CLRacing is well trusted in the industry and the CLRacing F7 V2.2 45A 2-6S 30x30 Stack/Combo will show you exactly why. Durable, feature rich, and easy to solder to. Check out the specs below!
This F7 FC and 45A 4in1 ESC are available separately as well!
Choose either dual or single gyro version.
Check out all our 30x30 Stacks and Combos and our full range of CLRacing products!
Specifications
FC
Input Voltage: 2-8S
MCU: STM32F722RET6216MHz
IMU: Choose Dual ICM20602 or Single MPU6000
OSD: Yes
BlackBox: 32MB
UARTS: 6
ESC Connections: 6
Reverse Polarity Protection: Yes
Camera Control: Yes
BEC: 5V/1.5A, 3.3V/250mA
Buzzer Pads: Yes
LED Pads: Yes
Mounting Dimensions: 30x30
ESC
Input Voltage: 2-6S
Max. Continuous Current: 45A
Max. Burst Current: 55A
Firmware: BLHeli_32
Support: Dshot300-1200/MultiShot/OneShot/ProShot/PMW
Current Sensor: Yes
Current Sensor Scale: 250
Dimensions 43.5mm x 46.5mm
Mounting Dimesions: 30.5x30.5mm Φ4mm
Weight: 13.5g
Includes
1x CLRacing F7 V2.2 30x30 Flight Controller
1x CLRacing 45A V2 32bit 30x30 4in1 ESC
1x Wiring & Accessory Kit
NOTE: PICTURES ARE FROM THE OLDER VERSION. UPDATED PICTURES INCOMING
Similar to the RaceWire, this product from CLRacing offers protection of your motor's wires while simultaneously making your quad look fantastic with 6 bright LEDs. Available in White, Red, Green, Purple, Yellow and Blue, the CLRacing LED Race Wire has colors to suit any quad! Note, the listing is for 4pcs.
CLRacing Race LEDs Specs:
Weight: 1.1g
LED Quantity: 6
Size: 9x35x1.6mm
Lipo Input: 3-6S
Color: Red, White, Blue, Green
Unit Quantity: 4pc
All batteries must be shipped by a ground shipping method.
The CNHL Black Series LiPo is 25g lighter than its predecessor, the G+ Series. This is an extremely high-powered, high-density pack for pilots who need to squeeze every last drop of performance out of their rig. We also carry the 6S 1300 Black!
Check out our selection of 6S batteries, and all our CNHL products!
Specifications
Nominal Voltage: 22.2V
Cells: 6
Capacity: 1100mAh
Discharge Rate (Cont./Burst): 100C/200C
Max Charge Rate: 5C
Dimensions: 39.5x35x75mm
Discharge Lead: XT60
Balance lead JST-XH
Weight: 211g
Includes
1x CNHL Black Series 22.2V 6S 1100mAh 100C LiPo Battery - XT60
All batteries must be shipped by a ground shipping method.
The CNHL Black Series LiPo is 25g lighter than its predecessor, the G+ Series. This is an extremely high-powered, high-density pack for pilots who need to squeeze every last drop of performance out of their rig.
Check out our selection of 6S batteries, and all our CNHL products!
Specifications
Nominal Voltage: 22.2V
Cells: 6
Capacity: 1300mAh
Discharge Rate (Cont./Burst): 100C/200C
Max Charge Rate: 5C
Dimensions: 76x47x35mm
Discharge Lead: XT60, 90mm
Balance lead JST-XH, 45mm
Weight: 230g
Includes
1x CNHL Black Series 22.2V 6S 1300mAh 100C LiPo Battery - XT60
All batteries must be shipped by a ground shipping method.
The CNHL Black Series LiPo is 25g lighter than its predecessor, the G+ Series. This is an extremely high-powered, high-density pack for pilots who need to squeeze every last drop of performance out of their rig.
Check out our selection of 6S batteries, and all our CNHL products!
Specifications
Capacity: 1500mAh
Voltage: 22.2V / 6-Cell / 6S1P
Discharge Rate: 100C Continual / 200C Burst
Charge Rate: 5C Max
Size: 53x33x75mm
Weight: 254g (Including wire and connector)
Output Connector: XT60
Balance Connector: JST / XH
Includes
1x CNHL Black Series 22.2V 6S 1500mAh 100C LiPo Battery - XT60
All batteries must be shipped by a ground shipping method.
The CNHL Black Series LiPo is lighter than its predecessor, the G+ Series. This is an extremely high-powered, high-density pack for pilots who need to squeeze every last drop of performance out of their rig.
Check out our selection of 6S batteries, and all our CNHL products!
Specifications
Nominal Voltage: 22.2V
Cells: 6
Capacity: 2000mAh
Discharge Rate: 100C
Dimensions: 71x39x78mm
Discharge Lead: XT60
Balance Lead: JST-XH
Weight: 339g
Includes
1x CNHL Black Series 22.2V 6S 2000mAh 100C LiPo Battery - XT60
All batteries must be shipped by a ground shipping method.
The perfect pack may be a pie in the sky but this pack is pretty darn close.
Check out our selection of 6S batteries, and all our CNHL products!
Specifications
Nominal Voltage: 22.2V
Cells: 6
Capacity: 1200mAh
Discharge Rate (Cont./Burst): 100C/200C
Max Charge Rate: 5C
Dimensions: 48x35x75mm
Discharge Lead: XT60
Balance lead JST-XH
Weight: 210g
Includes
1x CNHL Speedy Pizza Drones 22.2V 6S 1200mAh 100C LiPo Battery - XT60
Check out this co-brand motor from CNHL, Axisflying & SpeedyPizzaDrones, with the saying of three heads being better than one, these three companies graced us with bringing you this amazing motor before you now. Motors likes these focus on premium performance and reliability. The DIAVOLA Series! Fresh from the labs, this is the final product of months of designing, testing and finishing in order to deliver the most powerful motor possible while keeping a great ratio on reliability and price.
DIAVOLA 2207 comes in 2020Kv if preferred.
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 4~6S
Kv Rating: 1960Kv
Stator Size: 22x7mm
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 5mm
Max. Power: 901.3W
Internal Resistance: 60mΩ
Peak Current: 40.6A
Motor Dimensions: ɸ26.9x32.8mm
Weight (Excl. Cable): 30.5g
Includes
1x CNHL Speedy Pizza Drones Axis Flying Diavola 2207 1960Kv Brushless Motors
Check out this co-brand motor from CNHL, Axis Flying & SpeedyPizzaDrones, with the saying of three heads being better than one, these three companies graced us with bringing you this amazing motor before you now. Motors likes these focus on premium performance and reliability. The DIAVOLA Series! Fresh from the labs, this is the final product of months of designing, testing and finishing in order to deliver the most powerful motor possible while keeping a great ratio on reliability and price.
DIAVOLA 2207 comes in 1960Kv if preferred.
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 4~6S
Kv Rating: 1960Kv
Stator Size: 22x7mm
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 5mm
Max. Power: 901.3W
Internal Resistance: 60mΩ
Peak Current: 40.6A
Motor Dimensions: ɸ26.9x32.8mm
Mounting Dimensions: 16x16mm
Weight (Excl. Cable): 30.5g
Includes
1x CNHL Speedy Pizza Drones Axis Flying Diavola 2207 2020Kv Brushless Motors
All batteries must be shipped by a ground shipping method.
CNHL Ultra Black is a brand-new battery specifically designed for professional FPV racing competitions. It's got higher capacity, lower internal resistance, and lower landing temperatures.
Elevate your drone game with this CNHL Ultra Black Series 22.2V 6S 1050mAh 150C LiPo Battery-XT60. It features a superior power and lightweight design for a fast, reliable flight experience. - Enjoy the thrill of a 150C discharge rate!
Check out our selection of 6S batteries, and all our CNHL products!
MONSTER Power
Your only shop for RC lipo batteries.
CNHL offers superior RC Lipo batteries with higher performance at a more while maintaining high quality.
Specifications
Capacity: 1050mAh
Voltage: 22.2V / 6-Cell / 6S1P
Discharge Rate: 150C Continual / 300C Burst
Charge Rate: 5C Max
Size: 31x38x76mm
Weight: 180g
Output Connector: XT60
Balance Connector: JST / XH
Wire Size (AWG): 12#
Includes
1x CNHL Ultra Black Series 22.2V 6S 1050mAh 150C LiPo Battery - XT60
All batteries must be shipped by a ground shipping method.
CNHL Ultra Black is a brand-new battery specifically designed for professional FPV racing competitions. It's got higher capacity, lower internal resistance, and lower landing temperatures.
Elevate your drone game with this CNHL Ultra Black Series 22.2V 6S 1400mAh 150C LiPo Battery-XT60. It features a superior power and lightweight design for a fast, reliable flight experience. - Enjoy the thrill of a 150C discharge rate!
Check out our selection of 6S batteries, and all our CNHL products!
MONSTER Power
Your only shop for RC lipo batteries.
CNHL offers superior RC Lipo batteries with higher performance at a more affable cost while maintaining high quality.
Specifications
Capacity: 1400mAh
Voltage: 22.2V / 6-Cell / 6S1P
Discharge Rate: 150C Continual / 300C Burst
Charge Rate: 5C Max
Size: 39.5 x 39 x 78mm
Weight: 239g
Output Connector: XT60
Balance Connector: JST / XH
Wire Size (AWG): 12#
Includes
1x CNHL Ultra Black Series 22.2V 6S 1400mAh 150C LiPo Battery - XT60
All batteries must be shipped by a ground shipping method.
CNHL Ultra Black is a brand-new battery specifically designed for professional FPV racing competitions. It's got higher capacity, lower internal resistance, and lower landing temperatures.
Elevate your drone game with this CNHL Ultra Black Series 22.2V 6S 1550mAh 150C LiPo Battery-XT60. It features a superior power and lightweight design for a fast, reliable flight experience. - Enjoy the thrill of a 150C discharge rate!
Check out our selection of 6S batteries, and all our CNHL products!
MONSTER Power
Your only shop for RC lipo batteries.
CNHL offers superior RC Lipo batteries with higher performance at a more affable cost while maintaining high quality.
Specifications
Capacity: 1550mAh
Voltage: 22.2V / 6-Cell / 6S1P
Discharge Rate: 150C Continual / 300C Burst
Charge Rate: 5C Max
Size: 46x40x80mm
Weight: 256g
Output Connector: XT60
Balance Connector: JST / XH
Wire Size (AWG): 12#
Includes
1x CNHL Ultra Black Series 22.2V 6S 1550mAh 150C LiPo Battery - XT60
Pre-Orders shipping ASAP!
For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer.
DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ.
BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.
The 4S version comes with powerful 1504-3600Kv motors, and choose between PNP (No RX) or ELRS 2.4GHz for your receiver!
Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!
Features
Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high-cost performance；
It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster;
The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable;
The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash;
The independent action camera base can be used with naked GoPro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.
Specifications
Brand: DarwinFPV
Model: BabyApe Ⅱ 4S
Frame: Wide X
Wheelbase: 156mm
Size: 126mmx150mmx50mm
Flight Control: F411 MPU6500 AT7456E
Firmware：DARWINF411
Firmware: BETAFPV_Nano_2400_RX
The receiver's factory firmware is ELRS_V3.2.0
Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB
ESC: Bluejay 48KHz 3-6S 30A
Motor: 4S version：1504-3600KV
Propeller: HQProp T3.5x2x3GR-PC
Weight: 135.4 g (analog version)
Receiver: ELRS 2.4GHz
Darwin FPV "Cement" Ultra Durable FPV Drone Camera
Sensor type：1/3" CMOS Sensor
Image：16:9
TV System: NTSC
Horizontal Resolution：1200TVL
Lens：2.1mm 160°
Electronic Shutter: 1/50~1/100000 sec
Video Output: CVBS
Min. Illumination：0.001Lux
wb: automatic
DNR: 3D DNR
WDR: 100db
Input voltage: DC 3.7-24V
Working current：80mA@DC12V/170mA@DC5V
IP: IP67
Size：19x19mm
Weight：7.9g
DarwinFPV 25/200/400/600mW VTX
Output Power: 25/200/400/600mW(adjustable)
Frequency: 5.8Hz 40port
Power Supply Voltage Range: 5V
Weight: 3.5g
Pitch: 28x15mm(length x width)
Protocol: SmartAudio
Indicator Light Description:
Includes
1x DarwinFPV BNF Baby Ape V2 3.5" Analog Micro Quad - 4S - Choose Your Receiver
4x HQProp T3.5x2x3GR-PC
2x Battery cable strip ( 10x170mm)
2x EVA shock pad（thickness：10㎜）
1x Spare screws bag
1x Sticker
1x Manual
Pre-Orders shipping ASAP!
For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer.
DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ.
BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.
The 6S version comes with powerful 1504-2300Kv motors, and choose between PNP (No RX) or ELRS 2.4GHz for your receiver!
Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!
Features
Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high cost performance；
It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster;
The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable;
The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash;
The independent action camera base can be used with naked gopro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.
Specifications
Brand: DarwinFPV
Model: BabyApe Ⅱ 6S
Frame: Wide X
Wheelbase: 156mm
Size: 126mmx150mmx50mm
Flight Control: F411 MPU6500 AT7456E
Firmware： DARWINF411
Firmware: BETAFPV_Nano_2400_RX
The receiver's factory firmware is ELRS_V3.2.0
Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB
ESC: Bluejay 48KHz 3-6S 30A
Motor： 6S version：1504-2300KV
Propeller: HQProp T3.5x2x3GR-PC
Weight: 135.4 g(analog version)
Receiver: ELRS 2.4GHz
Darwin FPV "Cement" Ultra Durable FPV Drone Camera
Sensor type：1/3" CMOS Sensor
Image：16:9
TV System: NTSC
Horizontal Resolution：1200TVL
Lens：2.1mm 160°
Electronic Shutter: 1/50~1/100000 sec
Video Output: CVBS
Min. Illumination：0.001Lux
wb: automatic
DNR: 3D DNR
WDR: 100db
Input voltage: DC 3.7-24V
Working current：80mA@DC12V/170mA@DC5V
IP: IP67
Size：19x19mm
Weight：7.9g
DarwinFPV 25/200/400/600mW VTX
Output Power: 25/200/400/600mW(adjustable)
Frequency: 5.8Hz 40port
Power Supply Voltage Range: 5V
Weight: 3.5g
Pitch: 28x15mm(length x width)
Protocol: SmartAudio
Indicator Light Description:
Includes
1x DarwinFPV BNF Baby Ape V2 3.5" Analog Quad - 6S - Choose Your Receiver
4x HQProp T3.5x2x3GR-PC
2x Battery cable strip ( 10x170mm)
2x EVA shock pad（thickness：10㎜）
1x Spare screws bag
1x Sticker
1x Manual
DarwinFPV F411 3-6S FC is currently the cheapest in the FPV world and a direct replacement for the CineApe, designed to reduce the budget of entry-level FPV pilots as much as possible. At the same time, we have also filled the flight control with glue, which greatly reduces the risk of damage to components caused by frequent crashes by novices.
Check out our other flight controllers and our Darwin FPV products!
Specifications
Input Voltage: 3-6S
MCU: STM32F411
Gyro: MPU6500
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
Firmware: DARWINF411
BEC: 5V
Current Sensor: Yes
Barometer: BMP280
Black Box: SD Slot
Stack Size: 30x30 / 20x20
Dimensions: 37x37mm
Includes
1x DarwinFPV F411 3-6S 30x30 / 20x20 Flight Controller
This AIO has a rating of IP67, In ideal conditions submersion of 1 meter for 30 minutes can be achieved.
Introducing the all-new DarwinFPV Hulk AIO! Having IP67 water-resistant grading, 45A BLS ESC, and Onboard ELRS SPI receiver. This AIO is ready for any adventure that you can and couldn't take your drone!!!
Check out our other AIO Flight Controllers and our Darwin FPV products!
Specifications
AIO F411
MCU: STM32F411CEU6
Gyro: MPU6500
OSD Chip: Betaflight OSD AT7456E
Blackbox: 16MB
UARTS: 5
I2C: SDA / SLA pads
LED: Yes
Beeper: Yes
Firmware Target: MATEKF405
FC Mounting Pattern: 30x30mm
Dimensions: 37x36x10.8mm
AIO ESC
Input Voltage: 2-6S
Max. Continuous Current: 45A
Max. Burst Current: 55A
MCU: EFM8BB21F16G
Current Sensor: Yes
Mounting Dimensions: 25 x 25 M2
Dimensions 46.2mm x 39.5mm x 10mm
Includes
1x Darwin FPV HULK F411/45A 3-6S AIO w/ ELRS 2.4GHz
Please attention:
Seawater is highly corrosive, it is not recommended for use in seawater. Please wash it with fresh water immediately and then dry it.
Supports a 3-6S battery, remember not to plug the battery's positive and negative interface in reverse, otherwise, it will burn out.
After receiving the AIO, first connect to a computer on Betaflight software to check whether the gyroscope and accelerometer are detected and whether the gyroscope attitude is normal.
Increase the throttle in Betaflight software to ensure the normal rotation and correct rotation direction of the 4 motors, and then install the propellers for a test flight; be sure to remove the propellers when pulling the throttle in Betaflight software to avoid accidents.
After confirming the above precautions without any problems, you can install the propellers and start flying!
Wiring Diagram
Diatone Mamba Micro 2A SWITCHABLE BEC 5V/9V for DJI Air Unit! This unit conveniently switches between a 5v and 9v output at 2 Amps!
Check out all our BECs and our Diatone products!
Specifications
Output: 5V/2A and 9V/2A switchable
Output 5V: input 7~25.2v
Output 9V: input 12~25.2v
Product Size：16×10mm
Weight: 1.6g
Includes
1x Diatone 2-6S Mamba Micro BEC 2A 5V/9V for DJI Air Unit
Experience reliable power with the Diatone Mamba 5 Reactor 32Bit 44A 4-6S 20x20 4in1 ESC. This advanced ESC is designed to provide you with precise and smooth control for your quadcopter. Enjoy a responsive feel and the responsiveness of your craft, thanks to its 32-bit processor.
Check out all our 20x20 ESCs and all our Diatone Gear!
Specification
Input voltage: 4~6S Lipo (16.8V~25.2V)
Continue Current: 44A×4
Burst current: 54A (10S)
BEC: No
Target： BLHeli_32 MAMBA5_Reactor_44
SOFT: DSHOT300/600/1200/MAX2400（FETTEC）
PWM: 24~128K
Mounting size: 20mm, M2
Includes
1x Diatone Mamba 5 Reactor 32Bit 44A 4-6S 20x20 4in1 ESC
2x 8pin sh1.0
1x AMASS Original XT60
1x High Frequency 470uF/35V
The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro.
Check out all our 30x30 FCs and all our Diatone Gear!
Specifications
MCU: STM32F722
GYRO: IMC42688P
Barometer: Yes
OSD: Yes
Blackbox: 16M Flash Memory
Uarts: 6Set
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED/MB LED
F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 3-6S Lipo
TVS Protection: Yes
BEC: 3.3V/0.5A, & 5V/3A, and 9V/3A
Mounting: 30.5x30.5mm, M3
Includes
1x Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller
5x M3 ESC Isolation Dampers
5x M3 Silicone Dampers
1x 6-Pin Air Unit Cable
2x 8-Pin Cable
Wiring Diagram
Diatone takes a shot at the new trend of ultra smooth 128k ESCs. Diatone's consistent quality and performance make this a great option for those looking to experiment with a 128k ESC build.
Check out the rest of our 4in1 ESCs and Diatone gear!
Specifications
Input Voltage: 2~6S
Max Continuous Current: 40A
Max Burst Current: 45A
BEC: No
Target：BLHeli_32 MAMBA F40_128K_MINI
Protocol: Dshot300/600/1200
PWM Range: 24~128K
TVS Protection: Yes
Mounting Pattern: 20x20 M2/M3
Includes
Diatone Mamba F40 Mini 128k 32Bit 40A 2-6S 4in1 ESC
2x 8pin sh1.0
1x AMASS XT60
1x High-Frequency 470uF/35V Capacitor
A great ESC with plenty of power at a desirable price point.
Check out the rest of our 4in1 ESCs and Diatone gear!
Specifications
Input Voltage: 3-6s (12.6-25.2v)
Continuous Current: 50Ax4
Burst Current: 60A (10s)
BEC: No
Software: DShot300/600
BLHeli_S CH40
TVS Protection: Yes
Mounting: 30x30mm M3
Includes
1x Diatone Mamba F50_BLS 50A 3-6S 30x30 4in1 ESC
Diatone takes a shot at the new trend of ultra smooth 128k ESCs. Diatone's consistent quality and performance make this a great option for those looking to experiment with a 128k ESC build.
Check out the rest of our 4in1 ESCs and Diatone gear!
Specifications
Input Voltage: 3~6S Lipo (12.6V~25.2V)
Max Continuous Current: 55A
Max Burst Current: 65A
BEC: No
Target：BLHeli_32 MAMBA F55_128K
Protocol: Dshot300/600/1200
PWM Range: 24~128K
TVS Protection: Yes
Mounting Pattern: 30x30 M3
Includes
1x Diatone Mamba F55 128K 32Bit 55A 3-6S 30x30 4in1 ESC
2x 8pin sh1.0
1x AMASS XT60
1x High-Frequency 470uF/35V Capacitor
Diatone takes a shot at the new trend of ultra smooth 128k ESCs. Diatone's consistent quality and performance make this a great option for those looking to experiment with a 128k ESC build.
Check out the rest of our 4in1 ESCs and Diatone gear!
Specifications
Input Voltage: 3~6S Lipo (12.6V~25.2V)
Max Continuous Current: 65A
Max Burst Current: 75A
BEC: No
Target：BLHeli_32 MAMBA F65_128K
Protocol: Dshot300/600/1200
PWM Range: 24~128K
TVS Protection: Yes
Mounting Pattern: 30x30 M3
Includes
1x Diatone Mamba F65 128K 32Bit 65A 3-6S 30x30 4in1 ESC
2x 8pin sh1.0
1x AMASS XT60
1x High-Frequency 470uF/35V Capacitor
The Mamba F405 Mini flight controller is tried and true. This has plenty of features to suit the needs of most quads and pilots. The small for factor and overall reliability make this an excellent choice for almost any build!
Check out all of our 20x20 FCs and all our Diatone Gear!
Specifications
Input Voltage: 3-6S
MCU: 480MHz STM32F405
Gyro: ICM42688P
OSD: AT7456E
Blackbox: 16M Flash Memory
Uarts: 6Set
ESC Signal: 6Set
LED Controller: BF LED
I2C: Yes
F.Port: Yes
Buzz: Yes
TVS Protection: Yes
BEC: 3.3V 0.5A & 5V 2.5A & 9V 2A
Mounting Pattern: 20x20 M3/M2
Dimensions: 29x29.5x6.5
Weight: 6g
Includes
1x Diatone Mamba MK4 F405 Mini 20x20 Flight Controller
Wiring Diagram
Diatone has released their 4th generation F722 mini stack. The MK4 F722 mini 20x20 stack boasts larger soldering pads, wider pad spacing, more UARTs, l2C and is configurable through the Speedy Bee App via built-in Wi-Fi! So much power from a lightweight stack!
Browse our Stacks & Combos and our Diatone Gear!
Features
The pad area increased by 30%
Pad spacing increased by 100%
MP9943 synchronous rectifier BEC
MINI series upgrade DJI interface and 5v 15W/9V 18W 2 set BEC
USB Type C
6 Set UART and I2C
4 Set Power Protection
32Bit ESC all support 128K
Mini series FC uses 2mm and 3mm mounting holes, w/ a special dampening ring
Upgrade the twisted pair anti-jamming cable and reinforcement process
Specifications
Mamba Basic Mini F722 MK4
Input: 2-6S
MCU: ICM42688P
Barometer: Yes
OSD: Yes
Blacbox: 16M Flash Memory
Uarts: 6Set
Protocol: Dshot300/600/1200
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED
F.Port: Yes
Buzz: Yes
TVS Protection: Yes
BEC: 3.3V 0.5A & 5V 2.5A
Mounting Pattern: 20x20 M3/M2
Mamba F40 128k
Input Voltage: 3-6S Lipo
Max Continuous Current: 40A
Max Burst Current: 45A
BEC: No
Target：BLHeli_32 MAMBA F40_128K_MINI
Protocol: Dshot300/600/1200
PWM Range: 24~128K
TVS Protection: Yes
Mounting Pattern: 20x20 M2/M3
Includes
1x Diatone Mamba Basic MK4 F722 Mini F40_128k 2-6S 20x20 Stack/Combo
5x M2 Silicone Grommets
5x M3 Silicone Grommets
5x M2 ESC Isolation Columns
5x M3 ESC Isolation Columns
1x 8 Pin single-ended cable for flight controller
2x 8 Pin Cable
1x 6 Pin Air Unit Cable
1x XT60
1x Capacitor
Wiring Diagram
Now this is something truly special for its size and capability - Introducing the Diatone Mamba MK4 F740 AIO. The Diatone Mamba MK4 F740 AIO is a powerful, all-in-one flight controller and ESC for sub 250g 3, 4, and 5 inch quads. It is equipped with an F7 processor, a 32bit 4in1 ESC of up to 40A, a barometer and OSD chip, and 16M of Blackbox memory. Connecting a video transmitter is easy and efficient, giving you a reliable and versatile system.
Check out all our Whoop/AIO Flight Controllers and our full Diatone collection!.
FC Specifications
Target: MAMBA F722_2022B
MCU: 216MHz STM32F722
GYRO: ICM-42688-P
Barometer: Yes
OSD: Yes
Blacbox: 16MB Flash
Uarts: 6 Set
Motor Signal: 4 Set
ESC Soft: Dshot300/600
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED
AIR UNIT Port: Yes
WIFI: No
F.Port: Yes
RSSI: No
Buzz: Yes
Input: 3~6S Lipo (12.6~25.2V)
BEC Protection: Yes
Receiver Protection: Yes
TVS Protection: Yes
BEC: 3.3V 0.5A & 5V 2A
Mounting size: 25.5 x 25.5mm/M2
ESC Specifications
Input: 3~6S Lipo (12.6~25.2V)
Continue Current: 40Ax4
Burst current: 45A (10 Seconds)
Target：BLHeli_32 MAMBA F40_128K
SOFT: Dshot300/600
PWM:24~128K
Include
1x Diatone Mamba MK4 F740 3-6S AIO Whoop/Toothpick Flight Controller w/ 40A 32bit 4in1 ESC - WIFI
1x High Frequency 470uF/35V
1x AIR UNIT sh1.0
1x 16AWG 60mm
1x AMASS Original XT60
Wiring Diagram
Please notice：This AIO only supports Alpha and does not support BetaFlight
Alpha: https://gui.fettec.net/FC/index.html
Flight controllers that use Aphla are known to be the best for freestyling, for smoothness and reliability. Diatone is delivering on next-gen premium FPV parts, especially seen with the MK5 AIO. Capable of supporting up to 40 amps of power while working off metal mosfets, for better performance. You are going to want to put this on your next 3-4 inch freestyle ripper.
Check out all our Whoop/AIO Flight Controllers and our full Diatone collection!.
Features
Metal Mosfets
Comes with a User Manual with a Wiring Diagram
PWM: 24~128K
HD Compatible
Specification
FC Specifications
Target： Alpha
MCU: 170MHz STM32G473
GYRO: IIM-42652
OSD: Yes
Uarts: 4 Set
Motor Signal:4 Set
ESC Soft: Dshot300/600/1200/2400
Power Led: Yes
LED Controller: Yes
AIR UNIT Port: Yes
Buzz: Yes
Input: 4~6S Lipo (14.8~25.2V)
BEC Protection: Yes
Receiver Protection: Yes
TVS Protection: Yes
BEC: 10V 2A& 5V 2A
Mounting size: 25.5×25.5mm/M2
Overall dimensions: 35×34.5×6.5mm
ESC Specifications
Input: 4~6S Lipo (14.8~25.2V)f
Continue Current: 40A×4
Burst current: 45A (10S)
Target：BLHeli_32 MAMBA F40_128K
SOFT: Dshot300/600/1200/2400
PWM:24~128K
Includes
1x Diatone Mamba MK5 G4 4-6S AIO Whoop/Toothpick Flight Controller w/ 40A 32Bit 4in1 ESC - DSHOT2400
1x High Frequency 470uF/35V
1x AIR UNIT sh1.0 connector
2x 16AWG 60mm
1x AMASS Original XT60
Mean green Diatone racing motors, a must-have for those toothpick race builds.
Check out the rest of our micro motors, as well as the rest of our Diatone selection!
Specifications
Kv: 3000Kv
Input Voltage: 3-6S LiPo
Configuration: 9N12P
Max Continuous Current: 11.95A
Internal Resistance: 310mΩ
Motor Dimensions: Φ20.5mm x 15mm
Stator Dimensions: Φ14mm x 4mm
Shaft Diameter: 1.5mm
Mounting Pattern: Φ12mm
Wire Dimensions: 24AWG x 150mm
Weight (w/ wires): 10.5g
Includes
1x Diatone Mamba Toka 1404 3000Kv Micro Motor
Diatone Roma F4 4 inch Long Range Frame Kit weighs only 47G with T300 3k carbon fiber, made for both 9 and 12mm motor mounting, in the deadcat configuration for props out of view!
Check out our Diatone Roma F4 LR Collection!
Check out the rest of our 4" frames, our Diatone gear!
Specifications
Wheelbase：176mm
Weight：47g
Prop Size：4inch
FC Mounting: 20x20/26.5x26.5m（M2）
Motor Mounting: 9mm/12mm
Camera Spacing: 20mm
Top Plate: 1.5mm
Medium Plate: 1.5mm
Bottom Plate: 1.5mm
Arm: 3mm
Rated Voltage (Recommendation：4S~6S
Aluminum alloy：7075
Carbon fiber: T300 3K
Includes
1x Diatone Roma F4 LR 4" Frame
All batteries must be shipped by a ground shipping method.
Discover the Dogcom brand and its high quality and stable Lipos batteries. Dogcom makes high quality batteries, with stable chemistry for safer storage and use, lower internal resistance for high discharge rates, and a long life cycle!
Check out all our 6S packs and our entire Dogcom collection!
Specifications
Capacity: 1550mAh
Continuous Discharge Rate: 150C
Dimensions: 78x38x43mm
Balance Lead: JST-XH
Discharge Lead: XT60
Weight: 260g (+/- 1%)
Includes
1x DogCom 22.2V 6S 1550mAh 150C Lipo Battery - XT60
The engineers at EMAX are always seeking ways to design the ultimate motor with brushless technology. In their efforts, they produced the ECO II Series, a new line of brushless motors further improving on the performance and durability while retaining the same affordability.Redesigned from the ground up, the ECO II boasts an all new architecture. With a more rounded design paired together with thicker reinforcements, maximum durability is achieved. Finished with a reflective surface, the ECO II offers a sleek modern design destined to satisfy the need for both aesthetics and durability.In order to improve the performance from its predecessor, the ECO II utilizes N52SH arc magnets over prior N48 magnets, allowing more powerful throttle response and higher RPMs to be achieved. More torque and thrust is generated, allowing pilots the flexibility to comfortably meet the demands of any racetrack or flight situation.The ECO II Series marks the next evolution in affordable brushless motor technology, bringing in a new era of performance for everyone.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
A brand new design with a rounded bell and stronger attachment points for increased durability
Fully mirror-polished finish that shines and glistens with even the smallest hint of light
Upgraded N52SH curved arc magnets for tighter airgap and better performance
Precision NSK bearing for unparalleled smooth operation
Specifications
Kv: 2000
Input Voltage: 4-6S
Configuration: 12N14P
Motor Dimensions: 24.7*19.2mm
Stator Dimensions: 20*4mm
Shaft Diameter: 1.5mm
Wire Dimensions: 120mm 24awg
Mounting Pattern: 12*12mm
Weight (w/ wires): 18g
Includes
1x EMAX ECO II 2004 2000Kv Motor
The engineers at EMAX are always seeking ways to design the ultimate motor with brushless technology. In their efforts, they produced the ECO II Series, a new line of brushless motors further improving on the performance and durability while retaining the same affordability.Redesigned from the ground up, the ECO II boasts an all new architecture. With a more rounded design paired together with thicker reinforcements, maximum durability is achieved. Finished with a reflective surface, the ECO II offers a sleek modern design destined to satisfy the need for both aesthetics and durability.In order to improve the performance from its predecessor, the ECO II utilizes N52SH arc magnets over prior N48 magnets, allowing more powerful throttle response and higher RPMs to be achieved. More torque and thrust is generated, allowing pilots the flexibility to comfortably meet the demands of any racetrack or flight situation.The ECO II Series marks the next evolution in affordable brushless motor technology, bringing in a new era of performance for everyone.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
A brand new design with a rounded bell and stronger attachment points for increased durability
Fully mirror-polished finish that shines and glistens with even the smallest hint of light
Upgraded N52SH curved arc magnets for tighter airgap and better performance
Precision NSK bearing for unparalleled smooth operation
Specifications
Kv: 2400
Input Voltage: 4-6S
Configuration: 12N14P
Motor Dimensions: 24.7*19.2mm
Stator Dimensions: 20*4mm
Shaft Diameter: 1.5mm
Wire Dimensions: 120mm 24awg
Mounting Pattern: 12*12mm
Weight (w/ wires): 18g
Includes
1x EMAX ECO II 2004 2400Kv Motor
The engineers at EMAX are always seeking ways to design the ultimate motor with brushless technology. In their efforts, they produced the ECO II Series, a new line of brushless motors further improving on the performance and durability while retaining the same affordability.Redesigned from the ground up, the ECO II boasts an all new architecture. With a more rounded design paired together with thicker reinforcements, maximum durability is achieved. Finished with a reflective surface, the ECO II offers a sleek modern design destined to satisfy the need for both aesthetics and durability.In order to improve the performance from its predecessor, the ECO II utilizes N52SH arc magnets over prior N48 magnets, allowing more powerful throttle response and higher RPMs to be achieved. More torque and thrust is generated, allowing pilots the flexibility to comfortably meet the demands of any racetrack or flight situation.The ECO II Series marks the next evolution in affordable brushless motor technology, bringing in a new era of performance for everyone.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
A brand new design with a rounded bell and stronger attachment points for increased durability
Fully mirror-polished finish that shines and glistens with even the smallest hint of light
Upgraded N52SH curved arc magnets for tighter airgap and better performance
Precision NSK bearing for unparalleled smooth operation
Specifications
Kv: 3000
Input Voltage: 3-6S
Configuration: 12N14P
Motor Dimensions: 24.7*19.2mm
Stator Dimensions: 20*4mm
Shaft Diameter: 1.5mm
Wire Dimensions: 120mm 24awg
Mounting Pattern: 12*12mm
Weight (w/ wires): 18g
Includes
1x EMAX ECO II 2004 3000Kv Motor
The Emax RSIII motor is rated at 2207, which is a classic stator size for racing and freestyle, and works off 1800Kv, which is ideal for 6S 5" quads.
Behold the RS3 (Race Spec III) motor from EMAX—the perfect fusion of top-level performance and an affordable price point. Designed from the ground up for drone racing, the RSIII optimizes voltages up to 6S LiPOs, while its 4mm Titanium alloy bearing shaft ensures smooth and efficient rotations. Get ready to experience unimaginable speed, total precision, and unmatched endurance—the RSIII is ready to revolutionize the racing circuit!
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Prepare to redefine your drone racing experience with RSIII, the latest entry in the legendary lineage of EMAX high-performance motors. Embrace precision engineering, unmatched reliability, and lightweight design, tailored to elevate your racing prowess.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
Precision bearing
Titanium alloy shaft
Anodizing
16x16mm hole pattern
Multi-strand winding
120mm 20 AWG silicone wire
Staggeringly light 29.3g with 2cm wires for the 2207 size makes the EMAX RS3 one of the lightest racing motors available. Available in 1800kv/2100kv/2500kv as well as 2306 stator size for those who desire a lightweight freestyle motor or low end torque race motor.
While the RS3 is extremely lightweight, no attention was spared towards the durability of this platform. EMAX took what they learned with the near indestructible ECO II line and applied this to the RS3 to provide high performance without the sacrifice of durability that many race motors make.
The RS3 has been under testing for the last 6 months with the fastest pilots on the planet to truly test the limits in terms of capability to withstand heat. The feedback from these pilots has been that the EMAX RS3 withstands excessive heat on 2100kv 6S without burning unlike any other motor they have tested to date.
Specifications
Framework: 12N14P
Length: 33mm
Diameter: 26.9mm
No.of cells: 3-6S 1800KV
Propeller: 5"-5.5"
Weight: 29.3g(W/O Silicone Wire) 1800KV
Prop adapter shaft thread: M5
Bearing Shaft: 4mm
Shaft Thread: CW
Lead: 20#AWG 120mm
Idle Current (10V): 1.1A
Internal Resistance: 72mΩ
Peak Current (6S): 43A
Max Power (6S): 1080W
Includes
1x Emax RSIII Series 2207 1800Kv Motor
5x M3x8 Screw
5x M3x7 Screw
5x M3x6 Screw
1x Aluminum M5 nylock nut
1x Washer and Screw for shaft
The Emax RSIII motor is rated at 2207, which is a classic stator size for racing and freestyle, and works off 2100Kv, which is ideal for 4-6S 5" quads.
Behold the RS3 (Race Spec III) motor from EMAX—the perfect fusion of top-level performance and an affordable price point. Designed from the ground up for drone racing, the RSIII optimizes voltages up to 6S LiPOs, while its 4mm Titanium alloy bearing shaft ensures smooth and efficient rotations. Get ready to experience unimaginable speed, total precision, and unmatched endurance—the RSIII is ready to revolutionize the racing circuit!
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Prepare to redefine your drone racing experience with RSIII, the latest entry in the legendary lineage of EMAX high-performance motors. Embrace precision engineering, unmatched reliability, and lightweight design, tailored to elevate your racing prowess.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
Precision bearing
Titanium alloy shaft
Anodizing
16x16mm hole pattern
Multi-strand winding
120mm 20 AWG silicone wire
Staggeringly light 29.3g with 2cm wires for the 2207 size makes the EMAX RS3 one of the lightest racing motors available. Available in 1800kv/2100kv/2500kv as well as 2306 stator size for those who desire a lightweight freestyle motor or low end torque race motor.
While the RS3 is extremely lightweight, no attention was spared towards the durability of this platform. EMAX took what they learned with the near indestructible ECO II line and applied this to the RS3 to provide high performance without the sacrifice of durability that many race motors make.
The RS3 has been under testing for the last 6 months with the fastest pilots on the planet to truly test the limits in terms of capability to withstand heat. The feedback from these pilots has been that the EMAX RS3 withstands excessive heat on 2100kv 6S without burning unlike any other motor they have tested to date.
Specifications
Framework: 12N14P
Length: 33mm
Diameter: 26.9mm
No.of cells: 3-6S 2100KV
Propeller: 5"-5.5"
Weight: 29.4g(W/O Silicone Wire) 2100KV
Prop adapter shaft thread: M5
Bearing Shaft: 4mm
Shaft Thread: CW
Lead: 20#AWG 120mm
Idle Current (10V): 1.5A
Internal Resistance: 54mΩ
Peak Current (6S): 50A
Max Power (6S): 1260W
Includes
1x Emax RSIII Series 2207 2100Kv Motor
5x M3x8 Screw
5x M3x7 Screw
5x M3x6 Screw
1x Aluminum M5 nylock nut
1x Washer and Screw for shaft
The Emax RSIII motor is rated at 2207, which is a classic stator size for racing and freestyle, and works off 2500Kv, which is ideal for 4S 5" quads.
Behold the RS3 (Race Spec III) motor from EMAX—the perfect fusion of top-level performance and an affordable price point. Designed from the ground up for drone racing, the RSIII optimizes voltages up to 4S LiPOs, while its 4mm Titanium alloy bearing shaft ensures smooth and efficient rotations. Get ready to experience unimaginable speed, total precision, and unmatched endurance—the RSIII is ready to revolutionize the racing circuit!
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Prepare to redefine your drone racing experience with RSIII, the latest entry in the legendary lineage of EMAX high-performance motors. Embrace precision engineering, unmatched reliability, and lightweight design, tailored to elevate your racing prowess.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
Precision bearing
Titanium alloy shaft
Anodizing
16x16mm hole pattern
Multi-strand winding
120mm 20 AWG silicone wire
Staggeringly light 29.3g with 2cm wires for the 2207 size makes the EMAX RS3 one of the lightest racing motors available. Available in 1800kv/2100kv/2500kv as well as 2306 stator size for those who desire a lightweight freestyle motor or low end torque race motor.
While the RS3 is extremely lightweight, no attention was spared towards the durability of this platform. EMAX took what they learned with the near indestructible ECO II line and applied this to the RS3 to provide high performance without the sacrifice of durability that many race motors make.
The RS3 has been under testing for the last 6 months with the fastest pilots on the planet to truly test the limits in terms of capability to withstand heat. The feedback from these pilots has been that the EMAX RS3 withstands excessive heat on 2100kv 6S without burning unlike any other motor they have tested to date.
Specifications
Framework: 12N14P
Length: 33mm
Diameter: 26.9mm
No.of cells: 3-4S 2500Kv
Propeller: 5"-5.5"
Weight: 29.4g(W/O Silicone Wire) 2500Kv
Prop adapter shaft thread: M5
Bearing Shaft: 4mm
Shaft Thread: CW
Lead: 20#AWG 120mm
Idle Current (10V): 2.1A
Internal Resistance: 42mΩ
Peak Current (6S): 45A
Max Power (6S): 750W
Includes
1x Emax RSIII Series 2207 2500Kv Motor
5x M3x8 Screw
5x M3x7 Screw
5x M3x6 Screw
1x Aluminum M5 nylock nut
1x Washer and Screw for shaft
The Emax RSIII motor is rated at 2306, which is a classic stator size for racing and freestyle, and works off 1800Kv, which is ideal for 6S 5" quads.
Behold the RS3 (Race Spec III) motor from EMAX—the perfect fusion of top-level performance and an affordable price point. Designed from the ground up for drone racing, the RSIII optimizes voltages up to 6S LiPOs, while its 4mm Titanium alloy bearing shaft ensures smooth and efficient rotations. Get ready to experience unimaginable speed, total precision, and unmatched endurance—the RSIII is ready to revolutionize the racing circuit!
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Prepare to redefine your drone racing experience with RSIII, the latest entry in the legendary lineage of EMAX high-performance motors. Embrace precision engineering, unmatched reliability, and lightweight design, tailored to elevate your racing prowess.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
Precision bearing
Titanium alloy shaft
Anodizing
16x16mm hole pattern
Multi-strand winding
120mm 20 AWG silicone wire
Staggeringly light 29.3g with 2cm wires for the 2207 size makes the EMAX RS3 one of the lightest racing motors available. Available in 1800kv/2100kv/2500kv as well as 2306 stator size for those who desire a lightweight freestyle motor or low end torque race motor.
While the RS3 is extremely lightweight, no attention was spared towards the durability of this platform. EMAX took what they learned with the near indestructible ECO II line and applied this to the RS3 to provide high performance without the sacrifice of durability that many race motors make.
The RS3 has been under testing for the last 6 months with the fastest pilots on the planet to truly test the limits in terms of capability to withstand heat. The feedback from these pilots has been that the EMAX RS3 withstands excessive heat on 2100kv 6S without burning unlike any other motor they have tested to date.
Specifications
Framework: 12N14P
Length: 32mm
Diameter: 27.3mm
No.of cells: 3-6S 1800Kv
Propeller: 5"-5.5"
Weight: 27.9g(W/O Silicone Wire) 1800Kv
Prop adapter shaft thread: M5
Bearing Shaft: 4mm
Shaft Thread: CW
Lead: 20#AWG 120mm
Idle Current (10V): 1.1A
Internal Resistance: 68mΩ
Peak Current (6S): 34A
Max Power (6S): 860W
Includes
1x Emax RSIII Series 2306 1800Kv Motor
5x M3x8 Screw
5x M3x7 Screw
5x M3x6 Screw
1x Aluminum M5 nylock nut
1x Washer and Screw for shaft
The Emax RSIII motor is rated at 2306, which is a classic stator size for racing and freestyle, and works off 2100Kv, which is ideal for 4-6S 5" quads.
Behold the RS3 (Race Spec III) motor from EMAX—the perfect fusion of top-level performance and an affordable price point. Designed from the ground up for drone racing, the RSIII optimizes voltages up to 6S LiPOs, while its 4mm Titanium alloy bearing shaft ensures smooth and efficient rotations. Get ready to experience unimaginable speed, total precision, and unmatched endurance—the RSIII is ready to revolutionize the racing circuit!
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Prepare to redefine your drone racing experience with RSIII, the latest entry in the legendary lineage of EMAX high-performance motors. Embrace precision engineering, unmatched reliability, and lightweight design, tailored to elevate your racing prowess.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
Precision bearing
Titanium alloy shaft
Anodizing
16x16mm hole pattern
Multi-strand winding
120mm 20 AWG silicone wire
Staggeringly light 29.3g with 2cm wires for the 2207 size makes the EMAX RS3 one of the lightest racing motors available. Available in 1800kv/2100kv/2500kv as well as 2306 stator size for those who desire a lightweight freestyle motor or low end torque race motor.
While the RS3 is extremely lightweight, no attention was spared towards the durability of this platform. EMAX took what they learned with the near indestructible ECO II line and applied this to the RS3 to provide high performance without the sacrifice of durability that many race motors make.
The RS3 has been under testing for the last 6 months with the fastest pilots on the planet to truly test the limits in terms of capability to withstand heat. The feedback from these pilots has been that the EMAX RS3 withstands excessive heat on 2100kv 6S without burning unlike any other motor they have tested to date.
Specifications
Framework: 12N14P
Length: 32mm
Diameter: 27.3mm
No.of cells: 3-6S 2100Kv
Propeller: 5"-5.5"
Weight: 27.8g(W/O Silicone Wire) 2100Kv
Prop adapter shaft thread: M5
Bearing Shaft: 4mm
Shaft Thread: CW
Lead: 20#AWG 120mm
Idle Current (10V): 1.4A
Internal Resistance: 57mΩ
Peak Current (6S): 46A
Max Power (6S): 1160W
Includes
1x Emax RSIII Series 2306 2100Kv Motor
5x M3x8 Screw
5x M3x7 Screw
5x M3x6 Screw
1x Aluminum M5 nylock nut
1x Washer and Screw for shaft
The Emax RSIII motor is rated at 2306, which is a classic stator size for racing and freestyle, and works off 2500Kv, which is ideal for 4S 5" quads.
Behold the RS3 (Race Spec III) motor from EMAX—The perfect fusion of top-level performance and an affordable price point. Designed from the ground up for drone racing, the RSIII optimizes voltages up to 4S LiPOs, while its 4mm Titanium alloy bearing shaft ensures smooth and efficient rotations. Get ready to experience unimaginable speed, total precision, and unmatched endurance—The RSIII is ready to revolutionize the racing circuit!
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Engineered for strength and endurance, the RSIII motors feature a robust 4mm Titanium alloy bearing shaft. This innovation ensures smooth and efficient rotation, making every racing maneuver feel effortless and precise.
Prepare to redefine your drone racing experience with RSIII, the latest entry in the legendary lineage of EMAX high-performance motors. Embrace precision engineering, unmatched reliability, and lightweight design, tailored to elevate your racing prowess.
Have a look at the rest of our EMAX products, and our entire selection of motors!
Features
Precision bearing
Titanium alloy shaft
Anodizing
16x16mm hole pattern
Multi-strand winding
120mm 20 AWG silicone wire
Staggeringly light 29.3g with 2cm wires for the 2207 size makes the EMAX RS3 one of the lightest racing motors available. Available in 1800kv/2100kv/2500kv as well as 2306 stator size for those who desire a lightweight freestyle motor or low end torque race motor.
While the RS3 is extremely lightweight, no attention was spared towards the durability of this platform. EMAX took what they learned with the near indestructible ECO II line and applied this to the RS3 to provide high performance without the sacrifice of durability that many race motors make.
The RS3 has been under testing for the last 6 months with the fastest pilots on the planet to truly test the limits in terms of capability to withstand heat. The feedback from these pilots has been that the EMAX RS3 withstands excessive heat on 2100kv 6S without burning unlike any other motor they have tested to date.
Specifications
Framework: 12N14P
Length: 32mm
Diameter: 27.3mm
No.of cells: 3-4S 2500Kv
Propeller: 5"-5.5"
Weight: 27.7g(W/O Silicone Wire) 2500Kv
Prop adapter shaft thread: M5
Bearing Shaft: 4mm
Shaft Thread: CW
Lead: 20#AWG 120mm
Idle Current (10V): 1.8A
Internal Resistance: 43mΩ
Peak Current (6S): 43A
Max Power (6S): 720W
Includes
1x Emax RSIII Series 2306 2500Kv Motor
5x M3x8 Screw
5x M3x7 Screw
5x M3x6 Screw
1x Aluminum M5 nylock nut
1x Washer and Screw for shaft
FETtec has released a 4-In-1 8S 65A DShot 2400 ESC to complement the FETtec Flight Controllers and KISS Flight Controllers. With full sine wave control and all the latest features, this is the perfect ESC to pair with the new flight controller.
Check out all our KISS compatible gear, and everything FETtec!
Features
No more capacitors close to the mounting holes
Specifications
Active current limiting @ 65A
Input voltage: 3S-8S
High quality 40V MOSFETs
STM32G071 @ 64MHz
128 kHz Motor PWM
Full sine wave control
Soldering holes for up to 5 additional capacitors
KISS FC Passthrough
Betaflight Passthrough (available in 4.1)
Automatic input signal detection:Dshot 300-2400,PWM,OneShot 42/125,OneWire BUS with up to 8kHz looptime (one cable for all Motorsignals and Telemetry),S2M
Firmware:
New FETtec Firmware
FETtec Configurator for updated, configuration and telemetry. Standalone for MacOS, Windows 32 & 64 bit and Chrome Plugin
FETtec 4in1 ESC 65A Manual
FETtec Configurator
Includes
1x FETtec 65A 3-6S 30x30 4in1 ESC
The FETtec FC G4 V1.7 features the latest STM32G4 processor. Providing unparalleled processing power to your aircraft. Along with an IIM-42652 SPI gyro, two 5v BECs, 6-27V (2-6S) power handling, and a host of other features, the G4 from FETtec is on the cutting edge of Flight Controller technology.
Check out our other flight controllers, as well as the rest of our FETtec selection!
Dimensions:
Maximum outside dimensions: 37,2 x 37,2mm, without outside tips 30 x 30mm
Mounting hole arrangement:
20 x 20mm with M2 mounting hole (expandable to M3)
30 x 30mm with M3 mounting hole
30 x 30mm mounting hole tips are removable to reduce overall FC size
Specifications
Input Voltage: 2-6S LiPo
MCU: Latest STM32G473 Processor (w/ 180Mhz + Math accelerator)
Gyro: IIM-42652 SPI
OSD: YES
UARTs: 5 Sets
ESC Connections: Yes
Firmware: KISS firmware
BEC: 5V, 16V
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
DJI Compatible: Yes
Mounting Pattern: 30x30 / 20x20
Dimensions: 37.2x37.2mm
Weight: 5.37g
Available downloads:
Download FETtec FC G4 manual
Download FETtec FC G4 v1.7 manual
Includes
1x Fettec FC G4 V1.7 2-6S 30x30 / 20x20 Flight Controller
1x 8 pin cable (open on one side)
1x 6 pin cable (open on one side)
1x 4 pin calbe (open on one side)
Introducing the new FETtec Motor FM2004T 1800kv FPV Drone Motors. Not are they only fast but they're also meant to be durable and smooth. Step up your FETtec build with these amazing motors!!
Check out our other motors and all of our FETtec products!
Specifications
Kv: 1800Kv
Prop Shaft Diameter: 1.5mm
Rated Voltage: 4-6S
Config: 12N14P
Stator Dimension: 2004
Mounting Pattern: 12mmΦ
Shaft Diameter: 1.5mm
Weight: 17g
Includes
1x FETtec Motor FM2004T 1800kv Motor
The FETtec KISS G4-N 2-6S 30x30 / 20x20 Flight Controller features the latest STM32G4 processor. Providing unparalleled processing power to your aircraft. Along with an MPU6000 gyro, two 5v BECs, 6-27V (2-6S) power handling, and a host of other features, the G4 from FETtec is on the cutting edge of Flight Controller technology.
Note: This G4-N is a variation on the original G4 and is optimized for digital use. If you are flying analog, you will need the original G4 with built-in OSD chip.
Check out our other flight controllers, as well as the rest of our FETtec selection!
Specifications
Input Voltage: 2-6S LiPo
MCU: STM32G4
Gyro:IIM-42652 SPI
OSD: No
UARTs: 5 Sets
ESC Connections: Yes
Firmware: KISS firmware
BEC: 3.3V, 5V, 16V
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
DJI Compatible: Yes
Mounting Pattern: 30x30 / 20x20
Dimensions: 37.2x37.2mm
Weight: 5.37g
Includes
1x FETtec KISS G4-N 2-6S 30x30 / 20x20 Flight Controller
1x Capacitor
1x Wiring Harness
Enhance your RC car, wing, and quad with FETtec Race Wire 6 3-6S RGB LEDs (2pc). Constructed with advanced FET technology and high-quality components these LEDs are designed for maximum performance and reliability. With 3-6S adjustable voltage, these LEDs offer a bright and colorful light show that you can rely on.
Check out all our LEDs and all of our FETtec products!
Features
6 WS2812 2020 RGB LEDs, bright and every color is an option
Easy handling
Only one additional GND-wire needed when connected to FETtec ESC
Low resistance
For use with 3-6S
2 FETtec Race Wire 6 can be combited on one arm
Configurable via FETtec Configurator / KISS GUI, Transmitter and OSD
Specifications
Weight: 1g
Dimension: 8mm x 35mm
User Manual
User Manual
Includes
1x FETtec Race Wire 6 3-6S RGB LEDs (2pc)
