Products
RaceDayQuads BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver
All products with batteries must be shipped by a ground shipping method. Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right powerful performance. BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate a bigger battery. Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection! Features The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks. It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter. Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better. Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board. The various colors of the spare parts including the Meteor75 Pro frame and Micro Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it. Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals. HD Digital VTX System HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What's more, pilots can activate and configure its OSD function on Betaflight Configurator. Flight Controller The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC. Meteor75 Pro HD (ELRS) Meteor75 Pro HD (Frsky, PNP, TBS) FC Inside F4 1S 5A FC (Serial ELRS 2.4G) V2.0 F4 1S 5A FC (SPI Frsky) V3.0 Gyro BMI270 BMI270 FC Firmware BETAFPVF411 BETAFPVF411RX UART Port One UART Port Two UART Ports External RX Not Supported Supported Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD. Micro Canopy Lite Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone. Endurance Boosting Battery With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots. Meteor HD Series BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images. Meteor75 Pro Frame Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately. Powerful 1S Drone Combo Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots. Specification Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX) Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero) Camera Adjustable Angle: 0-40° Motors: 1102 22000KV Motor Battery: BT2.0 550mAh 1S Battery Frame: Meteor75 Pro Brushless Whoop Frame Propellers: Gemfan 45mm 3-Blade Propellers Canopy: BETAFPV Micro Canopy Lite Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero) Receiver: Serial ELRS 2.4G/SPI Frsky/TBS FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0 VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero) VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera FAQ Download the FC firmware and CLI dump file for Walksnail and HDZero version. Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit. Click to download the manual for HDZero Whoop Lite Bundle. Includes 1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver 2x BT2.0 550mAh 1S Battery 1x Type-C USB Cable 1x BT2.0 Battery Charger and Voltage Tester 4x 45mm 3-Blade Props (1.5mm Shaft) 1x Screwdriver 1x VTX USB Cable (Walksnail or HDZero Version) 1x Pack of Screws
$219.99
RaceDayQuads BetaFPV BNF Meteor75 Pro HD 1S Brushless Whoop w/ Walksnail Avatar & Nano Cam (BT2.0) - Choose Your Receiver
All products with batteries must be shipped by a ground shipping method. Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right power performance. BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate a bigger battery. Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection! Features The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks. It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter. Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better. Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board. The various colors of the spare parts including the Meteor75 Pro frame and Micro Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it. Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals. HD Digital VTX System The Walksnail Avatar HD Mini 1S Lite uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 7.8g lightweight, compatible with 1S whoop drone. Built-in 8 GB storage, this VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode, Betaflight full OSD display is supported and can be adjusted easily by remote control. Note: Please make sure that the battery voltage must be 3.1V at least when flying, otherwise, the HD digital VTX would stop working. Flight Controller The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC. Meteor75 Pro HD (ELRS) Meteor75 Pro HD (Frsky, PNP, TBS) FC Inside F4 1S 5A FC (Serial ELRS 2.4G) V2.0 F4 1S 5A FC (SPI Frsky) V3.0 Gyro BMI270 BMI270 FC Firmware BETAFPVF411 BETAFPVF411RX UART Port One UART Port Two UART Ports External RX Not Supported Supported Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD. Micro Canopy Lite Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone. Endurance Boosting Battery With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots. Meteor HD Series BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images. Meteor75 Pro Frame Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately. Powerful 1S Drone Combo Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots. Specification Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX) Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero) Camera Adjustable Angle: 0-40° Motors: 1102 22000KV Motor Battery: BT2.0 550mAh 1S Battery Frame: Meteor75 Pro Brushless Whoop Frame Propellers: Gemfan 45mm 3-Blade Propellers Canopy: BETAFPV Micro Canopy Lite Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero) Receiver: Serial ELRS 2.4G/SPI Frsky/TBS FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0 VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero) VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera FAQ Download the FC firmware and CLI dump file for Walksnail and HDZero version. Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit. Click to download the manual for HDZero Whoop Lite Bundle. Includes 1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver 2x BT2.0 550mAh 1S Battery 1x Type-C USB Cable 1x BT2.0 Battery Charger and Voltage Tester 4x 45mm 3-Blade Props (1.5mm Shaft) 1x Screwdriver 1x VTX USB Cable (Walksnail or HDZero Version) 1x Pack of Screws
$264.99
RaceDayQuads BetaFPV BNF Meteor85 2S HD Brushless 85mm Whoop w/ Walksnail Avatar & Nano Cam - ELRS
All products with batteries must be shipped by a ground shipping method. Experience super clear and sharper images with the BETAFPV Meteor85 HD. Based on the newest Meteor85 (2022), it comes with Walksnail Avatar Mini HD VTX or HDZero Whoop Lite Bundle, bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight. Together with 1103 11000KV motors and GF2015 2-blade props that feature strong propulsion, it gives pilots powerful and impressive results. Enjoy an immersive flight experience for freestyle tricks outdoors, and get the perfect shots with the new HD VTX system. Features Lightweight for 52.57g (Walksnail) and 48.30g (HDZero) whoop drone, this new 2S whoop drone with Walksnail HD VTX or HDZero VTX gives pilots an immersive flight experience and impactful visuals. New frame with the low profile of the battery slot, the drone's gravity center is reduced and improved the sense of compactness, perfectly enhancing the trust-to-weight ratio. It is durable and light enough, giving pilots a good balance of weight and a nice punch on a 2S battery. Featuring an upgraded propulsion system and a larger capacity battery. Meteor85 uses GF 2015 2-Blade props with 1103 11000KV motors, which gives full play to the efficiency of the power. Combined with a 450mAh 2S battery, Metero85 can fly up to 6 mins (HDZero) and 5 mins (Walksnail). Adopted with injection molding technique, this canopy is 2.50g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone. Reserve solder pads for the external receivers with UART1 and UART2 on F4 1-2S 12A FC board. The SPI ELRS 2.4G and SPI Frsky version can be used as PNP quadcopter. Specifications Frame: Meteor85 Brushless Whoop Frame Motors: 1103 11000KV Motors Props: Gemfan 2015 2-Blade Propellers Receiver: ELRS 2.4G VTX: 1S Walksnail Avatar Mini HD VTX or HDZero Whoop Battery: 450mAh 2S Battery Weight Without Battery: 52.57g (Walksnail)/48.30g (HDZero) Flight Time: 6 mins (HDZero)/5 mins (Walksnail) Camera Adjustable Angle: 0-45° FC&ESC: F4 1-2S 12A FC (2022) VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero) Camera: Walksnail Avatar Nano Camera/HDZero Nano Lite Camera Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM F4 1S 12A AIO FC CPU: STM32F411CEU6 (100MHZ ) Gyro: Six-Axis BMI270 (SPI connection) SPI ELRS 2.4G Receiver Dimensions: 26mm x 26mm (suitable for whoop pattern mounting hole) OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 (ELRS) Motor Pin Connector: 1.25mm Header Pins USB Port: SH1.0 4-Pin Weight: 4.74 g (without power cable and BT2.0 connector) 1S 12A ESC Input voltage: 1S-2S Built-in ESC with 12A continuous and peak 25A current ESC firmware: C_X_30_48_V0.18.1.hex for Bluejay BB51 hardware Includes 1x Meteor85 Brushless Whoop Quadcopter (2S HD Digital VTX) ELRS 2.4G 1x 450mAh 2S 45C Battery 1x Type-C to SH1.0 Adapter 1x SH1.0 Cable 3x Decorative Parts 4x Gemfan 2015 2-Blade Propellers 1x Walksnail VTX USB Cable (For Walksnail Version) 1x HDZero VTX Converter Cable (For HDZero Version) 1x Pack of Screws 1x User Manual
$229.99
RaceDayQuads BetaFPV F4 20A V1 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ELRS 2.4GHz (UART)
The BetaFPV V1 F4 2-3S AIO is the perfect choice for modern Whoop/Toothpick builds. Featuring an F4 AIO Flight Controller and 20A 4-in-1 ESC with ELRS serial, this setup guarantees smooth, consistent performance. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option. Note: If you use the F4 2-3S 20A AIO FC V1, the serial port of the SBUS receiver is UART5Check out all our whoop flight controllers, and all our BetaFPV gear! Features Designed for HD VTX, it features a dual 9V@2A for DJI O3 and 5V@3A for external device BEC solution to prevent screen blackout on the DJI O3 due to low voltage during throttle increase. It includes a new DJI O3 6-pin PMU for easy installation without soldering, reducing assembly complexity. Newbie friendly. The power range of 2-3S provides increased thrust and improved control with a 20A ESC featuring a single NMOS for continuous current capability. The upgraded onboard receiver allows selective power cutoff for saving power and offers additional UART TX3 and RX3 ports for connecting the external device. The redesigned solder pad layout ensures larger, more secure pads for easy and reliable soldering, while the relocated USB port at the rear facilitates computer tuning. It features an STM32F405RGT6 chip, Integrate Serial ELRS 2.4G receiver, 16M black box, barometer, current meter, reserve 3 complete serial ports and a standard SBUS, support GPS, HD VTX, external receiver, and other equipment. F4 2-3S 20A AIO FC V1 also has extended the USB port to the end for easier parameter adjustment and wiring. And a new DJI O3 6-pin PMU has been added for convenient installation and maintenance.FAQPower cutoff: Removing the chip bead disconnects the power supply, and to reuse the onboard ELRS receiver, soldering the solder pads together restores power.UART3 release: Removing two resistors on the solder pads releases UART3. The left side is TX3, and the right side is RX3. To reconnect, solder the solder pads together when reusing the onboard ELRS receiver.Voltage Switch: The HD VTX connector defaults to 9V. The chip bead is soldered between the 9V pad and the middle pad. To use WalkSnail Avatar HD mini 1s and Lite, please ensure the power supply voltage is 5V. Remove the chip bead first from the 9V pad and solder it between the middle pad and the 5V pad. Alternatively, you can use solder instead the chip bead to switch between the 5V and 9V pads.Motor choice: Avoid selecting motors with excessively high KV ratings, as motors above 20,000KV are prone to burn.Betaflight Firmware and CLIFC firmware: Betaflight_4.4.1_BETAFVF405Download the firmware and CLI dump fileReference link:https://github.com/betaflight/betaflight/releases/tag/4.4.1ESC FirmwareWith BB51 ESC solution, F4 2-3S 20A AIO FC V1 is based on BLHeliSuite16714903 with Bluejay ESC firmware, it supports bidirectional D-shot and RPM filtering in Betaflight, offers 24KHz, 48KHz, and 96KHz fixed PWM frequency for options, and custom start-up melodies. F4 2-3S 20A AIO FC V1 default factory setting is 48KHz and it doesn’t recommend upgrading the 96KHz, or it might cause an error in the motor idle setting, not spinning when disarmed.DO NOT flash the firmware with a shorter interval, otherwise, there will be a certain chance of stalling and burning the flight controller.ESC-Configurator: https://preview.esc-configurator.com/Download BLHeliSuite16714903Download the Bluejay ESC firmware. Please choose C_X_70.HEXConnecting External DevicesPlease note that the board reserves two serial ports and a standard SBUS port, which is available for the external CRSF protocol receiver or GPS module, and SBUS protocol receiver. You can refer to the below picture. Specifications Weight: 5.58g (without motor connectors and power cable), 5.92g (with motor connectors) Mounting Hole Size: 26mm x 26mm CPU*: STM32F405RGT6 (168MHz) Six-Axis: ICM42688P (SPI connection) RX: Serial ELRS 2.4G Receiver RX firmware version: BETAFPV AIO 2400 RX ELRS V2.5.2 Antenna: Enameled wire Blackbox Memory: 16MB Sensor: Barometer(BMP280), Voltage&Current 5V BEC*: 5V 3A@8V supply 9V BEC*: 9V 2A@8V supply USB Port: SH1.0 4-Pin Built-in ESC with 20A continuous and peak 25A current ESC input voltage: 2-3S FC firmfware version: Betaflight_4.4.1_BETAFPVF405 ESC firmware: C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware Signal support: D-shot300, D-shot600 Includes 1x BetaFPV V1 F4 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ELRS Serial Wiring Diagram
$54.99
RaceDayQuads BetaFPV Micro Whoop Canopy for HD Camera - Choose Color
This micro canopy is specially designed for Walksnail Avatar Nano camera, Runcam Nano Lite Camera, or most 14mm nano cameras, supporting an adjustable camera lens of 0-45°. It features high compatibility for both HD Digital VTX and Analog VTX like M03 Analog VTX. Features The canopy is designed with camera mounting holes for an adjustable camera lens of 0-45°. It is suitable for Walksnail Avatar Nano camera, Runcam Nano Lite Camera, or most 14mm nano cameras. Lightweight and two colors for options (Black/Blue). Using it with Meteor Series colorful frame will be more attractive. Recommend frames for Meteor65 Pro, Meteor75, and Meteor85 Adopt with injection molding technique, this canopy is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone. Unique design with three decorative parts like a knight, the drone flies in the air like a scientific spaceship cruising, making it very cool and special. Also, the decorative parts are detachable for better heat dissipation. Mounting Diagram The picture below is the diagram for this canopy. This canopy is applied to 1S Walksnail Avatar Mini HD VTX, HDZero Whoop Lite Bundle, M03 Analog VTX, or most 14mm nano cameras. Other brands' VTXs with similar sizes are available to be mounted on this canopy. Specification Item: Micro Canopy for HD Camera Material: PP Tilt: 0-45° Weight: 2.50g (without decorations), 3.28g (with decorations) Color: Black/Blue Adapted VTX: 1S Walksnail Avatar Mini HD VTX, HDZero Whoop Lite Bundle, M03 25-350mW 5.8G VTX Adapted FPV Camera: Walksnail Avatar Nano Camera, Runcam Nano Lite Camera, or most 14mm nano cameras Adapted Frame: Meteor65 Pro/Meteor75/Meteor85 Includes 1x Micro Canopy for HD Camera (Black/Blue) 3x Decorative Parts 3x M1.4x3 Screws 8x M1.4x5 Screws 3x M2x4 Screws Note: The decorative parts for both Micro Canopy for HD Camera and Canopy for Micro Camera 2022 are unavailable in common use even though they have a similar appearance.
$4.99
RaceDayQuads BetaFPV Pavo Pico HD 81mm Cinewhoop Frame (HD Digital Version) - Black
Pavo Pico is the tiniest 2S Sub100g DJI O3 Cinewhoop frame, working with other popular HD digital VTX such as Walksnail Avatar Pro Kit, Vista Kit, etc. After testing with pilots, this frame has been upgraded by lowering the battery slot height and adding filters and camera protection parts. These updates enhance the camera and HD digital VTX, to give pilots an unparalleled flying experience. The Pavo Pico is an all-new HD 81mm cinewhoop with 45mm props that is designed to be the smallest 2S-3S, sub100g build. Check out the rest of our micro frames and the rest of our BetaFPV gear! Features HD digital VTX bracket made of lightweight and tough injection-molded PP material with an adjusted structure to prevent HD VTX displacement or loss after the crash. Incorporating an angle-limited lens protection print and DJI O3 series filters, It is recommended to purchase, which can increase safety and improve visual quality. The Rubber Damper Vibration damping design reduces low-frequency vibrations and is used with GyroFlow stabilization software for a stable and clear camera image during high-speed flight. To accommodate a wider range of battery sizes, the main body of the frame can be trimmed through DIY methods. Additionally, larger batteries can be installed by using battery straps or printed components. The DJI O3 can be directly installed, while Avatar and Vista require a 20x20 mounting plate and screws (included) for fixation. The naked frame is suitable for users who DIY refit and assemble the HD VTX by themselves. We offer a wider range of colors for the Pavo Pico frames, giving you even more options to choose from. Whether you prefer a bold and bright hue or a more subdued shade, we have a color that will suit your style. You can choose your favorite color or collect them all to create your own unique mix-and-match cinewhoop. Pavo Pico Frame Kit We used ultra-light PP material to make the HD VTX mounting bracket, increasing its toughness. The antenna fixing slot and frame have been fused to reduce damage risk, while the camera's installation height has been lowered with a protective printed part to limit its movable angle to within 30°. Additionally, an O3 filter can be used to protect the lens and enhance image quality. We have incorporated a unique rubber damper vibration-damping design, used with GyroFlow stabilization software, which greatly enhances safety and ensures a smooth, HD image output. When you screw the die-cast screws, please DO NOT screw them too tight to leave room for rubber dampers to absorb vibration. It may cause jello in the video footage. Click to watch the installation guide video for DJI O3 Air Unit on Pavo Pico. And The whoop quadcopter package includes the DJI O3 HD Digital VTX Antenna Mount. DJI O3 Vibration Problem To tackle the challenge of vibration on many whoop drones, the DJI O3 unit is mounted on a carbon fiber plate with 4 rubber dampers. This innovative design ensures peak performance and perfect stability. Troubleshooting To improve video quality when recording with DJI O3 HD VTX, turn off its electronic stabilization and use GyroFlow stabilization software. When fixing the HD VTX bracket with M1.4*10 screws, ensure that the nut just touches the shock-absorbing ball. The Jello effect may occur during the above installation due to 2 reasons: The VTX bracket is over-tightened with the screw and the rubber dumper is totally deformed. To solve this, make sure that the screw is tightened just enough to touch the shock-absorbing ball and keep the ball and bracket loose. If It is a large deformation of the frame or quadcopter blades, replace the frame or blades with larger vibrations if necessary. Note: use acetate tape to bind motor wires and prevent them from drooping and interfering with the propeller's rotation. Upgrade Low Profile Design After collecting feedback through the BETA TEST, we lowered the height of the HD VTX mounting bracket and whoop duct from 60.6mm to 51.5mm and the battery compartment results in a more low profile on the cinewhoop. Pilots can further customize their cinewhoop with DIY options such as battery straps or printable components, allowing for compatibility with a variety of battery sizes. This enables pilots to tailor and enhance their cinewhoop to meet their specific requirements and preferences. Steps as follow: Specification Item: Pavo Pico Brushless Whoop Frame Material: PA12 Wheelbase: 80.8mm Battery Slot Size: 16mmx12.7mm Camera Installation Spacing: 19mm/20mm Color: Black Weight: 11.62g Motor Mounting Hole Position: 3-M1.4-φ6.6mm FC Pattern: 26×26mm, suitable for F4 1S 12A AIO Brushless FC V3 Includes 1x BetaFPV Pavo Pico HD 81mm Cinewhoop Frame (HD Digital Version) - Black
$9.99
RaceDayQuads Fat Shark Recon HD FPV Goggles
The Fat Shark Recon HD’s unparalleled image quality is achieved with a 1080p display viewed through Fat Shark’s patented folded optical engine. The 4” panel delivers a crisp 44-degree FOV image at 60 fps with compatibility with WalkSnail transmitters. Recon retains a reputation as a high-performance goggle at an affordable price while maintaining anti-fog fan features, a comfortable form factor, and glasses accommodating faceplate. Features Ergonomically Molded Headset w/ Adjustable Headband 4 Internal Wide Beam Width Directional Antennas Positive Upgradeable via SD Card 5-Way OSD Button Navigation 1920x1080 TFT 4" Display DVR Record Button Black Menu Button 44° Diagonal FOV USB-C Video Out Specifications Power Supply: 5.1mm Barrel Connector, 7-21V (2S-5S) Center Pin RF: 4 Internal Wide Beam Width Directional Antennas Inter-Pupillary Distance (IPD): 55 - 76mm (fixed) Operating Frequencies: 5.725-5.850GHz Package Size: 517g, 180 x 128 x 98mm Positive Upgradeable: via SD Card Field of View (FOV): 44° Diagonal Dimensions: 170 x 120 x 90mm OSD Navigation: 5-Way Button 4 Inch TFT (1920 X 1080) Record Button: DVR Menu Button: Back Memory: MicroSD Video Out: USB-C Weight: 336.5 g Includes 1x Fat Shark Recon HD FPV Goggles 1x Lens Cleaning Cloth 1x Goggle Strap 1x Power Cable
$169.00
RaceDayQuads FatStraps 2" FPV Goggle Strap for Fatshark, Walksnail or DJI - Choose Your Style
The ultimate strap upgrade for your goggles! FatStraps are comfortable, durable, and available in an array of different styles. Be sure to choose the right version for your goggles: Analog (Closed End Loops) for Fatshark Analog HD Thick (Snap End Loops) for DJI FPV, Walksnail Avatar, Fatshark Dominator HD HD Thin (Snap End Loops) for DJI Goggles 2 & HDZero (note that HD Thin straps should fit all the HD Thick strap goggles) All FatStraps are made in the USA from high quality durable components, and the Military Grade straps are especially tough. The FatShark version has a stationary battery pouch sewn into the right side that perfectly holds your goggle battery or 18650 case. The DJI version has a removable sliding elastic section that allows you to mount your battery anywhere along the strap, or in your pocket. The material, fittings, and stitching on these straps are all top notch. More styles on the way!Check out all our FPV goggles & accessories! Includes 1x Fat Straps 2" FPV Goggle Strap for Fatshark, Walksnail or DJI - Choose Your Style
$24.99
RaceDayQuads FlyFishRC Tony 5 5" Freestyle Frame Kit - Sub250
If you are looking for the next quality ultra-light 5" frame, look no further than the Tony 5! Check out what FlyFishRC has to say about their frame! FlyFishRC is excited to introduce a new addition to the relatively fresh sub-250g 5” freestyle drone category - the FlyFishRC Tony!In this modern era, where our hobby meets with aircraft weight restrictions, flying drones larger than 3” has become increasingly challenging. However, we all love a rip on a good old 5” drone, don't we? That's why we believed it was the perfect time to create an exceptionally lightweight 5-inch frame with the potential to craft a sub-250g 5” drone. And that's how Tony came to life.Our objectives were clear: create a lightweight frame with excellent flight characteristics and durability. While these aims are relatively straightforward with a standard 5-inch frame, working with a sub-250g 5” frame is an entirely different animal. We won't pretend that this frame was developed without any compromises, but we've given our all to make it a frame you'll eagerly take out to fly day after day!Tony is a straightforward and easy-to-build platform, fully O3-ready, equipped with our signature CNC aluminum camera plates to ensure your valuable camera remains maximally protected during all types of crashes. It's also compatible with analog cameras, VTX, as well as the HDZERO and Walksnail HD systems (Please verify dimensions for compatibility with all VTXs).We highly recommend using AIO flight controllers to keep the weight as light as possible, although a 20x20 mini stack will also work well.For instance, to achieve a sub-250g configuration in our test builds, we utilized a 40A AIO FC, CADDX Vista Nebula Pro, 2004 FlyFishRC Flash motors, TBS Crossfire Nano, bi-blade HQ props, GNB HV 380mAh 6S battery, and one battery strap, resulting in an all-up weight of 248.7g.However, if your intention is to use this frame with the DJI O3 system, the all-up weight of such a setup will increase to around 260g, as the O3 is notably heavier than the Vista. In this case, if staying under 250g is crucial, you might contemplate using a 4S version of the same battery or stripping down the O3 to shave off some of the excess weight.Overall, Tony is an exciting frame that offers an incredibly enjoyable flying experience. It provides a distinct feeling of being nimble yet not overly floaty due to its lightness. Get your own Tony today and share your feedback online; we'd love to hear about your experience!Anyway...- WHAT’S YOUR NAME?!- TONYYYYY! Check out our other 5" frames as well as the rest of our FlyFishRC products selection! Features Only 57g (w/TPU) Sub250g capable High structural strength High-end T700 carbon fiber CNC aluminum camera plates Silicone shock-absorbers for O3 AU Compatible with both 19/20mm cameras Compatible with most VTX Compact body, well suited for freestyle Equipped with all accessories needed for analog and HD builds 12.9-grade strength hardware with Loctite threadlocker pre-applied Specifications Model: Tony 5 Geometry: True-X Wheelbase:215mm Arm thickness: 4mm Top plate thickness: 2mm Middle plate thickness: 2mm Bottom plate thickness: 2mm Propeller size: 5inch CNC plate thickness: 4mm FPV cam spacing: 19mm/20mm Weight: 57g(with TPU parts) Total Dimensions:133.7mmx168x29mm Stack mounting holes: 20mmx20mm/25.5mmx25.5.5mm(M3) VTX mounting holes: 20mmx20mm/25.5mmx25.5mm(M2) Includes 1x FlyFishRC Tony 5 5" Freestyle Frame Kit - Sub250
$39.99
RaceDayQuads Flywoo BNF Explorer LR 4" Deadcat HD 4S Quad w/ Walksnail Avatar V2 & Avatar Micro Cam V2 - Choose Your Receiver
This Flywoo BNF Explorer LR 4" HD 4S Quad comes with Walksnail Avatar V2 & Avatar Micro Cam V2, giving you buttery smooth and stabilized video performance. The advanced quadcopter technology lets you take your FPV adventures to new heights! Choose your receiver between ELRS 2.4GHz and TBS CRSF 915 Mhz for a secure flight. Enjoy the unparalleled performance and take your FPV adventures to new heights with this cutting-edge technology! This long range quad is a small efficient cruiser with a deadcat design eliminating props in your view, perfect for the elite capabilities of the Walksnail system. Be sure to check out our Bind-n-Fly collection and our Walksnail Compatible Quads and Electronics as well as other great products from Flywoo! Features Compact and lightweight design, weighing less than 250g even with the battery Long flight time of up to 30 minutes User-friendly controls for easy operation Support 1080P 120fps Recording Latency Average Delay 22ms Walksnail Avatar V2 Kit 8G ( Camera & VTX) Walksnail WS-M181 GPS: Featuring the u-blox M10 platform UBX-M10050 GNSS chipset and BUILT-IN QMC5883 MAG, the module offers stronger performance and more accurate positioning. Specification Model: Explorer LR 4 HD Walksnail Sub250 Micro Long Range Brand: FLYWOO Frame: Explorer LR 4 HD Walksnail Frame kit FC and ESC: Goku Versatile F405 Pro Mini Stack ( F405 FC+ 40A ESC ) VTX & Cam: Walksnail Avatar HD Kit V2 (8G) Propeller: Gemfan Hurricane 4024 2 Antenna: Flywoo Circular Polarized 5.8GHz UFL Antenna - LHCP Motor: NIN 1404 V2 ULTRALIGHT FPV MOTOR Weight: 168.4g Flight Controller Specifications MCU: STM32F405BGA GYRO: ICM42688P UARTS: 1/2/3/4/5/6 I2C: SCL/SDA Barometer: BMP280 BEC: 5V 2A / 10V 2A Blackbox: 16M Input Voltage: 2-6S Firmware: FLYWOOF405PRO Mounting: 20x20mm M3 / 30x30mm M4 ESC Soft: Dshot300/600 ESC Telemetry: Yes LED Controller: BF LED F.Port: Yes RSSI: Yes Buzz: Yes Input: 2~6S Lipo (8.4~25.2V) TVS Protection: Yes ESC Specifications Con. Current: 40A Burst Current: 45A Input Voltage: 2-6S Support: DShot300/600 Current Sensor: YES BEC Output: NO Size: 42x42x4mm Mounting Hole: 20x20mm ( M3) Motor Specifications Kv: 2750Kv Input Voltage: 4-6S Stator diameter: 14mm Stator height: 4mm Bearings: NSK Wire Length: 24AWG 150mm Shaft size: 1.5mm Mounting Screw Pattern: 12x12 mm Weight: 8.7g VTX Specifications Communication Frequency: 5.725-5.850GHz Transmitter Power(EIRP): FCC<30dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm 1/O Interface: JST1.0x4(Power in)JST0.8x6(USB) Mounting Holes: 25.5x25.5mm; 20x20mm Dimensions: 33.5x33.5x10.5mm Storage: 8G Recording: 1080p/720p Weight: 17.6g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 6V-25.2V Supported FC System: Betaflight; Inav; Fettec; ArduPilot; Kiss OSD: Canvas mode Latency Average delay: 22ms Antenna Connector: U.FL Camera Specifications Model Avatar: V2 camera Image Sensor: 1/3.2-Inch 4Mp 4:3sensor Resolution: 1080P/60fps; 720P/100fps; 720P/60fps;1080P/120fps compatibility; 1080P/100fps compatibility Ratio: 4:3 native /16:9 Lens: 2.1mm FOV: 160° Aperture: F2.0 Shutter: Rolling shutter Min.Illumination: 0.001Lux Weight: 7.2g Dimensions: 19x19x22mm Coaxial Cable: 140mm Prop Specifications Diameter: 4" Pitch: 2.4" Blades: 2 Material: Polycarbonate Disk Diameter: 102.33mm Max Prop Width: 13.38mm Hub Thickness: 5.5mm Shaft Hole: 1.5mm Weight: 1.61g Antenna Specifications Gain: 2.2dBi Axial ratio: 1.0 Around Band Width: 5.6Ghz – 6.2GHz Axial Ratio: Around 1.0 Polarization: LHCP Connector: UFL Weight: 1.6g Include 1x Flywoo BNF Explorer LR 4" Deadcat HD 4S Quad w/ Walksnail Avatar V2 & Avatar Micro Cam V2 - Choose Your Receiver 1x Hardware Kit 8x Gemfan 4024-Bi Blade Balck 2x Battery strap 15x180mm 1x Set of screws
$389.99
RaceDayQuads Flywoo BNF Firefly DC16 Nano Baby HD V2.0 1S 1.6" Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz
Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the elite capabilities of HD Walksnail System. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Dead Cat Style The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers. New Design Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Efficient Power Combo Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light AIO with ELRS 2.4G RX The drone's GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. This allows for the ultimate lightweight design without sacrificing functionality. HD Digital VTX System The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. More Power, More Flight Time The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed. Specifications Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit Motor: ROBO 1002 19800KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Propeller: 1608-3 Blade 40mm 1.5mm Shaft Camera: Avatar Lite Cam Weight: 33g GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) ROBO 1002 19800KV Configuration: 9N12P Stator Diamter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.3 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 44 Internal Resistance: 89mΩ Max Current(3S): 11.8A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV:170° Aperture:F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm Includes 1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz 4x 1608 -3 40mm 1.5mm shaft 2x TPU battery mount 1x hardware screws set 4x Prop guards
$239.99
RaceDayQuads Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz
The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system. The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor: ROBO 1002 23500KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Props: 1609 - 4 blade 40mm 1.5mm Shaft HD Digital VTX System: Walksnail Avatar HD Mini 1S Lite Receiver: ExpressLRS 2.4GHz Weight: 33g Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate) Speed: 70km/h (approximate) GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6 GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO Mounting: 25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV: 170° Aperture: F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm Includes 1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards
$239.99
RaceDayQuads Flywoo Explorer LR Analog 4" Frame Kit V2 w/ Atomic RHCP Antenna
Experience long-range cruising with the Flywoo Explorer LR Analog Frame Kit, a collaboration between Flywoo and Dave_C FPV, this ultra-light 4" frame is designed to help you push your FPV skills to the max, without compromising on noise and portability. Made with 100% 3K carbon fiber and 7075 aluminum alloy, the Explorer LR lets you take off and enjoy the thrill of a long-range FPV adventure. Check out the rest of our 4" frames, as well as other great products from Flywoo! Specifications Thickness of arms: 3mm Thickness of top plate: 1.5mm Thickness of bottom plate: 1.5mm Weight: 41g Electronic Mounting: 16x16mm, 20x20mm VTX Mounting: 16x16mm, 20x20, 25.5x25.5mm Motor Bolt Pattern: 9x9mm, 12x12mm Material: 100% 3K carbon fiber, 7075 aluminium alloy Message from Dave_C FPV: "For me personally, Long Range cruising through epic landscapes is the best thing about FPV! But unfortunately, it was always kind of difficult to practice legally and without bothering people with all the noise a massive 6 or 7" long-range quad produces. So the basic idea behind the original Project #MicroLongRange was born: Scale down a 7" long-range quad until it is below 250g take-off weight. With the support of an awesome community on Facebook and Instagram as well as a massive development effort by Flywoo, this concept has seen a lot of improvements that are now all implemented in the Explorer LR! This tiny quad is equipped with GPS, Crossfire, and an independent model finder to give you the necessary confidence to push it to the maximum range of digital and analog video transmission. The powertrain with its GOKU 16x16 stack and the all-new 2700kV 1404 motors spinning 4" props is optimized for maximum efficiency and low weight: Flight times of way over ten minutes on a regular 850mah 4S LiPo battery are easily achievable! Cruising speeds of 40-50 kph (25-30mph) are astonishingly high for such a small quad and have allowed me to do 10km (6 miles) round trips easily. And the best thing about it: It's incredibly quiet! You will barely be able to hear it flying by as soon as you are a few dozen meters away. ” ----- Dave_C FPV Includes 1x Flywoo Explorer LR 4" Walksnail Long Range Frame kit 1x Black TPU 3D Printed Parts 1x M2x5: 8pcs 1x M2x7: 8pcs 1x M2x8: 6pcs 1x M2x12:12pcs 1x Aluminum Standoffs M2*20: 4pcs 1x Aluminum Standoffs M2*25: 2pcs 1x TPU 3D Printed Parts :1 package 1x Flywoo Atomic 5.8G UFL Ant 1 ( RHCP )
$34.99
RaceDayQuads Flywoo Explorer LR HD 4" Frame Kit V2 w/ Atomic LHCP Antenna
Experience long-range cruising with the Flywoo Explorer LR HD Frame Kit, a collaboration between Flywoo and Dave_C FPV, this ultra-light 4" frame is designed to help you push your FPV skills to the max, without compromising on noise and portability. Made with 100% 3K carbon fiber and 7075 aluminum alloy, the Explorer LR lets you take off and enjoy the thrill of a long-range FPV adventure. Check out the rest of our 4" frames, as well as other great products from Flywoo! Specifications Thickness of arms: 3mm Thickness of top plate: 1.5mm Thickness of bottom plate: 1.5mm Weight: 41g Electronic Mounting: 16x16mm, 20x20mm VTX Mounting: 16x16mm, 20x20, 25.5x25.5mm Motor Bolt Pattern: 9x9mm, 12x12mm Material: 100% 3K carbon fiber, 7075 aluminium alloy Message from Dave_C FPV: "For me personally, Long Range cruising through epic landscapes is the best thing about FPV! But unfortunately, it was always kind of difficult to practice legally and without bothering people with all the noise a massive 6 or 7" long-range quad produces. So the basic idea behind the original Project #MicroLongRange was born: Scale down a 7" long-range quad until it is below 250g take-off weight. With the support of an awesome community on Facebook and Instagram as well as a massive development effort by Flywoo, this concept has seen a lot of improvements that are now all implemented in the Explorer LR! This tiny quad is equipped with GPS, Crossfire, and an independent model finder to give you the necessary confidence to push it to the maximum range of digital and analog video transmission. The powertrain with its GOKU 16x16 stack and the all-new 2700kV 1404 motors spinning 4" props is optimized for maximum efficiency and low weight: Flight times of way over ten minutes on a regular 850mah 4S LiPo battery are easily achievable! Cruising speeds of 40-50 kph (25-30mph) are astonishingly high for such a small quad and have allowed me to do 10km (6 miles) round trips easily. And the best thing about it: It's incredibly quiet! You will barely be able to hear it flying by as soon as you are a few dozen meters away. ” ----- Dave_C FPV Includes 1x Flywoo Explorer LR 4" Walksnail Long Range Frame kit 1x Black TPU 3D Printed Parts 1x M2x5: 8pcs 1x M2x7: 8pcs 1x M2x8: 6pcs 1x M2x12:12pcs 1x Aluminum Standoffs M2x20: 4pcs 1x Aluminum Standoffs M2x25: 2pcs 1x TPU 3D Printed Parts :1 package 1x Flywoo Atomic 5.8G UFL Ant 1 ( LHCP)
$34.99
RaceDayQuads Flywoo Explorer LR Walksnail Long Range 4" Frame kit
The Flywoo Explorer LR HD Walksnail Deadcat Long Range 4" Frame kit is designed to fit the Walksnail VTX and accommodate 16x16 and 20x20 flight towers. This compact frame allows you to enjoy the experience of long-range FPV flying without disturbing others or running into legal troubles. Cruise through landscapes with ease and explore with minimal noise. Check out the rest of our 4" frames, as well as other great products from Flywoo! Includes 1x Flywoo Explorer LR 4" Walksnail Long Range Frame kit 1x Black TPU 3D Printed Parts 1x Top plate 1x Bottom plate 1x central plate 2x Front arms 2x Rear arms 2x Side plate 2x Battery straps 1x hardware sets 1x Battery pad 2x insulation sheet
$34.99
RaceDayQuads Flywoo Firefly DC16 Nano Baby V2.0 1.6" Walksnail Micro Frame Kit
Build your own version of the Firefly DC16 micro quad, with this micro frame kit. Check out our other Micro frames, as well as other great products from Flywoo! Feature Compatible with 40mm propellers Specifications Weight: 3.7g Motor Bolt Pattern: 6mm Tri-Mount Stack Size: 25x25mm Includes 1x Flywoo BNF Firefly DC16 Nano Baby V2.0 1.6" Walksnail Micro Frame Kit
$14.99
RaceDayQuads Flywoo Firefly FR16 Nano Baby V2.0 1.6" Walksnail Micro Frame Kit
Build your own version of the Firefly FC16 micro quad, with this micro frame kit. Check out our other Micro frames, as well as other great products from Flywoo! Features Compatible with 40mm propellers Specifications Weight: 3.8g Motor Bolt Pattern: 6mm Tri-Mount Stack Size: 25x25mm Includes 1x Flywoo Firefly FR16 Nano Baby V2.0 1.6" Walksnail Micro Frame Kit
$14.99
RaceDayQuads Flywoo FlyLens 85 2" - 85mm Whoop Frame - Choose Your Version
This does not come with LEDs, those need to be bought separately. The Flywoo FlyLens 85 85mm Whoop Frame provides superior strength and safety with its high-strength PC injection-molded protective ring. The O3\O3Lite Edition has a unique CNC damping platform for recording high-quality video with no jelly effect. It also features a bottom-mounted transmission PC placement compartment, quick-detachable frame for easy separation of parts, and reverse push propeller power for stable flight and longer endurance. You have the option to install your own O3, O3 lite, Walksnail, Vista, or HDZero system. Put some 1003 Motors on FlyLens 85 for a more agile build! Check out the rest of our Whoop Frames & Accessories, and all our Flywoo products! Specifications Brand: FLYWOO Model: Flylens 85 Main Board Thickness: 2mm CNC Gimbal Thickness: 1mm Protective Ring Material: PC+ Flight Control Hole Position: 25.5x25.5mm VTX Mounting: 20/25.5mm Motor Hole Position: 6.6mm/Hole 1.4mm Propeller Size: 2 inch Weight: 27g (Standard) \ 25.5g (Lite) Camera Hole Position (Standard): 20mm Camera Hole Position (Lite): 18mm Includes 1x Flywoo FlyLens 85 85mm Whoop Frame - Choose Your Version
$24.99
RaceDayQuads Flywoo FlyLens 85 Replacement Bottom Plate - Choose your Version
Replacement bottom plate for the FlyLens 85. Check out our Flywoo Frames & Accessories, as well as other great products from Flywoo! Includes 1x Flywoo FlyLens 85 Replacement Bottom Plate - Choose your Version
$6.99
RaceDayQuads Foxeer Mega HD O3 5" Freestyle Frame Kit - Choose Your Color
Experience superior performance and build quality with the Foxeer Mega HD O3 5" Freestyle Frame Kit. Constructed of high-performance T700 carbon fiber for increased stiffness and reduced vibration, this frame is suitable for Analog and HD setups. If you run O3/Analog/Vista/HDzero/Walksnail VTX's then this frame is for you, choose between grey and teal TPU colors. Check out the rest of our 5" frames and our entire Foxeer Collection! Features High quality T700 carbon fiber Aluminum alloy 7075 CNC camera cage O3/Analog/Vista/HDzero/Walksnail Compatible You can download the TPU File Here Specifications Material: Toray T700 carbon with a silky coating Wheelbase: 220mm Middle Mounting Hole: 30.5x30.5mm Rear Mounting Hole: 20x20/25.5x25.5/30.5x30.5mm Camera Size: 19x19/20x20mm Supported System: O3/Analog/Vista/Walksnail/HDZero Weight: 129g (Excluded TPU) Includes 1x Foxeer Mega HD O3 5" Freestyle Frame Kit - Choose Your Color
$75.89
RaceDayQuads Foxeer Mega HD O3 Deadcat 3.5" Micro Frame Kit
The Foxeer Mega HD O3 3.5" Frame Kit provides a strong, light and robust frame for your drone. The kit includes its own high-quality canopy, battery straps, motor mounts and propeller guards, so you can build a powerful and reliable FPV drone quickly and easily. This frame was designed for maximum performance and durability, so you can enjoy a great FPV experience. The deadcat design makes the perfect frame for HD systems like the O3 Air Unit! Check out the rest of our 3.5" frames and our entire Foxeer Collection! Features High quality Japan Toray T700 carbon fiber Aluminum alloy 7075 CNC camera cage O3/Analog/Vista/HDzero/Walksnail Compatible Specifications Material: Toray T700 carbon with a silky coating Wheelbase: 166mm Prop Size: 3.5" Stack Mounting: Middle: 25.5mm M2; Rear:20x20mm/25.5x25.5mm M2 System: Analog, Vista, HDZero, Walksnail, fits O3 with included TPU prints Motor Mounting Pattern: 12x12mm Camera size: 19x19/20x20mm Weight: 85g (Including TPU and screws) Includes 1x Foxeer Mega HD O3 Deadcat 3.5" Frame Kit 1x 2mm Top Plate 1x 2mm Center Plate 1x 2mm Bottom Plate 1x CNC Side Plate 1x M3 x Φ5 x 20 Standoff 1x SMA Antenna Mount 1x Bottom Plate Front Protective Mount 1x M5 Gopro Mount 1x Arm Guard 1x Rx Antenna Mount 1x Isolation Column 1x DJI O3 VTx Mount 1x UFL Antenna Mount 1x Cam Spacer 1x M5 Nut 1x M5x20 Screw 1x Battery Anti-slip 1x 225x15mm Battery Strap
$50.89
RaceDayQuads Foxeer Mega HD O3 Deadcat 4" Frame Kit
The Foxeer Mega HD O3 Deadcat 4" Frame Kit provides a strong, light and robust frame. The kit includes its own high-quality canopy, battery straps, motor mounts and propeller guards, so you can build a powerful and reliable FPV drone quickly and easily. This frame was designed for maximum performance and durability, so you can enjoy a great FPV experience. The Deadcat design makes the perfect frame for HD systems like the O3 Air Unit! Check out the rest of our 4" frames and our entire Foxeer Collection! Features High quality Japan Toray T700 carbon fiber Aluminum alloy 7075 CNC camera cage O3/Analog/Vista/HDzero/Walksnail Compatible Specifications Material: Toray T700 carbon with a silky coating Wheelbase: 192mm Prop Size: 4" Stack Mounting: Middle: 25.5mm M2; Rear:20x20mm/25.5x25.5mm M2 System: Analog, Vista, HDZero, Walksnail, fits O3 with included TPU prints Motor Mounting Pattern: 12x12mm Camera size: 19x19/20x20mm Weight: 89g (Including TPU and screws) Includes 1x Foxeer Mega HD O3 Deadcat 4" Frame Kit 1x 2mm Top Plate 1x 2mm Center Plate 1x 2mm Bottom Plate 1x CNC Side Plate 1x M3 x Φ5 x 20 Standoff 1x SMA Antenna Mount 1x Bottom Plate Front Protective Mount 1x M5 Gopro Mount 1x Arm Guard 1x Rx Antenna Mount 1x Isolation Column 1x DJI O3 VTx Mount 1x UFL Antenna Mount 1x Cam Spacer 1x M5 Nut 1x M5x20 Screw 1x Battery Anti-slip 1x 225x15mm Battery Strap
$50.89
RaceDayQuads Fractal Engineering HD Hardware set for F65/F75 and Wingman - Grommets + Screws
A set of custom-designed and printed, ultra-soft TPE grommets to fit both your whoop AIO and your VTX in a most compact way (8.5mm tall) Fits HDZero, Walksnail, naked Vista, etc… These parts are for the Fractal Engineering Fractal 65 Micro/Whoop Frame Kit and Fractal Engineering Fractal 75 Micro Whoop Frame Kit, and Fractal Engineering Fractal Wingman 1S 18650 Foldable 3" Micro Frame Kit. Check out all our Fractal Engineering Frames & Accessories and our Fractal Engineering Products! Includes 1x Fractal Engineering HD Hardware set for F65/F75 and Wingman - Grommets + Screws
$3.99
RaceDayQuads GEPRC BNF CineLog20 4S 2" Cinewhoop w/ Analog & Micro Cam - ELRS 2.4GHz
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: GEPRC 5.8GHz@600mW Camera: Caddx Ratel2 Antenna: GEPRC Peano 5.8G RHCP MMCX Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 Analog 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut
$216.99
RaceDayQuads GEPRC BNF CineLog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 AIR Unit shooting, which can achieve an excellent anti-shake effect. The O3 Air Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: Link Camera: RunCam Wasp Antenna: GEPRC Peano 5.8G LHCP U.FL Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: PNP (built-in DJI receiver), ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 HD Wasp 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut
$346.99
RaceDayQuads ORT Walksnail/Fatshark 5.8GHz LHCP Upgrade Antenna set
ORT Walksnail/Fatshark antenna set is based on our best-selling Omni and directional antenna, providing wide beamwidth yet strong penetration. With 6.5dBi gain on the compact shield patch and the trusted quality of our pagoda stubby, a great match to upgrade your digital system. Specifications Micro Shield Polarization: LHCP Connector: SMA Gain: 6.5dBi Frequency Range: 5600~6000GHz Gain Pattern: Directional – Need to be pointed on general flying area Beam Width: Vertical and horizontal, 160° at -7db, 130° at -5db, 90° at -3d ORT Pagoda Stubbies Freq Channel: 5550~6050 GHz Gain: 1.2~1.3 dBi Axial Ratio: < 1.3 Matching Swr / S11: S11 < 20dB, VSWR < 1.22 (Center Frequency) Polarization: LHCP Gain Pattern: OmniDirectional (cover signal in all directions) Radiation Efficiency: 95% Includes 2x Micro Shield 5.8GHz 2x Pagoda 2 Stubbies
$55.99
RaceDayQuads Sub250 Nanofly20 2" Micro Frame Kit
The long-awaited second member of the Nanofly family "Nanofly20!" is released! "Change your flying habits in small spaces". The Nanofly20 is equipped with a two-inch propeller, and the motor mounting hole is 3-M1.4-Ø6.6, which can easily install most of the 1002 motors and 1102 motors on the market. Its overall lightweight design achieves a light feel, "as light as a swallow". The 25.5 flight controller holes can be installed with mainstream flight controllers on the market. Install a highly integrated sub 1s 5A flight controller, so that it can take off with only one flight controller board plus a camera and motor. It can also be used with Walksnail Avatar VTX and HDZero VTX. Features "Light as a swallow" lightweight design, with an overall weight of 8.4g, giving more installation space for your electronic equipment. Carbon fiber bottom plate design, body strength pro beyond. 25.5mm flight controller installation holes allow for easy installation of the market's most popular AIO flight controllers. Ø6.6 M1.4-3 motor mounting holes, compatible with most motors such as 0803, 1002, and 1102. Match a variety of VTX solutions to build your own HD FPV mini drone. Specifications Item: Nanofly20 frame Wheelbase: 88mm Arm plate: 1.5mm Motor holes: 3-M1.4-EQS-Ø6.6 FC mounting holes: 25.5x25.5 Camera installation space: 14x14 (mm) Weight: 8.4g Includes 1x Nanofly20 Frame 1x Battery cabin4x M2x18 Round head screw4x M2x12 Round head screw2x M2x3 Round head screw2x M1.4x3 Round head cross screw
$14.99
RaceDayQuads Walksnail Avatar HD Goggle RP-SMA Antenna 2 Pack - LHCP
Replacement antenna 2 pack for the Walksnail Avatar Goggles. Also compatible with Fat Shark Dominator HD. Check out all our RP-SMA antennas and our selection of Walksnail HD products! Specifications Cross-Polarization Rejection: -15 to -30dBi Radiation Efficiency: >97% Dimensions: 24.8x15.3mm Bandwidth: 5.6-6GHz Average Gain: 1.9dBi Connector: RP-SMA Polarization: LHCP Model: Red Bird Weight: 4.2g VSWR: <1.3 Includes 2x Walksnail Avatar HD Goggle RP-SMA Antenna - LHCP
$15.89
RaceDayQuads Walksnail Avatar HD Micro Camera & VTX Kit (Compatible w/ Fat Shark Dominator HD)
The Micro Camera and VTX Combo for Fat Shark Dominator HDO3 are provided by WalkSnail. The video transmitter for the Fat Shark Dominator HD Goggles and Walksnail Goggles has arrived! The first of new generation of HD cameras and video transmitters, they feature lower latency, reduced weight and more convenient form factor while also managing to cram antenna diversity and an 8gb onboard 1080 DVR in there!Also available with Nano camera. Check out all our Walksnail HD products! Features Compatible with FatShark Dominator HD FPV Goggles Canvas mode and distance detection with the dual-antenna system Reliable digital HD video transmission (1080P – H.265 encoding) 8gb onboard DVR Lightest digital VTX (only 16 grams) Ultra low-latency (22ms) Specifications Video Transmitter Video Resolution: 1080p / 720p Antenna Connector: U.fl Channels: 8 Operational Frequency: 5.725-5.850GHz Latency: 22ms Average Input Voltage: 6-25.2V Transition Power: FCC<30dBm / CE <14dBm / SRRC <20dBm / MIC <25dB Internal Storage: 8GB FC Connection Port: JST1.0 x 6 Operating Temperature: -20° to 40° Supported FC Firmware: Betaflight USB Connection: JST x 4 to USB-A Mounting: 25x25mm Dimensions: 33x33x9.5mm Weight: 16g Camera Image Sensor: 1/27" Resolution: 1080p 60FPS / 720P 120FPS / 720P 60FPS Aspect Ration: 16/9 and 4/3 Switchable Lens: 2.1mm Field Of View: 170° Aperture: F 2.0 Shutter Style: Rolling Shutter Minimum Illumination: 0.001Lux Cable Length: 140mm Dimensions: 19x19x22mm Weight: 6g Antennas Polarization: LHCP Bandwidth: 5.6-5.9GHz Gain: 2dBi Average Radiation Efficiency: >= 98% VSWR: <=1.4 Connector: U.fl Length: 90mm Weight: 1.5g Includes 1x Walksnail HD Micro Camera 1x Avatar HD VTX 2x Antennas 1x FC Connection Cable 1x USB Adapter 4x M2 3mm Screws 4x M2 4mm Screws 4x M2 5mm Screws 2x M1.2 1.5mm Screws
$128.99
RaceDayQuads Walksnail Avatar HD Micro Camera & VTX Kit V2 - Choose Version
The Micro Camera and VTX Combo for Fat Shark Dominator HDO3 are provided by WalkSnail. The video transmitter for the Fat Shark Dominator HD Goggles and Walksnail Goggles has arrived! The Walksnail Avatar HD Pro Kit features a VTX with enhanced TVS protection and support for up to 6S. The VTX is resistant to GPS interference with a wide input voltage range of 6V to 25.2V. This kit also features 1080P compatibility, high frame starlight, a 4KM range, and an 8GB and 32GB built-in storage option. The 32GB VTX delivers unmatched stability due to the aid of being equipped with Gyroflow technology. This allows super smooth and stabilized video from your FPV system. Enjoy the unparalleled performance and take your FPV adventures to new heights with this cutting-edge technology! Check out all our Walksnail HD products! Features Compatible with FatShark Dominator HD FPV Goggles Canvas mode and distance detection with the dual-antenna system Reliable digital HD video transmission (1080P – H.265 encoding) Ultra low-latency (22ms) 2K pixel, 120fps, 4:3 native sensor Support Gyroflow 1080P HD FPV F/2.0 Large Aperture 160° wide-angle FOV VTX Specifications Communication Frequency 5.725-5.850GHz Transmitter Power (EIRP) FCC:<30dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm 1/O Interface JST1.0x4(Power in)JST0.8x6(USB) Mounting Holes 25.5x25.5mm; 20x20mm Dimensions 33.5x33.5x10.5mm Storage 8G/32G Recording 1080p/720p Weight 17.6g Operating Temperature -20-40℃ Channels 8 Wide Power Input 6V-25.2V Supported FC System Betaflight; Inav; Fettec; ArduPilot; Kiss OSD Canvas mode Latency Average delay 22ms Antenna 1(IPEX) Camera Specifications Model Avatar V2 camera Image Sensor 1/3.2-Inch 4Mp 4:3sensor Resolution 1080P/60fps; 720P/100fps; 720P/60fps;1080P/120fps compatibility; 1080P/100fps compatibility; Ratio 4:3 native /16:9 Lens 2.1mm FOV 160° Aperture F2.0 Shutter Rolling shutter Min.Illumination 0.001Lux Weight 7.2g Dimensions 19x19x22mm Coaxial Cable 140mm Gyroflow supported/ non-supported, two version Antenna Specifications Polarization LHCP Bandwidth 5600MHz-6000MHz. Gain 1.9dBi VSWR ≤1.5 Input Impedance 50Ω Interface IPEX-1 Size R15x45mm (without cable) Weight 2g Includes USB transfer extension cable X1 4 Pin silicone cable X1 M2x4mm screws X8 M2x5mm screws X4 M2x6mm screws X4 M2x14mm screws X4 M2x5x0.5mm gasket X4
$158.99
RaceDayQuads Walksnail Avatar HD Mini 1S VTX Kit VTX w/ Nano Camera
The Walksnail Avatar HD Nano Camera / Mini 1S VTX Kit features a nano digital camera, antenna, and mini VTX that works with HD Goggles such as the Walksnail Avatar and Fat Shark HD Dominator. This mini HD VTX combo has lower latency than the competitor at an average of 22ms, with an onboard DVR, 5.8GHz frequency, 8Gb internal storage, and a switchable aspect ratio. Check out all our Walksnail HD products! Features Lower latency than the competitor at an average of 22ms 6.8g Lightweight Mini VTX great for the 75x Quad Walksnail Avatar Mini 1S VTX Module Walksnail Avatar Nano Camera Built-in 8Gb Internal Storage 1080p Screen Resolution Switchable Aspect Ratio Walksnail IPEX Antenna 5.8GHz Frequency Onboard DVR Canvas Mode 170° FOV 3.1V-5V Specifications AVATAR HD NANO CAMERA Resolution: 1080p 60FPS / 720P 120FPS / 720P 60FPS Aspect Ration: 16/9 and 4/3 Switchable Minimum Illumination: 0.001Lux Shutter Style: Rolling Shutter Dimensions: 14x14x17mm Cable Length: 90mm Image Sensor: 1/27" Field Of View: 170° Aperture: F 2.0 Lens: 2.1mm Weight: 3.5g AVATAR MINI 1S VTX MODULE Transition Power: FCC<25.5dBm / CE <14dBm / SRRC <20dBm / MIC <25dB I/O Interface: JST1.0 x 6 (Power In) to JST1.0 x 4 (USB) Operational Frequency: 5.725-5.850GHz Operating Temperature: -20° to 40°c Supported FC Firmware: Betaflight Video Resolution: 1080p / 720p Dimensions: 33x33x6.5mm Antenna Connector: IPEX Bitrate: 25mbps/50mbps Mounting: 25.5x25.5mm Latency: 22ms Average Internal Storage: 8GB Input Voltage: 3.1-5V OSD: Canvas Mode Weight: 6.8g Channels: 8 WALKSNAIL AVATAR VTX ANTENNA Radiation Efficiency: >= 98% Bandwidth: 5.6-5.9GHz Gain: 2dBi Average Polarization: LHCP Connector: IPEX Length: 90mm VSWR: <=1.4 Weight: 1.5g Includes 1x Walksnail Avatar HD Nano Camera w/ Avatar Mini 1S VTX 1x 6-Pin Power Cable 2x M2 4mm Screws 1x 4-Pin USB Cable
$109.99
RaceDayQuads Walksnail Avatar HD Nano V3 20x20 VTX Kit w/ Nano Camera (Compatible w/ Fat Shark Dominator HD)
The Walksnail Avatar HD Nano Camera V3 / Avatar HD Mini VTX V3 features a nano digital camera, antenna, and mini VTX that works with HD goggles such as the Walksnail Avatar and Fat Shark HD Dominator. The Avatar V3 is the upgraded version of the Avatar 1S, where the V3 improves with 32G of storage, 500mW of power, a native 4:3 sensor, and a wide voltage range of 3.1-13V. Check out all our Walksnail HD products and check out all our Walksnail compatible products! Features 3.1~13V 500mW FOV160° Metal case 1080P/60fps 4:3 native sensor Built-in 32G storage 18.5g light-weight Nano Camera 14x14mm Walksnail Avatar HD Nano Kit V3 The Walksnail Avatar HD Nano Kit V3 supports 1080P/60fps, with a 4:3 native sensor that provides smooth and stunning images. With this kit, you can capture flying footage with exceptional clarity and detail. Walksnail Avatar HD Nano Kit V3 is suitable for more drones, with 3.1-13V voltage input and 500mw power output, you'll be able to fly various kinds of drones with amazing video quality and range. Nano camera V3 with dimensions of 14*14cm and a weight of only 3g, equipped with a 2.1mm lens and 160° FOV, provides clearer and more realistic image quality. The Avatar VTX comes with 32g built-in storage, it can record 1080p HD and interference-free flight footage without adding an extra SD card and an action camera, reducing the overall weight of the drones and extending the flight time, allowing you to experience a more comfortable flight while recording 1080 HD videos. Canvas Mode: supporting Betaflight, kiss, Inav, Ardu full OSD display and customization, you'll be able to customize various OSD fonts, colors and patterns you like and easily adjust the parameters you want via remote control. Q: Can I use analog channels?/Can I fly with other analog pilots? A: Yes, when you upgrade the firmware to 34.40.15 version, need switch to racing mode. Specifications Camera Model: Avatar HD Nano Camera V3 Image Sensor: 1/3.2-Inch 4Mp 4:3 sensor Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 4:3 native / 16:9 Lens: 2.1mm FOV: 160° Aperture: F2.0 Shutter: Rolling Shutter Min.Illumination: 0.001Lux Weight: 3g (without cable) Dimensions: 14x14x16.8mm Coaxial Cable: 90mm(default)/140mm VTX Model Avatar HD Mini VTX V3 Communication Frequency 5.725-5.850GHz Transmitter Power (EIRP) FCC:<27dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface JST1.0x4(Power in)JST0.8x4(USB) Mounting Holes 25.5x25.5mm(M2 hole);20x20mm(M3 hole) Dimensions 31.5x31.5x9.4mm Storage 32G Recording 1080p/720p Weight 13.4g Operating Temperature -20-40℃ Channels 8 Wide Power Input 3.1V-13V Supported FC System Betaflight; Inav; Fettec; Kiss; ArduPliot OSD Canvas mode Latency Average latency 22ms Antenna 1(IPEX) VTX Antenna Model: Avatar V2 antenna Polarization: LHCP Bandwidth: 5600MHz-6000MHz Average Gain: 1.9dBi VSWR: ≤1.5 Interface: IPEX-1 Line Length: 105mm Dimension: R15x45mm(without cable) Weight: 2g Includes 1x Walksnail Avatar HD Nano V3 VTX Kit w/ Nano Camera 1x 4 Pin USB Cable 1x 4 Pin Power Cable 2x M2x4/5/6mm Screws 4x M2x14mm Screws 4x M2x5x0.5mm washer 5x 2.1x3.4x1mm Gasket 1x 14 to19mm bracket
$108.99
RaceDayQuads Walksnail Avatar HD V2 VTX Module - Choose Version
Spare replacement VTX module for Walksnail HD V2 VTX Combos. Check out all our Walksnail HD products! Includes 1x Walksnail Avatar HD V2 VTX Module
$99.99
RaceDayQuads Walksnail Avatar HD VTX Module
Spare replacement VTX module for Walksnail HD Micro and Nano VTX Combos. Check out all our Walksnail HD products! Includes 1x Walksnail Avatar HD VTX Module
$99.99
RaceDayQuads Walksnail Avatar HD VTX U.FL Antenna 2 Pack
Replacement antenna 2 pack for the Walksnail Avatar VTX Check out all our U.FL VTX antennas and our selection of Walksnail HD products! Specifications Polarization: LHCP Bandwidth: 5.6-5.9GHz Gain: 2dBi Average Radiation Efficiency: >= 98% VSWR: <=1.4 Connector: U.fl Length: 90mm Weight: 1.5g Includes 2x Walksnail Avatar HD VTX U.FL Antenna
$15.89
RaceDayQuads Walksnail Avatar HD VTX U.FL Antenna V2
Replacement antenna for the Walksnail Avatar VTX Check out all our U.FL VTX antennas and our selection of Walksnail HD products! Specifications Polarization: LHCP Bandwidth: 5600MHz-6000MHz Gain: 1.9dBi Average VSWR: <=1.5 Connector: U.fl Length: 105mm Size: R15 X 45mm (without cable) Weight: 2g Includes 1x Walksnail Avatar HD VTX U.FL Antenna V2
$12.89
RaceDayQuads Walksnail Avatar Micro HD FPV Camera V2 w/ Gyro and 14mm Cable
The Avatar HD Micro Camera for the Walksnail Avatar VTX works with Walksnail Avatar and Fat Shark Dominator HD Goggles. Check out all our Walksnail HD products! Features With 2K 120fps pixels and native 4:3 sensor, ensures an excellent picture quality. Additionally, the native 4:3 image ratio provides the advantage of capturing a larger area of the surrounding scenery. The new camera V2 Camera with Gyro supports Gyroflow, Lets you smooth and stabilize your footage. F/2.0 Aperture increases the amount of light, making the picture more sharp and colorful. Comes with a 160° wide-angle FOV. Specifications Image Sensor: 1/3.2-Inch 4Mp 4:3 sensor Resolution: 1080P/60fps; 720P/100fps; 720P/60fps;1080P/120fps compatibility 1080P/100fps compatibility; Ratio: 4:3 native /16:9 Lens: 2.1mm FOV: 160° Aperture: F2.0 Shutter: Rolling shutter Weight: 7.2g Dimensions: 19x19x22mm Coaxial Cable: 140mm Gyroflow supported Includes 1x Walksnail Avatar Micro HD FPV Camera V2 w/ Gyro and 14mm Cable
$58.99
RaceDayQuads Walksnail Avatar Micro HD FPV Camera w/ Cable
The Avatar HD Micro Camera for the Walksnail Avatar VTX works with Walksnail Avatar and Fat Shark Dominator HD Goggles. Check out all our Walksnail HD products! Specifications Image Sensor: 1/27" Resolution: 1080p 60FPS / 720P 120FPS / 720P 60FPS Aspect Ratio: 16/9 and 4/3 Switchable Lens: 2.1mm Field Of View: 170° Aperture: F2.0 Shutter Style: Rolling Shutter Minimum Illumination: 0.001Lux Cable Length: 140mm Dimensions: 19x19x22mm Weight: 6g Includes 1x Walksnail Avatar Micro HD FPV Camera w/ Cable
$58.99
RaceDayQuads Walksnail Avatar Micro HD Pro FPV Camera V2 w/ Gyro and 14mm Cable
The Avatar HD Pro Micro Camera for the Walksnail Avatar VTX works with Walksnail Avatar and Fat Shark Dominator HD Goggles. Check out all our Walksnail HD products! Features 1/1.8 inch Sony Starvis Ⅱ sensor, come with extremely clear night vision as long as day vision. Support 1080P/120fps high frame, the first high frame night vision HD camera in FPV market. Support Gyroflow, takes you a smooth and stabilized video quality. F/1.6 Large Aperture to increase the amount of incoming light, make picture more incomparable. Walksnail Avatar camera V2 has 160° wide-angle FOV. Specifications Image Sensor: 1/1.8-Inch Sony Starvis Ⅱ sensor Resolution: 1080P/60fps;720P/100fps,720P/60fps;1080P/120fps compatibility; Ratio: 16/9; 4/3 Lens: 8Mp FOV: 160° Aperture: F1.6 Shutter: Rolling shutter Min.Illumination: 0.00001Lux Weight: 9.5g Dimensions: 19x19x24mm Coaxial Cable: 140mm Gyroflow supported Includes 1x Walksnail Avatar Micro HD Pro FPV Camera V2 w/ Gyro and 14mm Cable
$64.99
RaceDayQuads Walksnail Avatar Nano HD FPV Camera w/ Cable
The Avatar HD Nano Camera for the Walksnail Avatar VTX works with Walksnail Avatar and Fat Shark Dominator HD Goggles. Check out all our Walksnail HD products! Specifications Image Sensor: 1/27" Resolution: 1080p 60FPS / 720P 120FPS / 720P 60FPS Aspect Ratio: 16/9 and 4/3 Switchable Lens: 2.1mm Field Of View: 170° Aperture: F 2.0 Shutter Style: Rolling Shutter Minimum Illumination: 0.001Lux Cable Length: 90mm Dimensions: 14x14x17mm Weight: 3.5g Includes 1x Walksnail HD Nano Camera
$54.99
RaceDayQuads Walksnail Avatar PRO HD V2 VTX Kit - 32GB with Gyroflow
The Micro Camera and VTX Combo for Fat Shark Dominator HDO3 are provided by WalkSnail. The video transmitter for the Fat Shark Dominator HD Goggles and Walksnail Goggles has arrived! The Walksnail Avatar HD Pro Kit features a VTX with enhanced TVS protection and support for up to 6S. This VTX delivers unmatched stability due to the aid of being equipped with Gyroflow technology. This allows super smooth and stabilized video from your FPV system. The VTX is resistant to GPS interference with a wide input voltage range of 6V to 25.2V. This kit also features 1080P compatibility, high frame starlight, a 4KM range, and 32GB built-in storage option. Enjoy the unparalleled performance and take your FPV adventures to new heights with this cutting-edge technology! Check out all our Walksnail HD products! Features Compatible with FatShark Dominator HD FPV Goggles Canvas mode and distance detection with the dual-antenna system Reliable digital HD video transmission (1080P – H.265 encoding) 1080P 120fps compatibility Sony Starvis Ⅱ Technology Built-in 32GB storage High frame starlight Lightweight design 22ms low latency Ranging Mode 4km range 6V-25.2V FOV 160° VTX Specifications Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP) FCC:<30dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm 1/O Interface: JST1.0x4(Power in)JST0.8x6(USB) Mounting Holes: 25.5x25.5mm; 20x20mm Dimensions: 33.5x33.5x10.5mm Storage: 8G/32G Recording: 1080p/720p Weight: 17.6g Operating Temperature: -20-40℃ Channels 8 Wide Power Input: 6V-25.2V Supported FC System Betaflight; Inav; Fettec; ArduPilot; Kiss OSD Canvas mode Latency: Average delay 22ms Antenna: 1(IPEX) Camera Specifications Resolution: 1080P/60fps;720P/120fps,720P/60fps;1080P/120fps compatibility; Image Sensor: 1/1.8-Inch Sony Starvis Ⅱ Sensor Model: Avatar HD Pro camera Min.Illumination: 0.00001Lux Dimensions: 19x19x24mm Shutter: Rolling shutter Coaxial Cable: 140mm Ratio: 16/9; 4/3 Aperture: F1.6 Weight: 9.5g Lens: 8Mp FOV: 160° Antenna Specifications Polarization: LHCP Bandwidth: 5600MHz-6000MHz. Gain: 1.9dBi VSWR: ≤1.5 Input Impedance: 50Ω Interface: IPEX-1 Size: R15x45mm (without cable) Weight: 2g Includes USB transfer extension cable X1 4 Pin silicone cable X1 M2x4mm screws X8 M2x5mm screws X4 M2x6mm screws X4 M2x14mm screws X4 M2x5x0.5mm gasket X4
$158.89
RaceDayQuads Walksnail Avatar Replacement Coaxial Cable - Choose Version
Spare replacement lens for Walksnail Avatar Nano & Micro Cameras.Available in 9cm and 14cm. The 14cm includes a micro camera back case. Check out all of our Walksnail HD products and FPV Goggles & Accessories at RDQ! Includes 1x Walksnail Avatar Coaxial Cable
$9.89
RaceDayQuads Walksnail Avatar Replacement Lens - Choose Version
Spare replacement lens for Walksnail Avatar Nano & Micro Cameras.Be sure to choose the correct size for your camera! Check out all our replacement lenses and our Walksnail selection! Specifications Lens: 2.1mm Field Of View: 170° Aperture: F 2.0 Includes 1x Walksnail Avatar Replacement Lens - Choose Version
$9.89
RaceDayQuads Walksnail Avatar Replacement USB Cable
Spare replacement USB cable for use with Walksnail Avatar VTXs. Check out all our Walksnail HD products! Includes 1x Walksnail Avatar Replacement USB Cable
$6.89
RaceDayQuads Walksnail Avatar Replacement VTX Power Cable
Spare replacement power cable for use with Walksnail Avatar VTXs. Check out all of our Walksnail HD products and FPV Goggles & Accessories! Includes 1x Walksnail Avatar Replacement VTX Power Cable
$2.99
RaceDayQuads Walksnail Avatar VRX Combo - Choose Version
Lightweight design, ultra-thin experience The Walksnail Avatar VRX Kit Combo is only 83g and comes with 114x55x22mm; a size easy to carry. Walksnail VRX adopts a 4-antenna design. 2 directional antennas and the maximum transmission distance is 4km 1080P/60FPSWalksnail VRX adopts industry-leading H.265 encoding technology,which can provide a minimum delay of 22ms and a maximum resolution of 1080p.The HD picture quality takes you to experience the fun of flying a drone. HDMI output ensures you enjoy uncompressed audio and video signals from the Walksnail HD system Canvas ModeSupports Betaflight, INAV, and KISS with full OSD. You can easily adjust the parameters you want by remote control. Specification Camera: Model Avatar nano/Avatar cameraImage Sensor: 1/2.7”1nchResolution: 1080P/60fps,720P/120fps,720P/60fpsRatio: 16/9 4/3Lens: 2.1mmFOV: 170°Aperture: F2.0Shutter: Rolling shutterMin.Illumination: 0.001LuxWeight: 3.5g/6gDimensions: 14x14x17mm/19x19x22mmCoaxial Cable: 90mm/140mm VTX: Model Avatar moduleCommunication Frequency: 5.725-5.850GHzTransmitter Power: (EIRP) FCC:<30dBm;CE:<14dBm;SRRC:<20dBm;MIC: <25dBmI/O Interface: JST1.0x6 (Power in) JST1.0x4(USB)Mounting Holes: 25.5x25.5mmDimensions 33x33x9.5mmStorage: 8GBRecording: 1080p/720pWeight: 16gOperating Temperature: -20-40℃Channels: 8Wide Power Input: 6V-25.2VSupported FC System BetaflightOSD Canvas modeLatency Average Delay: 22msAntenna: 2x (IPEX)Goggles Antenna Model: Red birdPolarization: LHCPBandwidth: 5.6GHz-6.0GHZAverage Gain: 1.9dBiRadiation Efficiency: ≥97%VSWR: ≤1.3Cross-Polar Rejection: -15to-30dBConnector: RP-SMADimension: H24.8mm x R15.3mmWeight: 4.2gAvatar HD VRX Model Avatar HD VRXCommunicationFrequency: 5.725-5.850GHzTransmitterPower: (EIRP) FCC:<30dBm;CE:<14dBm;SRRC:<20dBm;MIC:<25dBmI/O Interface: HDMI, micro SD card slot, DC5.5x2.1mmHDMI output: 1080p/60fps, 720p/100fps, 720p/60fpsPower Input: 7-21V(2S-5S)SD Card Support:256GSystem: Avatar HD system Includes: Avatar VRX:RedBirdAntenna x2HDMI cable x12-in-1 DCPowerCable x1 PLUS one of the following based on option picked above Avatar HD Nano KIT: (or buy alone)4 Pin USB Cable x16 Pin Power Cable x1M2x3/4/5mm Screws x2M1.2x1.5mm Screws x214-19mm Bracket x1 Avatar HD Micro KIT: (or buy alone)4 Pin USB Cable x16 Pin Power Cable x1M2x3/4/5mm Screws x4M1.2x1.5mm Screws x2 Avatar Mini 1S KIT: (or buy alone)4 Pin USB Cable x16 Pin Power Cable x1M2x3/4mm Screws x2M2x16mm Screws x4M2 Screw nut x42.1x3.4x1mm Gasket x5 Avatar Micro 8GB KIT: (or buy alone)USB transfer extension cable X14 Pin silicone cable X1M2x4mm screws X8M2x5mm screws X4M2x6mm screws X4M2x14mm screws X4M2x5x0.5mm gasket X4 Avatar Micro 32GB KIT: (or buy alone) USB transfer extension cable X14 Pin silicone cable X1M2x4mm screws X8M2x5mm screws X4M2x6mm screws X4M2x14mm screws X4M2x5x0.5mm gasket X4 Avatar PRO KIT 32GB: (or buy alone)USB transfer extension cable X14 Pin silicone cable X1M2x4mm screws X8M2x5mm screws X4M2x6mm screws X4M2x14mm screws X4M2x5x0.5mm gasket X4 Q&A: Q: Is VRX compatible with goggles from other products?A: Compatible With Analog Goggles, HDMI Out(Our VRX module supports HDMI out, if your glasses support HDMI in it should work)Q: Do I need a set of goggles with a 1080p resolution or is 720p is enough?A: VRX supports 720P\1080PQ: Avatar HD Micro kit come with a 140mm cable between the VTX and camera?A: yesQ: Does the Pre-sale unit fit a 20x20 mount?A: Our VTX is 25x25Q: The difference between all 3 of the Walksnail kits? What is the Avatar 1s vs Avatar HD micro vs Avatar HD nano?A:The Mini 1s kit:350mw, Power Input: 3.1V-5V, VTX Weight 6.8gAvatar HD micro/nano kit standard version:1200mw, Power Input: 6V-25.2V, VTX Weight: 16gQ: Micro/Nano Camera difference?A:Weight:3.5g/6gDimensions:14x14x17mm/19x19x22mmCoaxial Cable:90mm/140mm
$218.99
RaceDayQuads Walksnail WS-M181 GPS
Because the GPS chip is a new 10th generation chip, the flight controller needs to flash firmware 4.29 and above, and the firmware below 4.29 uses the NMEA protocol. Walksnail WS-M181 GPS made for the Walksnail Avatar VTX and Walksnail HD system. Check out our other GPS options, as well as the rest of our Walksnail HD products! Features With its small size, light weight, fast positioning, and stable connection. It is suitable for FPV, RC airplane, quadcopter and others to enhance the users flight experience. Featuring the u-blox M10 platform UBX-M10050 GNSS chipset and BUILT-IN QMC5883 MAG, the module offers stronger performance and more accurate positioning. The ultra-thin ceramic antenna uses a special spray painting process to prevent oxidation and scratching, ensuring consistent positioning performance. The built-in battery can realize hot start and realize positioning quickly. It offers six positioning modes, providing more flexible combinations (default GPS + GLONASS + BDS multi-mode positioning).The measured maximum number of search stars can cover 32pcs. Specifications Chip: M10 (ten generation chip) Frequency: GPS L1,GLONASS L1,BDSB1,GALILEO E1,SBAS L1.QZSS L1 Power: 5V Size: 18mmx18mmx4.6mm Antenna: ceramic antenna (oil spraying process, prevent scratching and oxidation) Receiving channels: 72 search channels Compass: QMC5883 Baud rate: 115200dps Output protocol: NMEA UBLOX (dual protocol) Output frequency: 1Hz-10Hz, Default 10Hz Speed accuracy: 0.05m/s Horizontal positioning accuracy: 2D ACC1.5m(open air) Trace-162dBm Capture -160dBm Altitude: 50000m Speed: 500m/s Acceleration: 4G Operating temperature: -40℃-+85℃ Storage temperature: -40℃-+105℃ Includes 1x Walksnail WS-M181 GPS
$16.99