Products
MST 210579, MST RMX 2.0 Rear Motor Conversion Kit
MST RMX 2.0 Rear Motor Conversion Kit
$18.99
Drifting Beast DB-RD-C-001, 1/24 Drifting Beast RWD Drift Car Chassis
DB-RD-C-001, 1/24 Drifting Beast RWD Drift Car Chassis Wheelbase 98-120mm adjustable The newly designed frame db (drifting beast) officially launched in 2022 The whole car adopts a hollow design without a chassis, and adopts the method of lateral support. Although metal materials are used in a large area, because of the large area of hollowing out, the effect of metal lightweight is achieved. The position of the front shock absorber has been changed to the inside of the front of the car, avoiding the interference caused by the maximum steering of the front wheel to the greatest extent. The rear adopts a straight bridge structure. When the center of gravity of the car is shifted, the contact angle between the rear wheel and the ground remains unchanged, and the same grip is always maintained. It can also be changed to a straight axle and a connecting rod. When the center of gravity is shifted, the contact surface between the rear wheel and the ground changes with the shift of the center of gravity. The basic version includes three sets of rear wheel cups, two corresponding to the straight axle mode and one corresponding to the semi-independent mode, so there is no need to buy them separately. The body and the rear gearbox adopt an integrated structure. The main part of the body is made of mirror stainless steel material, and a little polishing treatment will have a mirror effect. There are four types of steering gear arms, large and short, as standard, which basically cover all the mosquito steering gears on the market. 8. Two types of motor bases are equipped as standard, supporting brushed 130 motors and non-inductive brushless, inductive brushless and other motors. The frame does not need to install spacers, and the tightness of the swing arm can be adjusted by the tightness of the screws. The left and right positions of the motor can be fine-tuned, the motor is centered, bid farewell to the effect of the crooked motor, and cure players with obsessive-compulsive disorder. The rear straight axle wheel cup is adjustable, and the inner and outer eight can be adjusted at will. In the later stage, a telescopic dog bone will be introduced, and the rear wheel base can be adjusted without replacing the wheel hub. This product was added to our catalog on June 14, 2023
$199.99
HobbyWing Hobbywing Xerun XD10 Pro Drift Spec Brushless Speed Controller
Hobbywing Xerun XD10 Pro Drift Spec Brushless Speed Controller Features: Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages. A separate PRG/FAN port is able to power an external fan to maximize cooling performance or connect an LCD program box or WiFi module to the ESC. Variable frequency regulation of PWM & brake frequencies allows users to precisely regulate the driving & braking forces (of the motors). Multiple protections: low-voltage cutoff protection, ESC and motor thermal protection, and fail-safe (throttle signal loss protection), reverse polarity protection (the external standard cap pack will still be damaged if battery reversal occurs). Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real-time. Firmware upgrade via Hobbywing multifunction LCD program box (PC only) or OTA Programmer (item sold separately) Specifications: Application: 1/10th drift car Cont./Peak Current: 100A/800A Input Voltage: 2S LiPo/4-6S NiMH BEC Output: 5-7.4V Adjustable, Continuous Current of 5A (Switch-mode) Wires & Connectors: 13AWG 200mm Programming device: LCD program box, OTA programmer (Available through Firmware update) Firmware: LCD Program box via USB software (PC only), OTA (iOS / Android) Size & Weight: 40.7x35.0x32.0mm (w/Fan) Weight: 95g (w/ wires) Motor Limit: 2S LiPo/6S NiMH ?8.5T Includes: (1) XD10 PRO ESC (2) Input wires & (3) Output wires (PRE-SOLDERED) (1) cooling fan Decals Bonus parts: heat tubes, double tape, nylon cable zap traps This product was added to our catalog on May 3, 2023
$220.99
HPI Racing HPI115984, HPI RS4 Sport3 Drift RTR Ford Mustang Vaughn Gittin Jr. Body Sedan
HPI115984, HPI RS4 Sport3 Drift RTR Ford Mustang Vaughn Gittin Jr. Body Sedan RS4 Sport 3 Drift Vaughn Gittin Jr. Fun-Haver Ford Mustang RTR The RS4 Sport 3 line-up is expanding with Vaughn Gittin Jr's competition-spec Ford Mustang straight out of his RTR tuning garage! Combining the fabulous driving of the RS4 Sport 3 with its 4WD drivetrain and replica Nitto tires is a no-brainer, and when topped with Vaughn's distinct black and silver livery, it's a one-of-a-kind combination! The fully tunable suspension lets you tweak and tune to your heart's content so you can be your own drift car mechanic, or you can just run with the standard settings - they're preset to be great on all driving surfaces! The RS4 Sport 3 package is fully built, painted and detailed right out of the box, and fitted with a realistic steering wheel style 2.4GHz radio system - all you have to do is plug in the included batteries for all-day drift action! Features: One-Piece Molded Chassis Low Profile Layout Design 2s LiPo Ready Full-Time Four-Wheel Drive Sealed Shaft Drivetrain Bottom-Access Driveshaft Easy Access Differentials 4-Gear Metal Diffs Double-Wishbone Fully Adjustable Suspension Multiple Shock Positions Oil Filled Threaded Shocks Tough Front End Suspension Tunable Rear Suspension Double Bellcrank Steering Rugged Spring-Loaded Servo Saver Aluminum Motor Mount Rear End Chassis Diffuser Rubber-Sealed Ball Bearings Adjustable Height Body Mounts Specifications: Motor: Fireball 15T Brushed ESC: SC-3S WP2 Length: 431mm (17") Height: 127mm (5") Width: 200mm (7.9") Wheelbase: 254mm (10") What's In The Box: (1) HPI RS4 Sport3 Drift - RTR (1) Ford Mustang Vaughn Gittin Jr. Body (1) HPI TF-40 2.4Ghz Radio System (1) Wall Charger - for 7.2V NiMh Battery w/Tamiya Connector (1) 7.2V 2000mAh NiMh Battery (4) AA Batteries (1) Parts Package - Tuning Parts This product was added to our catalog on May 27, 2022
$299.99
HPI Racing HPI120091, HPI E10 Drift Fail Crew Nissan Skyline R34 GT-R Assembled RTR
HPI120091, HPI E10 Drift Fail Crew Nissan Skyline R34 GT-R Assembled RTR E10 Drift Fail Crew Nissan Skyline R34 GT-R, Ready To Run with Battery & Charger The full-size version is driven by Russian Fail Crew member and FIA drifting champion Arkady Tsaregradtsev, and now you have the opportunity to take the champion's ride for a spin! Fail Crew is an international crew of pilots that has secured its top rating position at the most prestigious drifting competitions. If you're up against anyone from Fail Crew on the track, be prepared to - yes, fail! Every crew member's automobile is an object of modern art on wheels designed by famous Russian artist Ciay The E10 was designed so anyone can take the wheel and go for a spin! Arriving right out of the box in Ready-To-Run (RTR) form with a fully painted body and a preassembled chassis, it's a simple matter of "charge and go" for hours of fun! The RTR E10 includes a high-performance electric motor, plus a waterproof electronic speed controller that features proportional throttle, powerful brakes and convenient reverse functions, allowing it to drive and maneuver just like real cars. An intuitive steering wheel style transmitter with real steering wheel and trigger style throttle/brake controls takes care of the controller duties. Features, looks, performance and price: the RTR E10 Drift is one of the easiest ways ever to experience the fun and excitement of driving an RC drift car! Features: Officially authorized replica of Fail Crew Nissan Skyline R34 GT-R Drift Car Fully assembled E10 drift car chassis SC-3sWP2 Waterproof Electronic Speed Control with Reverse 2.4 GHz radio system for crystal-free, comfortable control 7.2v 2000 mAh NiMH Rechargeable HPI Plazma battery High torque Saturn 27T 540 motor Specifications: Length: 14.8" (375mm) Width: Adjustable 7.32", 7.56", 7.80" (186, 192, 198mm) Wheelbase: 10" (255mm) Weight: 2.8lbs. w/o body (1280g) Drive System: Shaft Drive 4WD Drive Ratio: 7.48:1 This product was added to our catalog on November 30, 2021
$249.99
HPI Racing HPI120094, HPI Sport 3 Drift VGJR "Fun Haver" Ford Mustang 1/10 RTR 4WD Drift Car (V2) w/2.4GHz Radio, 7.2V Battery & Charger
HPI120094, HPI Sport 3 Drift VGJR "Fun Haver" Ford Mustang 1/10 RTR 4WD Drift Car (V2) w/2.4GHz Radio, 7.2V Battery & Charger HPI Sport 3 Vaughn Gittin Jr Ford Mustang 1/10 RTR Drift Car The HPI Sport 3 Drift Vaughn Gittin Jr's "Fun Haver" Ford Mustang 1/10 RTR Touring Car has been designed to give the Formula Drift looks and feel. This high performance Sport 3 chassis comes with officially licensed Nitto NT555 G2 tires on Tech 7 wheels. The 1/10 drift chassis is equipped with high octane HPI Firebolt 15T Brushed Motor paired with a brushed ESC. The fully-independent double wishbone suspension uses adjustable, oil-filled shocks to keep the Sport 3 ready for any road condition. The officially licensed, super realistic Ford Mustang RTR replica features a wild color scheme emblazoned with Vaughn's signature Fun-Haver logos and his "Ready to Rock" motto. The Fun-Haver V2 is packed with tough features to make it super-easy to drive for hours of sideways fun! Features: One-Piece Molded Chassis Low Profile Layout Design Brushless Capable Drivetrain Full-Time 4WD Sealed Center Driveshaft Easy Access Differentials 4-Gear Metal Differentials Adjustable Double-Wishbone Suspension Threaded Oil-Filled Shocks Double Bellcrank Steering Aluminum Motor Mount Specifications: Scale: 1/10 Length: 431mm (17") Width: 200mm (7.9") Height: 127mm (5") Wheelbase: 254mm (10") Includes: (1) HPI Sport 3 Vaughn Gittin Jr Ford Mustang 1/10 RTR Drift Car (1) 7.2V 2000mAh NiMH Battery (1) Wall Charger (4) AA Batteries for Transmitter Needed to Complete: Nothing! Everything you need is in the box! This product was added to our catalog on April 21, 2023
$299.99
HPI Racing HPI120096, HPI RS4 Sport 3 Dai Yoshihara Subaru BRZ 1/10 RTR 4WD Electric Drift Car w/2.4GHz Radio, 7.2V Battery & Charger
HPI120096, HPI RS4 Sport 3 Dai Yoshihara Subaru BRZ 1/10 RTR 4WD Electric Drift Car w/2.4GHz Radio, 7.2V Battery & Charger The HPI RS4 Sport 3 Dai Yoshihara Subaru BRZ 1/10 4WD Electric Drift Car has been designed to give you the looks of a true Formula D machine with the ease of handling found in the RS4 Sport 3. This detailed Subaru BRZ body features Dai's official Turn 14 Distribution race livery in its unique blue, black and silver finish. Under the hood, this 1/10th scale Subaru is built on the popular HPI RS4 Sport 3 chassis. With full-time shaft-driven 4WD, a fully sealed drivetrain, waterproof 2.4 GHz electronics/radio gear, fully independent double wishbone suspension and adjustable oil filled shocks, you'll be ready to shred in any condition. Features: One-Piece Molded Chassis Low Profile Layout Design Brushless Capable Drivetrain Full-Time 4WD Sealed Center Driveshaft Easy Access Differentials 4-Gear Metal Differentials Adjustable Double-Wishbone Suspension Threaded Oil-Filled Shocks Double Bellcrank Steering Aluminum Motor Mount Specifications: Scale: 1/10 Length: 431mm (17") Width: 200mm (7.9") Height: 127mm (5") Wheelbase: 254mm (10") Includes: (1) HPI RS4 Sport 3 with Dai Yoshihara Subaru BRZ Body Shell (1) 7.2V 2000mAh NiMH Battery (1) Wall Charger (4) AA Batteries for Transmitter Needed to Complete: Nothing! Everything you need is in the box! This product was added to our catalog on March 24, 2022
$289.99
HPI Racing HPI120097, HPI Sport 3 James Deane Nissan S15 1/10 4WD Electric Drift Car w/2.4GHz Radio, 7.2V Battery & Charger
HPI120097, HPI Sport 3 James Deane Nissan S15 1/10 4WD Electric Drift Car w/2.4GHz Radio, 7.2V Battery & Charger The tunable suspension of the RS4 Sport 3 lets you tweak and tune to your heart's content, so you can be your own drift car mechanic, or you can just run with the standard settings - they're preset to be great on all driving surfaces! The RS4 Sport 3 package is fully built, painted and detailed right out of the box, and ships with a realistic steering wheel style 2.4GHz radio system - all you have to do is plug in the included batteries for easy drift action!Replica Nissan S15 BodyThe Nissan S15 Silvia is one of the most popular cars chosen to build into a drift racer, thanks to a finely tuned rear-wheel drive chassis and huge amount of aftermarket tuning potential to its engine and drivetrain. With our officially licensed replica body, it's easy to turn the RS4 Sport 3 into a realistic drift racer! Our Nissan S15 body features James Deane's official Worthhouse Drift Team race livery, from its front splitter all the way to the back bumper. It's pre-painted and detailed to look just like the Formula D champ's real ride straight out of the box!Finishing off the car is a complete set of brand new replica 7Twenty wheels in a cool silver finish, each one wrapped with official replica Falken Azenis RT615 T-Drift Tires. These low-profile drift-specific tires are made for high-performance, realistic drift action at 1/10th scale! With a super stiff, hard plastic construction, HPI drift tires are the ideal way to get drifting quickly and easily.It's easy to replicate both cars on the Worthouse drift team, too: alternate stickers included in every kit allow you to turn your RS4 Sport 3 into a replica of James' teammate, Piotr Wiecek! Whichever driver you choose to race as, with a full set of sponsor logos adorning the car (including HPI Racing logos!) it's an instant head-turner! Features: Encased pinion & spur gear Sealed metal gear diffs capable of handling brushless power Waterproof SC-3SWP2 speed controller Battery box fits standard LiPo batteries & up to 7-cell NiMH Battery position is adjustable for extra traction or increased steering Thick hook-and-loop strap holds battery in place Enclosed receiver case protects from the elements Double-wishbone suspension design Composite oil-filled threaded shock absorbers Complete set of ball bearings Fully enclosed 4WD shaft drive
$359.99
HPI Racing HPI120098, RS4 Sport 3 Flux Ford GT LM Heritage Edition Brushless RTR
One of the definite "retro classics" of the modern supercar era has been the Ford GT, and now it comes to the RS4 Sport 3 chassis in the ultimate classic racing livery of the Gulf Racing colors! Fitted with color-matching wheels, this car is an immediate head-turner and is ready to hit amazing top speeds thanks to its FLUX power! A powerful 4000KV brushless motor can power the car to speeds over 60 mph (100km/h), all you need to provide is a suitable car battery and charger!
$454.99
HPI Racing HPI120101, Micro RS4 Drift Fail Crew Nissan Skyline R34 GT-R RTR Ready To Run w/ Battery & Charger
HPI120101, Micro RS4 Drift Fail Crew Nissan Skyline R34 GT-R RTR Ready To Run w/ Battery & Charger
$199.99
HPI Racing HPI120103, HPI S&D-RS4 Sport 3 Warsteiner BMW M3 E30 RTR, 1/10, 4WD, w/2.4GHz Radio System, Battery & Charger-Box D
HPI120103, HPI S&D-RS4 Sport 3 Warsteiner BMW M3 E30 RTR, 1/10, 4WD, w/2.4GHz Radio System, Battery & Charger-Box D HPI is delighted to offer this RS4 Sport 3 BMW M3 E30 draped in the famous BMW Warsteiner livery and a tribute to the Schnitzer Motorsport machine piloted by Roberto Ravaglia to many years of success. Every true Touring Car fan will know the name Roberto Ravaglia. Roberto is one of the most successful racing drivers of this era, and winner of seven titles in four different championships. Every detail of his World beating 1987 car has been replicated for this Warsteiner edition. Under the hood is the tried and tested, RS4 SPORT 3 platform RC fans know and love, fully tunable and ready to race, right out of the box! General Features: Pre-assembled 1/10th scale RS4 Sport 3 on-road car chassis One-piece molded composite chassis Low profile chassis design for low center of gravity Full-time 4WD for excellent control Extra-strong metal-gear drivetrain ready for 3S LiPo Chassis accepts 6 or 7-cell NiMH or 2-3S LiPo battery packs Adjustable battery position for more steering or more acceleration Enclosed receiver box protects the radio receiver Cam-type cast finned aluminum motor mount Fully enclosed drivetrain and differentials Efficient and tough shaft drivetrain Tough oil-filled 4-gear metal-gear differentials Double-wishbone adjustable racing suspension Racing-derived C-hub front suspension Oil-filled coil-over shocks with adjustable ride height Easy access to all critical maintenance points Dual bellcrank steering for precise steering control Cam-type spring-loaded servo saver Durable foam bumper protects the car chassis and body Adjustable body post mounts to allow most 190mm and 200mm wide bodies to fit 12mm hex hubs fit all available touring car wheels All hex head hardware for easy car maintenance Full set of metal-shielded ball bearings for maximum efficiency Comprehensive instruction manual for easy maintenance Pre-Cut Factory Finished And Decaled Bodyshell Sport 3 Features: 15T Firebolt 540 Brushed Motor Waterproof ESC and Water-Resistant Servo 2.4GHz Radio Set with Waterproof Receiver Spec-Grip Performance Tires Replica BBS RS Mesh Wheels Includes: 4x AA Batteries for Transmitter 2000mAh NiMH 7.2V Battery & AC Charger for Car Features: ESC: SC-3SWP2 Waterproof Electronic Speed Control Motor: Firebolt 15T Motor (540 Type) Servo: HPI SS-20WR Servo (Water-Resistant/6.0V/6.5KG/Plastic Geared) Radio: HPI TF-41/RF-41WP 2.4Ghz Radio Set Battery: HPI Plazma 7.2V 2000mAh Nimh Stick Pack Charger: AC Multi-Regional Charger with Standard Plug Specifications: Length (mm): 431 Width (mm): 200 Height (mm): 127 Wheelbase (mm): 254 This product was added to our catalog on November 29, 2023
$299.99
HPI Racing HPI160375, HPI Sport 3 Flux Ford Mustang Mach-e 1400 1/10 RTR Brushless Touring Car
HPI160375, HPI Sport 3 Flux Ford Mustang Mach-e 1400 1/10 RTR Brushless Touring Car The HPI Sport 3 Flux Ford Mustang Mach-e 1400 1/10 RTR Electric Touring Car has been designed to give you the looks of a real sports hatchback. The detailed Ford Mach-e Mustang body features the unique front styling and large rear wing. Under the hood, this 1/10th scale Ford is built on the popular HPI RS4 Sport 3 Flux chassis. With full-time shaft-driven 4WD, a fully sealed drivetrain, waterproof 2.4 GHz electronics/radio gear, fully independent double wishbone suspension and adjustable oil filled shocks, you'll be ready to shred in any condition. Features: One-Piece Molded Chassis Low Profile Layout Design HPI Flux Brushless System Full-Time 4WD Sealed Center Driveshaft Easy Access Differentials 4-Gear Metal Differentials Adjustable Double-Wishbone Suspension Threaded Oil-Filled Shocks Double Bellcrank Steering Aluminum Motor Mount Specifications: Scale: 1/10 Length: 431mm (17") Width: 200mm (7.9") Height: 127mm (5") Wheelbase: 254mm (10") Includes: (1) HPI Sport 3 Flux Ford Mustang Mach-e 1400 (4) AA Batteries for Transmitter Needed to Complete: (1) 2S or (1) 3S LiPo Battery Pack with T-plug Compatible Lipo Battery Charger This product was added to our catalog on March 24, 2023
$379.99
HPI Racing HPI160422, HPI Sport 3 Drift BMW E30 Driftworks 1/10 RTR 4WD Drift Car w/2.4GHz Radio, 7.2V Battery & Charger
HPI160422, HPI Sport 3 Drift BMW E30 Driftworks 1/10 RTR 4WD Drift Car w/2.4GHz Radio, 7.2V Battery & Charger The HPI Sport 3 Drift BMW E30 Driftworks 1/10 RTR 4WD Drift Car. This Sport 3 Drift features the ultra-cool BMW M3 painted body, complete with extra-wide wheel arches, a front air dam and a big street style rear wing! The car is also fitted with replica Work Emotion XC8 wheels wrapped with officially licensed Toyo Proxes tires for extreme scale realism. The 1/10 drift chassis is equipped with high octane HPI Firebolt 15T Brushed Motor paired with a brushed ESC. The fully-independent double wishbone suspension uses adjustable, oil-filled shocks to keep the Sport 3 is ready for any road condition. This officially licensed, super realistic BMW E30 RTR replica is equipped with everything needed for you to get sideways right out of the box, including the AA batteries! Features: One-Piece Molded Chassis Low Profile Layout Design Brushless Capable Drivetrain Full-Time 4WD Sealed Center Driveshaft Easy Access Differentials 4-Gear Metal Differentials Adjustable Double-Wishbone Suspension Threaded Oil-Filled Shocks Double Bellcrank Steering Aluminum Motor Mount Specifications: Scale: 1/10 Length: 431mm (17") Width: 200mm (7.9") Height: 127mm (5") Wheelbase: 254mm (10") Includes: (1) HPI Sport 3 Drift BMW E30 Driftworks 1/10 RTR 4WD Drift Car (1) 7.2V 2000mAh NiMH Battery (1) Wall Charger (4) AA Batteries for Transmitter Needed to Complete: Nothing! Everything you need is in the box! This product was added to our catalog on March 28, 2022
$299.99
HobbyWing HWA30108000, Hobbywing Quicrun 10BL60 Sensored Brushless ESC
HWA30108000, Hobbywing Quicrun 10BL60 Sensored Brushless ESC Features: High performance but low price- users can own this reliable race-ready ESC at an affordable cost. Compact size, suitable for various car chassis. Auto identification system can recognize sensored or sensorless brushless motors automatically. Smooth operation and plentiful adjustment options. Suitable for most kinds of competitions. 8 steps of timing adjustment greatly increase the output power of the motor and unlock its maximum potential. Proportional brake with 4 steps of Maximum Brake Force adjustment, 8 steps of Drag Brake Force adjustment and 4 steps of Initial Brake Force adjustment. 9 steps of acceleration (punch) adjustment, from “soft” to “very aggressive” to fit various of cars, tires and tracks. Multiple protections: Low voltage cut-off protection for LiPo or NiMH battery / Over-heating protection / Throttle signal loss protection / Motor Lock-up protection. One-button sets the ESC. Easily reset all parameters to factory default settings. Compatible with optional device ---- the portable Digital LED Program Card, especially convenient for outdoor use. Specifications: Applications: 1/10 & 1/12 On-road / Off-road / F1 / Drift car race / Street race for fun / Club racing / STOCK race with 0 timing / Drift car race Cont./Peak Current/Resistance: 60A/380A/0.0008? Motor Type Supported: Sensored / Sensorless Brushless Motor Car Applicable: 1:10 On-road/Off-road/Buggy/Monster Motor Limit: 2S LiPo or 4-6 cell NiMH: ?8.5T(1/10 On-road), ?13.5T(1/10 Off-road)* 3S LiPo or 8-9 cell NiMH: ?13.5T(1/10 On-road), ?17.5T(1/10 Off-road)* Battery: 4-9 cell NiMH, 2-3S LiPo BEC Output: 6V/2A (Linear Mode) Size: 33mm(L)*28mm(W)*31.5mm(H, with cooling fan) Weight: 59g (with wires, without cooling Fan) External Program Port: Available *NOTE: Indicates the limit value of motor turns when the ESC timing is set to 0. The larger the timing, the more turns the motor needs. This product was added to our catalog on May 3, 2023
$54.99
HobbyWing HWA30112613, Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC (Stealth)
HWA30112613, Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC (Stealth) The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC is great for giving the user all the tuning options needed for competitive racing. This Stealth edition is given the Hobbywing FFD (Frameless Fan Design) system for extreme ESC cooling. Get the XR10 G2S and experience true motor control. Hobbywing FFD: A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. PWM Adjustments: From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition. Internal BEC: The internal BEC is a switching design and provides up to 10A of power. Adjustable from 5-7.4V, this ESC is designed to handle the most power hungry of servos. NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended. Features: 32 Bit, M4 microprocessor for ultimate performance Frameless fan design for extreme cooling Reverse polarity protection Precise adjustments to throttle and brake PWM Optimized programmable parameters Extended brake force Drag Brake Acceleration and Softening Function High output BEC Specifications: Wire gauge: 13 AWG Lightweight Ultra-flex Application: 1/10th Touring car & Buggy racing, 1/10th drift car and F1 Continuous Current: 160A Peak Current: 1200A Input Voltage: 2S LiPo / 4-6S Cell NiMH BEC Output: BEC voltage of 5-7.4V Programming device: LCD Program Box / OTA Programmer Firmware: LCD Program box via USB software (PC only) / OTA (iOS / Android) Size & Weight: 37.5x30.9x32.5mm (with Fan & Fan Shroud) Weight: 88g (with wires) Motor spec recommendation: Touring Car: >4.5T Buggy: >5.5T Includes: (1) Xerun XR10 Pro G2S 160A Sensored Brushless ESC (1) Cooling Fan (1) Capacitors Decals Accessory package This product was added to our catalog on December 14, 2023
$224.99
HobbyWing HWA30125002, HobbyWing QuicRun 10BL120 G2 120A 1/10 Sensored Brushless ESC
HWA30125002, HobbyWing QuicRun 10BL120 G2 120A 1/10 Sensored Brushless ESC This product was added to our catalog on December 14, 2023
$49.99
HobbyWing HWA30401134, Hobbywing Xerun D10 Drift Brushless Motor (10.5T) (Black)
HWA30401134, Hobbywing Xerun D10 Drift Brushless Motor (10.5T) (Black) Features: Designed for Drift: The Xerun D10 motors provide the ideal colors to perfectly match your drift machines. Available in Black, Red, and Purple. Banana Plug Quick-Swap Design: The motor comes factory soldered with high quality 3.5mm banana plug for easy access swap to different motors. 3.5mm male head is also included in the XD10 ESC. Stator Designed for Drift: The motor stator is optimized for drift and improves motor efficiency in drift applications. Built-in with high-precision sensors board, combined with drift-specific fan rotors, providing excellent motor linearity and drivability while greatly improves motor efficiency. Lightweight: The 10.5T motor weighs approximately 158g while the 13.5T is at 165g (including 3 gold insert weights). The lightweight motor allows user to easily tweak their weight bias on their car. Fan Rotor: Providing great heat dissipation, power the special-shaped gold fan on the rotor heats the motor while making a pleasant sound, especially when Turbo is turned on. Best paired with XD10 PRO ESC Specifications: Application: 1/10th Drift car Input Voltage: 2S Lipo KV: 4600kv Rotor: 2 POLE ?7-12.2*24.1-BUT*-L1 Weight: 157 Can Size: 35.7xx52.6mm (1.41x2.07") Shaft Diameter: 3.175mm (0.125") Shaft Length: 15.0mm (0.591") NOTE: To avoid short circuits, ensure that all wires and joints must be well insulated before connecting the motor to related devices. The M3 screws with a length (no longer than 7mm) are needed when mounting the motor onto your vehicle. Please pay attention to the relevant marks (on the ESC) when soldering/connecting those output wires to the motor and make sure that you will strictly follow the wiring order (between the ESC & the motor) of “A-A, B-B, and C-C”. Please ensure the sensor cable is clean and undamaged when you’re using a sensor ESC. You need to pay attention to the two connectors on the cable when connecting the ESC to the motor. Re-check all the connections between the ESC & the motor and ensure that they are all correct before turning on the ESC. Timing Note: The D10 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing. You can adjust the motor timing after unfastening the screw on the rear end-plate. Please adjust the timing as needed according to the mark (white lines) at the rear end of the motor and fasten the screw after the adjustment. For obtaining optimal performance, you can change the output range and characteristics of your power system by adjusting the motor timing. Increasing the timing can increase the motor speed (RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing usually requires a high(er) ratio. Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the user manual of the ESC. After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about the motor temperature via a infra-red temperature gun. If the temperature is too high, please let the motor cool down first and then test again. If the temperature is still too high, then please reduce the timing or increase the FDR (that is to replace the pinion gear with fewer teeth or spur gear with more teeth). This product was added to our catalog on May 3, 2023
$120.99
HobbyWing HWA30401139, HobbyWing Xerun D10 Drift Brushless Motor (13.5T) (Purple)
HWA30401139, HobbyWing Xerun D10 Drift Brushless Motor (13.5T) (Purple) Features: Designed for Drift: The Xerun D10 motors provide the ideal colors to perfectly match your drift machines. Available in Black, Red, and Purple. Banana Plug Quick-Swap Design: The motor comes factory soldered with high quality 3.5mm banana plug for easy access swap to different motors. 3.5mm male head is also included in the XD10 ESC. Stator Designed for Drift: The motor stator is optimized for drift and improves motor efficiency in drift applications. Built-in with high-precision sensors board, combined with drift-specific fan rotors, providing excellent motor linearity and drivability while greatly improves motor efficiency. Lightweight: The 10.5T motor weighs approximately 158g while the 13.5T is at 165g (including 3 gold insert weights). The lightweight motor allows user to easily tweak their weight bias on their car. Fan Rotor: Providing great heat dissipation, power the special-shaped gold fan on the rotor heats the motor while making a pleasant sound, especially when Turbo is turned on. Best paired with XD10 PRO ESC Specifications: Application: 1/10th Drift car Input Voltage: 2S Lipo KV: 2900kv Rotor: 2 POLE ?5-12.1*24.1-BES*-L3 Weight: 157 / 165 Can Size: 35.7xx52.6mm (1.41x2.07") Shaft Diameter: 3.175mm (0.125") Shaft Length: 15.0mm (0.591") NOTE: To avoid short circuits, ensure that all wires and joints must be well insulated before connecting the motor to related devices. The M3 screws with a length (no longer than 7mm) are needed when mounting the motor onto your vehicle. Please pay attention to the relevant marks (on the ESC) when soldering/connecting those output wires to the motor and make sure that you will strictly follow the wiring order (between the ESC & themotor) of “A-A, B-B, and C-C”. Please ensure the sensor cable is clean and undamaged when you’re using a sensor ESC. You need to pay attention to the two connectors on the cable when connecting the ESC to the motor. Re-check all the connections between the ESC & the motor and ensure that they are all correct before turning on the ESC. Timing Note: The D10 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing. You can adjust the motor timing after unfastening the screw on the rear end-plate. Please adjust the timing as needed according to the mark (white lines) at the rear end of the motor and fasten the screw after the adjustment. For obtaining optimal performance, you can change the output range and characteristics of your power system by adjusting the motor timing. Increasing the timing can increase the motor speed (RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing usually requires a high(er) ratio. Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the user manual of the ESC. After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about the motor temperature via a infra-red temperature gun. If the temperature is too high, please let the motor cool down first and then test again. If the temperature is still too high, then please reduce the timing or increase the FDR (that is to replace the pinion gear with fewer teeth or spur gear with more teeth). This product was added to our catalog on April 21, 2024
$119.99
HobbyWing HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T)
HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T) The Hobbywing Quicrun 3650 G2 Sensored Brushless Motor is a high efficiency option, creating good power, and keeping temps low. Ideal for 1/10th, 1/12th On-road (Race or drift Touring cars, F1, M vehicles and etc.) & Off-road (Buggies/2WD SCTs & Trucks) STOCK/SPORT Class Competitions (About Motors' T counts, please refer to rules regulated by race organizers), Beginners for practice, and Rock Crawlers (applicable to 21.5T,25.5T motors) applications. Features: Built-in Hall sensor brings drivers an amazing sense of control. Top-quality components: heat-resistant magnet, heat-resistant wires and name-brand bearings. Dustproof design where motor leads exit. Features a gold-plated lockable connector which can be fastened by screws, eliminating the possibility of losing connections. Detachable structure is easy to clean and maintain, greatly prolonging the service life of the motor. Specifications: Turn: 21.5T Kv: 1800Kv LiPo: 2-3S Shaft Diameter: 3.175mm Resistance: 0.0747 ohm No Load Current: 1.3A Max Output Power: 95W Max Output Current: 28A Weight: 186g This product was added to our catalog on May 3, 2023
$54.99
HobbyWing HWA30408012, Hobbywing XERUN Justock 3650 SD G2.1 Sensored Brushless Motor (21.5T)
HWA30408012, Hobbywing XERUN Justock 3650 SD G2.1 Sensored Brushless Motor (21.5T) The Hobbywing XERUN Justock 3650 SD G2.1 Sensored Brushless Motors feature an updated can design over the G2 - and especially G1 - and push the boundaries of an Fixed Timing Motor with lower weight, good heat dissipation and a rebuildable design. Features: The use of a heat-resistant magnet attached aluminum case and double insulated windings, high precision bearings, and rotor with a strong structure guarantees outstanding performance and super durability. The built-in Hall sensor non-adjustable end bell combined with a high precision and balanced rotor guarantees the user a smooth and linear power on demand. The silicon O-ring seal fitted between the end bell and stator helps to conduct inner heat to the motor case and prevent dust from entering the HALL sensor. The detachable structure design for daily cleaning and maintenance can effectively prolong the service life of this Justock motor and improve its operating efficiency. This motor is perfectly matched with the XR10-Justock ESC for all zero timing spec racing and also compatible with other Hobbywing Electronic Speed Controllers including other brands. This Justock motor is applicable to various 1/10th, 1/12th on-road & off-road vehicles. It can be an ideal choice for Stock or Sport class races but can also be a nice choice for newbies for practice. The motor design is in compliance with IFMAR, and ROAR specifications. Specifications:Scale: 1/10, 1/12Brushless: YesSensored: YesPole Count: 2KV Rating: 2050LiPo Cells: 2-3SNo-Load Current(A): 3Outer Diameter: 35.9mm (1.413")Length: 52.5mm (2.067")Shaft Diameter: 3.17mm (0.125")Weight: 175g (6.17oz)Timing: FixedApplications: STOCK/SPORT class (choose the motor as per competition rules) of 1/10th , 1/12th On-road (i.e. competition touring car or drift, F1, Mini car, and etc.) and Off-road (i.e. buggy, 2WD SCT & truck) racing, Normal Training, and Rock Crawlers (21.5T & 25.5T only). This product was added to our catalog on May 3, 2023
$64.99
HobbyWing HWI30404307, HobbyWing Quicrun 3650 G2 Sensored Brushless Motor (21.5T)
HWI30404307, HobbyWing Quicrun 3650 G2 Sensored Brushless Motor (21.5T) The Hobbywing Quicrun 3650 G2 Sensored Brushless Motor is a high efficiency option, creating good power, and keeping temps low. Ideal for 1/10th, 1/12th On-road (Race or drift Touring cars, F1, M vehicles and etc.) & Off-road (Buggies/2WD SCTs & Trucks) STOCK/SPORT Class Competitions (About Motors' T counts, please refer to rules regulated by race organizers), Beginners for practice, and Rock Crawlers (applicable to 21.5T,25.5T motors) applications. Features: Built-in Hall sensor brings drivers an amazing sense of control. Top-quality components: heat-resistant magnet, heat-resistant wires and name-brand bearings. Dustproof design where motor leads exit. Features a gold-plated lockable connector which can be fastened by screws, eliminating the possibility of losing connections. Detachable structure is easy to clean and maintain, greatly prolonging the service life of the motor. Specifications: Turn: 21.5T Kv: 1800Kv LiPo: 2-3S Shaft Diameter: 3.175mm Resistance: 0.0747 ohm No Load Current: 1.3A Max Output Power: 95W Max Output Current: 28A Weight: 186g This product was added to our catalog on April 21, 2024
$64.99
KYOSHO KYO34471T1, Kyosho EP Fazer Mk2 FZ02-D Toyota Supra A80 ReadySet (White/Black/Red) w/Syncro KT-231P+
KYO34471T1, Kyosho EP Fazer Mk2 FZ02-D Toyota Supra A80 ReadySet (White/Black/Red) w/Syncro KT-231P+ Toyota Supra A80 with Kyosho original graphics. Next generation chassis with improved durability, performance, maintenance, and friendly features. Features: Fazer Mk2 Chassis FZ02. Shorter wheel wheel-base compared to the FZ02L (Dodge Challenger) chassis. Simple and efficient shaft driven 4WD design with improved performance. Light weight and low CG bathtub style design made of durable glass reinforced 66 nylon material. Licensed Toyota Supra A80 Body New wheel design with brake rotor parts!. Also includes 0mm offset rotor hubs (Allowing 190mm width) Drift Tires New steering and double wishbone suspension design for superior handling and damping characteristics. Adjustable caster angle(3 settings) 12mm big bore shock Reliable shaft driven 4WD drivetrain design with slipper clutch 2 bevel gear type diff system on front and rear Easy gear mesh system Powerful Kyosho original 550 size 14T brushed motor Kyosho Speed House KA060 91W water proof brushed 60A ESC with Super plug connectors. 2S Li Po compatible. High response, high torque KS 4081 04 WP water proof steering servo New shock design and soft shock spring setup New RX box to protect from dust and debris Syncro 2.4GHz KT2 31P Radio system All hex hardware Full ball bearings Specifications: Length: 455mm Width: (Body width) 200mm (210mm) Height: 120mm Wheelbase: 260mm Tread Front/Rear: 174mm/174mm Tires Front/Rear: 64×24.2mm/64×24.2mm Gear Ratio: 6.54:1 Weight: 1650g (approx.) Transmitter: Syncro KT-231P+ Motor: G14L Includes: Completed chassis with R/C radio installed Factory assembled body complete with color scheme Syncro KT-231P+ transmitter Installed 60A waterproof ESC (forward/brake/reverse) Hex wrench Spanner Needed to Complete: Battery for Chassis w/T-Plug Connector Charger (4) AA size batteries for transmitter This product was added to our catalog on October 19, 2021
$219.99
KYOSHO KYO34472T1, Kyosho Fazer Mk2 FZ02 2005 Ford Mustang GT-R Drift ReadySet
KYO34472T1, Kyosho Fazer Mk2 FZ02 2005 Ford Mustang GT-R Drift ReadySet w/Syncro KT-231P+ The Kyosho Fazer Mk2 FZ02 2005 Ford Mustang GT-R ReadySet was created for the pure enjoyment of R/C car driving. The combination of a beautifully reproduced car body with the FAZER series chassis can’t be beaten. Kyosho has taken its standard touring car chassis and given it a full model makeover that has evolved performance. A simplified design with fewer parts simplifies maintenance and reduces weight, while core strength and rigidity has been increased through updated materials and ribbing/stiffeners on front and rear. In addition, the symmetrical chassis design offers excellent front-rear suspension balance with responsive control, regardless of power source. Featuring slipper clutch, front & rear gear differentials, oil shocks and full ball bearings, the high durability and impact resistance allows drivers to unleash the full potential of the chassis. Brake disc wheel hubs with two different offsets (0mm, +5mm) provide compatibility with 190mm and 200mm width body styles and allows the wheelbase to be adjusted to 270mm by replacing some parts (sold separately) for compatibility with other 1/10 scale body styles. The Readyset package comes fully assembled and includes everything except charger and battery for the chassis, and batteries for the transmitter. Features: “Ultra Scale Body” replicates the fine details of the actual body of the car LED light unit (KYO97054 - not included) can be attached to the front and rear light buckets, making it even more realistic Factory-assembled Readyset package only requires 4 x AA alkaline batteries for the transmitter, and battery with charger for the chassis Full ball bearings that reduce drive loss equipped throughout the drive system Features KS202W waterproof steering servo Sealed differential and transmission deliver reliable performance, even on dusty parking lot surfaces Shaft drive full-time 4WD touring chassis Equipped with a plated dummy brake disc and a painted brake caliper to improve the sense of scale Button head hex screws throughout to simplify maintenance Motor mount mounting holes specific to pinion gear size to simplify gear ratio changes - supports from 29T to 37T Performance can be further enhanced by installing various optional parts Specifications: Length: 450mm Width: 195mm (Body width:200mm) Height: 136mm Chassis Height: 8mm (approx.) Wheelbase: 260mm Tread (F/R): 167mm Tires (F/R): 64×27.7mm Gear Ratio: 6.54:1 Weight: 1650g (approx.) R/C System: Syncro KT-231P+ Motor: G14L Includes: Completed chassis with R/C radio installed Factory assembled body complete with color scheme Syncro KT-231P+ transmitter Hexagonal wrench Spanner Needed to Complete: (4) AA batteries for transmitter 7.2-7.4V battery w/T-Style plug for chassis Charger for battery Tools This product was added to our catalog on July 19, 2022
$269.99
KYOSHO KYO34473T1, Kyosho EP Fazer Mk2 FZ02-D 2006 Subaru Impreza ReadySet w/Syncro KT-231P Radio
KYO34473T1, Kyosho EP Fazer Mk2 FZ02-D 2006 Subaru Impreza ReadySet w/Syncro KT-231P Radio Fazer Mk2 FZ02-D 2006 Subaru Impreza Ready Set Overview: The Kyosho Fazer Mk2 FZ02L 2006 Subaru Impreza was created for the pure enjoyment of RC car driving. The combination of a beautifully reproduced body with the Fazer series chassis can’t be beaten. Kyosho has taken its standard touring car chassis and given it a full model makeover that has evolved performance to a new level. A simplified design with fewer parts has improved maintenance efficiency and reduced weight while core strength and rigidity have been increased through new materials with ribbing and stiffeners on front and rear. In addition, the symmetrical chassis design synergizes excellent front-rear balance through the suspension with responsive control, regardless of the power source. Featuring a slipper clutch, front and rear gear differentials, oil shocks and full ball bearings, the high durability and impact resistance allow drivers to unleash the full potential of the chassis. Brake disc wheel hubs with two different offsets (0mm, +5mm) provide compatibility with 190mm and 200mm width body styles and allow the wheelbase to be adjusted to 270mm by replacing some parts (sold separately) for compatibility with other 1/10 scale body styles. The Readyset package comes fully assembled and includes everything except the charger and battery for the chassis, and batteries for the transmitter. Features: Officially licensed by Subaru to Kyosho Based on the GDB type Impreza nicknamed Hawkeye. Pre-painted finished body with Kyosho's original coloring with beautiful gradation and flashy colors that are conscious of the drift scene. On the side of the body, the number 60 is placed to commemorate the 60th anniversary of Kyosho. Factory-assembled Readyset package only requires (AA) alkaline batteries for the transmitter and battery with charger for the chassis! In the initial setting, the vehicle height is raised so that troubles due to gaps can be avoided. Full ball bearings that reduce drive loss equipped throughout the drive system. Sealed differential and transmission deliver reliable performance, even on dusty parking lot surfaces. Shaft drive full-time 4WD touring chassis. Equipped with a plated dummy brake disc and a painted brake caliper to improve the sense of scale. Uses Hex head button or countersunk screws within each part. Reliable tightening torque can be applied, and maintenance is possible with even fewer tools. Motor mount with holes to accommodate 29T to 37T pinion gear. Performance can be further enhanced by installing various optional parts. Chassis realizes a low center of gravity with its simple, functional design. Featuring an integrated gearbox that optimizes the torsional rigidity of the main chassis, the nylon material reduces weight while improving impact resistance. Each key component has been reinforced in this simple design without an upper deck. Reduced number and variety of screws and parts, and consolidation of frequently used screws into the same size. Most screws are flat head screws that can be removed with a 2.0mm hex wrench for easy disassembly. Handling factors such as bump steer and scrub radius are optimized on the front suspension. Simple ball-connected steering knuckle promises reliable control movement. Interchangeable on both front and rear left-right hub carriers optimize spare parts utilization and improve maintenance efficiency. Resin drift tires that have both control performance and slide performance are equipped with 5-spoke racing wheels with deep rims that are conscious of the drift scene. Specifications: Scale: 1/10 Drivetrain: 4WD Shaft driven Length: 456mm Width: 205mm Height: 140mm Wheelbase: 260mm Tread (F/R): 174mm Tires (F/R): 63.2×24.2mm Gear Ratio: 6.54:1 Weight: 1650g (approx.) Motor: G14L Includes: (1) Kyosho Fazer Mk2 FZ02-D 2006 Subaru Impreza Ready Set Electric Touring Car (1) Syncro KT-231P+ transmitter and receiver (1) Hexagonal wrench (1) Spanner (1) Drift wheels set Needed to Complete: (1) 2S (7.4V) LiPo Battery with T-Style connector (1) Compatible Charger (4) (AA) Batteries This product was added to our catalog on December 30, 2023
$269.99
MST MXS-110059, MST 1.5x7.8mm Shafts (8)
MST 1.5x7.8mm Shafts. These replacement shafts are intended for the MST RMX 2.0 S or the FFX-D. Package includes eight shafts.
$3.99
MST MXS-120001,MST 10x15mm Ball Bearing (4)
MST 10x15mm Ball Bearing. These replacement bearings are intended for the MST FXX-S, RMX 2.0 S or the TCR platform. Package includes four bearings.
$7.99
MST MXS-120002, MST 5x10mm Ball bearings (4)
MST 5x10mm Ball bearings. These replacement bearings are intended for the MST RMX 2.0S or the FXX-D. Package includes four bearings.
$8.99
MST MXS-130040, MST Ball Differential Grease
MST Ball Differential Grease. This is the diff grease used with the RMX 2.0 S ball diff.
$2.99
MST MXS-148013, MST 48P Metal Pinion Gear (13T)
MST 48P Metal Pinion Gear. This pinion gear is made from metal and designed to provide a strong finish. Available in multiple sizes, please select the size you need from the list above. Package includes one pinion gear.
$8.99
MST MXS-148015, MST 48P Metal Pinion Gear (15T)
MST 48P Metal Pinion Gear. This pinion gear is made from metal and designed to provide a strong finish. Available in multiple sizes, please select the size you need from the list above. Package includes one pinion gear.
$6.99
MST MXS-148015P, MST 48P Metal Pinion Gear (15T)
MST 48P Metal Pinion Gear. Made from durable metal, this pinion is designed to fit standard motors with a 3.17mm bore. Package includes one pinion gear.
$7.99
MST MXS-210025, MST Bevel Gear Set (40/16T)
MST Bevel Gear Set. Package includes 40 tooth rear main gear and 16 tooth bevel gear compatible with the RMX 2.0 S, RRX, FSX, FXX and XXX drift chassis.
$12.99
MST MXS-210034, MST Bevel Gear Set (36/17T)
MST Bevel Gear Set. This is the 36 tooth rear main gear and 17 tooth bevel gear used on the FXX-D chassis, but can be used as a gear tuning option on the RRX, RMX, FSX and XXX models as well.
$12.99
MST MXS-210035, MST Bevel Gear Set (40/13T)
MST Bevel Gear Set. This is the replacement 40 tooth rear main gear and 13 tooth bevel gear used on the RMX 2.0 S chassis, but can be used as a gear tuning option on the RRX, RMX, FSX, FXX and XXX drift chassis as well.
$12.99
MST MXS-210070, MST RMX 2.0 S HT Rear Lower Arm & Wheel Hub
MST RMX 2.0 S HT Rear Lower Arm & Wheel Hub. This is the replacement 4 hole rear arm and wheel hub. Package includes one arm and one wheel hub that can be used on the right or left side of the chassis.
$8.99
MST MXS-210071, MST Damper Cylinder (2)
MST Damper Cylinder. Package includes two replacement plastic shock bodies that are used in the front and rear position on the FXX-D and RMX 2.0 S series vehicles.
$7.99
MST MXS-210282, MST Rear Diffuser
This MST Rear Diffuser is an optional accessory for the RMX-D, FMX-D, FSX-D, FXX-D, XXX-D, FS-01D, XXX-RA and XXX-R models. Package includes diffuser and hardware.
$13.99
MST MXS-210491, MST 5.8x4mm Ball Connector L (4)
The MST 5.8x4mm Ball Connector L is a replacement for RRX-D, RMX-D, FMX-D, FSX-D, FXX-D and XXX-D models. Package includes four L type ball connectors.
$7.99
MST MXS-210520, MST RMX Rear Shaft Ball Differential Set (40-13)
The MST RMX Rear Shaft Ball Differential Set is an upgrade for the RMX 2.0 S, as well as the RMX-D kits equipped with the optional 4WD conversion (MXS-210452). Package includes precision machined outdrives, and the rest of the parts to build one complete ball diff with 40/13T gearing.
$40.99
MST MXS-210588R, MST Aluminum Steering Arm Mount
MXS-210588R, MST Aluminum Steering Arm Mount MST Aluminum Steering Arm Mount. This is the optional aluminum steering arm mount for the MST RMX 2.0 kit and is a direct replacement for the stock mount (MXS-230058). This aluminum material will help to stiffen up the steering assembly for increased durability and more precise steering performance. Package includes arm mount, steering mount posts and hardware. This product was added to our catalog on September 1, 2021
$18.99
MST MXS-210590R, MST RMX 2.0 Aluminum Steering Joint Plate (Red)
MST RMX 2.0 Aluminum Steering Joint Plate. This optional aluminum steering plate will add strength and improve steering precision compared to the stock plastic plate (MXS-230058). In addition to the stock mounting holes, this mount offers four additional ackermann holes for increased tuning options. Combine this with the optional Aluminum Steering Arm kit (MXS-210589) for the ultimate in steering performance. Package includes steering plate, bearings and hardware. NOTE: Stock ackermann mount holes are the middle row.
$37.99
MST MXS-210594, MST RMX 2.0 MB Rear Suspension Kit
MXS-210594, MST RMX 2.0 MB Rear Suspension Kit
$39.99
MST MXS-210616R, MST Aluminum MB Rear Suspension Kit (Red)
This is an optional MST Red Aluminum MB Rear Suspension Kit, intended for use with MST RMX 2.0 1/10 2WD Drift Car kits. These red anodized aluminum parts are stronger and longer lasting than the stock plastic version, while adding style points to the kit. The length can be adjusted to either 3mm longer or 3mm shorter than the stock part for added adjustability and customization.
$133.99
MST MXS-210642BK, MST RMX 2.0 Aluminum Rear Gearbox Set (Black)
MST RMX 2.0 S Ball Differential Outdrive Joint. These are the replacement outdrives for the RMX 2.0 S ball diff. Package includes two outdrives, t-nut and two spreader rings.
$124.99
MST MXS-210644, MST RMX 2.0 Aluminum Ball Differential Set
MST RMX 2.0 Aluminum Ball Differential Set
$49.99
MST MXS-210653, MST RMX 2.5 Aluminum Idler Gear (22T)
MST RMX 2.5 Aluminum Idler Gear (22T)
$9.99
MST MXS-230059, MST RMX 2.0 S Ball Differential Outdrive Joint
MST RMX 2.0 S Ball Differential Outdrive Joint. These are the replacement outdrives for the RMX 2.0 S ball diff. Package includes two outdrives, t-nut and two spreader rings.
$12.99
MST MXS-230061-1, MST RMX 2.0 S Rear Gear Box Set
MST RMX 2.0 S Rear Gear Box Set. Package includes replacement transmission case halves, bearing holder, and spur gear mount.
$18.99
You have seen 48 out of 109 products