The Mobula6 Micro FPV Whoop features the Runcam Nano3, Onboard Frsky Receiver, 5A BLheli_S 4-in-1 ESC, and more! This mini and lightweight whoop (65mm) will take you hard-to-get places!
Pick a motor: Race (25000Kv) or Standard (19000Kv).
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Features
- AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
- Extreme light 1S 65mm Brushless whoop only 20g
- Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
- Smooth and powerful
- Compatible with 1S Lipo/LIHV
- Camera Angle adjustable
Specifications
- Brand Name: Happymodel
- Item Name: Mobula6 1S 65mm Brushless whoop drone BNF version
- Wheelbase: 65mm
- Size: 80mmx80mmx37mm
- Weight: 20g
- Receiver option:
- Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
- Motor speed option:
- SE0802 KV25000(Race Edition)
- SE0802 KV19000(Regular Edition)
Motors
- Model: SE0802 19000KV or KV25000
- Configuration:9N12P
- Stator Diameter:8mm
- Stator Length:2mm
- Shaft Diameter: Φ1mm
- Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
- Weight(g):1.9g
- No.of Cells(Lipo):1S only
Propellers
- Gemfan 1219-3
- Center Thickness:5mm
- Prop Disk Diameter:31mm
- Center Hole Inner diameter:1.0mm
- Weight:0.28g
Flight controller
- (Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
- MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
- Sensor: ICM42688P
- Board size: 28.5x28.5MM
- Power supply: 1S battery input (DC 2.9V-4.35V)
- Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
- Built-in Betaflight OSD(SPI Control)
- Built-in 5.8G VTX
- Built-in SPI Frsky/Flysky receiver
- Built-in 5V 1A BEC
- Built-in voltage detection
Onboard 4in1 ESC
- MCU upgraded to ICM42688P
- Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
- Support BLHeliSuite programmable
- Factory firmware: O_H_5_REV16_7.HEX
- Default protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version
- SPI BUS receiver Frsky D8 compatible
- Compatible Non-EU transmitter D8 modelChannels: 8ch
- Failsafe support
- No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Onboard 5.8g VTX
- Output power: 25mw
- Frequency: 40CH
- Input voltage: 3.3V 5.5V
- Current consumption: 300mA(type)
- Frequency: 5.8GHz 5bands 40 channels
- With Race bandSmartaudio ready
Runcam Nano3
- Model: RunCam Nano 3
- Image Sensor: 1/3″ CMOS
- Horizontal Resolution: 800TVL
- Lens : 2.1mm(M8) FOV 160°
- Signal System: NTSC
- S/N Ratio: >50dBElectronic Shutter Speed: Auto
- Auto Gain Control (AGC): Auto
- Min. Illumination: 0.01Lux@1.2F
- D-WDR: Auto
- Day/Night: Color
- Power: DC 3-5.5V
- Current: 110mA@5V 120mA@3.3V
- Housing Material: ABS
- Net Weight: 1.2g
- Dimensions: L14mmxW14mmxH9mm
Lipo Battery
- Capacity:300mAh
- Voltage:3.8v
- Continuous Discharge Rate: 30C
- Size: 57mmx12mmx7mm
- Weight: 8gConnector: PH2.0
Includes
- 1x Mobula6 1S 65mm whoop Drone Frame
- 1x SPI Receiver: Crazybee F4 Lite FC built-in Frsky SPI D8 RX
- 4x SE0802 KV19000 or KV25000 brushless motor
- 1x Gemfan 1219-3 Propellers(4cw+4ccw)
- 1x Runcam Nano3 1/3 CMOS 800TVL camera
- 1x 5.8G 25mw 40ch VTX (Flight controller built-in)
- 4x 1S 300mah 30C LiHV Battery
- 1x 1S Lipo/LIHV USB Charger
- 1x Propeller disassemble tool
