All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.1V 3S 550 mAh 90C LiPoBattery is the perfect solution for your 3S quads. Boasting a capacity of 550 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB5503S100AHV
Capacity: 550mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 18x18x70mm (HxWxL)
Net Weight: 43g (+/-2g)
Discharge Rate: 100C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.1V 3S 550mAh 90C LiPo Micro Battery (Long Type) - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.1V 3S 850 mAh 80C LiPo Battery is the perfect solution for your 3S quads. Boasting a capacity of 850 mAh and a discharge rate of 80C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB8503S80A
Capacity: 850mAh
Voltage: 11.1V
Cells Configuration: 3S1P
Pack Dimension: 24x30x63mm (HxWxL)
Net Weight: 80g (+/-3g)
Discharge Rate: 80C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.1V 3S 850mAh 80C LiPo Micro Battery (Square Type) - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 300 mAh 80C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 300 mAh and a discharge rate of 80C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB3003S80AHV
Capacity: 300mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 18x17x53mm (HxWxL)
Net Weight: 28g (+/-2g)
Discharge Rate: 80C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.4V 3S 300mAh 80C LiHV Micro Battery - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 380 mAh 90C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 380 mAh and a discharge rate of 90C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB3803S90AHV
Capacity: 380mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 20x17x55mm (HxWxL)
Net Weight: 32g (+/-2g)
Discharge Rate: 90C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.4V 3S 380mAh 90C LiHV Micro Battery - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 550 mAh 100C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 550 mAh and a discharge rate of 100C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB5503S100AHV
Capacity: 550mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 18x18x70mm (HxWxL)
Net Weight: 43g (+/-2g)
Discharge Rate: 100C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.4V 3S 550mAh 100C LiHV Micro Battery (Long Type) - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 650 mAh 120C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 650 mAh and a discharge rate of 120C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out the rest of our 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB6503S120AHV
Capacity: 650mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 16x30x63mm (HxWxL)
Net Weight: 53g (+/-2g)
Discharge Rate: 120C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.4V 3S 650mAh 120C LiHV Micro Battery - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 660mAh 100C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 660mAh and a discharge rate of 100C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Capacity: 660MAH
Continuous Discharge Rate: 90C/180C
Connector: XT30
Weight: 49g (+/-1g)
Dimensions: 23.5x18x65mm Appr.
Includes
1x Gaoneng GNB 11.4V 3S 660mAh 100C LiHV Micro Battery (Long Type) - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 720 mAh 100C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 720 mAh and a discharge rate of 100C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB7203S100AHV
Capacity: 720mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 22x18x71mm (HxWxL)
Net Weight: 54g (+/-2g)
Discharge Rate: 100C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.4V 3S 720mAh 100C LiHV Micro Battery (Long Type) - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 850 mAh 120C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 850 mAh and a discharge rate of 120C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out the rest of our 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB8503S120AHV
Capacity: 850mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 20x30x63mm (HxWxL)
Net Weight: 68g (+/-3g)
Discharge Rate: 120C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.4V 3S 850mAh 120C LiHV Micro Battery - XT30
All batteries must be shipped by a ground shipping method.
The Gaoneng GNB 11.4V 3S 850 mAh 60C LiHV Battery is the perfect solution for your 3S quads. Boasting a capacity of 850 mAh and a discharge rate of 60C, it provides reliable, efficient power with a long flight time. Including an XT30 connector ensures a secure connection, delivering reliable and consistent power.
Check out our other 3S batteries and our selection of Gaoneng Products!
Specifications
Model No.: GNB8503S60AHV
Capacity: 850mAh
Voltage: 11.4V (LiHV)
Cells Configuration: 3S1P
Pack Dimension: 24x18x71mm (HxWxL)
Net Weight: 52g (+/-2g)
Discharge Rate: 60C
Charge Rate: 1C to 5C
Discharge Connector: XT30
Includes
1x Gaoneng GNB 11.4V 3S 850mAh 60C LiHV Micro Battery (Long Type) - XT30
GEA65003S10E5, Gens Ace 3S LiHV Advanced Series LiPo Battery 100C (11.4V/6500mAh) w/EC5 Connector
Features:
4.35V HV lithium technology
LED power status indicator informs you of battery health
Voltage status indicator
Self-Storage mode discharges battery to safe levels after 5 days of no use
Overcharge prevention technology
Specifications:
Voltage: 3S (11.4V)
Capacity: 6500mAh
Discharge Rate: 100C
Weight: 17.35oz (493g)
Dimensions: 6.49x1.85x1.33" (165x47x34mm) (LxWxH)
Connector Type: EC5
This product was added to our catalog on June 30, 2022
GEA7K3S60D13, Gens Ace 3s LiPo Battery 60C (11.1V/7000mAh) w/T-Style Connector
GensAce batteries have been proven within the Radio Control community to deliver reliable and consistent performance for all modelers alike. All GensAce batteries offer superior cell matching at the factory, and are extremely consistent in selecting matched cells after each and every batch produced. Additionally, low internal resistance (IR), offers modelers stable voltage output throughout the whole duration of the battery.
Specifications:
Nominal Voltage: 11.1V (3S)
Capacity: 7000mAh
Maximum Charge Rate: 1C (7A)
Discharge Rate:
Continuous: 60C
Peak: 120C
Cell Configuration: 3S1P
Watt Hours: 77.7Wh
ROAR Approved: No
Connector:
Battery: T-Style
Balance: XHR
Dimensions (LxWxH): 5.47x1.85x1.57in (139x47x40mm)
Weight: 16.01oz (454g)
This product was added to our catalog on September 2, 2022
Introducing the Moblite7 Ultralight FPV Brushless Whoop! Made in collaboration with FPV pilot "Mr. Shutterbug," this whoop is one of the lightest 75mm drones on the market! And glows in the dark!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 36g With battery
Propellor Size: 75mm
Antenna: Linear Dipole
HappyModel DiamondF4 FR FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CrazybeeF4F
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (3sec)
ESC Firmware: BLheli_S
Factory firmware: O_H_50_REV16_8.HEX
Stack Size: 25x25mm
Dimensions: 29x29mm
Motors
Stator Size: 0802
Kv: 19000
Weight: 1.7g
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x 75mm Frame (Mobula7 frame)
1x Option1: DiamondF4 FR built-in SPI Frsky receiver
4x EX0802 KV19000 Unibell brushless motor
1x HQPROP 40MMX2 propeller(4cw+4ccw)
1x Runcam Nano3
1x Built-in 5.8G 40ch 25mw-200mw VTX
2x 1s 650mah Lipo battery
1x Propeller disassemble tool
1x Screwdriver
1x Happymodel Carry case
This set of 4 EX 1102 13500 Kv brushless motors with 1.5mm shaft are replacements motor for the Happymodel Mobula7 HD brushless cinewhoop, but can be used on any custom build!
This motor will fit the V3 and V2 Mobula 7 frames as well. Check out the rest of our Mobula 7 parts and accessories, everything we carry from Happymodel, and the entire Micro Motor section!
Specifications
Kv: 13500
Input Voltage 2-3S
Configuration: 9N12P
Motor Dimension: Φ13.5x16mm
Stator Dimensions: Φ11x2mm
Shaft Diameter: Φ1.5mm
Weight: 2.8g
Includes
4x Happymodel EX1102 13500Kv (1.5mm Shaft) Whoop/Micro Motor
This set of 4 EX 1102 9000 Kv brushless motors with 1.5mm shaft are replacements motor for the Happymodel Mobula7 HD brushless cinewhoop, but can be used on any custom build!
This motor will fit the V3 and V2 Mobula 7 frames as well. Check out the rest of our Mobula 7 parts and accessories, everything we carry from Happymodel, and the entire Micro Motor section!
Specifications
Kv: 9000
Input Voltage 2-3S
Configuration: 9N12P
Motor Dimension: Φ13.5x16mm
Stator Dimensions: Φ11x2mm
Shaft Diameter: Φ1.5mm
Weight: 2.8g
Includes
4x Happymodel EX1102 9000Kv (1.5mm Shaft) Whoop/Micro Motor
Can be used for any build and a perfect replacement part for the HappyModel Crux3
Check out the our other motors as well as our HappyModel Crux3 Quad and Accessories Collection.
Specifications
KV: 6400
Configuration: 9N12P
Stator Diamter: 12mm
Stator Length: 2.5mm
Out Shaft Diameter: Φ1.5mm
Inner Shaft Diameter: Φ2mm
Motor Dimension(Dia.*Len): Φ15mm*15mm
Weight(g): 4.4g
No.of Cells(Lipo): 2-3s
Includes
1x HappyModel EX 1202.5 6400Kv Micro Motor for Crux3 - CW
Turn your Mobula7 from amazing to amazingly tough! Happymodel has redesigned the Mobula7 frame, making it more rigid and durable and adding some new features. The frame has slots to hold the Super Tiny LED Strip Board and the battery holder can now hold 2S and 3S packs!
The V3 frame will also fit the new Mobula7 HD.
Here's some other upgrades and spares to go with your new frame.
Specification
Wheelbase: 75mm
Weight: 5.5g
Color: Clear or Black(for Mobula7 HD)
Compatibale with: Happymodel 2S 300mah, RDQ 2S 300mah, and the new RDQ 350 2S
HDZero Whoop Lite 25x25 200mw Digital HD VTX - U.FL is here for your drone needs! Perfect for those feather-lite drones where saving every gram matters, this VTX is a digital HD 720p 60fps video transmitter with up to 200mw on 5.8GHz, perfect for racing.
Check out all our VTXs and our HDZero selection.
Specification
1-3S Input
25mW/200mW RF output
Smart Audio Support
25.5x25.2 M2 soft mounting
Antenna Retention
Removal Shielding Box
32.4x32.5mm (29x29mm inner)
4.5grames/4mm Thickness (w/o shielding)
Includes
1x HDZero Whoop Lite 25x25 200mw Digital HD VTX - U.FL
Until now, 1S tiny whoops were the last type of FPV drone that couldn't be converted to digital video due to voltage and weight limits. HDZero Whoop Lite is here to meet these needs: HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g.
Check out all our Shark Byte gear, and our HDZero selection!
Features
Ultra-high sensitive CMOS sensor
Excellent low light performance
HDZero Nano Lite Camera
HDZero Whoop Lite VTX
Removal Shielding Box
Supports Smart Audio
Under 7g in Weight
Antenna Retention
4mm Thickness
1S-3S Input
Specifications
HDZERO WHOOP LITE VTX
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Resolution: 1280x720@60fps
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Weight: 7g total package
HDZERO NANO LITE CAMERA
Size: 14x16x11mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor
FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65°
Includes
1x HDZero Whoop Lite VTX
1x HDZero Nano Lite Camera
1x Dipole Antenna
1x 40mm Mipi Cable
1x Power/Uart Cable
2x Zip ties
4x Rubber Grommet
The HD Zero Whoop VTX is exactly what it sounds like. A small, lightweight whoop profile VTX for Shark Byte systems! Capable of sending a 720p 60FPS video feed at up to 200mW output power, and weighing under 6 grams! Pairs perfectly with the HDZero Nano Camera!
Check out all our Shark Byte gear, and our HDZero selection!
Features
720p 60FPS
Switchable 25mW & 200mW Output
Compatible with all Shark Byte / Byte Frost Receivers
Lightweight!
Specifications
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Dimensions: 32.5x32.5x6mm
Weight: 5.9g
Includes
1x HDZero Whoop VTX for Shark Byte
Due to this item’s size or weight, it is not available for free shipping and may be shipped via ground.
This is a PNP wing, but assembly is still required.
Designed for FPV flying, the Heewing T1 Ranger PNP Twin Motor Wing is a great wing all around. Lightweight and portable, with a quick disassembly design, this build only takes minutes to put together and take apart. A small wingspan with large space for stress-free placement for your electronic equipment. And many other features to check out!
Check out all our PNP wings, Kit wings, and all out HeeWing products!
Features
Two-section hatch with ample room hatch for electronics
High-Quality EPP / Carbon FIber / Aluminum Materials
Supports External FPV Camera Mounting
730mm Fixed Wing Span
Quick Release Structure
Dual Motors
Specifications
Wingspan: 730mm
Length: 645mm
Hight: 140mm
Dimension: 660x225x135mm
Propeller recommend: 5-6 inch
Battery recommend : 4S 1300-2200mah
Battery: 2S~3S 1300mah~5000mah LiPo
Radio System: 2.4G 6CH
Material: EPP / ABS+PC / Carbon fiber / Aluminum
Includes
1x Heewing T1 Ranger PNP Twin-Motor Wing
Experience the ease and precision of the HGLRC RC1 Smart Soldering Iron. With its high-precision temperature control, you can craft and refine your own delicate projects with confidence. The intuitive design and smart features make crafting a breeze, allowing you to create your own pieces of art with an exceptional degree of accuracy. Perfect for intricate soldering tasks, the RC1 enables you to craft with the finesse of a master artisan.
Be sure to check out our tools & building supplies and all our HGLRC products!
Features
The max temperature is 500°C/932°F.
Working power supply: supports PD3.0, QC2.0, DC12V-25V, 3S-6S battery.
0.91-inch OLED display, the brightness display can be adjusted.
Built-in buzzer reminder, automatically heats up when powered on, and can be
turned on and off as you choice.
An intelligent temperature control algorithm, supports temperature compensation and temperature self-calibration.
The shell is made of translucent high temperature resistant and fireproof PC
environmental protection material
Sensitivity can be set to reject interference from environmental factors.
Support °C/°F switching, left and right hand screen flip.
Low voltage protection, high temperature and high voltage alarm, safe and reliable.
Support Chinese and English display switching, firmware upgrade.
C210 Tip, Suitable for precision maintenance.
Compact and very portable, suitable for use in multiple venues.
Size specification: 118mm x 13.5mm
Weight: 23.6g
Specifications
Name: RC1
Maximum voltage: 25V
Maximum power: 60W
Interface Type: Type-C
Operating temperature: 50-500°C/ 122-932°F
Size: 0.91 inch Display
Power supply: PD2.0/3.0, QC2.0/3.0,DC
Includes
1x HGLRC RC1 Smart Soldering Iron - Black Shell
This HGLRC RC2 Smart Soldering Iron offers an adjustable temperature range of up to 450°C/842°F and is compatible with long and short iron tips. It comes with a 0.91-inch OLED display, brightness control, a buzzer reminder, and built-in protection features such as temperature compensation & self-calibration, low voltage & high temperature/voltage alarms. Made from transparent high temperature resistant PC, it also offers support for PD3.0, QC2.0, DC12V-25V, and 3S-6S battery power, and has Chinese & English display switching. Firmware upgrades are available too.
Be sure to check out our tools & building supplies and all our HGLRC products!
Features
Suitable for long and short soldering iron tips, the max temperature is 450°C/842°F.
Working power supply: support PD3.0, QC2.0, DC12V-25V, 3S-6S battery.
0.91-inch OLED display, the brightness display can be adjusted.
Built-in buzzer reminder, automatically heats up when powered on, and can be turned on and off as you choice.
Intelligent temperature control algorithm, supports temperature compensation and temperature self-calibration.
The shell is made of transparent high temperature resistant and fireproof PC environmental protection material.
Sensitivity can be set to reject interference from environmental factors.
Support °C/°F switching, left and right hand screen flip.
Low voltage protection, high temperature and high voltage alarm, safe and reliable.
Support Chinese and English display switching, firmware upgrade.
Specifications
Name: RC2
Maximum voltage: 25V
Maximum power: 65W
Interface Type: Type-C
Operating temperature: 50-450°C/ 122-842°F
Size: 0.91 inch Display
Power supply: PD2.0/3.0, QC2.0/3.0,DC
Includes
1x HGLRC RC2 Smart Soldering Iron - Transparent Case & Purple PCB
This HobbyWing Skywalker 12A 32Bit 2-3S Individual ESC is a high-performance, reliable speed controller for small airplanes, helicopters, and multi-rotor drones. It has a high-speed processor to ensure smooth, powerful operations, and supports 2-3S LiPo batteries. Enjoy a high response rate and low-voltage protection for excellent control and power.
Make sure to check out the rest of our wing products and our entire line of HobbyWing gear!
Features:
Safety arming feature: Regardless the throttle stick position, the motor will not spin after battery connected.
Throttle calibration function: Throttle range can be calibrated to be compatible with different transmitters.
User programmable.
Multiple program methods supported: transmitter stick, LED Program Card. Very easy to program the ESC at home or at the flying field.
Compatible with LiPO and NiMH battery.
Timing can be changed to be suitable for different brushless motors.
Full protection: Low voltage cutoff protection / Over-heat protection / Throttle signal loss protection.
Power connectors and motor connectors are not included.
Specifications
Model: 12AE
Refresh rate of the throttle signal: 50Hz to 432Hz.
Cont.Current: 12A
Peak.Current: 15A
Input Vol (Lipo): 2-3S
BEC Output: 5V@2A (Linear mode)
Size (mm): 38x18x7mm
Weight(g): 19
Wires input: 20AWG-100mm
Wires output: 20AWG-100mm
Output connectors: N/A
Programming: Stick / LED program box
Firmware update: N/A
Weight: 10g
Includes
HobbyWing Skywalker 12AE 2-3S Individual 12A ESC
If you never want to worry about your your 4-in-1 again, Hobbywing's XRotor 65A raises the bar once again! From Captain Vanover himself, this thing is "bullet proof". No matter what type of flight style you choose, this should be a go-to 4-in-1 for everyone! The soft mounts prevent most of the vibration from being transferred to the FC. From freestyle to racing, even long range will not challenge this ESC. The 65A Micro 4-in-1 ESC comes loaded with the latest 32bit tech (the third generation BLHeli_32 code can support up to 128KHz PWM output frequency), DShot1200, Larger FETs, direct pins for a capacitor, and a choice of either a plug n play ESC connector or solder pads for the flight controller.
Check out all our 4in1 ESCs, all our 30x30 ECSs, and all our Hobbywing products!
Features
High-performance 32-bit microprocessor with a running frequency of up to 120MHz for excellent performance.
The third generation BLHeli_32 code can support up to 128KHz PWM output frequency, which can be compatible with more motors.
All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling.
The code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments.
The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us), and Multishot (5-25us).
Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power-up.
The code also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttles. This can be very useful for finding lost crafts.
Specifications
LiPo Power input: 3S-6S
Cont.Current: 65Ax4
Burst Current: 80Ax4
BEC Output: 5V@ 0.6A
Input wires: 12AWG-130mm (Red/Black)
Output Wire: No wires but solder tabs
Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no
Weight: 15.0g
Size: 52x42x6.6mm
Mounting holes: 30.5x30.5mm
Throttle Calibration: Supported
ESC Programming: BLHeliSuite32
Includes
1x Hobbywing XRotor Micro 32bit 65A 4-6S 30x30 4in1 ESC w/ BEC
Another feature rich offering from Matek in the 30x30 class. Loaded with features for digital and analog builds. Matek leads the pack when it comes to quality and performance.
Check out our 30x30 Flight Controllers as well as the entire Matek selection!
Features
STM32F405 has 1MB flash which can run ArduPilot/INAV/BetaFlight
InvenSense the 3rd generation IMU ICM42688-P
9-60V(3~12S LiPo) wide input voltage and voltage sense. and a 9~16V BEC for DJI OSD or analog VTX
8motors+3servos in INAV/BF multirotor mixer.
SH1.0_8pin connector for PnP with 2x 4in1 ESC
SH1.0_6pin connector for PnP with HD System(Caddx Vista & Air Unit)
USB pin breakout for connecting to external USB adapter
Specifications
Input Voltage: 3-12S
MCU: STM32F405RGT6
IMU: ICM42688-P
OSD: AT7456E, DJI OSD
Barometer: SPL06-001 (I2C)
Blackbox: 16M-byte Flash memory
UARTs: 6 + 1x Softserial_Tx option
PWM outputs: 12 (8x Dshot)
I2C: Yes
BEC: 5V 1.5A, Vx, 9~16V/1~2A (3S IN/9V 2A, 4S IN/12V 2A, 6S IN/16V 2A, 8S IN/16V 1.5A, 12S IN/16V 1A)
ADC: 4 (VBAT, Current, RSSI, Airspeed)
PINIO: Yes
Dual Analog Camera Cignal Switchable: Yes
Mounting Pattern: 30x30mm
Dimensions 36x36x5mm
Weight: 7g
Includes
1x Matek F405-HDTE Flight Controller
6x Silicon grommets M4 to M3
1x SH1.0_8pin cable 5cm, 2x SH1.0_8pin connectors
1x SH1.0_6pin to GH1.25_8pin cable 8cm for HD System(Caddx Vista & Air Unit)
Wiring Diagram
Another solid choice in the Matek F405-miniTE 20x20 Flight Controller by a company that leads the pack when it comes to quality and performance.
Check out all our 20x20 FCs as well as the entire Matek selection!
Features
F405 has 1MB flash which can run with ArduPilot. even with INAV firmware.
Redesigned target MATEKF405TE support 8x bi-directional DSHOT.
Support DJI air unit PnP, and a 10V BEC for DJI OSD or analog VTX
Compared with F722-miniSE 8motors or 6motor+2servos, F405-miniTE supports 8motors+3servos in INAV/BF multirotor mixer
Convertible 20mm to 30.5mm mounting
Specifications
Input: 6~30V (2~6S LiPo)
MCU: STM32F405RGT6
IMU: ICM42688-P
OSD: AT7456E
Baro: Goertek SPL06-001 (I2C)
Blackbox: 16M-byte Flash memory
UARTs: 6
PWM outputs: 12 (8 Dshot)
I2C: 1
ADC: 4 (VBAT, Current, RSSI, Airspeed)
Current Sensor: No
PINIO: 2
BEC: 5V 1.7A & 10V 1.4A
Mounting Pattern: 20x20 M2/M3, 30X30 M3
Weight: 5g
Includes
1x Matek F405-miniTE 20x20 Flight Controller
1x 20mm to 30mm conversion plate(blue PCB)
6x Silicon grommets M4 to M3
6x Brass grommets M3 to M2
1x SH1.0_8pin cable 5cm (including 2x 8pin connectors) for 4in1 ESC
1x SH1.0_6pin to GH1.25_8pin cable 8cm for DJI Air Unit
The NewBeeDrone & Joshua Bardwell Smart Power Goggle Cable is a collaboration product between NewBeeDrone and Joshua Bardwell.
Back in Mid 2021, Joshua Bardwell contacted us and brought up the idea of a smart goggle power cable adaptor. We realized that we could make a device to power a goggle through leftover 4S/6S batteries from quads since even if the battery level is at 30%, it still has enough power to supply the goggle.
At first, we thought of just making a very simple power module board that takes 2S-6S batteries and connect it with a 5.5x2.1 DC male plug and use a heat shrink to cover it. However, that method seems too unreliable so we decided to put a power indicator LED light and a buzzer to indicate the number of battery cells when you plug in a battery. The aluminum case acts like a shield to protect the hardware while providing heat dissipation for the power module.
Why do we call it the Smart Power Module? Because it can automatically detect input voltage to indicate battery cell and will output voltage based on the battery voltage. If the battery voltage is too low, it will give a low voltage to trigger the "goggle low voltage" warning.
-Kelvin
Check out all our NewBeeDrone products!
Specifications
Power input port: XT60
Power input support: 3S/4S/6S battery
Calbe Length: 1.5 meters/4.92ft
LED power indicator light
Buzzer indicator: Beep per cell when the battery plugs in. The module will beep 6 times when a 6S battery is plugged in.
Voltage Output: 6.2V - 8.7V (Based on the battery average cell voltage)
Maximum Current: 2A
Includes
1x NewBeeDrone & Joshua Bardwell Smart Power Goggle Cable
PBTPBB22A50C3S, Pit Bull Tires Pure Gold 3S 50C Softcase LiPo Battery (11.1V/2200mAh) w/Battery Life Indicator & XT60 Connector
The Pit Bull RC Pure Gold 3S 50C Softcase LiPo Battery with Battery Life Indicator has been made for extreme performance in any RC from a scale truck to bashing. Pure Gold batteries are built to take abuse, while a built in LED indicator has been placed on the front of each battery to allow easy power status updates! This battery uses an XT60 connector and includes a T-style adapter to allow compatibility with multiple applications.
Features:
Battery Life Indicator allows fast identification of battery power status
XT60 battery connector
T-style battery adapter included
NOTE:
It is not recommended that the adapter is used for charging purposes. This adapter should be used as an ESC adapter only.
The battery should always be balance charged when preparing for use and storage charged before storing.
Specifications:
Capacity: 2200mAh
Voltage: 11.1V (3S)
This product was added to our catalog on July 26, 2021
PBTPBB43A80C3S, Pit Bull Tires Pure Gold 3S 80C Softcase Shorty LiPo Battery (11.4V/4300mAh) w/Battery Life Indicator & XT60 Connector
The Pit Bull RC Pure Gold 3S 80C Softcase Shorty LiPo Battery with Battery Life Indicator has been made for extreme performance in any RC from a scale truck to bashing. Pure Gold batteries are built to take abuse, while a built in LED indicator has been placed on the front of each battery to allow easy power status updates! This battery uses an XT60 connector and includes a T-style adapter to allow compatibility with multiple applications.
Features:
Battery Life Indicator allows fast identification of battery power status
XT60 battery connector
T-style battery adapter included
NOTE:
It is not recommended that the adapter is used for charging purposes. This adapter should be used as an ESC adapter only.
The battery should always be balance charged when preparing for use and storage charged before storing.
Specifications:
Capacity: 4300mAhVoltage: 11.4V (3S)
Voltage: 11.4V (3S)
This product was added to our catalog on July 26, 2021
PBTPBB6A100C3S, Pit Bull Tires Pure Gold 3S 100C Softcase LiPo Battery (11.1V/6000mAh) w/Battery Life Indicator & EC5 Connector
The Pit Bull RC Pure Gold 3S 100C Softcase LiPo Battery with Battery Life Indicator has been made for extreme performance in any RC from a scale truck to bashing. Pure Gold batteries are built to take abuse, while a built in LED indicator has been placed on the front of each battery to allow easy power status updates! This battery uses an EC5 connector and includes a T-style connector to allow compatibility with multiple applications.
Features:
Battery Life Indicator allows fast identification of battery power status
EC5 battery connector
T-style battery plug included
NOTE: This battery should always be balance charged when preparing for use and storage charged before storing.
Specifications:
Capacity: 6000mAh
Voltage: 11.1V (3)
This product was added to our catalog on July 26, 2021
PHB3S5400100EC5, Powerhobby 3s 11.1v 5400mah 100c Lipo Battery w EC5 Plug Hardcase
Powerhobby 3s 11.1v 5200mah 100c Lipo Battery w EC5 Plug Hardcase
100C Continuous / 200C Brust
Perfect for 1/10 & 1/8 scale vehicles, Boats, Planes, Drones. When you want a powerful battery pack that you can depend on even when you push it to its limits, this 3S 5400mah 100C LiPo Battery is for you. Powerhobby Power Pro Series lipo batteries offers very high power and very long run time for your RC models. The 100C burst rate enhances your driving experience no matter what type of driving you are into.These batteries packs are made with superior Lithium Polymer raw materials. The advanced stacking technology enables a single cell of capacity to reach 5400mah. Powerhobby Power Pro Batteries are your ideal choice for your RC Applications.
Specs:
Application(s): 1/10 / 1/8 scale cars, trucks, and buggies, DronesDischarge Connector: EC5Balance Connector: JST-XHLength : 136mmWidth : 44mmHeight: 34mmWeight: 14.3 Ounces
Includes : 1 Battery
Warranty:
This LiPo Battery Pack is guaranteed, under warranty, against defects in materials and workmanship upto 6 Months from the day of purchaseThis warranty does not cover physical damage to the battery pack as the result of a crash, hard landing, improper mounting or any deformity caused by the user.This warranty does not cover internal damage to the battery pack due to overcharging, deep discharging, or excessivedischarge current.
This product was added to our catalog on July 25, 2024
PHB3S6500100CXT60APT, 6500mAh 11.1V 3S 100C LiPO Battery Pack w/ XT60 + Traxxas ADAPTER
Perfect for 1/10 & 1/8 scale vehicles, Boats, Planes, Drones. When you want a powerful battery pack that you can depend on even when you push it to its limits, this 3S 6500mah 100C LiPo Battery is for you. Powerhobby Power Pro Series lipo batteries offers very high power and very long run time for your RC models. The 100C burst rate enhances your driving experience no matter what type of driving you are into.These batteries packs are made with superior Lithium Polymer raw materials. The advanced stacking technology enables a single cell of capacity to reach 6500mah. Powerhobby Power Pro Batteries are your ideal choice for your RC Applications.Specs:
Application(s): 1/10 / 1/8 scale cars, trucks, buggies, Truggies
Discharge Connector: xt60
Balance Connector: JST-XH
Size : 136 x 44 x 34mm (L X W X H)
Weight : 15.6 Ounces
Suggested Charge Rate : 2C
This product was added to our catalog on October 14, 2021
3S 11.1V 7200mAh 100C-200C LiPo Battery w/ Genuine Traxxas Plug
100C Continuous / 200C Brust
Perfect for 1/10 & 1/8 scale vehicles, Boats, Planes, Drones. When you want a powerful battery pack that you can depend on even when you push it to its limits, this 3S 7200mah 100C LiPo Battery is for you. Powerhobby Power Pro Series lipo batteries offers very high power and very long run time for your RC models. The 200C burst rate enhances your driving experience no matter what type of driving you are into.These batteries packs are made with superior Lithium Polymer raw materials. The advanced stacking technology enables a single cell of capacity to reach 7200mah. Powerhobby Power Pro Batteries are your ideal choice for your RC Applications.
Includes:
1 Battery
Features:
Length : 155mm
Width : 45mm
Height : 28.4mm
Specifications:
Suggested Charge Rate: 2c
Continuous Discharge: 100c
Max Burst Rate: 200c
Voltage Output: 11.1v
Weight : 15.4 Ounces
This product was added to our catalog on October 14, 2021
PHB3S9000100CXT60, Power Hobby 3S 11.1V 9000mAh 100C Graphene Lipo Battery w/ XT60
Perfect for 1/10 & 1/8 scale vehicles, Boats, Planes, Drones. When you want a powerful battery pack that you can depend on even when you push it to its limits, this 3S 9000mah 100C LiPo Battery is for you. Powerhobby Power Pro Series lipo batteries offers very high power and very long run time for your RC models. The 200C burst rate enhances your driving experience no matter what type of driving you are into.These batteries packs are made with superior Lithium Polymer raw materials. The advanced stacking technology enables a single cell of capacity to reach 9000mah. Powerhobby Power Pro Batteries are your ideal choice for your RC Applications.
Specifications:
Length : 168mm
Width : 48mm
Height : 32mm
Charge Rate: 2C
Discharge Rate: 100C Constant / 200C Burst
Application(s): 1/10 / 1/8 scale cars, trucks, and buggies
This product was added to our catalog on October 14, 2021
PTK-5116-20, ProTek RC 3S 120C Low IR Si-Graphene + HV Shorty LiPo Battery (11.4V/4500mAh)
The ProTek R/C 3S 130C Low IR Silicon Graphene + HV Shorty LiPo Battery was developed specifically for 1/10 scale rock crawler and rock racer applications. 3S packs that are commonly used in the crawler world are either small, low capacity packs - or large, heavy 4000-5000mAh packs. This 4800mAh battery fills the void and gives scalers a high capacity option that produces more voltage and longer runtimes than a 2200mAh. Plus, when charged at LiHV specs this battery produces 13.05V, instead of the standard 12.6V of a fully charged standard LiPo, meaning performance oriented enthusiasts can take advantage of the light weight, and higher voltage throughout the discharge curve to give them a more consistent power delivery with less fade on the course!
Want more reasons to run this pack? When compared to standard LiPo and LiHV, Silicon Graphene cells deliver improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage - but Graphene + 130C LiPo batteries take that a step further with lower internal resistance, more power, and 300mAh more capacity when compared to the previous ProTek 3S LiHV!
Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 130C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C 130C Graphene + packs are perfect for enthusiasts that demand the absolute best.
Features:
Comparable weight to a 2200mAh pack, 100g lighter than EcoPower 4100mAh
15 grams heavier than the original LiHV 3600 3S battery, and 900mAh more capacity
Great choice for scalers and U4 racers
Great choice for pro class 3S drag racing, boats and airplanes too
Improved power to weight ratio and a lower overall CG
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Increased run time, increased cycle life and increased voltage!
More capacity gram for gram when compared to standard LiPo cells
10C max charge rates - 1C charge rate recommended for longest life
11.4V nominal voltage
NOTE: While these batteries are technically LiHV cells, they can still be charged with a standard LiPo charger. The overall voltage and capacity will be slightly less than if charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the reduced weight and low internal resistance.
Battery Model
HV Shorty 3S LiPo
Application
Crawlers, Drag, Boats & Aircraft
Type
Silicon Graphene
Voltage
11.4V nominal
Capacity @11.1V
4300mAh
Capacity @11.4V
4800mAh
Weight
245g
Connector Type
T-Style
Balance Connector
4 Pin XH
Number of Cells
3 Cell
Configuration
3S1P
Dimensions (WxLxH)
43x93x25.7mm
Maximum Charge Rate
10C (45A)
Burst Current
130C
Watt Hour @11.4V
54.7Wh
Includes:
(1) ProTek R/C Battery w/T-Style Connector
LITHIUM POLYMER SAFETY INFORMATION
IMPORTANT:
DO NOT leave the battery in your model when charging
DO NOT leave unattended when charging
ALWAYS balance charge the battery
ALWAYS use a LiPo charging bag
YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)
YOU MUST not over discharge the Li-Poly battery pack
READ & UNDERSTAND the instructions carefully before operating this battery
NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.
Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on December 16, 2021
Transform your FPV experience with the RCINPOWER GTS V3 1003 10,000Kv Brushless Motor. This motor boasts impressive power, speed, and torque and will leave you stunned. Dare to go faster, farther, and higher than you ever have! Choose between orange with gold accents or blue with pink accents. This motor comes with a a solderless motor connector.
This motor is also available 18,000Kv and 22,000Kv
Check out our micro motors and all our Rcinpower products!
Features
Enables agile and efficient flight maneuvers
Designed specifically for FPV enthusiasts
Compact and powerful microdesign
Specifications
KV: 10000
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 3mm
Shaft Diameter: 1.5mm
Motor Dimension: 13.5x9.2mm
Weight: 3.45 Grams (5cm Wires)
Idle Current (5 Seconds)@4V: 0.8A
No. Of Cells (Lipo): 1-2S
Max Continuous Power (W) 3S: 85
Internal Resistance: 162mΩ
Max Current (3S): 11.5A
Max. Efficiency Current: (1-3A)>84%
Includes
1x RCinPOWER GTS V3 1003 10,000Kv Micro Motor - Choose Color
1x Screw Kit
Transform your FPV experience with the RCinPOWER GTS V3 1003 18000Kv Brushless Motor. This motor boasts impressive power, speed, and torque and will leave you stunned. Dare to go faster, farther, and higher than you ever have! Choose between orange with gold accents or blue with pink accents. This motor comes with a a solderless motor connector.
This motor is also available 10,000Kv and 22,000Kv
Check out our micro motors and all our RCinPower products!
Features
Enables agile and efficient flight maneuvers
Designed specifically for FPV enthusiasts
Compact and powerful microdesign
Specifications
Max. Efficiency Current: (1-3A)>85%
Weight: 3.45 Grams (5cm Wires)
Motor Dimension: 13.5x9.2mm
Internal Resistance: 162mΩ
Max Continuous Power: 54
Color: Gold and Orange
No. Of Cells (LiPo): 1-S
Max Current (3S): 14.6A
Stator Diameter: 10mm
Shaft Diameter: 1.5mm
Configuration: 9N12P
Stator Length: 3mm
Idle Current: 1.3
Includes
1x RCinPOWER GTS V3 1003 18000Kv Micro Motor - Choose Color
Transform your FPV experience with the RCINPOWER GTS V3 1003 22,000Kv Brushless Motor. This motor boasts impressive power, speed, and torque and will leave you stunned. Dare to go faster, farther, and higher than you ever have! Choose between orange with gold accents or blue with pink accents. This motor comes with a a solderless motor connector.
This motor is also available 10,000Kv and 18,000Kv
Check out our micro motors and all our Rcinpower products!
Features
Enables agile and efficient flight maneuvers
Designed specifically for FPV enthusiasts
Compact and powerful microdesign
Specifications
KV: 22000
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 3mm
Shaft Diameter: 1.5mm
Motor Dimension: 13.5x9.2mm
Weight: 3.45 Grams (5cm Wires)
Idle Current (5 Seconds)@4V: 1.5A
No. Of Cells (Lipo): 1S
Max Continuous Power (W) 3S: 67
Internal Resistance: 46mΩ
Max Current (3S): 18.1A
Max. Efficiency Current: (1-3A)>84%
Includes
1x RCinPOWER GTS V3 1003 22,000Kv Micro Motor - Choose Color
This RCinPOWER MCK GTS V4 2207 2100Kv Motor offers superior performance for professional and enthusiast drone racers. Featuring advanced 2207 stator technology and optimized design, these motors offer a clean, aggressive look with all the power you need for your racing needs. Created in collaboration with top pilot MCK and RCinPOWER, these motors deliver the perfect combination of power and style.
Featuring an EZO 9x4x4mm bearing, one-piece bell machined in one piece and 4mm diameter shaft providing all the necessary features to be resistance to crashes.
This motor is perfect for racing, as well as aggressive freestyle.
Check out our vast brushless motors selection, and all our Rcinpower products!
Specifications
Model: RCinPOWER GTS V4 2207 MCK Edition
Configuration: 12N14P
Stator Diameter: 22mm
Stator Length: 7mm
Shaft Diameter: 4mm (Hollow)
Motor Dimension: 27.3 x 30.3mm
Weight: 30.1 Grams (2cm Wires)
Idle Current (10 Seconds)@10V: 1.2A
No. Of Cells (Lipo): 5~6S
Max Continuous Power (W) 5S: 1350
Internal Resistance: 56mΩ
Max Current (3S): 56A
Max. Efficiency Current: (6-10A)>86%
Includes
1x RCinPOWER MCK GTS V4 2207 2100Kv Motor
1x Hardware Set
Reliable, powerful, and available at an amazing price!
The RDQ ESC took nearly a year to prototype, test, and finally be approved for release. This ESC was made with the everyday and beginner hobbyist in mind. This version utilizes the latest 32Bit technology making it a perfect option for the beginner or budget conscious builders who prefer 32bit ESCs. It offers the same performance and reliability found in ESCs like the Spedix GS30 while having an assignable LED, 3-6S Lipo input and the ability to solder a 330uf Capacitor directly to the ESC (the two holes in the middle and on the sides of the ESC).
Don't mistake the great price for a cheap product. The RDQ 32 Bit 30a ESC is as high of a quality of any ESC on the market today - you're simply getting pricing afforded by large production quantities and RDQ working directly with the factory. The ESC can easily handle the most extreme setups available today - your most demanding 6S setups and motors will fly great on these RDQ ESCs. The individual 32bit 30a ESC can run up to DShot1200 and handle up to 6S.
This ESC is packaged "naked" without any wires and features the ability to solder a 330uf Capacitor directly to the two holes in the middle edges of the ESC. If you mount the cap to the esc via the holes, be sure to mount the esc away from prop strike range (either very close to the motor or the center of the frame) and displace the cap appropriately to avoid prop strikes.
BLHeli_32 Suite passthrough capable on Betaflight 3.2.2 and newer.
For wires, we recommend 18awg wire on the battery leads and 22awg on the signal and ground. RDQ carries both!
Check out our ESC selection!
Specifications
Continuous Current: 30A
Burst Current: 40A
Input Voltage: 3S-6S
Weight: 3.56g
Dimensions: 15mm x 30mm
Includes
1x RDQ 3-6S 32Bit DShot1200 30A ESC
Reliable, powerful, and available at an amazing price!
The RDQ ESC took nearly a year to prototype, test, and finally be approved for release. This ESC was made with the everyday and beginner hobbyist in mind. While this version doesn't utilize the latest 32Bit technology (it can run up to 6S and DShot 600), it comes in at a great price making it a perfect option for the beginner or budget conscious. It offers the same performance and reliability found in ESCs like the Spedix 30a while being a fraction of the price, and the ability to solder a 330uf Capacitor directly to the ESC (the two holes in the middle and on the sides of the ESC).
Don't mistake the great price for a cheap product. The RDQ 30a ESC is as high of a quality of any ESC on the market today - you're simply getting pricing afforded by large production quantities and RDQ working directly with the factory. The ESC can easily handle the most extreme setups available today - your most demanding 6S setups and motors will fly great on these RDQ ESCs. The individual 30a BLHeli_S ESC can run up to DShot600 and handle up to 6S.
This ESC is packaged "naked" without any wires and features the ability to solder a 330uf Capacitor directly to the two holes in the middle edges of the ESC. If you mount the cap to the esc via the holes, be sure to mount the esc away from prop strike range (either very close to the motor or the center of the frame) and displace the cap appropriately to avoid prop strikes.
For wires, we recommend 18awg wire on the battery leads and 22awg on the signal and ground. RDQ carries both
Check out our ESC selection !
Specifications
Continuous Current: 30A
Burst Current: 40A
Input Voltage: 3S-6S
Weight: 3.26g
Size: 28x15mm
Includes
1x RDQ 3-6S BLHeli_S DShot600 30A ESC
A reliable GPS with built in compass, all at a great price!
Check out all our GPS modules!
Features
GPS Module, Dual Module Compass
With electronic compass IC HMC5883L
1.25mm spacing between the 6pins patch seat
Specifications
Power Supply:
DC Voltage 2.8V~6.0V
Typical:3.3V or 5.0V
Consumption: Capture 50mA@5V
Receiving Format: GPS, GLONASS, Galileo, BeiDou, QZSS and SBAS
Receiving Channel: 72 Searching Channel
Receiving Sensitivity:
Trace -167dBm
Capture-148dBm
Positioning Time:
Cold Start: 26s Average
Warm Start: 25s Average
Hot Start: 3s Average
Level Positioning Precision: 2m At Open Wind
Output Frequency: 1Hz-10Hz,Default 1Hz
Speed Precision: 0.1 m/s (Without Aid)
Acceleration Precision: 0.1 m/s (Without Aid)
Dynamic Characteristics:
Max Height: 18000m
Max Speed: 5153m/s
Max Acceleration: 4G
UART Interface:
UART Port: TXDA and RXDA
Support Rate: 4800bps to 115200bps,Default 38400dps
Working Temperature:-40℃-+85℃
Storage Temperature:-40℃-+85℃
The Module’s Pins: SDA,GND,TX,RX,VCC,SCL
Size: 28x28x10mm
Weight: 10g
Includes
1x BN-880 GPS Module
1x 15cm Cable
1x 3M double-sided tape square
Setup
Note: Can not use for flight control with SCM, but it is suitable for Open source flight controller. GPS Program Set up documents and instructions: Please click here BN-880 GPS Configuration files
Check out this great demonstration of the Rescue feature from our customer, Bill Adams:
All batteries must be shipped by a ground shipping method.
The RDQ Series Batteries expand their lineup, now offering 2200mah size packs in both 3S and 5S variants. RDQ Series Lipos are known and loved by the community for their keen ability to push harder than any other pack on the market, flight after flight, all while offering the user an unmatched level of value.
Check out our vast selection of RDQ Series of LiPo and all our 3S Batteries!
Specifications
Capacity: 2200mAh
Size: 26*34.5.*107.5mm
Weight: 195.65g
Balance lead: 40mm
XT60 length: 90mm - 95mm
Includes
1x RDQ Series 11.1V 3S 2200mAh 80C FPV Wing or Drone LiPo Battery - XT60
