In an effort to push the boundaries of carrying the camera on the smallest platform, Flywoo designed the smallest quadcopter possible in their history. The Firefly Baby Quad is a nano-sized FPV drone designed to carry an Insta360 Go, or SMO 4K cameras for some action flying. Weighing in at just 47g, the Firefly Baby Quad is small, flexible, and stable. It's full of power and offers unmatched control. Pilots can quietly enjoy the fun of shooting a video without jello. Perfect for the indoor and outdoor recording of every beautiful flying moment!
Check out our other pre-built quads, as well as other great products from Flywoo!
Specifications
Weight: 47g
Wheelbase: 80mm
FC & ESC : GOKU GN405 Nano 13A STACK ( 16x16 )
Frame: Firefly Baby Quad Frame (Analog Verison)
Motors: Nin V2 1203Pro 5500KV
Props: Gemfan 1636 40mm-4 V2.0
VTX: Goku VTX625 450mw
Antenna: Atomic 5.8GHz Antenna Length 30mm (RHCP)
Battery: 4S 450mAh / 4S 300mAh battery (Not including)
Flywoo GOKU GN405 NanoFlight Controller
MCU: STM32F405 BGA
IMU: ICM42688
UARTS: 6
Soft Serial Ports: 2
I2C: Yes
Onboard LED：WS2812x8(FCx4/ESCx4)
Supports: SBUS, iBus, Spektrum, Crossfire
BlackBox: 16Mb Flash
BEC: 5V Power Out: 2.0A max, 3.3V Power Out: 0.5A max
Dimensions: 22x22mm
Mounting Holes: 16x16mm
Weight: 2.3g
Flywoo GOKU BS13A 4in1 ESC
Support: Oneshot, Multishot, Dshot150, Dshot300, Dshot600
Input Voltage: 2-4S Lipo
Continuous Current: 13A
Firmware: BLHELI_S
Mounting Pattern: 16x16mm, M3 Hole
Weight: 2.5g
Nin V2 Motor
Stator Size: 1203
KV: 5500
Goku VTX625 450mw
Raceband: 5362-5945 MHZ
Power: PIT/25/50/100/200/450mW switchable
Input Voltage: 5V
Control Mode: IRC Tramp(RX) & Button
Video System: NTSC/PAL
Antenna: IPEX (U.FL)
Size: 30mmx30mmx4mm
Weight: 1.3g
Includes
1x Flywoo BNF Firefly Baby V1.3 4S 1.6" Analog Micro Quad - Choose Receiver
Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the great capabilities of HDzero System.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Dead Cat Style
The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers.
New Design
Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Efficient Power Combo
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
Ultra-light AIO with ELRS 2.4G RXThe drone's GOKU Versatile F411 VTX 1S AIO V2 includes a built-in 250mW video transmitter, enabling an extended flight range and ultimate lightweight design without sacrificing performance, with improved circuit board stability.
HD Digital VTX System
The HDZero Nano Lite Camera is a revolutionary product designed for lightweight drones, weighing only 1.5g and combined with the new Whoop Lite VTX at 4.5g. Supporting 1-3S power input, it can record in 720P/60FPS with ultra-low latency of less than 19ms and features OSD function configuration through Betaflight Configurator.
More Power, More Flight Time
The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed.
Specifications
Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit
Motor: ROBO 1002 19800KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Propeller: 1608-3 Blade 40mm 1.5mm Shaft
Camera: Nano Lite Cam
Weight: 31g
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
ROBO 1002 19800KV
Configuration: 9N12P
Stator Diamter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.3
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 44
Internal Resistance: 89mΩ
Max Current(3S): 11.8A
Max Efficiency Current: (2-4A)>84%
HDZERO WHOOP LITE VTX
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Resolution: 1280x720@60fps
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Weight: 7g total package
HDZERO NANO LITE CAMERA
Size: 14x16x11mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor
FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65°
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz
4x 1608 -3 40mm 1.5mm shaft
2x TPU battery mount
1x hardware screws set
4x Prop guards
Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the elite capabilities of HD Walksnail System.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Dead Cat Style
The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers.
New Design
Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Efficient Power Combo
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
Ultra-light AIO with ELRS 2.4G RX
The drone's GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. This allows for the ultimate lightweight design without sacrificing functionality.
HD Digital VTX System
The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting.
More Power, More Flight Time
The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed.
Specifications
Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit
Motor: ROBO 1002 19800KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Propeller: 1608-3 Blade 40mm 1.5mm Shaft
Camera: Avatar Lite Cam
Weight: 33g
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
ROBO 1002 19800KV
Configuration: 9N12P
Stator Diamter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.3
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 44
Internal Resistance: 89mΩ
Max Current(3S): 11.8A
Max Efficiency Current: (2-4A)>84%
Walksnail Avatar HD Mini 1S Lite
Model: Avatar mini 1s module
Communication Frequency: 5.725-5.850GHz
Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm;
MIC:<25dBm
I/O Interface: JST1.0x6(Power in)JST1.0x4(USB)
Mounting Holes: 25.5x25.5mm
Dimensions: 30x30x6.5mm
Storage: 8G
Recording: 1080p/720p
Weight: 5.1g
Operating Temperature: -20-40℃
Channels: 8
Wide Power Input: 3.1V-5V
Supported FC System: Betaflight
OSD: Canvas mode
Bitrate: 25mbps, 50mbps
Latency Average delay: 22ms
Antenna: IPEX
Avatar lite camera
Model: Avatar lite camera
Image Sensor: 1/2.7”1nch
Resolution: 1080P/60fps,720P/120fps,720P/60fps
Ratio: 16/9 4/3
Lens:2.1mm
FOV:170°
Aperture:F2.0
Shutter Rolling: Rolling shutter
Min.Illumination: 0.001Lux
Weight: 1.8g
Dimensions: 14x14x16mm
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz
4x 1608 -3 40mm 1.5mm shaft
2x TPU battery mount
1x hardware screws set
4x Prop guards
The FR16 Nano Baby V2 is a meticulously crafted microdrone with improved appearance, flight time, and power compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy reinforces camera protection, while a new bottom plate adds sturdiness and crash resistance. The drone is equipped with a special gold-purple edition ROBO 1002 23,500KV motor and GOKU Versatile F411 VTX 1S AIO V2 with 250mW video transmitter. The Flywoo 1S Nano camera V3 delivers clearer and better image quality on this quad.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
Ultra-light GOKU Versatile F411 1S VTX AIO V2 with upgraded circuit board stability and a 250mw video transmitter, enabling an extended flight range.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
Upgraded Flywoo 1S Nano camera V3 delivers clearer and better image quality.
New battery compartment design allows for easy replacement of batteries of different models.
Specification
Motor: ROBO 1002 23500KV
Electronics: GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/250mW VTX
Props: 1609 - 4 blade 40mm 1.5mm Shaft
Camera: Flywoo 1S Nano Camera V3
Receiver: ExpressLRS 2.4GHz
Weight: 26g
Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate)
Speed: 80km/h (approximate)
GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/ 250mw VTX
Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port：1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HV Current: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
Onboard 5.8g VTX
Output power: 25mw~250mw switchable
Frequency: 40CH
Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready
Flywoo ROBO 1002 23500KV Fpv Motor:
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.5
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 52
Internal Resistance: 75mΩ
Max Current(3S): 14A
Max Efficiency Current: (2-4A)>84%
Flywoo 1S Nano Camera V3
Model: Flywoo 1S Nano Camera V3
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC and PAL(switchable)
MENU: Support
IMAGE: 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio: >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm/F2.5
Min. illumination: 0.001Lux
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14x14mm
Wide Power Input: DC 3.7-18V
Work Temperature: -20°C~+60C
Work Humidity: 20%~80%
Weight: 2.1g
Includes
1x Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz
4x 1609 - 4 40mm 1.5mm shaft
2x TPU Battery Mount
1x Hardware Screw Set
4x Prop guards
The Firefly 1S Nano Baby V2 is a micro-drone with improved flight time, power and design compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy for camera protection and a bottom plate for sturdiness are integrated. Additionally, this model includes the GOKU F411 ELRS 1S AIO V2 with ELRS 2.4G receiver (UART 2) for a lightweight design with optimal performance. This version utilizes the elite capabilities of the HDZero HD digital VTX system. The HDZero Nano Lite Camera is a revolutionary product designed for lightweight drones, weighing only 1.5g and combined with the new Whoop Lite VTX at 4.5g. Supporting 1-3S power input, it can record in 720P/60FPS with ultra-low latency of less than 19ms and features OSD function configuration through Betaflight Configurator.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features:
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds - perfect for racing competitions.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Specifications
Motor: ROBO 1002 23,500KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Props: 1609 - 4 blade 40mm 1.5mm Shaft
HD Digital VTX System: HDZero Whoop Lite Bundle
Receiver: ExpressLRS 2.4GHz
Weight: 31g
Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate)
Speed: 70km/h (approximate)
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
Flywoo ROBO 1002 23500KV Fpv Motor:
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.5
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 52
Internal Resistance: 75mΩ
Max Current(3S): 14A
Max Efficiency Current: (2-4A)>84%
HDZero Whoop LITE VTX
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Resolution: 1280x720@60fps
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Weight: 7g total package
HDZero Nano LITE Camera
Size: 14x16x11mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor
FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65°
Includes
1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz
4x 1609 - 4 40mm 1.5mm shaft
2x TPU Battery Mount
1x Hardware Screw Set
4x Prop guards
The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system. The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Specification
Motor: ROBO 1002 23500KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Props: 1609 - 4 blade 40mm 1.5mm Shaft
HD Digital VTX System: Walksnail Avatar HD Mini 1S Lite
Receiver: ExpressLRS 2.4GHz
Weight: 33g
Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate)
Speed: 70km/h (approximate)
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
Flywoo ROBO 1002 23500KV Fpv Motor:
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.5
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 52
Internal Resistance: 75mΩ
Max Current(3S): 14A
Max Efficiency Current: (2-4A)>84%
Walksnail Avatar HD Mini 1S Lite
Model: Avatar mini 1s module
Communication Frequency: 5.725-5.850GHz
Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm;
MIC:<25dBm
I/O Interface: JST1.0x6(Power in)JST1.0x4(USB)
Mounting Holes: 25.5x25.5mm
Dimensions: 30x30x6.5mm
Storage: 8G
Recording: 1080p/720p
Weight: 5.1g
Operating Temperature: -20-40℃
Channels: 8
Wide Power Input: 3.1V-5V
Supported FC System: Betaflight
OSD: Canvas mode
Bitrate: 25mbps, 50mbps
Latency Average delay: 22ms
Antenna: IPEX
Avatar lite camera
Model: Avatar lite camera
Image Sensor: 1/2.7”1nch
Resolution: 1080P/60fps,720P/120fps,720P/60fps
Ratio: 16/9 4/3
Lens:2.1mm
FOV: 170°
Aperture: F2.0
Shutter Rolling: Rolling shutter
Min.Illumination: 0.001Lux
Weight: 1.8g
Dimensions: 14x14x16mm
Includes
1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz
4x 1609 - 4 40mm 1.5mm shaft
2x TPU Battery Mount
1x Hardware Screw Set
4x Prop guards
Flywoo's Firefly Hex Nano V1.2 is the smallest hexacopter ever designed by Flywoo, weighing in at 74g. It powerfully and stably carries Insta 360go and SMO 4K cameras. The Firefly hex nano is small, flexible, stable, and is full of power and offers unmatched control.
Check out our other pre-built quads, as well as other great products from Flywoo!
Feature
Hexacopter
HD system
Naked Vista
Weighing only 74 grams
Built in SMO Power Cable
Prebuilt and tested
Specifications
Weight: 74g
Wheelbase: 80mm
FC & ESC:【No.C203】GOKU HEX F4 16x16 STACK - ( FC+13A ESC ) ( MPU6000)
Frame: Firefly Baby Quad Frame (HD Verison)
Motors: Nin V2 1203Pro 5500Kv
Props: Gemfan 1636 40mm-4 V2.0
HD digital camera & VTX: Naked RunCam Link & RunCam Wasp
Antenna: Atomic 5.8GHz Antenna Length 30mm (LHCP)
Battery (Recommended): 4S 450mAh / 4S 300mAh battery (Not including)
GOKU HEX GN405 Nano16X16 FC
MCU: STM32F405 BGA
IMU: ICM42688P
Barometer: DPS310
input voltage： 2-6S
Onboard LED：WS2812x4
6 hardware UARTS (UART1,2,3,4,5,6)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only.
PPM and PWM receivers are not supported.
Onboard 16Mbytes for Blackbox logging
5V Power Out: 2.0A max
3.3V Power Out: 0.5A max
Dimensions: 22x22mm
Mounting Holes: 16x16mm
Weight: 2.3g
Firmware : FLYWOOF405NANO
BS13A BLheli_S 2-4S 4in1
lBS20/35A BLheli_S 2-6S 4in1
Weight: 2.5g
Mounting Hole: 16x16mm (M3)
Support Oneshot, Multishot,
DShot150/300/600
Nin V2 Motor
Stator Size: 1203
Motor Bolt Pattern: 9x9mm
KV: 5500
Wasp Nano HD Camera
Dimensions: L18mmxW14mmxH18mm
LENS: FOV D:160° H:127° V:92°
Resolution: 720P@120fps(4:3)
Net Weight: 6g(With Cable)
Shutter: Rolling Shutter
Coaxial Cable: 80 mm
Image Sensor: 1/3"
Naked Link Air Unit
Input Voltage: 7.4-26.4V@ 4-9W
Operating Frequency: 5.725-5.850 GHz
Transmitter Power: (EIRP) FCC/SRRC: <30 dBm; CE: <14 dBm
Min. Latency (end-to-end): 1280 x 720 60fps: 32 ms
Max. Transmission Distance: FCC/SRRC: 4 km; CE: 0.7 km;
I/O Interface: Type-C, IPEX, 3-in-1 port,
Supported Flight Control System: BetaFlight
Operating Temperature Range: 0° to 40° C (32° to 104° F)
Includes
1x Flywoo BNF Firefly Hex Nano V1.2 1.6" HD 4S Micro Quad w/ Naked RunCam Link & RunCam Wasp - Choose Receiver
1x Accessories (props, prop guard, RunCam link shell, battery straps, hardware, ect)
Build your own version of the Firefly DC16 micro quad, with this micro frame kit.
Check out our other Micro frames, as well as other great products from Flywoo!
Feature
Compatible with 40mm propellers
Specifications
Weight: 3.7g
Motor Bolt Pattern: 6mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 1.6" Analog Micro Frame Kit
Build your own version of the Firefly DC16 micro quad, with this micro frame kit.
Check out our other Micro frames, as well as other great products from Flywoo!
Feature
Compatible with 40mm propellers
Specifications
Weight: 3.7g
Motor Bolt Pattern: 6mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 1.6" HDzero Micro Frame Kit
Build your own version of the Firefly DC16 micro quad, with this micro frame kit.
Check out our other Micro frames, as well as other great products from Flywoo!
Feature
Compatible with 40mm propellers
Specifications
Weight: 3.7g
Motor Bolt Pattern: 6mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 1.6" Walksnail Micro Frame Kit
Build your own version of the Firefly FC16 micro quad, with this micro frame kit.
Check out our other Micro frames, as well as other great products from Flywoo!
Feature
Compatible with 40mm propellers
Specifications
Weight: 3.8g
Motor Bolt Pattern: 6mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Flywoo BNF Firefly FR16 Nano Baby V2.0 1.6" Analog Micro Frame Kit
FMM129P, FMS ASW-17 EP Glider PNP 2500mm
Features
Two piece wing
Functional Flaps
Made of highly durable EPO
Fold away high efficiency propeller
Snap together assembly, no glue necessary
Overview
True to the FMS spirit, no detail was overlooked in the design of the ASW-17. The FMS engineers made 4 expensive tooling adjustments just to micro-adjust the airfoil for perfect efficiency. The wing, vertical and horizontal stabilizers are designed with a snap-together structure. With a simple snap, the surfaces attach to the fuselage with pinpoint precision- no screws or glue necessary! Build the aircraft in as little as 3 minutes! Like the 3000mm Fox, the ASW-17 has a pre-installed carbon fiber spar that ensures wing rigidity in high-G maneuvers.
To achieve the same dihedral as the real aircraft, the ASW-17 was designed with a specialized CNC aluminum spar joiner- allowing the aircraft to maintain its wing geometry during demanding flight routines. Performance-wise, a high-quality Hobbywing 40A ESC paired with a Predator 3541-750KV motor provides ample power with a 4S pack to perform most aerobatic maneuvers. If efficiency, stability and aerobatic capabilities are what you seek in a glider, look no further than the FMS 2500mm ASW-17!
Needed to Complete
14.8V 2200-2600mAh 35C Battery
6-Channel Radio
6-Channel Receiver
What's in the Box?
(1) ASW-17 EP Glider PNP
(1) Hobbywing 40A ESC
(1) Predator 3541-750KV motor
(1) Product Manual
This product was added to our catalog on December 9, 2023
Taking your drone photography to the next level, the new series Cinebot30, take you to the real world, shooting extreme footage.
Cinebot30 is a new generation of Cinematic FPV drone developed by GEPRC team. The high-strength 7075 aircraft-grade aluminum alloy bracket for FPV camera escort, the combination of classic engineering and aesthetics. The newly polished gimbal damping module can easily fix high-frequency vibration and jello issues. It can be mounted with GEPRC Naked GoPro Hero 8 and GoPro Black Bones, Insta 360 GO2 and other cameras. The image is stable and clear, and it’s easy to film.
Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!
Cinebot30 will be equipped with a powerful 1804 motor with optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmx3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations. Finely polished frame design, only 6 screws need to be removed to separate the aircraft top plate and protection frame. Easy to cope with the urgent need to replace the accessories, at any time to restore the state.
Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Design that combines engineering and aesthetics.
Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts.
Selected high-toughness and impact-resistant PC material for injection molding.
Aviation 7075 aluminum alloy camera mounting bracket and fuselage aluminum column.
Propeller guard embedded ring Cob light strip, carefully tuned light effect. Color brightness in the day and night can be clearly displayed.
The newly developed gimbal shock absorption structure can disintegrate high frequency jitter and jello effect. Easily carry a variety of action cameras.
Powerful 1804 motor, surging torque to deal with ultra-low altitude flight at will.
With the new GEP-F722-45A AIO V2, stable performance, more secure flight
Four kinds of FPV system with the program, choose to belong to your first-person view
Tuned by GEPRC professionals, delicate and silky flying feel
Specifications
Input Voltage: 3-4S
Wheelbase:127mm
Isolation Plate:2mm
Main plate:3mm
Bottom plate:1.5mm
Motors: SPEEDX2 1804-3450KV
Propellor: HQ prop T76mmx3 propeller
VTX: GEPRC RAD 1W
Antenna: Peano 5.8G 110mm RHCP MMCX Antenna
Camera: Caddx ratel 2
Weight: 206.4g
GEPRC GEP-F722-45A AIO
Model: Cinebot30 HD Nebula PRO Quadcopter
Gyro: BMI270/42688 gyro/accelerometer(SPI)
OSD: Yes
ESC Connections: Yes
Firmware: GEP-F722-45A AIO
BEC: 5V 1A
Current Sensor: Yes
Buzzer: no
Barometer: No
Input Voltage: 2-4S LiPo
MCU: STM32F722RET6
IMU: ICM-42688-P
Stack Size: 25x25mm
Dimensions: 32x32xmm
Weight: 8.8g
Includes
1x GEPRC BNF CineBot30 4S 3" Analog Cinewhoop - Choose Version
2 x HQProp T76MM（pair）
1 x Battery strap M15x200mm
1 x Battery strap M15x220mm
2 x Battery Silicone Pads
1 x Set of screws
1 x Set of screwdrivers
1 x GoPro camera mount holder
1 x Set of screws
1 x Set of screwdrivers
1 x Antenna fixed tube
Since DJI released the O3 AIR Unit FPV high-definition video transmission system, the GEPRC team has followed closely to make the latest set of the O3 AIR Unit system, the Cinebot30 HD O3 AIR Unit version. The Cinebot 30 is a new generation of cinematic FPV drones developed by the GEPRC team.
The aluminum parts of the camera are still made of high-strength 7075 aircraft-grade aluminum alloy materials. The TPU shock-absorbing pad is designed on the bracket structure, which can excellently isolate the high-frequency vibration of the fuselage so that the camera can still obtain jelly-free high-definition images during high-speed flight The installation of the video transmission has also designed an assembly scheme, which allows the O3 video transmission to be completely installed inside the fuselage without affecting the Type-C USB data cable connected to the Air Unit to read video data. O3 Air Unit is currently the most advanced FPV system on the market. It can transmit 1080P 60fps real-time images, and can also record up to 4K 60fps images with an anti-shake effect at the same time.The upgraded video transmission system also combines market feedback to upgrade the gimbal top plate of the fuselage, which is compatible with the camera base fixed by 4-hole screws, so that Cinebot30 can mount a full-sized GoPro camera very well, and the battery life can reach 5 minutes and 30 seconds. However, the GEPRC team recommends flying with Naked GoPro 10, with a battery life of up to 10 minutes and 30 seconds.Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!Cinebot30 will be equipped with a powerful 1804 motor with an optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmX3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations.Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots!
Features
Adopts the most advanced O3 Air Unit FPV digital video transmission system on the market
Video transmission with high-definition anti-shake 4K 60fps ultra-high resolution video quality
The highest bit rate is 50MBPS, the delay is as low as 30 milliseconds, and the highest image quality is 1080P 60FPS
Upgraded the top plate of the fuselage gimbal, compatible with the camera base fixed by 4-hole screws, and supports mounting a full-sized GoPro camera for flight
The camera aluminum mechanism is designed with TPU shock absorption, which can effectively eliminate the image jello caused by the vibration of the body
The ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. Color brightness can be clearly displayed in day and night
Selection of high-quality high-toughness, impact-resistant PC&PET material injection molding
Powerful 1804 motor, surging torque to cope with ultra-low altitude flight
Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts
With the new GEP-F722-45A AIO V2, the performance is stable and the flight is more secure
Tuned by GEPRC professionals, delicate and silky flying feel
Specifications
Model: Cinebot30 HD O3 Quadcopter
Brand: GEPRC
Frame: GEP-CT30 O3
Wheelbase:127mm
Isolation Plate:2mm
Main plate:3mm
Bottom plate:1.5mm
FC: GEP-F722-45A AIO V2
MCU: STM32F722RET6
IMU: ICM-42688-P
VTX: DJI O3 Air Unit
Video resolution: 4K@50/60fps, 2.7K@50/60/100/120fps, 1080p@50/60/100/120fps
Camera: DJI O3
Propeller: HQ prop T76mmx3 propeller
Antenna: DJI O3 Antenna
Charge connector: XT60H-M
Motor: SPEEDX2 1804-2450KV（6S Version）/ SPEEDX2 1804-3450KV（4S Version）
Weight: Nebula Pro version 222.5g / Avatar version 221g / Analog version 209.2g / Link Wasp version 222.5g / O3 version 234.7g (excluding battery, the above are TBS Nano RX version)
Receiver: PNP, Frsky R-XSR, TBS Nano RX, ELRS 2.4G
Recommended Battery: LiPo 4S 1100mAh-1300mAh (4S Version) / LiPo 6S 850mAh-1100mAh(6S Version)
Includes
1x Cinebot30 HD O3 Quadcopter
2x HQProp T76MM（pair）
1x Battery strap M15x200mm
1x Battery strap M15x220mm
2x Battery Silicone Pads
1x Set of screws
1x Set of screwdrivers
1x GoPro camera mount holder
1x Set of screws
1x Set of screwdrivers
1x Antenna fixed tube
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market.
The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life.
It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras.
Find the recommended 4S 450-750mAh batteries here!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect.
Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning.
2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting.
SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried.
Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted.
The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible.
Specifications
Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz
Frame: GEP-CL20
Wheelbase: 100mm
Gimbal plate: 2.0mm
Top plate: 2.5mm
Bottom plate: 1.5mm
FC system: GEP-F411-35A AIO
MCU: STM32F411CEU6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 35A
VTX: GEPRC 5.8GHz@600mW
Camera: Caddx Ratel2
Antenna: GEPRC Peano 5.8G RHCP MMCX
Motor: GR1303.5 5500KV
Propeller: EMAX Avan Micro 2×2.4×4
Receiver: ELRS2.4G
Recommended battery: LiHv 4S 450mah-660mah
Flight time: 4-6min
Includes
1x CineLog20 Analog
2x 2-inch propellers (pairs)
1x Naked GoPro Base
2x M15×150mm battery strap
2x Battery Silicone Pads
2x EVA Landing Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x Antenna fixed tube
1x 4S Naked GoPro power cable (with balanced terminal head)
2x EVA damping rings of guards
1x TBS Antenna mount (Vertical Type)
1x TBS Antenna mount (Horizontal Type)
1x TBS Antenna printed parts
The screw package includes:
3x M2×12mm cup head screws
2x M2×5mm round head screws
1x M2×8mm round head screw with pad
3x M2×7mm round head screws
2x M2×8mm round head screws
2x M2 iron nuts
1x self-clinching nut
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog four mainstream video transmission systems on the market.
The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 AIR Unit shooting, which can achieve an excellent anti-shake effect. The O3 Air Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life.
It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras.
Find the recommended 4S 450-750mAh batteries here!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect.
Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning.
2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting.
SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried.
Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted.
The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible.
Specifications
Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz
Frame: GEP-CL20
Wheelbase: 100mm
Gimbal plate: 2.0mm
Top plate: 2.5mm
Bottom plate: 1.5mm
FC system: GEP-F411-35A AIO
MCU: STM32F411CEU6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 35A
VTX: Link
Camera: RunCam Wasp
Antenna: GEPRC Peano 5.8G LHCP U.FL
Motor: GR1303.5 5500KV
Propeller: EMAX Avan Micro 2×2.4×4
Receiver: PNP (built-in DJI receiver), ELRS2.4G
Recommended battery: LiHv 4S 450mah-660mah
Flight time: 4-6min
Includes
1x CineLog20 HD Wasp
2x 2-inch propellers (pairs)
1x Naked GoPro Base
2x M15×150mm battery strap
2x Battery Silicone Pads
2x EVA Landing Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x Antenna fixed tube
1x 4S Naked GoPro power cable (with balanced terminal head)
2x EVA damping rings of guards
1x TBS Antenna mount (Vertical Type)
1x TBS Antenna mount (Horizontal Type)
1x TBS Antenna printed parts
The screw package includes:
3x M2×12mm cup head screws
2x M2×5mm round head screws
1x M2×8mm round head screw with pad
3x M2×7mm round head screws
2x M2×8mm round head screws
2x M2 iron nuts
1x self-clinching nut
Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5" Cinewhoop. This powerful model features an analog & micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch.
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
New appearance design, strengthening carbon plate, hollow design, injection protection frame, noise reduction design, flight safety, silent.
Adopts the GEP F722-45A AIO V2 high performance flight controller.
SPEEDX2 2105.5 motor with HQ DT90 propeller, stable power output, and smooth flight feel.
Power cable using XT60E1-M plug and carbon plate integrated design, convenient application.
Battery installation method using a tie with 7075 aluminum parts fixed, solid and stable.
Carefully tuned 3.5-inch cinematic FPV quad with flexible and delicate flight feeling.
Pre-Installed with a M8U GPS
Specifications
Model: Cinelog35 V2 Analog
Frame: GEP-CL35 V2
Wheelbase: 142mm
Gimbal Plate: 2.0mm
Top Plate: 3.5mm
Bottom Plate: 1.5mm
FC system: GEP-F722-45A AIO V2
MCU: STM32F722RET6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 45A
VTX: GEPRC RAD 1W(UFL)
Camera: Caddx Ratel2
Antenna: GEPRC Peano 5.8 RHCP UFL
Motor: SPEEDX2 2105.5-2150KV (6S)
Propeller: HQProp D-T90MM
GPS: GEP-M8U
Receiver: ELRS2.4G
Weight: 262g
Recommended battery: LiPo 1050mah-1300mah
Flight time: 5′00″ - 8′ 30″
Includes
1x GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS)
2x HQProp D-T90MM（2 pairs）
2x M20 x 250mm battery strap
2x Battery Silicone Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x L-shaped screwdriver (2mm)
1x L-shaped screwdriver (3mm)
1x M5 wrench
1x plastic tweezers
1x Antenna fixed tube (pair)
1x Keychain
1x GP Camera Mounting Base
1x Naked GP Camera Mounting Base
1x Antenna Mounting Base
The GEPRC team has an amazing history of pushing boundaries and redefining standards in long-range FPV. Introducing the Crocodile75 V3: designed for comfort and stability, with a novel appearance, O3 Air Unit and special cooling components for efficient cooling, SPAN G50A BLHeli_32 4IN1 ESC, and 2806.5 1350KV motor and expertly tuned performance. Experience the passionate flight of the Crocodile75 V3! The battery plug is integrated with the fuselage for convenient application. The overall performance of Crocodile75 V3 has been carefully and strictly tuned by the GEPRC team to bring the most passionate flying experience for pilots.
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Adopt a novel appearance design, strengthen the fuselage structure, and reduce the impact of fuselage vibration on the gyroscope sampling data.
Equipped with SPEEDX2 2806.5 1350KV motor and HQ7.5×3.7×3 with sufficient power and high efficiency.
Upgrade the ESC to SPAN G50A BLHeli_32 4IN1.
Add protective side panels to effectively protect the electronic control system from instability caused by sand and dust pollution
The integrated design of the battery plug and the body simplifies the power-on operation, simplicity and beauty.
Equipped with O3 Air Unit and added special heatsink, excellent heat dissipation, to avoid O3 Air Unit overheating and stop recording.
The Crocodile75 V3 has a lengthier fuselage, can be mounted with Lipo 6S 3300mah-4500mah or Lion 6S 6000mah battery for flight.
Perfect match for 7-inch or 7.5-inch propellers
Specifications
Specifications
Model: Crocodile75 V3 HD O3
Frame: GEP-LC75 V3
Wheelbase: 342mm
Top plate: 2.5mm
Bottom plate: 3.0mm
Arm plate: 6.0mm
Splint plate: 2.5mm
FC: SPAN F722-BT-HD V2
ESC: SPAN G50A BLHeli_32 4IN1
MCU: STM32F722RET6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
VTX: O3 Air Unit
Camera: O3
GPS: GEP-M8U
Antenna: Momoda 5.8G LHCP RP-SMA x2
Motor: SPEEDX2 2806.5 1350KV
Propeller: HQProp7.5x3.7x3
Weight: 628.5g
Receiver: GEPRC ELRS 2.4G
Recommended battery: Lipo 6S 2600mah-4200mah / Lion 6S 6000mah
Flight time: 12-30 min
Includes
1x GEPRC BNF Crocodile75 V3 HD LR 6S 7" Long Range Quad w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz (GPS)
4x HQProp7.5x3.7x3
2x M20x250mm battery straps
2x Battery Silicone Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x L-shaped screwdriver (2mm)
1x L-shaped screwdriver (3mm)
1x M5 wrench
1x GEPRC Keychain
1x GP Camera Base
Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season. This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability.
Check out the rest of pre-built quads and our HappyModel selection!
Features
X12 5-IN-1 AIO flight controller w/ built-in receiver and OpenVTX
VTX Power up to 400mw
RS0802 20000KV motors
RunCam Nano 3. The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible with 1S Lipo/LIHV
Specifications
Input Voltage: 1S
Max Continuous Current: 12A
Motors: 0802 20000KV
Camera: RunCam Nano 3
Wheelbase: 75mm
Dimensions: 99x99x40mm
Weight: 24g
Includes
1x HappyModel BNF 1S Mobula 7 Whoop - PNP
The HappyModel BNF 1S Mobula 7 HD Whoop version is a light and efficient 75mm brushless whoop which provides 1080P HD video recording functionality. HappyModel added blackbox for this 1s 75mm HD recording whoop so that you now have gyroflow functionality. Unlock the ultimate smooth flights with a combination of the Mob 7 HD and gyroflow!
Check out the rest of pre-built quads and our HappyModel selection!
Specifications
HappyModel X12 AIO
Input Voltage: 1-2S
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: MPU6000 or ICM20689 or BMI270
Max Continuous Current: 12A
VTX Output Power: 25-400mW
Antenna Connector: U.FL
OSD: Yes
Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX
ESC Firmware: Z_H_30_REV16_7
Mounting Pattern: 25x25mm
Weight: 5.1g
HappyModel RS Motor
Input Voltage: 1S
KV: 20000KV
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension: Φ10.5x13.5mm
Wire length(include connector): 30mm
Weight: 2g
Runcam Split 3 Lite
Video Resolution: 1080@60fps/1080@50fps/1080@30fps/720@60fps
Field of View(FOV): Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video File Format: MOV
Image Resolution: 2MP
Signal System: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Includes
1x HappyModel BNF 1S Mobula 7 HD Whoop
The Crux 35 is an ultra-lightweight 3.5Inch FPV freestyle and racing drone, the weight of the whole drone is only 87g for the analog version and 108g for the digital HD version. The Crux35 series drone use Happymodel's EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
Happymodel Crux35 Racing Drone V2 comes with the CrazyF411 ELRS flight controller. This board comes with an integrated UART 2.4GHz ExpressLRS receiver and 20A BLheli_S ESC(Bluejay firmware pre-installed) which could support 3-4S.
The new V2 version comes with CrazyF411 ELRS AIO flight controller built-in UART ExpressLRS receiver which allows for updating the receiver with ease.
Choose from between ELRS 2.4GHz and FrSky for your receiver.
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Features
Bind tutorial for ELRS
Ultra-lightweight 3.5-inch BNF FPV Freestyle Drone
HD video transmission and analog video transmission are optional
Integrated ExpressLRS UART receiver
High efficiency EX1404 power system
Can be equipped with Naked Gopro or SMO4K
Specifications
Weight: 87g
Brand: Happymodel
Wheelbase: 150mm
Dimensions: 130mmx130mmx45mm
Receiver option: UART ExpressLRS 2.4GHz
HappyModel Flight Controller (ELRS Version)
Input Voltage: 2-4S LiPo
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: BMI270 or ICM42688P (SPI control)
ESC Connections: Yes
Firmware: CrazybeeF4DX
Current Sensor: Yes
Mount pattern: 25.5x25.5mm (M2)
Dimensions: 32x28x9mm
Weight: 5g
Built-in 20A Blheli_s ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1A BEC
Onboard ESC:
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite and ESC-Configurator programmable
Factory firmware: Bluejay 0.18.1
Firmware target: F_H_40_48_v0.18.1
Support DSHOT150/DSHOT300/DSHOT600
Default protocol: DSHOT300
HappyModel EX1404 3500KV Motor
Mode: EX1404
Kv: 3500Kv
Input Voltage: 3-4S LiPo
Configuration: 9N12P
Motor Dimensions: Φ17.8mm x 17.6mm
Stator Dimensions: Φ14mm x 4mm
Shaft Diameter: 1.5mm
Mounting Pattern: Φ9mm
Weight: 9g
HappyModel Propellers
Propeller Diameter: 3.5 inch
Pitch : 2
Blades : 3
Material : Poly Carbonate
Weight : 1.5g
Hub Diameter : 10mm
Hub Thickness: 4.7mm
Shaft :1.9/1.5/1.9mm
Adaptor Rings : NO
Caddx Ant Camera
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC and PAL(switchable)
MENU: Support
IMAGE: 4:3 or 16:9
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio: >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm/F2.5
Minimum illumination: 0.001Lux
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14x14mm
Wide Power Input: DC 3.7-18V
Work Temperature: -20°C~+60C
Work Humidity: 20%~80%
Weight: 1.7g
Happymodel OVX303 5.8G analog VTX or OVX306 5.8G analog VTX
Input Voltage: 5V
RF Output Power: 25-300mW
Antenna Connector: U.Fl
Power/Video Connection: Solder Pads
OVX303 Stack Size: 16x16mm, 20x20mm, 25x25mm
OVX306 Stack Size: 25x25mm
Weight: 0.9~1g
Includes
1x HappyModel BNF Crux35 V2 3.5" Analog Quad - Choose version
1x 5D-OSD menu board
1x Screw Driver and Screw Set
8x HQProp T3.5X2X3Grey (4cw+4ccw)
1x Buckle Velcro for battery
Introducing the Moblite7 Ultralight FPV Brushless Whoop! Made in collaboration with FPV pilot "Mr. Shutterbug," this whoop is one of the lightest 75mm drones on the market! And glows in the dark!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 36g With battery
Propellor Size: 75mm
Antenna: Linear Dipole
HappyModel DiamondF4 FR FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CrazybeeF4F
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (3sec)
ESC Firmware: BLheli_S
Factory firmware: O_H_50_REV16_8.HEX
Stack Size: 25x25mm
Dimensions: 29x29mm
Motors
Stator Size: 0802
Kv: 19000
Weight: 1.7g
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x 75mm Frame (Mobula7 frame)
1x Option1: DiamondF4 FR built-in SPI Frsky receiver
4x EX0802 KV19000 Unibell brushless motor
1x HQPROP 40MMX2 propeller(4cw+4ccw)
1x Runcam Nano3
1x Built-in 5.8G 40ch 25mw-200mw VTX
2x 1s 650mah Lipo battery
1x Propeller disassemble tool
1x Screwdriver
1x Happymodel Carry case
The Happymodel Moblite7 HDZero Whoop is a 75mm HD brushless whoop weighing just 29.5 grams. It features the HDZero Whoop Lite VTX and Nano Camera and a built-in SPI ELRS 2.4GHz or FrSky 2.4GHz receiver. With powerful EX1002 KV20000 motors and a Superbee F4 Lite flight controller, this should be a great performing high-definition whoop you can fly just about anywhere.
UART ELRS v3.0 ready
Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
The lightest 1S 75mm brushless whoop
Powerful and efficiency
The lightest 1S AIO 5IN1 F4 flight controller
1002 brushless motors
Low-profile Canopy design
HD Zero
Specifications
Wheelbase: 75mm
Size: 97x97x25mm
Weight: 19.5g (without battery)
Weight: 36g
Motor
Model: EX EX1002 20000KV
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.Len): Φ13.5mmx12.5mm
Weight(g): 2.5
No.of Cells(Lipo): 1S only
Flight Controller
SPI ELRS version Firmware target: CrazybeeF4SX1280
SPI FRSKY version Firmware target: CrazybeeF4FR
MCU: STM32F411CEU6 (100MHz, 512K FLASH)
Sensor: ICM20689 or ICM42688P or BMI270(SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/ELRSreceiver
Built-in 5V 1A BEC
Built-in voltage detection
Onboard 4in1 ESC
MCU Upgraded to EFM8BB21
Power Supply: 1S LiPo/LiPo HV
Current: 5A continuous, peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory Firmware: O_H_50_REV16_8.HEX
Default Protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version
SPI BUS receiver Frsky D8/D16 compatible
Compatible Non EU transmitter D8 model and EU-LBT(Frsky_x_lbt)
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m
Based on CC2500 RF module Compatible with Futaba S-FHSS , Redpine protocol
Onboard ELRS Receiver Version
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could bind with ELRS V2.0 firmware TX module
Onboard 5.8G 40CH 25-200mW VTX
Output Power: 25mw~200mw switchable
Frequency: 40CH
Input Voltage: 3.3V 5.5V
Current Consumption: 300mA (type)
Frequency: 5.8GHz 5bands 40 channels (include Race band)
Smart-audio Ready
HDZERO NANO LITE CAMERA SPECIFICATIONS:
Dimensions: 14x16x11 mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMOS sensor
Excellent low light performance
FOV:4:3: D:130° H:108° v:84°16:9:D:122° H:108° V:65°
Includes
1 x HappyModel BNF Moblite7 HDZERO 1S 75MM Brushless HD Whoop
1 x Moblite7 Spare Canopy
1 x Gemfan 1610 propeller Set (4cw+4ccw)
1 x Propeller disassemble tool
1 x Screwdriver
All batteries must be shipped by a ground shipping method.
Equipped with an ExpressLRS built-in SPI receiver, you'll never have to worry about range when whooping! This version of the Mobula6 also has another new feature: 0802 19000Kv motors! These motors are some of the lightest brushless whoop motors. Lighter whoops are easier to fly and super fast.
ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable.
This version comes pre-installed with ELRS 2.4GHz and ELRS V2.0!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 18.7g
Recommended Battery: 1S 300mAh
Propellor Size: 65mm
Antenna: Linear Dipole
HappyModel Crazy F4 FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CRAZYBEEF4DX
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (10sec)
ESC Firmware: BLheli_S
Stack Size: 25x25mm
Dimensions: 29x29mm
Weight: 5g
Motors
Stator Size: 0802
Kv: 19000
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x HappyModel BNF Mobula6 ELRS 65mm Brushless Whoop - ELRS 2.4GHz
4x 1S 300mAH Batteries
All product containing lithium batteries must be shipped by a ground shipping method. Please be aware Betaflight 4.3.1 firmware has a bug, Please do not flash version 4.3.1.
This is the V2 version of the Mobula 6 HD. This version features an ICM20689 Gyro as well as an OpenVTX 400mW VTX.
The Highly sought after Mobula6 now comes in HD! Record all your sessions in HD with the onboard RunCam split 3 Lite.We recommend RDQ 1S 300mAh LiPos for this whoop! Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
Extreme light 1S 65mm Brushless HD whoop only 27g
Come with Runcam Split3-lite 1080P HD DVR
Smooth and agile
Compatible for 1S Lipo/LIHV
Camera Angle adjustable
Specifications
Wheelbase: 65mm
Size: 80x80x40mm
Weight: 27g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Internal SPI DSM2/DSMX version(Compatible with SPEKTRUM DSM2/DSMX protocol radio transmitter)
External TBS CRSF NANO version(Compatible with TBS Transmitters)
Motors
Model: EX0802 19000KV
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Shaft Diameter: Φ1mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Weight(g): 1.7g
No.of Cells(Lipo): 1S only
Flight Controller
(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
(DSM2/X SPI RX version) CRAZYBEEX DXS DSM2/X version firmware target: CrazybeeF4DXS
(External TBS CRSF NANO RX version) CRAZYBEE F4 Lite Firmware target: CrazybeeF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G 400mW VTX
Built-in SPI Frsky/Flysky/DSMX receiver
Built-in 5V 1A BEC
Built-in voltage detection
ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band Smart audio ready
Runcam Split3 Lite
Model: RunCam Split3-Lite
Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps
Video File Format: MOV
Image Resolution:2 MP
TV Mode: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
Hole Distance of Installation: 25.5*25.5mm
PCB Size: 29*29mm
Lens Module Size: 14*14mm
Lens Specs: M9
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
Working Current: 450mA @5V
Includes
1x Happy Model BNF Mobula 6 HD 1S Whoop Quad - Choose Your RX
HappyModel has been an amazing company, bringing us FPV enthusiast quality whoops to fly. Take a look at HappyModels first ever whoop on a 85mm frame. It comes with X12 series flight controller, EX1103 KV11000 motors and Gemfan Hurricane 2023 tri-blade propellers, all together gives this whoop an amazing performance for an extremely smooth flight.
Choose between PNP (No RX) and BNF (ELRS SPI 2.4)
Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and OPENVTX
VTX Power up to 400mw
ELRS V2.0 (Default), can be flashed to ELRS V3.0
EX1103 KV110000 motors
CaddxFPV Ant FPV camera
Smooth and powerful
Compatible for 1S-2S Lipo/LIHV battery
3D Printed Camera Lens Protector
User Manuals
ELRS (SPI)
PNP (No RX)
Specifications
Brand Name: Happymodel
Motor: EX1103 KV11000
AIO: X12 5-IN-1 AIO flight controller
Camera: CaddxFPV Ant FPV camera
Prop: Genfan 2023-3 propellers
Weight: 42.7g
Input Voltage: 1-2S
Wheelbase: 85mm
Size: 120mmx120mmx50mm
Motor Specifications
Model: EX1103 KV11000
Configuration: 9N12P
Stator Diamter: 11mm
Stator Length: 3mm
Shaft Diameter: Φ1.5mm
Motor Dimension(Dia.xLen): Φ13.5mmx15.5mm
Weight(g): 3.8g
No.of Cells(Lipo): 1-2S
Propeller Specifications
Weight: 0.88g
Material: PC
Pitch: 2.3inch
Props Dia: 52.17mm
Center Thickness: 5mm
Center Hole Dia: 1.5mm
Flight Controller Specifications
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689 or ICM42688P(SPI connection)
Mount hole size: 25.5mm x 25.5mm
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
Built-in voltage detection
Built-in current sensor
Onboard 4in1 ESC
Power supply: 1-2S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Firmware target: Z_H_30
Default protocol: DSHOT300
Support Bluejay firmware
Onboard SPI ELRS 2.4GHz Specifications
Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could flash FC firmware to support ExpressLRS v3.0 TX module
PNP Version Specifications
Full UART1 for external Receiver
Support CRSF/GHOST/SBUS/IBUS/DSMX protocol
IR1 pad(invert RX1) used for SBUS input
Includes
1x HappyModel BNF Mobula8 1-2S Brushless Analog Whoop - Choose Your Receiver
1x Gemfan Hurricane 2023 tri-blade propellers (4CW+4CCW)
1x Screw Driver
1x Extra camera canopy
Experience powerful performance with the HappyModel BNF Mobula8 1-2S HD 85mm! This amazing quadcopter comes with an amazing DJI O3 Air Unit and Micro Cam, as well as Crazy F405 ELRS HD flight controller, EX1103 11000Kv motors, and Gemfan Hurricane 2023 tri-blade propellers for superior power performance. Get the perfect HD experience with the Mobula8!
Be sure to check out all our pre-built quads, and all our Happymodel products!
Specifications
Camera/VTX: DJI O3 Air Unit
Item Name: Mobula8 1-2S 85mm Micro FPV whoop drone
Size: 120mmx120mmx50mm
Brand Name: Happymodel
Wheelbase: 85mm
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Mount hole size: 25.5mm x 25.5mm
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
MOTORS
Motor Dimension(Dia.xLen):Φ13.5mmx15.5mm
Mode: EX1103 11000Kv
Shaft Diameter:Φ1.5mm
No.of Cells(Lipo):1-2S
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:3mm
Weight(g):3.8g
PROPELLERS
Center Hole Dia:1.5mm
Center Thickness:5mm
Props Dia:52.17mm
Weight:0.88g
Pitch:2.3inch
Material: PC
Includes
1x HappyModel BNF Mobula8 1-2S HD 85mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz
Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card.
Experience powerful performance with the HappyModel BNF Mobula8 1-2S HD 85mm! This amazing quadcopter comes with Crazy F405 ELRS HD flight controller, EX1103 11000Kv motors, and Gemfan Hurricane 2023 tri-blade propellers for superior power performance.
Be sure to check out all our pre-built quads, and all our Happymodel products!
Specifications
Item Name: Mobula8 1-2S 85mm Micro FPV whoop drone
Size: 120mmx120mmx50mm
Brand Name: Happymodel
Wheelbase: 85mm
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Mount hole size: 25.5mm x 25.5mm
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
MOTORS
Motor Dimension(Dia.xLen):Φ13.5mmx15.5mm
Mode: EX1103 11000Kv
Shaft Diameter:Φ1.5mm
No.of Cells(Lipo):1-2S
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:3mm
Weight(g):3.8g
PROPELLERS
Center Hole Dia:1.5mm
Center Thickness:5mm
Props Dia:52.17mm
Weight:0.88g
Pitch:2.3inch
Material: PC
Includes
1x HappyModel BNF Mobula8 1-2S HD 85mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz
HobbyZone Sport Cub S 2 BNF Basic with SAFE (Transmitter, Battery and Charger Not Included), HBZ44500, Blue & White
Introduction
The HobbyZone® Sport Cub S 2 is based on one of the all-time most popular trainer aircraft ever designed for learning to fly radio controlled (RC) airplanes—the legendary Sport Cub S. It's ultra-micro size makes it the ideal choice for a smaller trainer model that can be flown in yards, parks, soccer fields, football fields and other suitable spaces where larger models can't typically be flown successfully by first-time pilots. Exclusive SAFE® (Sensor Assisted Flight Envelope) technology helps to prevent overcontrol, loss of orientation and crashes so nearly everyone can learn to fly successfully. Beginner, Intermediate and Experienced modes allow you to choose the level of stability and control you need, or are ready to try, at the flip of a switch.
Features
Updated version of one of the best-selling and most popular trainer models available for learning to fly radio controlled (RC) airplanes – the Sport Cub S
100% factory-assembled and ready to fly right out of the box – no assembly required
Equipped with exclusive SAFE® technology that helps prevent crashes and makes it easy to learn how to fly
Beginner, Intermediate and Experienced flight modes you can easily change between at the flip of a switch
Panic Recovery mode activates at the push of a button to prevent loss of control and crashes
Ultra-micro size to fly in small parks, at sports fields or even indoors over a basketball court
Provides telemetry data to the controller/transmitter indicating flight battery voltage
Full 4-channel control for everything from training to aerobatic flight capability
Capable of aerobatic maneuvers including loops, rolls and upside down (inverted) flight
Powerful electric motor for easy operation and excellent performance
Lightweight yet durable construction perfect for first-time pilots
No FAA registration required (under the 250 gram weight limit)
Full line of replacement/spare parts plus accessories available
Optional float set (sold separately) for flying from water
Practice flying this aircraft in the RealFlight® simulator
Overview
Welcome to the exciting world of RC (Radio Controlled) flight! If you've ever dreamed of taking to the skies, Horizon Hobby has you covered. We are committed to engineering aircraft that you can learn to fly with successfully even if you've never flown RC before. Every HobbyZone® aircraft we offer features industry-leading design and technology developed by experts to keep you in control and learning at your own pace so you can turn your dreams of flight into a reality!
The HobbyZone® Sport Cub S 2 makes learning to fly RC airplanes in more places and smaller spaces easier than ever! Based on one of the most popular trainer aircraft ever designed for learning to fly radio controlled (RC) airplanes—the legendary Sport Cub S —it's ultra-micro size makes it the ideal choice for a smaller trainer model that can be flown in large yards, small parks, soccer fields, football fields and other suitable spaces where larger models can't typically be flown successfully by first-time pilots. Install the optional float set (EFLUA1190, sold separately) and you can add large pools and small ponds to the list of places you can fly! Exclusive SAFE® (Sensor Assisted Flight Envelope) technology helps to prevent overcontrol, loss of orientation and crashes so nearly everyone can learn to fly successfully. Beginner, Intermediate and Experienced modes allow you to choose the level of stability and control you need, or are ready to try, at the flip of a switch. Plus you can instantly return to stable flight using Panic Recovery in any flight mode. This makes the Sport Cub S 2 a natural evolution of the trainer many pilots learned to fly with because it includes all of the same great features, while also adding new telemetry capabilities that send flight battery voltage to the transmitter to make the pilot better aware of approximately how much "power" remains.
And the fun doesn't stop after you learn how to fly! It's lightweight yet durable airframe is equipped with a powerful electric motor that delivers long flight times and provides plenty of speed and power to perform aerobatic maneuvers including loops, rolls and even inverted (upside down) flight. That means the Sport Cub S 2 is a model even experienced pilots will appreciate and enjoy flying – and can also use to teach others to fly. The Bind-N-Fly® Basic version is the perfect choice for those pilots because it allows them to use their favorite Spektrum™ transmitter along with batteries and chargers they may already own. And the Ready-To-Fly version is perfect for first-time pilots because it includes a Spektrum™ controller/transmitter equipped with industry-leading DSMX® 2.4GHz technology, AA batteries for the transmitter, plus a rechargeable LiPo flight battery and USB charger. That means there's nothing extra to buy or provide! Best of all both versions arrive 100% factory-assembled and ready to go right out of the box – no assembly required!
Needed to Complete
6+ channel Spektrum™ DSMX®/DSM2® compatible transmitter
1S 3.7V 150–200mAh LiPo battery with Ultra-Micro connector
Compatible LiPo battery charger
What's in the Box?
(1) HobbyZone® Sport Cub S 2 with:
(1) Electric Motor (installed)
(2) Linear Servos (installed)
(1) Spektrum™ Receiver, ESC and (2) Servo Control Unit (installed)
(1) Product Manual
Video Overview
The next generation of ESCs from iFlight has arrived. Currently being used in their BNF quads such as the Chimera7 Pro BNF. These new 55 Amp BLHeli 32 Blitz 4-in-1 ESCs can handle even the most amp-hungry motors.
Check out all our 30x30 ESCs and all our iFlight gear selection!
Specifications
Input Voltage: 2-6S
Max. Continuous Current: 55A
Max. Burst Current: 65A
MCU: G071
BEC: No
Firmware: BLHeli32
Current Sensor: Yes
Target: IFLIGHT_BLITZ_G2
Mounting Dimensions: 30.5x30.5mm/Φ4mm
Dimensions: 35x42mm
Weight: 15.3g
Includes
1x iFlight Blitz E55 55A 2-6S 30x30 4in1 ESC
1x Wiring Set
Introducing the BOB57, a 6" cinematic long-range quad pre-installed with the all-powerful DJI O3 system for crystal clear image quality. This quad aims to best of 5" and 7", hence the name BOB57. This quad is DJI PNP, meaning it does not come with a receiver, meaning you need to install your receiver. However, if you have the DJI FPV Remote Controller 2, you can bind to the O3 Air Unit. This quad also comes with a GPS pre-installed, allowing all the marvelous features a GPS allows you. The BOB57 comes with XING2 2506 motors with a rated KV 1500, designed around 6S power.
The iFlight BOB57 is a long-range HD drone that was designed in collaboration with pilot & videographer Ellis van Jason. The team crafted this cinematic 6-inch drone that ensures agility and flight time while combining the advantages of both 5-inch and 7-inch drones for both cinematic and freestyle flights.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products
Features
Hybrid motor design optimized for that can be used with both bi-blade and tri-blade 6" propellers.
High-end GPS is used to minimize the risk of failure during proximity flights
Long backbone with enough space up to fit 3000mAh 6S batteries
Solid antenna mount for less oscillations when using long antennas
Gladiator shell protects from dust and water droplets
ESCs with built-in spike absorbers for more reliability
Built-in BEC to directly power a GoPro camera
9-minute flight time with 3000mAh 6S Lipo
Front-mounting XT-60
DJI O3 Air Unit
VERSATILE BODY
The Body is designed to carry small to large batteries for agile or long-range missions.
SMART XT60 AND USB-C PLUG
The XT60 plug is located in the front to gain more space. With the USB-C plug you can directly power your GoPro/Action Cams.
OPTIMIZED MOTOR AND PROPS
The Motor is designed for 6inch to give both great performance and efficiency. The prop is specifically optimized for this drone.
RELIABILITY
The BOB57 comes with a shell that protects against hits, droplets, and dust. It also has a high-quality GPS and components for more reliability, like a spike absorber & extra capacitor.
PRE-TUNED AND PRE-SETUP
Don't worry about tuning, iFlight did that for you already! A basic PID and Filter tuning were applied for a great flight experience!
Links
Ellis van Jason Tune Setup
Specifications
Product Name: BOB57 O3 6S HD BNF
FC: BLITZ F722
ESC: BLITZ E55 55A 4-IN-1 ESC
Video Transmission: DJI O3 Air Unit
Frame: 280mm wheelbase
Motor: XING2 2506 motors
Prop: GEMFAN 6032-3 propellers
Takeoff Weight: Approx. 580 g
Dimensions (L×W×H)：226×166×34 mm
Max Speed: 180 Km/h (Manual Mode)
Maximum Takeoff Altitude: 7000 m
Max Hover Time: Approx. 8 mins (With 6S 1400 no load.)
Max Wind Speed Resistance: Level 7
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Antennas: 2 Antenna
GNSS: GPS+SBAS+Galileo+QZSS+Glonass
Video Transmission
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4 grams（headband included）
Dimensions (L×W×H): L32.5x W30.5xH 14.5mm
Communication Bandwidth： Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Includes
1x BOB57 6S HD BNF
2x Antennas
2x Battery pads
2x Prop(Pairs)
All batteries must be shipped by a ground shipping method.
Introducing iFlight's Defender 25, a sub-250 drone featuring the DJI O3 Air Unit. At 249g weight, Defender 25 doesn't require registration in most countries. The compact and lightweight design also make it easy to carry and store. It will be your best travel buddy to redefine your FPV adventure. The built-in 2.5-inch propeller guards were designed to fly boldly. You’ll experience a completely new creative freedom to fly whenever and wherever. The durable injection molded frame not only prevents damage to your motors or propellers but also protects the environment from small flight errors.
Equipped with the latest tech from DJI, the O3 Air Unit HD transmission system, the Defender 25 supports 4K video and shoots up to 155° super-wide FOV footage for stunning visuals. In addition, D-Cinelike color mode provides more creative freedom for color grading, allowing you to edit and adjust your footage.
They’ve also added a special vibration-damped camera mount to keep your raw footage as smooth as possible, as well as ensure good Gyro Data for the built-in or in-post camera stabilization.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Features
Optimized Landing Gear for Take-Off in Complex Environments
Built-in High-Performance video and Receiver Antennas
4K Stabilized Video with 155° Ultra-Wide Angle
Crash-Protected Quick-Release Battery
Countless Easy-to-Use Features
Ultralight and Free to Fly
Small and Mighty
Specifications
Defender 25
Product Name: Defender 25 4S HD
Flight Electronics: BLITZ D25 F7 AIO
Video Transmission: DJI O3 Air Unit
Frame: 112±2mm
Motor: Defender25 1404
Prop: Defender25 2525 props (2.5-inch)
Weight of the Aircraft: 180g
Takeoff Weight incl. 550mAh battery: ≤249g
Dimensions (L×W×H)：158x155x69mm
Max Ascent Speed: 6 m/s (Normal Mode, Sport Mode)
Max Descent Speed: 6 m/s (Normal Mode, Sport Mode)
Max Speed: 100Km/H (Manual Mode)
Maximum Takeoff Altitude: 200 m
Max Hover Time: Approx. 6 mins (with 550mAh battery), 10mins (with 900mAh battery)
Max Flight Distance: 2-3 km
Max Wind Speed Resistance: 80 Km/H (Level 5)
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Transmission Power (EIRP): FCC: < 33 dBm / CE: < 14 dBm / SRRC: < 30 dBm
Antennas: Dual Antennas
GNSS: N/A
Video Transmission
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4grams
Dimensions (L×W×H): L16.7×W103.9×H 81.3mm
Screen Size (single screen): 0.49-inch
Resolution (single screen): 1920×1080
Refresh Rate: Up to 100 Hz
Interpupillary Distance Range: 56-72 mm
Diopter Adjustment Range: -8.0 D to +2.0 D
FOV (single screen): 51°
Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz
Transmission Power (EIRP):
2.4 GHz: < 30 dBm (FCC), < 20 dBm (CE/SRRC/KC)
5.8 GHz [4]: < 30 dBm (FCC), < 23 dBm (SRRC), < 14 dBm (CE/KC)
Max Video Transmission Bitrate: 50 Mbps
Operating Temperature Range: 0° to 40° C (32° to 104° F)
Power Input: 7-9 V (1.5 A)
Recommended (Not Included)
iFlight Defender 25 Battery - 900mAh
Includes
1x iFlight BNF Defender 25 HD 4S 2.5" Cinewhoop w/ DJI O3 Air Unit and DJI Camera (Pre-Built, Tuned, and Tested)
1x Defender 25 550mAh Battery
1x Charging Adapter Board
2x Defender 25 2525 Props (pairs)
The iFlight Nazgul5 V3 6S 5" Freestyle Analog Quad is here! It includes the RaceCam R1 FPV Camera and Nazgul 5" tri-blade props, XING-E Pro 2207 motors, BLITZ F7 Flight Controller, BLITZ 1000mW+ VTX, and the BLITZ E45S 2-6S 45A BLHeli32 4-in-1 ESC. Boasting CNC aluminum camera mount with vibration-reduction silicone for increased protection. Great for freestyling and long-distance shots with your GoPro camera! The Nazgul5 Freestyle quad is a go-to gold standard for freestyle BNFs of great value made by the great people at iFlight. The Nazgul5 V3 is a 5" freestyle frame is made of super stiff carbon for minimal resonance.
+ High-quality parts+ Sturdy frame structure+ Generous mounting space+ Optimized for O3 Air Unit+ GoPro camera mount included
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Features
XING-E Pro 2207 motors and NAZGUL F5 props
5" version also fits 5.1" style propellers
Fits both 30.5x30.5 and 20x20 stacks
5mm arm design for more durability
Popular True-X configuration
LED illuminated logo
TPU crash-guards
Easy-Swap arms
Specifications
Product Name：Nazgul5 V3 6S Analog
FC: BLITZ F722 FC
ESC: BLITZ E45S 45A 4-IN-1 ESC
Video Transmission: BLITZ 1mW+ VTX
Frame: 245 ±2 mm wheelbase
Motor: XING-E Pro 2207 motors
Prop: Nazgul 5 inch propellers
Takeoff Weight: Approx. 435g / 660±10g (With 6S 1400mAh Battery)
Dimensions (L×W×H): 173×173×34±2 mm
Diagonal Distance: 245mm
Max Speed: 190 Km/h (Manual Mode)
Maximum Takeoff Altitude: 3200 m
Max Hover Time: Approx. 7.5 mins (No Load with 6S 1400mAh Battery)
Max Flight Distance: 5 km
Max Wind Speed Resistance: Level 7
Operating Temperature Range：-10° to 40° C (14° to 104° F)
Antennas: Single Antenna
Video Transmission System
Product Name: BLITZ Whoop 1mW+ VTX
Input voltage: 7V～34V
Interface: MMCX
Power levels: PIT/25mW/400mW/800mW/1600mW
Channels: 40 (including Raceband)
Mounting pattern: 30.5x30.5mm/Φ3
Lightweight: 18.9g (excluding antenna)
VTX telemetry: IRC Tramp
Betaflight IRC Tramp Configuration: Please download the attached VTX table for Betaflight!
RC Tramp VTX table values: 25mW/400mW/800mW/1600mW
Includes
1x Nazgul5 V3 6S Analog BNF
1x Antennas
2x Battery pads
2x Nazgul F5 Prop(Pairs)
The Nazgul5 HD V3 is loaded with lots of power and performance; it comes with the XING-E Pro 2207 6S motors, BLITZ F722 FC, and BLITZ E45S 45A 4-in-1 ESC, which makes this quad a must-have! Now with the DJI O3 Air Unit! The Nazgul V3 is one of the best freestyle frames for its value. The Nazgul5 V3 HD has been pre-tuned and set up with everything you need, all you need to do is bind-and-fly. The Nazgul5 V3 is a 5" freestyle frame made of super stiff carbon for minimal resonance.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Features
XING-E Pro 2207 motors and NAZGUL F5 props
5" version also fits 5.1" style propellers
Fits both 30.5x30.5 and 20x20 stacks
5mm arm design for more durability
Popular True-X configuration
LED illuminated logo
TPU crash-guards
Easy-Swap arms
Specifications
Operating Temperature Range：-10° to 40° C (14° to 104° F)
Max Wind Speed Resistance: 130 Km/H (Level 4)
Receiver: DJI BNF, ELRS
Dimensions (L×W×H): 180×180×80 mm
Max Speed: 130 Km/h (Manual Mode)
Video Transmission: DJI O3 Air Unit
Maximum Takeoff Altitude: 5000 m
Product Name：Nazgul5 V3 6S HD
ESC: BLITZ E45S 45A 4-IN-1 ESC
Max Hover Time: Approx. 8 mins
Motor: XING-E Pro 2207 motors
Takeoff Weight: Approx. 620 g
Prop: Nazgul 5 inch propellers
Diagonal Distance: 245mm
Frame: 255mm wheelbase
Max Flight Distance: 5 km
Antennas: 2 Antenna
FC: BLITZ F722
GNSS: N/A
Video Transmission
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4 grams（headband included）
Dimensions (L×W×H): L32.5x W30.5xH 14.5mm
Communication Bandwidth： Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Includes
1x iFlight BNF Nazgul5 V3 HD 6S 5" Freestyle Quad w/ DJI O3 Air Unit & Micro Cam - Choose Receiver
2x Nazgul 5 inch propellers (Set of 4)
2x Battery Pad
2x Antenna
After our very popular 3-inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.
Our all-new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here.
ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all-new 2205 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to its 3inch predecessor which gives a lot more room for a lot more fun. Our GPS-measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch-outs or light freestyle moves.
A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Note: Battery, GoPro, and GoPro mount are NOT included.
Check out our other pre-built quads, as well as the rest of our iFlight selection!
Features
High-performance True-AIO Board Beast Whoop F7 AIO 55A v2.0 to save weight and space
T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
Low Resonance frame construction (Less Jello, more Cinematic footage)
Pre-tuned with smooth freestyle settings
Butter smooth 2205 3200KV (4S)
ProTek35 Prop Guards V2.0
No Props or frame in view!
Pre-Tuned & Pre-Setup:
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning were applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, and activate Acro-Mode"
Specifications
Beast F7 V2 AIO FC
MCU: BGA-STM32F745
Gyro: BMI270
Blackbox: 8Mb Onboard Flash
BEC output: 5V 2.5A
Barometer: BMP280
Connector: Micro-USB
OSD: AT7456E
FC Firmware：IFLIGHT_F745_AIO_V2
Mounting pattern: 25.5x25.5mm φ3mm
Dimensions: 32.5x32.5mm
Weight: 8.5g
F7 55A 2-6S ESC
Current Sensor: Yes
Input: 2-6S LIPO
Current scale: 200
Constant: 55A
BLHeli: BLHeli-S
Telemetry: no
ESC Firmware: BlheliS G-H-30
Mounting pattern: 25.5x25.5mm/Φ3mm
Dimensions: 32.5x32.5mm
SucceX Mini Force 5.8GHz 600mW VTX
Power: PIT/25/200/400mW/600mW
Antenna interface: MMCX
VTX protocol: IRC Tramp
Output 40 channels.
Size: 29x29mm
Mounting pattern: 20x20Φ3/25x25 mmΦ2
Weight: 4g
Includes
1x ProTek35 Frame
2x Albatross RHCP RP-SMA 5.8g antenna
1x TPU Antenna holder
2x Nazgul 3535 propeller (Set of 4 - Color May Vary)
1x iFlight Lipo Strap 15x150mm (Color May Vary)
1x iFlight Lipo Strap 15x250mm (Color May Vary)
1x GoPro TPU bottom stand black (GoPro Protector not included)
NewBeeDrone Cockroach Brushless Extreme-Durable Frame 75mm
Design Intent:
For this frame, we worked to develop a platform that would neither fall below expectations nor limit the creativity of the FPV community. The Cockroach 75mm is lightweight and versatile. We improved durability and worked to deliver a vibrational signature that made tuning easier so you can get the most performance out of NewBeeDrone flight controllers and motors. Every gram of frame material was either added or taken away to ensure that what was left was there for a reason.
Lightweight and Durable:
We found a more forgiving and resilient material that doesn't sacrifice in weight or stiffness. Struts and other key support components have been redesigned to distribute and dissipate stress from crashes and falls with a total weight of 6.98g.
Traditional Looks and Geometry:
This 75mm Cockroach frame has adaptable FC locations and a multitude of additional mounting points across the frame. We delivered a frame that has 2 board locations with 1x1inch or 25.4x25.4mm hole spacing. One mounting location on the top and another below to mount an additional board like a DVR or a 4K HD recording board. The 2-board mounting adaptability allows for the possibility for a pusher-style flying configuration to be used as well.
1mm Carbon Fiber Plate
A 1mm carbon plate is included for increased durability insurance. Though the frame can be flown without it, the carbon allows for additional adaptability and opens the frame's use for exciting opportunities in a pusher-style configuration. Flip the frame over and install it. Please be aware, the motor screws that come with the 75mm frame are expected to be used with carbon fiber. If you choose to use them without the carbon fiber plate – the screws may contact the motor PCB.
This 75mm frame does not come with just one limiting battery mounting solution. We understand that depending on the utility and flying style, many people want to run one or two 300mah Nitro Nector Golds in the traditional battery position or in a ‘toilet-tank’ position. We have developed several printable, TPU battery mount solutions to use with the frame and are always open to your suggestions.
Included are 4 3D printed mounting tabs. Use 2 to mount one Nitro Nectar Gold 1s Battery and all 4 to mount 2x Nitro Nectar Gold 1s Batteries. When using 2 batteries, you can choose to run them in either series (2s) to increase voltage or parallel (1s) to increase capacity.
Easy and Inexpensive.
None of this is any good if it's super difficult to use and/or super expensive. So we made sure we set out to make something affordable. Key tolerances have also been fine-tuned to make installation and removal much easier.
Any of our other whoop BNFs can be directly dropped in into the 75mm frame.
Check out the rest of our micro frames and the rest of our NewBeeDrone products!
Specifications
Motor Mount Pattern: Tri 6mm
Weight: 3.71g
Includes
1x NewBeeDrone 75mm Cockroach Brushless Extreme Durable Whoop Frame
Introducing the smallest HD whoop with the DJI O3 currently on the market. This amazing 75mm quadcopter comes with the elite DJI O3 Air Unit and O3 Micro Cam, and the new BeeBrain BLV4 HD F7 AIO flight controller. Achieve sharper HD capture with amazing quality with O3 Air Unit. Boasting powerful 0804 12000kv dual ball bearings motors, despite its small size, this thing will rip!
Check out our other pre-built quads, as well as the rest of our NewBeeDrone selection.
Explore and film spaces you never could before in HD! A must-have tool for professionals and hobbyists specializing in indoor space.
The only HD Micro whoop board with F7 processor. Dual-bearing motors allow less friction in spinning while 3-blade Azi propellors were developed with engineering theory for optimal air-grab and stability. We master-tuned this drone to have the smoovest flight and absolutely no jello in any videos.
We found the best ratio between the size of drone and its weight distribution. Without DJI O3, the drone can fly up to 8 minutes. Up to 3 minutes with DJI O3 and battery. Choose between 3D printed battery mounts or strap.
We ensure that you get the best material and components that are available so you can rely on the drone without troubleshooting or breaking. All parts are available separately as replacements. Additional flexibility with SLS Nylon prints allow cameras to be changed or updated if needed.
Assembly or tuning not required. Save time and energy so you can focus on your footage. Drone comes with built-in ExpressLRS and ready to pair. Built-in blackbox records data for tuning. Configure to DJI PNP on Betaflight if needed. Don't be afraid of messing up on customization. Reset to factory default (with our tunes and dump files) in one click if something is not right.
Specifications
Drone Size: 75mm
Flight Controller: BeeBrain BLV4 HD F7 Flight Controller ExpressLRS (ELRS) 2.4G
Frame: Cockroach75 Brushless Frame
Motors: Flow 0804 12000kv Double Ball Bearing Brushless Motor
Propellesr: Azi (Tri-Blade) Micro Propellers 40mm - 1.0mm Shaft
HD VTX & Camera: DJI O3 Air Unit
Canopy: NewBeeDrone Acrobee75 HD O3 Canopy
Total Weight without battery: 70.19g
Total Weight with battery: 98.24g
BeeBrain BLV4 HD F7 Flight Controller ELRS2.4G Specifications:
MCU: STM32F745
ESC Firmware: S-H-40 - Bluejay, 0.19.2, 48kHz.
ESC Specifications: 4 channel 12A ESC
ESC Connector: JST-1.0 3Pin
Weight: 6.6 grams (including antennas and battery connector)
Size: Outer dimensions 29 x 29 x 7.6 mm
Holes: 25.5 x 25.5 mm
Battery input: 2S
Connector: XT30
Internal Blackbox: 16MB
Gyro: BMI270
UART1: SBUS on DJI Connector (RX only)
UART2: TX & RX for internal ExpressLRS 3.0 receiver
UART3: TX & RX for DJI MSP+Displayport
Flight time with Tattu 450mAh 2S battery is 3:00min (at 7v)
Firmware:
BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune
Includes
1x NewBeeDrone BNF AcroBee75 BLV4 2S HD 75mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz
We heard you asking for it, so we got it, the HummingBird F4 V2 Flight Controller, these AIO whoop style FCs are meant as replacements and upgrades for whoops/toothpick builds. This board is also the direct replacement board for NewBeeDrone BNF Hummingbird F4 V2.1 1S Brushless Whoop.
Check out all of our AIO Flight Controllers and our NewBeeDrone products for sale at RaceDayQuads!
Specifications
STM32F411 MCU (for the main controller (Preloaded with Betaflight)
Support 1S battery ONLY
Current sensor onboard
ESC-12A Per Motor Channel BB21 MCU
BlHeliS Support DShot(150 300 600) Multishot
Gyro- BMI270
Onboard Sideway RGB LED controlled by Betaflight
Support BeeSign signal compatible with NBD VTX-Camera System
Onboard Diversity SPI SX1280 Receiver(EXPRESSLRS)
MotorPlug JST1.0
NBD OSD(Betaflight OSD Compatible)
5V 2A Power support for external VTX Camera Or Receiver.
Includes
1x BeeBrain BLV4 Flight Controller
4x Grommet
1x Mounting Kit
1x Receiver Antennas
1x VTX Antenna
Wiring Diagram
All batteries must be shipped by a ground shipping method.
NBD is excited to introduce the Nitro Nectar Gold Series HV Lipo Battery Series! They use a different battery packaging technology that provides a better discharging rate for those who like to push the limit! They tested these batteries with their powerhouse 1S craft, the AcroBee BeeBrain BL BNF and they are built to keep up with the demand of raw thrust! After 3 months testing, NewBeeDrone is ready to bring them to the market for whoop pilots across the world!
Lightweight, durable and plenty of power to bring home the Gold!
Check out our 1S battery selection, and all our NewBeeDrone gear!
NOTE: These packs are designed to deliver a major amount of power! With the discharge rate that gives these packs such power, you will feel pack sag much later than normal packs. We suggest setting the low voltage reading to 3.5v and bringing it in to land at 3.3v. You are able to fly below 3.3v but that may result in battery degradation. You will need a high voltage capable charger, such as our brand new Nectar Injector portable USB powered charger.
Specifications
Cell count: 1
Nominal voltage: 3.8V
Max voltage: 4.35V
Capacity: 300mah
Continuous discharge rating: 40C
Max discharge rating: 80C
Dimensions: 62mm x 10.5mm x 6.5mm
Weight: 8.10g (+/-1%)
Plug: PH 2.0 or GNB27
Wire Length: PH2.0 None, GNB27 50mm
Watt hours: 1.14 Wh
Includes
1x Nitro Nectar Gold 3.8V 1S 300mAh 30/60C LiHV Whoop/Micro Battery
Introduction
The Truman Senate War Investigating Committee called the North American Aviation P-51 Mustang “the most aerodynamically perfect pursuit plane in existence.” During WWII, it blasted trains, ships, and enemy installations throughout Western Europe. The “D” variant, outfitted with the legendary Merlin engine, gave the U.S. Army Air Forces a high-altitude, long-range fighter capable of escorting heavy bomber formations the entire way to Berlin and back. The E-flite® P-51D Mustang 1.5m also goes the distance — to reproduce the famous fighter with exceptional detail, handling, performance and presence. It’s packed with Extra Scale details and functional features including LED lights, sequenced main and tailwheel gear doors, flaps and much more, and is also equipped with a Spektrum™ Avian™ Smart ESC to deliver an unmatched warbird flying experience.
Features
The most detailed, best handling and highest performance large-scale P-51D Mustang model yet
Scale replica of the iconic aircraft flown by the U.S. and other allied forces during World War II
Extra Scale details including removable drop tanks, molded-in panel lines, guns and much more
Functional Extra Scale features including LED navigation lights, sequenced main gear and tailwheel doors, flaps and more
Factory-installed, high-power 6S-compatible brushless motor with large diameter 4-blade prop
Fits 6S batteries from 3200-7000+mAh to deliver level flight top speeds up to 80+ MPH and unlimited vertical performance
100-amp Spektrum™ Avian™ Smart ESC provides real-time battery voltage, capacity used and other data via compatible receivers and transmitters
Spektrum AR637TA receiver with full-range telemetry and industry-leading DSMX® technology
Easy to fly with innovative and optional-use SAFE® Select flight envelope protection
The unmatched stability and locked-in feel of exclusive AS3X® technology
Nine factory-installed servos with precise ball-link equipped linkages
Ball-bearing equipped wheels with diamond tread pattern tires for added scale appearance
Retractable tailwheel plus main gear with scale shock-absorbing struts for operation from a variety of surfaces including grass
Unique 3-piece wing includes center section with main gear plus outer panels that snap into place securely without fasteners
No glue required for assembly and can be ready to fly in less time than it takes to charge a battery
Large top hatch with molded in stop for added security of the quick-release battery tray
Factory-applied “Lou IV” painted trim scheme offers excellent visibility
Durable EPO airframe with carbon fiber and wood reinforcement
Overview
The P-51D Mustang 1.5m is the largest, most detailed and best performing replica of the legendary fighter from E-flite® yet! Along with an accurate outline, it also features an abundance of Extra Scale details including molded in panel lines and hatches, guns and removable drop tanks, plus a striking factory-applied “Lou IV” finish. Functional Extra Scale features include LED navigation lights, sequenced main and tailwheel gear doors, flaps and more. The shock-absorbing struts feature ball-bearing equipped wheels with diamond tread tires for added scale appearance and make it possible to fly from a variety of surfaces including grass, and reliable electric retracts operate the main gear and tailwheel. And at the heart of it all is a factory-installed brushless motor that’s compatible with 6S LiPo power—simply drop in a 6S 3200-7000mAh battery to achieve level flight speeds in excess of 80+ MPH and unlimited vertical performance! Both versions include a 100-amp Spektrum™ Avian™ Smart ESC, and the BNF® Basic version is also equipped with an AR637TA receiver that offers full-range telemetry including real-time battery voltage, current, temperature and more to compatible transmitters, plus the advantages of exclusive AS3X® and SAFE® Select technologies to make this one of the easiest to fly Mustangs ever. The unique 3-piece wing design makes transport and storage as convenient as possible because the center section includes the main gear and the outer panels simply snap into place securely without requiring fasteners. It’s also quick and easy to assemble because the factory-finished EPO airframe bolts together—no glue required—in less time than it takes to charge a battery. And it all adds up to deliver a warbird flying experience unlike any other with the mightiest Mustang yet!
Needed to Complete
Full-range 6-7+ channel Spektrum™ DSMX®/DSM2® compatible transmitter
6S 22.2V 3200–7000+mAh LiPo with EC5™ or IC5™ connector
Compatible LiPo charger
What's in the Box?
(1) E-flite P-51D Mustang 1.5m with:
(1) 100A Spektrum™ Avian™ Smart Brushless ESC (installed)
(1) Brushless Motor (installed)
(9) Servos (installed)
(1) Spektrum AR637TA 6-Channel Receiver (installed)
(1) Product Manual
This is a programming cable for the FrSky R-XSR receiver. This is a great tool if you have lost your cable, or if you purchased a BNF quad that did not come with this. Plugging this into your radio and receiver will allow you to change the firmware on your R-CSR receiver.
Check out the rest of our RC transmitter accesories.
Specifications
Length: 250mm
Weight: 1.6g
Includes
1x R-XSR to Servo Lead Programming Cable
The Sub250 Whoopfly16 BNF is an ultra-light analog 1S mini Whoop designed for a smooth indoor flying experience. It features an inverted pusher FPV drone layout, a one-piece injection-molded protective ring frame, and a short wheelbase to provide maximum safety and protection. Powered by a popular 1002 motor, this reliable drone delivers a strong and effortless user experience. Whoopfly16 can adapt to mainstream 1S image transmission (analog / HD Zero / AVATAR).. The analog video transmission will be equipped with an Ant eco lens from Caddx, and the elevation angle of the lens can be adjusted upwards by 30 degrees. With the latest 1s 530mah battery, the battery life can reach 4 minutes and 30 seconds.
Make sure to check out all of our Analog BNF quads as well as the rest of our Sub250 selection!
Features
Inverted whoop FPV drone makes the paddle and motor more efficient.
With the new 1S 530mah LiHV battery
Highly integrated flight control, integrated flight control, ESC, remote control receiver, and video transmission.
One-piece injection molded protective ring frame, higher strength, and less deformation of the frame during aggressive flight.
The protection of the circle is enhanced, and novices and experienced pilots both are safe.
There are many options for image transmission, you can choose HD Zero /AVATAR and analog image transmission
Use 1002 21000kv motor, abundant power "always ready to overtake"
Indoor flight is safer with a small wheelbase and a protective ring, and it is handier to fly with a reasonable combination.
Suitable for beginner outdoor advanced racing practice
Specification
Analog Version
Product name: Whoopfly16
Frame: WF16
Wheelbase size: 75mm
Flight control system: Redfox A1
MCU: STMF411
IMU: ICM42688-P
OSD: BetaFlight OSD w/AT7456E chip
ESC: Redfox A1 4IN1 5A ESC
VTX: VTX 5.8G 200mW
Lens: Caddx Ant eco
Propeller: Gemfan 1608-3
Antenna: 5.8g copper tube antenna 70mm
weight: 37.7g
Receiver: ELRS (SPI)
Includes
1x Sub250 Whoopfly16 BNF 1.6" Analog Ultra-Light 1S Whoop - ELRS 2.4GHz (SPI)
4x M1.4 cross screws
1x Blue frame protection cotton
1x Red frame protective cotton
1x L-shaped inner hexagon screw blade
1x Cross screw blade
2x 3M double-sided tape
4x 1608-3 propellers
The Sub250 Whoopfly16 BNF is an ultra-light 1S mini Whoop designed for a smooth indoor flying experience. It features an inverted pusher FPV drone layout, a one-piece injection-molded protective ring frame, and a short wheelbase to provide maximum safety and protection. Powered by a popular 1002 motor, this reliable drone delivers a strong and effortless user experience. Whoopfly16 can adapt to mainstream 1S image transmission (analog / HD Zero / AVATAR). The analog video transmission will be equipped with an Ant eco lens from Caddx, and the elevation angle of the lens can be adjusted upwards by 30 degrees. With the latest 1s 530mah battery, the battery life can reach 4 minutes and 30 seconds.
Make sure to check out all of our HDzero BNF quads as well as the rest of our Sub250 selection!
Features
Inverted whoop FPV drone makes the paddle and motor more efficient.
With the new 1S 530mah LiHV battery
Highly integrated flight control, integrated flight control, ESC, remote control receiver, and video transmission.
One-piece injection molded protective ring frame, higher strength, and less deformation of the frame during aggressive flight.
The protection of the circle is enhanced, and novices and experienced pilots both are safe.
There are many options for image transmission, you can choose HD Zero /AVATAR and analog image transmission
Use 1002 21000kv motor, abundant power "always ready to overtake"
Indoor flight is safer with a small wheelbase and a protective ring, and it is handier to fly with a reasonable combination.
Suitable for beginner outdoor advanced racing practice
Specification
HD Zero Version
Product name: Whoopfly16
Frame: WF16
Wheelbase size: 75mm
Flight control system: Redfox A1
MCU: STMF411
IMU: ICM42688-P
OSD: BetaFlight OSD w/AT7456E chip
ESC: Redfox A1 4IN1 5A ESC
VTX: Hd Zero whoop lite
Lens: Hd Zero nano lite camera
Propeller: Gemfan 1608-3
Antenna: 5.8g copper tube antenna 70mm
weight: 39.2g
Receiver: ELRS (SPI)
Includes
1x Sub250 Whoopfly16 BNF 1.6" HD Ultra-Light HDzero 1S Whoop - ELRS 2.4GHz (SPI)
4x M1.4 cross screws
1x Blue frame protection cotton
1x Red frame protective cotton
1x L-shaped inner hexagon screw blade
1x Cross screw blade
2x 3M double-sided tape
4x 1608-3 propellers
