BetaFPV
BetaFPV BetaFPV RTF Cetus Pro FPV Analog Kit - Cetus Pro Whoop, Goggles, Transmitter, Batteries, Charger & Case
All batteries must be shipped by a ground shipping method. The Cetus Pro FPV Kit is finally here! It is the best ideal choice for beginners to advance currently. Comes with a Cetus Pro brushless quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles. It's more powerful and maneuverable for all starters as well as FPV pros to practice indoor and outdoor. Be sure to pick up some extra batteries so that you can fly all day! We recommend the following 1S batteries for this quad: BetaFPV 1S 450mAh - BT2.0 Check out our other RTF combos, all our pre-built quads and our BetaFPV selection! Features The auxiliary flight function is greatly reducing the threshold of operating. This is the lightest key to open the door to advanced FPV. Cetus Pro quadcopter comes with a brushless power system, it's more powerful and maneuverable in flight. Pilots can achieve more FPV freestyle actions to train. With the self-protection of emergency landing when out of control or in low battery, to ensure a more safe flight. Made of PA12 material, the frame has an excellent impact resistance in drop & impact. Meanwhile, the 360° protection of the whoop frame ensures safe flights both indoors and outdoors. All items needed for the flight are packed in an EVA portable storage bag. Better to protect and convenient to carry. Specifications BetaFPV LiteRadio 2 Frequency Range: 2.4GHz (2403MHz-2447MHz) 2.4G System: NRF24L01 or CC2500 Channel: 8 Support Protocol: Bayang / Futaba S-FHSS / Frsky D16 FCC/ Frsky D16 LBT/ Frsky D8 Power: ≤100mw Adapted Drone Type: Multirotor Support USB Charging / Firmware Update Support BETAFPV Simulator Connected / Customized LiteRadio System / Joystick Calibration LED Light: Green-Power On / Red-Warning / Blue-Normal Battery: Built-in 1000mAh 1S Battery Charging Connector: Type-C BetaFPV VR02 Goggles Screen Size: 4.3" Screen Resolution: 800x480p Screen Brightness: 300cd/m2 Field of View: 55° Charging Port: USB-C Input Voltage: 3.7V 500mA Internal Battery: 3.7V 2000mAH Dimensions: 143x126x86.3mm Weight: 300g BetaFPV RTF Cetus Pro Positioning system: Optical flow / Barometer / Laser Height Positioning: Laser / Barometer Angle Locating: Optical flow ( effective height 0.3-3m) Accuracy of auto-hover: Horizontal ±0.2m, vertical ±0.3m (under no wind environment) Receiver protocol: Frsky D8 VTX: 25mW Camera tilt degree: 25° Camera: C02 FPV Micro Camera Propeller: 40mm 3-blade 1.5mm shaft hole Power system: 1S Battery: BT2.0 450mah 1S Battery (external) Flight time: 4-5min Flight distance: 80m (Clear line of site) Includes 1x Cetus Pro Brushless Quadcopter 1 LiteRadio2 SE Transmitter (Frsky D8 Protocol) 1x VR02 FPV Goggles 2x BT2.0 450mAh 1S Lipo Battery 1x BT2.0 Battery Charger and Voltage Tester 1x USB Charging Cable (Type-C) 1x Type-C Adapter 1x Prop Removal Tool 1x Portable Storage Bag
$229.99
RaceDayQuads BetaFPV M03 25-350mW 5.8G Micro VTX - U.FL
M03 VTX, an ultralight and high output power 5.8GHz analog VTX, is designed for 65-85mm whoop drone for longer-range flying. Check out all our Micro/Nano VTXs and all our BetaFPV gear! Features With the 25-350mW output power, the M03 VTX provides a stable image and strong transmission. Only 1.1g and a tiny size for drones like 65-85mm whoop drones. The screw mounting holes pattern is suitable with BETAFPV micro canopy. The camera connector JST-0.8 is suitable for the BETAFPV C02 camera. Comes with IPX type of antenna, just plug and play, no extra solder work needed. M03 VTX is perfectly suitable for the 65-85mm whoop drone. We highly recommend using it with ELRS 2.4G FC board, like F4 1S 5A FC (ELRS 2.4G) or F4 1S 12A FC (ELRS 2.4G). Diagram Below is the diagram of the M03 VTX. The camera connector is JST-0.8 and it is compatible with cameras like BETAFPV C01, BETAFPV C02, and NewBeeDrone BeeEye. How to connect with the Flight Controller Here is the diagram about how to connect the M03 VTX with F4 1S 5A FC (ELRS 2.4G) board. Here is the diagram about how to connect the M03 VTX with F4 1S 12A FC (ELRS 2.4G) board. Change Band & Band & Chnanel & Power M03 VTX could only use the Smart Audio port to change the band and channel. Enter the OSD menu by radio transmitter sticks ( Pitch Stick UP and Yaw Stick Left). Then FEATURES -> VTX SA to change the frequency point and power. Switchable power includes 25mW, 100mW, 200mW and 350mW. Except for the method via OSD menu as show above, the output power could be changed via the power button. Specifications Item: M03 5.8G VTX Output power: 25/100/200/350mW (adjustable) Supply voltage range: 4.5-5.5V Weight: 1.1g (antenna not included) VTX internal size: 18X14mm Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz Channel SEL: SmartAudio Modulation type: FM Frequency control: PLL All harmonic: Max -50dBm Frequency stability: ±100KHz (Typ.) Frequency precision: ±200KHz (Typ.) Channel carrier error: ±1.5dB Antenna port: 50 Ω Operating temperature: -10℃~+80℃ Camera connector: JST-0.8, compatible with cameras like BETAFPV C01, BETAFPV C02 and NewBeeDrone BeeEye. Includes 1x BetaFPV M03 25-350mW 5.8G Micro VTX - U.FL 5x 30AWG silicone wire (30mm)
$25.99
BetaFPV BFPV-00313881, BetaFPV Cetus FPV RTF Drone Combo Kit
BFPV-00313881, BetaFPV Cetus FPV RTF Drone Combo Kit The Cetus FPV Kit offers an exceptional opportunity for FPV beginners to explore the thrilling world of First-Person-View flying. This all-inclusive kit, comprising the Cetus brushed quadcopter, LiteRadio2 SE transmitter, and VR02 FPV Goggles, brings everything you need for an immersive FPV experience. The auxiliary flight function makes it a breeze for everyone to take to the skies, greatly reducing the learning curve for newcomers. With three distinct flight modes Normal, Sport, and Manual, with three speed settings, the Cetus FPV Kit can cater to a wide range of pilot preferences and flight environments. The Cetus quadcopter features an altitude hold function that simplifies flying and ensures stable indoor hover, thanks to an accurate barometer and laser system. Additionally, it boasts self-protection mechanisms for emergency landings and automatic motor disarming in the event of a collision. The LiteSilver system within the quadcopter integrates Frsky D8, Rx 25mW VTX, barometer, laser, and optical flow sensor for optimal performance. The LiteRadio2 SE transmitter, with its built-in 1000mAh 1S battery, offers an impressive 8-hour endurance, making it ideal for extended flight sessions. The VR02 FPV Goggles provide an immersive FPV experience, featuring high-quality antennas for clear, stable reception, ergonomic design for comfort, and simplicity of operation. The Cetus FPV Kit is the perfect entry point into FPV flying for beginners and a robust choice for enthusiasts. Features: Perfect for indoor fun 3 Flight modes Normal, Sport, and Manual Mode Self-developed LiteSilver System Self-protection Function Auto hold hovering Durable PA12 Frame Impressive 4-5 minute flight times Low voltage protection Automatic calibration makes preflight a breeze Small and convenient FPV supported Specifications: Weight: 1.23oz (35g) Protocol: Frsky D8 Flight Controller: Cetus FC V3.0 VTX: 25mW Camera: CO2 FPV Micro Goggles: VR02 Propeller: 31mm 4-Blade w/0.8mm Shaft Motor: 716-19000KV Brushed Motor Flight Time: 4-5 Minutes Flight Distance: 80m (interference-free environment) Assembly Level: RTF Includes: (1) Cetus FPV Kit (1) LiteRadio2 SE Transmitter (1) VR02 FPV Goggles (1) CO2 FPV Micro Camera (2) BT2.0 3.7V 300mAh 1S Lipo Battery Charger and voltage tester (4) Spare 31mm 4-Blade props (1) Portable storage bag Needed to Complete: Everything you need is included This product was added to our catalog on October 21, 2023
$175.00
BetaFPV BFPV-01020005_2, BetaFPV Cetus X FPV RTF Drone Combo Kit w/BetaFPV Cetus Flight Controller
BFPV-01020005_2, BetaFPV Cetus X FPV RTF Drone Combo Kit w/BetaFPV Cetus Flight Controller The Cetus X FPV Kit is designed for both seasoned pilots and newcomers, offering an advanced 2S power whoop bundle that propels your FPV experience to new heights. Comprising the Cetus X Brushless Quadcopter, LiteRadio 3 Radio Transmitter, and VR03 FPV Goggles, it's a complete package to elevate your FPV game. With the inclusion of the latest BT2.0 450mAh 1S Battery, you'll enjoy extended flight times and higher discharge rates. This kit unlocks a new level of control and flying experience, featuring unparalleled control and extended radio and video transmission. It's a fantastic entry point for beginners to dive into the world of FPV, thanks to its accessibility and potential for growth. The Cetus X offers a variety of flight modes and speeds to suit different pilot preferences and flight environments The FPV kit combines cutting-edge components, including the Betaflight FC for powerful flight control, and The VR03 FPV Goggles are equipped with DVR recording, allowing pilots to capture and relive their most exciting moments. The Cetus X Brushless Quadcopter, combined with the advanced components in this kit, provides you with an outstanding FPV experience that's hard to match. The LiteRadio 3 SE transmitter offers fantastic versatility as it is compatible with a range of popular drone racing simulators, including Drone Racing League (DRL), DCL, Uncrashed, and Liftoff. This compatibility ensures an immersive and realistic training experience for aspiring drone racers and enthusiasts. Whether you're honing your skills or mastering the art of FPV flight, the LiteRadio 3 provides a seamless connection to these renowned simulators, making it a valuable tool for both beginners and experienced pilots. Features: Perfect for indoor fun Flight modes Normal, Sport, and Manual Mode Turtle Mode makes crash recovery a breeze Self-developed LiteSilver System Auto hold hovering Powerful 2S compatibility Tilt Camera Durable PA12 Frame Impressive 4-5 minute flight times Low voltage protection Automatic calibration makes preflight a breeze Small and convenient FPV supported LiteRadio compatible with FPV Flight simulators like DRL, DCL, Uncrashed, and Liftoff all Available on Steam Specifications: Wheelbase: 3.74in (95mm) Weight: 1.94oz (55g) Protocol: Frsky D8 Flight Controller: Cetus FC V3.0 VTX: 25-400mW M04 Camera: CO4 FPV Micro Goggles: VR03 Propeller: Gemfan 2020 4-Blades Motor: 1103-1100KV Brushless Motors Flight Time: 4-5 Minutes Flight Distance: 80m (interference-free environment) Assembly Level: RTF Includes: (1) Cetus X FPV Kit (1) LiteRadio 3 SE Transmitter (Frsky) (1) VR03 FPV Goggles (1) CO4 FPV Micro Camera (4) BT2.0 3.7V 450mAh 1S Lipo Battery Charger and voltage tester (4) Spare Gemfan 2020 4-Blades (1) Portable storage bag Needed to Complete: Everything you need is included This product was added to our catalog on October 21, 2023
$315.00
BetaFPV BFPV-01020010_5, BetaFPV Cetus Lite FPV RTF Drone Combo Kit
BFPV-01020010_5, BetaFPV Cetus Lite FPV RTF Drone Combo Kit The Cetus Lite FPV Combo is your gateway to the exciting world of FPV flying. This ready-to-fly kit is perfect for beginners, offering a safe and thrilling experience for both kids and adults. It features an auxiliary altitude hold function, making it easy for users to control and navigate. The durable frame, constructed from impact-resistant PA12 material, is equipped with a protective guard, ensuring safe flights indoors and outdoors. With the high-efficiency BT2.0 300mAh 1S battery, you can enjoy flights lasting around 4-5 minutes, and swapping batteries is a breeze. The Cetus Lite also includes a low-voltage prompt function to protect your battery. Automatic calibration simplifies your flying experience, ensuring stability every time you take off. With the Altitude Hold feature and the LiteRadio 1 transmitter, even newcomers can effortlessly control the quadcopter's height, while the included VR02 goggles provide an immersive FPV experience. The LiteRadio 1 transmitter offers fantastic versatility as it is compatible with a range of popular drone racing simulators, including Drone Racing League (DRL), DCL, Uncrashed, and Liftoff. This compatibility ensures an immersive and realistic training experience for aspiring drone racers and enthusiasts. Whether you're honing your skills or mastering the art of FPV flight, the LiteRadio 1 provides a seamless connection to these renowned simulators, making it a valuable tool for both beginners and experienced pilots. Features: Perfect for indoor fun Auto disarming upon collisions Auto hold hovering Durable PA12 Frame Impressive 4-5 minute flight times Low voltage protection Automatic calibration makes preflight a breeze Small and convenient FPV supported LiteRadio compatible with FPV Flight simulators like DRL, DCL, Uncrashed, and Liftoff all Available on Steam Specifications: Length: 3.5in (90mm) Width: 3.3in (85mm) Height: 1.7in (45mm) Weight: 1.26oz (36g) Protocol: Frsky D8 Flight Controller: Cetus FC V3.0 VTX: 25mW Propeller: 31mm 4-Blade w/0.8mm Shaft Motor: 716-19000KV Brushed Motor Flight Time: 4-5 Minutes Flight Distance: 80m (interference-free environment) Assembly Level: RTF Includes: (1) Cetus Lite (1) LiteRadio Transmitter (1) VR02 FPV Goggles (1) Cetus Lite Camera and VTX (2) BT2.0 3.7V 300mAh Lipo Battery Charger and voltage tester (4) Spare 31mm 4-Blade props (1) Spare 716 CCW Motor (1) Spare 716 CW Motor Needed to Complete: Nothing! Everything needed for lift off is included This product was added to our catalog on October 21, 2023
$135.00
RaceDayQuads TweetFPV Grip Tape for BetaFPV LiteRadio 2 - Choose Your Color
Custom grip tape set for the BetaFPV LiteRadio 2 series transmitters. Check out all our RC Transmitters & Accessories, as well the rest of our TweetFPV products. Includes 1x TweetFPV Grip Tape for BetaFPV LiteRadio 2
$9.99
RaceDayQuads RDQ Series Battery Adapter for Mobula7 and BetaFPV Whoop Mod - 3D printed TPU - Choose Your Frame
This 3D print is meant to adapt the RDQ Series 300mah 2S 70C 7.6V HV FPV Micro Battery to several of the 2S whoops that we carry. The Mobula7 V1 or V2 frame adapter is meant to carry (2x) of the 250mah 3.8v HV 1s PH2.0 RDQ Whoop Battery. The Whoops the print is designed for are: Mobula7 V1 or V2 Frame Mobula7 V3 Frame Beta75 Pro Frame Beta75X 2S Frame Dont forget to check out all of our whoop products! Check out all our 3D printed accessories! Includes 1x RDQ Series Battery Adapter for Mobula7 and BetaFPV Whoop Mod
$0.49
RaceDayQuads RDQ Series 7.6V 2S 300mAh 70C LiHV Micro Battery - XT30
All batteries must be shipped by a ground shipping method. The RDQ Series Batteries expand their lineup, now offering 300mah size packs in 2s with XT30 a connector, designed to be perfect with the BetaFPV BETA75X brushless whoop! RDQ Series Lipos are known and loved by the community for their keen ability to push harder than any other pack on the market, flight after flight, all while offering the user an unmatched level of value. Check out the entire RDQ Series of LiPo and LiHV battery packs! This battery is compatible with following whoops without modification: Beta75 Pro 2 Beta75X Mobula7 with the V3 Frame Mobula7 HD Specifications Capacity: 300mAh Size: 51x16.7x12.5mm Weight: 20.28g Balance lead: 30.5mm XT30 length: 40.5mm Includes 1x RDQ Series 7.6V 2S 300mAh 70C LiHV Micro Battery - XT30
$6.24
RaceDayQuads RDQ Series 7.4V 2S 450mAh 70C LiPo Micro Battery (Long Type) - XT30
All batteries must be shipped by a ground shipping method. The RDQ 450mah 2S battery is a tremendous combination of performance and value. Give your micro setups plenty of pop with the battery's rated 70c output and XT30 connector! NOTE: This battery is not compatible with BetaFPV 75X frame. Check out the entire RDQ Series of LiPos and all our 2S Batteries Specifications Capacity: 450mAh Size: 60.7x13.5x16.5mm Weight: 28.9g Balance lead: 37mm XT30 length: 53mm Includes 1x RDQ Series 7.4V 2S 450mAh 70C LiPo Micro Battery (Long Type) - XT30
$8.49
RaceDayQuads Meteor65 Air Brushless Whoop Frame - Choose Your Color
The Meteor65 frame has been upgraded to the Meteor65 Air Brushless Whoop Frame, reducing the minimum weight to an impressive 2.67 grams. This remarkable frame features enhanced strength and durability plus a new motor fixed slot and optimized low profile design, making it the ultimate choice for those seeking a Sub18g 65mm 1S Whoop drone with an ultra-light structure. Check out all our whoop frames & accessories and all our BetaFPV gear! Features Weighing a mere 2.67g, this Meteor65 Air Brushless Whoop Frame exemplifies exceptional ultra-light structure while maintaining remarkable durability and crash resistance. A groundbreaking addition to the 65mm frame, the inclusion of motor fixed slots enhances the convenience and stability of the motor installation.The low profile design effectively concentrates the whoop drone's gravity, optimizing its flight performance. The deliberate increase in whoop duct diameter effectively mitigates the risk of propeller strikes, ensuring seamless compatibility with 0702 motors and 0802 motors, and 31mm propellers. ComparisonBased on the Meteor65 frame, we have optimized and upgraded in many aspects, the details are as follows. The duct diameter is enlarged from 32mm to 34.9mm, which improves compatibility and avoids propeller strikes. The weight is reduced from 3.14g to 2.67g, making the flight more flexible, exemplifying the exceptional ultra-light structure of the 1S whoop drone. Both frames feature the same materials and durability. With the low profile of frame, the drone's gravity center is more concentrated and improves the sense of compactness. Motor Fixed SlotIn a groundbreaking development, the Meteor65 Air Brushless Whoop Frame has been added firstly with motor fixed slots, facilitating a more expedient and steadfast motor installation process. While misalignment has no measurable effect on motor efficiency, correct shaft alignment ensures the smooth, efficient transmission of power from the motor to the flight controller, reduces mechanical stress, and minimizes power wastage. For advanced pilots who have strict requirements for assembling the ultra-light 1S whoop drone, this new design undoubtedly adds the finishing touch. Endless PersonalizationWe enhance frame structure design and also provide diverse color options for drone frames, enabling greater freedom for choice. This allows for aligning or color clashing the frame color with your drone's theme. And equipped with our various colors of ultra-light Micro Air Canopy adds more possibility of capturing the optimal image. Your drone will capture people's attention and showcase your unique personality and creativity. Micro Air CanopyWe also have devised an exceedingly light Micro Air Canopy, weighing a mere 0.74g, that not only facilitates camera angle adjustment from 25° to 50° but also has antenna mounts, incorporated at the tail. If your goal is to optimize canopy functionality while minimizing weight to obtain a Sub18g 65mm Whoop, this option stands as the definitive choice. Specifications Item: Meteor65 Air Brushless Whoop Frame Material: PP Weight: 2.67g Wheelbase: 65mm Motor Mounting: 3-M1.4-6.6mm Flight Control Installation Hole: 26×26mm Battery Slot Size: 11.6×6.0mm Color: Black, White, Transparent White, Transparent Blue, Transparent Purple, Transparent Green Includes 1x Meteor65 Air Brushless Whoop Frame - Choose Your Color
$4.99
RaceDayQuads HappyModel SE0702 0702 28,000Kv Micro Motor - Choose Rotation
Make your drone projects even better with this HappyModel SE0702 0702 28000Kv Micro Motor. Its high-quality design offers efficient operation and reliable performance, giving your projects the boost they need. Make the most of your flying with this micromotor. These motors come with a JST 1.25 plug-in piece for a secure connection for HappyModel boards as with BetaFPV too. Check out our other Micro Motors, and all our HappyModel selection! Specifications Brand Name: Happymodel Mode: SE0702 KV Option: KV28000 Configuration: 9N12P Stator Diameter: 7mm Stator Length: 2mm Shaft Diameter: Φ1mm Motor Dimension(Dia.xLen):Φ 9.5mmx14mm Weight(g): 1.5g No.of Cells(Lipo): 1S only Includes 1x HappyModel SE0702 0702 28000Kv Micro Motor - Choose Rotation (CW or CCW) 4x Motor Hardware
$8.99
RaceDayQuads GEPRC CL25 Cinelog25 Cinewhoop 2.5" Micro Frame Kit
Does not come with naked Gopro mount. Please refer to the includes list at the bottom of the listing for all included items. The classic CL25 Frame, designed by the GEPRC team, has been upgraded. They've redesigned the shock absorption structure of the camera mount, eliminated the jelly coming from the FPV camera, and you can now use 3, 4, and 5 damping rings according to the flight state to obtain the best stability in vibration and noise. The CL25 can be used for Vista HD digital image transmission system or Analog image transmission system. The center of gravity of the quadcopter is in the middle, Check out all our DJI-compatible frames, electronics, and accessories as well as our whole GEPRC product line! Specifications Dimensions: 109mm Frame Style: Cinewhoop Top Plate: 2.5mm Bottom Plate: 1.5mm Bottom Plate(camera): 2mm Stack Size: 26.5x26.5mm Motor Mount: 9x9mm (compatible with 1105/1204/1206 motors) Camera Mount: 14-20mm (Nano and Micro-sized) Weight: 47.8g Recommended: Motor: BetaFPV 1404 4500Kv Micro Motor 4 Pack FC/ESC: GEPRC F411 2-6S AIO Flight Controller w/ 35A 4in1 ESC Prop: Gemfan D63 Ducted Durable Tri-Blade 2.5" Cinewhoop Prop 8 Pack LiPo: RDQ Series 14.8V 4S 650mAh 80C LiPo Micro Battery Includes 1x Top plate 2.5mm 1x Bottom plate 1.5mm 1x Bottom Plate (Camera)1.5mm 4x (M2x3.5x25mm) Aluminum posts 2x (M2x3.5x8mm) Aluminum posts 28x (M2x6mm) YFS Round head screws 2x (M2x8mm) YFS Round head screws 4x (M2x12mm) YFS countersunk head screws 16x (M2x2mm) Nylon Nuts 4x (M2x18mm) YFS countersunk head screws 5x Damping Rings 1x (19x19mm) Mount of camera 1x (14x14mm) Mount of camera 1x 3D print part of XM antenna 1x 3D print part of TBS antenna 1x Naked Camera Mount (This is just the base, NOT the actual camera case) 2x Batteries pads 2x EVA Landing pads 4x 2.5-inch Guards 1x EVA Damping Ring of Guard 2x Antenna Tubes 2x Batteries straps (M15x150mm）
$31.99
RaceDayQuads Fractal Engineering Fractal 75 Pro Max Micro/Whoop Frame Kit - Choose Your Version
From motorpost to motorpost on this frame, the distance is 84mm. Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 Pro Max was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 75 Pro Max whoop micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Pro Max Whoop Micro-frame kit and BetaFPV Meteor75 Pro Whoop Frame. Note: This is designed for prop guards that fit 45mm props like the Meteor75 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. The Pro Version has been scaled to the max to fit 45mm props Check out our other Micro frames, and our Fractal Engineering Products! Features A completely new variant of the F75, but this is actually 84mm motorpost to motorpost distance. The same winning recipe, scaled to fit 45mm props with ducts while keeping the camera up front Extended camera mount to reduce prop guards in view Low center of gravity, by bringing the AIO close to the frame/motors Allows mounting with USB pointed up for easy accelerometer calibration Easy maintenance, break a duct, replace only the single duct No need for a canopy as all electronics are tucked safely between the ducts Approximately 21g using the Happymodel DiamondF4 AIO Recommended Parts List Gemfan Ducted 1815 Tri-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color Gemfan Ducted 1815 Bi-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color HappyModel RS 0802 20,000Kv Micro Motor - Choose Version HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz HappyModel OVX300 25-300mW 5.8GHz U.Fl VTX w/ OpenVTX FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 2.21g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
$22.99
RaceDayQuads Fractal Engineering Fractal 75 Micro/Whoop Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 75 whoop micro Frame Kit Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Whoop Micro Frame Kit and HappyModel Mobula7 V4 Whoop frame. Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 75mm whoop frame, and that will serve as your protection for you motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. Check out our other Micro frames, and our Fractal Engineering Products! Features 75mm diagonal, squished X geometry, for 40mm props 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction. Cut from Japanese T300 CF sheet Low-profile camera mount, no props in view, no tilt offset Low Center of gravity, by bringing the AIO closer to the frame/motors Allows mounting with USB pointing up for easy accelerometer calibration No need for a canopy as all electronics are tucked safely between the ducts Maximum rigidity where it matters most; connecting the motors to the FC Easy maintenance, break one duct, replace only the single duct Lightweight, about 21g with HM DiamondF4 Recommended Parts List HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack - Grey HappyModel RS 0802 20,000Kv Micro Motor - Choose Version HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 2.1g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
$22.99
RaceDayQuads Fractal Engineering Fractal 65 Pro Micro/Whoop Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 Pro was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 65 Pro Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Pro Whoop Micro Frame Kit and Meteor65 Pro Whoop frame. Note: This is designed for prop guards that fit 35mm props like the Meteor65 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. The Pro version has been squished to the max to fit 35mm props with Meteor 65 Pro ducts. Check out our other Micro frames, and our Fractal Engineering Products! Features A variant of the Fractal 65 frame kit Squished to the max to fit 35mm props with Meteor 65Pro ducts Maintains 65mm motors distance to meet racing specs Still fits the camera between the front ducts 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction Low-profile camera mount, no props in view, no tilt offset Low Center of gravity, by bringing the AIO closer to the frame/motors Allows mounting with USB pointing up for easy accelerometer calibration No need for a canopy as all electronics are tucked safely between the ducts Maximum rigidity where it matters most; connecting the motors to the FC Easy maintenance, break one duct, replace only the single duct Recommended Part List BetaFPV Gemfan 1406 Tri-Blade 35mm Micro/Whoop Prop 4 Pack (1mm Shaft) - Choose Your Color HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 1.8g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
$20.99
RaceDayQuads Fractal Engineering Fractal 65 Micro/Whoop Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5. Choose between getting the Fractal 65 Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Whoop Micro Frame kit and HappyModel Mobula6 Whoop frame. Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 65mm whoop frame, and that will serve as your protection for your motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks. Check out our other Micro frames, and our Fractal Engineering Products! Features 65mm diagonal, squished X geometry, for 31mm props 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction Low-profile camera mount, no props in view, no tilt offset Low Center of gravity, by bringing the AIO closer to the frame/motors Allows mounting with USB pointing up for easy accelerometer calibration No need for a canopy as all electronics are tucked safely between the ducts Maximum rigidity where it matters most; connecting the motors to the FC Easy maintenance, break one duct, replace only the single duct Recommended Part List Gemfan Durable 1210 Bi-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft) Gemfan 1219-3 Durable Tri-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft) - Choose Your Color HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6 HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz FEA optimization test preformed ensuring the stress gets spread out across the whole structure without concentrations Specifications CF Weight: 1.6g Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount Stack Size: 25x25mm Includes 1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
$19.99
RaceDayQuads FPV Cycle Toothpick 3 (TP3) 3" Micro Frame Kit
At its inception, the Toothpick formula was to turn a whoop inside out and give it the ability to perform like a much larger craft. Just a typical brushless AIO whoop board with similar motors but very large, very light 65mm(2.5in) props on a very light frame. The resulting performance was jaw dropping in any configuration from an AUW of ~37g on 1S to 73g on 2S and pure wackiness on 3S.The goal with the Toothpick project was first and foremost to be safe for almost any environment, fully legal, quiet, durable, reliable and most importantly, loads of fun! These features should not be compatible with each other but the magic of crazy disk loading and power radios made it possible.As with anything, the more you do it, the more developed and fine tuned your tools become. Like a surgeon that gets better at their craft and graduates to more and more developed instruments, the TP3 is literally a refined, purpose built, surgical instrument of the sky. If built to top end spec on 3S, this sucker is a frikin bullet! So throw that safety out the window. However the same setup on 2S becomes a very safe friend :-). Just as safe as the original Toothpick setup. The noise profile on 2S is significantly quieter than a 65mm/2.5” Toothpick twin blade on 2S. On 3S it’s still slightly quieter than a top power spec 65mm/2.5” Toothpick.The TP3 formula is similar to the original. Extremely low weight, large props for such a low weight and the smallest motor that can spin that prop with good control. The pudding is in the details however and we spent months intensely testing everything just to find out that what we’re looking for doesn’t exist! So we started making custom parts. There is a lot in how it’s setup as well but that’s better left to the video than writing pages on pages...Starting with the prop, we knew what we wanted but it didn’t exist. Having a good relationship with Gemfan, we carefully crafted a prop together and they got working on manufacturing. With the prop in mind, we then tested custom motor products from just about every known company out there before landing on a couple of gems...that only became good with numerous revisions. Other manufacturers will figure it out and give us more options in time but the two we have now are stellar. Given the crazy performance we were after, the frame also needed to be reimagined to perform and hold up to a new level of punishment. Next, we had to solve the annoyance with whoop boards and how difficult they were to solder. FullSpeed and BetaFPV were instrumental in the execution of the redesign and we now have two great options in case one runs into QC or reliability issues. The rest of the build is arbitrary but we prefer just a basic camera and Vtx to keep the weight down. Performance wise, this thing is FAST. FAST fast. There are probably other things in this size class that are faster in a straight line, but that's not what we mean by fast. It’s like flying a laser pointer, it just does EXACTLY what you want it to do with absolute precision. Throttle control is also exquisite. It's a bit difficult to explain all the performance in words but when you fly one, you'll understand. The performance profile on a low weight load out also fits a Betaflight stock tune with just a little more TPA.Durability is one area that may be in question and is where we need to put a little bit of a disclaimer on this style build. When built to top spec on 3S, this thing is VERY FAST and INSANELY AGILE. This build is designed for advanced pilots but it doesn’t mean that it’s weak or not for beginners. That’s actually far from true. The frame is quite robust, motors are quality built and even the prop shaft is beefed up. When you first learn to ski or snowboard, you fall. You fall a LOT. It hurts. As you improve, you learn how to fall. Pro level athletes do amazing things and also know how to fall amazingly well. As an FPV pilot, you learn how not to break your equipment….or, balls to the wall and you know you’re going to break it and are okay with it. To achieve this level of performance, high durability has been replaced with repairability. It definitely still takes quite a bit of force to break an arm. The extremely low weight means that if you’re a beginner and running 2S, it’ll be quite difficult to break. It really only becomes a hazard to itself when you're darting around at high speeds.This thing is so incredibly easy to fly with its low weight and incredible control, it’s exactly what the advanced pilot needs to push their own limits and exactly what the novice wants to learn on. Check out all our 2-3" Frame Kits and the rest of our FPVCycle Collection Features Multi Unit design T700 carbon in 0.5mm laminate thickness (thinner is better, typical is 1.5mm) ~9-10g built frame base with hardware (some variation) 1.5mm body plates, 2.5mm arms Accepts 1”x1” typical whoop mounting platform Good quality carbon but no chamfers to keep costs down Made to be used. Not a shelf ornament. Every line on this design is very delicately crafted for optimization Repairability when you smash it Skinnier arms for less thrust deflection and rotational drag Similar weight to a monobody of the same or lesser durability Cheaper to maintain Easier to repair and maintain Doesn’t ruin your flying day due to a crash Recommendations Under 109g AUW with 3S 450mah Under 95g on 2S 450mah No smaller or larger than 450mah cells in 3S or 2S Press fit props on a 2mm prop shaft motor No more than ~7g per motor NO TPU SHOES ON THE ARMS! Includes 1x FPV Cycle Toothpick 3 3" Frame - TP3
$17.99
RaceDayQuads BetaFPV VR03 5.8GHz FPV Goggles w/ DVR
Newly developed by BETAFPV, and based on VR02 FPV Goggles, the VR03 FPV Goggles take features of VR02 and come with a DVR recording function. This exciting function allows pilots to catch the memorably breathtaking moment, greatly heightening the FPV flying experience. Check out the rest of our BetaFPV products and selection of FPV Goggles and Accessories! Specifications Size: 130x145x90mm Weight: 300g (without straps) Video Format: NTSC/PAL Supported Channel: 48CH Screen Size: 4.3 inch Screen Resolution: 800x480 Battery: internal 3.7V, 2000mAh Working Time: About 2 hours (Normal mode)/1 hour 10 mins (Recording mode) Max Charging Current: 1A Antenna Port: RP-SMA (Whip Antenna included) Charging Port: Type-C Card Slot: Micro SD card (Not included), Supports FAT32 system, supports maximum 64GB storage. Class10 is recommended Record Resolution: 480P Record Format: AVI Includes 1x BetaFPV VR03 5.8GHz FPV Goggles w/ DVR
$69.99
RaceDayQuads BetaFPV Toothpick / Whoop Hardware Kit
These screws and rubber dampers are really useful for mounting your Whoop / Toothpick FC. Check all our whoop frames & accessories and the rest of our BetaFPV selection! Specifications M1.2* 4 screws fit for stock Blade Indcutrix frame / 65mm frames. M1.4* 5 screws fit for Eachine black E010 frame / 75mm / 85mm frames. Black rubber dampers has a gap of 0.8mm, suitable for ALL brushed FC boards. White rubber dampers has a gap of 1.2mm, suitable for 2S AIO FC boards, F405 FC stack etc. Blue rubber dampers has a gap of 1.8mm, suitable for 2-4S AIO FC boards. Includes 20x M1.2* 4 screws 20x M1.4* 5 screws 20x Black rubber dampers 20x White rubber dampers 20x Blue rubber dampers
$9.99
RaceDayQuads BetaFPV T Dipole 900MHz RC Antenna 2 Pack - Choose Length
Designed and manufactured by BETA FPV for any 900MHz receiver with IPEX 1 / U.FL connector, this omnidirectional antenna includes an RF balun circuit integrated inside the injected rubber enclosure. Every antenna is tested with a frequency spectrograph to ensure a perfect tune! Check out our RC Antennas and all our BetaFPV products! Specifications Coaxial Cable Length: 80mm or 46mm Antenna Width: 145mm or 60mm Gain: 2dBi VSWR: <1.6 Connector: IPEX MHF (IPEX 1 / U.FL) Weight: 0.94g Includes 2x BetaFPV T Dipole 900MHz RC Antennas
$6.99
RaceDayQuads BetaFPV SuperG True Diversity Dual 1 Watt Micro/Nano ELRS 2.4GHz RC Transmitter Module - Choose Your Color
Based on ELRS V3.3 and collaborated with ELRS developer team, the First Ever Gemini Dual-Frequency Diversity Transmitter comes out! At present, SuperG Nano Transmitter can be fully activated to achieve the best link quality ever combined with diversity rx such as SuperD receiver or SuperP receiver. With dual 1W transmit power, it excels in anti-interference performance and stability, making it the ideal solution for demanding applications like FPV racing, long-range flight, and professional photography. Check out our RC Transmitters and all our BetaFPV products! Features Introducing the pioneering Gemini Dual-Frequency Diversity Transmitter, propelling ELRS into the era of dual-frequency capabilities. Dual 1W transmit power experienced amplified signal strength, expanded transmission distances, and a substantial increase in remote control range. In conjunction with existing true diversity receivers, activating the Gemini mode ensures unwavering signal stability even in the most intricate radio environments. Meticulously crafted from CNC aluminum alloy, the transmitter casing facilitates efficient thermal conductivity, complemented by an intelligently designed Heatsink system for optimal heat dissipation. Featuring 2 customizable buttons and 1 USB port, the transmitter accommodates external power sources, enabling steadfast long-range expeditions. Diagram Below is the diagram for the SuperG Nano Transmitter. Note: Please assemble the antenna before powering on. Otherwise, the PA chip in the SuperG Nano Transmitter will be damaged permanently. The following is the comparison information of the 3 products SuperG Nano Transmitter, ELRS Nano TX Module and ELRS Micro TX Module. It shows the advancing updates and specifications more than ever. SuperG Nano TX Nano TX Micro TX Max RF Power Dual-1000mW 500mW 500mW/1000mW RF Chip Dual SX128x Single SX128x Single SX128x Antenna Mode Gemini Single Single Cooling System Supported Unsupported Supported Backpack Supported Unsupported Supported External Power Supply Supported 7-13V Unsupported Supported 5-12V Know More About Diversity&Gemini Antenna Diversity mode, two antennas. Switch the two antennas regularly to read the RSSI value of the signal and determine which antenna to use to receive data. True Diversity mode, where both antennas receive data at the same frequency, and the antenna that receives the correct data first is used. Gemini mode, where two antennas simultaneously receive telemetry data with a frequency difference of 40MHz. They also transmit data simultaneously but at different frequencies. This means that you can receive the same data packets on different frequencies and antennas. This mode provides stable flight even in complex radio environments. Among them, Gemini is the most advanced function yet of ExpressLRS - Gemini mode currently! It owns the most stable mode for receiving signals and offers higher resistance to interference and stability, making it suitable for various applications. SuperG Nano Transmitter features Gemini mode. In a testing video by developer Jye Smith, it is shown that with a refresh rate of 1000Hz, the LQ value fluctuates between 90-100 when the true diversity receiver is in operation. However, after switching to Gemini mode, the LQ value stabilizes at 99-100. This demonstrates that ELRS goes to great lengths to ensure link stability. Combination with Diversity RX Gemini mode is built upon the hardware foundation of true diversity receivers and requires a dual RF output high-frequency module. When used with Super series products, the advantages of Gemini mode can be fully utilized. And The effects of using the transmitter and receiver in various modes are as follows: TX RX Antenna Receiving Mode ANT1/ANT2/Switch Single Single Diversity Diversity Gemini Single Gemini Single Single Diversity Diversity Gemini Gemini Using it together with True Diversity Receiver ensures a super stable yet strong radio link for pilots to fly in any environment that require extremely stable signals and low latency. Including long-range flights, multiplayer flights, and FPV racing. It gives pilots a robust and aggressive flight experience. Dual 1W Output Power The SuperG Nano Transmitter with Dual-active Antennas@Dual Frequencies, each boasting a powerful 1W transmission power. Experience stronger signals, longer transmission distances, and enhanced remote control range. Cooling System Iteration The casing part is made of CNC aluminum alloy with an anodized surface for durability. It efficiently dissipates heat, thanks to its optimized internal airflow and high-speed fan with copper heat fins. Fly with confidence and enjoy reliable performance every time. Combination with Most Radio TX The SuperG Nano Transmitter could be configured via LUA script. EdgeTX and OpenTX radio transmitter that supports CRSF could be used easily. It available for popular Nano interface TX when used with Micro-Nano Module Adapter including Radiomaster TX16, Boxer, Zorro. Jumper T16, T20, T Pro. Frsky QX7, X9, X Lite. Note: LiteRadio 3 Pro Radio Transmitter cannot support dual transmitter power above 100mW due to power supply issues. Express Yourself in Vibrant Colors SuperG Nano Transmitter is a cutting-edge device that offers a distinct and personalized flair, with a range of three vibrant color options including red, grey, and black. The combination of its sleek design, superior functionality, and colorful choices perfectly caters to those who seek elevate style and performance. ELRS Series The ExpressLRS Series expands its lineup with the addition of SuperG Nano Transmitter. To achieve exceptional link quality, pair the Gemini TX with Super series diversity receivers. BETAFPV takes the flying experience to new heights by introducing ELRS links that offer long-range capabilities, low latency, and high refresh rates in a radio control system. Basic Configuration SuperG Nano Transmitter is designed to receive signals using the Crossfire Serial Data Protocol (CRSF). Therefore, the interface of the transmitter's high-frequency module needs to support CRSF signal output. Taking the EdgeTX transmitter system as an example, we will explain how to configure the transmitter to output CRSF signals and control the transmitter using Lua scripts. In the EdgeTX system, navigate to MODEL SEL and enter the SETUP menu. Disable Internal RF (set to OFF), enable External RF, and set the Output Mode to CRSF, as shown in the picture below. Lua scripting is a lightweight and compact scripting language that can be embedded in the transmitter for convenient access to and modification of the transmitter's configuration. Download the elrsV3.lua script from the BETAFPV Support Center or ExpressLRS Configurator. Copy the official Lua script, elrsV3.lua, to the SD card of the transmitter, under the path Scripts/Tools. On the EdgeTX system, long-press the SYS button or MENU button to access the SD-HC CARD menu. In this menu, select the elrsV3.Lua script and run it. If the Lua script runs successfully, the interface will appear as shown in the illustration below. Custom Buttons SuperG Nano Transmitter reserves 2 buttons that can be customized by users. Here are the specific steps to operate: Enable the transmitter's WiFi or power it on and wait for 60 seconds to enter WiFi mode using LUA programming. The RGB indicator light will slowly flash in green, indicating that the transmitter has automatically enabled WiFi (WiFi name: ExpressLRS TX, WiFi password: expresslrs). Connect your smartphone or computer to the WiFi network and open a web browser. Enter http://10.0.0.1 to access the custom button settings page. In the corresponding button's Action column, select the desired custom function. Then, choose the button type and the number of presses or duration in the Press and Count columns. Click SAVE to complete the settings. Currently, there are 6 available functions that can be assigned to shortcut buttons. There are 2 ways to use the buttons: long-press and short-press. The duration of a long press can be customized, while the number of presses for a short press can also be customized. The following are the 6 functions that can be set: Unused VTX Setting Increase Output Power Enable WiFi Enter VTX Channel Enter Binding Mode Enter VTX Band The pictures below show the functionality of the transmitter in its factory default settings. (The left button is Button1 and the right button is Button2). Button Action Press Count Button1(Left Button) Enter Binding Mode Short Press 3 Times Increase Power Long Press For 0.5 seconds Button2(Right Button) Go to VTX Channel Menu Short Press 2 Times Send VTX Settings Long Press For 0.5 seconds Note: This transmitter hardware does not support button RGB lights. Bind & External Power Supply The SuperG Nano Transmitter utilizes the default firmware, which employs the ExpressLRS V3.3.0 official protocol without a Binding Phrase. Consequently, the binding receiver should also be equipped with firmware V3.0.0 or higher and have no Binding Phrase set. For optimal performance, it is recommended to position the transmitter's two antennas as far apart as possible. Put the receiver in a bound state and wait for connection. Click the "Bind" in the Lua script or the set custom button to enter the binding mode. If the Indicator has turned solid, it indicates that the device has been bound successfully. Note: If the firmware of the TX is reflashed and the Binding Phrase is configured, you cannot enter the Binding state through the above method. Please set the RX to the same frequency Binding Phrase, and the TX and RX can be connected automatically. When the dual transmit power exceeds 500mW, the SuperG Nano Transmitter exhibits relatively high power consumption, leading to a reduced battery life. To prolong the transmitter's usage time, it is advisable to utilize an external battery as a power source. The power consumption of the transmitter is not only related to the transmit power but also to the telemetry ratio. When using high power of 500mW and above, the return ratio can be set higher to reduce power consumption and extend use time. For example, in Gemini mode, the power consumption of setting the return ratio to 1:128 is 1000mA, while the power consumption of setting the return ratio to 1:2 is only half of 1:128. Note: When the voltage of the radio transmitter battery or external battery is lower than 7V (2S) or 10.5V (3S), please use the Gemini mode of 500mW and 1W carefully, otherwise the transmitter will enter the restart state due to insufficient power supply, resulting in disconnection out of control. FAQ When establishing a link, it is not possible to enter the LUA script. The ELRS LUA script version is outdated and requires an upgrade to elrsV3.lua. The baud rate of the radio transmitter is set below 400K, and it should be adjusted to a value above that. If there is no option to modify the baud rate, it is necessary to update the radio transmitter firmware, ensuring that EdgeTX is at version V2.7.0 or newer. If your radio transmitter is unable to use the F1000 Packet rate or prompts "Baud rate is too low". Reason: F1000 requires a baud rate higher than 400K, and the radio transmitter's baud rate is 400K by default. Solution: First update the baud rate (greater than 400K) setting in the Hardware from the Model Setup menu or System menu, then restart the radio transmitter to ensure the baud rate setting has been applied. Then change the Packet rate. When the F1000 is turned on, the Packet rate between the radio transmitter and the SuperG Nano Transmitter is less than 1000. Reason: EdgeTX version problem Solution: The EdgeTX version needs to be upgraded to 2.8.0 or above. And the LiteRadio 3 Pro Radio Transmitter defaults to EdgeTX 2.8.0 and does not have this problem. The SuperG Nano Transmitter's default firmware is ELRS V3.3.0, and users need to update the receiver to V3.0.0 or above to bind the frequency. Download the Instruction Manual for the SuperG Nano Transmitter Download the firmware for the SuperG Nano Transmitter Download the Backpack firmware for the SuperG Nano Transmitter Download the STL File for the SuperG Nano TX Insulated shell Specification Item: BETAFPV SuperG Nano Transmitter Module | ELRS 2.4G Weight: 44.8g Color: Black, Red, Grey Antenna Connector: 2x RP-SMA RF Power: 25mw/50mW/100mW/250mW/500mW/1000mW Packet Rate: 50Hz/100Hz/150Hz/250Hz/333Hz/500Hz/D250/D500/F500/F1000 Frequency Band: 2.4GHz ISM Backpack: support Input Voltage: 7V~13V DC Rated Current: 8V,1000mA@1000mW, 1:128, Gemini mode USB Port: Type-C Fan Voltage: 5V Default Firmware Version: ExpressLRS V3.3.0 Target Name: BETAFPV SuperG Nano 2.4GHz TX Includes 1x SuperG Nano Transmitter (Black/Red/Grey) 2x 2.4G Glue Stick Antenna 1x USB to Type-C Data Cable 1x Type-C Male to XT30U Male Power Cable 1x GH1.25 Male to FUTABA Male Signal Cable 1x Micro-Nano Module Adapter (Standard Version) 1x Double Side EVA Foam Tape 1x Instruction Manual 1x Service Card
$69.99
RaceDayQuads BetaFPV SuperD ELRS Diversity 2.4GHz Receiver
BETAFPV SuperD ELRS 2.4G is the world's first True Diversity Receiver that applies two antennas, dual receiver chains, and TCXO (temperature compensated crystal oscillator) tech, achieving super accurate frequency rate and excellent performance in extreme temperature environments. It greatly fulfills the requirements of reliability for long range flying, aerial photography, or FPV freestyle tricks Check out all our receivers, and our entire BetaFPV selection! Specifications Item: BETAFPV SuperD ELRS 2.4G Diversity Receiver MCU: ESP32 PICO D4, dual SX1280 (SX1281) Antenna Connector: IPEX MHF 1/U.FL RF Frequency: 2.4GHz (2400~2480MHz) Telemetry Power: 20dBm (100mW) Receiver Protocol: CRSF Input Voltage: +5V DC @ “+” pad PCB Size: 22mm*14mm Weight: 1.1g excluding antenna Includes 1x SuperD ELRS 2.4G Diversity Receiver 2x BETAFPV Dipole T Antenna 1x Pin Header 1x 30AWG Silicon Wires (1 black, 1 red, 1 white, 1 yellow) 1x User Manual
$21.99
RaceDayQuads BetaFPV T Dipole 2.4GHz RC Antenna 2 Pack - Choose Length
Designed and manufactured by BETA FPV for any 2.4GHz receiver with IPEX 1 / U.FL connector, this omnidirectional antenna includes an RF balun circuit integrated inside the injected rubber enclosure. Every antenna is tested with a frequency spectrograph to ensure a perfect tune! Check out our RC Antennas and all our BetaFPV products! Specifications Coaxial Cable Length: 80mm or 46mm Antenna Width: 60mm Gain: 2dBi VSWR: <1.4 Connector: IPEX MHF (IPEX 1 / U.FL) Weight: 0.94g Includes 2x BetaFPV T Dipole 2.4GHz RC Antenna
$6.99
RaceDayQuads BetaFPV Storage Case for 65/75mm Micro Drone
This case is designed for carrying a 65-75mm drone, it is made of EVA material, which is sturdy, durable and waterproof(except zipper part). Come with ample space for storing canopy, props, chargers, and batteries, etc. With this case, you're ready to grab your gear and go flying whenever you want, without having to carry around a bunch of different containers. Check out all our whoop gear and our BetaFPV selection! Features Come with a sturdy and durable EVA material, this case is water-proof(except zipper part) and resistant to impact damage. Ample space for storing the canopies, props, chargers, and batteries, etc. Built-in grid space, easy to store the small accessories. Wide-applicability, this case can not only suit for BETAFPV Meteor series/65X/65S and other whoop drones, it is also suitable for most brands 65/75mm FPV drones. Come with an exquisite gift, specially offered some cool stickers, more fun for FPV flight. Specifications Color: Black Weight: 100g Size: 12*12*7mm Material: EVA Includes 1x BetaFPV Storage Case for 65/75mm Micro Drone
$11.99
RaceDayQuads BetaFPV Storage Case for LiteRadio
This case is designed for carrying a Beta FPV LiteRadio series transmitter, it is made of EVA material, which is sturdy, durable, and waterproof (except the zipper part). Comes with ample space for storing transmitter, module, antenna, and strap lanyard, etc. With this case, you're ready to grab your gear and go flying whenever you want, without having to carry around a bunch of different containers. Check out the rest of our transmitters, parts & accessories, and our BetaFPV selection! Features Ample space for storing the transmitter, module, antenna, and strap lanyard Built-in grid space, easy to store the small accessories Comes with foam liner inside, this liner is removable Includes 1x BetaFPV Storage Case for LiteRadio
$19.99
RaceDayQuads BetaFPV RTF Cetus FPV Analog Kit - Cetus Whoop, Goggles, Transmitter, Batteries, Charger & Case
All batteries must be shipped by a ground shipping method. Brush up on your FPV skills with the BetaFPV RTF Cetus FPV Kit - Cetus Whoop, Goggles, Transmitter, Batteries, Charger & Case. You have everything needed to get into FPV, including the LiteRadio 2 SE Transmitter, VR02 FPV Goggles, and the Cetus Whoop. Easy to carry on and ready to fly. What are you waiting for? Be sure to pick up some extra batteries so that you can fly all day! We recommend the following 1S batteries for this quad: BetaFPV 1S 300mAh - BT2.0 Check out our other RTF combos, all our pre-built quads and our BetaFPV selection! Features 3 Flight modes Altitude hold and emergency landing functions Storage case FrSky D8 protocol drone and radio Brushed drone, easy to fly Specifications Positioning system: Optical flow / Barometer / Laser Height Positioning: Laser / Barometer Angle Locating: Optical flow ( effective height 0.3-3m) Accuracy of auto-hover: Horizontal ±0.2m, vertical ±0.3m (under no wind environment) Receiver protocol: Frsky D8 Flight controller: Lite 1S Pro brushed FC VTX: 25mW Camera tilt degree: 25° Camera: C01 FPV Micro Camera Transmitter: Literadio2 SE Transmitter TX mode: Mode 2 (Left stick throttle) Goggles: VR02 Goggles Motor: 716-19000KV Brushed motor Propeller: 31mm 4-blade 0.8mm shaft hole Takeoff weight: 35g(with battery) Power system: 1S Battery: BT2.0 300mah 1S Battery (external) Flight time: 4-5min Flight distance: 80m (Clear line of site) Includes 1x Cetus Brushed Quadcopter 1 LiteRadio2 SE Transmitter (Frsky D8 Protocol) 1x VR02 FPV Goggles 2x BT2.0 300mAh 1S Lipo Battery 1x BT2.0 Battery Charger and Voltage Tester 1x USB Charging Cable (Type-C) 1x Type-C Adapter 1x Prop Removal Tool 4x 31mm 4-Blade Props 1x Portable Storage Bag User Manual
$159.99
RaceDayQuads BetaFPV RTF Cetus X FPV Analog Kit - Cetus Whoop, Goggles, Transmitter, Batteries, Charger & Case
All batteries must be shipped by a ground shipping method. Whether you're a skillful pilot or a new beginner, the Cetus X FPV Kit is an advanced 2S power whoop bundle, and a primary choice to reach a higher stage. From its unparalleled control to its exciting flying that has you immersed your experience through every FPV flight, there is simply nothing like Cetus X FPV Kit. With the combination of Cetus X Brushless Quadcopter, LiteRadio 3 Radio Transmitter, and VR03 FPV Goggles, get ready for the next level of flying FPV. Be sure to pick up some extra batteries so that you can fly all day! We recommend the following 1S batteries for this quad: BetaFPV 1S 300mAh - BT2.0 Check out our other RTF combos, all our pre-built quads, and our BetaFPV selection! Features Nothing quite beats the experience of flying Cetus X with an enhanced propulsion system, and longer radio and video transmission. With a very functional and potential remote controller and FPV goggles, pilots can unlock more accomplishments to the next level. Two FC versions are offered for pilots. With the support of the Betaflight configurator, beginners can learn quadcopter configuration through the Betaflight FC version. For pilots who prefer the classical Cetus, the Cetus FC version with an altitude hold function is also coming soon. Classical white design inherited from Cetus Series and made of PA12 material, the Cetus X frame has an excellent impact resistance in drop & impact and reduces the risk of damage, giving you more peace of mind. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots. LiteRadio 3 reserves a nano bay that supports the external TX module for the compatibility of more quadcopters. And the VR03 FPV goggles which are newly added a Micro SD card slot to save the video with DVR recording, support most Analog VTXs in the market. The quadcopter, radio transmitter, FPV goggles, and all of the accessories are packed in an EVA portable storage bag. It is convenient to carry outside and better to protect the equipment. Powerful Propulsion System Equipped with 1103 11000KV Brushless Motors and Gemfan 2020 4-blade props, the Cetus X Brushless Quadcopter delivers powerful propulsion, making it a 2S power whoop drone with some real punch to it. The whole quadcopter is light and durable enough, offering pilots a high-efficiency flight experience. Recording Every Flight Moment Newly developed by BETAFPV, and based on VR02 FPV Goggles, the VR03 FPV Goggles take features of VR02 and come with a DVR recording function. Pilots can enjoy the playback saved through the goggles or export the videos by Micro SD card. This exciting function allows pilots to catch the memorably breathtaking moment, greatly heightening the FPV flying experience. Improved Video Transmission Cetus X Brushless Quadcopter comes with M04 25-400mW VTX and C04 FPV camera. M04 25-450mW VTX features a lightweight and adjustable output power for long-distance flying. Combining this VTX and the excellent radio link ExpressLRS 2.4G, pilots can fly whoop drones longer to explore more possibilities and have fun. In addition, the C04 FPV camera (based on Caddx Nano Ant Camera/Runcam Nano 4) shows better quality in FPV flight compared with the C02 FPV camera. LiteRadio 3 Radio Transmitter This transmitter features an ergonomically designed handle and has superb performance in its working time, a newly updated gimbal. Besides, this version supports BETAFPV Configurator, which is a utility designed to simply update, configure, and tune the radio controller. Experience the thrill of total immersion with unrivaled control and capture the world around you. FPV Simulator Supported First time flying a quadcopter? You can learn and practice flying a quadcopter through an FPV simulator before real flying. LiteRadio 1 supports playing FPV simulators like DRL/DCL/Uncrashed/Liftoff. LiteRadio 1 is capable of practicing and charging at the same time. Check out the Liftoff flying demonstration here. Download Liftoff here. Various Modes, Accessible to All Cetus X supports Angle/Horizon/Air Modes, which can satisfy the different needs of pilots and adapt to various flight environments. When the quadcopter falls to the ground and upside down, you can activate turtle mode by LiteRadio 3 transmitter to flip it over and resume flying. Whether you're a seasoned FPV pilot or a complete beginner, the Cetus X FPV Kit helps anyone fly confidently from day one. BETAFPV Cetus Series The BETAFPV Cetus Series has been very popular since its release in 2021 and become the primary FPV choice for new beginners. Whether propulsion system, radio transmitter, VTX range, or other functions, BETAFPV never stops step to make the product better. From the initial Cetus to Cetus X so far, Cetus Series always satisfies customers' needs no matter new beginners or seasoned pilots. Specification Item: Cetus X FPV Kit Weight: 55g Wheelbase: 95mm FC: F4 1S 12A FC Motors: 1103 11000KV Motor Props: Gemfan 2020 4-Blades Props Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4) Camera Adjustable Angle: 0°-40° Receiver Protocol: ELRS 2.4G (Betaflight)/Frsky D8 (Cetus) VTX: M04 25-400mW VTX Quadcopter: Cetus X Brushless Quadcopter Transmitter: LiteRadio 3 Radio Transmitter Goggles: VR03 FPV Goggles Battery: 2x BT2.0 450mAh 1S 30C Battery Flight time: 5 mins Includes 1x Cetus X Brushless Quadcopter (Betaflight Firmware, ELRS 2.4G Receiver) 1x LiteRadio 3 Transmitter (ELRS 2.4G) 1x BETAFPV VR03 FPV Goggles 4x BT2.0 450 mAh 1S Lipo Battery 1x BT2.0 Battery Charger and Voltage Tester 1x USB Charging Cable (Type-C) 1x Type-C to FC Adapter 1x Prop Removal Tool 4x Gemfan 2020 4-Blades Prop (Spare Set) 1x Portable Storage Bag FAQ For more info and instructions, please check the User Manual for Cetus X FPV Kit. Please DO NOT configure ESC or Motor settings on the Betaflight configurator. The VR03 FPV goggles do not include a Micro SD card. You should prepare it before using the DVR recording function. The External TX module for LiteRadio 3 should be bought separately. Recommend BETAFPV Nano TX Module.
$289.99
RaceDayQuads BetaFPV Replacement Shell for ELRS Micro TX - Choose Color
Did you crack the case or simply want to change the look of your BetaFPV ExpressLRS Micro TX? Now you can with this white replacement shell! Check out our Express LRS collection and all our BetaFPV products! Features Made of high-quality plastic material. It is very durable and stable Upgraded case designed. The USB port size is 6.5*13.5mm, which is compatible with 90% of the known USB Type-C cables Specifications Case Weight: 20g USB Port Dimensions: 6.5*13.5mm USB Port: Type-C Includes 1x BetaFPV Replacement Shell for ELRS Micro TX
$3.99
RaceDayQuads BetaFPV Pavo25 Cinewhoop 2.5" Micro Frame Without Carbon - Choose Color
The Pavo25 frame in a multitude of colors to transform your Pavo25 to be your own!! Check out all of our frames, and the rest of our BetaFPV gear! Features With the insert copper nut design on the main screw holes, only 6 screws are enough to assemble the whoop duct and drone, which is convenient to build. The Pavo25 frame sports a reasonable structure assembly design that is optimized to decrease complex components, making the build easy. Made of high-quality PA12 material and 2.5mm carbon fiber. With a strong and durable frame kit, the Pavo25 frame optimizes the vibration damping structure for the camera mount, allowing pilots to get an excellent experience. An innovative pusher frame with a duct design. It generates more lift for the whole quadcopter, improving the ability of endurance and propulsion. Equipped with a CNC Vista Adapter. It effectively provides the Caddx Vista HD Digital VTX with a good cool down by increasing the heat dissipation area, reducing the influence of heat on VTX. Specifications tem: Pavo25 Frame Kit Wheelbase: 108mm Color: Black/Transparent Grey/Yellow/Blue/Purple Material: PA12 Frame Color: Black, grey, yellow, blue, purple Weight:31.5g (without carbon fiber) Body Size: 153.2x153.7mm (without EVA adhesive foam) Top plate thickness: 2.5mm Propeller size: 2.5-inch FC pattern: 25.5x25.5mm FPV cam spacing:14mm Includes 1x BetaFPV Pavo25 2.5" Cinewhoop Frame Without Carbon
$8.99
RaceDayQuads BetaFPV Pavo Pico HD 81mm Cinewhoop Frame (HD Digital Version) - Black
Pavo Pico is the tiniest 2S Sub100g DJI O3 Cinewhoop frame, working with other popular HD digital VTX such as Walksnail Avatar Pro Kit, Vista Kit, etc. After testing with pilots, this frame has been upgraded by lowering the battery slot height and adding filters and camera protection parts. These updates enhance the camera and HD digital VTX, to give pilots an unparalleled flying experience. The Pavo Pico is an all-new HD 81mm cinewhoop with 45mm props that is designed to be the smallest 2S-3S, sub100g build. Check out the rest of our micro frames and the rest of our BetaFPV gear! Features HD digital VTX bracket made of lightweight and tough injection-molded PP material with an adjusted structure to prevent HD VTX displacement or loss after the crash. Incorporating an angle-limited lens protection print and DJI O3 series filters, It is recommended to purchase, which can increase safety and improve visual quality. The Rubber Damper Vibration damping design reduces low-frequency vibrations and is used with GyroFlow stabilization software for a stable and clear camera image during high-speed flight. To accommodate a wider range of battery sizes, the main body of the frame can be trimmed through DIY methods. Additionally, larger batteries can be installed by using battery straps or printed components. The DJI O3 can be directly installed, while Avatar and Vista require a 20x20 mounting plate and screws (included) for fixation. The naked frame is suitable for users who DIY refit and assemble the HD VTX by themselves. We offer a wider range of colors for the Pavo Pico frames, giving you even more options to choose from. Whether you prefer a bold and bright hue or a more subdued shade, we have a color that will suit your style. You can choose your favorite color or collect them all to create your own unique mix-and-match cinewhoop. Pavo Pico Frame Kit We used ultra-light PP material to make the HD VTX mounting bracket, increasing its toughness. The antenna fixing slot and frame have been fused to reduce damage risk, while the camera's installation height has been lowered with a protective printed part to limit its movable angle to within 30°. Additionally, an O3 filter can be used to protect the lens and enhance image quality. We have incorporated a unique rubber damper vibration-damping design, used with GyroFlow stabilization software, which greatly enhances safety and ensures a smooth, HD image output. When you screw the die-cast screws, please DO NOT screw them too tight to leave room for rubber dampers to absorb vibration. It may cause jello in the video footage. Click to watch the installation guide video for DJI O3 Air Unit on Pavo Pico. And The whoop quadcopter package includes the DJI O3 HD Digital VTX Antenna Mount. DJI O3 Vibration Problem To tackle the challenge of vibration on many whoop drones, the DJI O3 unit is mounted on a carbon fiber plate with 4 rubber dampers. This innovative design ensures peak performance and perfect stability. Troubleshooting To improve video quality when recording with DJI O3 HD VTX, turn off its electronic stabilization and use GyroFlow stabilization software. When fixing the HD VTX bracket with M1.4*10 screws, ensure that the nut just touches the shock-absorbing ball. The Jello effect may occur during the above installation due to 2 reasons: The VTX bracket is over-tightened with the screw and the rubber dumper is totally deformed. To solve this, make sure that the screw is tightened just enough to touch the shock-absorbing ball and keep the ball and bracket loose. If It is a large deformation of the frame or quadcopter blades, replace the frame or blades with larger vibrations if necessary. Note: use acetate tape to bind motor wires and prevent them from drooping and interfering with the propeller's rotation. Upgrade Low Profile Design After collecting feedback through the BETA TEST, we lowered the height of the HD VTX mounting bracket and whoop duct from 60.6mm to 51.5mm and the battery compartment results in a more low profile on the cinewhoop. Pilots can further customize their cinewhoop with DIY options such as battery straps or printable components, allowing for compatibility with a variety of battery sizes. This enables pilots to tailor and enhance their cinewhoop to meet their specific requirements and preferences. Steps as follow: Specification Item: Pavo Pico Brushless Whoop Frame Material: PA12 Wheelbase: 80.8mm Battery Slot Size: 16mmx12.7mm Camera Installation Spacing: 19mm/20mm Color: Black Weight: 11.62g Motor Mounting Hole Position: 3-M1.4-φ6.6mm FC Pattern: 26×26mm, suitable for F4 1S 12A AIO Brushless FC V3 Includes 1x BetaFPV Pavo Pico HD 81mm Cinewhoop Frame (HD Digital Version) - Black
$8.99
RaceDayQuads BetaFPV Micro Bay to Nano Module Adapter
Both the full adapter and PCBA only are Beta FPV's most recently updated versions. With the use of micro to nano module adapter, a nano tx module can work on transmitters with JR module bay (aka Micro module port) easily! The Micro to Nano Module Adapter (PCBA) is available for those who can print the case for themselves. You can download the adapter case STL file on Beta FPV's technical support page. This adapter is a perfect match for the BetaFPV Nano ELRS module in either 900MHz or 2.4GHz! Check out our RC Transmitters and all our BetaFPV products! Specifications Input: JR module bay (Micro module bay) Output: Nano module bay (Lite module bay) Supported Radio Transmitters: Frsky X9D/X9D Plus/X12S/X10/X10S/X7/X7S, Flysky TH9X, Turnigy 9XR/9XR PRO, FUTABA 16IZ, Jumper T16/T18/T18 Pro, Radiomaster TX16S/TX18S, TBS Mambo Supported TX Modules: BETAFPV Nano TX Module, TBS Crossfire Nano TX、Frsky XJT Lite/R9M Lite/R9M Lite Pro. Dimensions: 65x48x28mm Weight: 24.8g Includes 1x Micro-Nano Module Adapter or PCBA 1x Converter cable
$3.49
RaceDayQuads BetaFPV Micro 2022 Toothpick/Whoop Canopy - Choose Your Color
The BETAFPV Micro 2022 Canopy comes with a new injection molding technique that brings durability and flexibility to the canopy, which is a great choice for micro cameras with 20° or 30° lenses. The hollow-out design help reduces the influence of heat on electronic parts and this canopy is suitable for BETAFPV Meteor Series. Check out all our whoop frames & accessories and our BetaFPV gear! Features Made with injection molding, this canopy is more durable, anti-scratch and heat-resistant, providing good protection for your electronics. Best replacement for the old generation of canopy on all whoop drones with micro cameras. Thoughtful designs for 1/3'' lens camera like C02 Pro camera and 1/4'' lens camera like C02 camera, compatible with all whoop frames like Beta65S frame, Beta65S Lite frame, Beta85 Pro 2 frame, Meteor65 frame and Meteor75 frame Light weight 1.60g (with camera mount) / 1.93g (with decorations). And 6 colors in White/Black/Blue/Pink/Green/Orange Specifications Material: PP Tilt: 20/30° Weight: 1.60g (with camera mount) / 1.93g (with decorations) Color: Black/White/Blue/Orange/Pink/Cyan BetFPV Compatible Frames: Beta65S/Meteor65/ Meteor75 Includes 1 x Micro Canopy 2022 (Black/White/Blue/Orange/Pink/Cyan) 1 x 20° Lens Camera Mount for C02 1 x 20° Lens Camera Mount 1 x 30° Lens Camera Mount 3 x Decorative Parts 4 x M1.4x3 Screws 4 x M1.4x4 Screws
$3.99
RaceDayQuads BetaFPV Meteor75 Pro Whoop Frame - Choose Your Color
Be bold and brave with the BetaFPV Meteor75 Pro Whoop Frame! Choose from seven vibrant colors. Meteor75 Pro is durable, lightweight (7.73g) and the motor holder is strong for stable flying. Uses 1102/0802SE Triangle mount motors and accommodates a larger 1S batteries. Perfect for 45mm props; increases thrust for 1S whoops, with HD digital VTX. Check out all our whoop frames & accessories and all our BetaFPV gear! Features Meteor75 Pro Brushless Whoop Frame is durable enough with a lightweight of 7.73g. The motor holder utilizes a triangle bilateral stretch structure, extremely strong for motor installation. So flying is stable when the quadcopter is at high speed. Recommend motors with triangle mount like 1102, 0802 Brushless Motors. The battery slot is bigger. Pilots can use a larger 1S battery with more capacity. Recommend BETAFPV 450mAh 1S Battery The frame is perfect for 45mm propellers. It greatly enhances the thrust for 1S whoop, especially when carrying HD digital VTX. Specification Item: Meteor75 Pro Brushless Whoop Frame Material: PP Wheelbase: 80.8mm Weight: 7.73g Color: Black/Blue/Cyan/Yellow/Orange/White/Red Motor mounting hole: 3-M1.4-φ6.6mm, 1102, 0802 Brushless Motors FC mounting hole: 26x26mm, F4 1S 5A FC Includes 1x BetaFPV Meteor75 Pro Whoop Frame - Choose Your Color
$4.99
RaceDayQuads BetaFPV Micro Whoop Canopy for HD Camera - Choose Color
This micro canopy is specially designed for Walksnail Avatar Nano camera, Runcam Nano Lite Camera, or most 14mm nano cameras, supporting an adjustable camera lens of 0-45°. It features high compatibility for both HD Digital VTX and Analog VTX like M03 Analog VTX. Features The canopy is designed with camera mounting holes for an adjustable camera lens of 0-45°. It is suitable for Walksnail Avatar Nano camera, Runcam Nano Lite Camera, or most 14mm nano cameras. Lightweight and two colors for options (Black/Blue). Using it with Meteor Series colorful frame will be more attractive. Recommend frames for Meteor65 Pro, Meteor75, and Meteor85 Adopt with injection molding technique, this canopy is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone. Unique design with three decorative parts like a knight, the drone flies in the air like a scientific spaceship cruising, making it very cool and special. Also, the decorative parts are detachable for better heat dissipation. Mounting Diagram The picture below is the diagram for this canopy. This canopy is applied to 1S Walksnail Avatar Mini HD VTX, HDZero Whoop Lite Bundle, M03 Analog VTX, or most 14mm nano cameras. Other brands' VTXs with similar sizes are available to be mounted on this canopy. Specification Item: Micro Canopy for HD Camera Material: PP Tilt: 0-45° Weight: 2.50g (without decorations), 3.28g (with decorations) Color: Black/Blue Adapted VTX: 1S Walksnail Avatar Mini HD VTX, HDZero Whoop Lite Bundle, M03 25-350mW 5.8G VTX Adapted FPV Camera: Walksnail Avatar Nano Camera, Runcam Nano Lite Camera, or most 14mm nano cameras Adapted Frame: Meteor65 Pro/Meteor75/Meteor85 Includes 1x Micro Canopy for HD Camera (Black/Blue) 3x Decorative Parts 3x M1.4x3 Screws 8x M1.4x5 Screws 3x M2x4 Screws Note: The decorative parts for both Micro Canopy for HD Camera and Canopy for Micro Camera 2022 are unavailable in common use even though they have a similar appearance.
$4.99
RaceDayQuads BetaFPV Micro Air Whoop Canopy - Choose Your Color
To elevate the flying experience, DIY enthusiasts have consistently prioritized the reduction of weight for the attainment of ultra-light structure for 1S whoop drones. Consequently, we have devised an exceedingly light Micro Air Canopy, weighing a mere 0.74g, that not only facilitates camera angle adjustment from 25° to 50° but also has antenna mounts, incorporated at the tail. If your goal is to optimize canopy functionality while minimizing weight to obtain a Sub18g 65mm Whoop, this option stands as the definitive choice. Check out all our whoop frames & accessories and our BetaFPV gear! Features With a mere weight of 0.74g, the canopy boasts a simplistic yet durable structure, ensuring effortless installation. It stands as the premier pick for ultra-light small whoop drones. This hollow-out design reshape the installation space and accommodates an assortment of Micro and Nano-sized Analog and HD Digital cameras that are widely sought after in the market. Positioned at the canopy's tail, reserved 4 antenna mounts enable seamless adjustment of the camera angle, offering a versatile range spanning from 25° to 50°, capturing the optimal image. More Compatibility Micro Air Canopy is the ideal option for constructing or enhancing ultra-light whoop drones featuring HD Digital VTX or Analog VTX, owing to its exceptional compatibility. This hollow-out design reshape the installation space and accommodates an assortment of Micro and Nano Analog and HD Digital cameras. So Micro Air Canopy provides full support for the C03 Camera, C02 Camera, Avatar HD Lite Camera, ANT Lite Camera, and other cameras possessing a lens diameter of 9-10mm. Infinite Personalization We provide diverse color options for the Micro Air Canopy, enabling greater freedom for personality. This allows for aligning or color clashing the canopy color with your drone's theme. And equipped with our various colors of Meteor65 Air Brushless Whoop Frame adds flexibility, and agility during flight. Your drone will capture people's attention and showcase your unique personality and creativity. Specifications Item: Micro Air Canopy Material: PP Tilt: 25°~50° (Adjustable) Weight: 0.74g (Including one Camera Fixed Screw) Color: Black, White, Transparent White, Transparent Blue, Transparent Purple, Transparent Green Includes 1x BetaFPV Micro Air Whoop Canopy - Choose Your Color
$2.99
RaceDayQuads BetaFPV Meteor75 Whoop Frame - Choose Color
Brand new lightweight 75mm 1S brushless frame for Meteor75 Brushless Whoop Quadcopter is released now! This frame is ultralight only 5.68g, but it still durable. Check out all our whoop frames & accessories and all our BetaFPV gear! Features Meteor75 frame is ultralight only 5.68g, light but durable enough. The motor mount position uses a quadrilateral stretch structure, the frame is more durable and stable. The height of the frame has been adjusted, the lowest point of the frame is the motor position, the battery can be protected while the drone is landing. It also increased the height of the frame loop to protect the propeller better. Designed two different motor mounting holes that support 0603, 0802 and 1102 brushless motors at the same time. With a 26mm*26mm FC mounting columns can match whoop style FC. Specification Material: Plastic Size: 75mm Weight: 5.68/pc Motor mounting hole: For 0603 motor, 1102 Series Motors and 0802 Series Motors FC mounting hole: 26mm x 26mm, fully compatible with whoop style FC board mounting pattern Includes 1x BetaFPV Meteor75 Whoop Frame
$4.99
RaceDayQuads BetaFPV Meteor85 Brushless Whoop Frame - Choose Color
This frame is customized for 85mm whoop drone and the frame for Meteor85, Meteor85 HD Digital VTX. With a marvelous design on the battery slot which keeps a low profile and triangle bilateral stretch structure of motor mounting position, this frame weighs only 11.32g. Features The new design frame reserves a battery slot, making it conveniently free from the battery strap and perfect for BETAFPV 450mAh 2S battery compared to the previous 85mm whoop frame. With the low profile of battery slot height, the drone's gravity center is reduced, and improved the sense of being compact. Meteor85 frame’s motor mounting position uses a triangle bilateral stretch structure, making the frame more aesthetic. It provides you more durable and smoother flight experience. The ultra-light and durable frame is PP material only 11.32g, which can match the F4 1-2S 12A AIO Brushless Flight Controller. The frame is suitable for 2" propellers. Recommend using BETAFPV canopy for nano HD camera, which is suitable for Caddx ant camera, or other nano cameras. It can also match the lighter BETAFPV canopy for a micro camera and install with a C02 Camera, C03 Camera, and M03 5.8G VTX. Specification Material: PP Wheelbase: 87.7mm Motor mounting hole: 110x motors, such as 1103 11000KV motors FC mounting hole: fully compatible with whoop style FC board mounting pattern, 26mm x 26mm Weight: 11.32g Includes 1x Meteor85 Brushless Whoop Frame (Grey or Black)
$5.99
RaceDayQuads BetaFPV Meteor65 Whoop Frame - Choose Your Color
Spare replacement part for the BetaFPV Meteor65 Whoop. Check out all our Meteor65 parts & accessories, the rest of our whoop frames & accessories and all our BetaFPV gear! Features Compared to previous 65mm brushless frames, with the low profile of battery slot height, the drone's gravity center is reduced and improved the sense of compactness. Meteor65 1S brushless frame’s motor mounting position uses triangle bilateral stretch structure, makes frame more aesthetic. It provides you more durable and smoother flight experience. The ultra-light and durable frame is PP material only 3.14g, which is one of the lightest frames with 26mm*26mm FC mounting columns can match whoop style flight controller. The material of 31mm 3-blade props is PC plastic with the 1.0mm shaft inner diameter. Suitable for 0603 and 080X series brushless motors. Specifications Item: Meteor65 frame Material: PP Size: 65mm Weight: 3.14/pc Color: Transparent/Blue/Black/Green/Pink/Orange Motor mounting hole: For 0603 motor and 080X Series Motors FC mounting hole: 26mm x 26mm, fully compatible with whoop style FC board mounting pattern Upgrade With the low profile of battery slot height, the drone's gravity center is reduced and improved the sense of compactness. Using triangle bilateral stretch structure, makes frame more aesthetic. Lightest frame weights 3.14g only, with 26mm*26mm FC mounting columns can match whoop style flight controller. Includes 1x BetaFPV Meteor65 Whoop Frame
$4.99
RaceDayQuads BetaFPV Meteor65 Pro Whoop Frame - Choose Your Color
Choose Between green and black for your whoop frame! Spare replacement part for the BetaFPV Meteor65 Pro Whoop. Check out all our Meteor65 parts & accessories, the rest of our whoop frames & accessories and all our BetaFPV gear! Features The space for the FC board is limited in order to support 35mm propellers on a 65mm drone. This Meteor65 Pro frame can only support cross shaped FC boards. The normal whoop FC board DO NOT fit this frame. Meteor65 Pro frame’s motor mounting position uses a triangle bilateral stretch structure, making the frame more aesthetic. It also provides you with a more durable and smoother flight experience The frame is suitable for 31-35mm propeller like Gemfan 35mm-3 propellers. Pay attention, HQ 35mm props are a little bit bigger and DO NOT fit this frame. Specifications Material: PP Wheelbase: 65mm Prop Size: 31-35mm FC Mounting: 26x26mm Cross Shaped AIOs Motor Mounting: 6.6mm Weight: 3.2g Includes 1x BetaFPV Meteor65 Pro Whoop Frame
$4.99
RaceDayQuads BetaFPV LiteRadio 2 SE RC Transmitter 2.4GHz - FRSKY D8/D16
All products with batteries must be shipped by a ground shipping method. After the latest round of beta testing, the LiteRadio 2 SE is back to the market with huge improvements. This pint size FRSKY radio is powered by OpenTX firmware and can toggle between FRSKY D16 and D8 protocols. Real gimbals provide the tactile feedback of a pricier radio and USB connectivity can be used to play FPV simulators on a computer. The LiteRadio 2 SE is a great option for anyone looking for a lower cost radio with some great features. Some new improvements include... Built-in 1000 mAh 1S battery, LiteRadio 2 SE increases the endurance to 8 hours. Updates with BETAFPV self-developed LiteRadio System. Pilots can directly operate the Joystick Calibration and Upgrade Firmware on the radio transmitter. Supports Frsky D8, Frsky D16 FCC and Frsky D16 LBT mode via the radio transmitter. Comes with 100mW transmitting power, LiteRadio 2 SE brings a wider operating range. Check out our RC Transmitters, our FrSky Products, and all our BetaFPV products! This radio does not support newer FrSky receiver firmware. Features LiteRadio 2 SE upgrades with BETAFPV self-developed Customized LiteRadio System. Pilots can directly operate the Joystick Calibration and Firmware Update on the radio transmitter, which is more convenient for the beginner racer to operate. Equipped with a built-in 1000 mAh 1S battery, LiteRadio 2 SE can use up to 8 hours, bringing an excellent endurance performance. Comes with a built-in charging module, LiteRadio 2 SE can support USB charging which is more convenient to use. Meanwhile, it designs a Low-Power warning to indicate a low battery. While it needs to be re-charged, the blue light will flash slowly. Compared with the LiteRadio 2, LiteRadio 2 SE has a larger transmitting power which can reach 100mW, bringing a wider operating range. Adopted the rubber coat, LiteRadio 2 SE is ergonomic and has the shape of a gaming controller. It's comfortable to hold, and the anti-slip texture on the handles allows for a solid grip. This radio transmitter acts as a USB Joystick when connected to a personal computer. So you could use it to play FPV simulators like EREADRONE. Specifications Frequency Range: 2.4GHz (2403MHz-2447MHz) 2.4G System: NRF24L01 or CC2500 Channel: 8 Support Protocol: Bayang / Futaba S-FHSS / Frsky D16 FCC/ Frsky D16 LBT/ Frsky D8 Power: ≤100mw Adapted Drone Type: Multirotor Support USB Charging / Firmware Update Support BETAFPV Simulator Connected / Customized LiteRadio System / Joystick Calibration LED Light: Green-Power On / Red-Warning / Blue-Normal Battery: Built-in 1000mAh 1S Battery Charging Connector: Type-C Includes 1x BetaFPV LiteRadio 2 SE RC Transmitter 2.4GHz - FRSKY D8/D16
$44.99
RaceDayQuads BetaFPV LiteRadio Transmitter Strap - Choose Version
Beta FPV LiteRadio transmitter neck strap adopts comfortable soft nylon or polyester material. The buckle is made of high-quality metal, durable, and handy detachable. Besides, the strap is adjustable, which will match you perfectly. This neck strap not only can be used for LiteRadio 3 but also other transmitters with the hook. Check out the rest of our transmitters, parts & accessories, and our BetaFPV selection! Features Made of high-quality nylon or polyester material. It is comfortable and soft. The buckle is made of high-quality metal, durable, and handy detachable. With adjustable function, this strap will fit you perfectly. Two colors for the options. The white color is designed with BETAFPV/ELRS printing, and the black strap is reflective. This neck strap not only can be used for LiteRadio 3 Transmitter but also other transmitters with the hook. Includes BetaFPV LiteRadio Transmitter Strap
$5.99
RaceDayQuads BetaFPV LiteRadio 3 Pro RC Transmitter - Choose Version
The LiteRadio 3 Pro Radio Transmitter is an open-source radio remote control that supports the EdgeTX system. It comes with the hall gimbals, featuring four precision bearings, adjustable spring tension, and ergonomic stick ends for an unparalleled feel. The OLED display screen on the top of the transmitter brings visually instant data and a controlling interface to users. What's more, an alternative external nano TX module make it a multi-protocol transmitter. Check out our RC Transmitters and all our BetaFPV products! Features Hall gimbals features four precision bearings, adjustable spring tension, and ergonomic stick ends for an unparalleled feel. Built-in 2000mAh 1S battery, LiteRadio 3 Pro can work up to 15 hours without an external module, bringing an excellent endurance performance. A 1.3-inch OLED display screen is newly installed. Controlled by two 5D buttons and settings are easy to be adjusted directly from the display screen. There is also a nano bay for an external TX module, it supports many popular modules in the market and meets all the protocols such as MULTI, CRSF, PPM, XJT, DSM2, R9M, etc. Specifications Channels: 8 Gimbals: Hall Sensor Frequency Range: 2.4GHz Antenna: Internal Antenna RF Output Power: 50mW, 100mW, 250mW (ELRS 2.4G) / 100mW CC2500 Screen: 1.3 inch OLED display screen Protocol: ExpressLRS 2.4G or CC2500 Battery: Built-in 2000mAh 1S Battery Operating system: EdgeTX Port: Type-C USB 3.0 port / 3.5mm Audio port USB Support: Most Practice Simulator / USB charging / Firmware update / Passthrough (ELRS 2.4G) Includes 1x BetaFPV LiteRadio 3 Pro RC Transmitter 1x User Manual 2x Joystick Protective Covers
$89.99
RaceDayQuads BetaFPV Lite Radio 3 2.4GHz RC Transmitter - Choose Version
All products with batteries must be shipped by a ground shipping method. The Beta FPV LiteRadio 3 Radio Transmitter is the newest remote control in the LiteRadio series. This transmitter features an ergonomically designed handle and has superb performance in its working time and newly updated gimbals. Besides, this version supports BETAFPV Configurator which is a utility designed to simply update, configure, and tune the radio controller. Check out our RC Transmitters and all our BetaFPV products! Features 8 channels in total USB Joystick support for most practice simulators Nano module bay for external TX module Newly designed joystick gimbal for longer usage life Support BETAFPV Configurator for updating, configuring, and tuning Built-in 2000mAh battery and USB charge supported Specifications Frequency Range: 2.4GHz Channels: 8 Support Protocol: Futaba S-FHSS/Frsky FCC D16/Frsky LBT D16/Frsky D8 or ExpressLRS 2.4G Power: ELRS version 25mW/50mW/100mW, Frsky version 100mW Support USB Charging / Firmware Update: Yes LED Light: Green-Power On / Red-Warning if the voltage is lower than 3.5V / Blue-Normal Battery: 1S 2000mAh Charging Connector: USB 3.0 Type-C Includes 1x BetaFPV Lite Radio 3 2.4GHz RC Transmitter
$59.99
RaceDayQuads BetaFPV LiPo Safety Hand Bag
The safety handbag is stitched together with an extremely strong fire retardant thread and has a double-zipper lid. It offers extra protection for your lipo battery, micro drone, and your charging location, which could protect your home and valuables from a fire due to a lipo battery failure. Useful for storage, travel, and charging. Check out all our battery chargers & accessories, and our BetaFPV gear! Features Waterproof, fireproof, and radiation protection Large space to place multiple batteries Middle spacer, battery can be classified Double zipper, makes the lipo safe bag well-sealed and convenient to use This flame retardant bag is a convenient way of safeguarding your Lipo batteries during charging, transit, and storage Specifications Color: Black Dimension: 165*90*120mm Weight: 130g Application: For safer charging and storage of Lipo batteries and drone Material: Textile Fiberglass Material with Fire retardant coating Includes 1x LiPo Battery Drone Safety Handbag
$6.99
RaceDayQuads BetaFPV HQ 3030 Tri-Blade 3" Prop 4 Pack (1.5mm) w/ Mounting Screws
Spare replacement props for the BetaFPV HX115 and HX115 HD. Check out the rest of our HX115 parts & accessories and our BetaFPV selection! Specifications Material: Poly Carbonates Length: 3 inches, about 76.2mm Color: Randomly 4 colors, Black, Blue, Transparent Red, Transparent Purple, Transparent Green Mounting hole: 1.5mm Weight: 1.5g(1 pcs), 6g (4 pcs) More Power, Control, and Speed for 2-3 inch sized FPV Micro Racing Drones Includes 4x BetaFPV HQ 3030 Tri-Blade 3" Prop 4 Pack 1x Mounting Screw Set
$2.49
RaceDayQuads BetaFPV Gemfan 1815 Bi-Blade 45mm Micro/Whoop Prop 4 Pack (1.5mm Shaft) - Choose Your Color
Take your drone racing to the next level with BetaFPV's Gemfan Ducted 1815 Bi-Blade 45mm Micro/Whoop Prop 4 Pack. With a 1.5mm shaft and 2-blade design, you'll enjoy increased power and quicker speed. Make sure you're always ready to fly with this reliable and efficient prop. The 2-Blade props feature high efficiency and are precise in operation for freestyle. Check out all our Micro Props and BetaFPV gear, as well as all of our Gemfan products! Specifications Material: PC Weight: 1.30g/set (2-Blade) Blades: 2-Blade Pitch: 1.5 inch Propeller Diameter: 45mm Shaft: 1.5mm Includes 1x BetaFPV Gemfan 1815 Bi-Blade 45mm Micro/Whoop Prop 4 Pack (1.5mm Shaft) - Choose Your Color
$2.49
RaceDayQuads BetaFPV GoPro Lite Case V2 for Naked GoPro Hero 6-7 Black - Optional BEC Board
Disassemble at your own risk, we are not responsible for any damage to your camera! Plastic injection molded GoPro Lite case from BetaFPV. BEC board is optional and also has an adapter for the BetaFPV ND16 Filter for GoPro Lite This case and BEC board fit the GoPro HERO6 and GoPro HERO7 Black. But NOT for GoPro HERO8. Check out all our replacement cam parts & accessories and all our BetaFPV selection! Features Plastic injection molded, Easy assembly Lightweight Specifications Weight: 6.57g Output: 5V@2A Voltage: 2-4S Includes 1x BetaFPV GoPro Lite Case V2 for Naked GoPro 1x BEC Board Instructions for Assembly How to Assemble Step 1: Assemble the BEC board on the GoPro motherboard. Step 2: Hold the camera lens and the camera board at the same time, be careful when you assemble the board on the case. Step 3, 4: Screw the GoPro motherboard with the M1.4*5 and M1.4*8screws as shown below Step 5: Install the light pipe as shown below. Step 6: Install the back case, and screw the board with M1.4*8 screws as shown below. How to Disassemble GoPro HERO6 Black Special thanks to JONAH BLAESER who provided the method of disassembling GoPro HERO6 Black. If you are interested, please check the link to know the specific steps to make your own naked GoPro. GoPro HERO6 Black Disassembly Guide We also provided the method of disassembling GoPro HERO8 Black. If you are interested, please check the link. GoPro HERO8 Black Disassembly Guide Note: Do this at your own risk. You will lose your GoPro’s warranty and you may end up bricking the camera if something goes wrong. This guide is not authorized by GoPro and your camera is not guaranteed to work afterward.
$13.98
RaceDayQuads BetaFPV Gemfan 1815 Tri-Blade 45mm Micro/Whoop Prop 4 Pack (1.5mm Shaft) - Choose Your Color
Take your drone racing to the next level with BetaFPV's Gemfan 1815 Tri-Blade 45mm Micro/Whoop Prop 4 Pack. With a 1.5mm shaft and 3-blade design, you'll enjoy increased power and quicker speed. Make sure you're always ready to fly with this reliable and efficient prop. The 3-Blade props give more power and faster speed for racing. Check out all our Micro Props and BetaFPV gear, as well as all of our Gemfan products! Specifications Material: PC Weight: 1.69g/set (3-Blade) Blades: 2-Blade/3-Blade Pitch: 1.5 inch Propeller Diameter: 45mm Shaft: 1.5mm Includes 1x BetaFPV Gemfan Ducted 1815 Tri-Blade 45mm Micro/Whoop Prop 4 Pack (1.5mm Shaft) - Choose Your Color
$2.49
You have seen 48 out of 92 products