HobbyWing has come out with an ESC durable enough to handle even the most high-performance RC Wings. Never worry about your ESC again, with a burst rating of up to 80A!  Make sure to check out the rest of our wing products and our entire line of HobbyWing gear! Features Safety arming feature: Regardless the throttle stick position, the motor will not spin after battery connected Throttle calibration function: Throttle range can be calibrated to be compatible with different transmitters Multiple program methods supported: transmitter stick, LED Program Card. Very easy to program the ESC at home or at the flying field Full protection: Low voltage cutoff protection / Over-heat protection / Throttle signal loss protection Specifications Input Voltage: 3-7S Max Continuous Current: 60A Max Burst Current: 80A Refresh Rate: 50Hz to 432Hz BEC: 5V@7A Dimensions: 73x30x12mm Weight: 68g Includes 1x HobbyWing Skywalker V2 3-7 Wing 60A ESC

Read more less

Take a look at the XRotor F7 Convertible Flight Controller from Hobbywing. This FC is similar to other versions with its OSD, and voltage monitoring, but the F7 now comes with an all-new 5V & 12V dual BEC Circuit and a special interface for the DJI image transmission system. The XRotor F7 Convertible flight controller is equipped with STM32F722 MCU which has a powerful computing ability and fast running speed. High sensitivity ICM20602 six-axis motion sensor, built-in 5V & 12V double BEC, integrated OSD, and a pitch module.   Check out our other flight controllers, and our Hobbywing selection! Features Equipped with STM32F722 MCU which has powerful computing ability and fast running speed, and high sensitivity MPU6500 six-axis motion sensor. Supports BetaFlight, Cleanflight, Butterflight, Inva, and other mainstream FPV firmware. DJI image transmission system port equipped with corresponding flat cable Supports bidirectional DShot digital throttle communication. Unique installation design and shock absorption structure. On-board large capacity Flash memory chip. On-board 5V & 12V dual BEC circuit. On-board Pit Switch module. Specifications Firmware: HOBBYWING_XROTORF7CONV FC Programming: Supported Programming via Betaflight/ Cleanflight-configurator Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, PROSHOT1000 Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL OSD Built-in Input Voltage: 3-6S Gyro: MPU6500 Voltage Monitoring Supported Current Monitoring Supported External Buzzer Supported LED Control Supported BEC 5V @ 1.5A ; 10V @ 1.5A Mounting Pattern: 20x20mm M3 / 30x30mm M3 Size 32x32mm Weight 3.3g  Manual Download Includes 1x Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller 1x Soft Mounting Grommets Set 1x Signal Cable 1x User Manual

Read more less

Equipped with a powerful STM32F722 MCU and sensitive MPU6500 6-axis motion sensor, the XRotor F722 Stack/Combo offers bidirectional DShot digital throttle communication and a large on-board Flash memory. It also supports various FPV firmwares with adjustable parameters. Its 30/20mm double hole distance and flexible flat cable module (ideal for Hobbywing tower 4in1 ESC) with shock absorption mechanism reduce external vibration impact. For convenience, it includes a PIT switch module, dual BECs (5V & 10V), DJI image transmission port, Amp/Volt monitoring port, buzzer output port, and Micro USB port.  Check out all our 20x20 stacks, and our Hobbywing selection! Features Manual for the FC Manual for the ESC Super hardware and running speed  Special interface for DJI image transmission system On-board 5V & 10V dual BEC circuit On-board Pit Switch module Perfectly support firmware of various FPV Unique installation design and shock absorption structure Perfectly match with Hobbywing ESC Volt/Amp monitoring port Buzzer output Micro USB Switch module of board load graphic transmission(VTX) Specifications XRotor F7 FC MCU: STM32F722 Gyro: MPU6500 Barometer: No OSD: Yes Blackbox: Onboard UARTS: 4 Sets ESC Software: DShot300/600/12000 ESC Telemetry: Yes Led Controller: Yes Input Voltage: 3-6s Lipo (12.6-25.2V) BEC: 5V 2A / 10V 2A Mounting Pattern: 20x20mm M3 / 30x30mm M3 XRotor 45A BLHeli_32 ESC Input Voltage: 3-6S Max Continuous Current: 45A  Max Burst Current: 60A  BEC Output: NO Firmware: Hobbywing_XRotor_BLHeli-32 Version Throttle Calibration: Supported ESC Programming: Stick Programming, BLHeliSuite32 DEO: Supported OneShot Mode: Supported Timing: Supported Motor Rotation: Supported Mounting Pattern: 20x20mm Weight: 12g Includes 1x Hobbywing XRotor F722 3-6S 20x20 Stack/Combo (F7 FC / 32Bit 45A 4in1 ESC) 1x Hardware Set 1x AMASS XT60 Connector 1x Cable Set

Read more less

The Hobbywing XRotor F722 Stack/Combo packs in the latest tech: 65A (x4) ESCs, BLHeli_32 DShot 1200 support, two 5V BECs, plus a voltmeter module that lets your FC know your battery's voltage and amperage in real-time! The F7 Flight Controller offers OSD, voltage monitoring, two BECs, and an interface for the DJI image transmission system. Build the perfect multirotor with this feature-packed, powerful combo!  Check out all our 30x30 stacks & combos, and our Hobbywing selection! Features Manual for the FC Manual for the ESC XRotor 65A 4in1 ESC High performance 32-bit microprocessor with the running frequency of up to 120MHz for excellent performance. Third generation BLHeli_32 code can support up to 128KHz PWM output frequency, which can be compatible with more motors. All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling. Code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments. The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us) and Multishot (5-25us). Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power up. Also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttle. This can be very useful for finding lost aircraft. F7 Flight Controller Features STM32 F722 MCU allows the FC to run the PID looptime and gyro with higher frequency. Onboard OSD microchip which supports the DMA mode allows users to adjust its parameters via the Betaflight software. (Note: the OSD is controlled by the F4 MCU.) The FC supports Betaflight firmware and allows parameter adjustment via Betaflight software is more applicable to FPV racing. Onboard Flash chip can record and save flight/black box data allowing users to adjust the setup of their aircraft easily. Compatible with various receivers like SBUS, SUMH, SUMD, SPEKTRUM1024/2048, XBUS and etc. LED strip signal output port allows users to adjust the color and flash mode of the LED strip via the FC. Volt/Amp monitoring port allows users to check the battery voltage (BAT port) and current (CRT port, extra current meter is needed). Buzzer output port allows users to connect external buzzer(s) to the FC for warning or informing the flight status of the aircraft. Micro USB port allows users to connect the FC to a PC to flash firmware and adjust parameters. Board load 5V and 10V BEC, both can output 2A. It can supply power for receiver, VTX, LED lamp and others devices.  Specifications XRotor F7 FC Compatible with (Multirotors) Quadcopters Firmware HOBBYWING_XROTORF7CONV FC Programming Supported Programming via Betaflight/ Cleanflight-configurator Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, PROSHOT1000 Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL OSD Built-in Voltage Monitoring Supported Current Monitoring Supported External Buzzer Supported LED Control Supported BEC 5V @ 1.5A ; 10V @ 1.5A Size 32x32mm Weight 3.3g XRotor 65A BLHeli_32 ESC LiPo Power input: 3-6S Cont.Current: 65Ax4 Burst Current: 80Ax4 BEC Output: 5V@ 0.5A Input wires: 12AWG-130mm* (Red/Black) Output Wire: No wires but solder tabs Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no Weight / Size: 15.0g / 32.7x18.4x6.2mm Mounting holes: 30.5x30.5mm Throttle Calibration: Supported ESC Programming: BLHeliSuite32 Includes 1x Hobbywing XRotor F722 3-6S 30x30 Stack/Combo (F7 FC / 32Bit 65A 4in1 ESC) 1x Hardware Set 1x AMASS XT60 Connector 1x Cable Set

Read more less

If you never want to worry about your your 4-in-1 again, Hobbywing's XRotor 65A raises the bar once again! From Captain Vanover himself, this thing is "bullet proof". No matter what type of flight style you choose, this should be a go-to 4-in-1 for everyone! The soft mounts prevent most of the vibration from being transferred to the FC. From freestyle to racing, even long range will not challenge this ESC. The 65A Micro 4-in-1 ESC comes loaded with the latest 32bit tech (the third generation BLHeli_32 code can support up to 128KHz PWM output frequency), DShot1200, Larger FETs, direct pins for a capacitor, and a choice of either a plug n play ESC connector or solder pads for the flight controller. Check out all our 4in1 ESCs, all our 30x30 ECSs, and all our Hobbywing products! Features High-performance 32-bit microprocessor with a running frequency of up to 120MHz for excellent performance. The third generation BLHeli_32 code can support up to 128KHz PWM output frequency, which can be compatible with more motors. All codes use damped light mode. Damped light does regenerative braking, causing very fast motor retardation, and inherently also does active freewheeling. The code supports features to prevent sync loss. There are tunable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments. The code supports regular 1-2ms pulse width input, as well as Oneshot125 (125-250us), Oneshot42 (41.7-83.3us), and Multishot (5-25us). Dshot signaling is supported at any rate up to at least Dshot1200. The input signal is automatically detected by the ESC upon power-up. The code also supports a beacon functionality, where the ESC will start beeping after a given time of zero throttles. This can be very useful for finding lost crafts. Specifications LiPo Power input: 3S-6S Cont.Current: 65Ax4 Burst Current: 80Ax4 BEC Output: 5V@ 0.6A Input wires: 12AWG-130mm (Red/Black) Output Wire: No wires but solder tabs Connectors: (In/Out) XT60 (w/ Wires Soldered on) /no Weight: 15.0g  Size: 52x42x6.6mm Mounting holes: 30.5x30.5mm Throttle Calibration: Supported ESC Programming: BLHeliSuite32 Includes 1x Hobbywing XRotor Micro 32bit 65A 4-6S 30x30 4in1 ESC w/ BEC

Read more less