HRAERVT46M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (46T) Traxxas E-Revo VXL 2.0 Traxxas Maxx Traxxas X-Maxx Traxxas XO-1 Traxxas XRT The Hot Racing hardened steel Mod 1 spur gear is an optional upgrade for the Traxxas E Revo 2.0, X-Maxx 6S and 8S, Maxx 4S and XO-1 models. Choose from 50, 52 and 54 tooth options. NOTE: Do NOT use the pin system for setting the X-Maxx gear mesh. Instead, manually set the gear mesh without the pins. Refer to the Traxxas manual for instructions (ref. pg.22 Adjusting Gear Mesh) With the pins removed, use the four 4x16mm button-head cap screws on the bottom to set gear mesh. Loosen the four 4x16mm button-head cap screws. Cut a narrow strip of notebook paper and run it into the gear mesh. Slide the motor and pinion gear into the spur gear. Tighten the four 4x16mm button-head cap screws, and then remove the strip of paper. You should be able to run a fresh strip of paper through the gears without binding them. Features: CNC machined hardened steel construction Black oxide finished Laser etched tooth count marking Upgrade for factory plastic spur gear Specifications: Overall diameter: 52.8mm Gear face width: 8mm  Includes: One (1) mod 1 steel spur gear This product was added to our catalog on December 16, 2021

Read more less

TRA5378X, Traxxas Revo Pivot Ball Caps w/ dust boots, rubber (4)/ dust plugs, rubber (4)/ dust Replacement part for these models: Traxxas E-Revo VXL 2.0 Traxxas Revo Nitro This product was added to our catalog on September 7, 2021

Read more less

TRA5472, Traxxas Wheelie Bar Assembled (fits all 1/10th Scale Revo trucks) Revo wheelie bar assembly features a unique quick release design that is compatible with Revo trucks, nitro and electric. The wheelie bar assembly is easy to install for controlled wheelies on demand. Four snap-in adjustment positions allow you to choose how extreme you want your wheelie action to be. When it is time to head off-road, a convenient quick release tab makes removal and installation a snap. The wheelie bar mount is compatible with all factory Revo configurations including sway bars and wing mounts. This product was added to our catalog on July 31, 2021

Read more less

TRA8672, Traxxas Talon EXT 3.8" Pre-Mounted E-Revo 2.0 Tires w/17mm Hex (2) (Black) This is a pack of two replacement Traxxas Talon EXT 3.8" Tires, Pre-Mounted to Black wheels with a splined 17mm hex. These tires have been glued to the wheel and include an inner foam insert. Just install and go! TSM Rated. NOTE: These wheels only fit the Traxxas Splined 17mm Axle Hexes; they will not work with standard 17mm hexes. This product was added to our catalog on May 7, 2021

Read more less

TRA7758A, Traxxas Sledge/X-Maxx/E-Revo VXL 17mm Splined Wheel Nut (Black) (4) Set of four 17 mm wheel nuts are serrated for extra bite on the wheel to keep them snug no matter how intense the action gets. The beautiful anodized finish combines eye-catching looks with Traxxas-tough durability. This product was added to our catalog on September 7, 2021

Read more less

HRAERVT54M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (54T) Traxxas E-Revo VXL 2.0 Traxxas Maxx Traxxas X-Maxx Traxxas XO-1 Traxxas XRT This product was added to our catalog on December 16, 2021

Read more less

HRASJT253, Hot Racing Traxxas 32P Steel Spur Gear (Grey) (53T) This is the Hot Racing Steel 32 Pitch, 53 Tooth Spur Gear with grey hardware for the 1/10 Traxxas E-Revo, Jato 3.3, T-Maxx 3.3, T-Maxx 2.5R, Summit, Rally VXL, Slash 4X4, and Stampede 4X4. Features: CNC machined and lightened hardened steel construction Black oxide coating for durability and corrosion resistance Grey-colored countersunk washers Specifications: Number of Teeth: 53 Gear Pitch: 32 pitch (0.8 module) Mounting Holes: 3 Tooth Face width: 6mm (0.24 inch) Internal diameter: ~11mm (~0.43 inch) Includes: 54 tooth 32 pitch spur gear (3) mounting screws (3) grey-colored countersunk washers (3) washers (use as needed underneath countersunk washers to prevent screw ends from protruding too far through spur mounting plate) Requires: Hardened clutch bell or pinon gear Requires a slipper transmission. Will NOT work with vehicle equipped with a center gear differential. Use Hot Racing SSLF2 series gears for vehicles equipped with a center gear differential. This product was added to our catalog on December 16, 2021

Read more less

HRAERVT52M01, Hot Racing E Revo 2.0/X-Maxx/XO-1 Steel Mod 1 Steel Spur Gear (52T) This product was added to our catalog on December 16, 2021

Read more less

TRA8655, Traxxas E-Revo VXL 2.0 Center Half Shafts (2) This is a pack of two replacement Traxxas E-Revo VXL 2.0 Center Half Shafts. This product was added to our catalog on May 7, 2021

Read more less

TRA8632, Traxxas E-Revo 2.0 Heavy-Duty Front Left Suspension Arm Set (Black) The Traxxas E-Revo 2.0 Heavy-Duty Front Left Suspension Arm Set features a design which incorporates latest proprietary composite material. Traxxas designed this composite specifically for high loads and hard landings with just the right amount of flex to resist breaking—even in cold weather. Whether you’re sending it at the skatepark, or preparing for the next speed run, these arms were built for extreme punishment. Package includes optional front left upper and lower suspension arms. This product was added to our catalog on May 7, 2021

Read more less

TRA8635, Traxxas E-Revo Axle Carrier Set This is a replacement Traxxas Axle Carrier Set. This set includes the left and right side, and is for use with 8x16mm and 17x26mm ball bearings. Package also includes four dust boot retainers. This product was added to our catalog on September 7, 2021

Read more less

TRA6487R, Traxxas Machined Mod 1.0 Pinion Gear w/5mm Bore (20T) Traxxas Machined Mod 1.0 Pinion Gear with 5mm Bore. This is an optional machined pinion gear intended for the Traxxas E-Revo 2.0 and the Traxxas Maxx. The gear is available in a variety of tooth count options, please select the specific gear you want from the list above. Package includes one pinion gear.NOTE: For use with steel spur gears. Traxxas E-Revo VXL 2.0 Traxxas X-Maxx Traxxas XO-1 Traxxas XRT This product was added to our catalog on September 7, 2021

Read more less

TRA8654R, Traxxas 17mm Splined Wheel Hub Hex (Red) (4) Traxxas E-Revo VXL 2.0 Traxxas Maxx Traxxas Sledge This is a pack of two replacement Traxxas 17mm Splined Wheel Hub Hexes, in Red anodize. Also included are four 4x5mm set screws and four 3x14mm pins. TECH NOTE: Maxx users, TRA8980X or TRA8996X drive shafts are required for use. This product was added to our catalog on September 7, 2021

Read more less

TRA5446, Traxxas Revo Wing Black This product was added to our catalog on May 7, 2021

Read more less

TRA8629, Traxxas E-Revo Bulkhead, rear (upper and lower)/ 4x12mm BCS (6) (requires #8622 chassis) This product was added to our catalog on September 7, 2021

Read more less

TRA8630, Traxxas E-Revo Bulkhead, front (upper and lower)/ 4x12mm BCS (6) (requires #8622 chassis) This product was added to our catalog on September 7, 2021

Read more less

TRA5660, Traxxas E-Revo Aluminum Motor Mount This is a replacement Traxxas Aluminum Motor Mount, and is intended for use with the Traxxas E-Revo. This product was added to our catalog on September 7, 2021

Read more less

TRA5345R, Traxxas Steering Linkage & Servo Horn Set This product was added to our catalog on September 7, 2021

Read more less

TRA5452X, U-joints, driveshaft (carrier (4)/ 4.5mm cross pin (4)/ 3mm headed pin (4)/ 4x15mm screw pin (2)/ hex pin (2)/ e-clips (6)/ 3x6x0.5 MW (4)) (metal parts for 2 driveshafts) Driveshaft U-joint rebuild kit. Includes carriers (4), cross pins (4), headed pins (4) screw pins (2), hex pins (2), and E-clips (6). Rebuilds 2 driveshafts. This item was added to our catalog March 13, 2024

Read more less