HWA30401139, HobbyWing Xerun D10 Drift Brushless Motor (13.5T) (Purple) Features: Designed for Drift: The Xerun D10 motors provide the ideal colors to perfectly match your drift machines. Available in Black, Red, and Purple. Banana Plug Quick-Swap Design: The motor comes factory soldered with high quality 3.5mm banana plug for easy access swap to different motors. 3.5mm male head is also included in the XD10 ESC. Stator Designed for Drift: The motor stator is optimized for drift and improves motor efficiency in drift applications. Built-in with high-precision sensors board, combined with drift-specific fan rotors, providing excellent motor linearity and drivability while greatly improves motor efficiency. Lightweight: The 10.5T motor weighs approximately 158g while the 13.5T is at 165g (including 3 gold insert weights). The lightweight motor allows user to easily tweak their weight bias on their car. Fan Rotor: Providing great heat dissipation, power the special-shaped gold fan on the rotor heats the motor while making a pleasant sound, especially when Turbo is turned on. Best paired with XD10 PRO ESC  Specifications: Application: 1/10th Drift car Input Voltage: 2S Lipo KV: 2900kv Rotor: 2 POLE ?5-12.1*24.1-BES*-L3 Weight: 157 / 165 Can Size: 35.7xx52.6mm (1.41x2.07") Shaft Diameter: 3.175mm (0.125")  Shaft Length: 15.0mm (0.591") NOTE: To avoid short circuits, ensure that all wires and joints must be well insulated before connecting the motor to related devices. The M3 screws with a length (no longer than 7mm) are needed when mounting the motor onto your vehicle. Please pay attention to the relevant marks (on the ESC) when soldering/connecting those output wires to the motor and make sure that you will strictly follow the wiring order (between the ESC & themotor) of “A-A, B-B, and C-C”. Please ensure the sensor cable is clean and undamaged when you’re using a sensor ESC. You need to pay attention to the two connectors on the cable when connecting the ESC to the motor. Re-check all the connections between the ESC & the motor and ensure that they are all correct before turning on the ESC. Timing Note: The D10 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing. You can adjust the motor timing after unfastening the screw on the rear end-plate. Please adjust the timing as needed according to the mark (white lines) at the rear end of the motor and fasten the screw after the adjustment. For obtaining optimal performance, you can change the output range and characteristics of your power system by adjusting the motor timing. Increasing the timing can increase the motor speed (RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing usually requires a high(er) ratio. Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the user manual of the ESC. After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about the motor temperature via a infra-red temperature gun. If the temperature is too high, please let the motor cool down first and then test again. If the temperature is still too high, then please reduce the timing or increase the FDR (that is to replace the pinion gear with fewer teeth or spur gear with more teeth). This product was added to our catalog on April 21, 2024

Read more less

HWA38020334, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (13.5T) This is the Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo. Using the precise control of the XR10 Pro G2S combined with a powerful V10 G4 motor gives the user a dominant combo! XR10 Pro G2S 160A ESC: The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC offers all the tuning options needed for competitive racing while giving reliable performance on the track. Helping to keep this ESC reliable is the Frameless Fan Design (FFD) fan system. A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. At the racetrack ESC adjustments can be crucial. The XR10 Pro G2S is packed with features such as several PWM adjustments. From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition.V10 G4 Motor: The V10 G4 Competition Stock Brushless Motor has been greatly optimized to provide maximum torque and increased power. With a lower internal resistance, this motor is more efficient and runs cooler when compared to the G3R motors. To further increase performance the motor adopts a fully exposed stator core allowing more airflow over the stator. The motor also features a high-precision endbell plate to improve consistency and structural stability. Dual sensor ports can be found allowing for different wiring setups.NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended. Features: ESC: Upgraded 32-bit M4 microprocessor with more powerful processing capability guarantees stable control and rapid response. (Industry's highest 32-bit microprocessor, increased processing speed by X4) Peak current up to 1200A. (This is not a typo) Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages. Variable frequency regulation of PWM & amp; brake frequencies allows users to precisely regulate the driving; braking forces (of the motors). Expanded range of the max. brake force brings in the active brake ranges from 101% to 150%. Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency. 10 select-to-use profiles applicable to all 1/10th RC car racing. Internal electronic key switch for long service life, high reliability; and the external switch port for connecting an external switch (included in the product box) is applicable to different situations. Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or WiFi module to the ESC. With the Updated WIFI express module (purchase separately), users are able to program parameters, upgrade firmware and check relevant data during the event using either the iPhone or Android devices. Switchable motor direction (CCW/CW) for various chassis. Multiple protections comes in standard Low-voltage cutoff protection ESC and motor thermal protection Fail safe (throttle signal loss protection) Reverse polarity protection Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real time. Firmware upgrade via Hobbywing multi-function LCD program box or WiFi Express (item sold separately). Motor: Specially designed for high-level racing.  Lightweight: The G4 Modified & Stock motors only weigh 161g & 132g respectively. The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor. The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G4 Stock motors (10.5T~25.5T), the timing is adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees. The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts. The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors effectively keep sand or dirt from getting inside and damaging the motor(s). The use of high-performance stator core, heat (200°C) resistant wire, heat (200°C) resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current endurance guarantees outstanding performance and super durability. Specifications: ESC: Cont./Peak Current: 160A / Burst: 1200A  Battery: 5-6 cells NiMH/NiCd / 2S LiPo  BEC Output: 5V-7.4V Motor Supported: Sensored and sensorless brushless motors  Suitable Motor: 3650 Motors 1/10th Touring Car: 4.5T, 1/10th Buggy: 5.5T Application: Brushless motor system for 1/10th, 1/12th Touring Cars & Buggies Racing, Splash proof Wires: Standard 13AWG 200mm Size: 37.5X30.9X32.5mm  Weight: 90g (with wires) Motor:  kV Rating: 3950kV Cell Count: 2-3S No-Load Current: 4.5A Outer Diameter: 35.8mm Length: 51.4mm Shaft Diameter: 3.175 Weight: 149g Front Bearing: 9x4x4mm Rear Bearing: 8x3x4mm Adjustable Timing: 30-60° Applications: 1/10th Stock Class Racing This product was added to our catalog on July 20, 2022

Read more less