Check out this bundle of BEAST motors from NewBeeDrone, where you can grab 4 motors for the price of 69.99 dollars. You get 4 NewBeeDrone Flow 2207 2050Kv brushless race motors with this bundled deal. These motors are perfect for 6S builds and those who want that MONSTER power with a clean metal polish aesthetic. Deck out any quad with these motors, as they fit all styles of quads!
Check out our vast brushless motors selection, and all our NewBeeDrone products!
Specifications
Input Voltage: 6S
Shaft Size: 5mm
Weight: 33.3g
Mounting Pattern: 16x16mm M3
Includes
1x NewBeeDrone Flow 2207 2050Kv Brushless Race Motor - Choose Your Version
1x Hardware Set
Dont toss your battery just because the balance leads got chewed up in your props!
Repair the balance leads on your 6S batteries!
Note: Please check the colors of the wires and their respective polarities before connecting to your device.
Check out the rest of our Tools & Building Supplies!
Features
For IMAX B6 or Battery test.
6 cell 22.2V Lipo battery balance charger plug.
For Vehicle Type: Multirotor, Airplane, Helicopter.
Specifications
Material: 26 AWG Silicon Wire
Diameter (OD): 1.5mm
Conductor: Tinned Copper
Insulation: Silicone Rubber
Length of wire: approx. 15cm / 5.9 inch
Diameter of Single Metal wire/Quantity: 0.08mm/30
Includes
10x 6S1P JST Connector Male Plug with Wire
10x 6S1P JST Connector Female Plug
The Aikon flight controller is a new generation flight controller and ESC combination specifically designed for cinewhoops and other high-current applications. We've packed all the greatest features into one seamless flight experience.
Check out our other AIO flight controllers and the rest of our Aikon gear!
Features
216mhz F7 processor
Independent FC and ESC PCBs for low noise
5 Software invertible hardware UARTS
Onboard OSD and BlackBox
Software-controlled VTX power switch (assigned to USER1 mode by default)
Connectors for DJI-HD and RC link
LED and buzzer outputs (LED pad doubles as PPM)
On-board high overhead voltage regulators rated up to 6S (50v peak to handle voltage spikes)
10v 1.5A voltage regulator for DJI HD system
3.3mm high current MOSFETs.
Specifications
Battery: 3-6S
Mounting Holes: 25.5x25.5mm
FC Firmware: Betaflight AIKONF7 Target
MCU: STM32F722
IMU: MPU6000
Barometer: DSP310
Blackbox: SPI 16MB
ESC Firmware: BLHeli_32
Constant Current: 45A
Burst Current: 55A
Current Sensor Scale: 200
Weight: 14.5g
Includes
1x Aikon F7 Mini 25x25 AIO Flight Controller w/ 45A 32bit ESC
The Aikon AK32 Pro II continues Aikon's pursuit of excellence! This ESC combines the latest forward-looking capabilities with top of the line reliability.
Make sure to check out our other ESCs and entire line of Aikon gear!
Specifications
Input Voltage: 2-6S
MCU: AT32F421
Max Continuous Current: 50A
Max Burst Current: 65A
Firmware: BLHeli32
Bootloader: Yes
Mounting Pattern: 20x20mm
Weight: 13.8g
Includes
1x Aikon AK32PRO II 32bit 50A 2-6S 20x20 4in1 ESC
This FC pairs seamlessly with any Aikon ESC. The F7 MCU will allow you to dial in your tune the way you want it and the DJI plug and play means it's ready to go with the Air Unit or Vista.
Check out all our 20x20 FCs, our DJI compatible gear section, and all our Aikon gear!
Features
216mhz F7 processor
5 Software invertable hardware UARTS
Onboard OSD and blackbox
Software controlled VTX power switch
LED outputs
Quick connection cable for 4-in-1 ESCs
On-board high overhead voltage regulators up to 6S (50v peak for voltage spikes)
10V/1.5A regulator for DJI HD system
DJI Quick Connect Port
Specifications
Input Voltage: 2-6s
Mount Hole: 20x20mm
Betaflight Target: AIKONF7
MCU: STM32F722RET6
IMU: BMI270
Blackbox SPI: 16MB
Weight: 8g
Includes
1x Aikon F7 Mini V3 HD 20x20 Flight Controller for DJI
Wiring Diagram
The G4 features Betaflight compatibility and is the first of its kind. It contains 4 35A AM32 ESCs, 6S max and the QF32MTF4AK8U7 on the AIO board, creating a more compact design. Two voltage regulators – a 5V and 10V, both rated for 2.5A – are included. The 10V one can power the VTX & DJI O3 Air Unit, while the 5V one can power the LEDs, peripherals, etc. The STM32G47X MCU, ICM-42688p gyro, 16MB Data Flash, DSP310 baro, 16 RGB LEDs, and plug solutions for digital video complete the package.
A new feature is the ultra-hydrophobic nano waterproof coating. This coating allows air to pass through while avoiding water, giving extra protection from moisture and other elements.
Important note: When trying to get the HD OSD working, it's required that both ground pins out of the DJI port are not soldered to the VTX.
Check out our other AIO flight controllers, as well as the rest of our Airbot selection!
Features
Superhydrophobic Nano Waterproof Coating
Onboard 16 RGB LEDs can be programmed
ESC has a F4 MCU, runs AM32 firmware, capable of 6S and is rated at 35Amps
10V BEC for DJI O3 Air Unit
Specifications
MCU: STM32G473, 512KB Flash
BEC: 5V 2.5A + 10V 2.5A
Blackbox: 128Mbit, 16MB
Gyro: ICM-42688
Barometer: DSP310
ESC: F4 MCU, run AM32 firmware, 6S 35Amps
OSD: AT7456
4x Uarts
1x 12C
Weight:10.4g
Mounting pattern：25.5x25.5mm
Connector Pinout:
SDA, SCL, DN, DP, GND, 5V, L-RX1, L-TX1 is for External USB/GPS Connector
TX2, GND, RX1, TX1, GND, 10V is for VTX Connector
Wiring Diagram
- Information was referenced from a review of the Airbot Fenix G4 AIO board brought to you by VitroidFPV.
in AKK's newest VTX which has built-in DVR, Smart Audio, up to 6s (7 - 26v) direct Lipo input, adjustable power output (25, 200, 600 & 1000 mW) w/ pit mode, and a 5v cam power output.
Check out the rest of our selection of VTX's!
Specifications
Brand name: AKK
Item name: Infinite DVR VTX
Input voltage: 7V to 26V
Extra features: Smart audio DVR
Power supply: 5V output for camera
Output power: 25/200/600mW/1000mW
Antenna connector: MMCX
Cable connector: Solder pads
Records Video Size: VGA (640*480)
Max Support TF Card: 32G
Dimension: 36x36mm, 30.5 stackable hole
Weight: 8.8g (excluding antenna)
Features
Support Smart audio
25/200/600/1000mW power switchable
One button frequency and power setupOSD configuration using smart audio
7-26V input with 5V output for camera
With MIC
Notice: 5645/5925/5945 (E4/E7/E8) are not available due to FCC regulation. Selecting 5645/5925/5945 (E4/E7/E8) will be invalid action.
Note: 37 channels are all above 5650 and below 5925MHz, which are legal to use in the USA with an amateur radio license.
This equipment is being sold under FCC’s amateur radio rules.
Operators must require amateur radio license to operator legally in
the US. Use of amateur equipment without a license or use of
equipment on restricted frequencies could subject the operator to
significant fines by the FCC.By purchasing this equipment, the user is
agreeing that they understand these responsibilities and will operate
the equipment legally. More information related to ARL, please go to
http://www.arrl.org/getting-licensed.Pacakge Included:
1x VTX
1x pigtail
1x cable
FPV REGULATORY NOTICE
The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. RDQ cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1750
Input Voltage: 4-6S
Motor Height: 16.5mm
Stator Dimensions: Φ22x7mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 28.1g
Includes
1x AMAX Performante A-Bell 2207 1750Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1750
Input Voltage: 4-6S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 1750Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1950
Input Voltage: 4-6S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 1950Kv Motor
All batteries must be shipped by a ground shipping method.
6S 4000mAh battery perfect for long-range wings & quads.
Check out the rest of our Auline products and our whole battery collection!
Features
XT60 Connector
Great for wings and efficient quads
Max 35A output
Specifications
Continuous Discharge Current: 35A
Dimensions: 75x65x45mm
Weight: About 420.5g
Capacity: 4000mAh
Type: Li-ion Battery
Cell: 21700 40T
Cells: 6S1P 6S
Voltage: 22.2V
Brand: Auline
Plug: XT60
Includes
1x Auline 22.2V 6S 21700 4000mAh 35A Li-Ion Battery - XT60
All batteries must be shipped by a ground shipping method.
6S 3000mAh battery perfect for long-range wings & quads.
Check out the rest of our Auline products and our whole battery collection!
Features
XT60 Connector
High-Quality Sony VTC6 cells
Great for wings and efficient quads
Max 30A output
Specifications
Capacity: 3000mAh
Voltage: 22.2V
Connector: XT60
C-Rate: 10C/ 30A Max
Recommended Charge Rate: 1C / 3A
Weight: 297g
Includes
1x Au line 22.2V 6S 3000mAh 10C Li-Ion Battery - XT60
All batteries must be shipped by a ground shipping method.
These Aulines are powerful Lipo batteries that are best suited for long-range and cruising flights! This 6S battery is equipped with a 3300mAh capacity, 22.2V, and comes with an XT-60 connector.
Check out the rest of our Auline products and our whole battery collection!
Features
XT60 Connector
High C rating
Tons of MAH
Lipo Battery
Specifications
Capacity: 3300mAh
Voltage: 22.2V
Connector: XT60
C-Rate: 45
Recommended Charge Rate: 1C
Weight: 430g
Dimensions: 135x42x35
Includes
1x Auline 22.2V 6S 3300mAh 45C Lipo Battery - XT60
All batteries must be shipped by a ground shipping method.
The EX line of batteries by Auline are powerful Lipo batteries that are best suited for racing whoops or 5" freestyle quadcopters! This 6S battery is equipped with a 1050mAh capacity, 22.2V, and comes with an XT-60 connector.
Check out the rest of our Auline products and our whole battery collection!
Features
XT60 Connector
High C rating
Specifications
Capacity: 1050mAh
Voltage: 22.2V
Connector: XT60
C-Rate: 120
Recommended Charge Rate: 1C
Weight: 193.6g
Dimensions: 69x38x36
Includes
1x Auline EX 22.2V 6S 1050mAh 120C Lipo Battery - XT60
All batteries must be shipped by a ground shipping method.
The Auline 22.2V 6S 1350 mAh 120C LiHV Battery is the perfect solution for your 5" quads. The SR series provides reliable, efficient power with a long flight times. Including an XT60 connector ensures a secure connection, delivering reliable and consistent power.
Check out all our 6S batteries and the rest of our Auline products
Specifications
Brand: Auline SR
Capacity: 1350mAh
Voltage: 22.2V
C-Rate: 120C
Weight: 219g
Charging: 1C Max
Assemble: 6S1P
Plug: XT60
Noted: SuperLight
Includes
1x Auline SR 22.2V 6S 1350mAh 120C LiPo Battery - XT60
Premium performance. That’s been the focus of AxisFlying since we started a year ago. The AF series, and now the BB series. We pushed the envelope of the tried-and-true FPV formula. Now we’ll be doing it again…Introducing AE series, by AxisFlying. Great performance, high quality, and the high standards that we hold all of our products to. The AE series is the perfect compromise of price and performance. Now, we’re fully aware of the stigma surrounding ‘budget’ motors. Can’t compromise on price without compromising on performance, right? Wrong. Our engineers took the same principles we take to all our motor designs, and pulled back as much cost as possible – all while keeping the quality and performance. We truly believe that this is the alternative to the high-end motors… whilst being under $16.
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 6S
Kv Rating: 1800Kv
Stator Size: 23x6mm
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 5mm
Max. Power (60s): 901W
Internal Resistance: 60.7mΩ
Peak Current: 40.6A
Motor Dimensions: ɸ27.9x32.7mm
Weight (Incl. Cable): 31.5g
Mounting Pattern: 16x16mm
Includes
1x Axis Flying AE2306.5 1800Kv Motor
Premium performance. That’s been the focus of AxisFlying since we started a year ago. The AF series, and now the BB series. We pushed the envelope of the tried-and-true FPV formula. Now we’ll be doing it again…Introducing AE series, by AxisFlying. Great performance, high quality, and the high standards that we hold all of our products to. The AE series is the perfect compromise of price and performance. Now, we’re fully aware of the stigma surrounding ‘budget’ motors. Can’t compromise on price without compromising on performance, right? Wrong. Our engineers took the same principles we take to all our motor designs, and pulled back as much cost as possible – all while keeping the quality and performance. We truly believe that this is the alternative to the high-end motors… whilst being under $16.
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 6S
Kv Rating: 1960Kv
Stator Size: 23x6mm
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 5mm
Max. Power (60s): 901W
Internal Resistance: 60.7mΩ
Peak Current: 40.6A
Motor Dimensions: ɸ27.9x32.7mm
Weight (Incl. Cable): 31.5g
Mounting Pattern: 16x16mm
Includes
1x Axis Flying AE2306.5 1800Kv Motor
The Axis Flying AE2207 1850Kv Motor brings the performance you've come to expect from their most premium motors, now in an economical package. These motors come at a fraction of the price compared to many motors today but still outperform even the best of them!
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 6S
Kv Rating: 1850Kv
Stator Size: 22x7mm
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 5mm
Max. Power (60s): 797W
Internal Resistance: 75mΩ
Peak Current: 33A
Motor Dimensions: ɸ27.2x33.3mm
Weight (Incl. Cable): 31.4g
Includes
1x Axis Flying AE2207 1850Kv Motor
Axis Flying's new AE2207 brings the performance you've come to expect from their most premium motors, now in an economical package. These motors come at a fraction of the price compared to many motors today but still outperform even the best of them!
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 6S
Kv Rating: 1960Kv
Stator Size: 22x7mm
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 5mm
Max. Power (60s): 921W
Internal Resistance: 60.5mΩ
Peak Current: 38A
Motor Dimensions: ɸ27.2x33.3mm
Weight (Incl. Cable): 32.1g
Includes
1x Axis Flying AE2207 1960Kv Motor
Another great addition to the AxisFlying lineup, with 3-6S input, BLHeli32 firmware, and up to 75A burst, the Argus 65A 4in1 ESC will handle even the most amp-hungry motors.
Check out all our 30x30 ESCs and all our Axis Flying Products!
Specifications
Continuous Current: 65A
Burst Current: 75A
Input Voltage: 3-6S
ESC Target: BLHeli_32 (ST_G0_04)
Current Proportion value: Scale=400
PWM Frequency Range: 16-96khz
Telemetry: Supported
Ammeter: Supported
BEC: No
Installation holes: 30.5x30.5mm
Dimensions: 48.6x44x6.3mm
Weight: 16.2g
Includes
1x AxisFlying Argus 32bit 65A 3-6S 30x30 4in1 ESC
1x Wiring Set
The latest from AxisFlying, the Argus F7 is a powerhouse of a chip. It comes in two versions, regular and PRO which has a CNC heat dissipation aluminum cover. It has a high-performance F722 chip, onboard barometer, OSD and Black Box. And it can support up to 8 motors! This chip comes packed with power. Pair it with the Argus 65A ESC for ease of installation; a convenient plug-and-play feature. And it supports the new DJI O3 Air Unit! AxisFlying has got you covered!
Check out all our 30x30 Flight Controllers, and all our Axis Flying Products!
Features
High-quality and large-size MOSFETs are selected, with low internal resistance and low heat generation.
No welding, more peace of mind. With this FC, HD Air unit, analog camera, GPS, and other common peripherals all support direct plug-in
Integrated dual BEC, support DJI O3 Air Unit direct connection
The FC supports up to 8 motor outputs, easily build your X8 drone
Quickly check the working status of the FC by turning on and off the corresponding status indicator light
Specifications
MCU: STM32F722RET6
Gyro: BMI270
Barometer: Yes
OSD: Yes
BEC: 9V/2A, 5V/2A
UART Ports: 6
Black Box: 16MB onboard
Number of supported motors: 8
Firmware Name: AXISFLYINGF7
Input Voltage: 3-6S LiPo (12-50V Max)
Installation Holes: 30.5x30.5mm M3
Includes
1x AxisFlying Argus F7 3-6S 30x30 Flight Controller
1x Assorted Connector wires
The latest from AxisFlying, the Argus F7 is a powerhouse of a chip. It comes in two versions, regular and PRO which has a CNC heat dissipation aluminum cover. It has a high-performance F722 chip, an onboard barometer, OSD and Black Box. And it can support up to 8 motors! This chip comes packed with power. Pair it with the Argus 65A ESC for ease of installation; a convenient plug-and-play feature. And it supports the new DJI O3 Air Unit! AxisFlying has got you covered!
Check out all our 30x30 Flight Controllers, and all our Axis Flying Products!
Features
High-quality and large-size MOSFETs are selected, with low internal resistance and low heat generation.
No welding, more peace of mind. With this FC, HD Air unit, analog camera, GPS, and other common peripherals all support direct plug-in
Integrated dual BEC, support DJI O3 Air Unit direct connection
The FC supports up to 8 motor outputs, easily build your X8 drone
Quickly check the working status of the FC by turning on and off the corresponding status indicator light
Specifications
MCU: STM32F722RET6
Gyro: BMI270
Barometer: Yes
OSD: Yes
BEC: 9V/2A, 5V/2A
UART Ports: 6
Black Box: 16MB onboard
Number of supported motors: 8
Firmware Name: AXISFLYINGF7
Input Voltage: 3-6S LiPo (12-50V Max)
Installation Holes: 30.5x30.5mm M3
Includes
1x AxisFlying Argus F7 3-6S 30x30 Flight Controller
1x Assorted Connector wires
The Plug and Play Argus is AxisFlying electronic series that includes ESC, FC, and stack. Argus PRO series adopt a full aluminum cover wrapped that can get IP54 to protect PCB. Argus series is PCB electronic only. There are 2 kinds of ESC 55A and 65A. The FC is F722 which can support X8.
Check out all our 30x30 FC Stacks, and all our Axis Flying Products!
Specifications
Argus F722 Flight Controller
MCU: STM32F722RET6
Gyro: BMI270
Barometer: Yes
OSD: Yes
BEC: 9V/2A, 5V/2A
UART Ports: 6
Black Box: 16MB onboard
Number of supported motors: 8
Firmware Name: AXISFLYINGF7PRO
Input Voltage: 3-6S LiPo
Installation Holes: 30.5x30.5mm M3
32bit 4in1 ESC
Continuous Current: 55A
Burst Current: 65A
Input Voltage: 3-6S
ESC Target: BLHeli_32 (ST_G0_04)
Current Proportion value: Scale=400
PWM Frequency Range: 16-96khz
Telemetry: Supported
Ammeter: Supported
BEC: No
Installation holes: 30.5x30.5mm
Dimensions: 48.6x44x6.3mm
Weight: 16.2g
Includes
1x AxisFlying Argus F722 3-6S 30x30 Stack/Combo (F7 FC / 32bit 55A 4in1 ESC)
1x Wiring Set
Experience the efficient and reliable AIO solution of the AxisFlying Argus F722 F7 for your Whoop/Toothpick builds, complete with 40A 8Bit 4in1 ESC and pink aluminum shell. CNC heat sink on both sides ensures better cooling and longer service life.
Browse the rest of our Whoop AIO Boards and all our Axis Flying Products!
Feature
Every AIO goes through 800 full-throttle takeoff and landing tests before leaving the factory. High-quality circuit technology and aluminum shell casing will ensure their service life.
Stylish CNC heat sink on both sides. Better cooling and increased lifespan.
The big concern of every pilot - desyncs - will be solved by the Argus F7 AIO.
Perfectly match with 20/21 motors.
PNP HD VTX interface
Specifications
FC target: AXIS ARGUS F7 AIO
DJI O3 dedicated plug: Supported
Barometer: Supported
Beeper: Supported
Sized: 36x36x7.2mm
MCU: STM32F722RET6
Gyro: BMI270
Continuous Current: 40A
Peak Current: 50A
Uart: 5
OSD: Supported
LED: Supported
Input Voltage: 4-6S
Mounting: 25.5x25.5mm/26.5x26.5mm M3
Includes
1x Axisflying Argus F722 F7 Whoop/Toothpick AIO Flight Controller w/ 40A 8Bit 4in1 ESC & Pink Aluminum Shell
The lightweight Argus Mini is specially designed for small size FPV drone, reducing the weight of the whole FPV to a greater extent while providing stable and excellent control. This flight controller is small and compact while boasting community favorite MPU6000 gyro for the best performance.
Check out all our 20x20 FCs and all our Axis Flying Products!
Specifications
MCU: STM32F722RET6
FC target: AXIS FLYING F7 PRO
Mounting Holes: 20x20mm M2/M3
FC: Axisflying F7 PRO
Gyro: MPU6000
BEC: 5V 3A
Blackbox: 16MB
Weight: 5g
UART: 1-5
OSD: Supported
Barometer: Supported
Size: 28.5x27x6.2mm
Includes
1x AxisFlying Argus Mini F7 4-6S 20x20 Flight Controller - MPU6000
New from AxisFlying, the Argus PRO 32bit 65A ESC. The Argus PRO series uses a wrapped all-aluminum cover that can get IP54 to protect the PCB. The Argus series is PCB electronic only. This is a premium-built ESC from AxisFlying, fully capable of pushing 6S!
Check out all our 30x30 ESCs and all our Axis Flying Products!
Features
Dustproof and waterproof IP54, with splashproof function, it is forbidden to put it into water or use it underwater!
CNC Full aluminum cover wrapped, enlarging the radiating surface, rapid heat dissipation, more stable work
High-quality and large-size MOSFETs are selected, with low internal resistance and low heat generation, plus CNC heat dissipation aluminum cover, Even if the throttle is used for a long time, it is not afraid of overheating, which brings more stable power performance.
Specifications
Continuous Current: 65A
BLHeli_32 32bit
Burst Current: 75A
Size: 30.5x30.5mm M3
BEC: No
Weight: 32g
Input Voltage: 3-6S LiPo (12-30V Max)
ESC Target: BLHeli_32 (ST_G0_04)
Current Proportion Value: Scale = 400
PMW Frequency Range: 16-96khz
Telemetry: Supported
Ammeter: Supported
BEC: No
Installation Holes 30.5x30.5mm
Size: 48.6x46.6x8.7mm
Weight: 32g
Includes
1x AxisFlying Argus PRO 32bit 65A 3-6S 30x30 4in1 ESC
The Plug and Play Argus is AxisFlying electronic series that includes ESC, FC, and stack. Argus PRO series adopt a full aluminum cover wrapped that can get IP54 to protect PCB. Argus series is PCB electronic only. The FC is F722 which can support X8. If you want the best and for your build to look futuristic, this is the stack for you!
Check out all our 30x30 FC Stacks, and all our Axis Flying Products!
Specification
Argus PRO F722 Flight Controller
MCU: STM32F722RET6
Gyro: BMI270
Barometer: Yes
OSD: Yes
BEC: 9V/2A, 5V/2A
UART Ports: 6
Black Box: 16MB onboard
Number of supported motors: 8
Firmware Name: AXISFLYINGF7
Input Voltage: 3-6S LiPo
Installation Holes: 30.5x30.5mm M3
32bit 4in1 ESC
Continuous Current: 65A
BLHeli_32 32bit
Burst Current: 75A
Size: 30.5x30.5mm M3
BEC: No
Weight: 32g
Input Voltage: 3-6S LiPo (12-30V Max)
ESC Target: BLHeli_32 (ST_G0_04)
Current Proportion Value: Scale = 400
PMW Frequency Range: 16-96khz
Telemetry: Supported
Ammeter: Supported
BEC: No
Installation Holes 30.5x30.5mm
Size: 48.6x46.6x8.7mm
Weight: 32g
Includes
1x AxisFlying Argus PRO F722 3-6S 30x30 Stack/Combo (F7 FC / 32bit 65A 4in1 ESC)
1x Wiring Set
Blackbird V3 2207 1975Kv Motor is the perfect choice for powerful and efficient racing and freestyling. This motor was developed in collaboration with renowned FPV pilot Damien Gans, better known as "Black Bird". This motor features BST bearing shield tech which protects from dust and water, extending bearing smoothness and life. Get more thrust and say goodbye to crushed bearings. Behind the classy look of the black and gold there is monster power, perfect for your next 6S quad. Get ready to take your experience to the next level.
Check out our vast motor selection and all our Axis Flying Products!
Features
Bearing Shield Technology
An IP53 rating dustproof and waterproof bearing placement design.
BST protects from environmental elements and prolongs the smoothness and lifespan of the bearing. Increased thrust efficiency and say goodbye to crush motor bearings
Specifications
Configuration: 12N14P / N52H arc magnet
Motor stator size: 2207.3
Kv Rating: 1975Kv
Input Voltage: 6S
Motor mounting hole size: 16mmx16mm M3
Motor cables: AWG 20#, 150MM
Motor dimensions (Dia *Len): Φ27.5 x 33.4MM / M5 shaft
Weight: 32.6g
Max.Power: 1070W
Peak Current: 44.7
Internal Resistance: 56m Ω
Includes
1x AxisFlying Blackbird V3 2207 1975Kv Motor
1x Hardware Kit
Premium performance. That’s been the focus of AxisFlying since they started a year ago. These amazing new cinewhoop motors offer exceptional power and can keep the heaviest of HD cams in the air!
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 6S
Kv Rating: 2910Kv
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 1.5mm T
Weight (Incl. Cable): 22g
Mounting Pattern: 12x12mm M2
Includes
1x Axis Flying C204 2004 2910Kv Motor
Premium performance. That’s been the focus of AxisFlying since we started a year ago. These amazing new cinewhoop motors offer exceptional power and can keep the heaviest of HD cams in the air!
Check out our vast motor selection and all our Axis Flying Products!
Specifications
Input Voltage: 6S
Kv Rating: 1900Kv
Configuration: 12N14P
Wire: 20#AWG 150mm length
Shaft Diameter: 5mm
Weight (Incl. Cable): 22g
Mounting Pattern: 12x12mm M2
Includes
1x AxisFlying C224 2204.5 1900Kv Motor
Axis Flying has entered the world of Express LRS products with their THOR module. Typical of Axis, this module is built to satisfy even the most demanding of pilots. This module can sustain high output power over long periods of time making this the ideal setup for range or penetration!Check out all our ExpressLRS compatible gear, and all our Axis Flying Products!
Features
Built in color display W/ motion detection and Joystick control
Wi-Fi update capable
Backpack Function
Automatic or Active cooling
Specifications
Input voltage: 5V-12V
XT30 port: 7V-21V, DOES NOT support 6S or above battery voltage
Packet Refresh Rate: 50Hz/150Hz/250Hz/500Hz
RF Output Power: 25mW/50mW/100mW/250mW/500mW/1000mW
Frequency Band: 2.4GHz ISM
USB Port: Type-C
Dimensions: 87x55x15mm
Storage Box Size: 29x29x15.5mm
Weight: 105g
Includes
1x Axis Flying THOR Pro ELRS 2.4GHz Module
New V2 comes with a tactile power button, 6S support and a cable management kit! The plug and play Digidapter from British Drone Industries is the cleanest way to add analog FPV capabilities to your DJI Goggles. The injection molded face plate keeps your goggles looking sharp, and the included cables mean soldering is purely optional.
Check out all our FPV receiver modules and our DJI compatible gear!
Features
Short delay tactile power button for analog module
Compatible with existing modules: The Digidapter is compatible with existing analog modules. Featuring a standard 9 pin header for use with the TBS Fusion, Foxeer Wildfire, Rapid Fire, True D-X, Eachine Pro58, and more..
Plug & Play No Solder Solution: Installation takes less than a minute, and mounts quickly and easily to the front of your DJI Digital FPV Goggles. Including optional solder points for a cable free solution.
New cable management set included!
Specifications
Maximum Input Voltage: 28 Volts DC
Minimum Input Voltage: 7.4 Volts DC
Nominal Output Voltage: 5 Volts DC
Maximum Module Supply Current: 1 Amp
Rated Continuous Power: 5 Watts
Ports:
5.5mm x 2.1mm DC In 7.4v-26v (2s-6s)
4 pole 3.5mm video/audio out
9 pin RF module receiver header
Cables:
5.5mm x 2.1mm Male to Dual 5.5mm x 2.1mm Female DC Jack Splitter
4 Pole Gold Plated 3.5mm Male to 3.5mm Male Video Cable
Material/Color: Matte Black, Injection Molded, Acrylonitrile Butadiene Styrene
Dimensions: 158x74x40mm (6.25x3x1.6 inches)
Weight: 34g
Includes
1x Digidapter V2 faceplate
1x Analog video cable
1x Analog video/audio splitter for audio out
1x Dual DC/DC male to single DC female split cable
1x Allen key
2x 12mm cap head bolts
1x Cable strain relief clip
2x Cable clips
F722 2-6S AIO 35A FC is a very reliable FC that is made to meet your advanced FPV needs. Comes with an F722 chip and a BLHeli_32 ESC, this board provides a better performance capability and higher calculation speed, which brings pilots a more stable and smoother flight. What's more, F722 AIO FC has specially added a 6-pin connector for DJI Digital VTX, just plug & play, less solder work needed, super easy to install. It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery.
Check out all our whoop flight controllers, and all our BetaFPV gear!
A very in-depth video on the BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller.
Features
Built-in STM32F722RET6 CPU, F722 FC is more powerful than F4. It features a fast processing speed and stable performance, providing reliable and smooth flight for 4"-5" drones.
F722 AIO 35A FC has specially added a 6-pin connector for HD Digital VTX, just plug & play, less solder work needed, perfect for the pilots who enjoy the HD Digital VTX system.
6 full UARTs are available on this board. With plenty of UARTS, Pilots could have more options for external parts like VTX, GPS, Receiver, and other components.
It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery, and gives the drone a more robust flight performance.
With the 6S battery and this F722 35A AIO FC, the drone will break through the limit of the power of the toothpick drone, exploring more possibilities in 4-5'' drones.
The new BLHeli_32 ESC version is built-in a 16MB flash memory chip dedicated to Blackbox logging, which is an extremely powerful tool for tuning and troubleshooting an FPV drone. It has a faster processing speed and up to 128k PWM frequency, providing a more stable and smoother flight for pilots.
V2 with BLHeli_32 ESC
V1 with BLHeli_S ESC
PWM Frequency
24k-128k
24k-96k
ESC Firmware
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
Blackbox
16MB
Not included
Weight
9.00g
7.06g
Board Thickness
1.6mm
1.4mm
BLHeli_32 ESC Firmware
The F722 35A AIO FC has two boards with different ESC versions for choice. The V2 board uses AT32F421G8U7 MCU, a 32-bit ESC chip, with BLHeli_32 ESC firmware. This firmware supports up to 128k PWM frequency, featuring faster processing speed and unlocking more functions for the flight.
BLHeli_32 ESC
BLHeli_S ESC
MCU
AT32F421G8U7
EFM8BB21F16G-C
Firmware Version
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
PWM Frequency
24k-128k
24k-96k
Bidirectional DSHOT
Support
Support
Signal Support
PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Know More About ICM42688 Gyro
The F722 FC ICM42688 version has the same solder pad and layout as BMI270 except for the gyro chip. Besides, you can also find the difference in Betaflight settings.
The ICM42688 gyro supports 8.00 kHz gyro update frequency compared with the BMI270 gyro which supports 3.20 kHz. When using a 6S battery, the ICM42688 gyro has a good performance.
The degree between ICM42688 and BMI270 gyro is different. When configuring F722 FC ICM42688 version, the gyro degree should be set to CW270°.
Diagram for F722 35A AIO FC
The below picture is the top front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
The below picture is the bottom front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
There are 2 LEDs on the bottom of the board to indicate the status, including the FC LED (Blue) and FC Power LED (Red). The LED status for V1 and V2 boards are the same.
LED
Status
Description
FC LED (Blue)
Solid
Armed
FC LED (Blue)
Extinguished
Disarmed
Power LED (Red)
Solid
Power on
How to Connect the External RX&VTX
To connect the external RX&VTX, please refer to the below diagram. F722 35A AIO V1 and V2 boards have the same soldering pad and connecting ports.
Specifications
Flight Controller
Item: F722 35A AIO Brushless Flight Controller
Weight: 9.00g (BLHeli_32)
CPU: STM32F722RET6
Six-Axis: ICM42688
Mounting hole size: 26mmx26mm
Firmware version: betaflight_4.3.0_STM32F7X2
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Support programmable LED like WS2812 etc
Built-in current sensor
Blackbox: 16MB (V2 with BLHeli_32 ESC included)
ESC
Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/TBS Crossfire Receiver (requires external connection)
Input voltage: 2S-6S Lipo
Continuous current: 35A
Peak current: 40A
ESC firmware: BETAFPV_35A_V2_BLHeli_32_Multi_32_9 (BLHeli_32)
Indicators: Power indicator (Red) / FC indicator (Blue)
Capacitance: CS|5*10*13mm|470μF|35V
Connector: 80mm 14AWG silicone cable with XT60
Recommended motors: 14XX series, 15XX series, 16XX series, 18XX series, 20XX series
Includes
1x BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller (w/ 35A 32Bit 4in1 ESC) - ICM42688
This big beautiful motor is the Avenger 2806.5 and it is here to spin your 6-8" props and spin them right. Super wide stator for torque all day, and massive bearings to match. The Brother hobby quality you trust!
Check out our entire motor section and all our Brotherhobby section.
Features
Titanium Alloy Hollow Shaft
AL7075 Bell and Base
N52H Arc Magnets
0.2mm Kawasaki Silicon Steel Stator
Specifications
KV: 1300KV
No.of Cells(Lipo): 4-6S
Configuration: 12N14P
Prop Adapter Shaft Thread: M5
Bolt Pattern: M3 (19X19mm)
Weight: 41g with short SR wires
Wire AWG: 18AWG 20cm length
Includes
1x Avenger 2806.5 Motor
1x Motor Nut
1x Bag of Screws
The BrotherHobby Avenger 2507 V2 1850KV 4-6S Motor is designed to give the power and efficiency needed for Long Range FPV!
V2 comes with a new propeller grip on the top of the bell. The color scheme has also changed to all black.
We carry these motors in 1500, 1700 and 1850Kv.
Check out our entire motor section and all our Brotherhobby section.
Specifications
KV: 1850
Configuration: 12N14P
No.of Cells(LiPo): 4-6S
Rotor: N52H arc magnets
Stator: 0.15mm Nippon Steel silicon steel
Shaft: Titanium Alloy hollow shaft
Bearings:Japanese NMB 9x 4 x 4mm
Wire AWG: 18AWG 16cm length
Bell cap: Al 7075
Base casing: Al 7075
Prop Adapter Shaft Thread: M5
Bolt Pattern: M3 (16X16mm)
Weight: 38G (with short wire)
Includes
1x Avenger 2507 V2 1850Kv Motor
1x Motor Nut
4x Motor Screws
Tests & Videos
Manufacturer Testing:3rd Party Testing:
EngineerX Thrust Table
The BrotherHobby Avenger 2507 V2 1850KV 4-6S Motor is designed to give the power and efficiency needed for Long Range FPV!
V2 comes with a new propeller grip on the top of the bell. The color scheme has also changed to all black.
We carry these motors in 1500, 1700 and 1850Kv.
Check out our entire motor section and all our Brotherhobby section.
Specifications
KV: 1850
Configuration: 12N14P
No.of Cells(LiPo): 4-6S
Rotor: N52H arc magnets
Stator: 0.15mm Nippon Steel silicon steel
Shaft: Titanium Alloy hollow shaft
Bearings:Japanese NMB 9x 4 x 4mm
Wire AWG: 18AWG 16cm length
Bell cap: Al 7075
Base casing: Al 7075
Prop Adapter Shaft Thread: M5
Bolt Pattern: M3 (16X16mm)
Weight: 38G (with short wire)
Includes
1x Avenger 2507 V2 1850Kv Motor
1x Motor Nut
4x Motor Screws
Tests & Videos
Manufacturer Testing:3rd Party Testing:
EngineerX Thrust Table
These big boys are ready to to rock your 8"+ props! This KV is ideal for 5-6S macro builds, see the "Test Data" tab for more info.
Check out our huge selection of motors and all our Brotherhobby gear!
Features
Incredibly powerful, yet smooth running
Extremely durable due to quality components
Lightweight (for their size!)
Specifications
KV: 1115KV
Input Voltage: 5-8S
Configuration: 12N14P
Bell cap: Al 7075
Base casing: Al 7075
Stator: 0.2mm Kawasaki silicon steel
Bearings: Japanese NMB 12X6X4
Rotor: N52H arc magnets
Shaft: Titanium Alloy hollow shaft
Prop Adapter Shaft Thread: M5
Wire AWG: 18AWG 25cm length
Bolt Pattern: M3 (19X19mm)
Weight: 76.5g with 25cm SR wires
Includes
1x BrotherHobby Avenger V3 2812 1115Kv Motor
The BrotherHobby GOM 2207.5 Motor is your next big step in FPV Racing! The GOM is a high-quality motor made with Japanese NMB bearings for smooth, free, and quiet flying. The high-quality single piece bell increases the overall durability of the motor and prevents the motor from getting damaged during a crash.
Be sure to check out our entire motor section and our Brotherhobby section for other great motors and products!
Specifications
Kv: 1920Kv
Configuration: 12N14P
Input Voltage (LiPo): 4-6S
Rotor: N52H arc magnets
Copper wire: 260℃ Military grade
Stator: 0.15mm Nippon Steel silicon steel
Shaft: 0.15mm Nippon Steel silicon steel
Bearings: Japanese NMB 9x4x4mm
Wire AWG: 20AWG 16cm length
Bell cap: Al 7075
Base casing: Al 7075
Prop Adapter Shaft Thread: M5
Bolt Pattern: M3 (16X16mm)
Includes
1 x BrotherHobby GOM 2207.5 1920Kv Motor
The BrotherHobby GOM 2207.5 Motor is your next big step in FPV Racing! The GOM is a high-quality motor made with Japanese NMB bearings for smooth, free, and quiet flying. The high-quality single-piece bell increases the overall durability of the motor and prevents the motor from getting damaged during a crash.
Be sure to check out our entire motor section and our Brotherhobby section for other great motors and products!
Specifications
Kv: 2500Kv
Configuration: 12N14P
Input Voltage (LiPo): 4-6S
Rotor: N52H arc magnets
Copper wire: 260℃ Military grade
Stator: 0.15mm Nippon Steel silicon steel
Shaft: 0.15mm Nippon Steel silicon steel
Bearings: Japanese NMB 9x4x4mm
Wire AWG: 20AWG 16cm length
Bell cap: Al 7075
Base casing: Al 7075
Prop Adapter Shaft Thread: M5
Bolt Pattern: M3 (16X16mm)
Includes
1 x BrotherHobby GOM 2207.5 2500Kv Motor
The BrotherHobby LPD 2306.5 Motor is your next big step in FPV Racing! The LPD is a high-quality motor made with Japanese NMB bearings for smooth, free, and quiet flying. The high-quality single-piece bell increases the overall durability of the motor and prevents the motor from getting damaged during a crash.
Be sure to check out our entire motor section and our Brotherhobby section for other great motors and products!
Specifications
Kv: 2000Kv
Configuration: 12N14P
No. of Cells(Lipo): 4-6S
Rotor: N52H arc magnets
Copper wire: 260 ℃ Military grade
Stator: 0.15mm Nippon Steel silicon steel
Shaft: 0.15mm Nippon Steel silicon steel
Bearings: Japanese NMB 9x4x4mm
Wire AWG: 20AWG 16cm length
Bell cap: Al 7075
Base casing: Al 7075
Prop Adapter Shaft Thread: M5
Bolt Pattern: M3 (16X16mm)
Includes
1 x BrotherHobby LPD 2306.5 2000Kv Motor
Experience powerful performance with the BrotherHobby R3.5 2205 2140Kv brushless motor, ideal for cinewhoops with 3.5" prop. Enjoy low throttle, high thrust, and extended flight times for superior power with every flight. Take your aircraft to the next level with the reliable quality and precision from BrotherHobby motors.
Check out our huge selection of motors and all our BrotherHobby gear!
Specifications
KV: 2140
Configuration: 12N14P
Maximum Thrust: 811g
Motor Weight: 27.18g
ESC: 6S 35A
Shaft: Titanium Alloy hollow shaft
Magnet: N52H arc magnets
Wire AWG: 20AWG
Bearings: Japanese NSK 8X3X4
Base casing: AI 7075
Bell cap: AI 7075
Bolt Pattern: M2(12X12mm)
Weight: 16cm SR wires
Includes
1x BrotherHobby R3.5 2205 2140Kv Brushless Motor
These motors are designed for sub 250g racing builds with T-Mount props, they work great as micro long-range motors as well.
Available in multiple KV options.
Check out our huge selection of motors and all our BrotherHobby gear!
Specifications
KV: 3150
Configuration: 12N14P
No.of Cells(Lipo): 4-6S
Rotor: N52H arc magnets
Stator: 0.15mm Nippon silicon steel
Shaft: SUS 420
Bearings: NMB 7x3x3
Wire AWG: 24 AWG wire 16cm length
Bell cap: 7075 Al
Base casing: 7075 Al
Prop Adapter Shaft Thread: M1.5
Bolt Pattern: M2 12X12
Weight: 14.9g w/ short wire
Includes
1x BrotherHobby TC 2004 3150Kv Micro Motor
This stunning motor distracts from its real power using its great design. However, underneath this stunning visage lies a powerful motor ready to roar. The Brother Hobby VS2007 motors are a perfect blend of form and function.
Check out our other 2207 motors, and all our BrotherHobby selection!
Specifications
Kv: 2400Kv
Input Voltage: 4-6S LiPo
Configuration: 12N14P
Stator Dimensions: Φ22mm x 07mm
Shaft Diameter: 5mm
Mounting Pattern: Φ16mm
Wire Dimensions: 20AWG x 160mm
Weight (w/ wires): 32.5g
Includes
1x BrotherHobby VS 2207 2400Kv Motor
The Avenger 1507 line has been reshaped into the new VY series of motors! A great choice for cinewhoop builds, these are available in 3100Kv for 6S and 4150Kv for 4S.Check out the rest of our Micro Motors and all our Brotherhobby gear!
Specifications
KV: 4150KV
Configuration: 12N14P
Wire AWG: 24AWG
Magnet: N52H arc magnets
Copper wire: Missile Grade Material( resistant to 260℃）
No.of Cells(Lipo): 4-6S
Base casing: Al 7075
Bell cap: Al 7075
Bearings: Japanese NSK 5x2x2.5 mm
Stator: 0.15mm Nippon stell silicon steel
Bolt Pattern: M2 (12mm 12 mm)
Weight: 16.3g with 16cm long wires
Includes
1x Brother Hobby VY 1507 4150Kv Micro Motor
The Caddx FPV Walnut Action Camera features 4k/60fps picture quality, IP64 waterproof rating, and gyroflow for stabilization This impact-resistant camera weighs only 60g and has optional ND8 and ND16 Filters.Check out all our HD Action Cams and our Caddx Selection!
Features
One-Key Startup
4K/60fps high-definition picture quality with 100mbps bit rate
Screw On ND8 and ND16 Filters
The fuselage comes with a battery
A hard shell with a soft rubber interior design makes it impact-resistant
IP64 Waterproof Rating
Magnetic Charging
63.4g in Weight
Gyroflow can be used for post stabilization
Specifications
Input Voltage: Type-C, 2S-6S BEC, Magnet
Video Resolutions:4K/60fps,4K/30fps(4/3),2.7K/60fps,2.7K/30fps(4/3), 1440P/60fps,1080p/120fps.
SD card: Max 256G
Video Format: MP4
Video Encode: H.264/H.265
Video Max Bitrate: 100Mbps
Wifi: 5GHz
Dimensions: 38x36
Weight: 60g
FOV: 150”
Image Rotate: support
Includes
1x Caddx Walnut FPV Action Camera
1x Adjustable Camera Mount
1x Charging Cable
1x Thumb Screw
1x Camera Case
1x Lens Cloth
1x Cable Set
1x ND8 Filter & 1x ND16 Filter (if not CAM ONLY version)
FPV flying has evolved, and the gear that we use needs to evolve with us. Our needs are different: We are carrying larger cameras, we demand smoother flight characteristics so we can capture creamy smooth video, and we need motors that can execute maneuvers in a controlled, super silky way. Camera Butter Halo motors are purpose-designed to have a torque curve, resolution, and feel for butter-smooth FPV flying on a 5 or 6 -inch FPV drone. These motors are fantastic for both freestyle and cinematic flying.
Check out all of our other motors, and all our Camera Butter selection!
Specifications
Kv: 1800Kv
Input Voltage: 5-6S LiPo
Stator Dimensions: 24mm Φ x 06mm
Shaft Diameter: 5mm Φ
Mounting Pattern: 16mm Φ
Wire Dimensions: 20AWG x 150mm
Weight (w/ wires): 29g
Includes
1x Camera Butter Halo Cinematic 2406 1800Kv Motor
Check out this ESC with 32Bit for processing and 45Amps to work with, making this 30x30 4in1 board a great choice for your builds. Also this is the replacement ESC for the CLRACING F7/4in1 stack combo. If used with other flight controllers please make sure you have the correct harness pinout to avoid damaging your flight controller.
Check out all our 30x30 ESCs and our full range of CLRacing products!
Specifications
Input Voltage: 2-6S
Max. Continuous Current: 45A
Max. Burst Current: 55A
Firmware: BLHeli_32
Support: Dshot300-1200/MultiShot/OneShot/ProShot/PMW
Current Sensor: Yes
Current Sensor Scale: 250
Dimensions 43.5mm x 46.5mm
Mounting Dimensions: 30.5x30.5mm Φ4mm
Size : 43.5mm x 46.5mm
Weight: 13.5g
Includes
1x CLRacing 32Bit 45A V2 2-6S 30x30 4in1 ESC
10x M3x5mm nylon thread through spacers
5x M3x25mm nylon screws
5x M3 nylon nuts
5x Yellow Grummits
2x 14 AWG 80mm Silicone wires
1x connection cable
1x Amass XT60
1x Rubycon 1000uf 35v ZLH capacitor
CLRacing is well trusted in the industry and the CLRacing F7 V2.2 45A 2-6S 30x30 Stack/Combo will show you exactly why. Durable, feature rich, and easy to solder to. Check out the specs below!
This F7 FC and 45A 4in1 ESC are available separately as well!
Choose either dual or single gyro version.
Check out all our 30x30 Stacks and Combos and our full range of CLRacing products!
Specifications
FC
Input Voltage: 2-8S
MCU: STM32F722RET6216MHz
IMU: Choose Dual ICM20602 or Single MPU6000
OSD: Yes
BlackBox: 32MB
UARTS: 6
ESC Connections: 6
Reverse Polarity Protection: Yes
Camera Control: Yes
BEC: 5V/1.5A, 3.3V/250mA
Buzzer Pads: Yes
LED Pads: Yes
Mounting Dimensions: 30x30
ESC
Input Voltage: 2-6S
Max. Continuous Current: 45A
Max. Burst Current: 55A
Firmware: BLHeli_32
Support: Dshot300-1200/MultiShot/OneShot/ProShot/PMW
Current Sensor: Yes
Current Sensor Scale: 250
Dimensions 43.5mm x 46.5mm
Mounting Dimesions: 30.5x30.5mm Φ4mm
Weight: 13.5g
Includes
1x CLRacing F7 V2.2 30x30 Flight Controller
1x CLRacing 45A V2 32bit 30x30 4in1 ESC
1x Wiring & Accessory Kit
