103076-4, Spartan SR 6S (Self Righting) 36" Brushless Boat (Optional Trailer Available)
36″ Reinforced Deep-V Hull
Made from lightweight vacuum-formed ABS
Self-righting flood chamber
Pre-applied graphics
Quick-release electronics tray
Rigid Injection-Molded Clipless Hatch
Four quick-release hatch nuts with tool
Foam seal keeps water out
Includes optional tool-free wingnuts
Up to 50 MPH with Dual 3s LiPo Batteries
VXL-6s™ Marine Electronic Speed Control
Water-cooled case
Three drive profiles
Sport Mode - forward / brake / reverse
Race Mode - forward / brake
Training Mode™ - 50% forward / brake / 50% reverse (patented)
Built-in two-stage low-voltage detection for LiPo batteries
NiMH battery packs: 14 cells (16.8 volts)
LiPo battery packs: 4-6 cells (14.8 to 22.2 volts)
Velineon 540XL Brushless Motor
Ultra high-temperature sintered Neodymium magnets
Efficient, high-speed ball bearings
1800 kV
5 mm output shaft
Water-cooled jacket
Traxxas Stability Management (TSM)
Improves straight line acceleration
Never dulls throttle or slows the vehicle
Adjusts from off to 100% assistance from the transmitter
TQi 2.4 GHz Radio System
2-channel transmitter
5-channel micro receiver (6533) with fail-safe security and integrated telemetry ports
Automatically stores and loads settings for up to 30 Traxxas Link enabled models
Programmable multi-function knob
Patented waterproof receiver box
Extra-Long 218 mm Battery Tray
Centralizes battery weight
Allows fore and aft battery positioning
Accommodates multiple battery configurations
Secure hook and loop straps
Driveline
Heavy duty 4.7 mm diameter flex shaft
Quick-release motor collet
Blue-anodized aluminum drive strut
Low-maintenance bushings
High performance prop
Steering
Waterproof digital 2056 servo
Blue-anodized aluminum rudder with water pickup
Precision-Cut Stainless Steel Trim Tabs and Turn Fins
Stainless Steel Hex Hardware Used Throughout
This product was added to our catalog on March 14, 2024
38104-1, Traxxas Blast 24" High Performance RTR Race Boat w/TQ 2.4GHz Radio, Battery & DC Charger
The Traxxas Blast 24" High Performance RTR Race Boat is a fast, reliable and easy to drive boat. With a waterproof servo and a watertight receiver box, this is a perfect boat for lakes and larger pools. Traxxas has provided a updated set of graphics and a powerful water cooled brushed motor to provide killer looks and performance.
A TQ 2-channel 2.4GHz radio system is used so that multiple boats can be used side by side with no interference. The TQ uses advanced programming that provides long range control with glitch free performance.
Features:
TQ™ 2.4GHz radio system
7.2V Power Cell™ NiMH battery
4-amp DC Peak Detecting Fast Charger
Installed water cooling system
Waterproof electronics
Sealed receiver box
Nautica™ waterproof electronic speed control
High-torque waterproof servo
Factory-applied decals
Traxxas High-Current Connector
Sleek styling
Specifications:
Hull Type: High performance modified "V"
Dead Rise Angle: 20 degrees
Hull Length: 23.75 inches (603 mm)
Beam: 5.75 inches (146 mm)
Weight: 28 ounces (.793 kg)
Draft: 3.25 inches (83 mm)
Speed Control Type: Nautica™ waterproof ESC
Charger: 4-amp DC fast charger
Battery: Traxxas 6-cell NiMH battery with iD
Motor (electric): Water-cooled 540 Stinger (20-turn)
Drive System: Direct drive
Outdrive: Adjustable surface-piercing
Radio System: Traxxas TQ 2.4GHz (3-channel)
Skill Level: 1
Includes:
(1) Orange Blast 24" RTR Boat
(1) Traxxas TQ 2.4GHz (3-channel)
(1) 4-Amp DC Fast Charger
(1) 7.2V NiMH battery with iD Connector
Needed to Complete:
(4) AA Batteries for Transmitter
This product was added to our catalog on May 7, 2021
57046-4, Traxxas DCB M41 Widebody 40" Catamaran High Performance 6S Race Boat w/TQi 2.4Ghz Radio & TSM
Traxxas DCB M41 Widebody 40" Catamaran - Extreme Power with the Style to Match!
The Traxxas DCB M41 Widebody 40" Catamaran was built for extreme power and speed. With a powerful 6s motor this boat can reach speeds in excess of 50mph! Built with a Twin-hull catamaran design the DCB M41 can handle high speeds even in less than ideal conditions. Additionally this boat is equipped with Traxxas Stability Management (TSM) bringing another level to stability that other boats cannot match. With 6s power, off the charts stability and dependable Traxxas components leave your competition at the docks with the DCB M41 Widebody!
Traxxas has faithfully captured the incredible looks and performance of the DCB M41 in a detailed scale replica that is versatile, fun, and fast. Designed by DCB (Dave’s Custom Boats) founder Dave Hemmingson, is one of the largest full size models offered in the DCB M-Series. The full size boat with its precision sculpted design and a pair of Mercury Racing 1350 engines speeds across the water at 175mph!
Features:
50+mph on 6S LiPo
40" DCB M41 Widebody catamaran replica
Stable Twin-hull catamaran performs across waves and smooth water
Water-cooled, waterproof VXL-6s Marine speed control
Traxxas High-Current Connectors (patented)
Velineon 540XL high-output brushless motor with high flow water-cooling jacket
Quick-release Power Module integrates power system with waterproof electronics
Adjustable battery trays with hook-and-loop straps
Blue-anodized aluminum rudder support, rudder, and drive strut
Stainless steel trim tabs, and hardware
TQi 2.4GHz radio system and 5-channel receiver
Access the Traxxas Link app with the Traxxas Link Wireless Module (#6511) (sold separately)
Traxxas Stability Management® (TSM) makes it easy to go fast
Waterproof high-torque steering servo
Specifications:
Hull Type: Vacu-formed ABS, catamaran, shoebox style
Hull Length: 39.5" (1003mm)
Overall Length: 40.6" (1030mm)
Beam: 10.5" (267mm)
Height: 5.95" (151mm)
Deadrise & Transom: 14.5 degrees
Weight: 86.7 ounces (2.46 kg)
Speed Control Type: Traxxas Velineon VXL-6s, water-cooled
Input Voltage: 2-6 LiPo cells (14.8-22.2 volts DC)
BEC Voltage: 6.0 VDC
BEC Current: 3A
Thermal Protection: Thermal shutdown
Low Voltage Detection: Yes (user enabled)
Motor (electric): Traxxas Velineon 540XL Brushless, water-cooled
Drive System: Direct drive, 0.15 inch flex cable
Outdrive: Adjustable aluminum
Prop: 2-blade composite, 42x59mm
Transmitter: TQi 2.4GHz (2-channel)
Receiver: 6533 2.4GHz Traxxas Stability Management 5-channel
Servo: 2056 High-torque waterproof
Skill Level: 2
Needed To Complete:
(4) "AA" Batteries (for transmitter)
(2) 2S or 3S LiPo Battery w/iD Connector
(1) Compatible Battery Charger
This product was added to our catalog on May 1, 2022
ARA2102, Arrma Granite Grom MEGA 4WD 380 Brushed 1/18 Monster Truck RTR w/SLT2 2.4GHz Radio, Battery & Charger
The GRANITE GROM 4X4 Monster Truck upholds the same rigorous engineering standards as its larger ARRMA RC counterparts. Additionally, it features a clipless body mount design that ensures the body remains securely attached while remaining effortlessly removable for drivers of all ages. In the realm of small-scale RC basher models, it stands out as a leader, offering a unique blend of convenience, power, strength, and exceptional handling capabilities that enable you to take your stunts to the next level.
The ARRMA GRANITE GROM 4X4 Monster Truck is built to withstand any challenge you throw its way. Its impact-absorbing front and rear bumpers are ready for intense bashing, flanking a robust composite chassis. Power is efficiently transmitted through a robust 4WD drivetrain with durable metal gears, connecting the MEGA 380 brushed motor to the rugged dBoots FORTRESS monster truck wheels and tires. The Spektrum SX110 steering servo boasts waterproof construction and dependable metal gear strength.
Features:
Awesome monster truck styling with three rad color options
fast and easy body attachment and removal mounts
High strength metal gear drivetrain
Fully enclosed drivetrain for tertian versatility
High strength composite chassis
Ballistic 4WD drive train
Powerful 2S LiPo fun
Waterproof 25Amp Spektrum SLT 2-in1 ESC and receiver
Waterproof Spektrum SX110 metal geared servo
Spektrum SLT 2-channel 2.4GHz radio
Specifications:
Scale: 1/18
Length: 9.84in (249.9mm)
Width: 7.87in (199.8mm)
Height: 4.65in (118.1mm)
Wheelbase: 6.5in (165.1mm)
Weight: 28.2oz (800g)
Drive: 4WD
Power Source: Electric
Assembly Level: RTR
Includes:
(1) 1/18 Arrma Granite Grom
(1) 7.4V 1400mAh 2S LiPo Battery with IC2 connector
(1) Spektrum S10 Smart G2 Mini 2S USB-C Charger
Needed to Complete:
(1) USB power adapter with QC 2.0/3.0 18W+
This product was added to our catalog on October 27, 2023
ARA2106, Arrma Typhon Grom MEGA 4WD 380 Brushed 1/18 Buggy RTR w/SLT2 2.4GHz Radio, Battery & Charger
This product was added to our catalog on March 27, 2024
ARA3230SKT1, Arrma Gorgon 4X2 MEGA 550 Brushed 1/10 Monster Truck Ready-To-Assemble Kit w/SLT2 2.4GHz Radio, Battery & Charger
The GORGON 4X2 MEGA 550 Brushed 1/10 Monster Truck RTA (Ready-To-Assemble) is a powerhouse of a machine, renowned for its exceptional durability. Its robust brushless-ready drive train ensures high performance and longevity, making it a top choice for RC enthusiasts seeking both power and resilience. The truck boasts a Strong Spine Composite Chassis, providing unmatched structural integrity while withstanding the harshest terrains and stunts. Moreover, its hidden body mounting system not only enhances its aesthetics but also preserves the truck's stunning appearance throughout your thrilling off-road adventures. This variant of the Gorgon provides you with the satisfaction of building the kit yourself and understanding the fun of driving and breaking a kit that you put together.
In addition to its remarkable durability and structural strength, the GORGON Monster Truck comes packed with high-quality, LiPo-compatible Spektrum electronics, ensuring precision control and optimal power management. It's equipped with a Spektrum S660 waterproof digital steering servo, guaranteeing precise and responsive handling even in challenging conditions. The inclusion of the Spektrum waterproof SLT 2-in-1 ESC/receiver unit enhances the truck's resilience, making it a formidable performer in wet and muddy environments. With the Spektrum SLT2 2-channel 2.4GHz transmitter in hand, you'll experience a secure and uninterrupted connection, allowing you to push the GORGON's capabilities to the max while maintaining complete control.
Features
Build it yourself RTA (Ready-To-Assemble)
Build the kit in an hour or less
Durable, brushless ready drive line
Strong Spine Composite Chassis
Tough Brushless ready Transmission
Hidden body mounting to preserve the awesome looks
Bottom-loading battery tray for easy battery changes
Full ball bearings throughout
High-quality, LiPo-compatible Spektrum electronics
Spektrum S660 waterproof digital steering servo
Spektrum waterproof SLT 2-in-1 ESC/receiver unit
Spektrum SLT2 2-channel 2.4GHz transmitter
Spektrum 8.4V 3300mAh 7-Cell Smart NiMH Battery with IC3 Connector
Spektrum 2S LiPo Ready S120 USB-C Smart Charger
Specifications
Scale: 1/10
Drivetrain: 2WD
Power Source: Electric
Vehicle Type: Monster Truck
Product Length: 16.57in (421mm)
Product Width: 13.15in (334mm)
Product Height: 9.65in (245mm)
Wheelbase: 11.61in (295mm)
Product Weight: 5.95lb (2.7kg)
Body: Pre-painted
Assembly: RTA
Includes
(1) GORGON 4X2 MEGA 550 Brushed 1/10 Monster Truck RTA
(1) Spektrum 8.4V 3300mAh 7-Cell Smart NiMH Battery with IC3 Connector
(1) Spektrum 2S LiPo Ready S120 USB-C Smart Charger
(4) AA Batteries
Needed to Complete
(1) USB Power Adaptor with QC2.0/3.0 18W
This product was added to our catalog on August 5, 2024
ARA3230ST1, Arrma Gorgon 4X2 MEGA 550 Brushed 1/10 Monster Truck RTR w/SLT2 2.4GHz Radio, Battery & Charger
Arrma 1/10 2WD GORGON Electric Monster Truck
The GORGON 4X2 MEGA 550 Brushed 1/10 Monster Truck RTR is a powerhouse of a machine, renowned for its exceptional durability. Its robust brushless-ready drive train ensures high performance and longevity, making it a top choice for RC enthusiasts seeking both power and resilience. The truck boasts a Strong Spine Composite Chassis, providing unmatched structural integrity while withstanding the harshest terrains and stunts. Moreover, its hidden body mounting system not only enhances its aesthetics but also preserves the truck's stunning appearance throughout your thrilling off-road adventures.
In addition to its remarkable durability and structural strength, the GORGON Monster Truck comes packed with high-quality, LiPo-compatible Spektrum electronics, ensuring precision control and optimal power management. It's equipped with a Spektrum S660 waterproof digital steering servo, guaranteeing precise and responsive handling even in challenging conditions. The inclusion of the Spektrum waterproof SLT 2-in-1 ESC/receiver unit enhances the truck's resilience, making it a formidable performer in wet and muddy environments. With the Spektrum SLT2 2-channel 2.4GHz transmitter in hand, you'll experience a secure and uninterrupted connection, allowing you to push the GORGON's capabilities to the max while maintaining complete control.
Features
Factory-built and ready-to-run
Durable, brushless ready drive line
Strong Spine Composite Chassis
Tough Brushless ready Transmission
Hidden body mounting to preserve the awesome looks
Bottom-loading battery tray for easy battery changes
Full ball bearings throughout
High-quality, LiPo-compatible Spektrum electronics
Spektrum S660 waterproof digital steering servo
Spektrum waterproof SLT 2-in-1 ESC/receiver unit
Spektrum SLT2 2-channel 2.4GHz transmitter
Spektrum 8.4V 3300mAh 7-Cell Smart NiMH Battery with IC3 Connector
Spektrum 2S LiPo Ready S120 USB-C Smart Charger
Specifications
Scale: 1/10
Drivetrain: 2WD
Power Source: Electric
Vehicle Type: Monster Truck
Product Length: 16.57in (421mm)
Product Width: 13.15in (334mm)
Product Height: 9.65in (245mm)
Wheelbase: 11.61in (295mm)
Product Weight: 5.95lb (2.7kg)
Body: Pre-painted
Assembly: RTR
Includes
(1) GORGON 4X2 MEGA 550 Brushed 1/10 Monster Truck RTR
(1) Spektrum 8.4V 3300mAh 7-Cell Smart NiMH Battery with IC3 Connector
(1) Spektrum 2S LiPo Ready S120 USB-C Smart Charger
(4) AA Batteries
Needed to Complete
(1) USB Power Adaptor with QC2.0/3.0 18W
This product was added to our catalog on October 4, 2023
ARA3230T1, Arrma Gorgon 4X2 MEGA 550 Brushed 1/10 Monster Truck RTR w/SLT2 2.4GHz Radio
Arrma 1/10 2WD GORGON Electric Monster Truck
The GORGON 4X2 MEGA 550 Brushed 1/10 Monster Truck RTR is a powerhouse of a machine, renowned for its exceptional durability. Its robust brushless-ready drive train ensures high performance and longevity, making it a top choice for RC enthusiasts seeking both power and resilience. The truck boasts a Strong Spine Composite Chassis, providing unmatched structural integrity while withstanding the harshest terrains and stunts. Moreover, its hidden body mounting system not only enhances its aesthetics but also preserves the truck's stunning appearance throughout your thrilling off-road adventures.
In addition to its remarkable durability and structural strength, the GORGON Monster Truck comes packed with high-quality, LiPo-compatible Spektrum electronics, ensuring precision control and optimal power management. It's equipped with a Spektrum S660 waterproof digital steering servo, guaranteeing precise and responsive handling even in challenging conditions. The inclusion of the Spektrum waterproof SLT 2-in-1 ESC/receiver unit enhances the truck's resilience, making it a formidable performer in wet and muddy environments. With the Spektrum SLT2 2-channel 2.4GHz transmitter in hand, you'll experience a secure and uninterrupted connection, allowing you to push the GORGON's capabilities to the max while maintaining complete control.
Features
Factory-built and ready-to-run
Durable, brushless ready drive line
Strong Spine Composite Chassis
Tough Brushless ready Transmission
Hidden body mounting to preserve the awesome looks
Bottom-loading battery tray for easy battery changes
Full ball bearings throughout
High-quality, LiPo-compatible Spektrum electronics
Spektrum S660 waterproof digital steering servo
Spektrum waterproof SLT 2-in-1 ESC/receiver unit
Spektrum SLT2 2-channel 2.4GHz transmitter
Specifications
Scale: 1/10
Drivetrain: 2WD
Power Source: Electric
Vehicle Type: Monster Truck
Product Length: 16.57in (421mm)
Product Width: 13.15in (334mm)
Product Height: 9.65in (245mm)
Wheelbase: 11.61in (295mm)
Product Weight: 5.95lb (2.7kg)
Body: Pre-painted
Assembly: RTR
Includes
(1) GORGON 4X2 MEGA 550 Brushed 1/10 Monster Truck RTR
(4) AA Batteries
Needed to Complete
(1) 7-Cell NiMH or 2S LiPo battery with IC3/EC3 Connector
(1) Compatible Charger
This product was added to our catalog on October 4, 2023
ARA4202V3, Arrma Granite 4x4 V3 550 Mega RTR Monster Truck (Red) w/Spektrum SLT3 2.4GHz Radio
The Arrma Granite 2S 4x4 V3 550 Mega RTR Monster Truck comes out of the box ready to bash in any terrain. This version features equipment that further increases the original monster truck’s already impressive performance and durability.
The GRANITE 4X4 MEGA RTR Monster Truck is DESIGNED FAST, DESIGNED TOUGH — built for exciting bashing speeds and extreme, all-terrain durability. Features to enhance its unstoppable performance include a stronger chassis and retained hinge pin plates; steering with more clearance for stones; a castellated slipper pad and sliding gear mesh; and rubber shielded bearings throughout.
The monster truck now also includes the Spektrum SLT3 transmitter and SLR300 receiver. The transmitter is ergonomically designed for long periods of fatigue-free bashing and has a foam wheel for precise fingertip control plus an improved hand grip and trigger feel. New bashers will be able to set throttle limits at 50% or 75% until they are ready to use the full speed potential. The SLT3 is compatible with Tactic SLT receivers to run other RTR vehicles you may own, and includes a third channel to control optional features such as lights and winches on models that have them.
It retains the ingenious modular design perfected by ARRMA engineers for easy component access and maintenance. The power module, with improved dirt management, consists of a MEGA 550 motor, motor plate, slipper clutch assembly and gear cover. The power module can be detached from the chassis as a complete unit by removing just one screw. With the power module removed, the slipper clutch can be reached easily for adjustments by taking out three screws that attach the gear cover. The gear ratio can be finely tuned as the power module now uses a sliding motor mesh design.
A two-piece molding screwed to the truck’s chassis serves as its electronics module, containing a waterproof receiver box, servo mount and ESC tray. The SLR300 receiver mounts inside the receiver box for protection from dirt and moisture. The ultra-compact ESC is screwed to the top of the module, allowing quick access to the on/off switch, while the servo mounts to the side. All three components can be removed together, quickly and easily.
The differential module houses each differential unit in an innovative yoke design. Only eight screws need to be removed to release the front and rear yokes. The power module can then be detached, allowing you to pivot the gearbox cases for differential access. The GRANITE 4X4 MEGA RTR comes brushless-ready with 37T 1.35mod diffs with silicone O-rings. The large gears can withstand huge torque, and internal metal gears have been chosen for reliability during extreme bashing.
Its full-time 4WD transmission uses strong front, rear, and centerline telescopic driveshafts that can’t be lost during heavy impacts, unlike dogbones. A simple, dependable, responsive steering assembly complements the ultra-reliable drive system and features a servo horn with built-in servo saver. The GRANITE 4X4 MEGA RTR includes the waterproof Spektrum SPMS650 digital servo for 20% more torque than the previous version’s ADS-5 servo.
The self-bleeding, oil-filled shocks, now with silicone O-rings, use a tried and tested, coil-over design for simple maintenance and amazing handling. Their innovative rod-end has a molded-in spring perch for extra toughness. High chassis guards limit the amount of dirt and debris that can get into the chassis tub. Shock-absorbing loops keep the front and rear bumpers secured to the chassis, offering defense against heavy impacts.
Tough, multi-spoke black MT wheels with dBoots Fortress MT tires give the GRANITE 4X4 MEGA RTR effective traction for bashing on almost any terrain. Multiple battery types can be used with the hook-and-loop mounting, from 6-cell NiMH packs to a 2S block pack. This version comes with a Dynamite 3300 mAh 8.4V 7-cell Speedpack 2 Hump NiMH battery that provides 35% more run time compared to the 2400mAh pack of its predecessor.
Features:
Stronger chassis and retained hinge pin plates
Steering with more clearance for stones
Castellated slipper pad and sliding gear mesh
23T Spline servo saver
Brushless-ready 37T 1.35Mod diffs with silicone O-rings
Power Module with sliding gear mesh and improved dirt management
Rubber shielded bearings throughout
Oil-filled shocks with silicone O-rings
New body design, front and rear bumpers, paint and decals
New vented tires
MEGA 12T brushed 550 motor
MEGA waterproof* ESC
IC3™ connectors (EC3™) compatible
Signature easy-access modular design
Easy-access power module
Easy-access electronics module
Easy-access diff module removal front and rear
Double wishbone suspension front and rear
Metal-geared differentials
Adjustable ride height
Adjustable body mounts
Extended height dirt defenders
Multi-terrain dBoots® Fortress™ MT tires
Tough multi-spoke black MT wheels
ADC-N7 7-cell NiMH wall charger
2-year limited warranty (see website for details)
30MPH (48km/h) speed achievable in optimum driving conditions with optional gearing
Specifications:
Ball Bearings: Transmission
Battery: Included
Body: Painted, decalled and trimmed
Charger: Included
Chassis: Molded Composite
Completion Level: Ready-To-Run
Differential: 2 Gear Diffs
Drivetrain: 4WD
Final Drive Ratio: 18.5
Front Track: 13.46 in (342mm)
Power Type: Electric
Gear Pitch: 48-pitch
Ground Clearance: 1.85 in (47mm)
Internal Gear Ratio: 2.85
Motor Type: Brushed
Pinion: 14T
Product Height: 8.11" (206 mm)
Product Length: 17.76" (451 mm)
Product Weight: 6.69lbs (3035g)
Product Width: 13.46" (342 mm)
Radio: Included
Rear Track: 13.46 in (342mm)
Receiver: Included
Scale: 1/10
Servos: Included
Shock Type: Oil-Filled, Coil-Over Springs
Spur Gear: 91T
Suspension: Independent
Track: 13.46 in (342mm)
Vehicle Type: Monster Truck
Water-Resistant: Yes
Wheelbase: 11.3 in (287mm)
Includes:
(1) ARRMA® GRANITE™ 4X4 MEGA 550 1/10 Scale 4WD Electric Monster Truck RTR
(1) MEGA Waterproof* ESC
(1) MEGA 12T Brushed 550 Motor
(1) Spektrum™ 2.4GHz SLT3™ 3-Channel Transmitter
(1) Spektrum™ SLR300 Receiver
(1) Spektrum™ Waterproof* SPMS650 Digital Servo
(1) Dynamite® 3300mAh 8.4V 7-Cell Speedpack® 2 Hump NiMH Battery
(1) ADC-N7 7-Cell NiMH Wall Charger
(1) Product Manual
Needed to Complete:
(4) AA Batteries
This product was added to our catalog on August 26, 2021
ARA4302V3, Arrma Granite 4X4 V3 3S BLX 1/10 RTR Brushless 4WD Monster Truck w/Spektrum SLT3 2.4GHz Radio
The Arrma 1/10 Granite 4X4 V3 3S BLX Brushless 4WD Monster Truck delivers jaw-dropping power and 50+ MPH brushless performance. Precision aluminum, tough steel and composite materials come together for an easy-to-maintain, super-durable vehicle design that’s now upgraded for even greater performance and durability.
The GRANITE 4X4 3S BLX RTR is DESIGNED FAST, DESIGNED TOUGH — built for exciting bashing speeds and extreme, all-terrain toughness. Features that enhance its unstoppable performance include a stronger chassis and retained hinge pin plates; steering with more clearance for stones; a castellated slipper pad and sliding gear mesh; and rubber-shielded bearings throughout.
It also now includes a Spektrum SLT3 transmitter and SLR300 receiver. The transmitter is ergonomically designed for long periods of fatigue-free bashing and has a foam wheel for precise fingertip control, plus an improved hand grip and trigger feel. New drivers will be able to set throttle limits at 50% or 75% until they are ready to use the full speed potential. The SLT3 is compatible with Tactic SLT receivers to run other RTR vehicles you may own, and includes a third channel to control optional features such as lights and winches on models that have them.
ARRMA now powers the GRANITE 4X4 3S BLX with a brushless system featuring its BLX100 ESC and the Spektrum Firma 3200Kv brushless motor. The combination provides incredible torque, acceleration and speed. The transmission and chassis are ruggedly engineered to take full advantage of the electronics’ power.
It has the ingenious modular design perfected by ARRMA engineers for easy component access and maintenance. The power module, with improved dirt management, consists of the motor with ARRMA heatsink and cooling fan, plus motor plate, slipper clutch assembly and gear cover. The power module can be detached from the chassis as a complete unit by removing just one screw. With the power module removed, the slipper clutch can be reached easily for adjustments by taking out three screws that attach the gear cover. The gear ratio can be finely tuned as the power module now uses a sliding motor mesh design.
A two-piece molding screwed to the truck’s chassis serves as its electronics module, containing a waterproof receiver box, servo mount and ESC tray. The SLR300 receiver mounts inside the receiver box for protection from dirt and moisture. The ultra-compact ESC is screwed to the top of the module, allowing quick access to the on/off switch, while the servo mounts to the side. All three components can be removed together, quickly and easily.
The differential module houses each differential unit in an innovative yoke design. Only eight screws need to be removed to release the front and rear yokes. The power module can then be detached, allowing you to pivot the gearbox cases for differential access. The GRANITE 4X4 3S BLX RTR comes brushless-ready with 37T 1.35mod diffs with silicone O-rings. The large gears can withstand huge torque, and internal metal gears have been chosen for reliability during extreme bashing.
Its full-time 4WD transmission uses strong front, rear, and centerline telescopic driveshafts that can’t be lost during heavy impacts, unlike dogbones. A simple, dependable, responsive steering assembly complements the ultra-reliable drive system and features a servo horn with built-in servo saver. The GRANITE 4X4 3S BLX RTR includes the waterproof Spektrum SPMS651 metal-geared digital servo for 15% more torque than the previous version’s ADS-7M servo.
The self-bleeding, oil-filled shocks, now with silicone O-rings, use a tried and tested, coil-over design for simple maintenance and amazing handling. Their innovative rod-end has a molded-in spring perch for extra toughness. Extended height dirt defenders and a close-fitting body limit the amount of dirt and debris that can get into the chassis tub. Front and rear bumpers offer defense against impacts.
Four dBoots Fortress MT tires on gunmetal multi-spoke wheels give the GRANITE 4X4 3S BLX superb bite on a multitude of surfaces. ARRMA has also installed a wheelie bar as standard. The aggressively styled truck body looks great while bashing and even better up-close and personal, with great attention to detail on the decal and body aesthetics. Choose green or red trim schemes.
Features:
Stronger chassis and retained hinge pin plates
Steering with more clearance for stones
Castellated slipper pad and sliding gear mesh
Plastic locknut for slipper
23T Spline servo saver
37T 1.35Mod diffs with silicone O-rings
Power Module with sliding gear mesh and improved dirt management
Rubber shielded bearings throughout
Oil-filled shocks with silicone O-rings
Front and rear bumpers
Tough gunmetal colored multi-spoke wheels
Vented multi-terrain dBoots® Fortress™ MT tires
BLX100 2S/3S waterproof* ESC *For details on waterproof standards, refer to the instruction manual.
IC5™ connectors (EC5™) compatible
Signature easy-access modular design
Easy-access power module
Easy-access electronics module
Easy-access diff module removal front and rear
Double wishbone suspension front and rear
Metal-geared differentials
Extended height dirt defenders
Adjustable ride height
Adjustable body mounts
Adjustable turnbuckles
High-speed center driveshaft support
Wheelie bar
2-year limited warranty (see website for details)
50+ MPH (80+ km/h) speed achievable in optimum driving conditions on 3S LiPo
Specifications:
Ball Bearings: Full Ball Bearing Drivetrain
Battery: Sold Separately
Body: Painted, decalled and trimmed
Charger: Sold Separately
Chassis: Molded Composite
Completion Level: Ready-To-Run
Differential: 2 Gear Diffs
Drivetrain: 4WD
Final Drive Ratio: 10.83
Front Track: 13.46 in (342mm)
Power Type: Electric
Gear Pitch: 0.8MOD
Ground Clearance: 1.85 in (47mm)
Internal Gear Ratio: 2.85
Motor Type: Brushless - Sensorless
Pinion: 15T
Product Height: 8.11" (206 mm)
Product Length: 18.74" (476 mm)
Product Weight: 6.23lbs (2826g)
Product Width: 13.46" (342 mm)
Radio: Included
Rear Track: 13.46 in (342mm)
Receiver: Included
Scale: 1/10
Servos: Included
Shock Type: Oil-Filled, Coil-Over Springs
Speed Control: Included
Spur Gear: 57T
Suspension: Independent
Vehicle Type: Monster Truck
Water-Resistant: Yes
Wheelbase: 11.3 in (287mm)
Includes:
(1) ARRMA® GRANITE™ 4X4 3S BLX 1/10 Scale 4WD Electric Monster Truck RTR
(1) BLX100 2S/3S Waterproof* ESC
(1) Spektrum™ Firma™ 3660 3200Kv Brushless Motor
(1) Spektrum™ 2.4GHz SLT3™ 3-Channel Transmitter
(1) Spektrum™ SLR300 Receiver
(1) Spektrum™ SPMS651 Waterproof* Metal-Geared Digital Servo
(1) Product Manual
*NOTE: For details on waterproof standards, refer to the instruction manual.
Needed to Complete:
2S LiPo or 3S Hardcase LiPo Battery
Compatible Charger
LiPo Safe Charging Bag
(4) AA Batteries
This product was added to our catalog on March 5, 2021
ARA7618, Arrma FIRETEAM 6S BLX 4WD Brushless 1/7 Speed Assault Vehicle w/SLT3 2.4GHz Radio
The Arrma FIRETEAM 6S BLX Speed Assault Vehicle was developed for off-road domination! The FIRETEAM features an extra long wheelbase and widetrack suspension to deliver footed handling in rough terrain. Built on the 6S BLX platform, this ready-to-run 1/7 scale power house is the first of its kind. In fact, the FIRETEAM 6S BLX is incredibly capable and could very well be the toughest rig in the Arrma 6S BLX family.
The aggressive multi-panel body is inspired by military "fast attack" style vehicles used by military and private contractors around the world. The body comes factory-finished in either matte black or matte white camouflage, and features full roll cage beneath to add to the military feel and toughness. The detailed interior carries a four-man crew and is perfect for further personal customization. A special multi-terrain dBoots FIRETEAM wheel and tire combo finishes off the look, while providing drivers with high traction and smooth travel over rough off-road tracks. But once you dig in beneath the impressive body, you see why this model is so unique.
The FIRETEAM is the first Arrma off-road vehicle to include a mechanical handbrake! The mechanical handbrake feature adds a truly unique dimension to the FIRETEAM driving experience. Controlled from the third-channel thumb switch on the included Spektrum SLT3 transmitter, the handbrake allows the vehicle to perform evasive maneuvers, initiating drifts and handbrake turns unlike any electric off road vehicle before!
A factory-installed Spektrum 6S brushless system gives the FIRETEAM the power to perform huge jumps, and reach speeds of 60+ mph, while navigating brutal terrain. The extra-long wheelbase and wide-track suspension, along with aluminum oil-filled shocks help to maintain control when the road gets rough. From the bumpers and skid plates to the heavy-duty metal drivetrain, this bomb proof ARRMA design gives you the tools necessary to blast through obstacles that get in your path.
Fully assembled and complete with high-quality Spektrum gear, the FIRETEAM 6S BLX only requires your choice of EC5 or IC5 equipped LiPo batteries and charger to complete the mission.
FIRETEAM 6S BLX Features:
Military-styled, multi-panel body in matte black or matte white camo designs
Fully detailed interior featuring four FIRETEAM™ crew figures
Full body roll cage integrated with the chassis roll hoop, bumpers, and chassis side structures
Handbrake module operated by the Spektrum™ SLT3™ radio's third channel
Realistic bumpers, skid plates, and side steps
Black anodized aluminum shocks, motor mount, and steering parts
Aluminum-cased, oil-filled center differential
Multi-terrain dBoots® FIRETEAM™ tires featuring a military-inspired wheel and airless design tires
Standard 6S BLX Features:
Ready-to-Run
60+ MPH (97 km/h) speeds achievable in optimum conditions using a 6S LiPo battery and the include optional speed pinion gear
EXB front brace compatible top plate
Center body support and brace for maximum durability
Durable steel driveshafts throughout
Heavy-duty drivetrain
Never-loose red aluminum servo saver
Anodized aluminum chassis plate
Anodized aluminum front and rear shock towers
Spektrum™ SLT3™ 3-channel 2.4GHz radio and SR315 dual protocol receiver
Safe-D pinion and front and rear input cups
Large volume waterproof receiver box
Spektrum™ Firma™ 150A Smart waterproof 4S/6S ESC
Spektrum™ Firma™ 4074 2050Kv brushless motor
Never-pop ball ends
4-Bolt center diff removal
Easy-access sliding motor mount for quick motor removal
Durable wheel hubs for increased strength
Hub nut O-rings
Detailed decals
IC5® connectors (EC5™ compatible)
Spektrum™ S652 steel-geared waterproof digital servo offering 265 oz-in of torque @ 7.4V
Heavy-duty suspension arms
Rubber shielded bearings
All-metal drivetrain
Steel spur gear
Adjustable steel turnbuckles
ARRMA® motor heatsink and fan
2-year limited warranty (see manual for details)
Specifications:
Battery Tray Dimensions: 158x48x70mm
Final Drive Ratio: 17.92
Front Track: 17.71 in (450mm)
Rear Track: 17.71 in (450mm)
Wheelbase: 16.61" (422 mm)
Ground Clearance: 2.76 in (70mm)
Product Weight: 13.77 lb (6.26kg)
Scale: 1/7
Shock Type: 17.71 in (450mm)
Wheel Hex Size: 17mm
Wheel Width: 2.55 in (65mm)
Includes:
(1) ARRMA® 1/7 FIRETEAM™ 6S BLX 4WD Speed Assault Vehicle RTR
(1) Spektrum™ Firma™ 150A Smart Waterproof* ESC
(1) Spektrum™ Firma™ 4074 2050Kv Brushless Motor
(1) Spektrum™ 2.4GHz SLT3™ 3-Channel Transmitter
(1) Spektrum™ SR315 3-Channel Dual Protocol Receiver
(1) Spektrum™ SPMS652 Waterproof* Metal-Geared Digital Servo
(1) Handbrake Module with SPMS650 Waterproof* Brake Servo
(1) Product Manual
Needed to Complete:
(2) 2S or (2) 3S LiPo Batteries with EC5™ or IC5® connector
(1) Compatible Battery Charger
(4) AA batteries for Transmitter
This product was added to our catalog on February 10, 2022
ASC30128C, Team Associated Apex2 Nissan Z Sport RTR 1/10 Electric 4WD Touring Car Combo w/2.4GHz Radio, Battery & Charger
Since 1969, Nissan has been rewriting the rules of sports cars. The distinct styling, the relentless thrust of six cylinders pointing that long nose toward the horizon, a responsive suspension and stunning looks, the Nissan Z has captured the hearts of so many devoted sport cars admirers all over the world from different generations. With this Apex2 Nissan Z Sport, Team Associated has magnificently recreated this replica based on the 2023 Nissan Z equipped with the powerful 400-horsepower Twin-Turbo V6 engine for all of us fast sport cars enthusiast's to live and experience the thrill of putting the power to the pavement in 1/10 scale!
Fitted on the proven and popular Apex2 Sport chassis that features front and rear independent suspension, threaded oil-filled shocks, active rear toe, sealed gear differentials and a stout drivetrain, this vehicle packs some potent performance just like the real thing and is ready to lay some rubber down on the pavement in style!
Features:
Officially licensed
A-arm front and rear independent suspension keeps the Apex2 chassis under control during the wildest of driving conditions
Active rear suspension allows the toe to be adjusted through the suspension cycle, increasing or decreasing rear grip
A sealed center driveline keeps dirt and debris out for smooth and reliable power delivery
Reedy 550 15-turn 3-slot motor provides plenty of torque and tire ripping speed
Reedy SC500X programmable brushed ESC (program card sold separately)
Aluminum motor plate
Plastic body shock absorbers smooth out the bumps when cruising around the streets
Sealed receiver box
Steel dog bones and drive axles
Sealed front and rear gear differentials
Injection-molded brake calipers and rotors
Adjustable shock mounting locations
POM-filled injection molded pivot balls
Oilite bushings
Active rear toe suspension design
Molded one-piece tire rods and steering links
Bolt-on steering plates
Adjustable body post height locations
"Shorty" battery box
Specifications:
Scale: 1/10
Type/Terrain: On-Road Touring Car
Power plant: Brushed Electric
Drive Train: Shaft driven 4WD
Motor Size: 550 15T Brushed
Internal Gear Ratio: 2.6:1
Length: 444mm (17.48in)
Width: 190mm (7.48in)
Wheelbase: 259mm (10.2in)
Includes:
(1)Team Associated Apex2 Nissan Z Sport RTR 1/10 Electric 4WD Touring Car
(1) Reedy 2S(7.4V) 3000mAh Shorty WolfPack LiPo
(1) Reedy 324-S Compact Balance Charger
Needed to Complete:
(4) AA batteries for the transmitter
This product was added to our catalog on June 8, 2023
Introduction
The iconic paint scheme of the classic Grave Digger® 1950s-style panel van — a ghoulish blend of black, purple and green — has thrilled fans of the full-scale Monster Jam® legend for many years. Axial® Racing obtained the license from Feld Motorsports to offer the Grave Digger® for the first time as a true-to-scale, 4-wheel drive, straight-axle RC monster truck. The RC Grave Digger® rides on the Axial® SMT10™ tube frame chassis, which was developed for maximum bashing strength and an extremely detailed appearance. High-quality electronics also contribute to the Grave Digger® model’s never-say-die performance. Available ready-to-run, the vehicle comes with a 2.4GHz Spektrum™ radio system and powerful Dynamite® motor and ESC. Together with incomparable Axial® engineering, they make the 1/10 scale SMT10™ Grave Digger® the perfect bashing monster truck for everyone from scale RC enthusiasts to full-size monster truck fans. On grass, gravel, pavement and asphalt tracks, it’s ready to make your competition scream!
Overview
Monster Jam® is the world’s largest and most famous monster truck tour, where world-class drivers compete in racing and freestyle events before capacity crowds. One of its most celebrated attractions is Grave Digger®, which thrills monster truck fans with jaw-dropping, gravity-defying feats. For its part, Axial® Racing has become synonymous with RC crawler vehicles that inspire endless adventure and creative freedom. Put them together and you have a true-to-scale, 4-wheel drive, straight-axle Monster Jam® RC truck that’s the perfect basher for everyone from scale RC enthusiasts to full-size monster truck fans — the Axial® SMT10™ Grave Digger® 1/10 4WD Monster Jam® Truck RTR.
Licensed from Feld Motor Sports, Inc., the genuine Grave Digger® ‘50s-era panel van body is as ghoulishly real as it gets, from the trademark graveyard paint scheme and chrome Zoomie headers to the driver figure with glow-in-the-dark helmet. BKT Monster Jam® style tires with foam inserts add more scale realism along with impressive grip and handling on a wide range of terrain.
Everything going on beneath the scale body is just as exciting. Axial® designers went all out when creating the chassis and roll cage for the SMT10™ Grave Digger® monster truck. Very similar to those of full-size Monster Jam® trucks, the SMT10™ tube frame chassis was developed for maximum strength and has an extremely realistic appearance. There are a variety of shock mounting points for suspension tuning options, with additional mounting points on the cage and at the axle for moving the shocks to a more scale, vertical position if desired. Mated to the proven Axial® AR60™ axle, the 4-link suspension soaks up any obstacles in its path.
The Axial® SMT10™ Grave Digger® 1/10 4WD Monster Jam® Truck comes factory-built and ready-to-run with updated, improved electronics and radio gear. The Dynamite® 550-size motor provides higher torque and top speed for pulling off radical monster truck moves. It’s matched with a LiPo- and NiMH-compatible Dynamite® 60A ESC that features forward/brake/reverse, forward/brake and crawler drive modes.
The included FHSS 2.4GHz radio gear is all high-quality Spektrum™ brand equipment. The STX2® 2-channel transmitter and SRX200 receiver provide fast response and outstanding range. Enjoy precise, interference-free control while striking terror in your bashing competition!
Grave Digger, Monster Jam and all related logos and characters/designs are intellectual property of and used under license from Feld Motor Sports, Inc
Needed to Complete
2S LiPo Battery Pack with IC3™ connector
Battery Charger
(4) AA batteries for the transmitter
What's in the Box?
(1) Axial® SMT10™ Grave Digger® 4WD Ready-to-Run
(1) Spektrum™ STX2® 2.4GHz Transmitter
(1) Spektrum™ SRX200 Receiver
(1) Spektrum™ S614 Servo
(1) Dynamite® DYNS1222 12-Turn 550 Brushed Motor
(1) Dynamite® DYNS2210 60A FWD/REV Brushed ESC
Video Overview
CEG8992, CEN Ford F250 SD KG1 Lift Edition 1/10 RTR Custom Truck (Daytona Blue) w/2.4GHz Radio
The CEN Ford F250 SD KG1 Lift Edition 1/10 RTR Custom Truck brings the same incredible custom looks as offered with it's F450 big brother but with a fresh updated look. Featuring a true to scale F250 quad cab body, detailed side view mirrors, custom front and rear bumpers and a massive suspension lift it is hard to deny how awesome this truck looks! Adding to the custom truck theme is an RGB LED light positioned under the fenders. This light is selectable from the transmitter and gives you a multitude of color options showing off the impressive suspension. Supporting the F250 are two stout straight axles each located with four aluminum main links and a unique Watts link style pivoting axle mount. The Watts link takes the place of a typical panhard bar and keeps the axle centered throughout the suspension travel thus keeping any unwanted tire rubbing from happening. Finishing off the axles are a matching pair of front and rear sway bars keeping the truck level in heavy duty conditions.
Powering this beast is a high torque 540 brushed motor and Hobbywing SC-40A WP-1040 ESC giving you the power and control needed to take this truck to the extremes. CEN paid attention to the details with the drivetrain components as well, with hardened steel components, super scale features and a full selection of option parts designed to allow easy customization. Available in either a Burnt Copper body with black chrome wheels or a Daytona Blue body with chrome wheels gives you the ability to choose your own unique look. The CEN Ford F250 SD KG1 Lift Edition has the custom design you are looking for and is ready for the ultimate scale adventure!
Features:
SC-40A WP-1040-Brushed (Powered by HobbyWing):
Water-proof and dust-proof for all weather
Built-In Capacitor Module
Automatic throttle range calibration
Low voltage cut-off protection for Li-Po (lithium polymer) and NiMH battery
Over-Heat protection and throttle signal loss protection
Easily programmed with jumpers
Motor-RS-550 high Torque Motor (Power By Mabuchi Motor)
Servo -12Kg Servo O.E.M. by Savox:
4.8V 0.26 sec/60deg 10.0 kg-cm
6.0V 0.23 sec/60deg 12.0 kg-cm
25T Horn Gear Spline
Radio System:
Pistol-Grip Mod-3S 3 Channel Transmitter
Digital Trimming
Steering Dual-Rate (ST D/R) Adjustment
End Point Adjustment (EPA)
Built in Fail-safe
Chassis:
Steel Frame Rails
CMS (Chassis Mounted Servo) Chassis Design
Stamped Steel Shock Hoops
Steel Skid Plate
Full Precision Ball Bearing Support
Adjustable Turnbuckles
High Torque Servo Horn Safer
Suspension:
3 Links Suspension with Watts Link Design
Big Bore Oil Filled Adjustable Coil Over Shocks
Harden Steel Steering Drag Link
6mm Aluminum Linkage
Sway bar included
Drivetrain:
4 Wheel Drive
Center Shaft Drive Train for more power transferred to the wheels
Highly Efficient Transmission System
Wide Range Easy Changeable Gear Box Design
Sealed transmission eliminates dirt and dust
Sealed Axle housing
5mm Hardened Steel Axle shaft
Differential Center Locker Front/Rear Planetary Gear Type
Metal Transmission Gears
Planetary Gear type Differential
Specifications:
Length: 25.60inch (650mm)
Width: 10.04inch (255mm)
Wheelbase: 16.02inch (407mm)
Ground Clearance: 3.54inch (90mm)
Weight: 5.51 lb. (2.5kg)
Battery: 2s Lipo recommended
Includes:
(1) Ford F250 SD KG1 Lift Edition 1/10 Scale RTR Custom Truck
Needed To Complete:
2S Lipo w/T-Style Connector
Battery Charger
(4) "AA" Batteries for Transmitter
This product was added to our catalog on September 30, 2022
CEG8993, Ford F250 1/10 4WD KG1 Edition Lifted Truck, Burnt Copper - RTR
RGB LED Light: Standard Under Fender Multicolor RGB LED.
ESC: 40A WP-1040-Brushed (By HobbyWing)
Water-Proof and Dust-Proof for All Weather.
Built-In Capacitor Module.
Automatic Throttle Range Calibration.
Low Voltage Cut-Off Protection for Li-Po and NiMH Battery.
Over-Heat Protection and Throttle Signal Loss Protection.
Motor: RS-540 High Torque Brushed Motor.
Servo: 12Kg Metal Gear Servo (By Savox)
4.8V - 0.26 sec/60 10.0 kg-cm.
6.0V - 0.23 sec/60 12.0 kg-cm.
25T Horn Gear Spline.
Radio System: Pistol-Grip Mod-3S 3 Channel Transmitter and Receiver
Digital Trimming.
Steering Dual-Rate (ST D/R) Adjustment.
End Point Adjustment (EPA).
Build in Failsafe.
Frequencies: 2.4GHz
Power Supply: 4
AA Alkaline (Not Included).
Body: Official Licensed by Ford Motor
F-250 Super Duty.
Scale Realistic Body Details.
Black Bed Liner Coating.
hard Molded Front & Rear bumpers with build in 3mm LED housing
Chassis:
Steel Frame Rails.
CMS (Chassis Mounted Servo) Chassis Design.
Stamped Steel Shock Hoops.
Steel Skid Plate.
Full Precision Ball Bearing Supported.
Adjustable Turnbuckles.
High Torque Servo Saver Horn.
Easy Access Battery Tray.
Battery Tray Size 146 x 50 x 25mm.
Suspension:
Custom Lifted Suspension Design.
110mm Big Bore Oil Filled Adjustable Coil Over Shocks.
12mm over size shock body with 3mm Hardened Steel Polished Shaft.
Harden Steel Steering Drag Link.
CNC Machined 6mm Aluminum Linkage.
Front / Rear Sway Bar.
Drivetrain:
Full Metal Transmission Gears.
4 Wheels Drive.
Center Shaft Drivetrain for More Power Transferred to the Wheels.
Hight Efficient Transmission System.
Wide Range Easy Changeable Gear Box Design.
Sealed Transmission Case.
Sealed Axle Housing.
Metal Planetary Gear Type Differential.
Gear Ratio:
Hi / Speed Ratio 1.56:1
Hi / Torque Ratio 2.8:1
Spur / Pinion Gear 32p85/32p12T
Ring & Pinion Gear30/15T 2:1
Wheel: Official Licensed by KG1 Forged
KF004 Vile Wheel.
66.50mm x 37.5mm.
Tires: Official Licensed Fury Tires
Low Profile Country Hunter tires.
65 x 100.50 x 38.50 mm.
Specifications:
Length: 25.6 inches (650mm)
Width: 10.04 inches (255mm)
Wheelbase: 16.02 inches (407mm)
Ground Clearance: 3.54inch (90mm)
Weight: 5.51 lb. 2.5 kg
Recommended Battery: 2S 5000mAh LiPo Battery with dean connector
This is a replacement set of two CEN F450 SD Matte Silver Shock Springs, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on March 4, 2021
This is a replacement set of two CEN F450 SD M3x43mm Shock Shafts, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on March 4, 2021
This is a replacement CEN F450 SD Sway Bar Mount, intended for use with the CEN Ford F450 SD scale truck. Package includes left and right side sway bar mount brackets.
This is a replacement CEN F450 SD 105mm Front Center Drive Shaft, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on February 16, 2021
CEN F250 Center Drive Shaft. This is a replacement center drive shaft intended for the CEN Ford F250 truck. Package includes one 160.45mm long center driveshaft.
This is a replacement set of two CEN F450 SD M3x117mm Threaded Silver Aluminum Links, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on February 16, 2021
This is a replacement CEN F450 SD Chassis Rail Set, including rail A & B, intended for use with the Ford F450 SD 1/10 RTR Custom Dually Truck.
This product was added to our catalog on March 15, 2021
This is a replacement set of two CEN F450 SD Metal 4-Link Suspension Stays, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on February 15, 2021
This is a replacement CEN F450 SD Steady Bearing Holder, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on February 16, 2021
This is a replacement CEN F450 SD 4-Link Support and Chassis Support Bracket set, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on February 15, 2021
CEN F250 Servo Saver Set. This is a replacement servo saver set intended for the CEN Ford F250 truck. Package includes one servo saver top, one servo saver bottom with a 25T spline and one extended servo saver arm.
CEN Racing F450 American Force H01 Contra Hub Cover. These replacement hubcaps are intended for the Cen Racing F450. Package includes two black hubcaps and two decals.
This product was added to our catalog on September 28, 2021
CEN Racing F450 American Force H01 Contra Hubcap. These optional hubcaps are intended for the Cen Racing F450. Package includes two chrome hubcaps and two decals.
This product was added to our catalog on September 28, 2021
CEN Racing F450 Front and Rear Light Buckets. These optional front and rear light buckets come clear and are ready for you to paint and cut. Package includes one clear light bucket set, one length of double sided tape and LED mounts.
This product was added to our catalog on September 28, 2021
This is a CEN F450 SD Body Holding Block Set, intended for use with the CEN Ford F450 SD scale truck. Package includes four hex and four round type holding blocks.
This product was added to our catalog on February 16, 2021
CEN Racing F450 Aluminum 4th Link Mount. This optional 4th link mount is intended to add strength to the CEN Racing F450. Package includes one mount and hardware.
This product was added to our catalog on September 28, 2021
CEN Racing F450 Aluminum Differential Cover. This optional differential cover is made from aluminum and anodized red to add style to the CEN Racing F450. Package includes one differential cover and hardware.
This product was added to our catalog on October 11, 2021
CEN Racing F450 69mm Aluminum Front Upper and Lower Suspension Links. Made from CNC machined aluminum and anodized red, these optional links are intended for the CEN Racing F450. Package includes three unassembled front links. NOTE: Does not includes the front 4th link. Please use CEGCKD0378 for the correct 4th link.
This product was added to our catalog on October 14, 2021
CEN Racing F450 57mm Aluminum Panhard Bar & Steering Tie Rod. Made from CNC machined aluminum and anodized black, these optional links are intended for the CEN Racing F450. Package includes one steering link, one front panhard link, one rear panhard link and hardware.
COMPATIBILITY
CEN Ford F450
The KAOS CEN F450 Rear Bumper Crossmember is a replacement for the CEN F450 SD scale truck equipped with the optional Aluminum Trailer Tow Hitch (CEGCKD0450). Package includes one bumper crossmember.
This product was added to our catalog on May 12, 2021
CEGCKD0801, Pro RGB Light Conversion Kit for F450 Chasiss w/Pro Module
Pro RGB Light Conversion Kit for F450 Chassis w/Pro Module
CKD0801 KAOS RGB Light Conversion kit for F450 SD (F450 Chassis only w/ control Module)
This is Standard RGB kit for F450 SD
Including all the mounting wares
Include RGB MODULE which controls multi color changes
KAOS F450 SD Custom Truck Lift Conversion Kit
CKD1000 KAOS F450 SD Custom Truck Lift Conversion kit. This is a full lift kit and includes everything you need to take your F450 SD to the next level. Whether you want to tackle new terrain, or just stand out above the rest, this lift kit is what you need.
Features:
Full lift kit for F450 SD only
Includes 110mm full aluminum shock sets
Watt design links for prefect geometry
Item First Received: 12/13/2022
This is a replacement pack of four CEN F450 SD 1.8mm Tension Bars, intended for use with the CEN Ford F450 SD scale truck.
This product was added to our catalog on February 15, 2021
