EMAX

Plug in your VTx at any time with 0 power start-up! Check out all our LEDs, and all our TinysLEDs products! Features Plug in your VTx at any time with 0 power start-up (Not Available with FlightOne at current time) Turn off your VTx on the line to avoid heat buildup Fast Team Race Pit stops (Sub second transitions possible) Compatible with all major VTxs Turn off VTx during races to test hover builds without interfering with other pilots in the air. Turn off VTx after Crash for clean video for other racers.  Solo Endurance Races, 3 quads ready on the line. Practice for more than 1 pack without taking off goggles. (Instructions on how to setup on OpenTX / Spektrum Coming soon) LED Indicator light on board. (Light On \ Power On) Can be used on any pad on Flight Controller.  Does not need a full UART.   I.E.: SmartAudio/Tramp on TX and RX for RealPit PinIO  Up to 4 RealPits per quad. This opens the possibility for LEDs, and VTX, and any other device you can imagine.  Toggle LED Power or any other devices under 1 amp draw. Specifications Currently Supported Software: Betaflight (PinIO 3.3.x or Greater)  Butterflight (PinIO) FlightOne 1.2.4 + (PINTOGGLE) Operating Voltage: 5V - 28V (HV-6s) 1Amp Switch Dimensions: 10 x 12.5 x 2.5 mm Weight:  0.5 Grams w/ Heatshrink Includes 1x TinysLEDs RealPit VTX Power Switch 1x 1/2" Heat shrink piece Demo Video ( Team EMAX Team Race):  Setup Betaflight Settings:    In CLI: Type RESOURCE Locate UART TX/RX pad resource ID you are using.  We wired to RX4 in this demo. RX4 is A01  Note the name of resource and ID.  Next we will clear that pad from its assigned resource. Type  RESOURCE SERIAL_RX 4 NONE   Next we will set the Custom Mode Switches. We will set up 1 switch Copy and past these Commands into CLI:   set pinio_box = 40,41,42,43 aux 2 40 2 1600 2100 0   Next we need to assign the Resource ID to the Custom Mode switch. Using the Resource ID from above. "A01" resource PINIO 1 A01   If you wish to set up more pads for additional RealPits. replace the area in brackets with your resource IDs: Copy these extra lines to add more modes as well.:   set pinio_box = 40,41,42,43 aux 3 41 3 1600 2100 0 aux 4 42 4 1600 2100 0 aux 5 43 5 1600 2100 0 resource PINIO 2 [resource=I.E=A04]resource PINIO 3 [resource=I.E=A05]resource PINIO 4 [resource=I.E=A06] Type  SAVE  in CLI and then press enter. Your FC will reboot after applying changes.  Now go to Modes and Assign an AUX channel to the USER1 mode. Just like an arm or turtle mode switch. Click SAVE.  Now flip the switch and test. A RED LED will be lit on RealPit if your are providing power.   FlightOne Settings:  At the current time you must use Firmware version 1.2.x or greater to enable "PINTOGGLE" commands. This is available on FlightOne Discord. flightone.com/discord and website at FlightOne.us  Wire RealPit VTX + to VTX Positive pad and BATT+ to Battery Source (5v-28v) Wire VTC pad to TX4 pad on FlightOne FC. Solder the TX4 to NOR.  Then Wire GND pad to GND pad on FlightOne FC In Setup Tab: Setup PINTOGGLE switch.  Use Switch to Power VTX on and off.  Notes: FlightOne Does not support ZERO power on. VTX will blip for a micro second prior to turning back off.     Wiring Diagram Instructions:      Tags: real pit, vtx power switch, unify switch, pit mode switch, vtx pit mode, vtx paralyze, 

Read more less

All batteries must be shipped by a ground shipping method. The RDQ Series of LiPos now includes the perfect solution for your EMAX Tiny Hawk! Also available in a 5 pack.  Specifications Capacity: 450mAh Dimensions: 62x17x6.9mm Includes 1x 3.8V 1S 450mAh 80C LiHV Battery  

Read more less

For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 AIR Unit shooting, which can achieve an excellent anti-shake effect. The O3 Air Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: Link Camera: RunCam Wasp Antenna: GEPRC Peano 5.8G LHCP U.FL Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: PNP (built-in DJI receiver), ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 HD Wasp 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut

Read more less

For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: GEPRC 5.8GHz@600mW Camera: Caddx Ratel2 Antenna: GEPRC Peano 5.8G RHCP MMCX Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 Analog 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut

Read more less

Spare replacement part for the EMAX Tinyhawk II. Check out all our TinyHawk parts, and EMAX gear! Includes 1x EMAX Tinyhawk II Polypropylene Frame Kit

Read more less

Spare replacement part for the EMAX Tinyhawk II. Check out all our TinyHawk parts, and EMAX gear! Includes 1x EMAX Tinyhawk II Hardware Kit

Read more less

All batteries must be shipped by a ground shipping method. The Tinyhawk 1s lipo battery is a big part of the whole design around the great flight performance of the Tiny Hawk. The weight, the size, and the power from the High Voltage 450mah capacity cell were all considered during the design process. Engineers tested countless hours of flight and performance to achieve the best Lipo battery for you to enjoy up to 4 minutes of flying time! Our pilots agree that at least 4-6 batteries will be required to have the best flying experience for an all day fun fly! Required charger type: Any charger that has 4.35 High Voltage capabilities. This will keep you flying for up to 4 minutes per charge. Be sure to check out our all micro packs, and all our EMAX gear!  Specifications Voltage: 1S 4.35V HV Capacity: 450 mAh Discharge rating: 80c/160c Connector: PH2.0 Includes 1x EMAX TinyHawk 3.8V 1S 450mAh LiHV Whoop/Micro Battery - PH2.0    

Read more less

Replacement Tinyhawk 3 hardware kit that includes a complete hardware set for your model including spares and rubber bands. Check out the rest of the Tinyhawk line and all our EMAX gear! Includes EMAX Tinyhawk III - Hardware Kit

Read more less

Replacement Tinyhawk 3 frame that includes all plastic pieces necessary to freshen up your model. Check out the rest of the Tinyhawk line and all our EMAX gear! Includes EMAX Tinyhawk III - Frame

Read more less