F1700BV2 (6.6 V)
CURRENT DRAIN:350 mA or less (When the T-FHSS, Vibration off, back lighting on)
TRANSMITTING ANTENNA:1/2λ dipole
4.3 INCH BACKLIGHTED COLOR TFT LIQUID CRYSTAL TOUCH PANEL**When you turn on your 7PXR, bright dots may appear on your screen display. Your display contains an extremely large number of TFT and is manufactured using high-precision technology. Any bright dots that may appear on your display are intrinsic of the TFT manufacturing technology.
RECEIVER SPECS
R334SBS
T-FHSS SR
SIZE:33.9 mm x 22.3 mm x 11.3 mm1.33 in x 0.88 in x 0.44 in
WEIGHT:7.5 g0.26 oz
OPERATING VOLTAGE:DC 3.7V-7.4V
R334SBS-E
T-FHSS SR
SIZE:33.9 mm x 22.3 mm x 11.3 mm1.33 in x 0.88 in x 0.44 in
WEIGHT:7.2 g0.25 oz
OPERATING VOLTAGE:DC 3.7V-7.4V
Futaba 4PM 4-Channel 2.4GHz T-FHSS Radio System w/R334SBS Receiver
Futaba R334SBS TFHSS SR S.Bus2 HV 4-Channel 2.4GHz Receiver
DESCRIPTION
4PM Transmitter – Super Response Digital Proportional RC System
For Use with Surface Models (01004387-3) (01004388-3) (01004397-3)
FEATURES
T-FHSS SR (SUPER RESPONSE) AND TELEMETRY T-FHSS:In addition to the T-FHSS telemetry system, we added a T-FHSS SR (Super Response) system that increased processing speed to further improve response. SR system does not support telemetry function. *R304SB and R304SB-E are not compatible with SR system.
T-FHSS MINIZ SYSTEM:By changing to the MINIZ system in the receiver setting menu, you can use Kyosho Mini – Z Evo dedicated receiver RA-42. Dedicated receiver RA-42 requires purchase separately. 01004397-3 comes with no receiver.
TELEMETRY SYSTEM:The T4PM transmitter has adopted the newly developed bidirectional communication system “T-FHSS”.
2.4 GHZ SS RADIO COMMUNICATION SYSTEM:Frequency channel setting is unnecessary: Channel shifting takes place within the 2.4 GHz band automatically. This system minimizes the interference from other 2.4 GHz systems.
MODEL MEMORY FOR 40 MODELS:Model names can use up to 10 letters, numbers, and symbols, so that logical names may be used. A model memory with different setups can be created by using the model copy function.
4 AXIS JOG BUTTON:The (JOG) button can be operated in 4 directions: up, down, left, and right.
ESC-LINK FUNCTION (MC-LINK):This dedicated function allows you set up the Link software so that your T4PM can control variable frequency and other data changes in Futaba speed controllers (ESCs): MC950CR, MC850C, MC851C, MC602C, MC402CR, etc.
S.BUS SERVO:This is a special function that allows setting of the parameters of our S.Bus servo whose settings are changed by using PC Link software. In addition to the conventional wired system, it can be set wirelessly in combination with the R334SBS or R334SBS-E.
STEERING MIXING:Smooth cornering is possible by independent left and right steering servo setting.
BRAKE MIXING FOR LARGE CARS (BRAKE):Brake mixing of the front and rear wheel of 1/5 gas power cars and other large cars can be adjusted independently.
GYRO MIXING (GYRO MIX):The sensitivity of Futaba car rate gyros can be adjusted from the T4PM.
4WS MIXING FOR CRAWLERS AND OTHER 4WS TYPE (4WS):This function can be used with crawlers and other 4WS type vehicles.
DUAL ESCS MIXING FOR CRAWLERS CARS (DUAL ESC):ESCs at the front and rear are controlled independently.
CPS-1 MIXING (CPS MIX):LED lighting and flashing control using our CPS-1 channel power switch can be matched to steering and throttle operation by switch only.
ANTI-SKID BRAKING SYSTEM (TH A.B.S):This function applies the brakes so that the tires of gas powered cars, etc. do not lose their grip on the road even when braking at corners.
THROTTLE ACCELERATION (ACCEL):Gas power cars have a time lag before the clutch and brakes become effective. The throttle acceleration function reduces this time lag.
THROTTLE SPEED (SPEED):Sudden trigger operation on a slippery road surface will only cause the tires to spin and the model to not accelerate smoothly. By setting the throttle speed function, operation can be performed smoothly and easily. It also suppresses battery consumption.
STEERING SPEED (SPEED):When you sense that the steering servo is too fast, etc., the servo operating speed (direction that suppresses the maximum speed) can be adjusted.
RACING TIMER (TIMER):The lap timer can record 100 lap times and total time. The timer can also be started automatically by trigger operation. The race time and audible alarm can be set. Re-/fueling time are indicated by an audible alarm. An up timer is also provided.
FUNCTION SELECT SWITCH (SWITCH)/DIAL FUNCTION (TRIM DIAL):This assigns functions to 2 switches and dials (digital trim, digital dial). The step amount and operating direction can also be adjusted. Trim positioning at each model call is unnecessary because all the dials are digital.
TRIGGER POSITION CAN BE CHANGED:The position of the throttle trigger can be moved forward and backward.
TENSION ADJUSTMENT FUNCTION:The tension of the steering wheel and throttle trigger springs can be adjusted from the outside.
MECHANICAL ATL ADJUSTMENT:Make this adjustment when you want to decrease the total travel of the brake (push) side of the throttle trigger.
CONTENTS
YOUR T4PM INCLUDES THE FOLLOWING COMPONENTS:
-T4PM Transmitter
-R304SB OR R334SBS OR NO receiver
-Dry Battery Holder
-Mini Screwdriver
TRANSMITTER SPECS
T-FHSS SR/T-FHSS/S-FHSS SYSTEM, WHEEL TYPE, 4 CHANNELS
COMMUNICATION METHOD:One-way operating system
MAXIMUM OPERATING RANGE:100m (Except the MINIT system) (Optimum condition)
FOR SAFETY:F/S, B-F/S, ID
TRANSMITTER FREQUENCY:2.4 GHz band
RF POWER OUTPUT:100mW EIRP
POWER REQUIREMENT:(Dry Cell Battery) Penlight x 3 (4.5 V)
CURRENT DRAIN:150 mA or less
TRANSMISSION ANTENNA:1/2λ di-pole
RECEIVER SPECS
R304SB
T-FHSS
SIZE:35.1 mm x 23.2 mm x 8.5 mm
WEIGHT:6.6 g
OPERATING VOLTAGE:DC 4.8V-7.4V
R334SBS
T-FHSS SR
SIZE:33.9 mm x 22.3 mm x 11.3 mm1.33 in x 0.88 in x 0.44 in
WEIGHT:7.5 g0.26 oz
OPERATING VOLTAGE:DC 3.7V-7.4V
FUT01004409-1, Futaba 10PX 10-Channel 2.4GHz T-FHSS Radio System w/R404SBS-E Receiver
The Futaba 10PX 10-Channel 2.4GHz T-FHSS Radio System is a digital proportional RC system that features a super response rate. This transmitter features the F-4G telemetry with a faster response than the T-FHSS SR system. Made for the serious racer, this radio allows for many fine tuned adjustments including gyro mixing, throttle speed, steering speed, dual rate and more! These features and functions give you the needed adjustments for refined performance. This combo includes the Futaba R404SBS-E receiver for out of the box performance.
The large 4.3" is produced in full color and features a backlit LCD touch screen. The screen is transflective, allowing for excellent indoor and outdoor visibility. For extreme comfortability, the steering wheel may be angled and adjusted. This gives the user the ability to fine tune the fitment of the radio to best suite their driving style. For adaptability, the steering wheel may also be moved to a left-handed position. The switch layout offers precise control over the assigned channel/function.
NOTE: When the 10PX is powered on, bright dots may appear on the display. The display contains an extremely large number of Thin-Film-Transistors (TFT) and is manufactured using high-precision technology. Any bright dots that may appear on the display are intrinsic of the TFT manufacturing.
Features:
Full color touch screen LCD
F-4G system & telemetry
Up to 10 channels can be operated by using the S.BUS2 system
By setting to the MINIZ system in the receiver setting menu, you can use Kyosho Mini – Z Evo dedicated receiver RA-42 (Sold Separately)
Software can be updated via microSD card (Sold Separately)
40 model memory with allowance for 15 character names
Allows for the use of an optional LiPo
Brake mixing for large cars
Steering mixing is independent allowing for precise left and right steering servo settings
4WS mixing for crawlers
Dual ESCs mixing allows for two ESCs to be controlled independently
The sensitivity of Futaba car gyros can be adjusted from the T10PX
Tank mixing
CPS LED light mixing
Futaba S.BUS servo allows setting of the parameters of select Futaba S.BUS servo
Specifications:
Transmitter:
Frequencies: 2.4GHz band @ 100mW
Protocols: T-FHSS-SR/T-FHSS/S-FHSS/F-4G
Voltage:
LiPo: 7.4 V
LiFe: 6.6 V
Current Drain: 350 mA or less (When the T-FHSS, Vibration off, back lighting on)
Antenna: 1/2 dipole
R404SBS-E Receiver:
Size: 1.00×0.81×0.42in (25.5×20.7×10.6mm)
Weight: 7.2g (0.25oz)
Voltage: 3.7-7.4V DC
Includes:
(1) T10PX Transmitter
(1) R404SBS-E Receiver
(1) Dry Battery Holder
(2) Wheel offset adapters
(1) 32° Wheel adapter
(1) 5° Wheel Angle spacer
(1) Large diameter steering wheel
(2) Trigger guards
(1) Rubber Grip
(1) Hex wrench
(1) Short manual
This product was added to our catalog on April 6, 2022
FUT01004414-3, Futaba 4PM Plus 4-Channel 2.4GHz T-FHSS Radio System (No Receiver)
Features:
T-FHSS SR (SUPER RESPONSE) AND TELEMETRY T-FHSS: In addition to the T-FHSS telemetry system, we added a T-FHSS SR (Super Response) system that increased processing speed to further improve response. SR system does not support telemetry functions. *R304SB and R304SB-E are not compatible with SR system.
T-FHSS MINIZ SYSTEM: By changing to the MINIZ system in the receiver setting menu, you can use Kyosho Mini – Z Evo dedicated receiver RA-42. Dedicated receiver RA-42 requires purchase separately. 01004397-3 comes with no receiver.
FHSS MINIZ SYSTEM: By changing to the MI-FH system in the receiver setting menu, you can use Kyosho Mini – Z FH FS-RM005 module to connect to the non-Evo Mini-z.
TELEMETRY SYSTEM: The T4PM+ transmitter has adopted the newly developed bidirectional communication system “T-FHSS”.
2.4GHz SS RADIO COMMUNICATION SYSTEM: Frequency channel setting is unnecessary: Channel shifting takes place within the 2.4 GHz band automatically. This system minimizes interference from other 2.4 GHz systems.
MODEL MEMORY FOR 40 MODELS: Model names can use up to 10 letters, numbers, and symbols, so that logical names may be used. A model memory with different setups can be created using the model copy function.
4 AXIS JOG BUTTON: The (JOG) button can be operated in 4 directions: up, down, left, and right.
ESC-LINK FUNCTION (MC-LINK): This dedicated function allows you to set up the Link software so that your T4PM can control the variable frequency and other data changes in Futaba speed controllers (ESCs): MC970CR, MC850C, MC851C, MC602C, MC402CR, etc.
S.BUS SERVO: This is a special function that allows the setting of the parameters of our S.Bus servo whose settings are changed by using PC Link software. In addition to the conventional wired system, it can be set wirelessly in combination with the R334SBS or R334SBS-E.
STEERING MIXING: Smooth cornering is possible by the independent left and right steering servo settings.
BRAKE MIXING FOR LARGE CARS (BRAKE): Brake mixing of the front and rear wheels of 1/5 gas power cars and other large cars can be adjusted independently.
GYRO MIXING (GYRO MIX): The sensitivity of Futaba car rate gyros can be adjusted from the T4PM.
4WS MIXING FOR CRAWLERS AND OTHER 4WS TYPE (4WS): This function can be used with crawlers and other 4WS-type vehicles.
DUAL ESCS MIXING FOR CRAWLERS CARS (DUAL ESC): ESCs at the front and rear are controlled independently.
CPS-1 MIXING (CPS MIX): LED lighting and flashing control using our CPS-1 channel power switch can only be matched to steering and throttle operation by a switch.
ANTI-SKID BRAKING SYSTEM (TH A.B.S): This function applies the brakes so that the tires of gas-powered cars do not lose their grip on the road even when braking at corners.
THROTTLE ACCELERATION (ACCEL): Gas power cars have a time lag before the clutch and brakes become effective. The throttle acceleration function reduces this time lag.
THROTTLE SPEED (SPEED): Sudden trigger operation on a slippery road surface will only cause the tires to spin and the model to not accelerate smoothly. By setting the throttle speed function, the operation can be performed smoothly and easily. It also suppresses battery consumption.
STEERING SPEED (SPEED): When you sense that the steering servo is too fast, etc., the servo operating speed (direction that suppresses the maximum speed) can be adjusted.
RACING TIMER (TIMER): The lap timer can record 100 lap times and total time. The timer can also be started automatically by trigger operation. The race time and audible alarm can be set. Re-/fueling times are indicated by an audible alarm. An up timer is also provided.
FUNCTION SELECT SWITCH (SWITCH)/DIAL FUNCTION (TRIM DIAL): This assigns functions to 2 switches and dials (digital trim, digital dial). The step amount and operating direction can also be adjusted. Trim positioning at each model call is unnecessary because all the dials are digital.
TRIGGER POSITION CAN BE CHANGED: The position of the throttle trigger can be moved forward and backward.
TENSION ADJUSTMENT FUNCTION: The tension of the steering wheel and throttle trigger springs can be adjusted from the outside.
MECHANICAL ATL ADJUSTMENT: Make this adjustment when you want to decrease the total travel of the brake (push) side of the throttle trigger.
Specifications:
Voltage: 4.5-6.6V
Communication Method: Bidirectional protocol
Maximum Range: 100m (Except the MINIT system) (Optimum condition)
Frequency: 2.4GHz
RF Power Output: 100mW EIRP
Current Drain: 150 mA or less
Transmission Antenna: 1/2(Lambda) di-pole
Includes:
(1) Futaba 4PM+ Transmitter
(1) Dry Battery Holder
(1) Mini Screwdriver
Needed to Complete:
(3) AA Batteries or (1) 6.6V LiFe Battery
This product was added to our catalog on November 25, 2022
The Futaba Transmitter Carrying Box is an excellent choice to store and protect your radio investment. The exterior features a gloss black finish over a durable hardshell. A reinforced rubber handle allows for increased grip and rigidity. An interior retention strap keeps your transmitter locked in place during travel. To top off the protection, Futaba includes a soft neoprene bag to protect your transmitter from scratches.
Features:
Durable hardshell gloss black finish.
Rubber handle for increased grip and rigidity.
Sized to fit in any overhead airplane compartment.
Elastic retention straps for reduced movement of transmitter.
Additional soft neoprene bag for added protection from scratches.
Shoulder strap for hands off transport included.
Specifications:
Size 9x17x12in
This product was added to our catalog on September 6, 2023
01004432-3, Futaba 10PX USLE 10-Channel 2.4GHz T-FHSS Radio System w/Case (Limited Edition)
The Futaba 10PX USLE, featuring a limited edition serial number, 3D carbon handle, and a magnesium steering housing, stands as the ultimate remote control transmitter for precision and performance. At its core, you'll find an impressive full-color TFT Liquid Crystal Touch screen LCD, generously sized at 4.3 inches, making it ideal for both indoor and outdoor use. Thanks to its transflective technology, it guarantees crystal-clear visibility in any lighting condition.
In addition to its remarkable display, the Futaba 10PX offers exceptional functionality with its 10 channels, driven by the lightning-fast F-4G system, delivering unbeatable telemetry responsiveness. If you require even greater versatility, the S.BUS2 system enables the simultaneous operation of up to 10 channels. Moreover, you have the option to personalize your experience using the T-FHSS MINIZ system, providing you with the flexibility to fine-tune your setup through the Kyosho Mini-Z Evo dedicated receiver.
Besides these state-of-the-art attributes, the 10PX boasts a plethora of features, including brake and steering mixing for larger vehicles, 4WS mixing for crawlers, and gyro sensitivity adjustments. Its compatibility with LiPo batteries, ability to receive firmware updates via a microSD card, and customizable button configuration make it an empowering choice for taking command like never before. Elevate your RC experience with the 10PX – it's the ultimate tool for dedicated enthusiasts.
Features:
Full color TFT Liquid Crystal Touch
USLE Trim Level with magnesium steering bracket and Limited Edition serial number
Includes high-quality carrying case
F-4G system & telemetry
Up to 10 channels can be operated by using the S.BUS2 system
By setting to the MINIZ system in the receiver setting menu, you can use Kyosho Mini – Z Evo dedicated receiver RA-42 (Sold Separately)
Software can be updated via microSD card (Sold Separately)
40 model memory with allowance for 15 character names
Brake mixing for large cars
Steering mixing is independent allowing for precise left and right steering servo settings
4WS mixing for crawlers
Dual ESCs mixing allows for two ESCs to be controlled independently
The sensitivity of Futaba car gyros can be adjusted from the T10PX
Futaba S.BUS servo allows setting of the parameters of select Futaba S.BUS servo
CPS LED light mixing
Tank mixing
Compatible with 6.6V LiFe and 7.4V LiPo Batteries
Specifications:
Frequency: 2.4GHz @ 100mW
Protocols: T-FHSS-SR/T-FHSS/S-FHSS
Voltages: 6.6V LiFe/7.4V LiPo
Current Drain: 350mA or Less
Antenna Type: 1/2 Dipole
Display: 4.3in TFT Liquid Crystal Touch
Includes:
(1) 10PX USLE Transmitter with limited edition number plate
(1) Limited edition carrying case with badge
(1) 3D Carbon fiber handle
Magnesium steering housing
(3) Limited edition gray grips
(1) Dry Battery Holder
32° and 5° Wheel offset adapters
(1) Large and small diameter steering wheel
Multi tension spring kit
(2) Trigger guards
(1) Rubber Grip
(1) Hex wrench
(1) Short manual
This product was added to our catalog on November 25, 2023
FUT01102170-1, Futaba S9650 Servo Digital Mini
This is the Futaba S9650 Digital Mini Servo with two ball bearings for helicopter and airplane use and comes with "J" connector pre-installed. Precision fixed-wing and helicopter flying requires precise, high-tech servos, and we are answering the call with new digital servos that reach full power immediately. They feature high-capacity, high-current wire for low resistance while maintaining standard servo dimensions and light weight so you can mount them almost anywhere.
Specifications:
Speed: .14 sec/60 degrees @ 4.8V - .11 Sec/60 Degrees @ 6.0V
Torque: 50.0 oz-in @ 4.8V - 62.5 oz-in @ 6.0V
Weight: 0.9 oz (26grams)
Length: 1.4" (35.6mm)
Width: 0.6" (15.2mm)
Height: 1.1" (27.9mm)
This product was added to our catalog on May 3, 2023
FUT01004408-1, 10PXR404SBS, Futaba 10PX 10-Channel 2.4GHz T-FHSS Radio System w/R404SBS Receiver
Futaba 10PX 10-Channel Touch Screen Radio System
The Futaba 10PX 10-Channel 2.4GHz T-FHSS Radio System is a digital proportional RC system that features a super response rate. This transmitter features the F-4G telemetry with a faster response than the T-FHSS SR system. Made for the serious racer, this radio allows for many fine tuned adjustments including gyro mixing, throttle speed, steering speed, dual rate and more! These features and functions give you the needed adjustments for refined performance. This combo includes the Futaba R404SBS receiver for out of the box performance.
The large 4.3" is produced in full color and features a backlit LCD touch screen. The screen is transflective, allowing for excellent indoor and outdoor visibility. For extreme comfortability, the steering wheel may be angled and adjusted. This gives the user the ability to fine tune the fitment of the radio to best suite their driving style. For adaptability, the steering wheel may also be moved to a left-handed position. The switch layout offers precise control over the assigned channel/function.
NOTE: When the 10PX is powered on, bright dots may appear on the display. The display contains an extremely large number of Thin-Film-Transistors (TFT) and is manufactured using high-precision technology. Any bright dots that may appear on the display are intrinsic of the TFT manufacturing.
Features:
Full color touch screen LCD
F-4G system & telemetry
Up to 10 channels can be operated by using the S.BUS2 system
By setting to the MINIZ system in the receiver setting menu, you can use Kyosho Mini – Z Evo dedicated receiver RA-42 (Sold Separately)
Software can be updated via microSD card (Sold Separately)
40 model memory with allowance for 15 character names
Allows for the use of an optional LiPo
Brake mixing for large cars
Steering mixing is independent allowing for precise left and right steering servo settings
4WS mixing for crawlers
Dual ESCs mixing allows for two ESCs to be controlled independently
The sensitivity of Futaba car gyros can be adjusted from the T10PX
Tank mixing
CPS LED light mixing
Futaba S.BUS servo allows setting of the parameters of select Futaba S.BUS servo
Specifications:
Transmitter:
Frequencies: 2.4GHz band @ 100mW
Protocols: T-FHSS-SR/T-FHSS/S-FHSS/F-4G
Voltage:
LiPo: 7.4 V
LiFe: 6.6 V
Current Drain: 350 mA or less (When the T-FHSS, Vibration off, back lighting on)
Antenna: 1/2 dipole
R404SBS Receiver:
Size: 1.00×0.81×0.42in (25.5×20.7×10.6mm)
Weight: 5.7g (0.2oz)
Voltage: 3.7-7.4V DC
Includes:
(1) T10PX Transmitter
(1) R404SBS Receiver
(1) Dry Battery Holder
(2) Wheel offset adapters
(1) 32° Wheel adapter
(1) 5° Wheel Angle spacer
(1) Large diameter steering wheel
(2) Trigger guards
(1) Rubber Grip
(1) Hex wrench
(1) Short manual
This product was added to our catalog on June 19, 2022
01102289-1, Futaba, SBS-01V External Battery Voltage Sensor
This is the Futaba SBS-01RO Optical RPM Sensor. Getting the performance information you want has never been easier, lighter or more convenient! This sensor plugs into the S.Bus2 slot on telemetry-enabled receivers, and transmits the data directly to FASSTest systems.
Specifications:
Displays: revolutions per minute
Range: 360-300,000
Weight: 0.17 oz (4.9 g)
This product was added to our catalog on February 25, 2023
01102213-1, Futaba, SBS-01T Temperature Sensor
This is an optional Futaba SBS-01T Temperature Sensor. This sensor simply plugs into the S.Bus2 slot on telemetry-enabled receivers, which transmit data directly to FASSTest systems.
Monitor temperatures on engines, motors, mufflers and batteries - nearly anything that radiates heat!
Specifications:Range: -4 to 392° F (-20 to 200°C)Weight: 0.16 oz (4.6g)Size: 535mm
This product was added to our catalog on March 15, 2023
FUT01102212-1, Futaba SBS-01RO Optical RPM Sensor
This is the Futaba SBS-01RO Optical RPM Sensor. Getting the performance information you want has never been easier, lighter or more convenient! This sensor plugs into the S.Bus2 slot on telemetry-enabled receivers, and transmits the data directly to FASSTest systems.
Specifications:
Displays: revolutions per minute.
Range: 360-300,000
Weight: 0.17 oz (4.9 g)
This product was added to our catalog on February 25, 2022
CIU-3-USB Interface
For Communication Between Link-Supported Devices (01102291-1)
INTERFACE:USB Rev 2.0 Compliant
USB CONNECTOR:USB Series A Connector
DIMENSIONS:18.2 mm x 56.5 mm x 9.0 mm0.72 in x 2.22 in x 0.35 in
WEIGHT:7.5 g0.26 oz
OPERATING VOLTAGE:5.0 V ± 0.2 V (USB Bus Power)
OPERATING ENVIRONMENT:Temperature -10 ~ 45° C
CURRENT DRAIN (AT CONNECTION, IDLE):5.8 ± 1.7 mA
APPLICABLE OS:Windows 10 / 8 / 7 / Vista
A PC-LINK ADAPTER (DOUBLE EXTENSION CORD K500) IS SUPPLIED WITH CIU-3
R203GF (S-FHSS) 2.4 GHz System 3-Channel Receiver
For EP Car Models (01102202-3)
S-FHSS/FHSS (Auto Detection)
SIZE:39 mm x 26 mm x 10 mm1.54 in x 1.02 in x 0.39 in
WEIGHT:8 g0.28 oz
OPERATING VOLTAGE:DC 4.8V-7.4V
NOTE: FUTABA S-FHSS/FHSS SYSTEM DOES NOT WORK WITH CURRENT FUTABA FASST SYSTEM. FASST SYSTEM AND S-FHSS/FHSS SYSTEM ARE NOT COMPATIBLE WITH EACH OTHER.
