Monster Truck Terrain Crusher Belted tire pre-glued on WHD wheel 2pc set
This is a pair of Sweep Terrain Crusher Belted Monster Truck Tires, Pre-Mounted on black WHD wheels. The WHD wheels feature a 12 spoke pattern, 1/2 offset, and a 17mm hex for fitment with most 1/8 trucks and monster trucks.
The Terrain Crusher is an all terrain tire tread pattern meant for high speed and high power applications.
Features:
Pre-glued on WHD 12 Spoke wheels with open cells inserts
Wheels made out of Sweep's top secret ROK Hard strong material
Sweep's own rubber compound mixture perfected over a year of R&D at the US facility
Cast molded tires offer a near perfect balance, for longer lifespan and more traction than injection molded tires
Fully belted
Specifications:
Tire: Proprietary Compound
Wheel: 17mm Heavy Duty Hex, 1/2" Wide offset
Belted: Yes
O/D: 142mm
Width: 80mm
Weight: 331gr/Ea
Fits:
Revo / E-Revo 1/10th series w/ 17mm hex hub
Summit series w/ 17mm hex hub
Arrma R/C cars w/ 17mm hex hub
Traxxas Tmaxx / Emaxx w/ 17mm hex hub
Axial Racing Yeti XL w/ 17mm hex hub
HPI Savage w/ 17mm hex hub
Losi LST XXL w/ 17mm hex hub
DHK Maximus w/ 17mm hex hub
This product was added to our catalog on October 3, 2021
HRAERVT46M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (46T)
Traxxas E-Revo VXL 2.0
Traxxas Maxx
Traxxas X-Maxx
Traxxas XO-1
Traxxas XRT
The Hot Racing hardened steel Mod 1 spur gear is an optional upgrade for the Traxxas E Revo 2.0, X-Maxx 6S and 8S, Maxx 4S and XO-1 models. Choose from 50, 52 and 54 tooth options.
NOTE:
Do NOT use the pin system for setting the X-Maxx gear mesh. Instead, manually set the gear mesh without the pins. Refer to the Traxxas manual for instructions (ref. pg.22 Adjusting Gear Mesh)
With the pins removed, use the four 4x16mm button-head cap screws on the bottom to set gear mesh. Loosen the four 4x16mm button-head cap screws. Cut a narrow strip of notebook paper and run it into the gear mesh. Slide the motor and pinion gear into the spur gear. Tighten the four 4x16mm button-head cap screws, and then remove the strip of paper. You should be able to run a fresh strip of paper through the gears without binding them.
Features:
CNC machined hardened steel construction
Black oxide finished
Laser etched tooth count marking
Upgrade for factory plastic spur gear
Specifications:
Overall diameter: 52.8mm
Gear face width: 8mm
Includes:
One (1) mod 1 steel spur gear
This product was added to our catalog on December 16, 2021
TRA5378X, Traxxas Revo Pivot Ball Caps w/ dust boots, rubber (4)/ dust plugs, rubber (4)/ dust
Replacement part for these models:
Traxxas E-Revo VXL 2.0
Traxxas Revo Nitro
This product was added to our catalog on September 7, 2021
PRO117810, Pro-Line Badlands 3.8" Pre-Mounted Truck Tires (2) (Black) w/Raid Wheels (M2)
The Badlands 3.8" tires now come Pre-Mounted on the next generation 3.8" wheel design from Pro-Line, the Raid 3.8" Removable Hex Wheel! Imagine being able to replace a damaged wheel hex without needing to replace your glued tires. These new Raid 3.8" wheels make this possible by using a unique 8x32 interlocking hex design that is secured to the wheel by 8 M3 screws that are spaced 32mm across. The hexes are included and are also available separately (PRO6345-00). The built-in adjustability and ease of use make this a new must-have wheel for bashers everywhere.
Arrma Kraton 6S BLX
HPI Savage Flux HP
HPI Savage X
HPI Savage XL
Team Associated MGT
Traxxas Revo Nitro
Traxxas Summit 1/10
Traxxas T-Maxx
Features:
Tire:
Readers' Choice Award Winning Tread Design
Aggressive Tire Design
Tire Based on Motocross Tread Technology
Large Tire Lugs for the Ultimate in Tire Durability
Made in the USA, since 1982
Wheel:
Removable Hexes Allow you to Easily Replace Damaged Hexes
17mm Wide Offset 8x32 Hexes are Included
Wheel Made from High-strength, Durable DuPont Nylon Material
Raid 10-spoke Wheel Design Mimics Full-size Racing Wheels
M3 Wheel Hex Hardware Included
Specifications:
Height: 5.85" (149mm)
Width: 2.72" (69mm)
Includes:
(2) Pre-Mounted Badlands 3.8" Tires on Raid Black 8x32 Removable Hex Wheels
(2) 8x32 to 17mm 1/2" Offset Hex Adapters
(16) M3 x 12mm long SHCS hardware
This product was added to our catalog on August 14, 2021
HRAERVT54M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (54T)
Traxxas E-Revo VXL 2.0
Traxxas Maxx
Traxxas X-Maxx
Traxxas XO-1
Traxxas XRT
This product was added to our catalog on December 16, 2021
TRA7758A, Traxxas Sledge/X-Maxx/E-Revo VXL 17mm Splined Wheel Nut (Black) (4)
Set of four 17 mm wheel nuts are serrated for extra bite on the wheel to keep them snug no matter how intense the action gets. The beautiful anodized finish combines eye-catching looks with Traxxas-tough durability.
This product was added to our catalog on September 7, 2021
TRA8672, Traxxas Talon EXT 3.8" Pre-Mounted E-Revo 2.0 Tires w/17mm Hex (2) (Black)
This is a pack of two replacement Traxxas Talon EXT 3.8" Tires, Pre-Mounted to Black wheels with a splined 17mm hex. These tires have been glued to the wheel and include an inner foam insert. Just install and go! TSM Rated.
NOTE: These wheels only fit the Traxxas Splined 17mm Axle Hexes; they will not work with standard 17mm hexes.
This product was added to our catalog on May 7, 2021
TRA5472, Traxxas Wheelie Bar Assembled (fits all 1/10th Scale Revo trucks)
Revo wheelie bar assembly features a unique quick release design that is compatible with Revo trucks, nitro and electric. The wheelie bar assembly is easy to install for controlled wheelies on demand. Four snap-in adjustment positions allow you to choose how extreme you want your wheelie action to be. When it is time to head off-road, a convenient quick release tab makes removal and installation a snap. The wheelie bar mount is compatible with all factory Revo configurations including sway bars and wing mounts.
This product was added to our catalog on July 31, 2021
HRASJT253, Hot Racing Traxxas 32P Steel Spur Gear (Grey) (53T)
This is the Hot Racing Steel 32 Pitch, 53 Tooth Spur Gear with grey hardware for the 1/10 Traxxas E-Revo, Jato 3.3, T-Maxx 3.3, T-Maxx 2.5R, Summit, Rally VXL, Slash 4X4, and Stampede 4X4.
Features:
CNC machined and lightened hardened steel construction
Black oxide coating for durability and corrosion resistance
Grey-colored countersunk washers
Specifications:
Number of Teeth: 53
Gear Pitch: 32 pitch (0.8 module)
Mounting Holes: 3
Tooth Face width: 6mm (0.24 inch)
Internal diameter: ~11mm (~0.43 inch)
Includes:
54 tooth 32 pitch spur gear
(3) mounting screws
(3) grey-colored countersunk washers
(3) washers (use as needed underneath countersunk washers to prevent screw ends from protruding too far through spur mounting plate)
Requires:
Hardened clutch bell or pinon gear
Requires a slipper transmission. Will NOT work with vehicle equipped with a center gear differential. Use Hot Racing SSLF2 series gears for vehicles equipped with a center gear differential.
This product was added to our catalog on December 16, 2021
TRA8655R, Traxxas E-Revo 2.0 Steel Center Driveshafts
Traxxas E-Revo 2.0 Steel Center Driveshafts. Package includes an optional set of center driveshafts intended for the E-Revo 2.0 and hardware.
This product was added to our catalog on September 7, 2021
TRA8655, Traxxas E-Revo VXL 2.0 Center Half Shafts (2)
This is a pack of two replacement Traxxas E-Revo VXL 2.0 Center Half Shafts.
This product was added to our catalog on May 7, 2021
TRA8632, Traxxas E-Revo 2.0 Heavy-Duty Front Left Suspension Arm Set (Black)
The Traxxas E-Revo 2.0 Heavy-Duty Front Left Suspension Arm Set features a design which incorporates latest proprietary composite material. Traxxas designed this composite specifically for high loads and hard landings with just the right amount of flex to resist breaking—even in cold weather. Whether you’re sending it at the skatepark, or preparing for the next speed run, these arms were built for extreme punishment.
Package includes optional front left upper and lower suspension arms.
This product was added to our catalog on May 7, 2021
PRO1016610, Pro-Line Badlands MX38 HP Belted 3.8" Pre-Mounted Truck Tires (2) (Black) (M2) w/Raid Wheels
This is a set of two Pro-Line Black MX38 Badlands HP Belted 3.8" Truck Tires, Pre-Mounted on Raid wheels. Pro-Line Badlands tires are known for having a noticeable Motocross inspired tread and the updated Badlands MX38 HP tires improves on this with and even Bigger and Bolder knobby tread. The Badlands MX38 is a true All-Terrain tire that will find traction on any surface but is best suited for loose and loamy dirt, mud or grass.
Pro-Line has used a refined processes to mold a High-Performance herringbone weave pattern Belt directly inside of the Badlands MX38 HP tires that will prevent the tire from ballooning or expanding during use. This design gives maximum control to put the power down even at high speeds. Quit wasting tires and lay down the power with a clear conscious.
The Badlands MX38 HP 3.8" tires provide the incredible grip that you expect from Pro-Line due to the soft M2 compound and the aggressive Motocross inspired tread. In response to customer demand, Pro-line has designed an updated tire size to fit the current generation of Monster Trucks and the MX38 HP delivers at 3.48" wide and 6.8" tall.
Features:
Tire:
Molded-in High-Performance Herringbone Weave Pattern Belt
Aggressive Motocross Inspired Tread Design
Badlands MX38 HP 3.8" tires Will Not Balloon or Expand During Use
Soft M2 Compound Provides Incredible Grip on a Variety of Surfaces
Belted Tires Give You Control to Put the Power Down
Tire Size comes in at 3.48" wide and 6.8" tall
Soft Foam Inserts Included
Made in the USA, since 1982
Wheel:
Removable Hexes Allow you to Easily Replace Damaged Hexes
17mm Wide Offset 8x32 Hexes are Included
Wheel Made from High-strength, Durable DuPont Nylon Material
Raid 10-spoke Wheel Design Mimics Full-size Racing Wheels
M3 Wheel Hex Hardware Included
Specifications:
Height: 6.80" (173mm)
Width: 3.48" (88mm)
Includes:
(2) Badlands MX38 HP Belted 3.8" Pre-Mounted Truck Tires on Raid wheels
Fits:
Arrma Kraton 6S BLX
HPI Savage Flux HP
HPI Savage X
HPI Savage XL
Tekno RC MT410
Traxxas Revo Nitro
Traxxas Summit 1/10
Traxxas T-Maxx
This product was added to our catalog on March 4, 2021
TRA8635, Traxxas E-Revo Axle Carrier Set
This is a replacement Traxxas Axle Carrier Set. This set includes the left and right side, and is for use with 8x16mm and 17x26mm ball bearings. Package also includes four dust boot retainers.
This product was added to our catalog on September 7, 2021
TRA8652, Drive cup, machined steel (2)/ 4x17mm screw pins (2)
Replacement part for these models:
E-Revo® VXL Brushless
This product was added to our catalog on September 7, 2021
TRA8651, Traxxas E-Revo 2.0 Driveshaft Rebuild Kit
This is a replacement Traxxas E-Revo 2.0 Driveshaft Rebuild Kit. This kit includes two barrels and two pins, enough parts to service two driveshafts.
This product was added to our catalog on May 8, 2021
TRA6487R, Traxxas Machined Mod 1.0 Pinion Gear w/5mm Bore (20T)
Traxxas Machined Mod 1.0 Pinion Gear with 5mm Bore. This is an optional machined pinion gear intended for the Traxxas E-Revo 2.0 and the Traxxas Maxx. The gear is available in a variety of tooth count options, please select the specific gear you want from the list above. Package includes one pinion gear.NOTE: For use with steel spur gears.
Traxxas E-Revo VXL 2.0
Traxxas X-Maxx
Traxxas XO-1
Traxxas XRT
This product was added to our catalog on September 7, 2021
PRO1015510, Pro-Line Trencher HP Belted 3.8" Pre-Mounted Truck Tires (2) (Black) (M2) w/Raid Wheels
Pro-Line Trencher HP Belted 3.8" Pre-Mounted Truck Tires feature a High-Performance herringbone weave pattern belt, molded inside the relentless, tall and grippy tread of the Trencher HP tire. These are not your average belted tires! Made for All Terrain bashing, the Trencher HP 3.8" tires will not balloon or expand during use and will still provide the incredible grip that you expect from Pro-Line tires due to the soft M2 compound. Just like all Pro-Line's tires, they are proudly Made in the USA! Like the original Trencher X 3.8" tire, the next generation Trencher HP 3.8" is destined to become the ultimate, go-to Bash tire for your truck!
Please note that the Trencher HP tires are not meant to be extreme speed run tires and have achieved up to 75 mph or about 3,500 RPM under ideal conditions in testing. Over revving your Trencher HP tires could result in breaking the internal belt, which will NOT be covered under warranty. This can be caused by "diffing out" your tires or holding the throttle open while one, two or three of your tires are stopped, which substantially increases the RPM sent to the free-spinning tire or tires.
The Belted Trencher HP 3.8" tires come Pre-Mounted on the next generation 3.8" wheel design from Pro-Line, the Raid 3.8" Removable Hex Wheel! Imagine being able to replace a damaged wheel hex without needing to replace your glued tires! These Raid 3.8" wheels make this possible by using a unique 8x32 interlocking hex design that is secured to the wheel by 8 M3 screws that are spaced 32mm across. The hexes are included and are also available separately (6345-00). The built-in adjustability and ease of use make this a must-have wheel for bashers everywhere!
Features:
Tires:
Molded-in High-Performance Herringbone Weave Pattern Belt
Trencher HP Tire Will Not Balloon or Expand at High Speed
Horizontal H Shaped Tread for Ridiculous Amounts of Traction and Stability
Over-sized Tall Tread is Second-to-none in Durability and Longevity
Perfect for 3.8" Monster Trucks
Extremely Detailed Sidewall Design for that Tough Off-Road Look
Optimum Handling, Durability and Longevity
Made in the Legendary M2 Compound
Made in the USA, since 1982 - Read about Pro-Line Racing's History
Wheels:
Removable Hexes Allow you to Easily Replace Damaged Hexes
17mm Wide Offset 8x32 Hexes are Included
Wheel Made from High-strength, Durable DuPont Nylon Material
Raid 10-spoke Wheel Design Mimics Full-size Racing Wheels
M3 Wheel Hex Hardware Included
Specifications:
Height: 6.70" (170mm)
Width: 4.15" (105mm)
Includes:
(2) Pre-Mounted Trencher HP 3.8" Belted Tires on Raid Black 8x32 Removable Hex Wheels
(2) 8x32 to 17mm 1/2" Offset Hex Adapters
(16) M3 x 12mm long SHCS hardware
This product was added to our catalog on August 20, 2021
TRA8654R, Traxxas 17mm Splined Wheel Hub Hex (Red) (4)
Traxxas E-Revo VXL 2.0
Traxxas Maxx
Traxxas Sledge
This is a pack of two replacement Traxxas 17mm Splined Wheel Hub Hexes, in Red anodize. Also included are four 4x5mm set screws and four 3x14mm pins.
TECH NOTE: Maxx users, TRA8980X or TRA8996X drive shafts are required for use.
This product was added to our catalog on September 7, 2021
TRA8629, Traxxas E-Revo Bulkhead, rear (upper and lower)/ 4x12mm BCS (6) (requires #8622 chassis)
This product was added to our catalog on September 7, 2021
TRA8686, DIFF F/R COMPLETE E-REVO VXL
Accessory part for these models:
E-Revo® VXL Brushless
This product was added to our catalog on September 7, 2021
TRA8630, Traxxas E-Revo Bulkhead, front (upper and lower)/ 4x12mm BCS (6) (requires #8622 chassis)
This product was added to our catalog on September 7, 2021
TRA5660, Traxxas E-Revo Aluminum Motor Mount
This is a replacement Traxxas Aluminum Motor Mount, and is intended for use with the Traxxas E-Revo.
This product was added to our catalog on September 7, 2021
CNC 3D Aluminum Center Skid Plate, for Traxxas E-Revo 2.0
Hot Racing CNC machined billet aluminum Center Skid Plate for the Traxxas E-Revo 2.0.
Features:
CNC machined billet aluminum Center Skid Plate Anodized Black
Replaces factory plastic skid plate
This product was added to our catalog on December 16, 2021
TRA8622, Traxxas E-Revo VXL 2.0 Chassis
This is a replacement Traxxas E-Revo VXL 2.0 Chassis. This chassis requires the TRA8629 and TRA8630 bulkheads.
This product was added to our catalog on September 7, 2021
TRA3485T, VXL 6S ESC
VXL 6S ESCThis advanced Velineon® VXL-6s™ ESC is custom-tuned for the 2000 kV motor to pour on the power you demand for over-the-top fun. An integrated fan cools the oversized heatsink to keep ESC temperatures down and extend run times. Bright LED status lights keep you informed with temperature and voltage warnings. Internal safety programming constantly monitors ESC performance to protect it from damage. The VXL-6s comes pre-programmed with real-time telemetry capability using the optional 6511 Wireless Module (sold separately) installed in a Traxxas TQi™ transmitter. Use the free Traxxas Link™ App to see speed, RPM, voltage and ESC temperature directly on your mobile device.Replacement part for these models:Maxx® Slash®Sledge®
This product was added to our catalog on March 27, 2024
Hot Racing aluminum rear body mount for the 1/10th scale Traxxas E-Revo, E Revo2 Revo 3.3, Slayer Pro 4X4, and Summit.
Features:
CNC Machined 6061 aluminum construction
Anodized black in color
This item was added to our catalog March 3, 2022
HRAERVT3801Aluminum Transmission Case, for Traxxas E-Revo2
Hot Racing aluminum transmission gearbox case for use in the Traxxas E-Revo2
Features:
CNC machined 6061 billet aluminum transmission case
Black anodized color
Black Aluminum Front Body Mount, for Traxxas E-Revo 2.0
Replace the stock plastic body posts on your Traxxas E-Revo 2.0 with this good looking aluminum front body mount from Hot Racing.
Features:
Aluminum construction, black in color
This product was added to our catalog on December 16, 2021
Suspension Pin Mount, for Traxxas E-Revo/ E-Revo2
This is Hot Racing Suspension Pin Mount Revo E-REVO E-Revo2 Mount for the Traxxas Revo.
Features:
CNC machining of 6061-T6
Black anodized aluminum
This product was added to our catalog on December 16, 2021
This is the Hot Racing 65 Tooth, 32 Pitch / 0.8Mod Hardened Steel Spur Gear in Black anodize.
Features:
CNC machined and lightened hardened steel construction
Upgrades factory plastic gear
Black oxide coating for durability and corrosion resistance
Gunmetal/black anodized countersunk washers
Specifications:Number of Teeth: 65Gear Pitch: 32 pitch (0.8 module)Mounting Holes: 3Tooth Face width: 6mm (0.24 inch)
Includes:
(1) 65 tooth 32 pitch (0.8mod) spur gear
(3) mounting screws
(3) washers
(3) gunmetal/black anodized countersunk washers
This product was added to our catalog on December 16, 2021
HRARVO288V06, Hot Racing Traxxas E-Revo Steel SSD CV Drive Set (2)
The Hot Racing Traxxas Revo Steel SSD CV Drive Set is an optional heavy duty splined star drive CVD axle kit for the front or rear of the Traxxas 1/10th scale E-Revo, E-Maxx, Revo 3.3, T-Maxx 3.3, and Summit. These shafts are compatible with vehicles that use the Traxxas TRA5451X axle shafts.Features:
Heavy duty CNC machined #45 hardened carbon steel construction
Replaces factory plastic Traxxas TRA5451X axle driveshaft assembly
Blue anodized aluminum pin capture rings with rubber o-rings to prevent movement
Design eliminates CV pin setscrew
Steel is black finished
Specifications:
Approximate collapsed length: 151mm (5.9 inch)
Approximate full extension resulting in zero shaft engagement: 199mm (7.8 inch)
This product was added to our catalog on December 16, 2021
