The ISDT Parallel Charging Board is an extremely high quality and safe balance board, charge up to 4 XT60 lipos at once.
Check out our other Battery Chargers and Accessories!
Specifications
Max Input Current: 40A
Max Output Current: 30A/Port
Max Balance Current: 2A
Balance Cells: 1s~8s
Plug: XT60
Balance Cable: 6S
Includes
1x ISDT Parallel Charging Balance Board
The Meteor65 frame has been upgraded to the Meteor65 Air Brushless Whoop Frame, reducing the minimum weight to an impressive 2.67 grams. This remarkable frame features enhanced strength and durability plus a new motor fixed slot and optimized low profile design, making it the ultimate choice for those seeking a Sub18g 65mm 1S Whoop drone with an ultra-light structure.
Check out all our whoop frames & accessories and all our BetaFPV gear!
Features
Weighing a mere 2.67g, this Meteor65 Air Brushless Whoop Frame exemplifies exceptional ultra-light structure while maintaining remarkable durability and crash resistance.
A groundbreaking addition to the 65mm frame, the inclusion of motor fixed slots enhances the convenience and stability of the motor installation.The low profile design effectively concentrates the whoop drone's gravity, optimizing its flight performance.
The deliberate increase in whoop duct diameter effectively mitigates the risk of propeller strikes, ensuring seamless compatibility with 0702 motors and 0802 motors, and 31mm propellers.
ComparisonBased on the Meteor65 frame, we have optimized and upgraded in many aspects, the details are as follows.
The duct diameter is enlarged from 32mm to 34.9mm, which improves compatibility and avoids propeller strikes.
The weight is reduced from 3.14g to 2.67g, making the flight more flexible, exemplifying the exceptional ultra-light structure of the 1S whoop drone. Both frames feature the same materials and durability.
With the low profile of frame, the drone's gravity center is more concentrated and improves the sense of compactness.
Motor Fixed SlotIn a groundbreaking development, the Meteor65 Air Brushless Whoop Frame has been added firstly with motor fixed slots, facilitating a more expedient and steadfast motor installation process. While misalignment has no measurable effect on motor efficiency, correct shaft alignment ensures the smooth, efficient transmission of power from the motor to the flight controller, reduces mechanical stress, and minimizes power wastage. For advanced pilots who have strict requirements for assembling the ultra-light 1S whoop drone, this new design undoubtedly adds the finishing touch.
Endless PersonalizationWe enhance frame structure design and also provide diverse color options for drone frames, enabling greater freedom for choice. This allows for aligning or color clashing the frame color with your drone's theme. And equipped with our various colors of ultra-light Micro Air Canopy adds more possibility of capturing the optimal image. Your drone will capture people's attention and showcase your unique personality and creativity.
Micro Air CanopyWe also have devised an exceedingly light Micro Air Canopy, weighing a mere 0.74g, that not only facilitates camera angle adjustment from 25° to 50° but also has antenna mounts, incorporated at the tail. If your goal is to optimize canopy functionality while minimizing weight to obtain a Sub18g 65mm Whoop, this option stands as the definitive choice.
Specifications
Item: Meteor65 Air Brushless Whoop Frame
Material: PP
Weight: 2.67g
Wheelbase: 65mm
Motor Mounting: 3-M1.4-6.6mm
Flight Control Installation Hole: 26×26mm
Battery Slot Size: 11.6×6.0mm
Color: Black, White, Transparent White, Transparent Blue, Transparent Purple, Transparent Green
Includes
1x Meteor65 Air Brushless Whoop Frame - Choose Your Color
NewBeeDrone Cockroach Brushless Extreme-Durable Frame 75mm
Design Intent:
For this frame, we worked to develop a platform that would neither fall below expectations nor limit the creativity of the FPV community. The Cockroach 75mm is lightweight and versatile. We improved durability and worked to deliver a vibrational signature that made tuning easier so you can get the most performance out of NewBeeDrone flight controllers and motors. Every gram of frame material was either added or taken away to ensure that what was left was there for a reason.
Lightweight and Durable:
We found a more forgiving and resilient material that doesn't sacrifice in weight or stiffness. Struts and other key support components have been redesigned to distribute and dissipate stress from crashes and falls with a total weight of 6.98g.
Traditional Looks and Geometry:
This 75mm Cockroach frame has adaptable FC locations and a multitude of additional mounting points across the frame. We delivered a frame that has 2 board locations with 1x1inch or 25.4x25.4mm hole spacing. One mounting location on the top and another below to mount an additional board like a DVR or a 4K HD recording board. The 2-board mounting adaptability allows for the possibility for a pusher-style flying configuration to be used as well.
1mm Carbon Fiber Plate
A 1mm carbon plate is included for increased durability insurance. Though the frame can be flown without it, the carbon allows for additional adaptability and opens the frame's use for exciting opportunities in a pusher-style configuration. Flip the frame over and install it. Please be aware, the motor screws that come with the 75mm frame are expected to be used with carbon fiber. If you choose to use them without the carbon fiber plate – the screws may contact the motor PCB.
This 75mm frame does not come with just one limiting battery mounting solution. We understand that depending on the utility and flying style, many people want to run one or two 300mah Nitro Nector Golds in the traditional battery position or in a ‘toilet-tank’ position. We have developed several printable, TPU battery mount solutions to use with the frame and are always open to your suggestions.
Included are 4 3D printed mounting tabs. Use 2 to mount one Nitro Nectar Gold 1s Battery and all 4 to mount 2x Nitro Nectar Gold 1s Batteries. When using 2 batteries, you can choose to run them in either series (2s) to increase voltage or parallel (1s) to increase capacity.
Easy and Inexpensive.
None of this is any good if it's super difficult to use and/or super expensive. So we made sure we set out to make something affordable. Key tolerances have also been fine-tuned to make installation and removal much easier.
Any of our other whoop BNFs can be directly dropped in into the 75mm frame.
Check out the rest of our micro frames and the rest of our NewBeeDrone products!
Specifications
Motor Mount Pattern: Tri 6mm
Weight: 3.71g
Includes
1x NewBeeDrone 75mm Cockroach Brushless Extreme Durable Whoop Frame
Introducing the NewBeeDrone Flow 0702 motor, designed for whoop racing. It weighs only 1.58g (1.38g without cables) and is equipped with double ball bearings for a smooth, durable performance. Crafted with 7075 aluminum, it stands strong against the toughest racing conditions. Experience peak performance and thrill with this ultimate motor choice. Get yours today and experience the thrill of racing like never before!
Check out our other micro motors and all our NewBeeDrone products!
Specifications
Motor KV: 27000 (Designed for 1S)
Internal Resistance (mΩ): 285
Stator Resistance (mΩ): 7
Stator Height (mm): 2
No.of Stator Slots: 9
No.of Rotor Poles: 12
Dynamic balance (mg): ≤10mg
NO-Load Current(A):P 0.80A
Maximum Power (W) 15.2
Maximum Current (A): 3.8
Overall Dimension(mm): Ø1xL12.2
Shaft Diameter(mm): 30AWGxL40
ESC(A):5
Rated Voltage(V): 4.2(1S)
Includes
1x NewBeeDrone Flow 0702 27000Kv Dual Ball Bearing Micro Motor 4 Pack
4x JST1.25 Whoop Motor Plug Replacement
16x M1.4x3 Screws
Introducing the NewBeeDrone Flow 0702 motor, designed for Whoop racing. It weighs only 1.58g (1.38g without cables) and is equipped with double ball bearings for a smooth, durable performance. Crafted with 7075 aluminum, it stands strong against the toughest racing conditions. Experience peak performance and thrill with this ultimate motor choice. Get yours today and experience the thrill of racing like never before!
Check out our other micro motors and all our NewBeeDrone products!
Specifications
Motor KV: 29000 (Designed for 1S)
Internal Resistance (mΩ): 275
Stator Resistance (mΩ): 7
Stator Height (mm): 2
No.of Stator Slots: 9
No.of Rotor Poles: 12
Dynamic balance (mg): ≤10mg
NO-Load Current(A):P 0.90A
Maximum Power (W) 15.2
Maximum Current (A): 3.8
Overall Dimension(mm): Ø1xL12.2
Shaft Diameter(mm):30AWGxL40
ESC(A): 5
Rated Voltage(V): 4.2(1S)
Includes
1x NewBeeDrone Flow 0702 29000Kv Dual Ball Bearing Micro Motor 4 Pack
4x JST1.25 Whoop Motor Plug Replacement
16x M1.4x3 Screws
NewBeeDrone's FLOW series now gets a 0802 motor. These 0802 19,000kv motors were selected to give an option to those who want that "FULL SEND" raw power on their 1s whoops. These brushless motors bring everything to the next level.
Check out our other 0802 motors, and all our NewBeeDrone selection!
Specifications
0802 Motor Size
19,000kv (Designed for 1s)
1mm Shaft size
Lead wire solder pads
JST-1.0 Plugs installed
50mm cable length
2.16g each
Includes
4x NewBeeDrone Flow 0802 19000Kv Micro Motors
4x JST1.25 Whoop Motor Plug Replacement
16x M1.4x3 Screws
NewBeeDrone's FLOW series now gets a 0802 motor. These 0802 25,000kv motors were selected to give an option to those who want that "FULL SEND" raw power on their 1s whoops. These brushless motors bring everything to the next level.
Check out our other 0802 motors, and all our NewBeeDrone selection!
Specifications
0802 Motor Size
25,000kv (Designed for 1S)
1mm Shaft size
Lead wire solder pads
JST-1.0 Plugs installed
50mm cable length
2.16g each
Includes
4x NewBeeDrone Flow 0802 25000Kv Micro Motors
4x JST1.25 Whoop Motor Plug Replacement
16x M1.4x3 Screws
Check out NewBeeDrone's Flow 0802 dual ball bearing whoop motor 27000kv (Set of 4)
NewBeeDrone's FLOW series now gets a 0802 motor. These 0802 27,000kv motors were selected to give an option to those who want that "FULL SEND" raw power on their 1S whoops. These brushless motors bring everything to the next level.
Check out our other 0802 motors, and all our NewBeeDrone selection!
Specifications
Motor KV: 27400
Maximum Current: 6.2Amp
Internal Resistance: 142mΩ
Maximum Power: 24.8W
Stator Diameter: 8.4mm
Overall Dimension:Φ11.6 x 12.2mm
Stator Height: 2mm
Shaft Diameter: Φ1 x 4.2mm
No.of Stator Slots: 9
Lead Wire Size: 30AWG x 50mm
ESC(A): 10Amp
Dynamic Balance: ≤10mg
Rated Voltage: 4.2V(1s)
NO-Load Current: 1.60Amp
Includes
4x NewBeeDrone Flow 0802 27000Kv Dual Ball Bearing Micro Motor 4 pack
4x JST1.25 Whoop Motor Plug Replacement
16x M1.4x3 Screws
We heard you asking for it, so we got it, the HummingBird F4 V2 Flight Controller, these AIO whoop style FCs are meant as replacements and upgrades for whoops/toothpick builds. This board is also the direct replacement board for NewBeeDrone BNF Hummingbird F4 V2.1 1S Brushless Whoop.
Check out all of our AIO Flight Controllers and our NewBeeDrone products for sale at RaceDayQuads!
Specifications
STM32F411 MCU (for the main controller (Preloaded with Betaflight)
Support 1S battery ONLY
Current sensor onboard
ESC-12A Per Motor Channel BB21 MCU
BlHeliS Support DShot(150 300 600) Multishot
Gyro- BMI270
Onboard Sideway RGB LED controlled by Betaflight
Support BeeSign signal compatible with NBD VTX-Camera System
Onboard Diversity SPI SX1280 Receiver(EXPRESSLRS)
MotorPlug JST1.0
NBD OSD(Betaflight OSD Compatible)
5V 2A Power support for external VTX Camera Or Receiver.
Includes
1x BeeBrain BLV4 Flight Controller
4x Grommet
1x Mounting Kit
1x Receiver Antennas
1x VTX Antenna
Wiring Diagram
All batteries must be shipped by a ground shipping method.
NBD is excited to introduce the Nitro Nectar Gold Series HV Lipo Battery Series! They use a different battery packaging technology that provides a better discharging rate for those who like to push the limit! They tested these batteries with their powerhouse 1S craft, the AcroBee BeeBrain BL BNF and they are built to keep up with the demand of raw thrust! After 3 months testing, NewBeeDrone is ready to bring them to the market for whoop pilots across the world!
Lightweight, durable and plenty of power to bring home the Gold!
Check out our 1S battery selection, and all our NewBeeDrone gear!
NOTE: These packs are designed to deliver a major amount of power! With the discharge rate that gives these packs such power, you will feel pack sag much later than normal packs. We suggest setting the low voltage reading to 3.5v and bringing it in to land at 3.3v. You are able to fly below 3.3v but that may result in battery degradation. You will need a high voltage capable charger, such as our brand new Nectar Injector portable USB powered charger.
Specifications
Cell count: 1
Nominal voltage: 3.8V
Max voltage: 4.35V
Capacity: 300mah
Continuous discharge rating: 40C
Max discharge rating: 80C
Dimensions: 62mm x 10.5mm x 6.5mm
Weight: 8.10g (+/-1%)
Plug: PH 2.0 or GNB27
Wire Length: PH2.0 None, GNB27 50mm
Watt hours: 1.14 Wh
Includes
1x Nitro Nectar Gold 3.8V 1S 300mAh 30/60C LiHV Whoop/Micro Battery
This adapter will allow you to connect your Ph2.0 cables to you 1S battery checker.
Check out the rest of our pigtails, connectors and adapters!
Includes
1x PH2.0 Adapter Cable Set for 1s LiPo Checkers
PTK-5105-22, ProTek RC 1S 130C Low IR Si-Graphene + HV LiPo Battery (3.8V/8800mAh) w/4mm Connectors (ROAR Approved)
The ProTek R/C 1S 130C Graphene + HV 8800mAh LiPo Battery is a great battery option for any racer looking for a lightweight, 1S battery. Weighing 155 grams, the 8800mAh capacity 1S HV offers huge current delivery that provides the punch needed for demanding 1S classes.
When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage - but Graphene + 130C LiPo batteries take that a step further with more power and lower internal resistance when compared to the previous ProTek LiHV Graphene packs!
Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 3.7V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for racers and bashers that demand the absolute best.
This product was added to our catalog on January 24, 2022
PTK-5184, ProTek RC 1S High Power Micro Heli/Airplane 25C LiPo Battery (3.7V/160mAh)
This is the ProTek R/C 1S 160mAh, 25C Micro Helicopter/Airplane Lithium Polymer battery pack. This pack will fit E-Flite and Parkzone products that use 70mah to 150mAh battery packs. When used in aircraft that normally use 70mAh batteries, these batteries will provide better performance and longer flight times!
Specifications:
Type: Lithium Polymer
Capacity: 160 mAh
Voltage: 3.7V nominal
Connector Type: Molex
Number of Cells: 1
Weight: 4g
Dimensions: 43x12x5mm (1.75x.5x.25")
Maximum Charge Rate: 1C (160mAh)
Maximum Continuous Discharge: 25C (4.0A)
This product was added to our catalog on May 18, 2021
The GTS V3 0802 Motor is a powerful new motor by RCINPOWER! Choose a Kv option: 22000Kv, 25000Kv, 27000Kv.
Take a look at all of our micro motor selections and our RCInPower collection!
Specification:
Kv: 22000
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Shaft Diameter: 1mm (1.5mm inside)
Motor Dimensions (Dia. x length): Φ 11.2x8.2mm
Weight: 1.97g (with plug)
Idle Current(5)@5V(A): 0.2
No. of cells (Lipo): 1S
Max Continuous Power: 21.5
Internal Resistance: 117mΩ
Max Current: 5.8A
Max Efficiency Current: (1-2A)>82%
Includes
1x RCInPower GTS V3 0802 22000Kv Motor
The GTS V3 0802 Motor is a powerful new motor by RCINPOWER! Choose a Kv option: 22000Kv, 25000Kv, 27000Kv.
Take a look at all of our micro motor selections and our RCInPower collection!
Specification:
Kv: 25000
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Shaft Diameter: 1mm (1.5mm inside)
Motor Dimensions (Dia. x length): Φ 11.2x8.2mm
Weight: 1.97g (with plug)
Idle Current(5)@5V(A): 0.25
No. of cells (Lipo): 1S
Max Continuous Power: 24.1
Internal Resistance: 105mΩ
Max Current: 6.5A
Max Efficiency Current: (1-2A)>82%
Includes
1x RCInPower GTS V3 0802 25000Kv Motor
The GTS V3 0802 Motor is a powerful new motor by RCINPOWER! Choose a Kv option: 22000Kv, 25000Kv, 27000Kv.
Take a look at all of our micro motor selections and our RCInPower collection!
Specification:
Kv: 27000
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Shaft Diameter: 1mm (1.5mm inside)
Motor Dimensions (Dia. x length): Φ 11.2x8.2mm
Weight: 1.97g (with plug)
Idle Current(5)@5V(A): 0.3
No. of cells (Lipo): 1S
Max Continuous Power: 26.6
Internal Resistance: 95mΩ
Max Current: 7.2A
Max Efficiency Current: (1-2A)>82%
Includes
1x RCInPower GTS V3 0802 27000Kv Motor
Transform your FPV experience with the RCINPOWER GTS V3 1003 22,000Kv Brushless Motor. This motor boasts impressive power, speed, and torque and will leave you stunned. Dare to go faster, farther, and higher than you ever have! Choose between orange with gold accents or blue with pink accents. This motor comes with a a solderless motor connector.
This motor is also available 10,000Kv and 18,000Kv
Check out our micro motors and all our Rcinpower products!
Features
Enables agile and efficient flight maneuvers
Designed specifically for FPV enthusiasts
Compact and powerful microdesign
Specifications
KV: 22000
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 3mm
Shaft Diameter: 1.5mm
Motor Dimension: 13.5x9.2mm
Weight: 3.45 Grams (5cm Wires)
Idle Current (5 Seconds)@4V: 1.5A
No. Of Cells (Lipo): 1S
Max Continuous Power (W) 3S: 67
Internal Resistance: 46mΩ
Max Current (3S): 18.1A
Max. Efficiency Current: (1-3A)>84%
Includes
1x RCinPOWER GTS V3 1003 22,000Kv Micro Motor - Choose Color
Rcinpower is known for creating some of the highest quality brushless motors on the market. Try out a set of these new GTS-V3 motors and find out what all the hype is about!!
Check out our huge motor selection and all our Rcinpower products!
Specifications
Kv: 19000
Input Voltage: 1S
Configuration: 9N12P
Max Continuous Current: 11.8A
Internal Resistance: 89mΩ
ldle Current@5V: 1.3A
Motor Dimensions: 13.5x7.75mm
Stator Dimensions: 10x2mm
Shaft Diameter: 1.5mm
Mounting Pattern: 9x9mm
Weight: 2.5g
Includes
1x Rcinpower GTS-V3 1002 19000Kv Motor
Rcinpower is known for creating some of the highest quality brushless motors on the market. Try out a set of these new GTS-V3 motors and find out what all the hype is about!!
Check out our huge motor selection and all our Rcinpower products!
Specifications
Kv: 22000
Input Voltage: 1S
Configuration: 9N12P
Max Continuous Current: 14A
Internal Resistance: 75mΩ
ldle Current@5V: 1.5A
Motor Dimensions: 13.5x7.75mm
Stator Dimensions: 10x2mm
Shaft Diameter: 1.5mm
Mounting Pattern: 9x9mm
Weight: 2.5g
Includes
1x Rcinpower GTS-V3 1002 22000Kv Motor
**3.3 VOLTS ONLY - DO NOT USE 5 VOLTS!**
We recommend an input voltage of 3.3v. The result may not be immediate, but eventually supplying voltage out of component limits will kill it. Always verify prior to install that your system is giving the GPS the voltage you think it is via a multimeter. If your unit dies or fails to operate as you'd expect, this is likely the cause.
The RDQ Micro M8N GLONASS GPS Module is 18x18mm in size, perfect for any Micro , or add Gps to your racer to add "lost tracker" . Only 6 Grams with cable.
Note: Providing the GPS with over the spec'd voltage WILL destroy your unit.
Check out our GPS selection!
Joshua Bardwell says: "In the video above, I mistakenly power the GPS with 5v. The GPS needs 3.3v power, not 5v. Powering the GPS with 5v will destroy it."
Specifications
GPS: UBLOX NEO-M8N Micro
TX LED: blue the data output, TX LED flashing
PPS LED: red PPS LED not bright when GPS not fixed,flashing when fixed
Current: Capture 50mA/5.0V
VCC : DC Voltage 2.7V-3.6V
Chip used is always the UBX-M8030
Acquisition Time:
Cold Start : 26s
Warm start : 25s
Hot start : 1s
UBLOX protocol /NMEA-0183
Receiving Format
GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS
Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1
Channels : 72 Searching Channel
Includes
1x MINI GPS
1x Cable
1x Adhesive pad
Setup
More information about GPS Rescue Mode
How to add a GPS in Betaflight 3.2
With the 3.2 release, Betaflight finally has decent GPS support. Here are some of the navigation features you can have on Betaflight OSD:
Latitude
Longitude
Distance to home
Speed
Arrow pointing home
Even better: if you have a telemetry-enabled receiver such as the X4R or XSR, you can send your location to the Taranis in real time. The Taranis will log your position, and keep the last known position available in case of a crash. This means it could save you time and maybe money in the long run. This unit comes preconfigured and ready to wire to a flight controller. However, if you want to mess with the settings you can configure it via a serial UART and u-center for Windows. This video is still mostly relevant if you need to do that. Wiring the gps unit is easy: just connect it to a free UART on your flight controller. Make sure that the wires are long enough that you can mount the gps on top of your quad. If you are running a bottom mounted battery, the top of your HD camera mount is the best spot. I run a top mount, so I prefer heat shrinking the gps to a battery strap so I can have it on top of the battery. Once wired, configuring the gps is easy. On the ports tab of Betaflight, select gps as a peripheral for the UART to which it’s wired. In this case I used UART 3. Then in the configuration tab: And if everything is wired correctly, when you restart betaflight you should see the GPS indicator light up at the top of the screen. Now there are two things you can do. If you have Betaflight OSD, you probably want to enable gps coordinates, distance to home and direction to home. I also like having the satellite count and gps speed, even though it’s not very accurate. My screen looks like this: The home arrow indicates that I’m flying mostly away from myself and 145 meters away. The GPS coordinates show that I am in… [left as an exercise for the reader]. The second thing you could do is set up your Taranis to log gps coordinates (assuming your receiver has telemetry, won’t work with an xm+). I won’t cover that now because this is enough for one post, I’ll save it for a future one. Happy flying and hope this saves you from losing a quad or two!
All batteries must be shipped by a ground shipping method.
RDQ Series Lipos are known and loved by the community for their strong performance and solid reliability flight after flight, all while offering an unmatched level of value!
Check out the entire RDQ battery line!
Specifications
Capacity: 550mAh
Continuous Discharge Rate: 90C
Dimensions: 6x18x66mm
Discharge Lead: 12mm
Weight: 14g (+/- 1%)
Includes
1x RDQ Series 3.7V 1S 550mAh 90C LiPo Battery w/ Cabled Connector
All batteries must be shipped by a ground shipping method.
RDQ Series Lipos are known and loved by the community for their strong performance and solid reliability flight after flight, all while offering an unmatched level of value!
Check out the entire RDQ battery line!
Specifications
Capacity: 550mAh
Continuous Discharge Rate: 90C
Dimensions: 6x18x66mm
Discharge Lead: 12mm
Weight: 14g (+/- 1%)
Includes
1x RDQ Series 3.7V 1S 550mAh 90C LiPo Battery w/ Plastic Head
All batteries must be shipped by a ground shipping method.
RDQ Series batteries are made to be a perfect blend of power and value. These batteries perform powerfully and evenly through the voltage range.
Check out our other 1S batteries, as well as the rest of our RDQ battery selection!
Specifications
Nominal Voltage: 3.8V
Cells: 1S
Capacity: 300mAh
Discharge Rate: 60C
Composition: Li-Ion
Discharge Lead: PH2.0 Plastic Head
Dimensions: 56x13.3x6.5mm
Weight: 6.7g
Includes
1x RDQ Series 3.8V 1S 300mAh 60C LiHV Battery - PH2.0
All batteries must be shipped by a ground shipping method.
The new RDQ 1S 380mAh HV is a lighter and more compact battery compared to its 350mAh counterpart.
This pack is perfect for whoops running on 1s.
Get the discounted 10 Pack here!
We also carry a plastic head version of this pack!
This new battery will fit perfectly in the Mobula7 and Beta65x whoop with no modification or additional adapters.
Check out the rest of our RDQ Series batteries.
Specifications
Capacity: 380mAh
Connector: PH2.0
Dimensions: 6.36x11.1x62mm
Weight: 8g
Includes
1x RDQ Series 3.8V 1S 380mAh 1S 60C LiHV Whoop/Micro Battery - PH2.0
All batteries must be shipped by a ground shipping method.
The new RDQ 1S 380mAh HV is a lighter and more compact battery compared to its 350mAh counterpart.
This pack is perfect for whoops running on 1s.
Get the discounted 10 Pack here!
We also carry a pigtailed version of this pack!
This new battery will fit perfectly in the Mobula7 and Beta65x whoop with no modification or additional adapters.
Check out the rest of our RDQ Series batteries.
Specifications
Capacity: 380mAh
Connector: PH2.0
Dimensions: 6.36x11.1x62mm
Weight: 8g
Includes
1x RDQ Series 3.8V 1S 380mAh 1S 60C LiHV Whoop/Micro Battery - PH2.0 Plastic Head
All batteries must be shipped by a ground shipping method.
The RDQ Series of LiPos now includes the perfect solution for your EMAX Tiny Hawk!
Also available in a 5 pack.
Specifications
Capacity: 450mAh
Dimensions: 62x17x6.9mm
Includes
1x 3.8V 1S 450mAh 80C LiHV Battery
All batteries must be shipped by a ground shipping method.
The RDQ Series Lipo Batteries now has the perfect solution for your EMAX Tiny Hawk!
Specifications
Nominal Voltage: 3.8V
Capacity: 525mAh
Discharge Lead: PH2.0,
Dimensions: 65x17x6.7mm
Weight: 13g
Includes
1x RDQ Series 3.8V 1S 525mAh 80C LiHV Whoop/Micro Battery
All batteries must be shipped by a ground shipping method.
RDQ Series Lipos are known and loved by the community for their strong performance and solid reliability flight after flight, all while offering an unmatched level of value!
Check out the entire RDQ battery line!
Specifications
Capacity: 550mAh
Continuous Discharge Rate: 100C
Dimensions: 6x18x66mm
Discharge Lead: 12mm
Weight: 14g (+/- 1%)
Includes
1x RDQ Series 3.8V 1S 550mAh 100C LiHV Battery w/ Cabled Connector
All batteries must be shipped by a ground shipping method.
RDQ Series Lipos are known and loved by the community for their strong performance and solid reliability flight after flight, all while offering an unmatched level of value!
Check out the entire RDQ battery line!
Specifications
Capacity: 550mAh
Continuous Discharge Rate: 100C
Dimensions: 6x18x66mm
Discharge Lead: 12mm
Weight: 14g (+/- 1%)
Includes
1x RDQ Series 3.8V 1S 550mAh 100C LiHV Battery w/ Plastic Head
All batteries must be shipped by a ground shipping method.
Another great HV LiPo choice in the RDQ Series. 125mAh more than the popular 1S 525!
Check out the entire RDQ Series of LiPo and LiHV battery packs!
Specifications
Capacity: 650mAh
Max. Continuous Discharge Rate: 60C
Discharge Lead: 20mm, PH2.0
Dimensions: 58x18x8mm
Weight: 14.5g
Includes
1x RDQ Series 3.8V 1S 650mAh 60C LiHV Battery - PH2.0
All batteries must be shipped by a ground shipping method.
The RDQ battery line is the perfect cross-section between value, and performance. Aimed at giving a great flight experience, while not breaking the bank, these batteries are perfect for pilots of all skill levels.
Check out our other 1S batteries, as well as the rest of our RDQ products!
Specifications
Nominal Voltage: 3.8V
Cells: 1S
Capacity: 660mAH
Discharge Rate(Cont./Burst): 90C
Discharge Lead: PH2.0 20mm
Dimensions: 58x18x7.8mm
Weight: 15.5g
Includes
1x RDQ Series 3.8V 1S 660mAH 90C LiHV Whoop/Micro Battery - PH2.0
All batteries must be shipped by a ground shipping method.
The RDQ battery line is the perfect cross-section between value, and performance. Aimed at giving a great flight experience, while not breaking the bank, these batteries are perfect for pilots of all skill levels.
Check out the rest of our 1S batteries, as well as the rest of our great RDQ products.
Specifications
Capacity: 720mAh
Max. Continuous Discharge: 100C
Dimensions: 65.5x18x7.5mm
PH2.0 Lead: 13mm
Weight: 17g
Includes
1x RDQ Series 3.8V 1S 720mAh 100C LiHV Whoop/Micro Battery - PH2.0
All batteries must be shipped by a ground shipping method.
Another great HV LiPo choice in the RDQ Series.
Check out the entire RDQ Series of LiPo and LiHV battery packs!
Specifications
Capacity: 850mAh
Connector: PH2.0
Dimensions: 67x18x7.5mm
Weight: 16.6g
Includes
1x RDQ Series 3.8V 1S 850mAh 60C LiHV Whoop/Micro Battery
This 3D print is meant to adapt the RDQ Series 300mah 2S 70C 7.6V HV FPV Micro Battery to several of the 2S whoops that we carry. The Mobula7 V1 or V2 frame adapter is meant to carry (2x) of the 250mah 3.8v HV 1s PH2.0 RDQ Whoop Battery.
The Whoops the print is designed for are:
Mobula7 V1 or V2 Frame
Mobula7 V3 Frame
Beta75 Pro Frame
Beta75X 2S Frame
Dont forget to check out all of our whoop products!
Check out all our 3D printed accessories!
Includes
1x RDQ Series Battery Adapter for Mobula7 and BetaFPV Whoop Mod
This is your mobile FPV swiss army knife! You can flash and configure your FC & BLHeli_S ESCs, download and analyze your blackbox logs, check your 1-6S LiPo voltages, and fast charge your mobile device from a LiPo! Featuring WiFi & Bluetooth radios, XT60 & PH2.0 power inputs and Micro USB, USB-C & USB-A connectivity, there's not much this little device can't do!
Download the App for Android and iOS
Check the rest of our tools & building supplies and our SpeedyBee products!
Features
Wireless Firmware Flasher & Configurator
30W Fast USB Charger
Wireless Blackbox Analyser
Wireless ESC Flasher
1-6S LiPo Checker
iOS & Android Compatible
USB-C & Micro USB
Specifications
Input Voltage: 1-6S(3.8V+ for 1S)
Power Input Connector: XT60-Male, PH2.0 male
Required Mobile Device System Version: Android 7.0+ | iOS 12.0+
Supported SpeedyBee App Version: V1.6.1 + for iOS | V1.5.6+ for Android
Maximum Output Current for flight controllers: 700mA @5V
Fast Charging Output interface: USB A Port
Minimum Input Voltage for Charging output: 7.4V(2S LiPo)
Supported Fast Charging Protocol: QC3.0/QC2.0, AFC, FCP, SCP/High SCP, PE2.0/PE1.1, SFCP
Max Fast Charging Current: 3.5A
Max Fast Charging Power: 30W
Case Material: ABS + PC
Liquid Silicone Cable Length: 12.4cm
Dimension(Main Body): 24.8x21.8x53.6mm
Net Weight: 35g
Manual Download
Includes
1x Speedy Bee Adapter 3
Sub250's M2 1002 brushless motor is specially designed for 1.6-2 inch FPV Drones, with strong power, small size and lightweight design. It uses imported N52H magnetic steel and high-temperature resistant coil, ball bearings, and a three-blade rotor for good structural rigidity and heat dissipation.
Check out the rest of our pre-built quads, as well as the rest of our Sub250 selection!
Features
Small in size and lightweight, only 2.6g.
N52H strong magnetic magnet, high-temperature resistant coil, full of power.
Using imported ball bearings, the motor has high efficiency and long service life.
Low loss stator, low heat generation, and high efficiency.
With fine motor dynamic balance adjustment, the motor runs smoothly and stably.
Suitable for 1.6 -2 inch mini FPV drones.
The 1.5mm shaft diameter is suitable for most propellers on the market.
Specifications
Brand Name: Sub250
Product: M2 1002 Brushless Motor
KV value: 14000
Working voltage: 4.35V (1S)
Configuration: 9N12P
Stator diameter: 10mm
Stator height: 2mm
Outlet diameter: Φ1.5mm
Dimensions: Φ13.83mm x 7.75mm
Magnet: N52H
Weight: 2.6g (5cm wire)
Applicable model: 1.6- 2-inch FPV drones
Recommended battery: 1S 380mAh-530mAh LiPo
Includes
1x Sub250 1002 14000Kv Micro Motor - Black/Blue (1.5mm Shaft)
4x M1.4 x 3mm screw
Sub250's M2 1002 brushless motor is specially designed for 1.6-2 inch FPV Drones, with strong power, small size and lightweight design. It uses imported N52H magnetic steel and high-temperature resistant coil, ball bearings, and a three-blade rotor for good structural rigidity and heat dissipation.
Check out our vast motor selection as well as the rest of our Sub250 selection!
Features
Small in size and lightweight, only 2.6g.
N52H strong magnetic magnet, high-temperature resistant coil, full of power.
Using imported ball bearings, the motor has high efficiency and long service life.
Low loss stator, low heat generation, and high efficiency.
With fine motor dynamic balance adjustment, the motor runs smoothly and stably.
Suitable for 1.6 -2 inch mini FPV drones.
The 1.5mm shaft diameter is suitable for most propellers on the market.
Specifications
Brand Name: Sub250
Product: M2 1002 Brushless Motor
KV value: 21000
Working voltage: 4.35V (1S)
Configuration: 9N12P
Stator diameter: 10mm
Stator height: 2mm
Outlet diameter: Φ1.5mm
Dimensions: Φ13.83mm x 7.75mm
Magnet: N52H
Weight: 2.6g (5cm wire)
Applicable model: 1.6- 2-inch FPV drones
Recommended battery: 1S 380mAh-530mAh LiPo
Includes
1x Sub250 1002 21000Kv Micro Motor - Black/Silver (1.5mm Shaft)
4x M1.4 x 3mm screw
All batteries must be shipped by a ground shipping method.
Sub250 1S 380mAh 3.8V LiHV High-voltage lithium battery is specially designed for Indoor Micro FPV drones. It is small volume, lightweight, and High capacity. It can discharge up to 90C, providing sufficient power for flight. Sub250 LiHV 1S battery’s USB charging board is used for charging, It’s extremely convenient and High-efficiency!The full charge voltage of the battery is 4.35V, the battery needs to be charged in time when the flight voltage drops to 3.6V!
Specifications
Weight: 9.7g
Capacity: 380mAh
Dimensions: 48x17x6.5mm
Max cont. discharge (C-rate/current): 90C
Charge Connector: GNB27
Includes
6x 3.8V 1S 380mAh 90C LiHV Batteries for Nanofly16
Warnings From Manufacturer:
Please read the battery parameters and instructions in detail before use.
Please don’t charge the battery unattended.
Do not overcharge (select the correct battery type before charging, the full charge voltage of a single cell of LiPo battery is not more than 4.2V, and the full charge voltage of a single cell of LiHV battery is not more than 4.35v).
Do not over-discharge (the single-cell discharge voltage of LIPO and LiHV batteries cannot be lower than 3.5V, over-discharging will damage the battery and cause swelling).
Don’t place the battery close to open flames or fire sources.Keep the battery away from flammable materials when chargingPlease carefully check the battery voltage and capacity before charging and useIt is forbidden to reverse the positive and negative poles of the battery (to avoid short circuit)
Do not directly touch the leaking battery. If you accidentally touch the electrolyte, please wash it with clean water immediately. If it is serious, please consult a doctor immediately.
Please dispose of the ruptured battery in time and do not reuse it
If you need to store the battery for a long time, please maintain the battery voltage at a single-cell 3.80V-3.85V. Please ensure that a charge-discharge activation is performed within 3 months to maintain the stability of the battery.
It is forbidden to disassemble and reassemble the battery or change the wiring (it is easy to cause short circuits and burning).
If a collision occurs during use, please remove the battery. Check carefully whether the battery and connector are normal.
Sub250's Nanofly16 1S frame is one of the lightest and most nimble carbon fiber frames out! Check out the Prop intended for this frame with matching color!!
Check out all our Micro Props, as well as the rest of our Sub250 selection!
Specifications
Weight: 0.24g
Propeller Diameter : 40mm
Shaft: 1.5mm
Pitch: 1 inch
Blades: 2
Material: Poly Carbonate
Hub Diameter:5mm
Hub Thickness: 5mm
Color: Aquamarine
Includes
2 x CW HQ 40mm Micro Whoop Props
2 x CCW HQ 40mm Micro Whoop Props
Sub250's Nanofly16 1S frame is one of the lightest and most nimble carbon fiber frames out! Check out the Prop intended for this frame with matching color!!
Check out the rest of our pre-built quads, as well as the rest of our Sub250 selection!
Specifications
Weight : 0.24g
Propeller Diameter : 40mm
Shaft: 1mm
Pitch: 1 inch
Blades: 2
Material: Poly Carbonate
Hub Diameter:5mm
Hub Thickness: 5mm
Color: Aquamarine
Includes
2 x CW HQ 40mm Micro Whoop Props
2 x CCW HQ 40mm Micro Whoop Props
Sub250's Nanofly16 1S frame is one of the lightest and most nimble carbon fiber frames out! Check out the motor intended for this frame with matching color!!
Check out our vast motor selection as well as the rest of our Sub250 selection!
Specifications
Input Voltage: 1S
Kv Rating: 19000Kv
Configuration: 9N12P
Shaft Diameter: 1.5mm
Weight (Incl. Cable): 2.2g
Mounting Pattern: 6x6mm TRI
Includes
1x Sub250 M1 0803 19000Kv Micro/Whoop Motor
Sub250's Nanofly16 1S frame is one of the lightest and most nimble carbon fiber frames out! Check out the motor intended for this frame with matching color!!
Check out our vast motor selection as well as the rest of our Sub250 selection!
Specifications
Input Voltage: 1S
Kv Rating: 19000Kv
Configuration: 9N12P
Shaft Diameter: 1.5mm
Weight (Incl. Cable): 2.2g
Mounting Pattern: 6x6mm TRI
Includes
4x Sub250 M1 0803 19000Kv Micro/Whoop Motor
Sub250's Nanofly16 1S frame is one of the lightest and most nimble carbon fiber frames! Featuring a true X layout and prints included, the Sub250 Nanofly16 is a go-to outdoor whoop frame!Check out the rest of our pre-built quads and the rest of our Sub250 selection!
Specifications
Brand Name: Sub250
Model: NF16
Wheelbase size: 77mm
Bottom plate thickness: 1.5mm
Camera plate thickness: 1.0mm
FC mounting holes: 25.5mm x 25.5mm
Motor mounting holes: 3-M1.4-EQS-Ø6.6
Propeller size: 40mm
Size:65mm x 65mm x 41mm
Weight: 8.3g (including 3D print)
Includes
1 x 1.5mm bottom plate
1 x 3D printed top cover
1 x 3D printed battery holder
16 x M1.4 x 3 round head Phillips screws
1 x M2 x 6mm round head screw
3 x M2 x 12 round head screws
1 x M2 x 14 round head screw
4 x M2 x 6.6 shock absorbers
8 x M2 x 2 nylon nuts
1 x 1.5mm L-shaped screwdriver
1 x Phillips screwdriver
The long-awaited second member of the Nanofly family "Nanofly20!" is released! "Change your flying habits in small spaces". The Nanofly20 is equipped with a two-inch propeller, and the motor mounting hole is 3-M1.4-Ø6.6, which can easily install most of the 1002 motors and 1102 motors on the market. Its overall lightweight design achieves a light feel, "as light as a swallow". The 25.5 flight controller holes can be installed with mainstream flight controllers on the market. Install a highly integrated sub 1s 5A flight controller, so that it can take off with only one flight controller board plus a camera and motor. It can also be used with Walksnail Avatar VTX and HDZero VTX.
Features
"Light as a swallow" lightweight design, with an overall weight of 8.4g, giving more installation space for your electronic equipment.
Carbon fiber bottom plate design, body strength pro beyond.
25.5mm flight controller installation holes allow for easy installation of the market's most popular AIO flight controllers.
Ø6.6 M1.4-3 motor mounting holes, compatible with most motors such as 0803, 1002, and 1102.
Match a variety of VTX solutions to build your own HD FPV mini drone.
Specifications
Item: Nanofly20 frame
Wheelbase: 88mm
Arm plate: 1.5mm
Motor holes: 3-M1.4-EQS-Ø6.6
FC mounting holes: 25.5x25.5
Camera installation space: 14x14 (mm)
Weight: 8.4g
Includes
1x Nanofly20 Frame 1x Battery cabin4x M2x18 Round head screw4x M2x12 Round head screw2x M2x3 Round head screw2x M1.4x3 Round head cross screw
The Sub250 Whoopfly16 BNF is an ultra-light analog 1S mini Whoop designed for a smooth indoor flying experience. It features an inverted pusher FPV drone layout, a one-piece injection-molded protective ring frame, and a short wheelbase to provide maximum safety and protection. Powered by a popular 1002 motor, this reliable drone delivers a strong and effortless user experience. Whoopfly16 can adapt to mainstream 1S image transmission (analog / HD Zero / AVATAR).. The analog video transmission will be equipped with an Ant eco lens from Caddx, and the elevation angle of the lens can be adjusted upwards by 30 degrees. With the latest 1s 530mah battery, the battery life can reach 4 minutes and 30 seconds.
Make sure to check out all of our Analog BNF quads as well as the rest of our Sub250 selection!
Features
Inverted whoop FPV drone makes the paddle and motor more efficient.
With the new 1S 530mah LiHV battery
Highly integrated flight control, integrated flight control, ESC, remote control receiver, and video transmission.
One-piece injection molded protective ring frame, higher strength, and less deformation of the frame during aggressive flight.
The protection of the circle is enhanced, and novices and experienced pilots both are safe.
There are many options for image transmission, you can choose HD Zero /AVATAR and analog image transmission
Use 1002 21000kv motor, abundant power "always ready to overtake"
Indoor flight is safer with a small wheelbase and a protective ring, and it is handier to fly with a reasonable combination.
Suitable for beginner outdoor advanced racing practice
Specification
Analog Version
Product name: Whoopfly16
Frame: WF16
Wheelbase size: 75mm
Flight control system: Redfox A1
MCU: STMF411
IMU: ICM42688-P
OSD: BetaFlight OSD w/AT7456E chip
ESC: Redfox A1 4IN1 5A ESC
VTX: VTX 5.8G 200mW
Lens: Caddx Ant eco
Propeller: Gemfan 1608-3
Antenna: 5.8g copper tube antenna 70mm
weight: 37.7g
Receiver: ELRS (SPI)
Includes
1x Sub250 Whoopfly16 BNF 1.6" Analog Ultra-Light 1S Whoop - ELRS 2.4GHz (SPI)
4x M1.4 cross screws
1x Blue frame protection cotton
1x Red frame protective cotton
1x L-shaped inner hexagon screw blade
1x Cross screw blade
2x 3M double-sided tape
4x 1608-3 propellers
The Sub250 Whoopfly16 BNF is an ultra-light 1S mini Whoop designed for a smooth indoor flying experience. It features an inverted pusher FPV drone layout, a one-piece injection-molded protective ring frame, and a short wheelbase to provide maximum safety and protection. Powered by a popular 1002 motor, this reliable drone delivers a strong and effortless user experience. Whoopfly16 can adapt to mainstream 1S image transmission (analog / HD Zero / AVATAR). The analog video transmission will be equipped with an Ant eco lens from Caddx, and the elevation angle of the lens can be adjusted upwards by 30 degrees. With the latest 1s 530mah battery, the battery life can reach 4 minutes and 30 seconds.
Make sure to check out all of our HDzero BNF quads as well as the rest of our Sub250 selection!
Features
Inverted whoop FPV drone makes the paddle and motor more efficient.
With the new 1S 530mah LiHV battery
Highly integrated flight control, integrated flight control, ESC, remote control receiver, and video transmission.
One-piece injection molded protective ring frame, higher strength, and less deformation of the frame during aggressive flight.
The protection of the circle is enhanced, and novices and experienced pilots both are safe.
There are many options for image transmission, you can choose HD Zero /AVATAR and analog image transmission
Use 1002 21000kv motor, abundant power "always ready to overtake"
Indoor flight is safer with a small wheelbase and a protective ring, and it is handier to fly with a reasonable combination.
Suitable for beginner outdoor advanced racing practice
Specification
HD Zero Version
Product name: Whoopfly16
Frame: WF16
Wheelbase size: 75mm
Flight control system: Redfox A1
MCU: STMF411
IMU: ICM42688-P
OSD: BetaFlight OSD w/AT7456E chip
ESC: Redfox A1 4IN1 5A ESC
VTX: Hd Zero whoop lite
Lens: Hd Zero nano lite camera
Propeller: Gemfan 1608-3
Antenna: 5.8g copper tube antenna 70mm
weight: 39.2g
Receiver: ELRS (SPI)
Includes
1x Sub250 Whoopfly16 BNF 1.6" HD Ultra-Light HDzero 1S Whoop - ELRS 2.4GHz (SPI)
4x M1.4 cross screws
1x Blue frame protection cotton
1x Red frame protective cotton
1x L-shaped inner hexagon screw blade
1x Cross screw blade
2x 3M double-sided tape
4x 1608-3 propellers
Introducing a new 1S AIO from T-Motor which is perfect for small whoops and toothpick quads! Featuring full BLHeli_32 ESC Firmware which gives you access to features like bidirectional DShot for RPM filtering and up to 96KHz PWM frequency for increased flight time and motor smoothness. The AIO also is equipped with 16MB of blackbox memory and the latest BMI270 gyro so you can tune your quad to perfection. Pick up yours today!
Browse our whoop flight controllers, and all our T-Motor products!
Features
Support 1S battery
F411 chip is used with high-performance computing speed, making it smoother during flight.
Specifications
Whoop AIO F4 V1.1 AIO
MCU: STM32F411
IMU: BMI270
Firmware target: STM32F411
OSD: Betaflight OSD w/ AT7456Ev
UART Ports: R1 T1,R2 T2
USB: Micro USB
BEC output: 5V@1A
Continuous current: 6A
Input: 1S
Blackbox: 16Mb
Supports: Dshot300, Dshot600
ESC Firmware: BLHeli_32
PWM Frequency: 24-96KHz
Size: 29.5x29.5mm Board
Installing Hole: 25.5x25.5mm, M2
Weight: 5.7g
Includes
T-Motor F411 1S Toothpick/Whoop AIO w/ 13A ESC
An awesome little AIO from T-Motor, Coming with 6A ESCs, ELRS 2.4G onboard reciever, and a 50mw VTX with OSD! This whoop AIO board truly does it all!
Browse our whoop flight controllers, and all our T-Motor products!
Features
Support 1S battery
F411 chip is used with high-performance computing speed, making it smoother during flight.
ELRS on board
50Mw VTX Smart Audio 1.0
Specifications
Whoop AIO F4 V1.1 AIO
MCU: STM32F411
IMU: BMI270
Firmware target: STM32F411
OSD: Betaflight OSD w/ AT7456Ev
UART Ports: R2 T2
USB: Micro USB
BEC output: 5V@1A
Continuous current: 6A
Input: 1S
Supports: Blue Jay
Size: 29.5x29.5mm Board
Installing Hole: 25.5x25.5mm, M2
Weight: 6.7g
Includes
T-Motor F411 1S Toothpick/Whoop AIO w/ BlueJay 6A ESC & ELRS RX
