Experience the efficient and reliable AIO solution of the AxisFlying Argus F722 F7 for your Whoop/Toothpick builds, complete with 40A 8Bit 4in1 ESC and pink aluminum shell. CNC heat sink on both sides ensures better cooling and longer service life.  Browse the rest of our Whoop AIO Boards and all our Axis Flying Products! Feature Every AIO goes through 800 full-throttle takeoff and landing tests before leaving the factory. High-quality circuit technology and aluminum shell casing will ensure their service life.  Stylish CNC heat sink on both sides. Better cooling and increased lifespan. The big concern of every pilot - desyncs - will be solved by the Argus F7 AIO.  Perfectly match with 20/21 motors. PNP HD VTX interface Specifications FC target: AXIS ARGUS F7 AIO DJI O3 dedicated plug: Supported Barometer: Supported  Beeper: Supported Sized: 36x36x7.2mm MCU: STM32F722RET6 Gyro: BMI270 Continuous Current: 40A Peak Current: 50A Uart: 5 OSD: Supported LED: Supported Input Voltage: 4-6S Mounting: 25.5x25.5mm/26.5x26.5mm M3  Includes 1x Axisflying Argus F722 F7 Whoop/Toothpick AIO Flight Controller w/ 40A 8Bit 4in1 ESC & Pink Aluminum Shell

Read more less

 All products with batteries must be shipped by a ground shipping method. Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right power performance.  BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate  a bigger battery.  Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP.  Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection! Features The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks. It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter. Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better. Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board. The various colors of the spare parts including the Meteor75 Pro frame and Micro Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it. Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals. HD Digital VTX System The Walksnail Avatar HD Mini 1S Lite uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 7.8g lightweight, compatible with 1S whoop drone. Built-in 8 GB storage, this VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode, Betaflight full OSD display is supported and can be adjusted easily by remote control. Note: Please make sure that the battery voltage must be 3.1V at least when flying, otherwise, the HD digital VTX would stop working. Flight Controller The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC. Meteor75 Pro HD (ELRS) Meteor75 Pro HD (Frsky, PNP, TBS) FC Inside F4 1S 5A FC (Serial ELRS 2.4G) V2.0 F4 1S 5A FC (SPI Frsky) V3.0 Gyro BMI270 BMI270 FC Firmware BETAFPVF411 BETAFPVF411RX UART Port One UART Port Two UART Ports External RX Not Supported Supported Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD. Micro Canopy Lite Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone. Endurance Boosting Battery With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots. Meteor HD Series BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images. Meteor75 Pro Frame Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately. Powerful 1S Drone Combo Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots. Specification Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX) Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero) Camera Adjustable Angle: 0-40° Motors: 1102 22000KV Motor Battery: BT2.0 550mAh 1S Battery Frame: Meteor75 Pro Brushless Whoop Frame Propellers: Gemfan 45mm 3-Blade Propellers Canopy: BETAFPV Micro Canopy Lite Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero) Receiver: Serial ELRS 2.4G/SPI Frsky/TBS FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0 VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero) VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera FAQ Download the FC firmware and CLI dump file for Walksnail and HDZero version. Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit. Click to download the manual for HDZero Whoop Lite Bundle. Includes 1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver 2x BT2.0 550mAh 1S Battery 1x Type-C USB Cable 1x BT2.0 Battery Charger and Voltage Tester 4x 45mm 3-Blade Props (1.5mm Shaft) 1x Screwdriver 1x VTX USB Cable (Walksnail or HDZero Version) 1x Pack of Screws

Read more less

Pre-Orders shipping ASAP! For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer. DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ. BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.  The 4S version comes with powerful 1504-3600Kv motors, and choose between PNP (No RX)  or ELRS 2.4GHz for your receiver! Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!  Features Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high-cost performance； It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster; The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable; The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash; The independent action camera base can be used with naked GoPro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.   Specifications Brand: DarwinFPV Model: BabyApe Ⅱ 4S Frame: Wide X Wheelbase: 156mm Size: 126mmx150mmx50mm Flight Control: F411 MPU6500 AT7456E Firmware：DARWINF411 Firmware: BETAFPV_Nano_2400_RX The receiver's factory firmware is ELRS_V3.2.0 Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB ESC: Bluejay 48KHz 3-6S 30A Motor:  4S version：1504-3600KV Propeller: HQProp T3.5x2x3GR-PC Weight: 135.4 g (analog version) Receiver: ELRS 2.4GHz Darwin FPV "Cement" Ultra Durable FPV Drone Camera Sensor type：1/3" CMOS Sensor Image：16:9 TV System: NTSC Horizontal Resolution：1200TVL Lens：2.1mm 160° Electronic Shutter: 1/50~1/100000 sec Video Output: CVBS Min. Illumination：0.001Lux wb: automatic DNR: 3D DNR WDR: 100db Input voltage: DC 3.7-24V Working current：80mA@DC12V/170mA@DC5V IP: IP67 Size：19x19mm Weight：7.9g DarwinFPV 25/200/400/600mW VTX Output Power: 25/200/400/600mW(adjustable) Frequency: 5.8Hz 40port Power Supply Voltage Range: 5V Weight: 3.5g Pitch: 28x15mm(length x width) Protocol: SmartAudio Indicator Light Description: Includes 1x DarwinFPV BNF Baby Ape V2 3.5" Analog Micro Quad - 4S - Choose Your Receiver 4x HQProp T3.5x2x3GR-PC 2x Battery cable strip ( 10x170mm) 2x EVA shock pad（thickness：10㎜） 1x Spare screws bag 1x Sticker 1x Manual

Read more less

Pre-Orders shipping ASAP! For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer. DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ. BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.  The 6S version comes with powerful 1504-2300Kv motors, and choose between PNP (No RX)  or ELRS 2.4GHz for your receiver! Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!  Features Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high cost performance； It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster; The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable; The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash; The independent action camera base can be used with naked gopro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.   Specifications Brand: DarwinFPV Model: BabyApe Ⅱ 6S Frame: Wide X Wheelbase: 156mm Size: 126mmx150mmx50mm Flight Control: F411 MPU6500 AT7456E Firmware： DARWINF411 Firmware: BETAFPV_Nano_2400_RX The receiver's factory firmware is ELRS_V3.2.0 Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB ESC: Bluejay 48KHz 3-6S 30A Motor： 6S version：1504-2300KV Propeller: HQProp T3.5x2x3GR-PC Weight: 135.4 g(analog version) Receiver: ELRS 2.4GHz Darwin FPV "Cement" Ultra Durable FPV Drone Camera Sensor type：1/3" CMOS Sensor Image：16:9 TV System: NTSC Horizontal Resolution：1200TVL Lens：2.1mm 160° Electronic Shutter: 1/50~1/100000 sec Video Output: CVBS Min. Illumination：0.001Lux wb: automatic DNR: 3D DNR WDR: 100db Input voltage: DC 3.7-24V Working current：80mA@DC12V/170mA@DC5V IP: IP67 Size：19x19mm Weight：7.9g DarwinFPV 25/200/400/600mW VTX Output Power: 25/200/400/600mW(adjustable) Frequency: 5.8Hz 40port Power Supply Voltage Range: 5V Weight: 3.5g Pitch: 28x15mm(length x width) Protocol: SmartAudio Indicator Light Description: Includes 1x DarwinFPV BNF Baby Ape V2 3.5" Analog Quad - 6S - Choose Your Receiver 4x HQProp T3.5x2x3GR-PC 2x Battery cable strip ( 10x170mm) 2x EVA shock pad（thickness：10㎜） 1x Spare screws bag 1x Sticker 1x Manual

Read more less

The props for this BNF press fit on and do not screw into the motor (much like many other Whoops & Toothpicks) The Darwin Baby Ape has been loved by many pilots as soon as it was published. In order to design a better FPV drone, DarwinFPV upgraded the Baby Ape based on the pilots' feedback and launched the BabyApe Pro V2. Darwin made several upgrades to the frame. First of all, nylon standoffs are upgraded to aluminum alloy standoffs, which strengthens the frame and stables structure. Second, they added the receiver fixing bracket. Third, they upgraded the arms. The arms are upgraded from 4 individual arms (2.5mm thickness) to 2 integrated arms (3.0mm thickness). It is easier to disassemble, sturdy, and durable. Lastly, the V2 version only needs 4 screws to fix, and the arm can be replaced by removing 2 screws without removing the whole drone. Make sure to check out all of our BNF quads as well as the rest of our DarwinFPV selection! Specifications Motors Input Voltage: 2-3S Stator Size: 11x4mm Kv: 4300 AIO MCU: STM32F411 Gyro: MPU6000 BEC: 5V/2A,3.3V Input voltage: 1-3S Lipo Support Receiver: PPM, Ibus, Sbus, Dsmx Black box: NO Barometer: NO Firmware: MATEKF411 Buzzer interface: YES Betaflight OSD: AT7456E Constant current: 15A Peak current: 17A MCU: EFM8BB21F16G(48MHz) Firmware: BLHeli_S Protocol: Dshot600 Mounting: 25.5X25.5 M2 VTX Input Voltage: 7V~24V RF Output Power: 0mW/25mW/100mW/200mW switchable Antenna Connector: U.FL Caddx Ant Camera Model: Caddx Ant Image Sensor: 1/3" CMOS Resolution: 1200TVL Signal System: PAL/NTSC Includes 1x DarwinFPV BNF Baby Ape Pro V2 3" Quad - Plug-N-Play - Choose Version

Read more less

CineApe25 is DarwinFPV’s first cinematic whoop FPV drone. The frame is composed of upper and lower carbon plates and a high-strength injection guard, which is very strong and crash-resistant, and easy to disassemble. The motor adopts a 1504-3600KV long-life motor; we abandoned the traditional AIO solution and adopted the split design of the F4, 30A stack to reduce the maintenance cost in the future. The accessories adopt mature and stable solutions to maximize the durability and reliability of the drone. Be sure to check out our Cinewhoop Collection as well as all DarwinFPV products we have for sale at RaceDayQuads! CineApe25 is a very cost-effective whoop FPV drone. It not only solves the worries of beginners about the high-risk factors and high threshold of assembly but also improves the after-sales experience. If you are still struggling with which FPV drone to buy, DarwinFPV CineApe25 may be your best choice! Features Comes with high-strength one-piece injection-molded propeller guard, which has higher safety, and a stronger and more durable frame, also reduces the probability of risk, so you have more confidence to fly. The new ducted aerodynamic design greatly optimizes power efficiency, and with the 1504-3600KV long-endurance motor, the CineApe 25 has a battery life of up to 9mins. Compared with traditional stacks, we have treated the CineApe 25 stack with glue to protect it, which greatly reduces the risk of damage to the stack due to contact with metal particles, fine sand and gravel, weeds or dewdrops, etc. The external Type-C parameter adjustment port is convenient for parameter adjustment. It comes with quick-release design only needs to remove 7 screws to separate the top plate and the injection molding guard, which can easily deal with the scene in which accessories need to be replaced urgently. The stack has built-in barometer and SD card slot, and reserves rich interfaces resource, which is facilitate upgrade and DIY in the future. There are optional versions and HD VTX solutions can be provided. Specifications Brand: DarwinFPV Model: CineApe 25 Cinematic FPV Drone Frame Structure: True-X Wheelbase: 112mm Dimension: 160x160x43mm Motor: 1504-3600KV Propeller: HQProp T63MMX6 Recommend Battery: LiPo 4S 850mAh Hovering Time: 9mins (4S 850mAh Battery) Weight: 144g (Without Battery) Flight Controller: F411 MPU6500 AT7456E Reserved Connector: 1x SBUS (RX1 inverter), 2x Uarts 2x Softserial, 1x I2C, 1x RGB, 1x Buzzer, 1x USER (A15), 1x USB ESC: BlueJay 3-4S 30A Analog Version: CADDX ANT Analog CAM + 600mW Analog VTX Includes 1x CineApe 25 Cinematic FPV Drone 4x HQProp T63MMX6 propeller (2L2R) 2x battery strap 10x170mm 1x EVA crashproof foam 1x EVA bottom plate shock-absorbing pad 1x Spare Screw Kit 1x Sticker 1x Manual  

Read more less

Overview NOW EVEN EASIER TO FLY The UMX™ Radian® ultra-micro motor glider became a class favorite by delivering a unique flying experience you simply can't get from any other model. Due to its traditional motor glider design, the Radian is inherently stable and easy to fly almost anywhere — indoors in gymnasiums and other suitable spaces, and outdoors in most yards, parks and sports fields. The exclusive Spektrum™ AS3X® technology of its installed electronics smooths out the effects of wind and turbulence to deliver a locked-in feel that makes it seem like you're flying a much larger airplane. E-flite® engineers upgraded this new version to include optional-use SAFE® Select technology, making the Radian even easier for more people to fly in more places. Plus, you can receive real-time battery voltage telemetry with compatible transmitters! It's the perfect next step after learning to fly, a great first glider and an exciting everyday sport model for a wide variety of pilots. Features Updated and upgraded version of the very popular ultra-micro motor glider that's easier to fly in more places than ever before Fly indoors in gymnasiums and other suitable spaces, or outdoors in most yards, parks, sports fields and beyond Long flight times up to 10-20+ minutes with a mix of power on/off flying using 1S 150–200mAh batteries Removable one-piece wing with composite spar for easy and convenient storage and transport Provides telemetry data to compatible transmitters to show flight battery voltage Easier to fly with innovative and optional-use SAFE® Select flight envelope protection The unmatched stability and locked-in feel of exclusive AS3X® technology Spektrum™ receiver with industry-leading 2.4GHz DSMX® technology Factory-installed motor, gearbox and efficient folding propeller No FAA registration required (under the 250-gram weight limit) Factory-finished and ready to fly right out of the box UPDATED FOR ULTRA-SMOOTH SOARING The ever-popular UMX™ Radian® has been updated and upgraded so it's even easier and more fun to fly than before! The ultra-micro motor glider now includes exclusive Spektrum™ optional-use SAFE® Select technology and provides real-time battery voltage telemetry to compatible transmitters. This Bind-N-Fly® Basic model arrives factory-assembled and nearly flight-ready right out of the box. Simply install the one-piece wing with a few screws, install a charged battery, bind it to your compatible Spektrum transmitter and fly. Advanced EPS construction provides a lightweight yet durable airframe. The distinctive, gracefully curved polyhedral wing and efficient airfoil deliver outstanding soaring performance and long flight times with or without motor power. The factory-installed power system features a coreless motor, gearbox and an efficient folding propeller. It produces excellent climb performance and extends flight times up to 10-20+ minutes with a mix of power on/off flying using 1S 150-200mAh batteries. Because of its ultra-micro size, the UMX Radian can be flown indoors in gymnasiums and other suitable spaces, or outdoors pretty much anywhere — in most yards, parks, sports fields and beyond! If you learned to fly with a HobbyZone® Sport Cub S, you can use the same transmitter, battery and charger and make the Radian an economical next step. It's an ideal first glider or everyday sport model for low-time to experienced pilots interested in an easy to fly, ultra-micro class motor glider that delivers a unique flying experience!

Read more less

In an effort to push the boundaries of carrying the camera on the smallest platform, Flywoo designed the smallest quadcopter possible in their history. The Firefly Baby Quad is a nano-sized FPV drone designed to carry an Insta360 Go, or SMO 4K cameras for some action flying.  Weighing in at just 47g, the Firefly Baby Quad is small, flexible, and stable. It's full of power and offers unmatched control. Pilots can quietly enjoy the fun of shooting a video without jello. Perfect for the indoor and outdoor recording of every beautiful flying moment! Check out our other pre-built quads, as well as other great products from Flywoo! Specifications Weight: 47g Wheelbase: 80mm FC & ESC : GOKU GN405 Nano 13A STACK ( 16x16 ) Frame: Firefly Baby Quad Frame (Analog Verison) Motors: Nin V2 1203Pro 5500KV Props: Gemfan 1636 40mm-4 V2.0 VTX: Goku VTX625 450mw Antenna: Atomic 5.8GHz Antenna Length 30mm (RHCP) Battery: 4S 450mAh / 4S 300mAh battery (Not including) Flywoo GOKU GN405 NanoFlight Controller MCU: STM32F405 BGA IMU: ICM42688 UARTS: 6 Soft Serial Ports: 2 I2C: Yes Onboard LED：WS2812x8(FCx4/ESCx4) Supports: SBUS, iBus, Spektrum, Crossfire BlackBox: 16Mb Flash BEC: 5V Power Out: 2.0A max, 3.3V Power Out: 0.5A max Dimensions: 22x22mm Mounting Holes: 16x16mm Weight: 2.3g Flywoo GOKU BS13A 4in1 ESC Support: Oneshot, Multishot, Dshot150, Dshot300, Dshot600 Input Voltage: 2-4S Lipo Continuous Current: 13A Firmware: BLHELI_S Mounting Pattern: 16x16mm, M3 Hole Weight: 2.5g Nin V2 Motor Stator Size: 1203 KV: 5500 Goku VTX625 450mw Raceband: 5362-5945 MHZ Power: PIT/25/50/100/200/450mW switchable Input Voltage: 5V Control Mode: IRC Tramp(RX) & Button Video System: NTSC/PAL Antenna: IPEX (U.FL) Size: 30mmx30mmx4mm Weight: 1.3g Includes 1x Flywoo BNF Firefly Baby V1.3 4S 1.6" Analog Micro Quad - Choose Receiver

Read more less

Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card. The CineRace is a double duct design, not a simple guard anymore. It can fly as flexibly as a racing drone, and as stable as Cinewhoop. All in all, this is a  drone that can not only race but also capture stable videos and at the same time achieve a super long flight time! A specially designed GM10 Nano V3 GPS module is tailored to fit the CineRace20, providing minimal weight but the ability to search up to 30 satellites. You will see on the front of the quad Flywoo engineer the use of the soft TPU material to mount the camera to prevent the jello effect, by reducing the over all vibrations in the quad. Come see our  Cinewhoop Collection and other great products from Flywoo! We also carry a version with the O3 Air Unit already installed here. Features Almost all parts are injection molded for a more sturdy and durable quad. Very easy to disassemble, only fixed by two aluminum columns Customizable with LEDs GPS up to 30 satellites Innovative duct design Sub250 (even with battery) Specifications Input Voltage: 4S Model: CineRace20 HD DJI O3 2inch (without Air Unit) Brand: FLYWOO Frame: CineRace20 O3 (Different fromCineRace20 V1.2\V2 frame ) Charge connector: XT30 Motor: NIN V2 1203PRO 4850Kv Propeller: D51-5 51mm  Buzzer : 5PCS Active Alarm Buzzer GPS: GOKU GM10 Nano V3 GPS Weight: 139g (without battery) Betaflight Firmware target: FLWO/FLYWOOF405S_AIO(SMT32F405) Recommended Battery:Explorer 450mah 4S ( flight time  5mins ) Explorer 750mah 4S ( flight time  6mins )  GOKU GN F405S 20A AIO Input Voltage: 2-6S Lipo MCU: STM32F405 BGA IMU: ICM42688 OSD: BetaFlight OSD  Blackbox: 16Mb Flash Baro: BMP280 BEC: 5V 6 hardware UARTS (UART1,2,3,4,5,6) Onboard LED：4x WS2812 Support BLHELI_S Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600 FPV System Add your own O3 Air Unit Includes 1 x Flywoo CineRace20 HD V2 Neon LED 4S Cinewhoop (without O3 Unit) - PNP 8 x D51-5 props 2 x Battery strap  9x150mm \ 9x200mm 1 x Set of screws 1 x 90° USB Type-C 

Read more less

Taking your drone photography to the next level, the new series Cinebot30, take you to the real world, shooting extreme footage. Cinebot30 is a new generation of Cinematic FPV drone developed by GEPRC team. The high-strength 7075 aircraft-grade aluminum alloy bracket for FPV camera escort, the combination of classic engineering and aesthetics. The newly polished gimbal damping module can easily fix high-frequency vibration and jello issues. It can be mounted with GEPRC Naked GoPro Hero 8 and GoPro Black Bones, Insta 360 GO2 and other cameras. The image is stable and clear, and it’s easy to film. Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again! Cinebot30 will be equipped with a powerful 1804 motor with optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmx3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations. Finely polished frame design, only 6 screws need to be removed to separate the aircraft top plate and protection frame. Easy to cope with the urgent need to replace the accessories, at any time to restore the state. Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Design that combines engineering and aesthetics. Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts. Selected high-toughness and impact-resistant PC material for injection molding. Aviation 7075 aluminum alloy camera mounting bracket and fuselage aluminum column. Propeller guard embedded ring Cob light strip, carefully tuned light effect. Color brightness in the day and night can be clearly displayed. The newly developed gimbal shock absorption structure can disintegrate high frequency jitter and jello effect. Easily carry a variety of action cameras. Powerful 1804 motor, surging torque to deal with ultra-low altitude flight at will. With the new GEP-F722-45A AIO V2, stable performance, more secure flight Four kinds of FPV system with the program, choose to belong to your first-person view Tuned by GEPRC professionals, delicate and silky flying feel Specifications Input Voltage: 3-4S Wheelbase:127mm Isolation Plate:2mm Main plate:3mm Bottom plate:1.5mm Motors: SPEEDX2 1804-3450KV Propellor: HQ prop T76mmx3 propeller VTX: GEPRC RAD 1W Antenna: Peano 5.8G 110mm RHCP MMCX Antenna Camera: Caddx ratel 2 Weight: 206.4g GEPRC GEP-F722-45A AIO Model: Cinebot30 HD Nebula PRO Quadcopter Gyro: BMI270/42688 gyro/accelerometer(SPI) OSD: Yes ESC Connections: Yes Firmware: GEP-F722-45A AIO BEC: 5V 1A Current Sensor: Yes Buzzer: no Barometer: No Input Voltage: 2-4S LiPo MCU: STM32F722RET6 IMU: ICM-42688-P Stack Size: 25x25mm Dimensions: 32x32xmm Weight: 8.8g Includes 1x GEPRC BNF CineBot30 4S 3" Analog Cinewhoop - Choose Version 2  x  HQProp T76MM（pair） 1  x  Battery strap M15x200mm 1  x  Battery strap M15x220mm 2  x  Battery Silicone Pads 1  x  Set of screws 1  x  Set of screwdrivers 1  x  GoPro camera mount holder 1  x  Set of screws 1  x  Set of screwdrivers 1  x  Antenna fixed tube

Read more less

Since DJI released the O3 AIR Unit FPV high-definition video transmission system, the GEPRC team has followed closely to make the latest set of the O3 AIR Unit system, the Cinebot30 HD O3 AIR Unit version. The Cinebot 30 is a new generation of cinematic FPV drones developed by the GEPRC team. The aluminum parts of the camera are still made of high-strength 7075 aircraft-grade aluminum alloy materials. The TPU shock-absorbing pad is designed on the bracket structure, which can excellently isolate the high-frequency vibration of the fuselage so that the camera can still obtain jelly-free high-definition images during high-speed flight The installation of the video transmission has also designed an assembly scheme, which allows the O3 video transmission to be completely installed inside the fuselage without affecting the Type-C USB data cable connected to the Air Unit to read video data. O3 Air Unit is currently the most advanced FPV system on the market. It can transmit 1080P 60fps real-time images, and can also record up to 4K 60fps images with an anti-shake effect at the same time.The upgraded video transmission system also combines market feedback to upgrade the gimbal top plate of the fuselage, which is compatible with the camera base fixed by 4-hole screws, so that Cinebot30 can mount a full-sized GoPro camera very well, and the battery life can reach 5 minutes and 30 seconds. However, the GEPRC team recommends flying with Naked GoPro 10, with a battery life of up to 10 minutes and 30 seconds.Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!Cinebot30 will be equipped with a powerful 1804 motor with an optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmX3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations.Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots! Features Adopts the most advanced O3 Air Unit FPV digital video transmission system on the market Video transmission with high-definition anti-shake 4K 60fps ultra-high resolution video quality The highest bit rate is 50MBPS, the delay is as low as 30 milliseconds, and the highest image quality is 1080P 60FPS Upgraded the top plate of the fuselage gimbal, compatible with the camera base fixed by 4-hole screws, and supports mounting a full-sized GoPro camera for flight The camera aluminum mechanism is designed with TPU shock absorption, which can effectively eliminate the image jello caused by the vibration of the body The ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. Color brightness can be clearly displayed in day and night Selection of high-quality high-toughness, impact-resistant PC&PET material injection molding Powerful 1804 motor, surging torque to cope with ultra-low altitude flight Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts With the new GEP-F722-45A AIO V2, the performance is stable and the flight is more secure Tuned by GEPRC professionals, delicate and silky flying feel Specifications Model: Cinebot30 HD O3 Quadcopter Brand: GEPRC Frame:  GEP-CT30 O3 Wheelbase:127mm Isolation Plate:2mm Main plate:3mm Bottom plate:1.5mm FC: GEP-F722-45A AIO V2 MCU: STM32F722RET6 IMU: ICM-42688-P VTX:  DJI O3 Air Unit Video resolution: 4K@50/60fps, 2.7K@50/60/100/120fps, 1080p@50/60/100/120fps Camera:  DJI O3 Propeller: HQ prop T76mmx3 propeller Antenna: DJI O3 Antenna Charge connector: XT60H-M Motor: SPEEDX2 1804-2450KV（6S Version）/ SPEEDX2 1804-3450KV（4S Version） Weight: Nebula Pro version 222.5g / Avatar version 221g / Analog version 209.2g / Link Wasp version 222.5g / O3 version 234.7g (excluding battery, the above are TBS Nano RX version) Receiver: PNP, Frsky R-XSR, TBS Nano RX, ELRS 2.4G Recommended Battery: LiPo 4S 1100mAh-1300mAh (4S Version) / LiPo 6S 850mAh-1100mAh(6S Version) Includes 1x Cinebot30 HD O3 Quadcopter 2x HQProp T76MM（pair） 1x Battery strap M15x200mm 1x Battery strap M15x220mm 2x Battery Silicone Pads 1x Set of screws 1x Set of screwdrivers 1x GoPro camera mount holder 1x Set of screws 1x Set of screwdrivers 1x Antenna fixed tube

Read more less

Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season.  This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability. Check out the rest of pre-built quads and our HappyModel selection! Features X12 5-IN-1 AIO flight controller w/ built-in receiver and OpenVTX VTX Power up to 400mw RS0802 20000KV motors RunCam Nano 3. The lightest 1/3 CMOS 800TVL Camera Smooth and powerful Compatible with 1S Lipo/LIHV Specifications Input Voltage: 1S Max Continuous Current: 12A Motors: 0802 20000KV Camera: RunCam Nano 3 Wheelbase: 75mm Dimensions: 99x99x40mm Weight: 24g Includes 1x HappyModel BNF 1S Mobula 7 Whoop - PNP

Read more less

The HappyModel BNF 1S Mobula 7 HD Whoop version is a light and efficient 75mm brushless whoop which provides 1080P HD video recording functionality. HappyModel added blackbox for this 1s 75mm HD recording whoop so that you now have gyroflow functionality. Unlock the ultimate smooth flights with a combination of the Mob 7 HD and gyroflow! Check out the rest of pre-built quads and our HappyModel selection! Specifications HappyModel X12 AIO Input Voltage: 1-2S MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Gyro: MPU6000 or ICM20689 or BMI270 Max Continuous Current: 12A VTX Output Power: 25-400mW Antenna Connector: U.FL OSD: Yes Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX ESC Firmware: Z_H_30_REV16_7 Mounting Pattern: 25x25mm Weight: 5.1g HappyModel RS Motor Input Voltage: 1S KV: 20000KV  Shaft Diameter: 1.0mm Configuration: 9N12P Stator Diameter: 8mm Stator Length: 2mm Motor Dimension: Φ10.5x13.5mm Wire length(include connector): 30mm Weight: 2g Runcam Split 3 Lite Video Resolution: 1080@60fps/1080@50fps/1080@30fps/720@60fps Field of View(FOV): Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3) Video File Format: MOV Image Resolution: 2MP Signal System: NTSC (720*480)/PAL (720*576) Switchable Interface: JST 1.25mm / UART and SH 1.0mm Includes 1x HappyModel BNF 1S Mobula 7 HD Whoop

Read more less

HappyModel has been an amazing company, bringing us FPV enthusiast quality whoops to fly. Take a look at HappyModels first ever whoop on a 85mm frame. It comes with X12 series flight controller, EX1103 KV11000 motors and Gemfan Hurricane 2023 tri-blade propellers, all together gives this whoop an amazing performance for an extremely smooth flight.  Choose between PNP (No RX) and BNF (ELRS SPI 2.4) Be sure to check out all our pre-built quads, and all our Happymodel products! Features X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and OPENVTX VTX Power up to 400mw ELRS V2.0 (Default), can be flashed to ELRS V3.0 EX1103 KV110000 motors CaddxFPV Ant FPV camera Smooth and powerful Compatible for 1S-2S Lipo/LIHV battery 3D Printed Camera Lens Protector User Manuals ELRS (SPI) PNP (No RX) Specifications  Brand Name: Happymodel Motor: EX1103 KV11000 AIO: X12 5-IN-1 AIO flight controller Camera: CaddxFPV Ant FPV camera Prop: Genfan 2023-3 propellers  Weight: 42.7g Input Voltage: 1-2S Wheelbase: 85mm Size: 120mmx120mmx50mm Motor Specifications  Model: EX1103 KV11000 Configuration: 9N12P Stator Diamter: 11mm Stator Length: 3mm Shaft Diameter: Φ1.5mm Motor Dimension(Dia.xLen): Φ13.5mmx15.5mm Weight(g): 3.8g No.of Cells(Lipo): 1-2S Propeller Specifications Weight: 0.88g Material: PC Pitch: 2.3inch Props Dia: 52.17mm Center Thickness: 5mm Center Hole Dia: 1.5mm Flight Controller Specifications MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: ICM20689 or ICM42688P(SPI connection) Mount hole size: 25.5mm x 25.5mm Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 12A(each) Blheli_S 4in1 ESC Built-in Betaflight OSD(SPI Control) Built-in 5.8G OpenVTX 0mw~400mw Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A Built-in voltage detection Built-in current sensor Onboard 4in1 ESC Power supply: 1-2S LiPo/LiPo HV Current: 12A continuous peak 15A (3 seconds) Support BLHeliSuite programmable Firmware target: Z_H_30 Default protocol: DSHOT300 Support Bluejay firmware Onboard SPI ELRS 2.4GHz Specifications  Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V2.0 RF Frequency: 2.4GHz Antenna : SMD antenna Telemetry output Power: <12dBm Receiver protocol:  SPI ExpressLRS Could flash FC firmware to support ExpressLRS v3.0 TX module PNP Version Specifications  Full UART1 for external Receiver Support CRSF/GHOST/SBUS/IBUS/DSMX protocol IR1 pad(invert RX1) used for SBUS input Includes 1x HappyModel BNF Mobula8 1-2S Brushless Analog Whoop - Choose Your Receiver 1x Gemfan Hurricane 2023 tri-blade propellers (4CW+4CCW) 1x Screw Driver 1x Extra camera canopy

Read more less

The HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) AIO board featuring an F4 Flight Controller, onboard 12A 4-in-1 ESC, 5.8GHz OpenVTX and built-in receiver of your choice! Happymodel continues to impress with yet another fantastic AIO for whoop applications! Browse the rest of our Whoop AIO boards and all our Happymodel products!  Specifications Input Voltage: 1-2S MCU: STM32F411CEU6 (100MHZ, 512K FLASH) Gyro: MPU6000 or ICM20689 or BMI270 Max Continuous Current: 12A VTX Output Power: 25-400mW Antenna Connector: U.FL OSD: Yes Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX ESC Firmware: Z_H_30_REV16_7 Mounting Pattern: 25x25mm Weight: 5.1g ELRS Version Packet Rate: 50Hz/150Hz/250Hz/500Hz ELRS Firmware Version: V2.0 RF Frequency: 2.4GHz Antenna: SMD antenna Telemetry output Power: <12dBm Includes 1x HappyModel X12 2S AIO Whoop Flight Controller (F4 FC / 12A 4in1 ESC / 25-400mW VTX) 1x Connecting Wires Set 1x Hardware Set 1x Antenna

Read more less

Due to this item’s size or weight, it is not available for free shipping and may be shipped via ground. This is a PNP wing, but assembly is still required. Designed for FPV flying, the Heewing T1 Ranger PNP Twin Motor Wing is a great wing all around.  Lightweight and portable, with a quick disassembly design, this build only takes minutes to put together and take apart. A small wingspan with large space for stress-free placement  for your electronic equipment.  And many other features to check out! Check out all our PNP wings, Kit wings, and all out HeeWing products! Features Two-section hatch with ample room hatch for electronics High-Quality EPP / Carbon FIber / Aluminum Materials Supports External FPV Camera Mounting 730mm Fixed Wing Span Quick Release Structure Dual Motors Specifications Wingspan: 730mm  Length: 645mm Hight: 140mm Dimension: 660x225x135mm Propeller recommend: 5-6 inch Battery recommend : 4S 1300-2200mah Battery: 2S~3S 1300mah~5000mah LiPo Radio System: 2.4G 6CH Material: EPP / ABS+PC / Carbon fiber / Aluminum Includes 1x Heewing T1 Ranger PNP Twin-Motor Wing

Read more less

Introducing the BOB57, a 6" cinematic long-range quad pre-installed with the all-powerful DJI O3 system for crystal clear image quality. This quad aims to best of 5" and 7", hence the name BOB57. This quad is DJI PNP, meaning it does not come with a receiver, meaning you need to install your receiver.  However, if you have the DJI FPV Remote Controller 2, you can bind to the O3 Air Unit. This quad also comes with a GPS pre-installed, allowing all the marvelous features a GPS allows you. The BOB57 comes with XING2 2506 motors with a rated KV 1500, designed around 6S power.  The iFlight BOB57 is a long-range HD drone that was designed in collaboration with pilot & videographer Ellis van Jason. The team crafted this cinematic 6-inch drone that ensures agility and flight time while combining the advantages of both 5-inch and 7-inch drones for both cinematic and freestyle flights. Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products  Features Hybrid motor design optimized for  that can be used with both bi-blade and tri-blade 6" propellers. High-end GPS is used to minimize the risk of failure during proximity flights Long backbone with enough space up to fit 3000mAh 6S batteries Solid antenna mount for less oscillations when using long antennas Gladiator shell protects from dust and water droplets ESCs with built-in spike absorbers for more reliability Built-in BEC to directly power a GoPro camera 9-minute flight time with 3000mAh 6S Lipo Front-mounting XT-60 DJI O3 Air Unit VERSATILE BODY The Body is designed to carry small to large batteries for agile or long-range missions. SMART XT60 AND USB-C PLUG The XT60 plug is located in the front to gain more space. With the USB-C plug you can directly power your GoPro/Action Cams. OPTIMIZED MOTOR AND PROPS The Motor is designed for 6inch to give both great performance and efficiency. The prop is specifically optimized for this drone. RELIABILITY The BOB57 comes with a shell that protects against hits, droplets, and dust. It also has a high-quality GPS and components for more reliability, like a spike absorber & extra capacitor. PRE-TUNED AND PRE-SETUP Don't worry about tuning, iFlight did that for you already! A basic PID and Filter tuning were applied for a great flight experience! Links Ellis van Jason Tune Setup Specifications Product Name: BOB57 O3 6S HD BNF FC: BLITZ F722 ESC: BLITZ E55 55A 4-IN-1 ESC Video Transmission: DJI O3 Air Unit Frame: 280mm wheelbase Motor: XING2 2506 motors Prop: GEMFAN 6032-3 propellers Takeoff Weight: Approx. 580 g Dimensions (L×W×H)：226×166×34 mm Max Speed: 180 Km/h (Manual Mode) Maximum Takeoff Altitude: 7000 m Max Hover Time: Approx. 8 mins (With 6S 1400 no load.) Max Wind Speed Resistance: Level 7 Operating Temperature Range: -10° to 40° C (14° to 104° F) Antennas: 2 Antenna GNSS: GPS+SBAS+Galileo+QZSS+Glonass Video Transmission  Product Name: DJI O3 Air Unit Weight: Approx. 36.4 grams（headband included） Dimensions (L×W×H): L32.5x W30.5xH 14.5mm Communication Bandwidth： Max 40 MHz FOV (single screen): 155° Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz End-to-End Latency With DJI FPV Goggles V2: 810p/120fps Video Transmission Quality: The latency is lower than 28 ms. 810p/60fps Video Transmission Quality: The latency is lower than 40 ms. With DJI Goggles 2: 1080p/100fps Video Transmission Quality: The latency is as low as 30 ms. 1080p/60fps Video Transmission Quality: The latency is as low as 40 ms. Max Video Transmission Bitrate: 50 Mbps Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC) Operating Temperature Range: -10º to 40º C (14° to 104° F) Power Input: 7.4-26.4 V Audio Transmission: N/A  Includes 1x BOB57 6S HD BNF 2x Antennas 2x Battery pads 2x Prop(Pairs)

Read more less

All batteries must be shipped by a ground shipping method. Introducing iFlight's Defender 25, a sub-250 drone featuring the DJI O3 Air Unit. At 249g weight, Defender 25 doesn't require registration in most countries. The compact and lightweight design also make it easy to carry and store. It will be your best travel buddy to redefine your FPV adventure. The built-in 2.5-inch propeller guards were designed to fly boldly. You’ll experience a completely new creative freedom to fly whenever and wherever. The durable injection molded frame not only prevents damage to your motors or propellers but also protects the environment from small flight errors. Equipped with the latest tech from DJI, the O3 Air Unit HD transmission system, the Defender 25 supports 4K video and shoots up to 155° super-wide FOV footage for stunning visuals. In addition, D-Cinelike color mode provides more creative freedom for color grading, allowing you to edit and adjust your footage.  They’ve also added a special vibration-damped camera mount to keep your raw footage as smooth as possible, as well as ensure good Gyro Data for the built-in or in-post camera stabilization. Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products! Features Optimized Landing Gear for Take-Off in Complex Environments Built-in High-Performance video and Receiver Antennas 4K Stabilized Video with 155° Ultra-Wide Angle Crash-Protected Quick-Release Battery Countless Easy-to-Use Features Ultralight and Free to Fly Small and Mighty Specifications Defender 25 Product Name: Defender 25 4S HD Flight Electronics: BLITZ D25 F7 AIO Video Transmission: DJI O3 Air Unit Frame: 112±2mm Motor: Defender25 1404 Prop: Defender25 2525 props (2.5-inch) Weight of the Aircraft: 180g Takeoff Weight incl. 550mAh battery: ≤249g Dimensions (L×W×H)：158x155x69mm Max Ascent Speed: 6 m/s (Normal Mode, Sport Mode) Max Descent Speed: 6 m/s (Normal Mode, Sport Mode) Max Speed: 100Km/H (Manual Mode) Maximum Takeoff Altitude: 200 m Max Hover Time: Approx. 6 mins (with 550mAh battery), 10mins (with 900mAh battery) Max Flight Distance: 2-3 km Max Wind Speed Resistance: 80 Km/H (Level 5) Operating Temperature Range: -10° to 40° C (14° to 104° F) Transmission Power (EIRP): FCC: < 33 dBm / CE: < 14 dBm / SRRC: < 30 dBm Antennas: Dual Antennas GNSS: N/A Video Transmission Product Name: DJI O3 Air Unit Weight: Approx. 36.4grams Dimensions (L×W×H): L16.7×W103.9×H 81.3mm Screen Size (single screen): 0.49-inch Resolution (single screen): 1920×1080 Refresh Rate: Up to 100 Hz Interpupillary Distance Range: 56-72 mm Diopter Adjustment Range: -8.0 D to +2.0 D FOV (single screen): 51° Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz Transmission Power (EIRP): 2.4 GHz: < 30 dBm (FCC), < 20 dBm (CE/SRRC/KC) 5.8 GHz [4]: < 30 dBm (FCC), < 23 dBm (SRRC), < 14 dBm (CE/KC) Max Video Transmission Bitrate: 50 Mbps Operating Temperature Range: 0° to 40° C (32° to 104° F) Power Input: 7-9 V (1.5 A) Recommended (Not Included) iFlight Defender 25 Battery - 900mAh Includes 1x iFlight BNF Defender 25 HD 4S 2.5" Cinewhoop w/ DJI O3 Air Unit and DJI Camera (Pre-Built, Tuned, and Tested) 1x Defender 25 550mAh Battery 1x Charging Adapter Board 2x Defender 25 2525 Props (pairs)

Read more less

The iFlight Nazgul5 V3 6S 5" Freestyle Analog Quad is here! It includes the RaceCam R1 FPV Camera and Nazgul 5" tri-blade props, XING-E Pro 2207 motors, BLITZ F7 Flight Controller, BLITZ 1000mW+ VTX, and the BLITZ E45S 2-6S 45A BLHeli32 4-in-1 ESC. Boasting CNC aluminum camera mount with vibration-reduction silicone for increased protection. Great for freestyling and long-distance shots with your GoPro camera! The Nazgul5 Freestyle quad is a go-to gold standard for freestyle BNFs of great value made by the great people at iFlight.  The Nazgul5 V3 is a 5" freestyle frame is made of super stiff carbon for minimal resonance. + High-quality parts+ Sturdy frame structure+ Generous mounting space+ Optimized for O3 Air Unit+ GoPro camera mount included  Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products! Features XING-E Pro 2207 motors and NAZGUL F5 props 5" version also fits 5.1" style propellers Fits both 30.5x30.5 and 20x20 stacks 5mm arm design for more durability Popular True-X configuration LED illuminated logo TPU crash-guards Easy-Swap arms Specifications Product Name：Nazgul5 V3 6S Analog FC: BLITZ F722 FC ESC: BLITZ E45S 45A 4-IN-1 ESC Video Transmission: BLITZ 1mW+ VTX Frame: 245 ±2 mm wheelbase Motor: XING-E Pro 2207 motors Prop: Nazgul 5 inch propellers Takeoff Weight: Approx. 435g / 660±10g (With 6S 1400mAh Battery) Dimensions (L×W×H): 173×173×34±2 mm Diagonal Distance: 245mm Max Speed: 190 Km/h (Manual Mode) Maximum Takeoff Altitude: 3200 m Max Hover Time: Approx. 7.5 mins (No Load with 6S 1400mAh Battery) Max Flight Distance: 5 km Max Wind Speed Resistance: Level 7 Operating Temperature Range：-10° to 40° C (14° to 104° F) Antennas: Single Antenna Video Transmission System Product Name: BLITZ Whoop 1mW+ VTX Input voltage: 7V～34V Interface: MMCX Power levels: PIT/25mW/400mW/800mW/1600mW Channels: 40 (including Raceband) Mounting pattern: 30.5x30.5mm/Φ3 Lightweight: 18.9g (excluding antenna) VTX telemetry: IRC Tramp Betaflight IRC Tramp Configuration: Please download the attached VTX table for Betaflight! RC Tramp VTX table values: 25mW/400mW/800mW/1600mW Includes 1x Nazgul5 V3 6S Analog BNF 1x Antennas 2x Battery pads 2x Nazgul F5 Prop(Pairs)

Read more less

 The Nazgul5 HD V3 is loaded with lots of power and performance; it comes with the XING-E Pro 2207 6S motors, BLITZ F722 FC, and BLITZ E45S 45A 4-in-1 ESC, which makes this quad a must-have! Now with the DJI O3 Air Unit! The Nazgul V3 is one of the best freestyle frames for its value.  The Nazgul5 V3 HD has been pre-tuned and set up with everything you need, all you need to do is bind-and-fly. The Nazgul5 V3 is a 5" freestyle frame made of super stiff carbon for minimal resonance. Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products! Features XING-E Pro 2207 motors and NAZGUL F5 props 5" version also fits 5.1" style propellers Fits both 30.5x30.5 and 20x20 stacks 5mm arm design for more durability Popular True-X configuration LED illuminated logo TPU crash-guards Easy-Swap arms Specifications Operating Temperature Range：-10° to 40° C (14° to 104° F) Max Wind Speed Resistance: 130 Km/H (Level 4) Receiver: DJI BNF, ELRS Dimensions (L×W×H): 180×180×80 mm Max Speed: 130 Km/h (Manual Mode) Video Transmission: DJI O3 Air Unit Maximum Takeoff Altitude: 5000 m Product Name：Nazgul5 V3 6S HD ESC: BLITZ E45S 45A 4-IN-1 ESC Max Hover Time: Approx. 8 mins Motor: XING-E Pro 2207 motors Takeoff Weight: Approx. 620 g Prop: Nazgul 5 inch propellers Diagonal Distance: 245mm Frame: 255mm wheelbase Max Flight Distance: 5 km Antennas: 2 Antenna FC: BLITZ F722 GNSS: N/A Video Transmission  Product Name: DJI O3 Air Unit Weight: Approx. 36.4 grams（headband included） Dimensions (L×W×H): L32.5x W30.5xH 14.5mm Communication Bandwidth： Max 40 MHz FOV (single screen): 155° Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz End-to-End Latency With DJI FPV Goggles V2: 810p/120fps Video Transmission Quality: The latency is lower than 28 ms. 810p/60fps Video Transmission Quality: The latency is lower than 40 ms. With DJI Goggles 2: 1080p/100fps Video Transmission Quality: The latency is as low as 30 ms. 1080p/60fps Video Transmission Quality: The latency is as low as 40 ms. Max Video Transmission Bitrate: 50 Mbps Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC) Operating Temperature Range: -10º to 40º C (14° to 104° F) Power Input: 7.4-26.4 V Audio Transmission: N/A Includes 1x iFlight BNF Nazgul5 V3 HD  6S 5" Freestyle Quad w/ DJI O3 Air Unit & Micro Cam - Choose Receiver 2x Nazgul 5 inch propellers (Set of 4) 2x Battery Pad 2x Antenna

Read more less

Another solid choice in the Matek F405-miniTE 20x20 Flight Controller by a company that leads the pack when it comes to quality and performance. Check out all our 20x20 FCs as well as the entire Matek selection! Features F405 has 1MB flash which can run with ArduPilot.  even with INAV firmware. Redesigned target MATEKF405TE support 8x bi-directional DSHOT. Support DJI air unit PnP, and a 10V BEC for DJI OSD or analog VTX Compared with F722-miniSE 8motors or 6motor+2servos, F405-miniTE supports 8motors+3servos in INAV/BF multirotor mixer Convertible 20mm to 30.5mm mounting Specifications Input: 6~30V (2~6S LiPo) MCU: STM32F405RGT6 IMU: ICM42688-P OSD: AT7456E Baro: Goertek SPL06-001 (I2C) Blackbox: 16M-byte Flash memory UARTs: 6 PWM outputs: 12 (8 Dshot) I2C: 1 ADC: 4 (VBAT, Current, RSSI, Airspeed) Current Sensor: No PINIO: 2 BEC: 5V 1.7A & 10V 1.4A Mounting Pattern: 20x20 M2/M3, 30X30 M3 Weight: 5g Includes 1x Matek F405-miniTE 20x20 Flight Controller 1x 20mm to 30mm conversion plate(blue PCB) 6x Silicon grommets M4 to M3 6x Brass grommets M3 to M2 1x SH1.0_8pin cable 5cm (including 2x 8pin connectors) for 4in1 ESC 1x SH1.0_6pin to GH1.25_8pin cable 8cm for DJI Air Unit

Read more less

Introducing the smallest HD whoop with the DJI O3 currently on the market. This amazing 75mm quadcopter comes with the elite DJI O3 Air Unit and O3 Micro Cam, and the new BeeBrain BLV4 HD F7 AIO flight controller. Achieve sharper HD capture with amazing quality with O3 Air Unit. Boasting powerful 0804 12000kv dual ball bearings motors, despite its small size, this thing will rip!  Check out our other pre-built quads, as well as the rest of our NewBeeDrone selection. Explore and film spaces you never could before in HD! A must-have tool for professionals and hobbyists specializing in indoor space. The only HD Micro whoop board with F7 processor. Dual-bearing motors allow less friction in spinning while 3-blade Azi propellors were developed with engineering theory for optimal air-grab and stability. We master-tuned this drone to have the smoovest flight and absolutely no jello in any videos.  We found the best ratio between the size of drone and its weight distribution. Without DJI O3, the drone can fly up to 8 minutes. Up to 3 minutes with DJI O3 and battery. Choose between 3D printed battery mounts or strap.   We ensure that you get the best material and components  that are available so you can rely on the drone without troubleshooting or breaking. All parts are available separately as replacements. Additional flexibility with SLS Nylon prints allow cameras to be changed or updated if needed.  Assembly or tuning not required. Save time and energy so you can focus on your footage. Drone comes with built-in ExpressLRS and ready to pair. Built-in blackbox records data for tuning. Configure to DJI PNP on Betaflight if needed. Don't be afraid of messing up on customization. Reset to factory default (with our tunes and dump files) in one click if something is not right. Specifications  Drone Size: 75mm Flight Controller: BeeBrain BLV4 HD F7 Flight Controller ExpressLRS (ELRS) 2.4G Frame: Cockroach75 Brushless Frame Motors: Flow 0804 12000kv Double Ball Bearing Brushless Motor Propellesr: Azi (Tri-Blade) Micro Propellers 40mm - 1.0mm Shaft HD VTX & Camera: DJI O3 Air Unit Canopy: NewBeeDrone Acrobee75 HD O3 Canopy Total Weight without battery: 70.19g Total Weight with battery: 98.24g BeeBrain BLV4 HD F7 Flight Controller ELRS2.4G Specifications: MCU: STM32F745 ESC Firmware: S-H-40 - Bluejay, 0.19.2, 48kHz. ESC Specifications: 4 channel 12A ESC ESC Connector: JST-1.0 3Pin Weight: 6.6 grams (including antennas and battery connector) Size: Outer dimensions 29 x 29 x 7.6 mm Holes: 25.5 x 25.5 mm Battery input: 2S Connector: XT30 Internal Blackbox: 16MB Gyro: BMI270 UART1: SBUS on DJI Connector (RX only) UART2: TX & RX for internal ExpressLRS 3.0 receiver UART3: TX & RX for DJI MSP+Displayport Flight time with Tattu 450mAh 2S battery is 3:00min (at 7v)  Firmware:  BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune Includes 1x NewBeeDrone BNF AcroBee75 BLV4 2S HD 75mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz

Read more less

The ORT Helical 3 Turn 5.8GHz DJI Goggles 2 Antenna 2 Pack provides superior axial ratio performance compared to lower quality circular patch antennas. Its lightweight design makes it perfect for an FPV Goggles setup, and suitable for even the toughest RF environments, like those with buildings and trees that can block signals. Get industry-leading signal strength and penetration with ORT. Two sets of antennas with MCX male connectors for PNP on your DJI Goggles 2 to replace the default linear antenna. Pull out your default DJI Goggles 2 linear antennas' and plug in this fine tuned LHCP Helical 3 turn for a range boost & better penetration to run with your O3 compatible quads. Old Radio Transmission, is passionate about antenna’s that’s the reason why their antenna’s work flawlessly. They have tested the Helical 3 Turn whilst flying a whoop, the transition from indoor to outdoor flying was not an issue with these antennas! Check out all our FPV Receivers & Antennas and all our ORT antennas! Features Made in mind for the DJI Googles 2! Hand Tuned, providing wide beam width with 180 degree coverage and greater penetration through trees and dense material. High quality Enameled Supreme Wire (anti rust). Original Low loss RG402 cable. High quality acrylic, providing premium look. Effective range, 6~10km and beyond on 600mW Vtx (depends on flying area noise level, receiver sensitivity and FPV setup) Specifications  Freq Channel: 5300 ~ 6500 MHz Gain (dBi): 7 dBic SWR/S11: < 1:1.3 Beam width: 150deg Polarization: Circularly Polarized – LHCP Gain Pattern: Directional (needs to be pointed in the general flying area) Connector: MCX Male (for use with DJI Goggles 2) Weight: 26.7g ea. Includes 1x ORT Helical 3 Turn 5.8GHz DJI Goggles 2 Antenna 2 Pack - LHCP - Black

Read more less