GEPRC ELRS NanoSE receiver is a new generation remote control system developed based on the ExpressLRS open source project. ExpressLRS sets new standards for long-range connection, low latency, and a maximum refresh rate of 500Hz. GEPRC ELRS NanoSE receiver operates at a frequency of 2.4 GHz. Compared with the Nano receiver, the NanoSE receiver uses an Integrated SMD ceramic antenna, which further reduces its size while ensuring signal reception, making it more suitable for use on drones with limited space and lightweight. Note: ELRS products now shipping have been pre-flashed with 2.x firmware. 2.x is not compatible with version 1.x, so you need to upgrade the transmitter to 2.x for proper frequency matching. Check out the rest of our RC receivers and all our RC transmitters, modules, and accessories! Features Small size 0.4g weight WIFI Upgrade firmware ELRS open source project, remote control Integrated SMD Ceramic Antenna Maximum refresh rate of 500Hz The operation is simple Specifications Small size 0.4g weight WIFI Upgrade firmware ELRS open source project, remote control Integrated SMD Ceramic Antenna Maximum refresh rate of 500Hz The operation is simple Includes 1x NanoSE receiver 2x Heat shrink tube 4x Silicone cable（black, red, yellow, green） 1x Pin (4pin) 1x Instruction manual 1x Sticker

Read more less

Taking your drone photography to the next level, the new series Cinebot30, take you to the real world, shooting extreme footage. Cinebot30 is a new generation of Cinematic FPV drone developed by GEPRC team. The high-strength 7075 aircraft-grade aluminum alloy bracket for FPV camera escort, the combination of classic engineering and aesthetics. The newly polished gimbal damping module can easily fix high-frequency vibration and jello issues. It can be mounted with GEPRC Naked GoPro Hero 8 and GoPro Black Bones, Insta 360 GO2 and other cameras. The image is stable and clear, and it’s easy to film. Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again! Cinebot30 will be equipped with a powerful 1804 motor with optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmx3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations. Finely polished frame design, only 6 screws need to be removed to separate the aircraft top plate and protection frame. Easy to cope with the urgent need to replace the accessories, at any time to restore the state. Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Design that combines engineering and aesthetics. Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts. Selected high-toughness and impact-resistant PC material for injection molding. Aviation 7075 aluminum alloy camera mounting bracket and fuselage aluminum column. Propeller guard embedded ring Cob light strip, carefully tuned light effect. Color brightness in the day and night can be clearly displayed. The newly developed gimbal shock absorption structure can disintegrate high frequency jitter and jello effect. Easily carry a variety of action cameras. Powerful 1804 motor, surging torque to deal with ultra-low altitude flight at will. With the new GEP-F722-45A AIO V2, stable performance, more secure flight Four kinds of FPV system with the program, choose to belong to your first-person view Tuned by GEPRC professionals, delicate and silky flying feel Specifications Input Voltage: 3-4S Wheelbase:127mm Isolation Plate:2mm Main plate:3mm Bottom plate:1.5mm Motors: SPEEDX2 1804-3450KV Propellor: HQ prop T76mmx3 propeller VTX: GEPRC RAD 1W Antenna: Peano 5.8G 110mm RHCP MMCX Antenna Camera: Caddx ratel 2 Weight: 206.4g GEPRC GEP-F722-45A AIO Model: Cinebot30 HD Nebula PRO Quadcopter Gyro: BMI270/42688 gyro/accelerometer(SPI) OSD: Yes ESC Connections: Yes Firmware: GEP-F722-45A AIO BEC: 5V 1A Current Sensor: Yes Buzzer: no Barometer: No Input Voltage: 2-4S LiPo MCU: STM32F722RET6 IMU: ICM-42688-P Stack Size: 25x25mm Dimensions: 32x32xmm Weight: 8.8g Includes 1x GEPRC BNF CineBot30 4S 3" Analog Cinewhoop - Choose Version 2  x  HQProp T76MM（pair） 1  x  Battery strap M15x200mm 1  x  Battery strap M15x220mm 2  x  Battery Silicone Pads 1  x  Set of screws 1  x  Set of screwdrivers 1  x  GoPro camera mount holder 1  x  Set of screws 1  x  Set of screwdrivers 1  x  Antenna fixed tube

Read more less

Since DJI released the O3 AIR Unit FPV high-definition video transmission system, the GEPRC team has followed closely to make the latest set of the O3 AIR Unit system, the Cinebot30 HD O3 AIR Unit version. The Cinebot 30 is a new generation of cinematic FPV drones developed by the GEPRC team. The aluminum parts of the camera are still made of high-strength 7075 aircraft-grade aluminum alloy materials. The TPU shock-absorbing pad is designed on the bracket structure, which can excellently isolate the high-frequency vibration of the fuselage so that the camera can still obtain jelly-free high-definition images during high-speed flight The installation of the video transmission has also designed an assembly scheme, which allows the O3 video transmission to be completely installed inside the fuselage without affecting the Type-C USB data cable connected to the Air Unit to read video data. O3 Air Unit is currently the most advanced FPV system on the market. It can transmit 1080P 60fps real-time images, and can also record up to 4K 60fps images with an anti-shake effect at the same time.The upgraded video transmission system also combines market feedback to upgrade the gimbal top plate of the fuselage, which is compatible with the camera base fixed by 4-hole screws, so that Cinebot30 can mount a full-sized GoPro camera very well, and the battery life can reach 5 minutes and 30 seconds. However, the GEPRC team recommends flying with Naked GoPro 10, with a battery life of up to 10 minutes and 30 seconds.Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!Cinebot30 will be equipped with a powerful 1804 motor with an optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmX3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations.Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots! Features Adopts the most advanced O3 Air Unit FPV digital video transmission system on the market Video transmission with high-definition anti-shake 4K 60fps ultra-high resolution video quality The highest bit rate is 50MBPS, the delay is as low as 30 milliseconds, and the highest image quality is 1080P 60FPS Upgraded the top plate of the fuselage gimbal, compatible with the camera base fixed by 4-hole screws, and supports mounting a full-sized GoPro camera for flight The camera aluminum mechanism is designed with TPU shock absorption, which can effectively eliminate the image jello caused by the vibration of the body The ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. Color brightness can be clearly displayed in day and night Selection of high-quality high-toughness, impact-resistant PC&PET material injection molding Powerful 1804 motor, surging torque to cope with ultra-low altitude flight Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts With the new GEP-F722-45A AIO V2, the performance is stable and the flight is more secure Tuned by GEPRC professionals, delicate and silky flying feel Specifications Model: Cinebot30 HD O3 Quadcopter Brand: GEPRC Frame:  GEP-CT30 O3 Wheelbase:127mm Isolation Plate:2mm Main plate:3mm Bottom plate:1.5mm FC: GEP-F722-45A AIO V2 MCU: STM32F722RET6 IMU: ICM-42688-P VTX:  DJI O3 Air Unit Video resolution: 4K@50/60fps, 2.7K@50/60/100/120fps, 1080p@50/60/100/120fps Camera:  DJI O3 Propeller: HQ prop T76mmx3 propeller Antenna: DJI O3 Antenna Charge connector: XT60H-M Motor: SPEEDX2 1804-2450KV（6S Version）/ SPEEDX2 1804-3450KV（4S Version） Weight: Nebula Pro version 222.5g / Avatar version 221g / Analog version 209.2g / Link Wasp version 222.5g / O3 version 234.7g (excluding battery, the above are TBS Nano RX version) Receiver: PNP, Frsky R-XSR, TBS Nano RX, ELRS 2.4G Recommended Battery: LiPo 4S 1100mAh-1300mAh (4S Version) / LiPo 6S 850mAh-1100mAh(6S Version) Includes 1x Cinebot30 HD O3 Quadcopter 2x HQProp T76MM（pair） 1x Battery strap M15x200mm 1x Battery strap M15x220mm 2x Battery Silicone Pads 1x Set of screws 1x Set of screwdrivers 1x GoPro camera mount holder 1x Set of screws 1x Set of screwdrivers 1x Antenna fixed tube

Read more less

For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: GEPRC 5.8GHz@600mW Camera: Caddx Ratel2 Antenna: GEPRC Peano 5.8G RHCP MMCX Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 Analog 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut

Read more less

Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5" Cinewhoop. This powerful model features an analog & micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch. Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features New appearance design, strengthening carbon plate, hollow design, injection protection frame, noise reduction design, flight safety, silent. Adopts the GEP F722-45A AIO V2 high performance flight controller. SPEEDX2 2105.5 motor with HQ DT90 propeller, stable power output, and smooth flight feel. Power cable using XT60E1-M plug and carbon plate integrated design, convenient application. Battery installation method using a tie with 7075 aluminum parts fixed, solid and stable. Carefully tuned 3.5-inch cinematic FPV quad with flexible and delicate flight feeling. Pre-Installed with a M8U GPS   Specifications Model: Cinelog35 V2 Analog Frame: GEP-CL35 V2 Wheelbase: 142mm Gimbal Plate: 2.0mm Top Plate: 3.5mm Bottom Plate: 1.5mm FC system: GEP-F722-45A AIO V2 MCU: STM32F722RET6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 45A VTX: GEPRC RAD 1W(UFL) Camera: Caddx Ratel2 Antenna: GEPRC Peano 5.8 RHCP UFL Motor: SPEEDX2 2105.5-2150KV (6S) Propeller: HQProp D-T90MM GPS: GEP-M8U Receiver: ELRS2.4G Weight: 262g Recommended battery: LiPo 1050mah-1300mah Flight time: 5′00″ - 8′ 30″ Includes 1x GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS) 2x HQProp D-T90MM（2 pairs） 2x M20 x 250mm battery strap 2x Battery Silicone Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x L-shaped screwdriver (2mm) 1x L-shaped screwdriver (3mm) 1x M5 wrench 1x plastic tweezers 1x Antenna fixed tube (pair) 1x Keychain 1x GP Camera Mounting Base 1x Naked GP Camera Mounting Base 1x Antenna Mounting Base

Read more less

The GEPRC team has an amazing history of pushing boundaries and redefining standards in long-range FPV. Introducing the Crocodile75 V3: designed for comfort and stability, with a novel appearance, O3 Air Unit and special cooling components for efficient cooling, SPAN G50A BLHeli_32 4IN1 ESC, and 2806.5 1350KV motor and expertly tuned performance. Experience the passionate flight of the Crocodile75 V3! The battery plug is integrated with the fuselage for convenient application.  The overall performance of Crocodile75 V3 has been carefully and strictly tuned by the GEPRC team to bring the most passionate flying experience for pilots. Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Adopt a novel appearance design, strengthen the fuselage structure, and reduce the impact of fuselage vibration on the gyroscope sampling data. Equipped with SPEEDX2 2806.5 1350KV motor and HQ7.5×3.7×3 with sufficient power and high efficiency. Upgrade the ESC to SPAN G50A BLHeli_32 4IN1. Add protective side panels to effectively protect the electronic control system from instability caused by sand and dust pollution The integrated design of the battery plug and the body simplifies the power-on operation, simplicity and beauty. Equipped with O3 Air Unit and added special heatsink, excellent heat dissipation, to avoid O3 Air Unit overheating and stop recording. The Crocodile75 V3 has a lengthier fuselage, can be mounted with Lipo 6S 3300mah-4500mah or Lion 6S 6000mah battery for flight. Perfect match for 7-inch or 7.5-inch propellers Specifications Specifications Model: Crocodile75 V3 HD O3 Frame: GEP-LC75 V3 Wheelbase: 342mm Top plate: 2.5mm Bottom plate: 3.0mm Arm plate: 6.0mm Splint plate: 2.5mm FC: SPAN F722-BT-HD V2 ESC: SPAN G50A BLHeli_32 4IN1 MCU: STM32F722RET6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip VTX: O3 Air Unit Camera: O3 GPS: GEP-M8U Antenna: Momoda 5.8G LHCP RP-SMA x2 Motor: SPEEDX2 2806.5 1350KV Propeller: HQProp7.5x3.7x3 Weight: 628.5g Receiver: GEPRC ELRS 2.4G Recommended battery: Lipo 6S 2600mah-4200mah / Lion 6S 6000mah Flight time: 12-30 min Includes 1x GEPRC BNF Crocodile75 V3 HD LR 6S 7" Long Range Quad w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz (GPS) 4x HQProp7.5x3.7x3 2x M20x250mm battery straps 2x Battery Silicone Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x L-shaped screwdriver (2mm) 1x L-shaped screwdriver (3mm) 1x M5 wrench 1x GEPRC Keychain 1x GP Camera Base

Read more less

Does not come with naked Gopro mount. Please refer to the includes list at the bottom of the listing for all included items.  The classic CL25 Frame, designed by the GEPRC team, has been upgraded. They've redesigned the shock absorption structure of the camera mount, eliminated the jelly coming from the FPV camera, and you can now use 3, 4, and 5 damping rings according to the flight state to obtain the best stability in vibration and noise. The CL25 can be used for Vista HD digital image transmission system or Analog image transmission system. The center of gravity of the quadcopter is in the middle,  Check out all our DJI-compatible frames, electronics, and accessories as well as our whole GEPRC product line! Specifications Dimensions: 109mm Frame Style: Cinewhoop Top Plate: 2.5mm Bottom Plate: 1.5mm Bottom Plate(camera): 2mm Stack Size: 26.5x26.5mm Motor Mount: 9x9mm (compatible with 1105/1204/1206 motors) Camera Mount: 14-20mm (Nano and Micro-sized) Weight: 47.8g Recommended: Motor: BetaFPV 1404 4500Kv Micro Motor 4 Pack FC/ESC: GEPRC F411 2-6S AIO Flight Controller w/ 35A 4in1 ESC Prop: Gemfan D63 Ducted Durable Tri-Blade 2.5" Cinewhoop Prop 8 Pack LiPo: RDQ Series 14.8V 4S 650mAh 80C LiPo Micro Battery Includes 1x Top plate 2.5mm 1x Bottom plate 1.5mm 1x Bottom Plate (Camera)1.5mm 4x (M2x3.5x25mm) Aluminum posts 2x (M2x3.5x8mm) Aluminum posts 28x (M2x6mm) YFS Round head screws 2x (M2x8mm) YFS Round head screws 4x (M2x12mm) YFS countersunk head screws 16x (M2x2mm) Nylon Nuts 4x (M2x18mm) YFS countersunk head screws 5x Damping Rings 1x (19x19mm) Mount of camera 1x (14x14mm) Mount of camera 1x 3D print part of XM antenna 1x 3D print part of TBS antenna 1x Naked Camera Mount (This is just the base, NOT the actual camera case) 2x Batteries pads 2x EVA Landing pads 4x 2.5-inch Guards 1x EVA Damping Ring of Guard 2x Antenna Tubes 2x Batteries straps (M15x150mm）

Read more less

The CineLog35 Frame developed by CEPRC for mounting GoPro cameras is now officially released. CL35 is an improvement on the CL30 Cinelog30 frame. It supports the installation of mainstream AIO FC with 26.5mm x 26.5mm holes. The VTX installation hole is 20mm x 20mm, which can be directly installed with Vista HD image transmission. The propeller guard adopts an integrated design, and the overall structure is firmer. GEP also upgraded the power system and chose a 12mm x 12mm motor hole position. When compared to CL30, the CL35 can install a larger 15-18-20 series motor, with a 3.5-inch propeller, and it has stronger power output. They've improved the damping rings, the shooting effect is more stable and clearer and you can use 3D prints to install the GoPro 8, GoPro 9, and GoPro 10. Or use the base to install a naked GoPro 8, Insta360 GO2, or Caddx Peanut camera. We pursue lighter body weight, better flying feel, and more extended functions. Check out all our DJI-compatible frames, electronics, and accessories as well as our whole GEPRC product line! Specifications Dimensions: 203x203x42mm (Including the propeller guard) Frame Style: Cinewhoop Top plate: 2.5mm Bottom plate: 2.0mm Arm Plate: 3.5mm Stack Size: 26.5mm x 26.5mm Motor Mount: 12x12mm Camera Mount: 14-19mm (Nano and Micro) Weight: 130.7g (with Prop guards, and 3D printed parts included) Recommended:  Motor: EMAX ECO II 2004 2000Kv Motor FC/ESC: GEPRC F722 2-6S F7 AIO 2 45A 8-bit ESC Prop: HQ Prop T90MMX3 Tri-Blade 3.5" Cinewhoop Prop 4 Pack LiPo: RDQ Series 22.2V 6S 1300mAh 100C LiPo Battery Includes 1x Top Plate 2.5mm 1x Arm Plate 3.5mm 1x Bottom Plate 2.0mm 2x Propeller guards 1x Power cable combination 1x  Screw combination 1x  Screwdriver combination 1x  3D Print mountings combination 1x Other Parts

Read more less

Replacement part for the GEPRC Crocodile Frame. Check out our selection of micro frames and all our GEPRC products! Includes 1x GEPRC Crocodile Baby Top Plate

Read more less

The ELRS DUAL 2.4G Diversity Receiver from GEPRC is a game-changing, dual-antenna system utilizing ExpressLRS open source tech. It offers exceptional coverage, low latency, and a fast refresh rate of 1000Hz, all at a budget-friendly price! With its optimal positioning of dual antennas, it offers far better signal reception and sturdier connection than most single-antenna setups. It uses a TCXO temperature-compensated crystal oscillator to avoid frequency shifts caused by temperature changes and the telemetry power is up to 100mW. Check out all our receivers,  as well as the rest of our GEPRC selection. Features 20mmx14mm Small size 1.2g weight WIFI Upgrade firmware ELRS open source project, remote control Maximum refresh rate of 1000Hz Two independent RF receiving links, true diversity receiver The use of a temperature-compensated crystal oscillator (TXCO), no fear of high or low-temperature impact, more stable performance, even if long hours of work is not easy to cause loss of control Built-in PA + LNA, up to 100mW telemetry power Specifications Size: 20x14mm Weight: 1.2g (RX only) Chips: ESP32-PICO-D4, SX1281 Crystal Oscillator: TCXO Frequency Band: 2.4GHz ISM Refresh Rate: 25Hz-1000Hz Input Voltage: 5V Antenna Connector: ipex1 Indicator Light: RGB light TLM Power: 20dBm Binding The factory firmware version of ELRS DUAL 2.4G Diversity Receiver is above 3.x , 3.x and 2.x firmware are not compatible, so the TX module firmware needs to be upgraded to above 3.x before binding. Power on and off the diversity receiver three times with 1 second between each interval continuously to enter the Binding Mode.； RGB indicator flashes twice quickly on the diversity receiver, indicating that the receiver is now in Binding Mode.； Configure remote control or transmitter module to bind with the receiver; If the receiver RGB indicator is solid on, this indicates that the receiver has successfully bound. Includes 1x GEPRC ELRS 2.4GHz Dual RX Diversity Receiver 2x ELRS 2.4GHz Antenna

Read more less

We are glad to introduce a new member of GEPRC FC AIO, the GEP-F722-45A AIO. The F722 AIO adopts MCU STM32F722, which has a powerful performance and higher computing speeds. It has 5 full UART ports and can connect more external devices. We designed a 6-pin connector for the DJI air unit VTX plug-and-play. The BLheili_S 45A ESC can handle 45A continuous current (55A burst), supports the 2-6S lipo battery, and brings the drone a stronger flight performance. It can support OSD parameter adjustment, buzzer, led, and other functions. It is 8.8g, ultra-lightweight, and has a 25.5mm x 25.5mm mounting hole, suitable for most of the frames on the market. GEPRC pursues lighter weight, smaller volume, more functions, and better performance from their flight controllers. Check out all our whoop flight controllers, and our GEPRC products! Features MCU: STM32F722, with strong performance and higher computing speed. It has 5 full UART ports, which can connect more external devices Designed with a 6-pin connector for DJI AIR UNIT MODULE, and just plug and play. The BLheili_S 45A ESC can handle 45A continuous current (55A burst) and supports the 2-6S lipo battery. Support OSD parameter adjustment, buzzer, led, and other functions. 8g ultra lightweight 25mm x 25.5mm mounting hole, suitable for most frames Specifications GEPRC F722 AIO Model Name: GEP-F722-45A AIO MCU: STM32F722 IMU: 42688 gyro/accelerometer(SPI) Firmware target: GEPRC_F722_AIO OSD: Betaflight OSD w/ AT7456Ev UART Ports: R1 T1 / R2 T2 / R3 T3 / R4 T4 / R5 T5 Beeper: YES LED: YES USB: Micro USB BEC output: 5V@1A Integrated LC Filter ESC MCU: 8BB21F16G Continuous current: 45A MAX current: 55A (10s) Input: 2~6S Supports: Dshot600, Oneshot, Multishot BlackBox: 16Mb Target: G_H_30 Size: 32x32mm Board Mounting Hole: 25.5×25.5mm Weight: 8.8g Includes 1 x GEP-F722-45A AIO 1 x XT30-7CM-18AWG Power cables 1 x 35V220UF capacitor 1 x SH1.0-6Pin to GH1.25-8Pin cables 8 x M2*6.5mm Damping rings

Read more less

Replacement aluminum alloy camera plates for GEPRC Mark5 Pro 5" Frame Kit Check out the rest of our 5" Frames & all our GEPRC products!   Includes 1x GEPRC Mark5 5" HD/PRO Replacement Aluminum Alloy Camera Plates (2pc)

Read more less

Replacement arm limit plate for GEPRC Mark5 Pro 5" Frame Kit Check out the rest of our 5" Frames & all our GEPRC products!   Includes 1x GEPRC Mark5 5" HD/PRO Replacement Arm Limit Plate

Read more less

Replacement front bottom plate for GEPRC Mark5 Pro 5" Frame Kit Check out the rest of our 5" Frames & all our GEPRC products!   Includes 1x GEPRC Mark5 5" HD/PRO Replacement Front Bottom Plate

Read more less

Replacement front reinforcement plate for GEPRC Mark5 Pro 5" Frame Kit Check out the rest of our 5" Frames & all our GEPRC products!   Includes 1x GEPRC Mark5 5" HD/PRO Replacement Front Reinforcement Plate

Read more less

Replacement rear bottom plate for GEPRC Mark5 Pro 5" Frame Kit Check out the rest of our 5" Frames & all our GEPRC products!   Includes 1x GEPRC Mark5 5" HD/PRO Replacement Rear Bottom Plate

Read more less

GEPRC Peano antenna is a 5.8G optimized antenna for FPV quad. The antenna has good gain performance and very compact. Working frequency range is 5600-5950 Ghz, with LHCP and RHCP options for multi-player competition. Peano 5.8G antenna also has a variety of connector options. Every antenna has been tested strictly before leaving the factory to ensure good performance. Check out the rest of our antennas, as well as the rest of our GEPRC selection. Features Compact and light-weight design, high quality ABS case for good protection and nice appearance. Options of LHCP and RHCP. Manufactured and tested to highest standards Easy to install, multiple connectors and length options. 50mm Length from end of tube to connector Specifications Frequency Range: 5600-5950MHz Polarization: LHCP/RHCP Gain: 2.5DBi SWR: ≤1.5 Input Impedance: 50Ω Radiation Efficiency: 98% Connector: MMCX 90 Weight: 1.6g~1.8g material: ABS color: transparent grey Includes 2x GEPRC Peano 5.8G Antenna MMCX 90 - Choose Version

Read more less

Introducing... the GEPRC SMART 16 Freestyle Frame Kit! The GEPRC Smart 16 1.6" Nano Freestyle Frame is a tiny, lightweight freestyle FPV addition to the GEPRC Phantom series. The SMART 16 continues the consistent lightweight design concept of the Phantom series. The 1.5mm carbon fiber arm, with a 1mm top plate, creates a balance point that is maintained between the strength of the fuselage and the weight of the whole drone which allows it to be lightweight and tough at the same time. The M1.4 Motors mounting holes can be used to install small 3-hole brushless motors to reduce the weight of the body. Good arm width contributes to high durability. This design is great for freestyle flying, with no props in view! Thanks to the 3D printed parts, the frame weighs only 8.5g, saving a lot of overall weight. The independent battery compartment is designed to stick the battery on top and below the drone making it very convenient and fast to replace batteries. Check out our other Micro frames And our whole GEPRC product line! Specifications Frame Style: Toothpick Top plate thickness: 1.0mm Bottom plate thickness: 1.5mm Camera plate thickness: 1.0mm Stack Size 16x16mm Motor Mount: 6mm Tri 08xx Camera Mount: 14mm Nano Weight: 8.5g (including 3D prints) Recommended:  Motor: GEPRC SPEEDX2 0803 11000Kv Micro Motor AIO: GEPRC F4 V1.4 2-4S AIO Flight Controller Prop: HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack LiPo: RDQ Series 350mah 2S 50C/100C 7.6V HV XT30 Micro Battery Includes 1x GEPRC SMART 16 1.5mm Bottom Plate 2x GEPRC SMART 16 1mm Camera Plate 1x GEPRC SMART 16 1mm Top Plate 2x 120mm LiPo Strap  1x 3D Printed Part Set 1x Screwdriver Set 1x Hardware Set 2x Battery Pad

Read more less

GEPRC SPEEDX2 0802 brushless motor, specially developed for Micro and Whoop FPV, SPEEDX2 motors are enough to meet your needs. GEPRC SPEEDX2 0802 motors have good heat dissipation, lightweight design, and advanced material technology, perfect for Micro and Whoop applications. Specifications Check out all our motors and our GEPRC selection!  Specifications Kv:  17000kv Input Voltage: 1S Configuration:  9N12P Shaft Diameter: 1mm Mounting Pattern: Φ6mm, 3x M1.4 Wire Dimensions:  JST-1.25, 33.5mm  Weight:  2g (w/ wire) Includes 1x GEPRC SPEEDX2 0802 Micro Motor

Read more less

The SPEEDX2 2107.5 brushless motors are the second-generation GEPRC motors designed from scratch. GEPRC SPEEDX2 2107.5 motor is lightweight, has good heat dissipation, and is made of customized high-quality materials. Thanks to the amazing throttle control and advanced engineering design, these motors provide a super smooth flying experience while being super powerful, highly durable, and crash-resistant. SPEEDX2 2107.5  motors are perfect for freestyle and racing FPV pilots. Suitable for a 5-inch frame. Check out our vast brushless motors selection, and our GEPRC selection!  Features High-efficiency and smooth Perfect for Freestyle and Racing FPV Motor dynamic balance, stable operation Best for a 5-inch frame Specifications Model: SPEEDX2 2107.5 Kv: 1960KV/2450KV Configuration: 12N14P Stator Diameter: 21mm Stator Height: 7.5mm Shaft Diameter: Φ4.0mm Size: Φ26.83x30.85mm Rotor: N52H ARC Weight: 29.5g Target: Freestyle & Racing FPV Includes 1 x SPEEDX2 2107.5 motor 1 x M5 Nut 5 x M3x8 Screw 5 x M3x10 Screw

Read more less

GEPRC Goggles pad is crafted with memory foam and skin-friendly nylon mesh fabric for a cozy fit that's compatible with DJI Goggles 2 and Integra. The padding is comfortable to wear and fits a variety of face shapes. Check out our other FPV goggles and accessories,  as well as the rest of our GEPRC selection. Features The sponge foam padding is made of memory foam and skin-friendly nylon mesh fabric, which gently fits the face and is comfortable to wear. It can provide extra cushioning and support to reduce the user’s discomfort when wearing for a long time. This padding can better fix the goggles on the head and ensure the visual stability during the flight. Specification Model: GEPRC Sponge Foam Padding for DJI Goggles 2 Material: memory foam, skin-friendly nylon mesh fabric Weight: 12.8g Includes 1x GEPRC Sponge Foam Padding for DJI FPV Goggles 2 1x Velcro 1x Sticker

Read more less

Introducing the GEPRC Taker F411 8bit 12A AIO Flight Controller, the perfect addition to your mini FPV drone. It is packed with features like ICM-42688-P gyro, 12A ESC support, 2-4S power, and a built-in black box with 16MB flash memory for easy parameter adjustments. Best of all, this AIO comes with a built-in ELRS 2.4GHz receiver with a U.FL connector. Get ready for smooth and precise races and freestyles with this highly-integrated powerful all-in-one flight controller! Check out all our Whoop/AIO Flight Controllers, as well as the rest of our GEPRC selection. Features Bluejay 12A ESC, support 2-4S battery, continuous current 12A, peak current 13A, built-in ammeter SPI ELRS 2.4G receiver  Using STM32F411 FC, the flight control is running stably Using IMU: ICM42688P gyroscope, 8K sampling rate Support buzzer and LED light function With 25.5mm x 25.5mm mounting holes  Specifications  Model: TAKER F411 8Bit 12A AIO  MCU: STM32F411 IMU: ICM42688P Firmware target: GEPRC_F411_SX1280 OSD: BetaFlight OSD w/ AT7456E chip UART Ports: R1 T1\R2 T2 Reverse Port: NR2 Buzzer: YES LED: YES USB Port: Micro USB ESC MCU: BB21F16G Black Box: 16Mb onboard flash memory Continuous Current: 12A Peak Current: 13A Input: 2-4S ESC Protocol: Dshot300, Oneshot, Multishot Current Meter: 210 ESC Firmware: G-H-30 – Bluejay, 0.16, 48kH Size: 31.2 x 31.2mm Board Mounting holes: 25.5mm x 25.5mm hole, M2 hole Weight: 7g ELRS Connector: U.FL Includes  1x GEPRC Taker F411 2-4S AIO Whoop/Toothpick w/12A 8bit 4in1 ESC - ELRS 2.4GHz (SPI) 1x XT30-5.5CM-20AWG power cable 8x M2x6.5mm FC damping grommets (4 each in red/black) 1x 35V220UF capacitor 5x Self-tapping screws (M1.4X5) 1x Instruction manual

Read more less

TinyRadio ELRS Remote Controller is a new generation remote control system developed based on the ExpressLRS open-source project. ExpressLRS sets new standards for long-range connection, low latency, and a maximum refresh rate of 500Hz. The TinyRadio adopts a simplified design to minimize the difficulty of use. It has an ergonomic design, so it is more comfortable to hold. It has a built-in ELRS module, available in 915/868MHz and 2.4GHz versions, and an adjustable power of up to 500mW with a replaceable antenna design. The remote control distance can reach more than 2KM under ideal conditions. The TinyRadio ELRS Controller supports upgrading remote control firmware through a USB interface, and can upgrade the ELRS module firmware through WIFI. Supports wireless connection to computer drone simulator via Bluetooth. It supports two 18650 batteries for ultra-long battery life. 8 low latency channels can meet most of the needs of beginners and professionals. Check out all our RC transmitters! and our GEPRC selection!  Features Built-in ELRS 915MHz/2.4GHz Functional “less is more” design, Easy to carry 2KM+ flight range(subject to the environment) 500mW adjustable power 8 super low latency channels Replaceable antenna Two replaceable 18650 batteries Support USB-C charging Custom remote control system Fully compatible with drone simulators Specifications Size：147x135x71mm (Not including antenna) Weight：223g Adapted Drone Type: Multirotor, Airplane Frequency band：915MHz FCC /868MHz EU /2.4GHz ISM Input voltage：6.6-8.4V Antenna interface: SMA Power：100/250/500mW Channel：8 channel Charging interface: USB-C Firmware upgrade: Support Bluetooth joystick: Support Includes 1 x TinyRadio 1x 18650 tray 1 x Instruction manual Batteries Not Included Tips: TinyRadio ELRS Radio Controller Firmware Upgrade Guide

Read more less