SE010-0166-03, Castle Creations Copperhead 10 Waterproof 1/10 Sensored Combo w/1406 (6900Kv) (On-Road Edition) The Castle Creations Copperhead 10 Waterproof 1/10 Sensored "On-Road Edition" Combo provides 1/10 scale enthusiasts of all disciplines with a powerful and performance driven ESC that is packed with features. The Copperhead 10 is an affordable option that sits directly in the middle of the Sidewinder 4 entry-level upgrade ESC and the extreme performance MAMBA X option. The Copperhead 10 utilizes CRYO-DRIVE technology, sensored motor support and data logging to deliver Castle’s signature performance and reliability. Whether crawling the rocks, bashing in the backyard or ripping up the local skatepark, Copperhead 10’s versatility will appeal to a wide variety of 1/10 scale enthusiasts. This combo includes a Castle 1406-6900Kv sensored motor. The 1406-6900kv motor is a great upgrade for 1/10th scale on-road cars for 2s use. It can also be used in some lighter off-road 1/10th stadium trucks and buggies with conservative gearing. NOT for use in 2WD or 4WD short course trucks. NOTE: Not compatible with Castle Field Link program card (CSE010-0063-00). Features: CRYO-DRIVE™: CRYO-DRIVE™ technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs. COOLER TEMPS mean LONGER RUNS and MORE POWER in a COPPERHEAD 10 setup.  DATA LOGGING LITE: Battery Voltage, Battery Ripple, Controller Temperature, Motor RPM and Motor Temperature data points can be captured, downloaded and analyzed via Castle Link software. While not a full version of Data Logging capabilities that the MAMBA X EXTREME 1:10 SCALE ESC has, these critical parameters are excellent sources of information for maximizing performance and battery life of the COPPERHEAD 10.  SMARTSENSE™ TECHNOLOGY: SMARTSENSE uses the motor’s sensors at startup to provide cog-free starts, excellent torque and low speed drivability. Once the motor is turning, the ESC seamlessly transitions to Castle’s ultra-efficient sensorless mode with electronic timing to advance timing automatically for peak performance in all driving conditions. (Requires use of Castle brushless motor to utilize)  INTERNAL BEC (Battery Eliminator Circuit): COPPERHEAD 10 features a selectable 5.5V or 7.5V (6A peak) internal BEC to supply power to many of today’s high-torque servos, without requiring the use of an external BEC.  DUAL USE FAN GUARD: For crawler setups or others that do not require an ESC cooling fan, the fan is easily removed with four screws and the fan guard with the cool COPPERHEAD logo simply clicks back into place on the top of the ESC. It keeps the COPPERHEAD 10 looking mean and provides an extra measure of protection.  APPLICATION SPECIFIC MOTOR COMBOS: Available with a dozen different 4-POLE 12-SLOT sensored motor options to eliminate the guesswork in finding the right brushless power upgrade for your basher, crawler, on road vehicle, short course or monster truck (Motor not included). WARRANTY: The COPPERHEAD10 is proudly designed and manufactured in Olathe, Kansas USA and backed by the Castle Creations one-year warranty.  FULLY PROGRAMMABLE: Complete Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or wirelessly with the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (B-Link not included). TELEMETRY LINK CAPABLE: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX  Specifications: Recommended Motors: Castle 1406, 1410, 1412 and 1415 Series Sensored 4-Pole Brushless Motors Running Modes: SMARTSENSE™, Sensored Only and Brushed motor operation Input Voltage Range: 2s-4s (16.8V)  BEC Specifications: Selectable: 5.5V or 7.5V (6A peak) Operating Environment: Waterproof design, potted in durable injection molded case, allows or use in nearly any environment.  Data Logging: Yes, Data Log Lite with 5 data points. Sample frequency of 1 and 5 per second.  Connector Type: 4mm female bullets for motor connection   On/Off Switch: Yes Cooling Fan: 30mm removable fan included, operates from start up. Purchase also includes a dual use fan guard for use without fan.  Size: 2.19x1.39x1.33" (L x W x H with fan) Weight: 70.9 g / 2.50 oz. (with fan) Programmability: Fully programmable Castle feature set using Castle Link USB adapter (sold separately) and freely downloadable Castle Link Windows software. Needed to Complete: Battery Connector - Castle 4mm polarized connectors, XT60, Dean's Ultra Plug, or Traxxas Power Connector recommended. Product Use Statements: Although COPPERHEAD 10 is waterproof, it is not intended for operation while completely submerged in liquid. They can corrode when exposed to corrosive materials, such as salt water. Always rinse the ESC with clean water after exposure to corrosives or dirt.  Remove cooling fan prior to driving in wet conditions, it is not waterproof.  This product was added to our catalog on February 7, 2024

Read more less

CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor The Castle Creations Mamba XLX 2 1/5 Scale Sensored Brushless ESC/Motor Combo with 2028 800Kv motor is a product guaranteed to redefine the limits of large scale R/C. Though it shares the name of its predecessor, the Mamba XLX, this is an ESC that lives in a class of its own. Reengineered from the ground up, the Mamba XLX 2 is packed with a potent combination of design, hardware and software advancements that will set a new standard for large-scale power systems. Designed for 1/5 Scale models weighing up to 42 lbs, the XLX 2 is an incredible power upgrade for the Losi DBXL-E and Super Rock Rey, Arrma Kraton 8S and Outcast 8S, or Traxxas X-Maxx models! If you are looking for the ultimate upgrade for your speed run, drag racing or off road rigs - the XLX 2 is a true heavyweight, with no contenders. CRYO-DRIVE: MORE POWER – COOLER TEMPS – LONGER RUNS Castle’s latest break-through technology, minimizes the amount of time the ESC’s electrical components spend generating heat. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 50mm fan and a forged elliptical fin heatsink, the design maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling. NOTE: Some vehicles may require aftermarket parts to allow ESC and/or motor fitment.  Features: Sensored, Sensorless and SmartSense™ running modes Powerful Integrated 20A Peak Adjustable BEC (5.25V-8.0V) Premium forged heatsink with for superior airflow and increased heat dissipation Oversized factory equipped thermally controlled 50mm fan  Waterproof design for all weather conditions.  ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to  protect the components and promote efficient heat transfer Data-logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for “on the-fly” adjustments using your transmitter Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options.   Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming  with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store. Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1-year warranty Specifications: ESC: Input voltage range: 3S-8S LiPo Length: 3.98” (101.2mm) Width: 2.49” (63.3mm) Height: 2.2” (55.8mm) On/Off Switch: Yes, waterproof* Cooling Fan: Yes, thermally controlled factory equipped (50mm) fully removable** Weight: 13.1 oz (371g) Running Modes: Sensored, Brushed, Sensorless and SmartSense™ when paired with a Castle 4-POLE 12-SLOT Sensored Motor. (Dust cover included in package for non-sensored operation) Wire Gauge: 8AWG Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX, T7PXR Transmitters. Items Needed: Battery connectors designed for 150+ amps continuous, such as Castle 6.5mm polarized or CC BULLET 8.0MM Motor: Application Guidelines: 1:5th Scale vehicles weighing up to 30 lbs.  Vehicle Examples: Losi DB XL-E,™ Losi Super Rock Rey™, Arrma Kraton 8s™, Arrma Outcast 8s™, Traxxas X-Maxx™ (Some vehicles may require aftermarket parts to allow ESC and/or motor fitment) Input Voltage Range: MIN: 3S LiPo, MAX: 8S LiPo 33.6V Kv: 800Kv Max. RPM: 45,000 Diameter: 2.22” (56.3mm) Length: 4.44” (112.7mm) Shaft Size: 30mm (Length), 8mm (Diameter) Weight (w/wires): 44 oz./1.25kg Mounting Hole Specifications: Holes: 4mm, Spacing: 30mm Connectors: 8.0mm male connectors, 300mm Direct Connect Sensor Wire Includes: Mamba XLX2 ESC 2028-800kv Sensored Brushless Motor 300mm Direct Connect Sensor Wire Mamba Decals Mamba XLX2 Quick Start Guide Sensor port dust cover Coupon for free Castle Link USB This product was added to our catalog on October 12, 2021

Read more less

CSE060-0059-00, Castle Creations 1406 Sensored 4-Pole Brushless Motor (7700kV) Castle Creations 1406 Sensored 4-Pole Brushless Motors combine rotor position sensor technology with an improved high power and high efficiency motor design to deliver ultra smooth startup, precise low speed control, predictable power delivery, incredible torque, and lightning fast response. Through the use of Castle's Smart Sense technology, the position of the rotor is always known by the ESC. This eliminates the possibility of encountering cogging or inconsistency during startup, and allows the 1406 to deliver PRECISE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for. EFFICIENCY IS KEY The higher the efficiency of a motor the more power it can produce without overheating, which allows you to safely run higher gear ratios. The higher the efficiency of a motor, the less power it takes to produce the same output power, which allows you to run longer on a single charge. The higher the efficiency of the motor, the less energy it turns into heat; keeping it cool under extreme loads. Efficiency equals performance.RELIABILITY CAN’T BE IGNORED Without a robust and reliable design, efficiency will only go so far. The Castle engineers know this and spared no expense when developing a design that could hold up to the harsh conditions that the RC community will throw at it. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. High-strength, high-temperature grade neodymium sintered magnets combined with a high-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Proprietary winding techniques allow Castle to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. A cooler motor has a longer lifetime. Construction required careful component selection; each verified through internal testing to ensure the highest efficiency possible. In the end, the result is a motor with unmatched quality, performance, and reliability. INTEGRATED SOPHISTICATION Castle engineers always add a little something extra in their designs that takes your performance to the next level. When paired with a Castle Creations sensor supported ESC, like the MAMBA MICRO X, MAMBA MAX PRO or MAMBA MONSTER X, you can unlock advanced tuning capabilities that Castle Link provides specifically for sensored motors. With a Castle sensored ESC and sensored motor you will have the ULTIMATE POWER PLANT for your vehicle. SMARTSENSE™ SMARTSENSE uses the motors sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is turning, it seamlessly transitions to Castle’s ULTRA- EFFICIENT sensorless mode. When running, a motor must transition between different load points and a different timing advance is required for optimal efficiency at all load points. Using mechanical timing adjustments alone, you can only target one driving condition, such as higher start power or higher top end speed. This sacrifices performance and efficiency during the other driving phases. Electronic timing in SMARTSENSE will advance timing automatically for peak performance during all driving conditions. This allows users to combine the best of both worlds in an unrivaled HYBRID between smooth sensored startups and high-efficiency sensorless drive. Features: 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 13 AWG high strand wire with silicone insulation Kevlar wrapped rotor 6061-T6 Billet aluminum heatsink can High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: Input Voltage Range: 2 LiPo Kv: 7700 Max. RPM: 100,000 Length: 49.5mm Diameter: 36mm Weight (w/wires): 189 g / 6.7oz Shaft Size: 15mm Diameter: 1/8" (3.17mm) Mounting Hole Specifications: M3 @ 25mm Cooling Fan: Optional - Coming Soon Connectors: 4mm male Castle Bullet Connectors Application Guidelines: Ideal for 1/10th scale on-road cars for 2s use. Lighter off-road 1/10th stadium trucks and buggies with conservative gearing. NOT for use in 2WD or 4WD short course trucks. Recommended ESC(s): Mamba Max Pro, Mamba Monster X Max. Recommended Vehicle Weight: Up to 4lbs Tech Notes: Running modes: SMARTSENSE™, Sensored, Sensorless This product was added to our catalog on December 16, 2021

Read more less

CSE060-0081-00, Castle Creations 1717 Sensored 4-Pole Brushless Motor (1650Kv) The Castle Creations 1717, 1650KV Sensored 4-Pole Brushless Motor is a blast from the past with the added benefit of sensored capabilities! Featuring an improved 4-POLE 12-SLOT design, the sensored 1717 boasts exceptional efficiency and will generate less heat than comparable motors. This motor is a great option for any 1/6th scale model weighing up to 20 lbs and running up to 8s LiPo. The 1717 is also a great upgrade for drivers looking for an incredibly high torque 8s motor for 1/8th scale models as well! Without a robust and reliable design, efficiency will only go so far. Castle engineers know this and spared no expense when developing a design that could hold up to the harsh conditions that the RC community will throw at it, resulting in a cooler running motor. A cooler motor has a longer lifetime. Construction of this motor required careful component selection; each verified through internal testing to ensure the HIGHEST EFFICIENCY possible. In the end, the result is a motor with unmatched quality, performance, and reliability.Features: Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Proprietary winding techniques produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Updated modern and sleek design; looks as cool as it performs. IMPROVED 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT. QUIETSENSE™ technology shields the sensors from magnetic field noise generated from the motor coils and keeps your motor and ESC in sync at all times. Use of a Flux Shield™ in conjunction with secondary Sense Magnets delivers even HIGHER PRECISION and MORE EFFICIENT startups. OPTIMIZED design eliminates the need for mechanical timing adjustments. Sensor alignment method delivers uniform timing and torque in both directions, automatically. Specifications: Input Voltage Range: 8S LiPo Max Kv: 1650 Max. RPM: 56,000 Size: Diameter: 1.87” (47.6mm) Length: 3.35” (85.1mm) Weight (w/wires): 21.08 oz./597.6g Shaft Size: Length: 20mm Diameter: 5mm Mounting Hole Specifications: M3 and M4 @ 25.4mm (1") Cooling Fan: N/A Connectors: 6.5mm male bullets Recommended ESC(s): Mamba Monster X 8S Max. Recommended Vehicle Weight: Vehicles weighing less than 20lbs. Running modes: Sensorless and Sensored Product Use Statements: Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the the motor or ESC. Application Guidelines: The 1717-1650Kv is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the owners manual for running and maintaining motors in wet environments. This product was added to our catalog on March 22, 2021

Read more less

CSE060-0084-00, Castle Creations 1515 Sensored 4-Pole Brushless Motor (2200kV) The Castle Creations 1515 Sensored 4-Pole Brushless Motor is now offered in this eBuggy version. Taking the same crazy horsepower of the 1/8 1515-2200Kv motor this eBuggy version is now modified to work with the Mamba X 1/10 ESC in 1/8 buggy applications up to 9lbs. Using smaller 4mm bullet connectors and 12AWG wire this motor is ready to plug right into the Mamba X and overpower your next build!EFFICIENCY IS KEYThe higher the efficiency of a motor the more power it can produce without overheating, which allows you to safely run higher gear ratios. The higher the efficiency of a motor, the less power it takes to produce the same output power, which allows you to run longer on a single charge. The higher the efficiency of the motor, the less energy it turns into heat; keeping it cool under extreme loads. Efficiency equals performance.RELIABILITY CAN’T BE IGNOREDWithout a robust and reliable design, efficiency will only go so far. The Castle engineers know this and spared no expense when developing a design that could hold up to the harsh conditions that the RC community will throw at it. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. High-strength, high-temperature grade neodymium sintered magnets combined with a high-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Proprietary winding techniques allow Castle to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. A cooler motor has a longer lifetime. Construction required careful component selection; each verified through internal testing to ensure the highest efficiency possible. In the end, the result is a motor with unmatched quality, performance, and reliability.INTEGRATED SOPHISTICATIONCastle engineers always add a little something extra in their designs that takes your performance to the next level. When paired with a Castle Creations sensor supported ESC, like the Mamba X 1/10 ESC, you can unlock advanced tuning capabilities that Castle Link provides specifically for sensored motors. With a Castle sensored ESC and sensored motor you will have the ultimate power plant for your vehicle.Features:Improved 4-POLE 12-SLOT design boasts exceptional efficiency and produces less heat.QUIETSENSE technology shields the sensors from magnetic field noise generated from the motor coils and keeps your motor and ESC in sync at all times. Use of a Flux Shield in conjunction with secondary Sense Magnets delivers even higher precision and more efficient startups.Optimized design eliminates the need for mechanical timing adjustments. Our sensor alignment method delivers uniform timing and torque in both directions, automatically.Rebuildable design allows users to replace front end bell/bearing assembly or rotor/shaft assembly.ROAR standard sensor port and labeled connections.Updated modern and sleek design; looks as cool as it performs.Specifications:Input Voltage Range: 2S-6S LiPo (4s max when paired with Mamba X ESC)Kv: 2200Max. RPM: 60,000Length: 75.4mmDiameter: 40mm (41.4mm with fins)Shaft Length: 20mmShaft Diameter: 5mmMounting Hole Specifications: 3mm and 4mm @ 25mmCooling Fan: OptionalConnectors: 4mm male Castle Bullet Connectors, includes 210mm length sensor wire.Items Needed for Operation: Compatible Electronic Speed Control (ESC)Max. Recommended Vehicle Weight: Ideal for 1:8 scale Off-Road buggies weighing up to 9 lbs. Recommended ESC(s): Mamba X 1/10 ESCIncluded: (1) 1515 Sensored 4-Pole Brushless Motor (2200kV)(1) Sensor Cable (210mm)Mounting HardwareThis product was added to our catalog on April 12, 2024

Read more less

CSE060-0103-00, 4-Pole Sensored Brushless Motor, 2028-1700KV This product was added to our catalog on April 18, 2024

Read more less

HWA30108000, Hobbywing Quicrun 10BL60 Sensored Brushless ESC Features: High performance but low price- users can own this reliable race-ready ESC at an affordable cost. Compact size, suitable for various car chassis.  Auto identification system can recognize sensored or sensorless brushless motors automatically.  Smooth operation and plentiful adjustment options. Suitable for most kinds of competitions. 8 steps of timing adjustment greatly increase the output power of the motor and unlock its maximum potential.  Proportional brake with 4 steps of Maximum Brake Force adjustment, 8 steps of Drag Brake Force adjustment and 4 steps of Initial Brake Force adjustment.  9 steps of acceleration (punch) adjustment, from “soft” to “very aggressive” to fit various of cars, tires and tracks. Multiple protections: Low voltage cut-off protection for LiPo or NiMH battery / Over-heating protection / Throttle signal loss protection / Motor Lock-up protection.  One-button sets the ESC. Easily reset all parameters to factory default settings.  Compatible with optional device ---- the portable Digital LED Program Card, especially convenient for outdoor use. Specifications: Applications: 1/10 & 1/12 On-road / Off-road / F1 / Drift car race / Street race for fun / Club racing / STOCK race with 0 timing / Drift car race Cont./Peak Current/Resistance: 60A/380A/0.0008? Motor Type Supported: Sensored / Sensorless Brushless Motor Car Applicable: 1:10 On-road/Off-road/Buggy/Monster Motor Limit:  2S LiPo or 4-6 cell NiMH: ?8.5T(1/10 On-road), ?13.5T(1/10 Off-road)* 3S LiPo or 8-9 cell NiMH: ?13.5T(1/10 On-road), ?17.5T(1/10 Off-road)* Battery: 4-9 cell NiMH, 2-3S LiPo BEC Output: 6V/2A (Linear Mode) Size: 33mm(L)*28mm(W)*31.5mm(H, with cooling fan)  Weight: 59g (with wires, without cooling Fan) External Program Port: Available *NOTE: Indicates the limit value of motor turns when the ESC timing is set to 0. The larger the timing, the more turns the motor needs. This product was added to our catalog on May 3, 2023

Read more less

HWA30110000B04, QUICRUN WP 16BL30 COMBO (Bundled) - ESC + QR2435 motor G3 (4500kv) + Programmer ESC + QR 2435 SL 4500kv G3 motor + Programmer Waterproof, Sensorless system ESC Waterproof and dustproof for all-weather. One-button (the “SET” button on the ESC) sets the ESC. All parameters easily reset to factory default settings. Proportional brake with 4 steps of maximum brake force adjustment and 8 steps of drag brake force adjustment.  9 steps of acceleration (/punch) adjustment from “soft” to “Very aggressive” to fit different kinds of models, tires and tracks. Multiple protections: Low voltage cut-off protection / Over-heating protection / Throttle signal loss protection / Motor lock-up protection.  Motor  Cont./Peak Current: 65Ax4/80Ax4 Input Voltage: 2-3S Lipo/6-9 Cell NiMH BEC Output: 5V&0.6A Size: 55x42x6.6mm Weight: 15g This product was added to our catalog on May 3, 2023

Read more less

HWA30110000B05, QUICRUN WP 16BL30 COMBO (Bundled) - ESC + QR2435 motor G3 (6500kv) + Programmer ESC + Quicrun 2435 brushless motor 6500kv + LED program box Waterproof, Sensorless system ESC Waterproof and dustproof for all-weather. One-button (the “SET” button on the ESC) sets the ESC. All parameters easily reset to factory default settings. Proportional brake with 4 steps of maximum brake force adjustment and 8 steps of drag brake force adjustment.  9 steps of acceleration (/punch) adjustment from “soft” to “Very aggressive” to fit different kinds of models, tires and tracks. Multiple protections: Low voltage cut-off protection / Over-heating protection / Throttle signal loss protection / Motor lock-up protection.  Motor  Cont./Peak Current: 65Ax4/80Ax4 Input Voltage: 2-3S Lipo/6-9 Cell NiMH BEC Output: 5V&0.6A Size: 55x42x6.6mm Weight: 15g This product was added to our catalog on May 3, 2023

Read more less

HWA30408012, Hobbywing XERUN Justock 3650 SD G2.1 Sensored Brushless Motor (21.5T) The Hobbywing XERUN Justock 3650 SD G2.1 Sensored Brushless Motors feature an updated can design over the G2 - and especially G1 - and push the boundaries of an Fixed Timing Motor with lower weight, good heat dissipation and a rebuildable design. Features:  The use of a heat-resistant magnet attached aluminum case and double insulated windings, high precision bearings, and rotor with a strong structure guarantees outstanding performance and super durability. The built-in Hall sensor non-adjustable end bell combined with a high precision and balanced rotor guarantees the user a smooth and linear power on demand. The silicon O-ring seal fitted between the end bell and stator helps to conduct inner heat to the motor case and prevent dust from entering the HALL sensor. The detachable structure design for daily cleaning and maintenance can effectively prolong the service life of this Justock motor and improve its operating efficiency. This motor is perfectly matched with the XR10-Justock ESC for all zero timing spec racing and also compatible with other Hobbywing Electronic Speed Controllers including other brands. This Justock motor is applicable to various 1/10th, 1/12th on-road & off-road vehicles. It can be an ideal choice for Stock or Sport class races but can also be a nice choice for newbies for practice. The motor design is in compliance with IFMAR, and ROAR specifications. Specifications:Scale: 1/10, 1/12Brushless: YesSensored: YesPole Count: 2KV Rating: 2050LiPo Cells: 2-3SNo-Load Current(A): 3Outer Diameter: 35.9mm (1.413")Length: 52.5mm (2.067")Shaft Diameter: 3.17mm (0.125")Weight: 175g (6.17oz)Timing: FixedApplications: STOCK/SPORT class (choose the motor as per competition rules) of 1/10th , 1/12th On-road (i.e. competition touring car or drift, F1, Mini car, and etc.) and Off-road (i.e. buggy, 2WD SCT & truck) racing, Normal Training, and Rock Crawlers (21.5T & 25.5T only). This product was added to our catalog on May 3, 2023

Read more less

HWA30408013, Hobbywing XERUN Justock 3650 SD G2.1 Sensored Brushless Motor (25.5T)

Read more less

HWA38020322, Hobbywing XR10 Justock G3 Sensored Brushless ESC/SD G2.1 Motor Combo (21.5T) The Hobbywing XR10 Justock G3 Sensored Brushless ESC/SD G2.1 Motor Combo has been designed with fixed, 0°, timing for spec class racing. The included SD G2.1 motor is an ideal stock motor for both 1/10 and 1/12 on and off-road racing. These two components paired together make for an ideal choice for beginners and experts alike.Features: ESC: Built-in polarity protection. The XR10 Justock has integrated MOSFET's that if the battery terminals are connected in reverse, the MOSFET will be reverse-biased and will not allow current to flow through the system Programmable via OTA Bluetooth module or 3in1 program box Built-in capacitor module eliminates the need for external capacitors and unwanted space RPM speed limit function supports up to 6 different speed, RPM, selections to meet the needs and demands of various competitions in the world (Set through OTA module or 3in1 box) Internal ESC timing has been set to 0 degrees and cannot be adjusted for stock racing Built-in BEC can support a maximum output current of up to 8A. Output voltage can be set between 6V or 7.4V Calibration or preforming a factory-reset can be achieved by using this SET button. Simple and easy to use Supports both CCW (counterclockwise) and CW (clockwise) motor directions Protection functions include: reverse polarity, battery voltage, ESC temperature, motor temperature, signal lost and locked rotor protection Supports ESC firmware upgrades User-friendly and convenient for set-up Motor: Use of a heat-resistant magnet attached aluminum case and double insulated windings, high precision bearings, and rotor with a strong structure guarantees outstanding performance and super durability Built-in Hall sensor non-adjustable end bell combined with a high precision and balanced rotor guarantees the user a smooth and linear power on demand Silicon O-ring seal fitted between the end bell and stator helps to conduct inner heat to the motor case and prevent dust from entering the HALL sensor Detachable structure design for daily cleaning and maintenance can effectively prolong the service life of this Justock motor and improve its operating efficiency This Justock motor is applicable to various 1/10th, 1/12th on-road & off-road vehicles. It can be an ideal choice for Stock or Sport class races but can also be a nice choice for newbies for practice The motor design is in compliance with IFMAR, and ROAR specifications Specifications: ESC: Continuous Current: 60A Burst Current: 380A Battery: 2S Lipo (Only 2S) Built-in BEC: 6V/7.4V @ 4A(Switch-mode) ESC programming: Independent programming port Motor Supported: Sensor and sensorless brushless motor Motor Limit: 10.5T, or greater, 3650 Motor Application: 1/10, 1/12 On-road and Off-road Cooling Fan: Powered by BEC Size: 40.9x33.9x32.1mm (LxWxH) Weight: 75.4g (Including weight of wire) Motor: Scale: 1/10, 1/12 Brushless: Yes Sensored: Yes Pole Count: 2 KV Rating: 2050 LiPo Cells: 2-3S No-Load Current(A): 3 Outer Diameter: 35.9mm (1.413") Length: 52.5mm (2.067") Shaft Diameter: 3.17mm (0.125") Weight: 175g (6.17oz) Timing: Fixed Includes: (1) Justock G3 ESC (1) Justock 21.5t G2.1 brushless motor (1) 5V cooling fan (1) Sensor cable This product was added to our catalog on May 3, 2023

Read more less

HWA38020334, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (13.5T) This is the Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo. Using the precise control of the XR10 Pro G2S combined with a powerful V10 G4 motor gives the user a dominant combo! XR10 Pro G2S 160A ESC: The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC offers all the tuning options needed for competitive racing while giving reliable performance on the track. Helping to keep this ESC reliable is the Frameless Fan Design (FFD) fan system. A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. At the racetrack ESC adjustments can be crucial. The XR10 Pro G2S is packed with features such as several PWM adjustments. From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition.V10 G4 Motor: The V10 G4 Competition Stock Brushless Motor has been greatly optimized to provide maximum torque and increased power. With a lower internal resistance, this motor is more efficient and runs cooler when compared to the G3R motors. To further increase performance the motor adopts a fully exposed stator core allowing more airflow over the stator. The motor also features a high-precision endbell plate to improve consistency and structural stability. Dual sensor ports can be found allowing for different wiring setups.NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended. Features: ESC: Upgraded 32-bit M4 microprocessor with more powerful processing capability guarantees stable control and rapid response. (Industry's highest 32-bit microprocessor, increased processing speed by X4) Peak current up to 1200A. (This is not a typo) Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages. Variable frequency regulation of PWM & amp; brake frequencies allows users to precisely regulate the driving; braking forces (of the motors). Expanded range of the max. brake force brings in the active brake ranges from 101% to 150%. Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency. 10 select-to-use profiles applicable to all 1/10th RC car racing. Internal electronic key switch for long service life, high reliability; and the external switch port for connecting an external switch (included in the product box) is applicable to different situations. Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or WiFi module to the ESC. With the Updated WIFI express module (purchase separately), users are able to program parameters, upgrade firmware and check relevant data during the event using either the iPhone or Android devices. Switchable motor direction (CCW/CW) for various chassis. Multiple protections comes in standard Low-voltage cutoff protection ESC and motor thermal protection Fail safe (throttle signal loss protection) Reverse polarity protection Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real time. Firmware upgrade via Hobbywing multi-function LCD program box or WiFi Express (item sold separately). Motor: Specially designed for high-level racing.  Lightweight: The G4 Modified & Stock motors only weigh 161g & 132g respectively. The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor. The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G4 Stock motors (10.5T~25.5T), the timing is adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees. The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts. The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors effectively keep sand or dirt from getting inside and damaging the motor(s). The use of high-performance stator core, heat (200°C) resistant wire, heat (200°C) resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current endurance guarantees outstanding performance and super durability. Specifications: ESC: Cont./Peak Current: 160A / Burst: 1200A  Battery: 5-6 cells NiMH/NiCd / 2S LiPo  BEC Output: 5V-7.4V Motor Supported: Sensored and sensorless brushless motors  Suitable Motor: 3650 Motors 1/10th Touring Car: 4.5T, 1/10th Buggy: 5.5T Application: Brushless motor system for 1/10th, 1/12th Touring Cars & Buggies Racing, Splash proof Wires: Standard 13AWG 200mm Size: 37.5X30.9X32.5mm  Weight: 90g (with wires) Motor:  kV Rating: 3950kV Cell Count: 2-3S No-Load Current: 4.5A Outer Diameter: 35.8mm Length: 51.4mm Shaft Diameter: 3.175 Weight: 149g Front Bearing: 9x4x4mm Rear Bearing: 8x3x4mm Adjustable Timing: 30-60° Applications: 1/10th Stock Class Racing This product was added to our catalog on July 20, 2022

Read more less