This Flywoo BNF Explorer LR 4" HD 4S Quad comes with Walksnail Avatar V2 & Avatar Micro Cam V2, giving you buttery smooth and stabilized video performance. The advanced quadcopter technology lets you take your FPV adventures to new heights! Choose your receiver between ELRS 2.4GHz and TBS CRSF 915 Mhz for a secure flight. Enjoy the unparalleled performance and take your FPV adventures to new heights with this cutting-edge technology! This long range quad is a small efficient cruiser with a deadcat design eliminating props in your view, perfect for the elite capabilities of the Walksnail system. Be sure to check out our Bind-n-Fly collection and our Walksnail Compatible Quads and Electronics as well as other great products from Flywoo!  Features Compact and lightweight design, weighing less than 250g even with the battery Long flight time of up to 30 minutes User-friendly controls for easy operation Support 1080P 120fps Recording Latency Average Delay 22ms Walksnail Avatar V2 Kit 8G ( Camera & VTX) Walksnail WS-M181 GPS: Featuring the u-blox M10 platform UBX-M10050 GNSS chipset and BUILT-IN QMC5883 MAG, the module offers stronger performance and more accurate positioning. Specification Model: Explorer LR 4 HD Walksnail Sub250 Micro Long Range Brand: FLYWOO Frame: Explorer LR 4 HD Walksnail Frame kit FC and ESC: Goku Versatile F405 Pro Mini Stack ( F405 FC+ 40A ESC ) VTX & Cam: Walksnail Avatar HD Kit V2 (8G) Propeller: Gemfan Hurricane 4024 2 Antenna: Flywoo Circular Polarized 5.8GHz UFL Antenna - LHCP Motor: NIN 1404 V2 ULTRALIGHT FPV MOTOR Weight: 168.4g Flight Controller Specifications MCU: STM32F405BGA GYRO: ICM42688P UARTS: 1/2/3/4/5/6 I2C: SCL/SDA Barometer: BMP280 BEC: 5V 2A / 10V 2A Blackbox: 16M Input Voltage: 2-6S Firmware: FLYWOOF405PRO Mounting: 20x20mm M3 / 30x30mm M4 ESC Soft: Dshot300/600 ESC Telemetry: Yes LED Controller: BF LED F.Port: Yes RSSI: Yes Buzz: Yes Input: 2~6S Lipo (8.4~25.2V) TVS Protection: Yes  ESC Specifications  Con. Current: 40A Burst Current: 45A  Input Voltage: 2-6S Support: DShot300/600 Current Sensor: YES BEC Output: NO Size: 42x42x4mm Mounting Hole: 20x20mm ( M3) Motor Specifications Kv: 2750Kv Input Voltage: 4-6S Stator diameter: 14mm Stator height: 4mm Bearings: NSK Wire Length: 24AWG 150mm Shaft size: 1.5mm Mounting Screw Pattern: 12x12 mm Weight: 8.7g VTX Specifications Communication Frequency: 5.725-5.850GHz Transmitter Power(EIRP):  FCC<30dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm 1/O Interface: JST1.0x4(Power in)JST0.8x6(USB) Mounting Holes: 25.5x25.5mm; 20x20mm Dimensions: 33.5x33.5x10.5mm Storage: 8G Recording: 1080p/720p Weight: 17.6g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 6V-25.2V Supported FC System: Betaflight; Inav; Fettec; ArduPilot; Kiss OSD: Canvas mode Latency Average delay: 22ms Antenna Connector: U.FL Camera Specifications Model Avatar: V2 camera Image Sensor: 1/3.2-Inch 4Mp 4:3sensor Resolution: 1080P/60fps; 720P/100fps; 720P/60fps;1080P/120fps compatibility; 1080P/100fps compatibility Ratio: 4:3 native /16:9 Lens: 2.1mm FOV: 160° Aperture: F2.0 Shutter: Rolling shutter Min.Illumination: 0.001Lux Weight: 7.2g Dimensions: 19x19x22mm Coaxial Cable: 140mm Prop Specifications Diameter: 4" Pitch: 2.4" Blades: 2 Material: Polycarbonate Disk Diameter: 102.33mm Max Prop Width: 13.38mm Hub Thickness: 5.5mm Shaft Hole: 1.5mm Weight: 1.61g Antenna Specifications  Gain: 2.2dBi  Axial ratio: 1.0 Around Band Width: 5.6Ghz – 6.2GHz  Axial Ratio: Around 1.0 Polarization: LHCP Connector: UFL Weight: 1.6g  Include 1x Flywoo BNF Explorer LR 4" Deadcat HD 4S Quad w/ Walksnail Avatar V2 & Avatar Micro Cam V2 - Choose Your Receiver 1x Hardware Kit 8x Gemfan 4024-Bi Blade Balck 2x Battery strap 15x180mm 1x Set of screws

Read more less

Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the elite capabilities of HD Walksnail System. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.  A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Dead Cat Style The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers. New Design Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Efficient Power Combo Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light AIO with ELRS 2.4G RX The drone's GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. This allows for the ultimate lightweight design without sacrificing functionality. HD Digital VTX System The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. More Power, More Flight Time The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed.  Specifications Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit Motor: ROBO 1002 19800KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Propeller: 1608-3 Blade 40mm 1.5mm Shaft Camera: Avatar Lite Cam Weight: 33g GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) ROBO 1002 19800KV Configuration: 9N12P Stator Diamter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.3 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 44 Internal Resistance: 89mΩ Max Current(3S): 11.8A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV:170° Aperture:F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm Includes 1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz 4x 1608 -3 40mm 1.5mm shaft 2x TPU battery mount 1x hardware screws set 4x Prop guards

Read more less

The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system.  The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.  A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor:  ROBO 1002 23500KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Props:  1609 - 4 blade 40mm 1.5mm Shaft HD Digital VTX System:  Walksnail Avatar HD Mini 1S Lite Receiver:  ExpressLRS 2.4GHz Weight:  33g Flight Time:  Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate) Speed:  70km/h (approximate) GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A  Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV: 170° Aperture: F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm  Includes 1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards

Read more less

 All products with batteries must be shipped by a ground shipping method. Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right power performance.  BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate  a bigger battery.  Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP.  Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection! Features The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks. It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter. Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better. Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board. The various colors of the spare parts including the Meteor75 Pro frame and Micro Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it. Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals. HD Digital VTX System The Walksnail Avatar HD Mini 1S Lite uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 7.8g lightweight, compatible with 1S whoop drone. Built-in 8 GB storage, this VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode, Betaflight full OSD display is supported and can be adjusted easily by remote control. Note: Please make sure that the battery voltage must be 3.1V at least when flying, otherwise, the HD digital VTX would stop working. Flight Controller The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC. Meteor75 Pro HD (ELRS) Meteor75 Pro HD (Frsky, PNP, TBS) FC Inside F4 1S 5A FC (Serial ELRS 2.4G) V2.0 F4 1S 5A FC (SPI Frsky) V3.0 Gyro BMI270 BMI270 FC Firmware BETAFPVF411 BETAFPVF411RX UART Port One UART Port Two UART Ports External RX Not Supported Supported Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD. Micro Canopy Lite Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone. Endurance Boosting Battery With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots. Meteor HD Series BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images. Meteor75 Pro Frame Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately. Powerful 1S Drone Combo Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots. Specification Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX) Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero) Camera Adjustable Angle: 0-40° Motors: 1102 22000KV Motor Battery: BT2.0 550mAh 1S Battery Frame: Meteor75 Pro Brushless Whoop Frame Propellers: Gemfan 45mm 3-Blade Propellers Canopy: BETAFPV Micro Canopy Lite Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero) Receiver: Serial ELRS 2.4G/SPI Frsky/TBS FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0 VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero) VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera FAQ Download the FC firmware and CLI dump file for Walksnail and HDZero version. Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit. Click to download the manual for HDZero Whoop Lite Bundle. Includes 1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver 2x BT2.0 550mAh 1S Battery 1x Type-C USB Cable 1x BT2.0 Battery Charger and Voltage Tester 4x 45mm 3-Blade Props (1.5mm Shaft) 1x Screwdriver 1x VTX USB Cable (Walksnail or HDZero Version) 1x Pack of Screws

Read more less

For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 AIR Unit shooting, which can achieve an excellent anti-shake effect. The O3 Air Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: Link Camera: RunCam Wasp Antenna: GEPRC Peano 5.8G LHCP U.FL Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: PNP (built-in DJI receiver), ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 HD Wasp 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut

Read more less

For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: GEPRC 5.8GHz@600mW Camera: Caddx Ratel2 Antenna: GEPRC Peano 5.8G RHCP MMCX Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 Analog 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut

Read more less