The Aikon AKC 70A 8-in-1 8S continues Aikon's pursuit of excellence! This ESC provides Aikon's proven quality and durability with 8 high current rated ESCs in one package that supports a supply voltage up to 8S. This is the perfect ESC for cinematic ocotocopter configurations.
Make sure to check out our other ESCs and entire line of Aikon gear!
Features
STM Electronics STM32G071 ARM® Cortex® M0+
8 ESCs in one package for compact octocopter builds
Top grade MOSFET 5x6mm package
Universal 30x30mm mount holes
Specifications
Battery: 2-8s
Constant Current: 70A
Burst Current: 80A
Mount Hole: 30x30mm
Firmware: BLHeli32
MCU: STM32G071
Bootloader: Yes
Weight( with wire): 25g
MOSFET Size: 5x6
Includes
1x Aikon AKC70 BL32 70A 3-8S 30x30 8in1 ESC
The Aikon flight controller is a new generation flight controller designed specifically to work with our Aikon 8-in-1 ESCs. We've packed all the greatest features into one seamless flight experience.
Check out all our 30x30 FCs, our DJI compatible gear section, and all our Aikon gear!
Features
216mhz F7 processor
5 Software invertible hardware UARTS
Onboard OSD and blackbox
Software controlled VTX power switch (assigned to USER1 mode by default)
LED and buzzer outputs (LED input doubles as PPM)
Quick connection cable for 8-in-1 ESCs
Quick connection cable for DJI HD system
On-board high overhead voltage regulators rated up to 6S (50v peak to handle voltage spikes)
10v 1.5A voltage regulator for DJI HD system
USB Type C connector for easy programming
Specifications
Battery: 2-6s
Mount Holes: 30.5x30.5mm
Firmware: Betaflight AIKONF7 Target
MCU: STM32F722
IMU: BMI270 (Interrupt pin connected)
Blackbox: SPI 16MB
Motor Outputs: Up to 8
Weight: 12g
Includes
1x Aikon F7 3030 V2.2 HD 30x30 Octo Flight Controller
This FC pairs seamlessly with any Aikon ESC. The F7 MCU will allow you to dial in your tune the way you want it and the DJI plug and play means it's ready to go with the Air Unit or Vista.
Check out all our 20x20 FCs, our DJI compatible gear section, and all our Aikon gear!
Features
216mhz F7 processor
5 Software invertable hardware UARTS
Onboard OSD and blackbox
Software controlled VTX power switch
LED outputs
Quick connection cable for 4-in-1 ESCs
On-board high overhead voltage regulators up to 6S (50v peak for voltage spikes)
10V/1.5A regulator for DJI HD system
DJI Quick Connect Port
Specifications
Input Voltage: 2-6s
Mount Hole: 20x20mm
Betaflight Target: AIKONF7
MCU: STM32F722RET6
IMU: BMI270
Blackbox SPI: 16MB
Weight: 8g
Includes
1x Aikon F7 Mini V3 HD 20x20 Flight Controller for DJI
Wiring Diagram
Can be used with any 8 pin stacks, just make sure to re-pin when necessary!
Specifications
Length: 72mm end to end
Includes
1x Airbot 4in1 ESC to Flight Controller 8 Pin Cable Replacement for Bardwell & Ori32
The G4 features Betaflight compatibility and is the first of its kind. It contains 4 35A AM32 ESCs, 6S max and the QF32MTF4AK8U7 on the AIO board, creating a more compact design. Two voltage regulators – a 5V and 10V, both rated for 2.5A – are included. The 10V one can power the VTX & DJI O3 Air Unit, while the 5V one can power the LEDs, peripherals, etc. The STM32G47X MCU, ICM-42688p gyro, 16MB Data Flash, DSP310 baro, 16 RGB LEDs, and plug solutions for digital video complete the package.
A new feature is the ultra-hydrophobic nano waterproof coating. This coating allows air to pass through while avoiding water, giving extra protection from moisture and other elements.
Important note: When trying to get the HD OSD working, it's required that both ground pins out of the DJI port are not soldered to the VTX.
Check out our other AIO flight controllers, as well as the rest of our Airbot selection!
Features
Superhydrophobic Nano Waterproof Coating
Onboard 16 RGB LEDs can be programmed
ESC has a F4 MCU, runs AM32 firmware, capable of 6S and is rated at 35Amps
10V BEC for DJI O3 Air Unit
Specifications
MCU: STM32G473, 512KB Flash
BEC: 5V 2.5A + 10V 2.5A
Blackbox: 128Mbit, 16MB
Gyro: ICM-42688
Barometer: DSP310
ESC: F4 MCU, run AM32 firmware, 6S 35Amps
OSD: AT7456
4x Uarts
1x 12C
Weight:10.4g
Mounting pattern：25.5x25.5mm
Connector Pinout:
SDA, SCL, DN, DP, GND, 5V, L-RX1, L-TX1 is for External USB/GPS Connector
TX2, GND, RX1, TX1, GND, 10V is for VTX Connector
Wiring Diagram
- Information was referenced from a review of the Airbot Fenix G4 AIO board brought to you by VitroidFPV.
The Airbot OpenLager gives the capability of black box recording to any drone that doesn't have it. This is fantastic for tuning and finding issues in your system.
This device needs to be flashed with updated firmware before use. Follow the simple instructions in the wiring & info tab.
Check out our other flight controller accessories, as well as the rest of our Airbot selection!
Features
It's faster than an average black box with a 4 bit SD interface clocked at 19.2MHz with DMA.
It has buffer memory to ride out times when the SD card is busy (125kbytes with the current firmware)
It fits in a smaller form factor builds with ease.
ESD protection on input pins.
And it has a flip-up microSD connector that is better at retaining the card in crashes and hard landings.
Specifications
Dimensions: 20x15mm
Weight: 2g
Includes
1x Airbot OpenLager Blackbox
Wiring & Info
The OpenLager is easy to use with async serial. First, wire according to the diagram below (an example of an OpenPilot-style connector is in the drawing). Note that you should attach the flight board's TX to Openlager's RX pin!
OpenLager has an onboard regulator and can be powered with 3.3-5.5V (the regulator dropout voltage is low enough that the SD card will still work properly at 3.3V input).SD CARD MUST BE FAT16 OR FAT32 FORMAT. FIRMWARE MUST BE UPDATED BEFORE USING:
Format your SD card. It must be either FAT or FAT32 format (SanDisk Extreme Pro 8GB recommended)
Put the firmware lager.bin file into the sdcard and insert into the OpenLager
Power on. The RED led should blink for several seconds. Wait until the RED led is stops blinking and continue to wait 10s more.
Power off
Format the SD card again
Insert the SD card into OpenLager and power on.
Power off; remove the card, and attach it to your computer. You'll find openLager has written a file to it called lager.cfg:
{ "startupMorse" : "", "useSPI" : false, "baudRate" : 2000000, "preallocBytes" : 104857600, "preallocGrow" : false}
The important field to change is baudRate -- set it to the speed of the serial you'll be using for logging. dRonin supports 115200, 250000, 1500000, 2000000, and 2470000 bits per second. Cleanflight prefers 250000 bits per second, etc.
The green LED is on always when power is applied, and the red LED blinks with activity when the card is writing. After 200ms of inactivity, the buffers on openLager will be forcibly flushed. If power is suddenly removed, the file may not be completed in the filesystem; this can be changed by setting preallocGrow to 'true' at the possible cost of garbage being present at the end of the file in this scenario.
The firmware for openlager may be updated by putting an appropriate firmware image called lager.bin on the card.
Featuring a whoop camera with Smart Audio! Take your Whoop tech to the next level.
Check out all our Camera/VTX AIOs & Combos
Features
Super light weight: 4.3g, all in one vtx + camera + antenna
One button frequency and power setup
Support 0.01mW parameter-adjusting mode
0.01/25mW/50mW/100mW/200mW power switchable
OSD configuration using FC Uart (F3/F4/F7 with OSD)
Notice: 5645,5925,5945(E4,E7,E8) channels are not available due to FCC regulation.
Specifications
Input voltage: 3.2-5.5V
Weight: 4.3g(exclude antenna)
Frequency: 5.8GHz 5 bands 40 channels
Includes
1x AKK AIO-SA Whoop/Micro AIO FPV Camera & 25-200mW VTX w/ Smart Audio
The AKK FX3 Ultimate is essentially the mini version of the AKK FX2. With a 20x20 profile, it can easily fit into any of your 20x20 builds while having a high max output power and Smart Audio capability.
Details:
Support Pit Mode
25mW, 200mW, 400mW and 600mW power switchable
One button frequency and power setup
OSD configuration using Smart audio
7-24V input with 5V output
MMCX+UFL connector
MIC
Note: Smart Audio is not compatible with KISS flight controllers.
FPV REGULATORY NOTICE
The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. RDQ cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.
in AKK's newest VTX which has built-in DVR, Smart Audio, up to 6s (7 - 26v) direct Lipo input, adjustable power output (25, 200, 600 & 1000 mW) w/ pit mode, and a 5v cam power output.
Check out the rest of our selection of VTX's!
Specifications
Brand name: AKK
Item name: Infinite DVR VTX
Input voltage: 7V to 26V
Extra features: Smart audio DVR
Power supply: 5V output for camera
Output power: 25/200/600mW/1000mW
Antenna connector: MMCX
Cable connector: Solder pads
Records Video Size: VGA (640*480)
Max Support TF Card: 32G
Dimension: 36x36mm, 30.5 stackable hole
Weight: 8.8g (excluding antenna)
Features
Support Smart audio
25/200/600/1000mW power switchable
One button frequency and power setupOSD configuration using smart audio
7-26V input with 5V output for camera
With MIC
Notice: 5645/5925/5945 (E4/E7/E8) are not available due to FCC regulation. Selecting 5645/5925/5945 (E4/E7/E8) will be invalid action.
Note: 37 channels are all above 5650 and below 5925MHz, which are legal to use in the USA with an amateur radio license.
This equipment is being sold under FCC’s amateur radio rules.
Operators must require amateur radio license to operator legally in
the US. Use of amateur equipment without a license or use of
equipment on restricted frequencies could subject the operator to
significant fines by the FCC.By purchasing this equipment, the user is
agreeing that they understand these responsibilities and will operate
the equipment legally. More information related to ARL, please go to
http://www.arrl.org/getting-licensed.Pacakge Included:
1x VTX
1x pigtail
1x cable
FPV REGULATORY NOTICE
The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your area. It is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. RDQ cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.
This is a great and quick "solder n' go" product if you need a capacitor for your quad. The capacitor and pigtail come pre-soldered together and all you need to do is solder the 14 AWG leads to your quad.
Check out our other tools and building supplies and all our Capacitors!
Specifications
Wire: 14 AWG
Wire Length: 100MM(measured from pcb)
Capacitor: 25V 2200uF, 35V 1000uF, 35V 2200uF
Connector: Yellow XT60
Weight: 13-17g
Includes
1x All-in-One Capacitor and XT60 Pigtail Combo
Typically used to connect a device with female a XT60 plug to a DC power supply, lead acid, SLA, or Pb field battery using Alligator clips.
Check out our selection of chargers and accessories and our pigtails and adapters!
Specifications
Wire Gauge: 14 AWG
Length: 250mm (10")
Includes
1x Alligator Clips to XT60 Male Adapter Cable
This socket mount will hold a male XT60 securely against carbon meaning you now have more options for safely mounting your power leads! The mounting hole distance is 20mmMale XT60 Not Included.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Specifications
Mounting Pattern: 20mm, M2.5
Includes
1x Aluminum XT60 Surface Mount Bracket
2x M2.5 Screw
These handy little connectors are basically 3 pin XT30s, They can be used on ESCs, motors, or anything with 3 wires to allow for quick connections and part swaps.
Check out all our pigtails, adapters and connectors!
Features
Suitable for connecting ESCs and motors
With protective sleeve
Assistive weld foot, more stable
Specifications
Body Material and Surface Plating: Brass and gold plated
Insulation Material: PA66
Original Internal Resistance: 0.8MΩ
500 Times Internal Resistance: 0.85MΩ
Max. Continuous Current: 30A (within 30 minitues)
Max. Instantaneous Current: 40A (within 1 minitues)
Recommended Cable Spec: 18AWG 2.8mm diameter
Recommended Soldering Spec: 400° C/3S
Weight: 1.2g/pcs
Insulation Degree: UL94V-0
Machine Life: 3000 Times
Includes
1x AMASS MR30 Connector Male w/ Protective Shield
1x AMASS MR30 Connector Female w/ Protective Shield
These handy little connectors are basically 3 pin XT60s, They can be used on ESCs, motors, or anything with 3 wires to allow for quick connections and part swaps.
Check out all our pigtails, adapters and connectors!
Features
Suitable for connecting ESCs and motors
With protective sleeve
Assistive weld foot, more stable
Specifications
Body Material and Surface Plating: Brass and gold plated
Includes
1x AMASS MR60 Connector Male w/ Protective Shield
1x AMASS MR60 Connector Female w/ Protective Shield
These handy little connectors are basically 3 pin XT60s, They can be used on ESCs, motors, or anything with 3 wires to allow for quick connections and part swaps.
Check out all our pigtails, adapters and connectors!
Features
Suitable for connecting ESCs and motors
With protective sleeve
Assistive weld foot, more stable
Specifications
Body Material and Surface Plating: Brass and gold plated
Includes
1x AMASS MT30 Connector Male w/ Protective Shield
1x AMASS MT30 Connector Female w/ Protective Shield
These XT150 connector sets are ideal for large batteries, ESC, or motors! The durable nylon material is less likely to experience damage than other connectors and works well with up to 150 amps of current.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Features
Nylon material holds 150A current for extended periods without exceeding 80 Degrees.
Male connectors use a collet-style spliced contact area.
Dovetail linking.
Easy to solder.
Specifications
Max Amps: 150
Diameter: 6mm
Connection Type: Male or Female
Includes
1x AMASS XT150 w/ 6mm Gold Connector - Choose Version & Color
This genuine Amass connector is an ideal option for safely and securely mounting your power leads. Amass is known for their quality and there is no exception with this connector.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Specifications
Plating: Brass and Gold
Mounting Pattern: 20mm, M2.5
Includes
1x Amass XT60E1 Male
Premium Amass XT60H connector for when the classic XT60 just won't cut it. The snap on cover for the wire side of the connector means no need for heat shrink.
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Includes
1x Amass XT60H Connector - Male or Female
These genuine Amass XT90H connectors are perfect for those that like to go big with their builds. If you need a connector that can to handle a lot of current, the XT90 will do the job with ease!
Choose male or female, and your color preference!
Check out all our pigtails, connectors and adapters, and all our soldering supplies while you're at it!
Specifications
Plating: Brass and Gold
Includes
1x Amass XT90 H Connector
Upgrade your racing drone with the AMAXinno Competition 2207 1950Kv Motor. Built for speed and agility, this motor delivers powerful performance and precision control. Take your racing to new heights and leave the competition in the dust.
Check out all our brushless motors and the entire AMAX selection!
Specifications
KV: 1950
Motor Mounting: M3 16x16
Shaft Size: 5mm
Stator diameter: 22mm
Stator height: 7mm
Configuration: 12N14P
Peak power (10S): >1000W
Cable length: 150mm
Weight with cables: 35g
Weight without cables: 31.5g
Includes
1x AMAXinno Competition 2207 1950Kv Motor
1x M5 Self-Locking Nut
4x M3x8mm Screw
Upgrade your racing drone with the AMAXinno Competition 2306 1950Kv Motor. Built for speed and agility, this motor delivers powerful performance and precision control. Take your racing to new heights and leave the competition in the dust.
Check out all our brushless motors and the entire AMAX selection!
Specifications
KV: 1950
Motor Mounting: M3 16x16
Shaft Size: 5mm
Stator diameter: 23mm
Stator height: 6mm
Configuration: 12N14P
Peak power (10S): >1000W
Cable length: 150mm
Weight with cables: 33.5g
Weight without cables: 30.0g
Includes
1x AMAXinno Competition 2306 1950Kv Motor
1x M5 Self-Locking Nut
4x M3x8mm Screw
Upgrade your racing drone with the AMAXinno Competition 2207 1950Kv Motor. Built for speed and agility, this motor delivers powerful performance and precision control. Take your racing to new heights and leave the competition in the dust. The Bando version takes the same design and performance but with a tougher bell construction intended for those who fly and crash over hard surfaces.
Check out all our brushless motors and the entire AMAX selection!
Specifications
KV: 1950
Motor Mounting: M3 16x16
Shaft Size: 5mm
Stator diameter: 22mm
Stator height: 7mm
Configuration: 12N14P
Peak power (10S): >1000W
Cable length: 150mm
Weight with cables: 37g
Weight without cables: 33.5g
Includes
1x AMAXinno Competition Bando 2207 1950Kv Motor
1x M5 Self-Locking Nut
4x M3x8mm Screw
Upgrade your racing drone with the AMAXinno Competition 2306 1950Kv Motor. Built for speed and agility, this motor delivers powerful performance and precision control. Take your racing to new heights and leave the competition in the dust. The Bando version takes the same design and performance but with a tougher bell construction intended for those who fly and crash over hard surfaces.
Check out all our brushless motors and the entire AMAX selection!
Specifications
KV: 1950
Motor Mounting: M3 16x16
Shaft Size: 5mm
Stator diameter: 23mm
Stator height: 6mm
Configuration: 12N14P
Peak power (10S): >1000W
Cable length: 150mm
Weight with cables: 35g
Weight without cables: 31.5g
Includes
1x AMAXinno Competition Bando 2306 1950Kv Motor
1x M5 Self-Locking Nut
4x M3x8mm Screw
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1750
Input Voltage: 4-6S
Motor Height: 16.5mm
Stator Dimensions: Φ22x7mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 28.1g
Includes
1x AMAX Performante A-Bell 2207 1750Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 2550
Input Voltage: 3-4S
Motor Height: 16.5mm
Stator Dimensions: Φ22x7mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 28.1g
Includes
1x AMAX Performante A-Bell 2207 2550Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1750
Input Voltage: 4-6S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 1750Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 1950
Input Voltage: 4-6S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 1950Kv Motor
AMAX Motors are back with a special half-hollow shaft and further improved "A-Bell" design, making slipped magnets and dented bells a thing of the past! Smooth, powerful and extremely durable!Check out all our brushless motors and the entire AMAX selection!
Features
Half-hollow shaft is for strength and light weight
Fully encased magnets in the new A-Bell design
Wave structure on bell for enhanced cooling and robustness
Specifications
Kv: 2550
Input Voltage: 3-4S
Motor Height: 15.4mm
Stator Dimensions: Φ23x5.5mm
Output Shaft Dimensions: M5
Wire Dimensions: AWG x 150mm
Mounting Pattern: 16x16mm
Weight (w/o wires): 23.9g
Includes
1x AMAX Superleggera 2305.5 2550Kv Motor
Revised version now includes a power switch and additional solder pads.The Analog FPV FatShark Module Adapter V2 for DJI Digital FPV Goggles fits so well you can use a fat shark or various third-party fat shark style analog video receivers modules! It transfers video and audio signals to the high-quality screen of DJI FPV goggles for viewing or recording. This compact and lightweight adapter is easy to install and won't void your warranty! Check out all our DJI compatible frames, electronics & accessories and our FPV receiver modules & antennas collection!Specifications
Input Voltage: 2S-4S (DC5.5x2.1mm)
Internal Voltage: 5V 3A (with pad output)
Output Voltage: 2S-4S (DC 5.5x2.1mm)
Signal Input: Standard Fat Shark Receiver Port
Including third-party receivers: Realacc, Furious, etc.
Signal output: standard audio / video
Power Switch
Dimension: 48x28x12mm
Weight: 10g (without extension cable)
Includes
1x Analog FPV Adapter for DJI Goggles
1x Adapter mounting board and screws
1x Audio and video cable
1x Power cable
Wiring Diagram
V3 now includes a voltage display, power switch and additional solder pads.This analog fat shark module adapter fits on the side of your DJI Digital FPV Goggles so you can use a fat shark or various third-party fat shark style analog video receivers modules! It transfers video and audio signals to the high-quality screen of DJI FPV goggles for viewing or recording. This compact and lightweight adapter is easy to install and won't void your warranty! We also have the V2 Adapter if you don't need the voltage display. Seen below installed in the Aluminum Case we carry specifically for this device:Check out all our DJI compatible frames, electronics & accessories and our FPV receiver modules & antennas collection!
Specifications
Input Voltage: 2S-4S (DC5.5x2.1mm)
Internal Voltage: 5V 3A (with pad output)
Output Voltage: 2S-4S (DC 5.5x2.1mm)
Signal Input: Standard Fat Shark Receiver Port
Including third-party receivers: Realacc, Furious, etc.
Signal output: standard audio / video
Dimension: 55x28x12mm
Weight: 13g (without extension cable)
Includes
1x Analog FPV Adapter V3 for DJI Goggles
1x Adapter mounting board and screws
1x Audio and video cable
1x Power cable
1x Allen Key
Wiring Diagram
This 3D printed antenna holder attaches to any standoff, making antenna mounting a breeze!
Check out all our 3D printed accessories!
Includes
1x Antenna Holder/Mount for Standoff - 3D Printed TPU
Micro strap suitable for the Armattan Tadpole frame and other micro quads.
Check out the rest of our battery straps and all our Armattan products!
Includes
1x Armattan Micro Anti-Slip Battery Strap
Coated with a white rubber so that your battery will not slip out of place easily. Now with a metal buckle for extra strength.
Check out the rest of our battery straps and all our Armattan products!
Includes
1x Armattan 250mm Battery Strap w/ Metal Buckle
Small dog bone shaped landing pads for various Armattan frames.
Check out the rest of our Armattan products!
Specifications
Size: 2cm L x 1.2cm W x 1.2cm H
3M Adhesive
Includes
1x Armattan 3M Dog Bone Foam Landing Pads - 4 Pieces
Rubber antenna mount for the Armattan Beaver 5" frame.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Armattan Beaver 5" Rubber Antenna Mount
TPU antenna mount for the Armattan Beaver 5" frame.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Armattan Beaver 5" TPU Antenna Mount
All Armattan warranty claims must be handled directly through Armattan. Please follow this link with instructions on how to file for a warranty claim. https://armattanquads.com/warranty-claims/
After many designs and prototypes, the Armattan Beaver Frame 5" Quadcopter Frame Kit is here! The Armattan Beaver features a strong carbon frame with thicker arms than previous versions which makes it the strongest to date. This frame focuses on noise reduction, easy maintenance, and versatility for use with a variety of electronics. With a weight of 126g, this frame is lighter than previous Armattan frames.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Features
Ease of maintenance: Only one bolt needs to be removed to replace an arm at the field
Well-balanced frame (strength and weight distribution)
Great price point for a high-end, freestyle frame
Thicker arms than any other previous frame
Light and small camera cage
Easy to tune for newcomers
Strong, stiff and light frame
Crash-protection provisions
Good-looking frame
Lifetime warranty
Noise reduction
Versatile
Specifications
Stack Mounting: Two 30.5x30.5mm stacks(center and rear) + Two 20x20mm stacks (4 possible positions)
FPV Camera Mount: 20mm(DJI) or 19mm Micro cam
Motor Mount Pattern: 16x16 or 16x19 or 19x19mm
Warrantied Parts: All CF and alumi frame parts
Main Plate Thickness: 2.5mm
Frame Shape: Compressed X
Frame Weight: 126 grams
Max Stack Height: 25mm
Motor to Motor: 235mm
Arm Thickness: 5mm
Includes
Carbon Fiber
1x 2mm bottom plate
1x 2.5mm main plate
4x 5mm arms 5 inch
1x 2mm top plate
1x 4mm arm core
Hardware
4x M3 25mm profiled alumi standoff
5x M3 20mm button head iron bolt
6x Aluminum cone spacer orange
5x M3 6mm nylon standoff F/F
20x M3 6mm 12.9 grade bolt
5x M3 10mm 12.9 grade bolt
5x M2 2.5mm cup head bolts
2x M3 20mm alumi standoff
9x M3 12mm cup head bolt
3x M3 16mm cup head bolt
5x M2 18mm cup head bolt
5x M2 nylon washer
14x M3 nylon nuts
5x M2 nylock
Metal
1x Right aluminum cam brace orange
1x Left aluminum cam brace orange
2x Aluminum tail posts orange
2x Aluminum cam saver black
Foam
4x Dog bone landing pads
1x Air unit foam
1x Center foam
1x Lite grip
Accessories
1x 25cm clear heat-shrink 20mm wide
4x Motor wire extension PCB
1x Universal antenna mount
2x White lipo strap
Replacement arm for the Armattan Beaver 5" frame.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Spare Beaver 5" Arm
Replacement arm core for the Armattan Beaver 5" frame.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Spare Beaver 5" Arm Core
Replacement bottom plate for the Armattan Beaver 5" frame.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Spare Beaver 5" Bottom Plate
All Armattan warranty claims must be handled directly through Armattan. Please follow this link with instructions on how to file for a warranty claim. https://armattanquads.com/warranty-claims/
Replacement part for the Armattan Beaver 5" Frame, pieces go missing or break when you choose fun over risk, so we got you covered with this replacement center foam.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Armattan Beaver 5" Replacement Center Foam
Replacement main plate for the Armattan Beaver 5" frame.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Spare Beaver 5" Main Plate
Replacement top plate for the Armattan Beaver 5" frame.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Includes
1x Spare Beaver 5" Top Plate
All Armattan warranty claims must be handled directly through Armattan. Please follow this link with instructions on how to file for a warranty claim. https://armattanquads.com/warranty-claims/
Introducing the Armattan Bobcat. 4 inch models are making a come back on the FPV scene. This frame supports a Vista, DJI air unit and DJI O3 Air Unit. This frame can become a compressed X frame or a True X frame depending on how you install the arms. A one of kind frame, brought you by the master frame makers at Armattan.
Check out the rest of our 4" frames, as well as the rest of our Armattan selection!
Features
Dual arms configurations
Front and Rear stack mounting
Re-designed camera cage making it lighter and stronger
Specifications
Frame Weight: 57 grams
Motor to Motor: 182mm (Compressed X)
Motor to Motor: 200mm (True X)
Frame Shape: True X or Compressed X (Modular)
Main Plate Thickness: 2.5mm
Arm Thickness: 3mm
Motor Mount Pattern: 12x12 or 9x9mm
Stack Mounting: Dual M3 20x20mm & M2 16x16mm
FPV Camera Mount: 20mm(DJI) or 19mm Micro cam
Max Stack Height: 20mm
Includes
1x Armattan Bobcat HD 4" Frame Kit
2x Cam Brace
2x Anchor
2x Tail Post
4x Arms 4 inch
1x Center Plate
1x Top Plate
2x Camera Mounting Plate
2x Tie Plate
1x M3 12mm cage standoff
2x M2 20mm cage standoff
5x M2 8mm cup-head bolt
3x M3 12mm button-head bolt (12.9 grade)
3x M3 8mm button head bolt (12.9 grade)
10x M2 6mm cup-head bolt
12x M3 9mm button head bolt
15x M3 sunk nuts
5x M3 20mm bolts
10x M3 nylon nuts
5x M3 6mm nylon standoffs
5x M2 18mm cup-head bolt
5x M2 aluminum nylocks
5x M2 nylon washer
5x M2 metal washer
3x M3 8mm cup-head bolt CW
1x Oomph spacer
2x Lipo strap
1x Top Lite Grip (gel & adhesive foam hybrid pad)
1x Air unit double sided adhesive foam bits
2x Dog-bone landing pads (cuts into 6 pieces, two center pieces can be used as spares)
1x Molded rubber antenna holder
All Armattan warranty claims must be handled directly through Armattan. Please follow this link with instructions on how to file for a warranty claim. https://armattanquads.com/warranty-claims/
Replacement part for the Armattan Bobcat 4", pieces go missing or break when you choose fun over risk, so we got you covered with this replacement aluminum cam brace.
Check out the rest of our 4" frames, as well as the rest of our Armattan selection!
Includes
1x Armattan Bobcat HD 4" Replacement Aluminum Cam Brace
Replacement part for the Armattan Bobcat 4", pieces go missing or break when you choose fun over risk, so we got you covered with this replacement arm.
Check out the rest of our 4" frames, as well as the rest of our Armattan selection!
Includes
1x Armattan Bobcat HD 4" Replacement Arm (1pc)
