The Aikon flight controller is a new generation flight controller and ESC combination specifically designed for cinewhoops and other high-current applications. We've packed all the greatest features into one seamless flight experience.
Check out our other AIO flight controllers and the rest of our Aikon gear!
Features
216mhz F7 processor
Independent FC and ESC PCBs for low noise
5 Software invertible hardware UARTS
Onboard OSD and BlackBox
Software-controlled VTX power switch (assigned to USER1 mode by default)
Connectors for DJI-HD and RC link
LED and buzzer outputs (LED pad doubles as PPM)
On-board high overhead voltage regulators rated up to 6S (50v peak to handle voltage spikes)
10v 1.5A voltage regulator for DJI HD system
3.3mm high current MOSFETs.
Specifications
Battery: 3-6S
Mounting Holes: 25.5x25.5mm
FC Firmware: Betaflight AIKONF7 Target
MCU: STM32F722
IMU: MPU6000
Barometer: DSP310
Blackbox: SPI 16MB
ESC Firmware: BLHeli_32
Constant Current: 45A
Burst Current: 55A
Current Sensor Scale: 200
Weight: 14.5g
Includes
1x Aikon F7 Mini 25x25 AIO Flight Controller w/ 45A 32bit ESC
This FC pairs seamlessly with any Aikon ESC. The F7 MCU will allow you to dial in your tune the way you want it and the DJI plug and play means it's ready to go with the Air Unit or Vista.
Check out all our 20x20 FCs, our DJI compatible gear section, and all our Aikon gear!
Features
216mhz F7 processor
5 Software invertable hardware UARTS
Onboard OSD and blackbox
Software controlled VTX power switch
LED outputs
Quick connection cable for 4-in-1 ESCs
On-board high overhead voltage regulators up to 6S (50v peak for voltage spikes)
10V/1.5A regulator for DJI HD system
DJI Quick Connect Port
Specifications
Input Voltage: 2-6s
Mount Hole: 20x20mm
Betaflight Target: AIKONF7
MCU: STM32F722RET6
IMU: BMI270
Blackbox SPI: 16MB
Weight: 8g
Includes
1x Aikon F7 Mini V3 HD 20x20 Flight Controller for DJI
Wiring Diagram
The G4 features Betaflight compatibility and is the first of its kind. It contains 4 35A AM32 ESCs, 6S max and the QF32MTF4AK8U7 on the AIO board, creating a more compact design. Two voltage regulators – a 5V and 10V, both rated for 2.5A – are included. The 10V one can power the VTX & DJI O3 Air Unit, while the 5V one can power the LEDs, peripherals, etc. The STM32G47X MCU, ICM-42688p gyro, 16MB Data Flash, DSP310 baro, 16 RGB LEDs, and plug solutions for digital video complete the package.
A new feature is the ultra-hydrophobic nano waterproof coating. This coating allows air to pass through while avoiding water, giving extra protection from moisture and other elements.
Important note: When trying to get the HD OSD working, it's required that both ground pins out of the DJI port are not soldered to the VTX.
Check out our other AIO flight controllers, as well as the rest of our Airbot selection!
Features
Superhydrophobic Nano Waterproof Coating
Onboard 16 RGB LEDs can be programmed
ESC has a F4 MCU, runs AM32 firmware, capable of 6S and is rated at 35Amps
10V BEC for DJI O3 Air Unit
Specifications
MCU: STM32G473, 512KB Flash
BEC: 5V 2.5A + 10V 2.5A
Blackbox: 128Mbit, 16MB
Gyro: ICM-42688
Barometer: DSP310
ESC: F4 MCU, run AM32 firmware, 6S 35Amps
OSD: AT7456
4x Uarts
1x 12C
Weight:10.4g
Mounting pattern：25.5x25.5mm
Connector Pinout:
SDA, SCL, DN, DP, GND, 5V, L-RX1, L-TX1 is for External USB/GPS Connector
TX2, GND, RX1, TX1, GND, 10V is for VTX Connector
Wiring Diagram
- Information was referenced from a review of the Airbot Fenix G4 AIO board brought to you by VitroidFPV.
Revised version now includes a power switch and additional solder pads.The Analog FPV FatShark Module Adapter V2 for DJI Digital FPV Goggles fits so well you can use a fat shark or various third-party fat shark style analog video receivers modules! It transfers video and audio signals to the high-quality screen of DJI FPV goggles for viewing or recording. This compact and lightweight adapter is easy to install and won't void your warranty! Check out all our DJI compatible frames, electronics & accessories and our FPV receiver modules & antennas collection!Specifications
Input Voltage: 2S-4S (DC5.5x2.1mm)
Internal Voltage: 5V 3A (with pad output)
Output Voltage: 2S-4S (DC 5.5x2.1mm)
Signal Input: Standard Fat Shark Receiver Port
Including third-party receivers: Realacc, Furious, etc.
Signal output: standard audio / video
Power Switch
Dimension: 48x28x12mm
Weight: 10g (without extension cable)
Includes
1x Analog FPV Adapter for DJI Goggles
1x Adapter mounting board and screws
1x Audio and video cable
1x Power cable
Wiring Diagram
V3 now includes a voltage display, power switch and additional solder pads.This analog fat shark module adapter fits on the side of your DJI Digital FPV Goggles so you can use a fat shark or various third-party fat shark style analog video receivers modules! It transfers video and audio signals to the high-quality screen of DJI FPV goggles for viewing or recording. This compact and lightweight adapter is easy to install and won't void your warranty! We also have the V2 Adapter if you don't need the voltage display. Seen below installed in the Aluminum Case we carry specifically for this device:Check out all our DJI compatible frames, electronics & accessories and our FPV receiver modules & antennas collection!
Specifications
Input Voltage: 2S-4S (DC5.5x2.1mm)
Internal Voltage: 5V 3A (with pad output)
Output Voltage: 2S-4S (DC 5.5x2.1mm)
Signal Input: Standard Fat Shark Receiver Port
Including third-party receivers: Realacc, Furious, etc.
Signal output: standard audio / video
Dimension: 55x28x12mm
Weight: 13g (without extension cable)
Includes
1x Analog FPV Adapter V3 for DJI Goggles
1x Adapter mounting board and screws
1x Audio and video cable
1x Power cable
1x Allen Key
Wiring Diagram
All Armattan warranty claims must be handled directly through Armattan. Please follow this link with instructions on how to file for a warranty claim. https://armattanquads.com/warranty-claims/
After many designs and prototypes, the Armattan Beaver Frame 5" Quadcopter Frame Kit is here! The Armattan Beaver features a strong carbon frame with thicker arms than previous versions which makes it the strongest to date. This frame focuses on noise reduction, easy maintenance, and versatility for use with a variety of electronics. With a weight of 126g, this frame is lighter than previous Armattan frames.
Check out our other 5" frames, as well as the rest of our Armattan selection!
Features
Ease of maintenance: Only one bolt needs to be removed to replace an arm at the field
Well-balanced frame (strength and weight distribution)
Great price point for a high-end, freestyle frame
Thicker arms than any other previous frame
Light and small camera cage
Easy to tune for newcomers
Strong, stiff and light frame
Crash-protection provisions
Good-looking frame
Lifetime warranty
Noise reduction
Versatile
Specifications
Stack Mounting: Two 30.5x30.5mm stacks(center and rear) + Two 20x20mm stacks (4 possible positions)
FPV Camera Mount: 20mm(DJI) or 19mm Micro cam
Motor Mount Pattern: 16x16 or 16x19 or 19x19mm
Warrantied Parts: All CF and alumi frame parts
Main Plate Thickness: 2.5mm
Frame Shape: Compressed X
Frame Weight: 126 grams
Max Stack Height: 25mm
Motor to Motor: 235mm
Arm Thickness: 5mm
Includes
Carbon Fiber
1x 2mm bottom plate
1x 2.5mm main plate
4x 5mm arms 5 inch
1x 2mm top plate
1x 4mm arm core
Hardware
4x M3 25mm profiled alumi standoff
5x M3 20mm button head iron bolt
6x Aluminum cone spacer orange
5x M3 6mm nylon standoff F/F
20x M3 6mm 12.9 grade bolt
5x M3 10mm 12.9 grade bolt
5x M2 2.5mm cup head bolts
2x M3 20mm alumi standoff
9x M3 12mm cup head bolt
3x M3 16mm cup head bolt
5x M2 18mm cup head bolt
5x M2 nylon washer
14x M3 nylon nuts
5x M2 nylock
Metal
1x Right aluminum cam brace orange
1x Left aluminum cam brace orange
2x Aluminum tail posts orange
2x Aluminum cam saver black
Foam
4x Dog bone landing pads
1x Air unit foam
1x Center foam
1x Lite grip
Accessories
1x 25cm clear heat-shrink 20mm wide
4x Motor wire extension PCB
1x Universal antenna mount
2x White lipo strap
All Armattan warranty claims must be handled directly through Armattan. Please follow this link with instructions on how to file for a warranty claim. https://armattanquads.com/warranty-claims/
Introducing the Armattan Bobcat. 4 inch models are making a come back on the FPV scene. This frame supports a Vista, DJI air unit and DJI O3 Air Unit. This frame can become a compressed X frame or a True X frame depending on how you install the arms. A one of kind frame, brought you by the master frame makers at Armattan.
Check out the rest of our 4" frames, as well as the rest of our Armattan selection!
Features
Dual arms configurations
Front and Rear stack mounting
Re-designed camera cage making it lighter and stronger
Specifications
Frame Weight: 57 grams
Motor to Motor: 182mm (Compressed X)
Motor to Motor: 200mm (True X)
Frame Shape: True X or Compressed X (Modular)
Main Plate Thickness: 2.5mm
Arm Thickness: 3mm
Motor Mount Pattern: 12x12 or 9x9mm
Stack Mounting: Dual M3 20x20mm & M2 16x16mm
FPV Camera Mount: 20mm(DJI) or 19mm Micro cam
Max Stack Height: 20mm
Includes
1x Armattan Bobcat HD 4" Frame Kit
2x Cam Brace
2x Anchor
2x Tail Post
4x Arms 4 inch
1x Center Plate
1x Top Plate
2x Camera Mounting Plate
2x Tie Plate
1x M3 12mm cage standoff
2x M2 20mm cage standoff
5x M2 8mm cup-head bolt
3x M3 12mm button-head bolt (12.9 grade)
3x M3 8mm button head bolt (12.9 grade)
10x M2 6mm cup-head bolt
12x M3 9mm button head bolt
15x M3 sunk nuts
5x M3 20mm bolts
10x M3 nylon nuts
5x M3 6mm nylon standoffs
5x M2 18mm cup-head bolt
5x M2 aluminum nylocks
5x M2 nylon washer
5x M2 metal washer
3x M3 8mm cup-head bolt CW
1x Oomph spacer
2x Lipo strap
1x Top Lite Grip (gel & adhesive foam hybrid pad)
1x Air unit double sided adhesive foam bits
2x Dog-bone landing pads (cuts into 6 pieces, two center pieces can be used as spares)
1x Molded rubber antenna holder
All Armattan warranty claims must be handled directly through Armattan. Please follow this link with instructions on how to file for a warranty claim. https://armattanquads.com/warranty-claims/
The Armattan Tadpole HD is basically the same as the original Tadpole except it has additional provisions and design implementation allowing it to be built using analog or digital gear. A bit like a Tadpole V2 in a way. All in all, this is a revamped version of the ever-popular Armattan Tadpole.
Check out our other 3" frames, as well as the rest of our Armattan selection!
Specifications
Wheelbase: 137mm
Frame Style: Compressed X
Main Plate Thickness: 2.5mm
Top Plate Thickness: 2mm
Stack Size: 16x16mm, 20x20mm, 25x25mm
Stack Height: 18mm
Motor Mount: 9mm Φ
Camera Mount: Micro
Weight: 26g
Includes
1x Armattan Tadpole HD 3" Frame for DJI
All batteries must be shipped by a ground shipping method.
4S Lithium-Ion battery for the DJI FPV Goggles. Connect the XT60 to a DC power cable and connect the DJI FPV Goggles to the battery.
Check out the rest of our Auline products, DJI FPV System Parts & Accessories, and our whole battery collection!
Features
XT60 Connector
Made specifically to power DJI Goggles
Long lasting
Protective board
Specifications
Capacity: 2600mAh
Voltage: 14.8V
Connector: XT60
C-Rate: 1C
Weight: 202.4g
Includes
1x Au line 14.8V 4S 18650 2600mAh 1C Li-Ion Battery w/ Built-In Protective Board - XT60
Axis Flying has released a 2.5" X8 cinewhoop frame. Featuring a true X8 design for more thrust on a smaller platform, this 2.5" is ready for any kind of HD cam on top and is ready to shred while doing so!!!!Check out all our DJI-compatible frames, electronics, and accessories, and all our Axis Flying Products!
Features
Includes motor LEDs
Durable carbon
Durable and lightweight ducts
Specifications
Wheelbase: 125mm
Top plate: 2mm
Bottom plate: 2mm
Arm: 3.0mm
FC mounting holes: 20mm x 20mm / 30.5mm x 30.5mm
VTX mounting holes: 20mm x 20mm / 30.5mm x 30.5mm
Motor mounting holes: 9mm x 9mm
Camera installation space: 19-20mm
Suitable propeller size: 2.5″propeller
Weight: 105g (without TPU)
Includes
1x Axis Flying AirForce PRO X8 2.5″ Cinewhoop Frame Kit
2x Battery straps
1x Battery Silicone Pads
1x Set of screws
The latest from AxisFlying, the Argus F7 is a powerhouse of a chip. It comes in two versions, regular and PRO which has a CNC heat dissipation aluminum cover. It has a high-performance F722 chip, onboard barometer, OSD and Black Box. And it can support up to 8 motors! This chip comes packed with power. Pair it with the Argus 65A ESC for ease of installation; a convenient plug-and-play feature. And it supports the new DJI O3 Air Unit! AxisFlying has got you covered!
Check out all our 30x30 Flight Controllers, and all our Axis Flying Products!
Features
High-quality and large-size MOSFETs are selected, with low internal resistance and low heat generation.
No welding, more peace of mind. With this FC, HD Air unit, analog camera, GPS, and other common peripherals all support direct plug-in
Integrated dual BEC, support DJI O3 Air Unit direct connection
The FC supports up to 8 motor outputs, easily build your X8 drone
Quickly check the working status of the FC by turning on and off the corresponding status indicator light
Specifications
MCU: STM32F722RET6
Gyro: BMI270
Barometer: Yes
OSD: Yes
BEC: 9V/2A, 5V/2A
UART Ports: 6
Black Box: 16MB onboard
Number of supported motors: 8
Firmware Name: AXISFLYINGF7
Input Voltage: 3-6S LiPo (12-50V Max)
Installation Holes: 30.5x30.5mm M3
Includes
1x AxisFlying Argus F7 3-6S 30x30 Flight Controller
1x Assorted Connector wires
The latest from AxisFlying, the Argus F7 is a powerhouse of a chip. It comes in two versions, regular and PRO which has a CNC heat dissipation aluminum cover. It has a high-performance F722 chip, an onboard barometer, OSD and Black Box. And it can support up to 8 motors! This chip comes packed with power. Pair it with the Argus 65A ESC for ease of installation; a convenient plug-and-play feature. And it supports the new DJI O3 Air Unit! AxisFlying has got you covered!
Check out all our 30x30 Flight Controllers, and all our Axis Flying Products!
Features
High-quality and large-size MOSFETs are selected, with low internal resistance and low heat generation.
No welding, more peace of mind. With this FC, HD Air unit, analog camera, GPS, and other common peripherals all support direct plug-in
Integrated dual BEC, support DJI O3 Air Unit direct connection
The FC supports up to 8 motor outputs, easily build your X8 drone
Quickly check the working status of the FC by turning on and off the corresponding status indicator light
Specifications
MCU: STM32F722RET6
Gyro: BMI270
Barometer: Yes
OSD: Yes
BEC: 9V/2A, 5V/2A
UART Ports: 6
Black Box: 16MB onboard
Number of supported motors: 8
Firmware Name: AXISFLYINGF7
Input Voltage: 3-6S LiPo (12-50V Max)
Installation Holes: 30.5x30.5mm M3
Includes
1x AxisFlying Argus F7 3-6S 30x30 Flight Controller
1x Assorted Connector wires
Experience the efficient and reliable AIO solution of the AxisFlying Argus F722 F7 for your Whoop/Toothpick builds, complete with 40A 8Bit 4in1 ESC and pink aluminum shell. CNC heat sink on both sides ensures better cooling and longer service life.
Browse the rest of our Whoop AIO Boards and all our Axis Flying Products!
Feature
Every AIO goes through 800 full-throttle takeoff and landing tests before leaving the factory. High-quality circuit technology and aluminum shell casing will ensure their service life.
Stylish CNC heat sink on both sides. Better cooling and increased lifespan.
The big concern of every pilot - desyncs - will be solved by the Argus F7 AIO.
Perfectly match with 20/21 motors.
PNP HD VTX interface
Specifications
FC target: AXIS ARGUS F7 AIO
DJI O3 dedicated plug: Supported
Barometer: Supported
Beeper: Supported
Sized: 36x36x7.2mm
MCU: STM32F722RET6
Gyro: BMI270
Continuous Current: 40A
Peak Current: 50A
Uart: 5
OSD: Supported
LED: Supported
Input Voltage: 4-6S
Mounting: 25.5x25.5mm/26.5x26.5mm M3
Includes
1x Axisflying Argus F722 F7 Whoop/Toothpick AIO Flight Controller w/ 40A 8Bit 4in1 ESC & Pink Aluminum Shell
Axisflying’s new CineON 30 replacement ducts.
Check out all our DJI-compatible frames, electronics, and accessories and all our Axis Flying Products!
Features
Spare ducts
Lightweight and Durable
Two color options
Includes
2x Dual 3" Prop Guards
The AxisFlying CineON C30 V2 Cinewhoop 3" Micro Frame Kit is a powerful and lightweight piece of engineering, built for maximum durability and performance. It has a unique 4-screw blade guard swap for easy maintenance, and supports 19x19mm camera mounting for DJI O3 cameras. Featuring CNC aluminum camera side plates, and a 3D printed GPS mount on the tail, this kit is an all-in-one solution for advanced aerial photography.
Choose the color of your prop guards between blue-green clear and grey clear!
Check out our other 3" frames and all our Axis Flying Products!
Features
Fully upgraded redesign and new appearance
Camera side plates have been upgraded to CNC aluminum parts
Compatible with DJI O3 Cameras
Supports cameras with a 19x19mm mounting
The tail has been equipped with a 3D printed GPS mount
Specifications
Wheelbase: 138mm
Top plate: 3.2mm
Bottom plate: 2mm
Arm: 3.2mm
FC mounting holes: 25.5mm x 25.5mm M2 / 20mm x 20mm M2
VTX mounting holes: 25.5mm x 25.5mm / 20mm x 20mm
Motor mounting holes: 9mm x 9mm / 12mm x 12mm
Camera installation space: 14-20mm
Suitable propeller size: 3″propeller
Weight: 127g (without TPU)
Includes
1x AxisFlying CineON C30 V2 Cinewhoop 3" Micro Frame Kit
1x Battery Ant-Slip Pad
1x 3D Printed Parts Set
1x Hardware Set
1x Main Plate
2x LiPo Strap
1x Top Plate
Axisflying’s new CineON 30 replacement ducts.
Check out all our DJI-compatible frames, electronics, and accessories and all our Axis Flying Products!
Features
Spare ducts
Lightweight and Durable
Two color options
Includes
2x Dual 3.5" Prop Guards
The Axisflying Kolas 6 is a 6" long-range FPV frame with up to 15 minutes of flight time. Axisflying has adopted an innovative folding design with the Kolas 6, allowing for easier storage and transport! This unique frame kit also includes all 3D printed parts.
Check out all our DJI-compatible frames, electronics, and accessories and all our Axis Flying Products!
Features
XT60 plug on the left side of the frame for flight safety
25MM top to bottom distance for Caddx Vista
Open right side design for quick tuning
20MM/25MM/26.5MM Mounting Holes
Independent receiver compartment
High-strength T700 carbon plate
Foldable drone for easy storage
Ability to carry GoPro Camera
16x16 motor mounting holes
Underslung navigation light
15 Minute flight time
6" Foldable arms
Specifications
Wheelbase: 245mm
Top plate: 2.5mm
Bottom plate: 32.5mm
Arm: 7.0mm
FC mounting holes: 25.5mm x 25.5mm M2 / 20mm x 20mm M3
VTX mounting holes: 25.5mm x 25.5mm / 20mm x 20mm
Motor mounting holes: 16mm x 16mm
Camera installation space: 19-20mm
Suitable propeller size: 6″propeller
Weight: 138g (without TPU)
Includes
4x Axisflying Kolas 6 Foldable 6" Arms
1x Battery Ant-Slip Pad
1x 3D Printed Parts Set
2x Camera Side Plates
1x Hardware Set
1x Main Plate
2x LiPo Strap
1x Top Plate
Axis Flying has released a 6" Dead-cat version of their Manta freestyle frame. Featuring easy swapping arms and an all aluminum camera cage, This 6" is ready for any kind of mountain surfing or abusive freestyle flying you may get yourself into!!!!
This frame has been specially designed around fitting the O3 Air Unit.
The DC structure better suitable for the O3 internal recording, as there are no propeller is visible during flight. While the X structure is more suitable for freestyle, though you are gonna see propeller is slightly visible during O3 internal recording.
Check out our other DJI O3 Compatible Quads and DJI compatible frames, electronics and accessories and all our Axis Flying Products!
Features
Aluminum alloy arm plates to keep your arms rigid
Easy swap arm function
No props in view Dead-cat style
Full set of TPU accessories
Bottom LED and Beeper for night flying.
GPS is placed above the antenna for less interference.
Double strap ties for secure battery installation.
No props interference, unobstructed flight field of view
Specifications
Wheelbase: 265mm
Structure: DC Type
Top plate: 2.5mm
Bottom plate: 2.5mm
Arm width: 5.0mm
FC mounting holes: 20mm x 20mm / 30.5mm x 30.5mm
VTX mounting holes: 20mm x 20mm / 30.5mm x 30.5mm
Motor mounting holes: 16mm x 16mm / 19mm x 19mm
Camera installation space: 19-20mm
Suitable propeller size: 6.1″propeller
Dimension: 262mm x 159mm x 25mm
Weight: 199.0g (without TPU)
Includes
1 x AxisFlying Manta HD O3 Mid-Range Deadcat 6" Freestyle Frame Kit
1 x Battery strap 250mm
1 x Battery strap 220mm
1 x Battery Silicone Pads
1 x Set of 3D printings
2 x Action camera mount holder
1 x Set of screws
This frame kit only comes with a TPU front bumper. Product images are a reference.
The AxisFlying Manta 5-inch Freestyle Frame is a premium True X frame that is as beautiful as it is solid. The Manta has easily swappable arms with 7075 aluminum standoffs, aluminum camera plates, and an aluminum base that securely holds the arms in place to keep them from slipping. It is built from smooth T700 carbon fiber with 5mm fast swap arms. The frame is compatible with either 20x20 stacks or 30x30 stacks and is perfect for the Axisflying Plug and Play Stack 50A+F7 iSTACK. You can't go wrong with this quality frame.
Check out all our DJI-compatible frames, electronics, and accessories and all our Axis Flying Products!
Features
Aluminum alloy arm plates to keep your arms rigid
Easy swap arm function
True X Frame
Specifications
Wheelbase: 126mm
Top plate: 2.5mm
Bottom plate: 2.5mm
Arm: 5.0mm
FC mounting holes:20mm x 20mm / 30.5mm x 30.5mm
VTX mounting holes: 20mm x 20mm / 30.5mm x 30.5mm
Motor mounting holes: 16mm x 16mm
Camera installation space: 20mm
Suitable propeller size: 5″propeller
Dimension: 168.5mm x 168.5mm x 25mm
Weight: 126.0g (without TPU)
Includes
1 x Axis Flying MANTA 5inch True X freestyle Frame Kit
2 x Battery strap
1 x Battery Silicone Pads
1 x 3D printed bumper
1 x Set of screws
New V2 comes with a tactile power button, 6S support and a cable management kit! The plug and play Digidapter from British Drone Industries is the cleanest way to add analog FPV capabilities to your DJI Goggles. The injection molded face plate keeps your goggles looking sharp, and the included cables mean soldering is purely optional.
Check out all our FPV receiver modules and our DJI compatible gear!
Features
Short delay tactile power button for analog module
Compatible with existing modules: The Digidapter is compatible with existing analog modules. Featuring a standard 9 pin header for use with the TBS Fusion, Foxeer Wildfire, Rapid Fire, True D-X, Eachine Pro58, and more..
Plug & Play No Solder Solution: Installation takes less than a minute, and mounts quickly and easily to the front of your DJI Digital FPV Goggles. Including optional solder points for a cable free solution.
New cable management set included!
Specifications
Maximum Input Voltage: 28 Volts DC
Minimum Input Voltage: 7.4 Volts DC
Nominal Output Voltage: 5 Volts DC
Maximum Module Supply Current: 1 Amp
Rated Continuous Power: 5 Watts
Ports:
5.5mm x 2.1mm DC In 7.4v-26v (2s-6s)
4 pole 3.5mm video/audio out
9 pin RF module receiver header
Cables:
5.5mm x 2.1mm Male to Dual 5.5mm x 2.1mm Female DC Jack Splitter
4 Pole Gold Plated 3.5mm Male to 3.5mm Male Video Cable
Material/Color: Matte Black, Injection Molded, Acrylonitrile Butadiene Styrene
Dimensions: 158x74x40mm (6.25x3x1.6 inches)
Weight: 34g
Includes
1x Digidapter V2 faceplate
1x Analog video cable
1x Analog video/audio splitter for audio out
1x Dual DC/DC male to single DC female split cable
1x Allen key
2x 12mm cap head bolts
1x Cable strain relief clip
2x Cable clips
The BDI Luxe Goggle Bag is designed specifically to hold your DJI FPV goggles without removing the BDI analog adapter! This bag also features an ultra soft 15mm synthetic fur interior and rugged nylon exterior to give your FPV goggles the ultimate protection. The robust weatherproof zip pocket provides a safe place for all of your cables and accessories along with spacious storage for multiple battery packs. A generous interior enables storage of a fully loaded set of FPV goggles complete with antenna, with a dual pull cord opening you can be packed and ready to go in moments.
Make sure to check out our other DJI compatible accessories and all of our BDI products!
Specifications
Dimensions: 280x230mm
Includes
1x BDI Luxe Goggle Bag for DJI FPV Goggles
2x Microfiber Cloths
Premium FPV Goggle Protection, BDI Luxe Bag Mini features an ultra-soft 15mm synthetic fur interior and rugged nylon exterior to give your FPV goggles the ultimate protection.A generous interior is sized to fit the latest generation of digital goggles and accessories including;DJI Goggles 2DJI ControllerWalksnail/Caddx Avatar GogglesTBS Tango 2 ControllerThe robust weatherproof zip pocket provides a safe place for all of your cables and accessories along with spacious storage for multiple battery packs.With a dual pull cord opening, you can be packed and ready to go in moments.
Make sure to check out our other DJI compatible accessories and all of our BDI products!
Includes
1x BDI Luxe MINI Goggle Bag for DJI Goggles 2
The ND filters are specifically designed for the Pavo Pico Brushless Whoop Quadcopter. Meanwhile, the DJI O3 Air Unit ND Filters are tailored for the DJI O3 Air Unit and are capable of reducing the amount of light that enters the camera lens. With this feature, you can achieve slower shutter speeds or wider apertures when flying.
These lightweight filters are crafted from high-quality optical class ensuring optimal image clarity and are too easy to install on the build.
ND4 Filter: Ideal for dark, cloudy daysND8 Filter: Perfect for cloudy days or early morning/late afternoon sunlightND16 Filter: Suitable for use on bright, sunny daysND32 Filter: Designed for exceptionally bright conditions, such as snow or water reflectionsCPL Filter: Enhances color saturation and contrast by reducing glare from reflective surfacesClear UV Filter: Protects your camera lens from dust, dirt, and scratches
Check out other DJI O3 Products!
Check out the rest of our replacement cam parts & accessories, and all our BetaFPV gear!
Features
DJI O3 filters are easy to install and protect your camera lens from dust, sand, and debris. They ensure uninterrupted high-quality footage during flights and extend the life of your equipment. Customized filters for your drone can enhance your footage and equipment protection.
ND filters reduce sunlight brightness, lower camera shutter speed to avoid overexposure, prevent distortion in high-speed motion blur shots and improve drone footage quality.
UV filters effectively minimize the blue tone caused by ultraviolet rays in outdoor photography, resulting in clearer, more saturated, and more realistic images. They also protect the camera lens from dirt, sand, and scratches.
CPL filters reduce light and mirror reflection, preventing overexposure and white reflections. They improve clarity and brightness, especially over water or reflective surfaces, resulting in a more detailed image with reduced glare.
Installation Methods
The filter supports two installation methods. To install the filter, align it with the lens position and clip it into the frame horizontally or vertically. To remove it, grip the lens mount with your thumb and pull it out.
Horizontal installation of the UV filter is more suitable for shooting ground or scenery as it effectively reduces reflections and scattering, avoiding excessive refraction of light that may affect image quality. It also provides added protection to the camera lens surface, reducing the risk of damage. Vertical installation of the UV filter is best for shooting reflective surfaces such as water or glass, as it better reduces reflections and prevents them from interfering with the shot.
Specification
Item: UV Filter / ND8 Filter / ND16 Filter / ND32 Filter / CPL Filter
Weight: 0.74g
Adapt Camera: DJI O3 Camera
Includes
1x BetaFPV DJI O3 Air Unit Camera Filters - Choose Your ND
The BetaFPV V1 F4 2-3S AIO is the perfect choice for modern Whoop/Toothpick builds. Featuring an F4 AIO Flight Controller and 20A 4-in-1 ESC with ELRS serial, this setup guarantees smooth, consistent performance. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option.
Note: If you use the F4 2-3S 20A AIO FC V1, the serial port of the SBUS receiver is UART5Check out all our whoop flight controllers, and all our BetaFPV gear!
Features
Designed for HD VTX, it features a dual 9V@2A for DJI O3 and 5V@3A for external device BEC solution to prevent screen blackout on the DJI O3 due to low voltage during throttle increase.
It includes a new DJI O3 6-pin PMU for easy installation without soldering, reducing assembly complexity. Newbie friendly.
The power range of 2-3S provides increased thrust and improved control with a 20A ESC featuring a single NMOS for continuous current capability.
The upgraded onboard receiver allows selective power cutoff for saving power and offers additional UART TX3 and RX3 ports for connecting the external device.
The redesigned solder pad layout ensures larger, more secure pads for easy and reliable soldering, while the relocated USB port at the rear facilitates computer tuning.
It features an STM32F405RGT6 chip, Integrate Serial ELRS 2.4G receiver, 16M black box, barometer, current meter, reserve 3 complete serial ports and a standard SBUS, support GPS, HD VTX, external receiver, and other equipment.
F4 2-3S 20A AIO FC V1 also has extended the USB port to the end for easier parameter adjustment and wiring. And a new DJI O3 6-pin PMU has been added for convenient installation and maintenance.FAQPower cutoff: Removing the chip bead disconnects the power supply, and to reuse the onboard ELRS receiver, soldering the solder pads together restores power.UART3 release: Removing two resistors on the solder pads releases UART3. The left side is TX3, and the right side is RX3. To reconnect, solder the solder pads together when reusing the onboard ELRS receiver.Voltage Switch: The HD VTX connector defaults to 9V. The chip bead is soldered between the 9V pad and the middle pad. To use WalkSnail Avatar HD mini 1s and Lite, please ensure the power supply voltage is 5V. Remove the chip bead first from the 9V pad and solder it between the middle pad and the 5V pad. Alternatively, you can use solder instead the chip bead to switch between the 5V and 9V pads.Motor choice: Avoid selecting motors with excessively high KV ratings, as motors above 20,000KV are prone to burn.Betaflight Firmware and CLIFC firmware: Betaflight_4.4.1_BETAFVF405Download the firmware and CLI dump fileReference link:https://github.com/betaflight/betaflight/releases/tag/4.4.1ESC FirmwareWith BB51 ESC solution, F4 2-3S 20A AIO FC V1 is based on BLHeliSuite16714903 with Bluejay ESC firmware, it supports bidirectional D-shot and RPM filtering in Betaflight, offers 24KHz, 48KHz, and 96KHz fixed PWM frequency for options, and custom start-up melodies. F4 2-3S 20A AIO FC V1 default factory setting is 48KHz and it doesn’t recommend upgrading the 96KHz, or it might cause an error in the motor idle setting, not spinning when disarmed.DO NOT flash the firmware with a shorter interval, otherwise, there will be a certain chance of stalling and burning the flight controller.ESC-Configurator: https://preview.esc-configurator.com/Download BLHeliSuite16714903Download the Bluejay ESC firmware. Please choose C_X_70.HEXConnecting External DevicesPlease note that the board reserves two serial ports and a standard SBUS port, which is available for the external CRSF protocol receiver or GPS module, and SBUS protocol receiver. You can refer to the below picture.
Specifications
Weight: 5.58g (without motor connectors and power cable), 5.92g (with motor connectors)
Mounting Hole Size: 26mm x 26mm
CPU*: STM32F405RGT6 (168MHz)
Six-Axis: ICM42688P (SPI connection)
RX: Serial ELRS 2.4G Receiver
RX firmware version: BETAFPV AIO 2400 RX ELRS V2.5.2
Antenna: Enameled wire
Blackbox Memory: 16MB
Sensor: Barometer(BMP280), Voltage&Current
5V BEC*: 5V 3A@8V supply
9V BEC*: 9V 2A@8V supply
USB Port: SH1.0 4-Pin
Built-in ESC with 20A continuous and peak 25A current
ESC input voltage: 2-3S
FC firmfware version: Betaflight_4.4.1_BETAFPVF405
ESC firmware: C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware
Signal support: D-shot300, D-shot600
Includes
1x BetaFPV V1 F4 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ELRS Serial
Wiring Diagram
F722 2-6S AIO 35A FC is a very reliable FC that is made to meet your advanced FPV needs. Comes with an F722 chip and a BLHeli_32 ESC, this board provides a better performance capability and higher calculation speed, which brings pilots a more stable and smoother flight. What's more, F722 AIO FC has specially added a 6-pin connector for DJI Digital VTX, just plug & play, less solder work needed, super easy to install. It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery.
Check out all our whoop flight controllers, and all our BetaFPV gear!
A very in-depth video on the BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller.
Features
Built-in STM32F722RET6 CPU, F722 FC is more powerful than F4. It features a fast processing speed and stable performance, providing reliable and smooth flight for 4"-5" drones.
F722 AIO 35A FC has specially added a 6-pin connector for HD Digital VTX, just plug & play, less solder work needed, perfect for the pilots who enjoy the HD Digital VTX system.
6 full UARTs are available on this board. With plenty of UARTS, Pilots could have more options for external parts like VTX, GPS, Receiver, and other components.
It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery, and gives the drone a more robust flight performance.
With the 6S battery and this F722 35A AIO FC, the drone will break through the limit of the power of the toothpick drone, exploring more possibilities in 4-5'' drones.
The new BLHeli_32 ESC version is built-in a 16MB flash memory chip dedicated to Blackbox logging, which is an extremely powerful tool for tuning and troubleshooting an FPV drone. It has a faster processing speed and up to 128k PWM frequency, providing a more stable and smoother flight for pilots.
V2 with BLHeli_32 ESC
V1 with BLHeli_S ESC
PWM Frequency
24k-128k
24k-96k
ESC Firmware
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
Blackbox
16MB
Not included
Weight
9.00g
7.06g
Board Thickness
1.6mm
1.4mm
BLHeli_32 ESC Firmware
The F722 35A AIO FC has two boards with different ESC versions for choice. The V2 board uses AT32F421G8U7 MCU, a 32-bit ESC chip, with BLHeli_32 ESC firmware. This firmware supports up to 128k PWM frequency, featuring faster processing speed and unlocking more functions for the flight.
BLHeli_32 ESC
BLHeli_S ESC
MCU
AT32F421G8U7
EFM8BB21F16G-C
Firmware Version
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
PWM Frequency
24k-128k
24k-96k
Bidirectional DSHOT
Support
Support
Signal Support
PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Know More About ICM42688 Gyro
The F722 FC ICM42688 version has the same solder pad and layout as BMI270 except for the gyro chip. Besides, you can also find the difference in Betaflight settings.
The ICM42688 gyro supports 8.00 kHz gyro update frequency compared with the BMI270 gyro which supports 3.20 kHz. When using a 6S battery, the ICM42688 gyro has a good performance.
The degree between ICM42688 and BMI270 gyro is different. When configuring F722 FC ICM42688 version, the gyro degree should be set to CW270°.
Diagram for F722 35A AIO FC
The below picture is the top front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
The below picture is the bottom front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
There are 2 LEDs on the bottom of the board to indicate the status, including the FC LED (Blue) and FC Power LED (Red). The LED status for V1 and V2 boards are the same.
LED
Status
Description
FC LED (Blue)
Solid
Armed
FC LED (Blue)
Extinguished
Disarmed
Power LED (Red)
Solid
Power on
How to Connect the External RX&VTX
To connect the external RX&VTX, please refer to the below diagram. F722 35A AIO V1 and V2 boards have the same soldering pad and connecting ports.
Specifications
Flight Controller
Item: F722 35A AIO Brushless Flight Controller
Weight: 9.00g (BLHeli_32)
CPU: STM32F722RET6
Six-Axis: ICM42688
Mounting hole size: 26mmx26mm
Firmware version: betaflight_4.3.0_STM32F7X2
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Support programmable LED like WS2812 etc
Built-in current sensor
Blackbox: 16MB (V2 with BLHeli_32 ESC included)
ESC
Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/TBS Crossfire Receiver (requires external connection)
Input voltage: 2S-6S Lipo
Continuous current: 35A
Peak current: 40A
ESC firmware: BETAFPV_35A_V2_BLHeli_32_Multi_32_9 (BLHeli_32)
Indicators: Power indicator (Red) / FC indicator (Blue)
Capacitance: CS|5*10*13mm|470μF|35V
Connector: 80mm 14AWG silicone cable with XT60
Recommended motors: 14XX series, 15XX series, 16XX series, 18XX series, 20XX series
Includes
1x BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller (w/ 35A 32Bit 4in1 ESC) - ICM42688
Pavo Pico is the tiniest 2S Sub100g DJI O3 Cinewhoop frame, working with other popular HD digital VTX such as Walksnail Avatar Pro Kit, Vista Kit, etc. After testing with pilots, this frame has been upgraded by lowering the battery slot height and adding filters and camera protection parts. These updates enhance the camera and HD digital VTX, to give pilots an unparalleled flying experience.
The Pavo Pico is an all-new HD 81mm cinewhoop with 45mm props that is designed to be the smallest 2S-3S, sub100g build.
Check out the rest of our micro frames and the rest of our BetaFPV gear!
Features
HD digital VTX bracket made of lightweight and tough injection-molded PP material with an adjusted structure to prevent HD VTX displacement or loss after the crash.
Incorporating an angle-limited lens protection print and DJI O3 series filters, It is recommended to purchase, which can increase safety and improve visual quality.
The Rubber Damper Vibration damping design reduces low-frequency vibrations and is used with GyroFlow stabilization software for a stable and clear camera image during high-speed flight.
To accommodate a wider range of battery sizes, the main body of the frame can be trimmed through DIY methods. Additionally, larger batteries can be installed by using battery straps or printed components.
The DJI O3 can be directly installed, while Avatar and Vista require a 20x20 mounting plate and screws (included) for fixation. The naked frame is suitable for users who DIY refit and assemble the HD VTX by themselves.
We offer a wider range of colors for the Pavo Pico frames, giving you even more options to choose from. Whether you prefer a bold and bright hue or a more subdued shade, we have a color that will suit your style. You can choose your favorite color or collect them all to create your own unique mix-and-match cinewhoop.
Pavo Pico Frame Kit
We used ultra-light PP material to make the HD VTX mounting bracket, increasing its toughness. The antenna fixing slot and frame have been fused to reduce damage risk, while the camera's installation height has been lowered with a protective printed part to limit its movable angle to within 30°. Additionally, an O3 filter can be used to protect the lens and enhance image quality. We have incorporated a unique rubber damper vibration-damping design, used with GyroFlow stabilization software, which greatly enhances safety and ensures a smooth, HD image output. When you screw the die-cast screws, please DO NOT screw them too tight to leave room for rubber dampers to absorb vibration. It may cause jello in the video footage.
Click to watch the installation guide video for DJI O3 Air Unit on Pavo Pico.
And The whoop quadcopter package includes the DJI O3 HD Digital VTX Antenna Mount.
DJI O3 Vibration Problem
To tackle the challenge of vibration on many whoop drones, the DJI O3 unit is mounted on a carbon fiber plate with 4 rubber dampers. This innovative design ensures peak performance and perfect stability.
Troubleshooting
To improve video quality when recording with DJI O3 HD VTX, turn off its electronic stabilization and use GyroFlow stabilization software.
When fixing the HD VTX bracket with M1.4*10 screws, ensure that the nut just touches the shock-absorbing ball.
The Jello effect may occur during the above installation due to 2 reasons:
The VTX bracket is over-tightened with the screw and the rubber dumper is totally deformed. To solve this, make sure that the screw is tightened just enough to touch the shock-absorbing ball and keep the ball and bracket loose.
If It is a large deformation of the frame or quadcopter blades, replace the frame or blades with larger vibrations if necessary.
Note: use acetate tape to bind motor wires and prevent them from drooping and interfering with the propeller's rotation.
Upgrade Low Profile Design
After collecting feedback through the BETA TEST, we lowered the height of the HD VTX mounting bracket and whoop duct from 60.6mm to 51.5mm and the battery compartment results in a more low profile on the cinewhoop.
Pilots can further customize their cinewhoop with DIY options such as battery straps or printable components, allowing for compatibility with a variety of battery sizes. This enables pilots to tailor and enhance their cinewhoop to meet their specific requirements and preferences. Steps as follow:
Specification
Item: Pavo Pico Brushless Whoop Frame
Material: PA12
Wheelbase: 80.8mm
Battery Slot Size: 16mmx12.7mm
Camera Installation Spacing: 19mm/20mm
Color: Black
Weight: 11.62g
Motor Mounting Hole Position: 3-M1.4-φ6.6mm
FC Pattern: 26×26mm, suitable for F4 1S 12A AIO Brushless FC V3
Includes
1x BetaFPV Pavo Pico HD 81mm Cinewhoop Frame (HD Digital Version) - Black
The Caddx Nebula Pro Nano features the same great 720p/120fps performance and low 28ms latency of it's big brother the Nebula Pro Micro and weighs in at only 3.5 grams! If you want 120fps low latency HD in a nano form factor, this is your camera!
We also carry the Caddx Nebula Pro Nano Vista Kit!
Check out all our DJI compatible gear and our CADDX product selection!
Specifications
Image Sensor: 1/3 inch CMOS Sensor
Aperture: F/2.0
Resolution: 720p/120fps
Aspect Ratio: 16:9 & 4:3 (Switchable)
Lens Size: 2.1mm f/2.1
Field of View: 150°(D);122°(H);93°(V)°
Latency: 12-28ms (low latency mode), 30-40ms (high quality mode)
Cable Length: 8cm
Dimensions: 16.5x16x14mm
Weight: 3.5g
Includes
1x Caddx Nebula Pro Nano 720p/120fps HD FPV Camera for DJI
1x 8cm Cable
The Caddx Nebula Pro Nano features the same great 720p/120fps performance and low 28ms latency of it's big brother the Nebula Pro Micro and weighs in at only 3.5 grams! If you want 120fps low latency HD in a nano form factor, the Caddx Nebula Pro Nano Vista Kit is your camera kit!
We also carry the camera separately if you're looking to shed some weight on an existing build. Check out the entire DJI System product line, our DJI compatible gear and our CADDX selection!
Features
Lighter than the Air Unit, better suited for micro applications
Low latency mode offers 120FPS at <28 ms!
Embedded Receiver for DJI Remote Controller
Specifications
Coaxial Cable Length: 8cm
Nebula Pro Nano Camera
Image Sensor: 1/3 inch CMOS Sensor
Aperture: F/2.0
Resolution: 720p/120fps
Aspect Ratio: 16:9 & 4:3 (Switchable)
Lens Size: 2.1mm f/2.1
Field of View: 150°(D);122°(H);93°(V)°
Latency: 12-28ms (low latency mode), 30-40ms (high quality mode)
Cable Length: 8cm
Dimensions: 16.5x16x14mm
Weight: 3.5g
Vista Module
Input Voltage: 7.4-26.4V
Output Power: 25mW / 200mW / 500mW / 700mW
Dimensions:
Vista: 30x29x13mm
Camera: 24x19x19mm
Coaxial Cable: 120mm
Antenna: 105x11.2mm
Weight: 28g (+1.5g for Antenna)
Includes
1x Nebula Pro Nano Camera
1x Vista Module
1x Antenna (U.FL)
Capture stunning aerial video with the Caddx Nebula Pro Vista Kit. This lightweight kit comes with a 12cm cable and is designed to ensure a clear, high quality image. The Pro Vista Kit produces vibrant colors, deep contrast, and sharp details with minimal distortion.
The Caddx Nebula Pro Digital FPV Camera Kit is another advanced video transmission module by Caddx and fully authorized by DJI that supports a 5.8GHz digital video signal and 720p 120fps image transmission. The Caddx Nebula Pro with Vista is designed for FPV drones and it can be used with DJI FPV Goggles, which provide digital high-definition pictures and a transmission range up to 4km. The Vista system allows up to eight drones to fly simultaneously. Each operator has an exclusive channel, which helps reduce cross-interference and provides an optimal racing experience.
User can wirelessly connect their Vista Kit to the DJI FPV Remote Controller and DJI FPV Goggles without having to purchase additional receivers, as well mount on racing drones!
Check out the entire DJI System product line, our DJI compatible gear and our CADDX selection!
Features
Lightweight digital image transmission combination
Embedded Remote Controller Receiver
Stable and clear HD video
720p/120fps
28ms of latency over 4km
27g weight
8 video channels
Specifications
Model: Nebula Pro Vista Kit
Weight: Vista Kit(camera included): 25g
Weight(Antenna): 1.5g
Dimensions(Vista Kit): 30 x 29 x 13mm
Dimensions(Camera): 19 x 19 x 20mm
Dimensions(Coaxial Cable): 120mm
Operating Frequency: 5.725-5.850GHz
Transmitter Power(EIPP): FCC/SRRC/MIC: <30dBm
CE: <14dBM
Min. Latency(end-to-end): Low Latency Mode(720p 120fps): 21-28ms
Max. Transmission Distance: FCC/SRRC: 4km; CE: 0.7km
I/O Interface: USB-C, IPEX, 3-in-1port
Supported Flight Control System: F3,F4,F7
Operating Temperature Range: 32° to 104°F (0° to 40°C)
Input Power: 7.4-26.4V
Power Output: 25W/200mW/500mW/700mW
Hardware Included: Vista/Nebula pro/coaxial-cable/antenna
Goggles: Work with DJI goggles
Camera(sensor): 1/3" CMOS
Camera(Lens): 2.1mm
Camera(Shutter): Rolling Shutter
Camera(FOV): 150°(D);122°(H);93°(V)
Includes
Caddx Nebula Pro Vista Kit w/ 12cm Cable - Black
The Caddx Polar Micro Vista Unit is an advanced video transmission module that supports a 5.8 GHz digital video signal and 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency of 32 ms. The vista unit can be mounted on a racing drone and used with DJI FPV Goggles or a remote controller to transmit video, control signals, and flight controller information wirelessly!
Check out all our DJI-compatible gear and our CADDX product selection!
Features
Lightweight digital image transmission combination
Stable and clear HD video
720p 60fps, 32ms/4km
8 channels, 8 drones
Specification
Transmitter Power(EIPP): FCC/SRRC: <30dBm; CE: <14dBm
Max.Transmission Distance: FCC/SRRC:4km;CE:0.7km
Operating Temperature Range: 0°to 40°C（32°to 104°F）
Image Sensor: 1/1.8" Inch 2.3Mega starlight sensor
Supported Flight Control System: BetaFlight
Min.Latency(end-to-end): 720p 60fps<32ms
Polar vista kit Weight (Include camera): 28g
Operating Frequency: 5.725-5.850GHz
I/O Interface: USB-C,IPEX,3-in-1 port
FOV: 162°(D); 138°(H); 75°(V)
Min. Illumination: 0.00003Lux
Antenna Weight: 1.5g(IPEX)
Polar cam: 24×19×19mm
Input Power: 7.4-26.4V
Coaxial Cable: 120mm
LENS: F/1.6
Vista: 30×29×13.5mm
Aspect Ratio: 16:9
Antenna: 105mm
Includes
1x Polar Vista Kit (in silver or coffee colors)
6x M2 screws 3/4/5mm
4x Gasket Ring
1x 3-in-1 cable
1x Menu cable
This is a replacement lens for the Caddx DJI camera, Nebula Pro, Nebula Micro, or Ratel 2 cameras.
Check out all our replacement cam parts & lenses, and our CADDX gear selection!
Includes
1x Caddx Replacement Lens for Nebula Micro/Pro & Ratel 2
The Camera Butter ND Filter Two Pack for the DJI O3 Air Unit Camera helps you get better footage while protecting your camera. This two-pack includes ND8, and ND16, filters featuring Corning Gorilla Glass for high strength durability. These ND filters come with two clip-in slots for a secure connection to your O3 camera. The aluminum frame of the filter is carefully contoured to reduce sharp edges to reduce the wear on your camera.
Check out other DJI O3 Products!
Check out all our replacement cam parts & accessories and all our Camera Butter products!
ND8 Filter: Perfect for cloudy days or early morning/late afternoon sunlight
ND16 Filter: Suitable for use on bright, sunny days
Pro quality optics and Made for Action
Made from incredibly strong Corning Gorilla Glass and ultra premium ND coatings, these ND filters for the DJI O3 air unit will reduce jello caused by vibrations, smooth out your video, minimize your props in view and give you cinema-style, extra smooth motion blur.
Made specifically for the DJI O3 air unit
Unlike filters that are primarily made for the Avata, the Camera Butter O3 filters and lens protectors are specially made for the O3 unit and the FPV use case. This means:
They fit tighter and stay on better than other filters
They are made to fit into a narrower space
They have little "wings" on the top and bottom to make them easier to remove
You can turn them 90 degrees and use the horizontally for extra space on the top and bottom
They are much tougher than other filters made from regular glass
Protect your lens
Both the ND filters and clear lens protectors are the only ones made from ultra-strong Gorilla glass, meaning that they can take a hit much better than other filters. Now you don't have to give up protection if you want to use an ND filter - the ND filters are just as strong. These filters are truly made for action!
Get the very best out of your O3 and protect your camera better than any other filter available!
Easier on your camera
Due to the design of the O3 camera, continually inserting and removing filters can eventually wear away the plastic, which can mean a looser fit over time. Unlike other O3 filters (even ones that look almost exactly the same!), the aluminum frame on thus filter is carefully contoured to reduce sharp edges to reduce the wear on your camera. This is a labor-intensive process, but significantly decreases damage to your expensive camera.
These filters also act as a lens protector that can protect your camera lens when your drone has a severe crash. The UV filter can protect your lens while you fly indoors or at dusk, providing pilots with clearer footage.
Includes
1x Camera Butter ND Filter 2 Pack for DJI O3 Air Unit Camera - ND8/16
The Camera Butter ND Filter Two Pack for the DJI O3 Air Unit Camera helps you get better footage while protecting your camera. This two-pack includes UV/protection ND filters featuring Corning Gorilla Glass for high strength durability. These ND filters come with two clip-in slots for a secure connection to your O3 camera. The aluminum frame of the filter is carefully contoured to reduce sharp edges to reduce the wear on your camera.
Check out other DJI O3 Products!
Check out all our replacement cam parts & accessories and all our Camera Butter products!
Clear UV Filter: Protects your camera lens from dust, dirt, and scratches
Pro quality optics and Made for Action
Made from incredibly strong Corning Gorilla Glass and ultra premium ND coatings, these ND filters for the DJI O3 air unit will reduce jello caused by vibrations, smooth out your video, minimize your props in view and give you cinema-style, extra smooth motion blur.
Made specifically for the DJI O3 air unit
Unlike filters that are primarily made for the Avata, the Camera Butter O3 filters and lens protectors are specially made for the O3 unit and the FPV use case. This means:
They fit tighter and stay on better than other filters
They are made to fit into a narrower space
They have little "wings" on the top and bottom to make them easier to remove
You can turn them 90 degrees and use the horizontally for extra space on the top and bottom
They are much tougher than other filters made from regular glass
Protect your lens
Both the ND filters and clear lens protectors are the only ones made from ultra-strong Gorilla glass, meaning that they can take a hit much better than other filters. Now you don't have to give up protection if you want to use an ND filter - the ND filters are just as strong. These filters are truly made for action!
Get the very best out of your O3 and protect your camera better than any other filter available!
Easier on your camera
Due to the design of the O3 camera, continually inserting and removing filters can eventually wear away the plastic, which can mean a looser fit over time. Unlike other O3 filters (even ones that look almost exactly the same!), the aluminum frame on this filter is carefully contoured to reduce sharp edges to reduce the wear on your camera. This is a labor-intensive process, but significantly decreases damage to your expensive camera.
These filters also act as a lens protector that can protect your camera lens when your drone has a severe crash. The UV filter can protect your lens while you fly indoors or at dusk, providing pilots with clearer footage.
Includes
1x Camera Butter ND Filter 2 Pack for DJI O3 Air Unit Camera - ND8/16
Make the best FPV system ever better! High quality Neutral Density filters made to fit the DJI FPV System (NOT the DJI FPV Drone!), will fit on both the DJI FPV camera and the Caddx FPV camera.
ND Filters can dramatically reduce or eliminate vibration and jello in your goggles and in your DVR, and can also add nice, creamy motion blur to smooth out your video.
The filters comprise of a 3d-printed sleeve that fits over the camera, and an optical neutral density glass filter that is nanocoated on both sides to repel water and make fingerprints easy to clean off.
Check your frame for fit: The filter adapter is 17mm wide at the camera lens, and flares out to about 22mm wide at about 4mm in front of the camera lens.
Choose between a pack containing ND4, ND8 and ND16 or ND8, ND16 and ND32 filters!
Check out all our replacement cam parts & accessories and all our Camera Butter products!
Specifications
ND4: Cloudy, overcast
ND8: Partially cloudy, some sun
ND16: Regular daylight
ND32: Very bright sun
Includes
3x CameraButter ND Filters for the DJI FPV System
Capture better footage and keep your camera safe with the Camera Butter ND Filter Multipack for the DJI O3 Air Unit Camera. This full pack includes ND4, ND8, ND16, ND32, and a Clear UV filter to suit different lighting conditions. It features Corning Gorilla Glass for high strength durability. These ND filters come with two clip-in slots for a secure connection to your O3 camera. The aluminum frame of the filter is carefully contoured to reduce sharp edges to reduce the wear on your camera.
Check out other DJI O3 Products!
Check out all our replacement cam parts & accessories and all our Camera Butter products!
ND4 Filter: Ideal for dark, cloudy days
ND8 Filter: Perfect for cloudy days or early morning/late afternoon sunlight
ND16 Filter: Suitable for use on bright, sunny days
ND32 Filter: Designed for exceptionally bright conditions, such as snow or water reflections
Clear UV Filter: Protects your camera lens from dust, dirt, and scratches
Pro quality optics and Made for Action
Made from incredibly strong Corning Gorilla Glass and ultra premium ND coatings, these ND filters for the DJI O3 air unit will reduce jello caused by vibrations, smooth out your video, minimize your props in view and give you cinema-style, extra smooth motion blur.
Made specifically for the DJI O3 air unit
Unlike filters that are primarily made for the Avata, the Camera Butter O3 filters and lens protectors are specially made for the O3 unit and the FPV use case. This means:
They fit tighter and stay on better than other filters
They are made to fit into a narrower space
They have little "wings" on the top and bottom to make them easier to remove
You can turn them 90 degrees and use the horizontally for extra space on the top and bottom
They are much tougher than other filters made from regular glass
Protect your lens
Both the ND filters and clear lens protectors are the only ones made from ultra-strong Gorilla glass, meaning that they can take a hit much better than other filters. Now you don't have to give up protection if you want to use an ND filter - the ND filters are just as strong. These filters are truly made for action!
The kit comes with 4 different ND values for different lighting conditions, and a clear lens protector to protect your camera when you are not using filters.
Get the very best out of your O3 and protect your camera better than any other filter available!
Easier on your camera
Due to the design of the O3 camera, continually inserting and removing filters can eventually wear away the plastic, which can mean a looser fit over time. Unlike other O3 filters (even ones that look almost exactly the same!), the aluminum frame on this filter is carefully contoured to reduce sharp edges to reduce the wear on your camera. This is a labor-intensive process, but significantly decreases damage to your expensive camera.
These filters also act as a lens protector that can protect your camera lens when your drone has a severe crash. The UV filter can protect your lens while you fly indoors or at dusk, providing pilots with clearer footage.
Includes
1x Camera Butter ND Filter Multipack for DJI O3 Air Unit Camera - ND4/8/16/32/ + UV
Check out Craftedkwads Odonata HD 2" Frame Kit - dual variant
A micro drone that fits in the palm of your hand, rips like a 5", and shares the incredible vision of a dragonfly.
Fast, silent, and small, the Odonata HD is built for stealth, power, endurance, and fun. Spinning 2" props and a compact 95mm wheelbase, the Odonata HD can be flown anywhere, without sacrificing performance and allowing you to use the systems you love!
Be sure to check out all our 2" frames, and all our Craftedkwads Products.
Features
Supports DJI (Naked Vista)
Supports HDZERO (Whoop Lite)
Supports Avatar (1S Lite VTX)
Supports Analog (Nano VTX)
Specifications
Prop size: 2" (51mm)
Frame weight: 11g
Camera mounting: 14x14 m2 (nano)
Weight: 11g
Electronics mounting: 25.5x25.5 m2 (Bottom Plate), 20x20 m2 (Top Plate)
Motor mounting: Ø6.6mm tri-point m1.4, Ø9mm two-point m2
Systems Supported:
DJI (Stripped Air Unit Lite/Vista/Link)
Avatar (Lite VTX)
HDZERO (Whoop Lite)
Analog (Nano vtx)
Includes
1x Craftedkwads Odonata HD 2" Frame Kit - dual variant
1x Body Plate, 2mm thick Carbon Fiber
1x Top Plate, 1.5mm thick Carbon Fiber
3x m2x20mm standoff, Aluminum
6x m2x6mm screw, Steel
1x Nano Camera Mount Set, TPU
1x Rear Mount, TPU
1x Craftedkwads Sticker
This micro drone boasts remarkable performance, fitting in the palm of your hand while providing the same feel as a 5" craft. The Ironclad works with 2" props and has an approximate 50g dry weight. The Odonata HD combines speed, silence, and a dragonfly's-eye view into one powerful package. This Ironclad ripper is designed to take on heavier builds and larger motors with its 2.5mm thick bottom plate.
Be sure to check out all our 2" frames, and all our Craftedkwads Products.
Features
Palm size
Dragonfly like POV
Ultra light weight
Supports DJI (Naked Vista)
Supports HDZERO (Whoop Lite)
Supports Avatar (1S Lite VTX)
Supports Analog (Nano VTX)
Extra Durable bottom plate
Specifications
Motor mounting: Ø6.6mm tri-point m1.4, Ø9mm two-point m2
Electronic mounting: 25.5x25.5 (bottom plate), 20x20 (top plate)
Camera mounting: Nano (14x14)
Prop size: 2"
Weight: 13g
Top Plate: 1.5mm
Bottom Plate: 2.5mm
VTX systems supported:
DJI: naked vista
HDZERO: Whoop Lite
Avatar: 1S lite VTX
Analog: Nano VTX
Includes
1x CraftedKwads Odonata HD 2" Ironclad Micro Frame Kit
Fly faster, and stronger with DLQFPV Asbo XL 3.5", now at RaceDayQuads! Experience unparalleled control with this lightweight & durable frame. The XL takes design cues from the X but adds support for double 20x20 mounts, so pilots can run a 20x20 stack and a DJI air unit Lite front and back. The ASBO XL also supports 3.5 inch propellers and is shipped ready to run with a TPU canopy or a carbon fiber hard top. Being made of lightweight and durable carbon fiber and comes with all the necessary hardware for easy assembly.
Be sure to check out all our Micro Frames, and all our DaddyLovesQuads products!
Specifications
Wheelbase: 170mm
Size: 3.5"
3K carbon
Motor Mounting: 9x9mm/12x12mm M2
Includes
4.5mm 3K carbon fiber base plate
2.5mm 3K carbon fiber top plate
3D printed TPU canopy
3D printed TPU camera mount (for hard top)
3D printed antenna mounts (Crossfire and VTX)
2x20mm knurled aluminum standoffs
4x23mm knurled aluminum standoffs
4x 8mm screw
4x 10mm screw
TPU Arm guards and Canopy
Diatone Mamba Micro 2A SWITCHABLE BEC 5V/9V for DJI Air Unit! This unit conveniently switches between a 5v and 9v output at 2 Amps!
Check out all our BECs and our Diatone products!
Specifications
Output: 5V/2A and 9V/2A switchable
Output 5V: input 7~25.2v
Output 9V: input 12~25.2v
Product Size：16×10mm
Weight: 1.6g
Includes
1x Diatone 2-6S Mamba Micro BEC 2A 5V/9V for DJI Air Unit
The Diatone Mamba MK4 is an F722 flight controller. With WiFi capabilities through the SpeedyBee APP, this stack is the perfect addition to your FPV build. This version has an IMC42688P Gyro.
Check out all our 30x30 FCs and all our Diatone Gear!
Specifications
MCU: STM32F722
GYRO: IMC42688P
Barometer: Yes
OSD: Yes
Blackbox: 16M Flash Memory
Uarts: 6Set
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED/MB LED
F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 3-6S Lipo
TVS Protection: Yes
BEC: 3.3V/0.5A, & 5V/3A, and 9V/3A
Mounting: 30.5x30.5mm, M3
Includes
1x Diatone Mamba DJI F722 APP MK4 30x30 Flight Controller
5x M3 ESC Isolation Dampers
5x M3 Silicone Dampers
1x 6-Pin Air Unit Cable
2x 8-Pin Cable
Wiring Diagram
Diatone has released their 4th generation F722 mini stack. The MK4 F722 mini 20x20 stack boasts larger soldering pads, wider pad spacing, more UARTs, l2C and is configurable through the Speedy Bee App via built-in Wi-Fi! So much power from a lightweight stack!
Browse our Stacks & Combos and our Diatone Gear!
Features
The pad area increased by 30%
Pad spacing increased by 100%
MP9943 synchronous rectifier BEC
MINI series upgrade DJI interface and 5v 15W/9V 18W 2 set BEC
USB Type C
6 Set UART and I2C
4 Set Power Protection
32Bit ESC all support 128K
Mini series FC uses 2mm and 3mm mounting holes, w/ a special dampening ring
Upgrade the twisted pair anti-jamming cable and reinforcement process
Specifications
Mamba Basic Mini F722 MK4
Input: 2-6S
MCU: ICM42688P
Barometer: Yes
OSD: Yes
Blacbox: 16M Flash Memory
Uarts: 6Set
Protocol: Dshot300/600/1200
ESC Telemetry: Yes
Power Led: Yes
LED Controller: BF LED
F.Port: Yes
Buzz: Yes
TVS Protection: Yes
BEC: 3.3V 0.5A & 5V 2.5A
Mounting Pattern: 20x20 M3/M2
Mamba F40 128k
Input Voltage: 3-6S Lipo
Max Continuous Current: 40A
Max Burst Current: 45A
BEC: No
Target：BLHeli_32 MAMBA F40_128K_MINI
Protocol: Dshot300/600/1200
PWM Range: 24~128K
TVS Protection: Yes
Mounting Pattern: 20x20 M2/M3
Includes
1x Diatone Mamba Basic MK4 F722 Mini F40_128k 2-6S 20x20 Stack/Combo
5x M2 Silicone Grommets
5x M3 Silicone Grommets
5x M2 ESC Isolation Columns
5x M3 ESC Isolation Columns
1x 8 Pin single-ended cable for flight controller
2x 8 Pin Cable
1x 6 Pin Air Unit Cable
1x XT60
1x Capacitor
Wiring Diagram
Another great option for those DJI builds, just grab the pigtail adapter of your choice to connect to your air unit.
Check out all our VTX Antennas and all our Diatone Gear!
Specifications
Frequency range（MHz）：5500-6000
Polarization：LHCP
Gain（dBi）：2.5
VSWR（5800MHZ）：≤1.5
Input connector type：SMA
Radome material: ABS
Radome color: Black
Operating temperature（°c）:-40～60
Rated Wind Velocity（m/s）:60
Weight: 7.6g
Includes
1x Diatone Mamba Ultra 5.8GHz SMA Antenna - LHCP
If you purchased a BNF with a Caddx Vista this arm will NOT fit, the Roma 5 BNF w/ Caddx Vista uses the standard frame. Find the arms here.
Replacement part for the Diatone Roma F5 5" Frame for DJI
Check out Diatone Roma F5 DJI Edition & Accessories, our DJI compatible gear and our Diatone products!
Includes
1x Diatone Roma F5 5" Frame for DJI Arm (1PC)
This DIY wiring harness kit takes the guess work out of hunting for the perfect fit for your 4 in 1 ESCs, Flight Controllers, VTXs and Cameras! Stop hoping your have the right pinout laying around and make your own! The combo set has been updated to include more JST GH locking connectors since that's what is used on DJI Air Units and several other VTX models. Choose the correct version for your needs. Available with JST-SH1.0, JST-GH1.25 & Molex PicoBlade 1.25, or just JST-SH 1.0.
Currently, wires in this DIY Cable set will not fit JST-GH (Locking) connectors.
Check out the rest of our Tools & Building Supplies!
Features
Silicone wire - Flexible and wont shrink with heat from your soldering iron!
Pre-crimped ends on both sides of the wire.
Male pieces only, since that is what is used most often in wiring harnesses
JST SH / JST GH / Molex Pico Blade Version Includes
Double Crimped Silicone Wires
20x 50mm
17x 100mm
12x 150mm
JST-SH (1.0mm Pin Spacing)
5x 3 Pin
10x 4 Pin
5x 5 Pin
5x 6 Pin
2x 7 Pin
2x 8 Pin
2x 9 Pin
2x 10 Pin
2x 11 Pin
2x 12 Pin
Molex Pico Blade (1.25mm Pin Spacing)
2x 2 Pin
2x 3 Pin
4x 4 Pin
2x 5 Pin
2x 6 Pin
2x 7 Pin
2x 8 Pin
JST-GH (1.25mm Pin Spacing w/ lock)
2x 2 Pin
2x 3 Pin
2x 4 Pin
2x 5 Pin
4x 6 Pin
2x 5 Pin
4x 8 Pin
JST SH ONLY Version Includes
Double Crimped Silicone Wires
12x 150mm
12x 100mm
12x 50mm
JST-SH (1.0mm Pin Spacing)
10x 3 Pin
10x 4 Pin
4x 5 Pin
4x 6 Pin
2x 7 Pin
2x 8 Pin
2x 9 Pin
2x 10 Pin
2x 11 Pin
2x 12 Pin
Spare replacement 3in1 Cable for the DJI Digital FPV Air Unit
The 3-in-1 cable connects quickly to the air unit module port. The power cable and signal cable are both marked in different colors.
See all our DJI FPV System Parts & Accessories!
Specifications
Length: 205 mm (without terminal)
Includes
1x DJI FPV Air Unit 3in1 Cable
Spare replacement Coaxial Cable for the DJI Digital FPV Camera Module and Air Unit. The coaxial cable can be quickly installed to the camera's back cover and the air unit module. Very thin coaxial cable is used with the exposed part wrapped by TPU to improve bending and wear resistance.See all our DJI FPV System Parts & Accessories!
Specifications
Length: 100 mm (without terminal, trailer card and back cover)
Includes
1x DJI FPV Air Unit Coaxial Cable
Set of spare replacement 90 Degree Elbow MMCX Antennas for the DJI Digital FPV Air Unit. LHCP antenna with MMCX joint, which is small and lightweight and ensures a long-distance transmission range and strong anti-interference. Long-distance transmission, small size, lightweight, and durable.
See all our DJI FPV System Parts & Accessories!
Specifications
VSWR<2 frequency range: 5.4GHz-6GHz, 2.75dB gain and 3dB axial ratio beamwidth at 5.8GHz
Size: 12.7 × 12.7 × 80 mm
Weight: 3.9 g
Tips
Keep the antennas of the air unit at least 40 mm apart.
Keep the air unit away from metal objects or carbon fiber frames. Make sure to choose a position where the transmission will not be blocked during flight.
The DJI FPV Air Unit is equipped with MMCX antenna ports. Since the port (the inner pin) is small, when pulling out the antenna, please hold the air unit with one hand, press the two ends of the antenna with the other hand, and remove it horizontally.
Please note that dragging the antenna directly may cause the inner pin and the collar to fall off or get damaged.
Includes
2x DJI FPV Air Unit Antenna - Elbow MMCX
