All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 3.8V 1S 660mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 660mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance.
Check out our other 1S packs and our selection of Gaoneng Products!
Specifications
Capacity: 660mAh
Voltage: 3.8V (LiHV)
Cells Configuration: 1S1P
Pack Dimension: 8x17.5x66mm (HxWxL)
Net Weight: 15g (+/-1g)
Discharge Rate: 90C
Charge Rate: 1C to 5C
Discharge and Charge Connector: A30
Includes
1x Gaoneng GNB 3.8V 1S 660mAh 90C LiHV Whoop/Micro Battery w/ Cabled - A30
All batteries must be shipped by a ground shipping method.
The "Yellow Label" 100C/200C lipo batteries from GNB is their new light weight line.
These packs have same great performance and quality that you would expect from GNB but feature a plastic protection plate instead of the conventional aluminum or fiber glass.
Check out our 1S battery selection and our selection of Gaoneng Products!
Specifications
Capacity: 660mAh
Continuous Discharge Rate: 90C
Dimensions: 7.8x18x5.8mm
Discharge Lead: 12mm
Weight: 15g (+/- 1%)
Includes
1x Gaoneng 3.8V 1S 660mAh 90C LiHV Whoop/Micro Battery w/ PH2.0
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 3.8V 1S 660mAh 90C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 660mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance.
Check out our other 1S packs and our selection of Gaoneng Products!
Specifications
Model No.: GNB6601S90AHV
Capacity: 660mAh
Voltage: 3.8V (LiHV)
Cells Configuration: 1S1P
Pack Dimension: 8x17.5x60mm (HxWxL)
Net Weight: 15.5g (+/-1g)
Discharge Rate: 90C
Charge Rate: 1C to 5C
Discharge and Charge Connector: A30
Includes
1x Gaoneng GNB 3.8V 1S 660mAh 90C LiHV Whoop/Micro Battery w/ Plastic Head - A30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 720mAh and a discharge rate of 100C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance.
Check out our other 1S packs and our selection of Gaoneng Products!
Specifications
Capacity: 720mAh
Voltage: 3.8V (LiHV)
Cells Configuration: 1S1P
Pack Dimension: 7.5x18x66mm (HxWL)
Net Weight: 18.5g (+/-1g)
Discharge Rate: 100C
Charge Rate: 1C to 5C
Discharge and Charge Connector: A30
Includes
1x Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Whoop/Micro Battery w/ Cabled - A30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 720mAh and a discharge rate of 100C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance.
Check out our other 1S packs and our selection of Gaoneng Products!
Specifications
Capacity: 720mAh
Voltage: 3.8V (LiHV)
Cells Configuration: 1S1P
Pack Dimension: 7.3x18x66mm (HxWxL)
Net Weight: 16.5g (+/-1g)
Discharge Rate: 100C
Charge Rate: 1C to 5C
Discharge and Charge Connector: PH2.0
Includes
1x Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Whoop/Micro Battery w/ Cabled - PH2.0
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 720mAh and a discharge rate of 100C, it provides reliable, efficient power with a long flight time. With an A30 connector, you can count on secure, reliable connections and minimal resistance.
Check out our other 1S packs and our selection of Gaoneng Products!
Specifications
Capacity: 720mAh
Voltage: 3.8V (LiHV)
Cells Configuration: 1S1P
Pack Dimension: 7.5x18x65mm (HxWxL)
Net Weight: 16g (+/-1g)
Discharge Rate: 100C
Charge Rate: 1C to 5C
Discharge and Charge Connector: A30
Includes
1x Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Whoop/Micro Battery w/ Plastic Head - A30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Battery is the perfect solution for your 1S quads. Boasting a capacity of 720mAh and a discharge rate of 100C, it provides reliable, efficient power with a long flight time. With a PH2.0 connector, you can count on secure, reliable connections and minimal resistance.
Check out our other 1S packs and our selection of Gaoneng Products!
Specifications
Capacity: 720mAh
Voltage: 3.8V (LiHV)
Cells Configuration: 1S1P
Pack Dimension: 7.3x18x65mm (HxWxL)
Net Weight: 16g (+/-1g)
Discharge Rate: 100C
Charge Rate: 1C to 5C
Discharge and Charge Connector: PH2.0
Includes
1x Gaoneng GNB 3.8V 1S 720mAh 100C LiHV Whoop/Micro Battery w/ Plastic Head - PH2.0
The A30 high current connectors are an ideal fit for high-performance drones, providing a reliable connection with minimal resistance. This 5-pack of A30 Pigtails has each measuring 80mm. Get improved performance and reliability with the ability of up to 15A of continuous current - far higher than the 4.5A of PH2.0 connectors. Discharging more current in the same capacity than PH2.0 crimped pins, A30 connectors provide significantly more power - leading to extended flight time at full throttle on 1S whoop drones. Upgrade to A30 connectors for better performance and reliability.
Check out all our pigtails and connectors as well as our selection of Gaoneng Products!
Specifications
Wire Length: 80mm
Wire Gauge: 20AWG
Weight: 1.2g (ea.)
Connector: A30 Female
Includes
These props are an exact replacement for the Flywoo 1s Nano quad but are perfect for any 40mm whoop. They provide an enhanced flight feel and a good punch for your little ripper.
Check out the rest of our micro props, and all our Gemfan selection!
Specifications
Diameter: 40mm
Pitch: 1"
Blades: 2
Material: Polycarbonate
Hub Thickness: 5mm
Shaft Hole: 1.5mm
Weight: 0.25g
Includes
8x Gemfan Bi-Blade 40mm Props For Flywoo 1S Nano - Clear Blue (1.5mm Shaft)
These props are an exact replacement for the Flywoo 1s Nano quad but are perfect for any 40mm whoop. They provide an enhanced flight feel and a good punch for your little ripper.
Check out the rest of our micro props, and all our Gemfan selection!
Specifications
Diameter: 40mm
Pitch: 1"
Blades: 2
Material: Polycarbonate
Hub Thickness: 5mm
Shaft Hole: 1mm
Weight: 0.25g
Includes
8x Gemfan Bi-Blade 40mm Props For Flywoo 1S Nano - Clear Gray (1mm Shaft)
GEPRC SPEEDX2 0802 brushless motor, specially developed for Micro and Whoop FPV, SPEEDX2 motors are enough to meet your needs. GEPRC SPEEDX2 0802 motors have good heat dissipation, lightweight design, and advanced material technology, perfect for Micro and Whoop applications.
Specifications
Check out all our motors and our GEPRC selection!
Specifications
Kv: 17000kv
Input Voltage: 1S
Configuration: 9N12P
Shaft Diameter: 1mm
Mounting Pattern: Φ6mm, 3x M1.4
Wire Dimensions: JST-1.25, 33.5mm
Weight: 2g (w/ wire)
Includes
1x GEPRC SPEEDX2 0802 Micro Motor
The GEPRC SPEEDX2 0803 brushless motor is specially developed for Micro and Whoop FPV. These SPEEDX2 motors are enough to meet your needs. The 0803 motors have good heat dissipation, lightweight design, and advanced material technology, perfect for Micro and Whoop FPV applications.
Specifications
Check out all our motors and our GEPRC selection!
Specifications
Kv: 11000
Input Voltage: 1S
Configuration: 9N12P
Shaft Diameter: 1mm
Mounting Pattern: Φ6mm, 3x M1.4
Wire Dimensions: JST-1.25, 33.5mm
Weight: 2.4g (w/ wire)
Includes
1x GEPRC SPEEDX2 0803 Micro Motor
A note from GNB: We define this connector's "gender" by plastic not by metal bullet. Female is used on the Drone side while Male is used on the Battery side. This is opposite of XT30 and XT60. Make Selection Carefully.
A genuine GNB27 connecter directly from GNB. Upgrade your whoop's performance dramatically with this simple upgrade.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Features
GNB27 connector can support 9A continuous current and 15A burst, while the PH2.0 connector supports ONLY 4.5A continuous current
Compared with the PH2.0 crimped pins, GNB27 connector is more durable which can discharge more currents in the same capacity and provide far more power. You can get more flight time in full throttle on 1S whoop
Includes
5x GNB27 Connectors
The world’s first AIO 5in1 F4 flight controller with an integrated SPI 2.4GHz ExpressLRS receiver has been launched. The flight controller integrates SPI controlled 2.4GHz ExpressLRS receiver, Dshot protocol 4-in-1 ESC, 5.8GHz 40ch video transmitter, and Betaflight OSD. Ultra-small size and ultra-stable remote control range can improve the range of the original SPI receiver. And because the 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency, this flight controller is what all Race/Freestyle pilots need. It is suitable for whoop Race or Toothpick Freestyle, and can also be used in the 1S ultra-lightweight Nano Long Range platform.
Check out our other whoop flight controllers, and the rest of our Happymodel offerings.
Specifications
HappyModel ELRS 2G4 Whoop Flight Controller
MCU: STM32F411CEU6
Gyro: ICM20689
Input Voltage: 1S (2.9-4.35V)
Firmware Target: CRAZYBEEF4SX1280
Onboard ESC
MCU: EFM8BB21Input Voltage: 1S (2.9-4.35V)
Current: 5A continuous peak 6A (3 seconds)
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT600
Onboard 2.4GHz ExpressLRS Receiver
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS. Could bind with Happymodel ES24TX, ES24TX Lite, ES24TX Slim, and DIY 2.4GHz ELRS TX module (need to flash the same version ELRS firmware)
Onboard 5.8HGz VTX
Output power: 25-200mw switchable
Frequency: 5.8GHz 5bands 40 channels(include Race band) Smart audio ready
Current consumption: 300mA
Includes
1x HappyModel 1S F4 AIO Toothpick/Whoop Flight Controller w/ 5A 8bit 4in1 ESC & 200mW VTX - ELRS 2.4GHz SPI
1x Connecting Wire
1x Dipole Antenna
4x Damping Balls
1x 3-Pin Wire
5x Screws
Downloads
Firmware
The Happymodel 1S Balance Charging Board allows you to charge up to four 1S LiPo batteries with PH2 connector at the same time.
The board supports a maximum 1.5A charging current but charge at 1C to be safe. This method of charging is a little safer then parallel charging as it allows the charger to individually monitor and balance each cell.
This is a great charger for anyone that would like to charge 1s liPos for your Mobula, Moblite or Mobeetle!
Check out our other charging accessories, as well as the rest of our HappyModel gear!!
Specifications
Input Voltage: 1S
Max Amperage: 1.5A
Dimensions: 81x46x20mm
Weight: 35g
Includes
1x HappyModel 1S Series LiPo Balance Charging Board
All batteries must be shipped by a ground shipping method.
Spare battery for the HappyModel Moblite7 Whoop.
Check out the entire RDQ Series of LiPo and LiHV battery packs!
Specifications
Capacity: 650mAh
Max. Continuous Discharge Rate: 60C
Discharge Lead: 20mm, PH2.0
Dimensions: 60x18x8mm
Weight: 16g
Includes
1x HappyModel 3.8V 1S 650mAh 60C LiHV Micro Battery - PH2.0
Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season. This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability.
Check out the rest of pre-built quads and our HappyModel selection!
Features
X12 5-IN-1 AIO flight controller w/ built-in receiver and OpenVTX
VTX Power up to 400mw
RS0802 20000KV motors
RunCam Nano 3. The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible with 1S Lipo/LIHV
Specifications
Input Voltage: 1S
Max Continuous Current: 12A
Motors: 0802 20000KV
Camera: RunCam Nano 3
Wheelbase: 75mm
Dimensions: 99x99x40mm
Weight: 24g
Includes
1x HappyModel BNF 1S Mobula 7 Whoop - PNP
The HappyModel BNF 1S Mobula 7 HD Whoop version is a light and efficient 75mm brushless whoop which provides 1080P HD video recording functionality. HappyModel added blackbox for this 1s 75mm HD recording whoop so that you now have gyroflow functionality. Unlock the ultimate smooth flights with a combination of the Mob 7 HD and gyroflow!
Check out the rest of pre-built quads and our HappyModel selection!
Specifications
HappyModel X12 AIO
Input Voltage: 1-2S
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: MPU6000 or ICM20689 or BMI270
Max Continuous Current: 12A
VTX Output Power: 25-400mW
Antenna Connector: U.FL
OSD: Yes
Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX
ESC Firmware: Z_H_30_REV16_7
Mounting Pattern: 25x25mm
Weight: 5.1g
HappyModel RS Motor
Input Voltage: 1S
KV: 20000KV
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension: Φ10.5x13.5mm
Wire length(include connector): 30mm
Weight: 2g
Runcam Split 3 Lite
Video Resolution: 1080@60fps/1080@50fps/1080@30fps/720@60fps
Field of View(FOV): Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video File Format: MOV
Image Resolution: 2MP
Signal System: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Includes
1x HappyModel BNF 1S Mobula 7 HD Whoop
Introducing the Moblite7 Ultralight FPV Brushless Whoop! Made in collaboration with FPV pilot "Mr. Shutterbug," this whoop is one of the lightest 75mm drones on the market! And glows in the dark!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 36g With battery
Propellor Size: 75mm
Antenna: Linear Dipole
HappyModel DiamondF4 FR FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CrazybeeF4F
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (3sec)
ESC Firmware: BLheli_S
Factory firmware: O_H_50_REV16_8.HEX
Stack Size: 25x25mm
Dimensions: 29x29mm
Motors
Stator Size: 0802
Kv: 19000
Weight: 1.7g
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x 75mm Frame (Mobula7 frame)
1x Option1: DiamondF4 FR built-in SPI Frsky receiver
4x EX0802 KV19000 Unibell brushless motor
1x HQPROP 40MMX2 propeller(4cw+4ccw)
1x Runcam Nano3
1x Built-in 5.8G 40ch 25mw-200mw VTX
2x 1s 650mah Lipo battery
1x Propeller disassemble tool
1x Screwdriver
1x Happymodel Carry case
The Happymodel Moblite7 HDZero Whoop is a 75mm HD brushless whoop weighing just 29.5 grams. It features the HDZero Whoop Lite VTX and Nano Camera and a built-in SPI ELRS 2.4GHz or FrSky 2.4GHz receiver. With powerful EX1002 KV20000 motors and a Superbee F4 Lite flight controller, this should be a great performing high-definition whoop you can fly just about anywhere.
UART ELRS v3.0 ready
Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
The lightest 1S 75mm brushless whoop
Powerful and efficiency
The lightest 1S AIO 5IN1 F4 flight controller
1002 brushless motors
Low-profile Canopy design
HD Zero
Specifications
Wheelbase: 75mm
Size: 97x97x25mm
Weight: 19.5g (without battery)
Weight: 36g
Motor
Model: EX EX1002 20000KV
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.Len): Φ13.5mmx12.5mm
Weight(g): 2.5
No.of Cells(Lipo): 1S only
Flight Controller
SPI ELRS version Firmware target: CrazybeeF4SX1280
SPI FRSKY version Firmware target: CrazybeeF4FR
MCU: STM32F411CEU6 (100MHz, 512K FLASH)
Sensor: ICM20689 or ICM42688P or BMI270(SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/ELRSreceiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC
MCU Upgraded to EFM8BB21
Power Supply: 1S LiPo/LiPo HV
Current: 5A continuous, peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory Firmware: O_H_50_REV16_8.HEX
Default Protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version
SPI BUS receiver Frsky D8/D16 compatible
Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt)
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol
Onboard ELRS Receiver Version
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could bind with ELRS V2.0 firmware TX module
Onboard 5.8G 40CH 25-200mW VTX
Output Power: 25mw~200mw switchable
Frequency: 40CH
Input Voltage: 3.3V 5.5V
Current Consumption: 300mA (type)
Frequency: 5.8GHz 5bands 40 channels (include Race band)
Smart-audio Ready
HDZERO NANO LITE CAMERA SPECIFICATIONS:
Dimensions: 14x16x11 mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMOS sensor
Excellent low light performance
FOV:4:3: D:130° H:108° v:84°16:9:D:122° H:108° V:65°
Includes
1 x HappyModel BNF Moblite7 HDZERO 1S 75MM Brushless HD Whoop
1 x Moblite7 Spare Canopy
1 x Gemfan 1610 propeller Set (4cw+4ccw)
1 x Propeller disassemble tool
1 x Screwdriver
All batteries must be shipped by a ground shipping method.
Equipped with an ExpressLRS built-in SPI receiver, you'll never have to worry about range when whooping! This version of the Mobula6 also has another new feature: 0802 19000Kv motors! These motors are some of the lightest brushless whoop motors. Lighter whoops are easier to fly and super fast.
ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable.
This version comes pre-installed with ELRS 2.4GHz and ELRS V2.0!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 18.7g
Recommended Battery: 1S 300mAh
Propellor Size: 65mm
Antenna: Linear Dipole
HappyModel Crazy F4 FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CRAZYBEEF4DX
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (10sec)
ESC Firmware: BLheli_S
Stack Size: 25x25mm
Dimensions: 29x29mm
Weight: 5g
Motors
Stator Size: 0802
Kv: 19000
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x HappyModel BNF Mobula6 ELRS 65mm Brushless Whoop - ELRS 2.4GHz
4x 1S 300mAH Batteries
All product containing lithium batteries must be shipped by a ground shipping method. Please be aware Betaflight 4.3.1 firmware has a bug, Please do not flash version 4.3.1.
This is the V2 version of the Mobula 6 HD. This version features an ICM20689 Gyro as well as an OpenVTX 400mW VTX.
The Highly sought after Mobula6 now comes in HD! Record all your sessions in HD with the onboard RunCam split 3 Lite.We recommend RDQ 1S 300mAh LiPos for this whoop! Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
Extreme light 1S 65mm Brushless HD whoop only 27g
Come with Runcam Split3-lite 1080P HD DVR
Smooth and agile
Compatible for 1S Lipo/LIHV
Camera Angle adjustable
Specifications
Wheelbase: 65mm
Size: 80x80x40mm
Weight: 27g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Internal SPI DSM2/DSMX version(Compatible with SPEKTRUM DSM2/DSMX protocol radio transmitter)
External TBS CRSF NANO version(Compatible with TBS Transmitters)
Motors
Model: EX0802 19000KV
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Shaft Diameter: Φ1mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Weight(g): 1.7g
No.of Cells(Lipo): 1S only
Flight Controller
(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
(DSM2/X SPI RX version) CRAZYBEEX DXS DSM2/X version firmware target: CrazybeeF4DXS
(External TBS CRSF NANO RX version) CRAZYBEE F4 Lite Firmware target: CrazybeeF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G 400mW VTX
Built-in SPI Frsky/Flysky/DSMX receiver
Built-in 5V 1A BEC
Built-in voltage detection
ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band Smart audio ready
Runcam Split3 Lite
Model: RunCam Split3-Lite
Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps
Video File Format: MOV
Image Resolution:2 MP
TV Mode: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
Hole Distance of Installation: 25.5*25.5mm
PCB Size: 29*29mm
Lens Module Size: 14*14mm
Lens Specs: M9
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
Working Current: 450mA @5V
Includes
1x Happy Model BNF Mobula 6 HD 1S Whoop Quad - Choose Your RX
HappyModel has been an amazing company, bringing us FPV enthusiast quality whoops to fly. Take a look at HappyModels first ever whoop on a 85mm frame. It comes with X12 series flight controller, EX1103 KV11000 motors and Gemfan Hurricane 2023 tri-blade propellers, all together gives this whoop an amazing performance for an extremely smooth flight.
Choose between PNP (No RX) and BNF (ELRS SPI 2.4)
Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and OPENVTX
VTX Power up to 400mw
ELRS V2.0 (Default), can be flashed to ELRS V3.0
EX1103 KV110000 motors
CaddxFPV Ant FPV camera
Smooth and powerful
Compatible for 1S-2S Lipo/LIHV battery
3D Printed Camera Lens Protector
User Manuals
ELRS (SPI)
PNP (No RX)
Specifications
Brand Name: Happymodel
Motor: EX1103 KV11000
AIO: X12 5-IN-1 AIO flight controller
Camera: CaddxFPV Ant FPV camera
Prop: Genfan 2023-3 propellers
Weight: 42.7g
Input Voltage: 1-2S
Wheelbase: 85mm
Size: 120mmx120mmx50mm
Motor Specifications
Model: EX1103 KV11000
Configuration: 9N12P
Stator Diamter: 11mm
Stator Length: 3mm
Shaft Diameter: Φ1.5mm
Motor Dimension(Dia.xLen): Φ13.5mmx15.5mm
Weight(g): 3.8g
No.of Cells(Lipo): 1-2S
Propeller Specifications
Weight: 0.88g
Material: PC
Pitch: 2.3inch
Props Dia: 52.17mm
Center Thickness: 5mm
Center Hole Dia: 1.5mm
Flight Controller Specifications
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689 or ICM42688P(SPI connection)
Mount hole size: 25.5mm x 25.5mm
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
Built-in voltage detection
Built-in current sensor
Onboard 4in1 ESC
Power supply: 1-2S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Firmware target: Z_H_30
Default protocol: DSHOT300
Support Bluejay firmware
Onboard SPI ELRS 2.4GHz Specifications
Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could flash FC firmware to support ExpressLRS v3.0 TX module
PNP Version Specifications
Full UART1 for external Receiver
Support CRSF/GHOST/SBUS/IBUS/DSMX protocol
IR1 pad(invert RX1) used for SBUS input
Includes
1x HappyModel BNF Mobula8 1-2S Brushless Analog Whoop - Choose Your Receiver
1x Gemfan Hurricane 2023 tri-blade propellers (4CW+4CCW)
1x Screw Driver
1x Extra camera canopy
Spare replacement Flight Controller for the Happymodel Mobula 6, and an all around incredible little TRUE AIO for any 1S brushless build!
Check out all our Whoop FCs, our Mobula 6 parts selection, and all Happymodel products!
Specifications
Flight Controller
(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
Onboard FrSky SPI D8 Receiver Version
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 model
Channels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Onboard FlySky SPI Receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
Onboard 5.8GHz VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio ready
Includes
1x HappyModel Crazybee F4 Lite 1S Whoop Flight Controller - Choose Your RX
The world's first AIO 5in1 whoop flight controller with built-in ExpressLRS receiver is coming out now. This F4 flight controller has a built-in 5A esc, VTX, OSD, high-performance 900MHz ExpressLRS receiver, it’s best for 1S Long Range and whooping.
Check out our other Whoop/Toothpick flight controllers, as well as the rest of our HappyModel selection!
Specifications
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CRAZYBEEF4DX
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (10sec)
ESC Firmware: BLheli_S
Stack Size: 25x25mm
Dimensions: 29x29mm
Weight: 5g
Includes
1x HappyModel Craz yF4 ELRS 900MHz Whoop/Toothpick AIO Flight Controller w/ 8Bit 5A ESC
An F405 chip FC with built-in Serial ELRS receiver, 4in1 12A ESC, and 8Mbp black box. Optimized layout, supports 1-2S Lipo/LiHV. Perfect for Tinywhoop/Cinewhoop/Toothpick. Betaflight/INAV compatible. 3 sets UARTs, 5V/3A & 9V BECs, barometer. Get performance to elevate your FPV. Experience exceptional agility and power for your racing and freestyle sessions. With this board, you'll have the perfect setup to take your flight to the next level.
Browse the rest of our Whoop AIO Boards and our Happymodel gear.
Specifications:
Brand Name: Happymodel
Item Name: CrazyF405HD ELRS 1-2S AIO Flight controller
Mount size: 25.5mmx25.5mm
Weight: 4.8g without power lead wire
Firmware target: BetaflightF4
Support 1-2S Lipo/LiHV battery
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
*When using 1s battery and high KV 0702/0802 motors, should set the startup power to 1100/1200
Includes
1x HappyModel Crazyf405 ELRS HD 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC & ELRS 2.4GHz RX
1x Power lead with a XT30 Connector
Wiring Diagram
Great motor for any whoop and a perfect replacement part for the Happymodel Mobula 6 HD.
We also carry these motors in multiple KV options.
Check out the rest of our Mobula 6 parts & accessories and all our Happymodel gear!
Features
The lightest 0802 brushless motors around the world only 1.7g
Double E-clip design, prevent Motor bell to flying off
Good Dynamic balance
Specifications
KV: 19000Kv
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Terminals: JST1.25mm
No.of Cells(Lipo): 1S LiPo
Wire length(include connector): 27mm
Weight: 1.7g
Includes
1x Happymodel EX0802 19000Kv Whoop/Micro Motor for Mobula 6 HD - CW
Great motor for any whoop and a perfect replacement part for the Happymodel Mobula 6 HD.
We also carry these motors in multiple KV options.
Check out the rest of our Mobula 6 parts & accessories and all our Happymodel gear!
Features
The lightest 0802 brushless motors around the world only 1.7g
Double E-clip design, prevent Motor bell to flying off
Good Dynamic balance
Specifications
KV: 25000KV
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Terminals: JST1.25mm
No.of Cells(Lipo): 1S LiPo
Wire length(include connector): 27mm
Weight: 1.7g
Includes
1x Happymodel EX0802 25000Kv Whoop/Micro Motor for Mobula 6 HD - CW
The Happymodel EX1002 is a 1002 brushless motor with 20000KV. This is a replacement motor for the Happymodel 1S HDZero Whoop.
Check out the rest of our Mobula 6 parts & accessories and all our Happymodel gear!
Specifications
Input Voltage: 1S
Kv: 20000Kv
Shaft Diameter: 1.5mm
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Motor Dimension: Φ10.5x13.5mm
Wire length(include connector): 30mm
Weight: 2g
Includes
1x HappyModel EX1002 20000Kv Brushless Motor
The Happymodel SE0702 11000KV are the direct replacement motors for the Bassline 2S, so RDQ has you covered! It will also work great one any 2" Toothpick style drone.
Check out our other micro motors, and all our HappyModel selection!
Specifications
Kv: 11000Kv
Input Voltage: 1SS LiPo
Configuration: 9N12P
Motor Dimensions: Φ13.5mm x 15.5mm
Stator Dimensions: Φ11mm x 3mm
Shaft Diameter: Φ1.5mm
Mounting Pattern: Φ7mm
Weight: 3.8g
Includes
1x HappyModel EX1103 11000Kv Micro Motor
4x Motor Screws
Note: this motor is sold by HappyModel as a mix of CW & CCW options. These should be interchangeable, but if for some reason the rotation of the motor is not going the direction you desire, then you can simply reverse the settings in BLHeli or swap any two motor wires to reverse the direction.
Gemfan's new 1.6" (40mm) bi-blades are a direct replacement for the HappyModel Mobeetle or the Happymodel 1S Mobula 7 but also work well on all quads that spin 40mm props!
Check out all our Micro Props and the rest of our Gemfan and HappyModel collections!
Specification
Propeller Diameter: 40mm
Pitch: 1
Shaft: 1.5mm
Blades: 2
Material: Poly Carbonate
Hub Thickness: 5mm
Weight: 6.4g
Includes
4x HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop
Classic 0802 stator rated to be capable of 20,000Kv for major power, a good sweet spot for high Kv motors, where you get that extreme power without cutting your flight time down. There is a clean metallic shine on the motor, and these motors are also a replacement for the Mobula7.
Check out our other Micro Motors, and all our HappyModel selection!
Features
Compatible with the Mobula7 and Mobula7 HD 1S Version
0802 Stator
CCW rotation or CW rotation
This micro motor comes with motor plugs, for easier installation.
Specifications
No. of Cells(Lipo): 20000KV compatible with only 1S lipo
Motor Dimensions: 10.5x13.5mm
Wire Length (without connector): 30mm
Item Name: RS0802 brushless motor
Brand Name: Happymodel
Shaft Diameter: 1.5mm
Terminals: JST1.25mm
Stator Diameter: 8mm
Configuration: 9N12P
Stator Length: 2mm
Rotation: CCW or CW
KV: 20000KV
Weight: 2g
Includes
1x HappyModel RS0802 20000Kv Micro Motor - Choose Your Version
The Happymodel SE0702 23000KV Brushless Motor is a perfect solution for your lightweight build. The lightest brushless motors all over the world, with a weight of only 1.46 grams. You can build an extremely lightweight whoop with these amazing motors. These are also the direct replacement motors for the Mobeetle 1S, so RDQ has you covered!
Check out our other micro motors, and all our HappyModel selection!
Specifications
Kv: 23000Kv
Input Voltage: 1SS LiPo
Configuration: 9N12P
Motor Dimensions: Φ9.5mm x 14mm
Stator Dimensions: Φ7mm x 2mm
Shaft Diameter: Φ1mm
Mounting Pattern: Φ7mm
Weight: 1.46g
Includes
1x HappyModel SE0702 0702 23000Kv Motor
4x Motor Screws
Note: this motor is sold by HappyModel as a mix of CW & CCW options. These should be interchangeable, but if for some reason the rotation of the motor is not going the direction you desire, then you can simply reverse the settings in BLHeli or swap any two motor wires to reverse the direction.
The lightest brushless motors all over the world, with a weight of only 1.46gram. You can build an extremely lightweight whoop with these amazing motors.
Check out our other micro motors, and all our HappyModel selection!
Specifications
Kv: 26000Kv
Input Voltage: 1SS LiPo
Configuration: 9N12P
Motor Dimensions: Φ9.5mm x 14mm
Stator Dimensions: Φ7mm x 2mm
Shaft Diameter: 1mm
Mounting Pattern: Φ7mm
Weight: 1.46g
Includes
1x HappyModel SE0702 0702 26000Kv Motor
The Happymodel SE0802 19000KV are the direct replacement motors for the Mobula 6 HD 1S, so RDQ has you covered! It will also work great on racing whoops and toothpicks!
Check out our other micro motors, and all our HappyModel selection!
Specifications
Kv: 19000Kv
Input Voltage: 1SS LiPo
Configuration: 9N12P
Motor Dimensions: Φ10.5mm x 14.9mm
Stator Dimensions: Φ8mm x 2mm
Shaft Diameter: Φ1mm
Mounting Pattern: Φ7mm
Weight: 1.9g
Includes
1x HappyModel SE0802 19000Kv Micro Motor
4x Motor Screws
Note: this motor is sold by HappyModel as a mix of CW & CCW options. These should be interchangeable, but if for some reason the rotation of the motor is not going the direction you desire, then you can simply reverse the settings in BLHeli or swap any two motor wires to reverse the direction.
Make your drone projects even better with this HappyModel SE0702 0702 28000Kv Micro Motor. Its high-quality design offers efficient operation and reliable performance, giving your projects the boost they need. Make the most of your flying with this micromotor. These motors come with a JST 1.25 plug-in piece for a secure connection for HappyModel boards as with BetaFPV too.
Check out our other Micro Motors, and all our HappyModel selection!
Specifications
Brand Name: Happymodel
Mode: SE0702
KV Option: KV28000
Configuration: 9N12P
Stator Diameter: 7mm
Stator Length: 2mm
Shaft Diameter: Φ1mm
Motor Dimension(Dia.xLen):Φ 9.5mmx14mm
Weight(g): 1.5g
No.of Cells(Lipo): 1S only
Includes
1x HappyModel SE0702 0702 28000Kv Micro Motor - Choose Rotation (CW or CCW)
4x Motor Hardware
It's finally here! The ultralight 1s 5a AIO of the future comes in at a clean 2.8g. This is the AIO that got the mobula6 HDZero whoop under 25 grams.
Be sure to check out all our Whoop FCs and our HappyModel gear collection!
Due to this flight controller being a spare part for Mobula6 HDZERO, the original default device for OSD is “MSP”
If you bought this flight controller and used it for an analog camera, you may need to change some settings. First, connect to Betaflight Configurator, then move to CLI command tab, and enter “set osd_displayport_device = MAX7456”, then reconnect Betaflight, and upload the osd font.
Specifications
Board size: 25 x 25
Power supply: 1S
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5V 1A BEC
Built-in voltage detection
MCU upgraded to EFM8BB21
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_8.HEX
Default protocol: DSHOT150/DSHOT300/DSHOT600
FRSKY SPI BUS RECEIVER
Frsky D8/D16 switchable
Compatible Non-EU transmitter in both D8 and D16 mode
Channels: 8ch or 16ch
Failsafe support
No ground interference (Transmitter and receiver 1 m from the ground): 300m
ELRS SPI RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could bind with ELRS V2.0 firmware TX module
Includes
1x HappyModel SuperBee F4 Lite AIO Whoop Flight Controller
1x PH2.0 Pigtail
1x Hardware Set
The new V4 frame for the Mobula 7, Moblite 7, Mobula 7 1S and Mobula 7 1S HD. This revision upgrades the chassis to be more rugged with a lower mounting point for flight controllers, and not block the USB port. Compared to the V2 frame, the weight has increased by 1g, but it is more resistant to falls and offers better stability.
Check out the rest of our Happymodel gear, Our Moblite 7 collection, and our Mobula 7 collection as well!
Specifications
Wheelbase: 75mm
Maximum Propeller size: 40mm
Color: White or Black
Weight: 5.4g
Includes
1x HappyModel V4 75mm Frame For Moblite 7 / Mobula 7 / Mobula 7 1S - Choose Color
Until now, 1S tiny whoops were the last type of FPV drone that couldn't be converted to digital video due to voltage and weight limits. HDZero Whoop Lite is here to meet these needs: HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g.
Check out all our Shark Byte gear, and our HDZero selection!
Features
Ultra-high sensitive CMOS sensor
Excellent low light performance
HDZero Nano Lite Camera
HDZero Whoop Lite VTX
Removal Shielding Box
Supports Smart Audio
Under 7g in Weight
Antenna Retention
4mm Thickness
1S-3S Input
Specifications
HDZERO WHOOP LITE VTX
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Resolution: 1280x720@60fps
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Weight: 7g total package
HDZERO NANO LITE CAMERA
Size: 14x16x11mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor
FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65°
Includes
1x HDZero Whoop Lite VTX
1x HDZero Nano Lite Camera
1x Dipole Antenna
1x 40mm Mipi Cable
1x Power/Uart Cable
2x Zip ties
4x Rubber Grommet
The HD Zero Whoop VTX is exactly what it sounds like. A small, lightweight whoop profile VTX for Shark Byte systems! Capable of sending a 720p 60FPS video feed at up to 200mW output power, and weighing under 6 grams! Pairs perfectly with the HDZero Nano Camera!
Check out all our Shark Byte gear, and our HDZero selection!
Features
720p 60FPS
Switchable 25mW & 200mW Output
Compatible with all Shark Byte / Byte Frost Receivers
Lightweight!
Specifications
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Dimensions: 32.5x32.5x6mm
Weight: 5.9g
Includes
1x HDZero Whoop VTX for Shark Byte
The HGLRC SPECTER 1002 21000Kv Motor is a quality brushless motor designed for use in RC drones. It offers powerful thrust, with 21000Kv impressive performance and excellent efficiency. Its lightweight construction is perfect for long-distance flights and high-speed races.
Check out our Micro Motors and all our HGLRC products!
Features
Brand new rotor appearance design, anodized two-color process
7075 aviation aluminum material, high-strength one-piece rotor
Customized N52H curved magnetic steel, strong magnetism, high torque
Super high temperature resistant 200° copper wire winding, the motor runs more stably
Imported Kawasaki silicon steel sheets, low loss stator, reduce heat generation and improve efficiency
New and optimized tuning, maintain high torque at low speed, linear power output when the throttle changes rapidly, and precise and fast response when turning
Alloy Steel Outlet Shaft, high strength and reduce the weight of the fuselage
Suitable for 65mm Tiny drone or 65mm toothpick drone
Specifications
Motor: 21000KV
Slot pole: 9N12P
Maximum continuous current: 13.5A
Maximum power: 85W
Input voltage: 1S
ESC:> 5A
Recommended propeller: 1.6-2 inches
Motor size: Φ13.59mx 8.25mm
Mounting hole: 3xM1.4-∅6.6
Weight: 2.5g (including wire)
Wire length：45mm
Includes
1x HGLRC SPECTER 1002 21000Kv Motor
4x M1.4 screws
iFlight Blitz F411 1S 5A Toothpick/Whoop Flight Controller w/ 25-50mW VTX & ELRS RX is perfect for all of your lightweight builds. It is a Flight Controller, ESC, Receiver and VTX all in one little board weighing in at 4.8g. Now using ExpressLRS with a built-in ELRS ceramic antenna!
Check out all our whoop flight controllers, and all our iFlight Products!
Specifications
Input Voltage: 1S
MCU: STM32F411
Gyro: BMI270
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
VTX: PIT/25/50mW
FC Firmware: IFLIGHT_BLITZ_F411RX
Current: 5A continuous and peak 6A (3 seconds)
Signal Support: Dshot, Oneshot, Multishot
ESC Firmware: O-H-30 BLS 16.8 (Supports BLHeliSuite)
Dimensions: 29x29mm, compatible w/ standard whoop framest
Weight: 4.8g
Includes
iFlight Blitz F411 1S 5A Whoop Flight Controller w/ 25-50mW VTX & ELRS RX
4x M2 Rubber Damper
1x Whip antenna
Wiring Diagram
The iFlight BLITZ M10 GPS w/ Compass provides reliable positional and directional data for your quad. Its advanced compass and GPS module allow for precise coordinates and real-time flight information for optimal navigation. This high-performance unit helps ensure safe and accurate flight paths for your craft. Always keep a quad when you add a GPS!
Check out our other GPS modules, as well as the rest of our iFlight Products
Features
Using the latest UBLOX M10 chip, lower power consumption, faster satellite search speed.
Built-in high precision compass QMC5883L.
Built-in Faraday capacitor, with 1-10Hz positioning update rate, which makes GPS have faster startup speed and satellite receiving speed.
18x18mm ceramic antenna provides the best balance and performance for current GPS modules, low power consumption, strong signal and light weight.
On-board LNA low noise amplifier and RF filter provide excellent working environment for GPS module.
Up to 10HZ refresh rate.
Built-in Flash, users can set GPS parameters by themselves using U-center or other software, configuration modification will be stored to Flash, no loss of parameters after power failure.
Pin Definitions
VCC: system main power supply, supply voltage is 5V, current is about 40mA when working
GND: Ground
RXD: data input
TXD: Data output
SDA: Serial Data - I2C Master/Slave Data
DCL: Serial Clock - I2C Master/Slave Clock
Light Indicator
Blue light, TX light, the blue light blinks on power up, indicating that there is data output.
Red light, PPS light, not positioned red light is not lit, 3D positioning, the red light began to flash
Specifications
Compass module: QMC5883L
Baud Rate: 4800bps-115200bps (Default - 115200bps)
Sensitivity: Tracking: -167dBm
Cold start: 26s
Hot start: 1s
Maximum height: 50000m
Maximum speed: 500 m/s
Speed accuracy: 0.05 m/s
Maximum acceleration: ≦ 4G
Refresh Rate: 10 Hz
GPS patch antenna size: 18x18 mm
Total dimensions: 20 x 21 x 6.5 mm
Weight: 5.2 g（±0.5g）
Input Voltage: 3.3-5.5 V, current 40mA
GPS pin definition: RX/TX UART
Compass pin definition: SDA/SLA
Includes
1x iFlight BLITZ M10 GPS & Compass (10th Gen)
1x Cable Set
The iFlight Commando 8 ExpressLRS Radio Transmitter is a game-style radio controller that comes with a built-in ExpressLRS module for best-in-class RF performance! Its compact size allows the user to easily carry it on trips or to the field. Full-featured and powerful, this is a great radio for any purpose.
Check out our iFlight collection and all our RC transmitters!
Features
Internal iFlight ExpressLRS (ELRS) transmitter (additional fan for cooling)
Market's lowest crystal frequency deviation (low packet loss, high-frequency stability)
Highest quality digital hall sensor gimbals for maximum precision
High-performance PCB Single and Dual Band (900/2400MHz) radio antenna
Inbuilt 4000mAh for up to 20h power (2x 2000mAh 18650 batteries)
Stock EdgeTX firmware with pre-installed Lua scripts
Several Gimbal Stick Ends available (stock 18mm)
Specifications
ExpressLRS 2.4GHz // Max Output 500mW
Radio Channels: 8
Input: Mini High Precision Digital Hall Gimbals with NMB bearings
Gimbal Stick Ends: Stock length 18mm
Charging: Type-C 20W Quick Charge
Battery: Built-in 4000mAh 1S2P 18650 Battery
Charging Connector: Type-C
Weight: 310g
ELRS Option Only (Single TX)
Single ELRS option includes 1x ELRS TX module (please select band) pre-installed in the back of the radio
A cooling fan is inside the flat back cover
Single Band or Dual Band antenna option (for future upgrades or module changes)
Dual Band antenna option for convenient multi-band use without changing the antenna
Button Functionality
2 x 5-Axis menu buttons for full OpenTX or EdgeTx control
2 x 2-position switches (not momentary)
2 x 3-position switches
Antenna Options
Single-Band (2.4GHz)
Band Options
The 900MHz as well as 2400MHz band have outstanding performance and long range capabilities. If you're not sure what to get, please checkout the official ELRS Long Range Competition to see what has been achieved.
What can I expect? Due to local regulations, the 915MHz FCC region seems to have a better performance than the 868MHz EU region. The 2400MHz band works great in any region, has a higher packet rate up to 500hz. This is not a common 2400MHz protocol and cannot be compared to anything prior on the market.
RF Power
868/915MHz system: SX1276
ExpressLRS 2.4GHz // Max Output 500mW
ExpressLRS 868/915MHz // Max Output 1000mW
BASE CC2500 2.4GHz Multiprotocol // Max Output 100mW
Radio Channels: 8
Input: Mini High Precision Digital Hall Gimbals with NMB bearings
Gimbal Stick Ends: Stock length 18mm
Charging: Type-C 20W Quick Charge
Battery: Built-in 4000mAh 1S2P 18650 Battery
Charging Connector: Type-C
Weight: 310g
Includes
1 x iFlight Commando 8 2.4GHz Radio Transmitter - ELRS
2 x 18650 Li-Ion batteries included (pre-installed)
The ISDT BG-8S is a multipurpose battery checker. It comes lots of great features to help check your batteries, receiver signals and even has a USB output that allows you to charge your phone or other devices. The display that can easily be seen in sunlight and has an easy to use menu system to show all functions and data.
Check out our other ISDT products!
Features
Battery voltage check
Battery balancing
Power bank for mobile devices
Receiver signal test and protocol analysis
Upgrade via USB port
Multi language support
Specifications
Working voltage: 5.0V - 36V
Input voltage 1s: 0.8V - 15V
Input voltage 2-8S: 0.8V - 4.8V
Battery cells: 1-8S
Voltage measurement accuracy: ±0.005V @ 4.2V
Balancing cells accuracy: <0.005V
Support USB charging: Q2.0/C3.0, BC1.2, Maximum output 12V/2A
Support smart battery: Charging and discharging setting, read battery info and usage history
Supported Batt. Type: LiHv (1-8S) / LiPo (1-8S) / LiFe(1-8S) / Lilon (1-8S) / NiMH/Cd(1-10S)
Display: 2.4” 320×240 260,000 color IPS LCD
Dimension: 80x55x19mm
Weight: 59g
Operating Temperature: 0-40℃
Working Humidity: 10%-90%RH (noncondensing)
Storage Temperature: -20-60℃
Storage Humidity: 5%-90%RH (noncondensing)
Includes
1x ISDT BattGo BG-8S Smart Battery Checker
