BlackZon Slyder Monster Truck (MT) Turbo 1/16 4WD RTR 2S Brushless
4WD Shaft Driven Truck
Independent Double Wishbone Suspension
Adjustable Coilover Shocks
4-Gear Differentials Front & Rear
Metal Rear Drive Shafts
Gear Cover To Keep Debris Away From The Spur Gear
Dual Point Bell Crank Steering System
Servo Saver Built into Servo Horn
Complete Set of Ball Bearings
Splashproof Electronics
3800KV Brushless Motor
2.4GHz Radio with 2 in 1 Brushless ESC/Receiver - 2S Capable
2S 7.4V 1000mAh LiPo Battery w/ T-Plug connector
USB Charger
Speed Limiter using Speed Dial on Transmitter
Front LED Lights included in box (customer to fit if desired)
Wheelie Bar included in box (customer to fit if desired)
Notes:
2S Capable
Different model to Brushed car - Increased Range and Steering D/R
Features:
ESC: 2in1 Brushless ESC
Motor: 3800KV Brushless Motor
Servo: 3 Wire
Radio: 2.4GHz 2 Channel
Battery: 2S 7.4V LiPo - 1000mAh 25C
Charger: USB
Specifications:
Length (mm): 270
Width (mm): 215
Height (mm): 130
Wheelbase (mm): 175
This product was added to our catalog on November 11, 2023
BlackZon Slyder Short Course Truck (ST) Turbo 1/16 4WD RTR 2S Brushless
4WD Shaft Driven Truck
Independent Double Wishbone Suspension
Adjustable Coilover Shocks
4-Gear Differentials Front & Rear
Metal Rear Drive Shafts
Gear Cover To Keep Debris Away From The Spur Gear
Dual Point Bell Crank Steering System
Servo Saver Built into Servo Horn
Complete Set of Ball Bearings
Splashproof Electronics
3800KV Brushless Motor
2.4GHz Radio with 2 in 1 Brushless ESC/Receiver - 2S Capable
2S 7.4V 1000mAh LiPo Battery w/ T-Plug connector
USB Charger
Speed Limiter using Speed Dial on Transmitter
Front LED Lights included in box (customer to fit if desired)
Wheelie Bar included in box (customer to fit if desired)
Notes:
2S Capable
Different model to Brushed car - Increased Range and Steering D/R
Features:
ESC: 2in1 Brushless ESC
Motor: 3800KV Brushless Motor
Servo: 3 Wire
Radio: 2.4GHz 2 Channel
Battery: 2S 7.4V LiPo - 1000mAh 25C
Charger: USB
Specifications:
Length (mm): 270
Width (mm): 215
Height (mm): 130
Wheelbase (mm): 175
This product was added to our catalog on November 11, 2023
CSE010-0115-00, Castle Creations Sidewinder 3 Waterproof 1/10 Sport ESC
This is the Castle Creations Sidewinder 3 Waterproof 1/10 Sport ESC. Castle’s Sidewinder ESC is now waterproof! The Sidewinder 3 can power crawlers on water filled trails, AWD's in rain soaked parking lots, and SCT's on adventures through muddy fields. Drivers can now give in to those irresistible urges to drive in the mud or rip through puddles without damaging their ESC.Designed for 1/10thThe Sidewinder 3 is a great fit for 1/10th off-road, on-road, and rock crawlers running up to 3S LiPo. It features updated circuitry for faster response time and improved reliability. As always, the Sidewinder 3 offers industry-leading software functions and USB programming capability via Castle Link USB adapter (sold separately).Amazing PriceThe Sidewinder 3 offers world class performance at an entry level price.Legal mumbo jumboAlthough Sidewinder 3 and Castle brushless motors are waterproof, always rinse the ESC and motor with fresh water after exposure to corrosives or dirt. While the motor and controller may be waterproof, Castle suggests users confirm that the rest of their vehicle, including the batteries, servo, radio and chassis, are also waterproof before exposing them to liquids of any kind.
Specifications:
Input Voltage: MIN: 2s LiPo; MAX: 3s LiPo
BEC: 5.0V, 2A
Operating Environment: Waterproof* design allows for use in nearly any environment.
Brake: Proportional
Reversible: Yes - with lockout
Size (LxWxH): 1.93x1.48x0.79" (49x38x20mm)
Weight (w/127mm long battery wires and no battery connector): 1.96 oz (55.5g)
*Not intended for operation while submerged in liquid. If unit is operated in wet conditions, rinse with fresh water to remove dirt or corrosives, then fully dry unit.
This product was added to our catalog on January 20,2024
CSE010-0150-02, Castle Creations Sidewinder Micro 2 1/18th Scale Brushless Car Package (5300KV)
The Sidewinder Micro 2 ESC boasts updated circuitry and added functionalities. Castle engineers are committed to taking full advantage of advancements in component quality and continuous improvements in software design. As a result, we are thrilled to introduce the Sidewinder Micro 2. The Sidewinder Micro 2 is perfect for 1/18th scale 2WD vehicles and smaller 4WD (up to 2 lbs.) such as the Team Associated RC18B2 or Dromida SC4 SCT. Whether you are converting to a brushless setup or simply needing more power than your current brushless power system is putting out, there is a Sidewinder Micro 2 combo to fit your needs. The Castle 20mm 0808 Brushless Motors are a perfect companion to the Sidewinder Micro 2 and are available in 4100Kv, 5300Kv, or 8200Kv packages.
The included 0808 series 5300Kv motor is suitable for on-road and off-road applications running up to 3S LiPo and weighing in at up to 2.5lbs. Using the same 4 pole technology found in the larger Castle motors, the 0808 series provides the increased efficiency and torque 4 pole motors are known for.Sidewinder Micro 2 Features:
Improved BEC Functionality - Now adjustable: 5.5V or 7.5V
Improved Audible Alerts - The ability to diagnose and resolve problems in the field are made easy as this ESC will communicate with audible tones when certain conditions are present. Alerts are present for start fail, voltage cutoff, radio glitch, over-temperature, over-current and excessive load detections.
Improved Startup - Updated circuitry and refined software makes for ultra-smooth starts!
Link Live functionality added - Link Live is a way for the controller to communicate power system information to an external device. This feature, when enabled, will allow users to experience real-time telemetry data such as battery voltage, ESC temperature, motor power output and battery ripple. Compatibility with the Futaba S.BUS® T4PX transmitter is coming soon (Requires purchase of Castle S.BUS2 Telemetry Link)
Transmitter Programming - Manual programming settings include Brake/Reverse Type, Voltage Cutoff, Brake Amount, Drag Brake and Motor Type.
Castle Link Programming - With the purchase of Castle Link USB device, you will have access to the full programming suite of adjustable settings that tune and tweak your vehicle to your preferences, resulting in an incredible driving experience! Click here for the full list of Castle Link Sidewinder Micro 2 settings.
Firmware Updates - With the purchase of Castle Link USB device, you will have access to all firmware updates, including added feature sets released from Castle Engineering at no charge.
Specifications:
Sidewinder Micro 2 ESC
Application: 1:18th scale RC hobby vehicles weighing up to 2 lbs.
Input voltage: 2S-3S LiPo, 4-9 cell NiMH
BEC Specifications: Adjustable: 5.5V or 7.5V (2A Peak), default 5.5V
Size: ~22mm x 38mm
Weight (w/wires): ~26g
Connector Type: The Sidewinder Micro 2 has 3.5mm bullet connectors on the motor wires and the battery input wires are bare. You must add the connector of your choice to the battery leads. We recommend a high current connector rated for at least 40 amps.
0808 20MM Brushless Motor
Kv: 5300Kv
Size: L: 1.5" (38mm) Diameter: 0.79" (20mm) Shaft: 0.08" (2mm)
Weight: 1.8 oz (50g)
Connector Type: 3.5mm gold connectors (female connectors included)
Maximum Input Voltage: 2-3S LiPo, 4-9 cell NiMH (2S max 8200Kv)
This product was added to our catalog on March 2, 2021
CSE010-0165-00, Castle Creations Mamba Monster X 8S 1/6 Brushless ESC
The Castle Creations Mamba Monster X 8S 1/6 Brushless ESC features CRYO-DRIVE™ - Castle’s latest break-through technology. CRYO-DRIVE minimizes the amount of time the ESC’s electrical components spend generating heat. This proprietary software advancement works in parallel with a unique open housing design and a forged elliptical fin heatsink to allow increased directional airflow to cool critical components. Combine this with a high speed 40mm fan and you have a design that maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling.
Mamba Monster X 8S is designed for 1/6 scale vehicles weighing up to 25 lbs. with up to 8S LiPo.
Compatible models include the Traxxas X-Maxx & Unlimited Desert Racer; Arrma Kraton 8s & Limitless; Losi Super Rock Rey & Audi R8; Redcat Shredder.
Features:
Input voltage range 2S-8S LiPo
Sensored, Sensorless and SmartSense™ running modes
Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V)
Premium forged heatsink with elliptical fins for superior airflow and increased heat dissipation
Oversized factory equipped thermally controlled 40mm fan ? Waterproof design for all weather conditions
ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the components and promote efficient heat transfer
Data-logging capability to capture and record performance data from your vehicle
Auxiliary wire functionality for “on the-fly” adjustments using your transmitter
Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff
Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake
Easily tune and update ESC with USB and Bluetooth™ programming options
Castle Link USB programming kit (coupon included with purchase)
Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store
Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1 year warranty
Specifications:
Application guidelines: 1:6 scale RC hobby vehicles weighing up to 25 lbs
Running Modes: Sensored, Sensorless and SmartSense™ (when paired with a Castle 4-POLE 12SLOT sensored motor)
Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V
BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. Or 8.0V (8A Peak), default 5.5V
Operating environment: Waterproof design enables use in nearly any environment
Brake: Proportional
Reversible: Yes, but may be disabled for racing
On /off switch: Yes, waterproof
Cooling fan: Yes, factory equipped (40mm), fully removable (See Product Use Statements for more info)
Size: L x W x H 69.5mm x 54.1mm x 47mm
Weight (w/wires): 5.75 oz. (163 grams)
Connector type: 6.5mm female bullets for motor connection
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately).
Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters.
This product was added to our catalog on May 14, 2021
CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV)
The Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo with 2028 Sensored Motor is a great way to take your build to the next level with Castle’s cutting edge sensored large scale brushless power. The MAMBA MONSTER X 8S COMBO is ready to power any R/C vehicle weighing up to 25lbs, and running all the way up to 8S LiPo. This motor and ESC combo is designed for heavy, high speed rigs, and you'll experience smooth low-end control, without sacrificing power, punch, or speed.
The MAMBA MONSTER X 8S utilizes Castle’s breakthrough technology, CRYO-DRIVE. By reducing the rate at which the ESC heats up and removing heat more efficiently, your setup will be able to handle higher gear ratios, in heavier vehicles, with longer runs. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 40mm cooling fan and a forged elliptical fin heatsink, the design maximizes airflow throughout the system, taking thermal performance to a whole new level.
The ESC was designed with a robust aluminum casing, and the epoxy potting guarantees protection around the circuitry and ensures all-weather use. Mamba Monster X 8S is a beast, ready to take on the harshest of environments and still perform. You can easily optimize the ESC for any driving condition, from rugged terrain to smooth pavement to the perils of rock and gravel. Create, save and download setup profiles through the Castle Link Programming Suite on your Windows™ PC, or wirelessly with the convenience of the new B-Link™ Bluetooth™ Adapter and Castle Link app for Android or iOS.
When paired with the Castle sensored 2028-800KV motor, users with heavy, high power rigs will experience controllable low-end control without sacrificing power, punch or speed. SmartSense™ mode uses the motor’s sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is spinning, it seamlessly transitions to Castle’s ultra-efficient sensorless mode. You’ll put more power to the ground, where it should be, instead of wasting it through raw heat and RPMs.
NOTE: This is not a direct replacement to the Mamba XLX. The XLX still handles rawer full throttle power in the most extreme setups.
Features:
ESC:
Input Voltage Range 2S-8S LiPo
Sensorless, Sensored and SmartSense™ Running Modes
Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V)
CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs
ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the electronics and promote efficient heat transfer
Premium forged heatsink with elliptical fins for superior air flow and increased heat dissipation
Oversized factory equipped thermally controlled 40MM cooling fan
Compatible with S.BUS2 Telemetry Link and Futaba T4PX and T7PX transmitters
Waterproof design for all weather conditions
Data logging capability to capture and record performance data from your vehicle
Auxiliary wire functionality for "on-the-fly" adjustments using your transmitter
Audible alerts for easy diagnosis of common issues such as motor-over-temperature and low-voltage cutoff
Convenient transmitter programming for six common adjustable settings including cutoff voltage and drag brake
Easily tune and update ESC with USB and Bluetooth™ programming options
Castle Link USB programming kit (coupon included with purchase)
Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store
Proudly designed and manufactured in Olathe, KS USA and backed by Castle Creations' 1-year warranty
Motor:
The 2028 Extreme can easily run in the 10 horsepower range (Burst power output for duration's typical of vehicle acceleration.)
Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode.
High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions.
Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible.
Proprietary winding techniques allow Castle Creations to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor.
Dual sensor ports to ensure optimal installation in your large-scale vehicle.
Updated modern and sleek design that looks as cool as it performs.
Specifications:
ESC:
Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V
BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V
Operating Environment: Waterproof* design allows for use in nearly any environment.
Brake: Proportional
Reversible: Yes, but may be disabled for racing.
On/Off Switch: Yes, waterproof
Cooling Fan: Yes, factory equipped (40MM), fully removable** (See Product Use Statements below)
Size: L x W x H 69.5mm x 54.1mm x 47mm
Weight (with no battery connector): 5.75 oz. (163 grams)
Connectors: 6.5mm female bullets for motor connection
Motor:
Input Voltage Range: 12S MAX
Kv: 800
Max. RPM: 45,000
Minimum Input Voltage: 3S
Maximum Input Voltage: 12S
Sensored Capable: Yes
Can Length: 4.4" (113.2mm)
Can Diameter: 2.2" (57mm)
Weight (w/wires): 44 oz./1.25kg
Shaft Size: Length: 30mm
Diameter: 8mm
Mounting Hole Specifications: 4mm holes @ 30mm spacing.
Cooling Fan: Available, but not included. See 011-0019-00 here.
Connectors: 8.0mm male connectors
Recommended ESC: Mamba XL X
Running modes: Sensorless and Sensored
Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs.
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately).
Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters.
Product Use Statements:
Recommended battery capacity for 1:6th scale vehicles is 5000mah. Castle recommends using 50C continuous discharge or higher LiPo batteries.
Surge ratings should never be used to determine a pack’s suitability for a brushless application.
Castle recommends a high current connector designed for high-powered electric systems, rated for 100+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors.
Applying voltages higher than 33.6V will cause irreparable damage to ESC.
Although Mamba Monster X 8S is waterproof, it is NOT intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt.
The cooling fan must be removed prior to driving in wet conditions. *Fan is not waterproof.
Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the motor or ESC.
The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the Running & Maintaining document in the resources tab above for info on running and maintaining motors in wet environments.
Application Guidelines: Mamba Monster X 8S and 2028-800Kv motor is intended for use in 1:6 scale vehicles weighing up to 25 lbs. and up to 8S LiPo. Vehicle Examples: Traxxas™ X-Maxx & Unlimited Desert Racer; Arrma™ Kraton 8s & Limitless; Losi™ Super Rock Rey & Audi R8; Redcat™ Shredder (optional motor mount and modifications may be necessary to install motor).
Includes:
Mamba Monster X 8S ESC
4-POLE Sensored 2028-800KV Motor
Castle Sensor Harness Adapter (installed)
250mm Sensor Wire
Mamba Decals
Coupon for free Castle Link USB
ESC Quick Start Guide
Motor Quick Start Guide
This product was added to our catalog on April 4, 2021
CSE010-0166-09, Castle Creations Copperhead 10 Waterproof 1/10 Sensored Combo w/1412 (3200Kv) (SCT Edition)
The Castle Creations Copperhead 10 1/10 Sensored "SCT Edition" Combo provides 1/10 scale enthusiasts of all disciplines with a powerful and performance driven ESC that is packed with features. The Copperhead 10 is an affordable option that sits directly in the middle of the Sidewinder 4 entry-level upgrade ESC and the extreme performance MAMBA X option. The Copperhead 10 utilizes CRYO-DRIVE technology, sensored motor support and data logging to deliver Castle’s signature performance and reliability. Whether crawling the rocks, bashing in the backyard or ripping up the local skatepark, Copperhead 10’s versatility will appeal to a wide variety of 1/10 scale enthusiasts.Castle Creations 1412-3200kv Sensored 4-Pole Brushless Motors combine rotor position sensor technology with an improved high power and high efficiency motor design to deliver ultra smooth startup, precise low speed control, predictable power delivery, incredible torque, and lightning fast response. Through the use of Castle's Smart Sense technology, the position of the rotor is always known by the ESC. This eliminates the possibility of encountering cogging or inconsistency during startup, and allows the 1412 to deliver PRECISE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for.
NOTE: Not compatible with Castle Field Link program card (CSE010-0063-00).
Features:
CRYO-DRIVE™: CRYO-DRIVE™ technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs. COOLER TEMPS mean LONGER RUNS and MORE POWER in a COPPERHEAD 10 setup.
DATA LOGGING LITE: Battery Voltage, Battery Ripple, Controller Temperature, Motor RPM and Motor Temperature data points can be captured, downloaded and analyzed via Castle Link software. While not a full version of Data Logging capabilities that the MAMBA X EXTREME 1:10 SCALE ESC has, these critical parameters are excellent sources of information for maximizing performance and battery life of the COPPERHEAD 10.
SMARTSENSE™ TECHNOLOGY: SMARTSENSE uses the motor’s sensors at startup to provide cog-free starts, excellent torque and low speed drivability. Once the motor is turning, the ESC seamlessly transitions to Castle’s ultra-efficient sensorless mode with electronic timing to advance timing automatically for peak performance in all driving conditions. (Requires use of Castle brushless motor to utilize)
INTERNAL BEC (Battery Eliminator Circuit): COPPERHEAD 10 features a selectable 5.5V or 7.5V (6A peak) internal BEC to supply power to many of today’s high-torque servos, without requiring the use of an external BEC.
DUAL USE FAN GUARD: For crawler setups or others that do not require an ESC cooling fan, the fan is easily removed with four screws and the fan guard with the cool COPPERHEAD logo simply clicks back into place on the top of the ESC. It keeps the COPPERHEAD 10 looking mean and provides an extra measure of protection.
APPLICATION SPECIFIC MOTOR COMBOS: Available with a dozen different 4-POLE 12-SLOT sensored motor options to eliminate the guesswork in finding the right brushless power upgrade for your basher, crawler, on road vehicle, short course or monster truck (Motor not included).
WARRANTY: The COPPERHEAD10 is proudly designed and manufactured in Olathe, Kansas USA and backed by the Castle Creations one-year warranty.
FULLY PROGRAMMABLE: Complete Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or wirelessly with the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (B-Link not included).
TELEMETRY LINK CAPABLE: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX
Specifications:
ESC:
Recommended Motors: Castle 1406, 1410, 1412 and 1415 Series Sensored 4-Pole Brushless Motors
Running Modes: SMARTSENSE™, Sensored Only and Brushed motor operation
Input Voltage Range: 2s-4s (16.8V)
BEC Specifications: Selectable: 5.5V or 7.5V (6A peak)
Operating Environment: Waterproof design, potted in durable injection molded case, allows or use in nearly any environment.
Data Logging: Yes, Data Log Lite with 5 data points. Sample frequency of 1 and 5 per second.
Connector Type: 4mm female bullets for motor connection
On/Off Switch: Yes
Cooling Fan: 30mm removable fan included, operates from start up. Purchase also includes a dual use fan guard for use without fan.
Size: 2.19x1.39x1.33" (L x W x H with fan)
Weight: 70.9 g / 2.50 oz. (with fan)
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (sold separately) and freely downloadable Castle Link Windows software.
Motor:
Model: 1412-3200Kv
Input Voltage Range: 2s-4s
Kv: 3200
Max. RPM: 100,000
Length: 62.5mm
Diameter: 36mm
Shaft Size: 15mm x 1/8" (3.17mm)
Weight (w/wires): 265.4g (9.4oz)
Mounting Hole: M3 @ 25mm
Connectors: 4mm male Castle Bullet Connectors
Application Guidelines: 2s-4s on 2WD/4WD SC Trucks
Max. Recommended Vehicle Weight: Vehicles weighing up to 6.5 lbs. ready-to-run
Needed to Complete:
Battery Connector - Castle 4mm polarized connectors, XT60, Dean's Ultra Plug, or Traxxas Power Connector recommended.
Product Use Statements:
Although COPPERHEAD 10 is waterproof, it is not intended for operation while completely submerged in liquid. They can corrode when exposed to corrosive materials, such as salt water. Always rinse the ESC with clean water after exposure to corrosives or dirt.
Remove cooling fan prior to driving in wet conditions, it is not waterproof.
This product was added to our catalog on October 29, 2024
CSE010-0167-00, Castle Creations Mamba XLX 2 1/5 Scale Sensored Brushless ESC
The Castle Creations Mamba XLX 2 1/5 Scale Sensored Brushless ESC is a product guaranteed to redefine the limits of large scale R/C. Though it shares the name of its predecessor, the Mamba XLX, this is an ESC that lives in a class of its own.
Reengineered from the ground up, the Mamba XLX 2 is packed with a potent combination of design, hardware and software advancements that will set a new standard for large-scale power systems. Designed for 1/5 Scale models weighing up to 42 lbs, the XLX 2 is an incredible power upgrade for the Losi DBXL-E and Super Rock Rey, Arrma Kraton 8S and Outcast 8S, or Traxxas X-Maxx models! If you are looking for the ultimate upgrade for your speed run, drag racing or off road rigs - the XLX 2 is a true heavyweight, with no contenders.
CRYO-DRIVE: MORE POWER – COOLER TEMPS – LONGER RUNS
Castle’s latest break-through technology, minimizes the amount of time the ESC’s electrical components spend generating heat. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 50mm fan and a forged elliptical fin heatsink, the design maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling.
NOTE: Some vehicles may require aftermarket parts to allow ESC and/or motor fitment.
Features:
Sensored, Sensorless and SmartSense™ running modes
Powerful Integrated 20A Peak Adjustable BEC (5.25V-8.0V)
Premium forged heatsink with for superior airflow and increased heat dissipation
Oversized factory equipped thermally controlled 50mm fan
Waterproof design for all weather conditions.
ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the components and promote efficient heat transfer
Data-logging capability to capture and record performance data from your vehicle
Auxiliary wire functionality for “on the-fly” adjustments using your transmitter
Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff
Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake
Easily tune and update ESC with USB and Bluetooth™ programming options.
Castle Link USB programming kit (coupon included with purchase)
Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store.
Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1-year warranty
Specifications:
Input voltage range: 3S-8S LiPo
Length: 3.98” (101.2mm)
Width: 2.49” (63.3mm)
Height: 2.2” (55.8mm)
On/Off Switch: Yes, waterproof*
Cooling Fan: Yes, thermally controlled factory equipped (50mm) fully removable**
Weight: 13.1 oz (371g)
Running Modes: Sensored, Brushed, Sensorless and SmartSense™ when paired with a Castle 4-POLE 12-SLOT Sensored Motor. (Dust cover included in package for non-sensored operation)
Wire Gauge: 8AWG
Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX, T7PXR Transmitters.
Items Needed: Connectors designed for 150+ amps continuous, such as Castle 6.5mm polarized or CC BULLET 8.0MM
Includes:
Mamba XLX2 ESC
300mm Direct Connect Sensor Wire
Mamba Decals
Coupon for free Castle Link USB
Motor connection wire, bullets and shrink (not included with combos)
Mamba XLX2 Quick Start Guide
Sensor port dust cover
This product was added to our catalog on March 19, 2021
CSE010-0176-00, Castle Creations Sidewinder Nano Micro Brushless/Brushed ESC (12.6V)
Castle Creations Sidewinder Nano Micro Brushless/Brushed ESC (12.6V). A performance upgrade solution to the ever-growing micro-scale scene in R/C! Capable of running on 2-3S (7.4 - 11.1 Volts) LiPo batteries, this Sidewinder Nano is intended for 1/24 and 1/18 scale RTR (Ready-To-Run) and kit platforms to provide precise throttle control, supreme power-punch, tuneable parameters and unmatched durability and reliability!
The Sidewinder Nano comes equipped with Castle Creations proprietary CRYO-DRIVE Technology resulting in improved thermal performance during partial throttle operation where the majority of driving occurs, resulting in extremely efficient output and reducing stress on the ESC. In addition, the Sidewinder Nano can also be “tuned” for the drivers’ preferences using a Windows based PC and a Castle Link USB adapter (CSE011-0119-00 - sold separately), or with a mobile device using a Castle B-Link Adapter (CSE011-0135-00 - sold separately), allowing tuning and switching parameters to conveniently be done on the fly!
Ideal for:
1/24 2WD or 4WD vehicles up to 1lbs
1/24 and 1/18 crawlers up 2.25lbs (No rock racing/Hill climbing)
Features:
Perfect fit and upgrade for most 1/24 and 1/18 micro platforms
Selectable brushless or brushed
CRYO-DRIVE technology
Castle B-Link adapter compatible
Tune-able parameters
Extremely lightweight and compact
Specifications:
Application: 1/24 and 1/18 scale 2WD or 4WD
Type: Sensorless Brushless/Brushed
Input Voltage: 2-3S (7.4-11.1V) LiPo
Continuous Current: -
Burst Current: -
BEC Voltage: 5A Peak
Input Lead: -
Motor Leads: -
Programmable: Yes
Includes:
(1) Castle Creations Sidewinder Nano Micro ESC
This product was added to our catalog on September 9/2024
ELCNITRIDE110, Elceram Nitride 1/10 Brushless ESC w/LCD Display
Features:
A color display with Thin-Film-Transistor (TFT) LCD (Liquid-Crystal Display) technology, with a resolution of 160x80 pixels.
Self-diagnostic before the race: motor temperature, sensor cable, battery
Post-race data evaluation
Race data logging
Fully programmable all through the ESC without the need for a program card or wireless module
Realtime Data monitoring of the battery voltage, ESC, and motor temperatures
Advanced Aluminum Nitride Ceramic Cooling Technology
Extremely low internal resistance based on silver conductive layer
70% weight bias at the bottom of the esc
32-Bit MCU
13AWG Wires
This product was added to our catalog on November 12, 2023
HADMCL2017, Maclan DRK 160 RS Edition ESC
There are a few options to program the DRK 160 ESC.
Use a ProLink (with cables included in the ProLink, micro USB + OTG cable)
Use a Windows PC and Maclan Panel Software (with cable included in the ESC)
Use an Android mobile device (5.0 OS or higher) and Maclan Smart Link App (with Type C cable, sold separately).
Use an Apple iPhone with Maclan WiFi module (sold separately) with Maclan Smart Link App
Includes:
DRK 160 RS Edition ESC x1, 20cm receiver cable (MCL4243) x1, ESC power switch (MCL4242) x1, USB data cable (MCL4054) x1, Maclan decal x1
Features:
Proprietary 7-Stage launch power control software.
All new profiles designed for NPRC Real Street Class.
Factory pre-soldered 10AWG wires with DRK Super Capacitor module.
Fanless design (You do not need to install the cooling fan).
This item was added to our catalog August 22, 2024
Hobbywing Xerun XD10 Pro Drift Spec Brushless Speed Controller
Features:
Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages.
A separate PRG/FAN port is able to power an external fan to maximize cooling performance or connect an LCD program box or WiFi module to the ESC.
Variable frequency regulation of PWM & brake frequencies allows users to precisely regulate the driving & braking forces (of the motors).
Multiple protections: low-voltage cutoff protection, ESC and motor thermal protection, and fail-safe (throttle signal loss protection), reverse polarity protection (the external standard cap pack will still be damaged if battery reversal occurs).
Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real-time.
Firmware upgrade via Hobbywing multifunction LCD program box (PC only) or OTA Programmer (item sold separately)
Specifications:
Application: 1/10th drift car
Cont./Peak Current: 100A/800A
Input Voltage: 2S LiPo/4-6S NiMH
BEC Output: 5-7.4V Adjustable, Continuous Current of 5A (Switch-mode)
Wires & Connectors: 13AWG 200mm
Programming device: LCD program box, OTA programmer (Available through Firmware update)
Firmware: LCD Program box via USB software (PC only), OTA (iOS / Android)
Size & Weight: 40.7x35.0x32.0mm (w/Fan)
Weight: 95g (w/ wires)
Motor Limit: 2S LiPo/6S NiMH ?8.5T
Includes:
(1) XD10 PRO ESC
(2) Input wires & (3) Output wires (PRE-SOLDERED)
(1) cooling fan
Decals
Bonus parts: heat tubes, double tape, nylon cable zap traps
This product was added to our catalog on May 3, 2023
HW38020422, Hobbywing XR8 SCT Pro ESC Combo w/Xerun 3652SD 6100kv Motor
This is the Hobbywing XeRun XR8 SCT Pro Brushless ESC Combo with Xerun 3652SD 6100kv Motor. This Combo is perfect for 1/8th Buggy Competition, 1/10th STC, Monster Truck, On-road, Buggy, Truggy for High-level Races.
Next generation of Xerun SCT PRO ESC
Super built-in BEC with the peak output current of up to 15A and switchable output voltage of 6V/7.2V;
Advanced electronic switch with the lifespan of over 50000 times of switching on & off;
High-efficiency heat-dissipating system;
Special dynamic timing control program is available when this ESC runs in full-sensored mode*
Innovative coasting function (patent pending)
ESC customization by a LCD program box (Purchased separately) or Wifi Express Module (Purchased separately)
*The full-sensored running mode can only be realized when pairing this ESC with the 1/10 SCT / 1/8th scale new sensored brushless motor by HOBBYWING ESC TECHNICAL SPECS:
Current: 140A/880A
Motor Supported: Sensored/Sensorless Brushless Motor
Applications: 1/8th Buggy Competition, 1/10th STC, Monster Truck, On-road, Buggy, Truggy for High-level Races
Motor Limit with 2S LiPo:
≤6000kv (36XX size)
Motor Limit with 3S LiPo:
≤4000kv (36XX size)
Motor Limit with 4S LiPo:
≤3000kv (36XX size)
Input: 2-4S LiPo; 6-12 Cell NiMh
BEC Output: 6V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC)
Fan (Included): Powered by the stable BEC output voltage of 6V/7.2V
Size/Weight: 54.1(L) x 37.2(W) x 36.1(H w/fan) / 90.5g (W/O Wires)
ESC Programming: LCD Program box, WiFi module enabled
This product was added to our catalog on December 05, 2023
HWI30104002, Hobbywing EZRun Max4 HV 1/5 Scale Sensored Brushless ESC
The Hobbywing EZRun Max4 HV 1/5 Scale Sensored Brushless ESC is the most advanced high voltage ESC on the market. It’s dynamic functionality and 12S specifications meet the needs of power-hungry users. The Max4 HV offers a strong 300A continuous output power with excellent linearity at low speed and offers full-sensored mode operation when combined with a Hobbywing large scale sensored motor.
Features:
Extremely Powerful & Low Temperatures: The internal circuit board of the ESC has been integrated to use copper thermal conduction sink. These are built into high-reliability thermal systems to ensure proper thermal condition while supplying a continuous output current of 300A.
High Reliability & Durability: Max4 HV is the most durable (hardware) and advanced (software) ESC on the market. The ESC is built using the highest quality materials available, to withstand extreme weather and surface conditions. Together with the most advanced software developed by Hobbywing engineers, Hobbywing has created a variety of overload functions to protect the ESC from damage.
Applicable to All Weather Track Conditions: The IP-67 waterproof system guarantees excellent waterproofing and dustproofing protection. The whole power system is able to drive on a variety of surfaces including mud, sand, ice, snow and water without damaging the power unit.
Programming/Upgrading/Data Reading Wirelessly: Using Hobbywing's OTA module and smartphone (with the HOBBYWING HW Link App installed), the user can program parameters, upgrade firmware and relevant data of the ESC.
Real-Time Data & Data Logging: After connecting the OTA module (optional - not included), turn on real-time data recording function to access the operating status.
Capacitor Thermal Protection: Capacitor thermal protection will effectively prevent capacitors from exploding and causing irreversible damage to the ESC due to overload.
Superior Built-in BEC: The built-in BEC can support up to 25A maximum output current. The output voltage is switchable between 6V, 7.4V and 8.4V. This ensures that the ESC is able to support demanding high-torque servos.
Built-In Spark-Proof Design: The built-in spark-proof circuitry helps to prevent damage to the battery connectors, as well as physical injury that could be caused by strong electrical sparks when connecting a "high voltage" battery pack (6-12S).
Advanced & Secured Electronic Switch: The advanced and durable electronic switch features a longer lifespan compared to a standard switch. The dust, dirt, and waterproof switch housing ensures reliability, long life and eliminates unwanted damage. Heavy impact or harsh surfaces will not affect the switch.
Sensor Cable Interface: The MAX4 HV ESC is equipped with a proprietary sensor cable interface. It is high recommended to use the motors from Hobbywing as the waterproof protection level is at the highest level (IP67).
Specifications:
Cont./Peak Current: 300A/2000A
Input Voltage: 6-12S Lipo
BEC Output: 6V / 7.4V / 8.4V adjustable, continuous current 10A (Switch-mode)
Input Wires: Red-8AWG-200mm*1/Black-8AWG-200mm*1
Output Wires: Not Included
Input Connectors: Not Included
Output Connectors: 8.0mm Gold (female)
Fan Size: 50x50x15mm
Fan Voltage Range: 6-8.4V
Size: 125mmx85mmx61.7mm
Weight: 775.4g
KV Rating/T Count: 12S LiPo: KV ? 600KV(70125 Size Motors)
This product was added to our catalog on May 13, 2022
HWI30105000, Hobbywing EZRun MAX6 V3 1/6 Waterproof Brushless ESC (160A, 3-8S)
This is the Hobbywing EZRun MAX6 V3 1/6 Scale Waterproof Brushless ESC. Compatible with 3-8S LiPo power, the MAX6 is a great choice for 1/6 and 1/7 scale vehicles like the Traxxas XO-1, but is also suitable for various 1/8 scale heavy vehicles like the E-REVO and CEN GST-E Monster Trucks. It's the ideal option for high-end aggressively powered builds.
Features:
High Reliability & Durability: Built with the most rugged and high-quality components and coupled with cutting-edge firmware, the EZRun MAX6 is able to deliver unmatched power and performance for even the most hardcore of racing applications, but is also responsive enough to protect itself from damage due to overloading due to physical abuse, overuse or even human error.
Great Flexibility & Versatility: With incredible acceleration capabilities and a rock-solid, stable output, the MAX6 can handle instant full-torque start-ups for wheelies, high-speed racing on straightaways and powering through the bumpiest terrain. The user will have the choice of adjusting the ESC parameters as per his preference and ability.
Applicable for All Weather Conditions: The waterproof and dust-proof design allows the MAX6 to be used in all weather conditions without any issue of damage caused to the ESC from water or dust.
High Voltage Built-in BEC: The MAX6 has adopted the world's first HV built-in BEC with an output current of up to 25Amps and a switchable output voltage of 6-7.4V. The high voltage BEC is designed to handle today's high voltage servos on demand used by large scale vehicles.
Advanced & Secure Electronic Switch: The MAX6 features an electronic switch with a lifespan of over 50,000 on/off cycles, housed in a completely waterproof, dust-proof and shock-resistant design.
Regular Firmware Updates Free of Charge: You can upgrade the MAX6 with the Hobbywing USB LINK software, a multifunction LCD program box and a laptop. Hobbywing updates it's ESC firmware regularly giving you upgraded features more often when available.
Maintenance Free: The ESC, minus the cooling fan, is basically maintenance free. The cooling fan is designed to be shockproof, which in turn will reduce damage brought on by frequent vehicle big jumps and landings on hard surfaces.
Built-in Anti-Spark System: The MAX6 is built wit an internal anti-spark circuitry that protects not only battery connectors from damage but helps to prevent physical injury due to burnt fingers from the inevitable issue of sparking when hooking up the ESC to higher voltage battery packs (5S/6S/7S/8S).
Specifications:
Continuous Current: 160A
Peak Current: 1,050A
Motor Type: Sensorless Brushless Motor
Applications: 1/6th Touring Car, Buggy, Truggy and Truck
Motor Limit: With 6S LiPo/18S NiMH: KV ≤1500 (5892 size motor); With 8S LiPo/24S NiMH: KV ≤1200 (5892 size motor)
LiPo/NiMH Cells: 9-24S NiMH, 3-8S LiPo
BEC Output: 6V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC)
Cooling Fan: Powered by the stable BEC voltage of 6V/7.2V
Connectors: Input End: None, Output End: Female 6.5mm Gold Connectors (pre-soldered onto the PCB of the speed controller)
Size (LxWxH): 70x56x46.5mm
Weight: 240g
Programming Port: FAN /PRG Port
Includes:
(1) Ezrun MAX6 ESC
(3) 10 AWG, 200C Black wires for a brushless motor
(1) Double side tape
(2) Heat shrink tube
(1) Manual
(1) Hobbywing decal
Recommended Hobbywing Programmers:
HWA30502000014: Hobbywing Multifunction LCD Program Box
HWA86020010: Hobbywing Program Box
This product was added to our catalog on May 20, 2021
HWA30108000, Hobbywing Quicrun 10BL60 Sensored Brushless ESC
Features:
High performance but low price- users can own this reliable race-ready ESC at an affordable cost.
Compact size, suitable for various car chassis.
Auto identification system can recognize sensored or sensorless brushless motors automatically.
Smooth operation and plentiful adjustment options. Suitable for most kinds of competitions.
8 steps of timing adjustment greatly increase the output power of the motor and unlock its maximum potential.
Proportional brake with 4 steps of Maximum Brake Force adjustment, 8 steps of Drag Brake Force adjustment and 4 steps of Initial Brake Force adjustment.
9 steps of acceleration (punch) adjustment, from “soft” to “very aggressive” to fit various of cars, tires and tracks.
Multiple protections: Low voltage cut-off protection for LiPo or NiMH battery / Over-heating protection / Throttle signal loss protection / Motor Lock-up protection.
One-button sets the ESC. Easily reset all parameters to factory default settings.
Compatible with optional device ---- the portable Digital LED Program Card, especially convenient for outdoor use.
Specifications:
Applications: 1/10 & 1/12 On-road / Off-road / F1 / Drift car race / Street race for fun / Club racing / STOCK race with 0 timing / Drift car race
Cont./Peak Current/Resistance: 60A/380A/0.0008?
Motor Type Supported: Sensored / Sensorless Brushless Motor
Car Applicable: 1:10 On-road/Off-road/Buggy/Monster
Motor Limit:
2S LiPo or 4-6 cell NiMH: ?8.5T(1/10 On-road), ?13.5T(1/10 Off-road)*
3S LiPo or 8-9 cell NiMH: ?13.5T(1/10 On-road), ?17.5T(1/10 Off-road)*
Battery: 4-9 cell NiMH, 2-3S LiPo
BEC Output: 6V/2A (Linear Mode)
Size: 33mm(L)*28mm(W)*31.5mm(H, with cooling fan)
Weight: 59g (with wires, without cooling Fan)
External Program Port: Available
*NOTE: Indicates the limit value of motor turns when the ESC timing is set to 0. The larger the timing, the more turns the motor needs.
This product was added to our catalog on May 3, 2023
HWA30110000B04, QUICRUN WP 16BL30 COMBO (Bundled) - ESC + QR2435 motor G3 (4500kv) + Programmer
ESC + QR 2435 SL 4500kv G3 motor + Programmer
Waterproof, Sensorless system
ESC
Waterproof and dustproof for all-weather.
One-button (the “SET” button on the ESC) sets the ESC. All parameters easily reset to factory default settings.
Proportional brake with 4 steps of maximum brake force adjustment and 8 steps of drag brake force adjustment.
9 steps of acceleration (/punch) adjustment from “soft” to “Very aggressive” to fit different kinds of models, tires and tracks.
Multiple protections: Low voltage cut-off protection / Over-heating protection / Throttle signal loss protection / Motor lock-up protection.
Motor
Cont./Peak Current: 65Ax4/80Ax4
Input Voltage: 2-3S Lipo/6-9 Cell NiMH
BEC Output: 5V&0.6A
Size: 55x42x6.6mm
Weight: 15g
This product was added to our catalog on May 3, 2023
HWA30110000B05, QUICRUN WP 16BL30 COMBO (Bundled) - ESC + QR2435 motor G3 (6500kv) + Programmer
ESC + Quicrun 2435 brushless motor 6500kv + LED program box
Waterproof, Sensorless system
ESC
Waterproof and dustproof for all-weather.
One-button (the “SET” button on the ESC) sets the ESC. All parameters easily reset to factory default settings.
Proportional brake with 4 steps of maximum brake force adjustment and 8 steps of drag brake force adjustment.
9 steps of acceleration (/punch) adjustment from “soft” to “Very aggressive” to fit different kinds of models, tires and tracks.
Multiple protections: Low voltage cut-off protection / Over-heating protection / Throttle signal loss protection / Motor lock-up protection.
Motor
Cont./Peak Current: 65Ax4/80Ax4
Input Voltage: 2-3S Lipo/6-9 Cell NiMH
BEC Output: 5V&0.6A
Size: 55x42x6.6mm
Weight: 15g
This product was added to our catalog on May 3, 2023
HWA30112003, Hobbywing Xerun XR10 Justock G3 1/10 Sensored Brushless ESC
The Hobbywing XERUN XR10 Justock G3 1/10 Sensored Brushless ESC is the next level in zero timing spec racing. The timing in this ESC has been fixed to a permanent 0° to comply with stock class racing. Package includes one Justock ESC.
Features:
Built-in polarity protection. The XR10 Justock has integrated MOSFET's that if the battery terminals are connected in reverse, the MOSFET will be reverse-biased and will not allow current to flow through the system
Programmable via OTA Bluetooth module or 3in1 program box
Built-in capacitor module eliminates the need for external capacitors and unwanted space
RPM speed limit function supports up to 6 different speed, RPM, selections to meet the needs and demands of various competitions in the world (Set through OTA module or 3in1 box)
Internal ESC timing has been set to 0 degrees and cannot be adjusted for stock racing
Built-in BEC can support a maximum output current of up to 8A. Output voltage can be set between 6V or 7.4V
Calibration or preforming a factory-reset can be achieved by using this SET button. Simple and easy to use
Supports both CCW (counterclockwise) and CW (clockwise) motor directions
Protection functions include: reverse polarity, battery voltage, ESC temperature, motor temperature, signal lost and locked rotor protection
Supports ESC firmware upgrades
User-friendly and convenient for set-up
Specifications:
Continuous Current: 60A
Burst Current: 380A
Battery: 2S Lipo (Only 2S)
Built-in BEC: 6V/7.4V @ 4A(Switch-mode)
ESC programming: Independent programming port
Motor Supported: Sensor and sensorless brushless motor
Motor Limit: 10.5T 3650 Motor
Application: 1/10, 1/12 On-road and Off-road
Cooling Fan: Powered by BEC
Size: 40.9x33.9x32.1mm (LxWxH)
Weight: 75.4g (Including weight of wire)
This product was added to our catalog on May 3, 2023
HWA30112401, Hobbywing Xerun XR10 Pro Stock Spec V4 Sensored Brushless ESC
The Hobbywing Xerun XR10 Pro Stock Spec V4 offers the latest in Hobbywing ESC technology, developed and optimized for stock spec class racing. Recommended for on-road and off-road spec racing, this high quality ESC features a tiny 31.5x25.6x16.1mm footprint, a full aluminum case, and 80 amp current delivery with burst up to 380 amps! Other features include 2S LiPo compatibility, and a 6V/3A switch mode BEC.
Specifications:
Current: Continuous: 80A / Burst: 380A
Battery: 5-7 cells NiMH/NiCd / 2S LiPo
Built-in BEC: 6V@3A (switch mode)
Motor Supported: Sensored and sensorless brushless motors
Suitable Motor: 3650 Motors,1/10 Touring Cars ≥10.5T, 1/10 Buggy≥13.5T
Application: STOCK class of 1/10th Touring Car & Buggy Racing
Cooling Fan: 5V - 7.4V (20x20x8mm)
Wires: 14AWG-200mm
Size: 31.5x25.6x16.1mm
Weight: 28g (without wires and cooling fan)
This product was added to our catalog on May 3, 2023
HWA30112613, Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC (Stealth)
The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC is great for giving the user all the tuning options needed for competitive racing. This Stealth edition is given the Hobbywing FFD (Frameless Fan Design) system for extreme ESC cooling. Get the XR10 G2S and experience true motor control.
Hobbywing FFD:
A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs.
PWM Adjustments:
From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition.
Internal BEC:
The internal BEC is a switching design and provides up to 10A of power. Adjustable from 5-7.4V, this ESC is designed to handle the most power hungry of servos.
NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended.
Features:
32 Bit, M4 microprocessor for ultimate performance
Frameless fan design for extreme cooling
Reverse polarity protection
Precise adjustments to throttle and brake PWM
Optimized programmable parameters
Extended brake force
Drag Brake Acceleration and Softening Function
High output BEC
Specifications:
Wire gauge: 13 AWG Lightweight Ultra-flex
Application: 1/10th Touring car & Buggy racing, 1/10th drift car and F1
Continuous Current: 160A
Peak Current: 1200A
Input Voltage: 2S LiPo / 4-6S Cell NiMH
BEC Output: BEC voltage of 5-7.4V
Programming device: LCD Program Box / OTA Programmer
Firmware: LCD Program box via USB software (PC only) / OTA (iOS / Android)
Size & Weight: 37.5x30.9x32.5mm (with Fan & Fan Shroud)
Weight: 88g (with wires)
Motor spec recommendation:
Touring Car: >4.5T
Buggy: >5.5T
Includes:
(1) Xerun XR10 Pro G2S 160A Sensored Brushless ESC
(1) Cooling Fan
(1) Capacitors
Decals
Accessory package
This product was added to our catalog on December 14, 2023
HWA30112751, Hobbywing Xerun XR10 Pro 1S Stock Spec 1/12 Sensored Brushless ESC
The Hobbywing Xerun XR10 Pro 1S Stock Spec 1/12 Sensored Brushless ESC is super small in size and at 31.6x25.8x16.2mm size, is 20% smaller than the standard version XeRun XR10 Pro 1S. Plus, the light weight (only 23.5g w/o wires) provides more weight margin when adjusting the balance of the chassis.
Features:
Special Design for Stock 1S Class Racing: Reliable hardware combined with powerful software (contains 5 common select-to-use profiles) provides an ideal power solution for 1/12th Stock 1S class racing
Super Internal BEC: The built-in boost BEC with a maximum output of 6A and voltage adjustable between 6V and 7.4V allows users to use various, servos and receivers (without connecting any extra battery).
Adjustable Throttle & Brake PWM Frequencies: The independent and adjustable throttle & brake PWM frequencies guarantee precise and accurate throttle and brake control.
Programming/Upgrading/Data Reading Wirelessly: With Hobbywing's optional "WiFi Express" module (HWA30503000 - not included) and iPhone or an Android phone (with the HOBBYWING WiFi Link software installed), the user can remotely program parameters, upgrade firmware and check relevant data of the ESC without leaving the control stand.
Built-in Electronic Switch: The internal electronic switch with a lifespan of over 50,000 on/off cycles completely solves the problems like stuck reed, rust contact points, and automatic shutdown that conventional mechanical switches often have.
Data-logging Capability: This ESC features the data-logging function which will record the maximum ESC & motor temperatures, the maximum motor RPM, and etc. in real time and allows users to check those data via a LCD program box or WiFi module after each use.
Specifications:
Cont./Peak Current: 80A/380A
Input Voltage: 1S Lipo/3-4 Cell NiMH
BEC Output: 6V/7.4V@3A
Wires: Black-14AWG-200mm
Connectors: No
ESC Programing: LCD Program Box or WiFi Module
Firmware Upgrade Supported: Yes
Size: 31.6x25.8x16.2mm
Weight: 23.5g (w/o Wires)
Applications: Stock 1S class of 1/10th & 1/12th on-road racing.
KV Rating/T Count: ≥10.5T, 3650-size Motor
This product was added to our catalog on May 3, 2023
HWI30120402, HWA30120402, Hobbywing QuicRun Fusion Pro FOC 2-in-1 ESC & Motor System (2300Kv)
The Hobbywing QuicRun Fusion FOC 2300Kv 2-in-1 ESC & Motor System is a unique ground-up design, packed with technology specific for scale trucks and rock crawlers.
Features:
Integrated design of Hobbywing's patent technology: The integrated design of the ESC makes the size similar to a 540 motor, and the overall weight is only 209g. This makes the layout and wiring of the car simpler, while creating a cleaner overall chassis that also leaves more room for an interior.
Intelligent Torque Output & Speed Closed-loop Control for Easy Control: The Fusion system combined with Intelligent Torque output and closed-loop speed control means the power system will maintain the motor’s Torque level and RPM as the vehicle conditions change. Uphill, downhill, under load, the intelligent output torque makes the operation more consistent. Note: If the “RPM/Throttle Matching” is set to “Disabled”, no intelligent torque output & speed closed-loop control, just like the brushed system.
FOC (Field-oriented Control) for Super Linearity & HighTorque & Extreme Mute: The Fusion system adopts FOC driving mode so low speed torque is strong, and it runs smoothly at very low speed. Moreover, the motor is extremely silent when it is running. The driving noise which annoys the driver disappears. It is the best choice for a scale rock crawler.
Waterproof: Applicable to All Weather & Track Conditions: The IP-67 waterproof system has excellent waterproof and dustproof performance. You can easily drive in the mud, sand, ice, snow and water.
High Driving Efficiency for Long Battery Life: FOC offers high efficiency and reduced heat, dramatically extending runtime. Benefitting from a sine wave driving mode, the motor runs silently and softly.
Professional Drag Brake Adjustments & Super Parking Capacity: 8 levels of drag brake force and 9 settings of drag brake rate allow a high level of tuning for different conditions and driver preference. The maximum drag brake force is about twice that of an ordinary brushless system of the same size, providing super strong parking capacity on a steep slope.
Advanced and Secure Electronic Switch: Compared to standard on/off switches, the dust, dirt, and waterproof electronic switch housing ensures a long reliable life for your power system, and will not suffer from the problems that will damage a mechanical switch.
Specifications:
Motor Kv: 2300Kv
Continuous Current: 60A
Shaft Diameter: 3.175mm
Peak Current: 200A
Input Voltage: 2-3S LiPo/6-9 Cell NiMH
BEC Output: 6V/7.4V adjustable, 4A continuous (switch mode)
Input Wires: 14awg, 330mm long
Input Connectors: XT60 (factory installed)
Port Programming: Independent programing interface (switch position)
Size: 37x58mm
Weight: 209g w/wires
Includes:
(1) FOC motor w/ built-in ESC & Factory installed XT60 plug
This product was added to our catalog on June 1, 2022
HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T)
The Hobbywing Quicrun 3650 G2 Sensored Brushless Motor is a high efficiency option, creating good power, and keeping temps low. Ideal for 1/10th, 1/12th On-road (Race or drift Touring cars, F1, M vehicles and etc.) & Off-road (Buggies/2WD SCTs & Trucks) STOCK/SPORT Class Competitions (About Motors' T counts, please refer to rules regulated by race organizers), Beginners for practice, and Rock Crawlers (applicable to 21.5T,25.5T motors) applications.
Features:
Built-in Hall sensor brings drivers an amazing sense of control.
Top-quality components: heat-resistant magnet, heat-resistant wires and name-brand bearings.
Dustproof design where motor leads exit.
Features a gold-plated lockable connector which can be fastened by screws, eliminating the possibility of losing connections.
Detachable structure is easy to clean and maintain, greatly prolonging the service life of the motor.
Specifications:
Turn: 21.5T
Kv: 1800Kv
LiPo: 2-3S
Shaft Diameter: 3.175mm
Resistance: 0.0747 ohm
No Load Current: 1.3A
Max Output Power: 95W
Max Output Current: 28A
Weight: 186g
This product was added to our catalog on May 3, 2023
HWI38010801, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/4985SL (1650kV)
The Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo includes the 4985SL 1/7 scale, 1650kV motor and is a great option for high-end, aggressively powered 3S - 6S builds.
Specifications:
Motor:
Model: 4985SL-1650KV
Pole: 4
KV (No-load): 1650KV
Resistance: 0.0053 Ω
Current (No-load): 5.4 A
Max. Output Power: 5700 W
Current at the point of M.O.P: 160 A
Motor Diamter: 49mm
Motor Length: 86.5mm
Shaft Diameter: 5.0mm
Shaft Length: 21.5mm
LiPo Cells: 3-6
Weight: 587g (20.71oz)
Applications: 1/6th & 1/7th RC Vehicles
ESC:
Continuous Current: 160A Peak Current:
Peak Current:
Peak Current: 1,050A
Motor Type: Sensorless Brushless Motor
Applications: 1/6th Touring Car, Buggy, Truggy and Truck
Motor Limit: With 6S LiPo/18S NiMH: KV ≤1500 (5892 size motor); With 8S LiPo/24S NiMH: KV ≤1200 (5892 size motor)
LiPo/NiMH Cells: 9-24S NiMH, 3-8S LiPo
BEC Output: 6V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC)
Cooling Fan: Powered by the stable BEC voltage of 6V/7.2V
Connectors: Input End: None, Output End: Female 6.5mm Gold Connectors (pre-soldered onto the PCB of the speed controller)
Size (LxWxH): 70x56x46.5mm
Weight: 240g
Programming Port: FAN /PRG Port
This product was added to our catalog on April 21, 2021
HWI38010802, Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo w/5687SL (1100kV)
The Hobbywing EZRun MAX6 V3 Sensorless Brushless ESC & Motor Combo includes the 5687SL 1/5 scale, 1150kV motor and is a great option for high-end, aggressively powered, large scale 8S builds.
Specifications:
Motor:
Model: 5687SL-1100KV
Pole: 4
KV (No-load): 1100KV
Resistance: 0.0041 Ω
Current (No-load): 4.1 A
Max Output Power: 5800 W
Current at the point of M.O.P: 200 A
Motor Diameter: 56mm
Motor Length: 87mm
Shaft Diameter: 8.0mm
Shaft Length: 31.0mm
LiPo Cells: 3-8
Weight: 916g (32.21oz)
Applicable: 1/5th RC Vehicles Truck/Dragster
ESC:
Continuous Current: 160A Peak Current:
Peak Current:
Peak Current: 1,050A
Motor Type: Sensorless Brushless Motor
Applications: 1/6th Touring Car, Buggy, Truggy and Truck
Motor Limit: With 6S LiPo/18S NiMH: KV ≤1500 (5892 size motor); With 8S LiPo/24S NiMH: KV ≤1200 (5892 size motor)
LiPo/NiMH Cells: 9-24S NiMH, 3-8S LiPo
BEC Output: 6V/7.2V Switchable, Continuous Current of 6A (Switch-mode BEC)
Cooling Fan: Powered by the stable BEC voltage of 6V/7.2V
Connectors: Input End: None, Output End: Female 6.5mm Gold Connectors (pre-soldered onto the PCB of the speed controller)
Size (LxWxH): 70x56x46.5mm
Weight: 240g
Programming Port: FAN /PRG Port
This product was added to our catalog on April 25, 2021
HWA38020322, Hobbywing XR10 Justock G3 Sensored Brushless ESC/SD G2.1 Motor Combo (21.5T)
The Hobbywing XR10 Justock G3 Sensored Brushless ESC/SD G2.1 Motor Combo has been designed with fixed, 0°, timing for spec class racing. The included SD G2.1 motor is an ideal stock motor for both 1/10 and 1/12 on and off-road racing. These two components paired together make for an ideal choice for beginners and experts alike.Features:
ESC:
Built-in polarity protection. The XR10 Justock has integrated MOSFET's that if the battery terminals are connected in reverse, the MOSFET will be reverse-biased and will not allow current to flow through the system
Programmable via OTA Bluetooth module or 3in1 program box
Built-in capacitor module eliminates the need for external capacitors and unwanted space
RPM speed limit function supports up to 6 different speed, RPM, selections to meet the needs and demands of various competitions in the world (Set through OTA module or 3in1 box)
Internal ESC timing has been set to 0 degrees and cannot be adjusted for stock racing
Built-in BEC can support a maximum output current of up to 8A. Output voltage can be set between 6V or 7.4V
Calibration or preforming a factory-reset can be achieved by using this SET button. Simple and easy to use
Supports both CCW (counterclockwise) and CW (clockwise) motor directions
Protection functions include: reverse polarity, battery voltage, ESC temperature, motor temperature, signal lost and locked rotor protection
Supports ESC firmware upgrades
User-friendly and convenient for set-up
Motor:
Use of a heat-resistant magnet attached aluminum case and double insulated windings, high precision bearings, and rotor with a strong structure guarantees outstanding performance and super durability
Built-in Hall sensor non-adjustable end bell combined with a high precision and balanced rotor guarantees the user a smooth and linear power on demand
Silicon O-ring seal fitted between the end bell and stator helps to conduct inner heat to the motor case and prevent dust from entering the HALL sensor
Detachable structure design for daily cleaning and maintenance can effectively prolong the service life of this Justock motor and improve its operating efficiency
This Justock motor is applicable to various 1/10th, 1/12th on-road & off-road vehicles. It can be an ideal choice for Stock or Sport class races but can also be a nice choice for newbies for practice
The motor design is in compliance with IFMAR, and ROAR specifications
Specifications:
ESC:
Continuous Current: 60A
Burst Current: 380A
Battery: 2S Lipo (Only 2S)
Built-in BEC: 6V/7.4V @ 4A(Switch-mode)
ESC programming: Independent programming port
Motor Supported: Sensor and sensorless brushless motor
Motor Limit: 10.5T, or greater, 3650 Motor
Application: 1/10, 1/12 On-road and Off-road
Cooling Fan: Powered by BEC
Size: 40.9x33.9x32.1mm (LxWxH)
Weight: 75.4g (Including weight of wire)
Motor:
Scale: 1/10, 1/12
Brushless: Yes
Sensored: Yes
Pole Count: 2
KV Rating: 2050
LiPo Cells: 2-3S
No-Load Current(A): 3
Outer Diameter: 35.9mm (1.413")
Length: 52.5mm (2.067")
Shaft Diameter: 3.17mm (0.125")
Weight: 175g (6.17oz)
Timing: Fixed
Includes:
(1) Justock G3 ESC
(1) Justock 21.5t G2.1 brushless motor
(1) 5V cooling fan
(1) Sensor cable
This product was added to our catalog on May 3, 2023
HWA38020323, Hobbywing XR10 Justock G3 Sensored Brushless ESC/SD G2.1 Motor Combo (25.5T)
The Hobbywing XR10 Justock G3 Sensored Brushless ESC/SD G2.1 Motor Combo has been designed with fixed, 0°, timing for spec class racing. The included SD G2.1 25.5T motor is an ideal choice for vintage trans am, formula and other on-road racing classes. These two components paired together make for an ideal choice for beginners and experts alike. Features:
ESC:
Built-in polarity protection. The XR10 Justock has integrated MOSFET's that if the battery terminals are connected in reverse, the MOSFET will be reverse-biased and will not allow current to flow through the system
Programmable via OTA Wireless module or 3in1 program box
Built-in capacitor module eliminates the need for external capacitors and unwanted space
RPM speed limit function supports up to 6 different speed, RPM, selections to meet the needs and demands of various competitions in the world (Set through OTA module or 3in1 box)
Internal ESC timing has been set to 0 degrees and cannot be adjusted for stock racing
Built-in BEC can support a maximum output current of up to 8A. Output voltage can be set between 6V or 7.4V
Calibration or preforming a factory-reset can be achieved by using this SET button. Simple and easy to use
Supports both CCW (counterclockwise) and CW (clockwise) motor directions
Protection functions include: reverse polarity, battery voltage, ESC temperature, motor temperature, signal lost and locked rotor protection
Supports ESC firmware upgrades
User-friendly and convenient for set-up
Motor:
Use of a heat-resistant magnet attached aluminum case and double insulated windings, high precision bearings, and rotor with a strong structure guarantees outstanding performance and super durability
Built-in Hall sensor non-adjustable end bell combined with a high precision and balanced rotor guarantees the user a smooth and linear power on demand
Silicon O-ring seal fitted between the end bell and stator helps to conduct inner heat to the motor case and prevent dust from entering the HALL sensor
Detachable structure design for daily cleaning and maintenance can effectively prolong the service life of this Justock motor and improve its operating efficiency
This Justock motor is applicable to various 1/10th, 1/12th on-road Stock Spec Racing, ICC, IOCC, USVTA, TOUR, Oval racing. It can be an ideal choice for Stock or Sport class races but can also be a nice choice for newbies for practice
The motor design is in compliance with IFMAR, and ROAR specifications
Specifications:
ESC:
Continuous Current: 60A
Burst Current: 380A
Battery: 2S Lipo (Only 2S)
Built-in BEC: 6V/7.4V @ 4A(Switch-mode)
ESC programming: Independent programming port
Motor Supported: Sensor and sensorless brushless motor
Motor Limit: 10.5T, or greater, 3650 Motor
Application: 1/10, 1/12 On-road and Off-road
Cooling Fan: Powered by BEC
Size: 40.9x33.9x32.1mm (LxWxH)
Weight: 75.4g (Including weight of wire)
Motor:
Scale: 1/10, 1/12
Brushless: Yes
Sensored: Yes
Pole Count: 2
KV Rating: 1600
LiPo Cells: 2-3S
No-Load Current(A): 2.8
Outer Diameter: 35.9mm (1.413")
Length: 52.5mm (2.067")
Shaft Diameter: 3.17mm (0.125")
Weight: 173g (6.10oz)
Timing: Fixed
Includes:
(1) Justock G3 ESC
(1) Justock 25.5t G2.1 brushless motor
(1) 5V cooling fan
(1) Sensor cable
This product was added to our catalog on October 20, 2023
HWA38020334, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (13.5T)
This is the Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo. Using the precise control of the XR10 Pro G2S combined with a powerful V10 G4 motor gives the user a dominant combo!
XR10 Pro G2S 160A ESC:
The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC offers all the tuning options needed for competitive racing while giving reliable performance on the track. Helping to keep this ESC reliable is the Frameless Fan Design (FFD) fan system. A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. At the racetrack ESC adjustments can be crucial. The XR10 Pro G2S is packed with features such as several PWM adjustments. From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition.V10 G4 Motor:
The V10 G4 Competition Stock Brushless Motor has been greatly optimized to provide maximum torque and increased power. With a lower internal resistance, this motor is more efficient and runs cooler when compared to the G3R motors. To further increase performance the motor adopts a fully exposed stator core allowing more airflow over the stator. The motor also features a high-precision endbell plate to improve consistency and structural stability. Dual sensor ports can be found allowing for different wiring setups.NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended.
Features:
ESC:
Upgraded 32-bit M4 microprocessor with more powerful processing capability guarantees stable control and rapid response. (Industry's highest 32-bit microprocessor, increased processing speed by X4)
Peak current up to 1200A. (This is not a typo)
Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages.
Variable frequency regulation of PWM & amp; brake frequencies allows users to precisely regulate the driving; braking forces (of the motors).
Expanded range of the max. brake force brings in the active brake ranges from 101% to 150%.
Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency.
10 select-to-use profiles applicable to all 1/10th RC car racing.
Internal electronic key switch for long service life, high reliability; and the external switch port for connecting an external switch (included in the product box) is applicable to different situations.
Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or WiFi module to the ESC.
With the Updated WIFI express module (purchase separately), users are able to program parameters, upgrade firmware and check relevant data during the event using either the iPhone or Android devices.
Switchable motor direction (CCW/CW) for various chassis.
Multiple protections comes in standard
Low-voltage cutoff protection
ESC and motor thermal protection
Fail safe (throttle signal loss protection)
Reverse polarity protection
Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real time.
Firmware upgrade via Hobbywing multi-function LCD program box or WiFi Express (item sold separately).
Motor:
Specially designed for high-level racing.
Lightweight: The G4 Modified & Stock motors only weigh 161g & 132g respectively.
The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor.
The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G4 Stock motors (10.5T~25.5T), the timing is adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees.
The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts.
The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors effectively keep sand or dirt from getting inside and damaging the motor(s).
The use of high-performance stator core, heat (200°C) resistant wire, heat (200°C) resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current endurance guarantees outstanding performance and super durability.
Specifications:
ESC:
Cont./Peak Current: 160A / Burst: 1200A
Battery: 5-6 cells NiMH/NiCd / 2S LiPo
BEC Output: 5V-7.4V
Motor Supported: Sensored and sensorless brushless motors
Suitable Motor: 3650 Motors 1/10th Touring Car: 4.5T, 1/10th Buggy: 5.5T
Application: Brushless motor system for 1/10th, 1/12th Touring Cars & Buggies Racing, Splash proof
Wires: Standard 13AWG 200mm
Size: 37.5X30.9X32.5mm
Weight: 90g (with wires)
Motor:
kV Rating: 3950kV
Cell Count: 2-3S
No-Load Current: 4.5A
Outer Diameter: 35.8mm
Length: 51.4mm
Shaft Diameter: 3.175
Weight: 149g
Front Bearing: 9x4x4mm
Rear Bearing: 8x3x4mm
Adjustable Timing: 30-60°
Applications: 1/10th Stock Class Racing
This product was added to our catalog on July 20, 2022
HWA38020336, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (21.5T)
This is the Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo. Using the precise control of the XR10 Pro G2S combined with a powerful V10 G4 motor gives the user a dominant combo!
XR10 Pro G2S 160A ESC:
The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC offers all the tuning options needed for competitive racing while giving reliable performance on the track. Helping to keep this ESC reliable is the Frameless Fan Design (FFD) fan system. A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. At the racetrack ESC adjustments can be crucial. The XR10 Pro G2S is packed with features such as several PWM adjustments. From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition.
V10 G4 Motor:
The V10 G4 Competition Stock Brushless Motor has been greatly optimized to provide maximum torque and increased power. With a lower internal resistance, this motor is more efficient and runs cooler when compared to the G3R motors. To further increase performance the motor adopts a fully exposed stator core allowing more airflow over the stator. The motor also features a high-precision endbell plate to improve consistency and structural stability. Dual sensor ports can be found allowing for different wiring setups.
NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended.
Features:
ESC:
Upgraded 32-bit M4 microprocessor with more powerful processing capability guarantees stable control and rapid response. (Industry's highest 32-bit microprocessor, increased processing speed by X4)
Peak current up to 1200A. (This is not a typo)
Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages.
Variable frequency regulation of PWM & amp; brake frequencies allows users to precisely regulate the driving; braking forces (of the motors).
Expanded range of the max. brake force brings in the active brake ranges from 101% to 150%.
Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency.
10 select-to-use profiles applicable to all 1/10th RC car racing.
Internal electronic key switch for long service life, high reliability; and the external switch port for connecting an external switch (included in the product box) is applicable to different situations.
Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or WiFi module to the ESC.
With the Updated WIFI express module (purchase separately), users are able to program parameters, upgrade firmware and check relevant data during the event using either the iPhone or Android devices.
Switchable motor direction (CCW/CW) for various chassis.
Multiple protections comes in standard
Low-voltage cutoff protection
ESC and motor thermal protection
Fail safe (throttle signal loss protection)
Reverse polarity protection
Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real time.
Firmware upgrade via Hobbywing multi-function LCD program box or WiFi Express (item sold separately).
Motor:
Specially designed for high-level racing.
Lightweight: The G4 Modified & Stock motors only weigh 161g & 132g respectively.
The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor.
The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G4 Stock motors (10.5T~25.5T), the timing is adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees.
The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts.
The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors effectively keep sand or dirt from getting inside and damaging the motor(s).
The use of high-performance stator core, heat (200°C) resistant wire, heat (200°C) resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current endurance guarantees outstanding performance and super durability.
Specifications:
ESC:
Cont./Peak Current: 160A / Burst: 1200A
Battery: 5-6 cells NiMH/NiCd / 2S LiPo
BEC Output: 5V-7.4V
Motor Supported: Sensored and sensorless brushless motors
Suitable Motor: 3650 Motors 1/10th Touring Car: 4.5T, 1/10th Buggy: 5.5T
Application: Brushless motor system for 1/10th, 1/12th Touring Cars & Buggies Racing, Splash proof
Wires: Standard 13AWG 200mm
Size: 37.5X30.9X32.5mm
Weight: 90g (with wires)
Motor:
kV Rating: 2500kV
Cell Count: 2-3S
No-Load Current: 3.0A
Outer Diameter: 35.8mm
Length: 51.4mm
Shaft Diameter: 3.175
Weight: 148g
Front Bearing: 9x4x4mm
Rear Bearing: 8x3x4mm
Adjustable Timing: 30-60°
Applications: 1/10th Stock Class Racing
This product was added to our catalog on May 3, 2023
HWA38030208, Hobbywing QuicRun 10BL120 G2 Sensorless Brushless ESC/3652SL Motor Combo (4000kV)
The Quicrun 10BL120 G2 Sensorless Brushless ESC and Motor Combo have been designed to deliver extreme power and reliability with a more efficient dust-proof motor and IP-67 waterproof rated ESC. The 10BL's built in capacitor improves on the brownout protection, efficiency, and thermal protection. This combo will be a great option for a wide range of RC models.
Features:
G2 QuicRun 10BL120
Intelligent freewheeling technology
Extreme performance
Powerful built-in BEC
Efficient cooling system
Capacitor Thermal Protection
Built-in capacitor
IP-67 waterproof Rating
G2 QuicRun 3660SL
High efficiency for more power with lower temperatures!
4-pole rotor design for more torque with strong explosive force.
Compared with the previous generation of motors, the output power and efficiency are increased by more than 10%, and the motor temperature is effectively reduced under the same load.
0.2mm thick silicon steel laminations, high strength explosion-proof rotor, high-temperature resistant coil, and imported high-precision and high-quality bearings make the motor super durable.
Specifications:
ESC:
Scale: 1/10th
Brushed/Brushless: Brushless
Sensored/Sensorless: Sensorless
Waterproof: IP-67
Current:
Continuous: 120A
Peak: 760A
Input Voltage: 2-4S LiPo
BEC Output: 6V/7.4V @ 5A
Output Connectors: 4.0mm Bullets
Dimensions: 2.07x1.56x1.50" (52.8x39.8x38.2mm)
Weight: 4.19oz (119g)
Motor:
Input Voltage: 2S-3S LiPo
KV: 4000kV
Pole: 4
Motor Diameter: 1.42" (36mm)
Motor Length: 2.05" (52mm)
Shaft Diameter: 0.13." (3.175mm)
Shaft Length: 0.59" (15mm)
Front Bearing size: D13*D5*T5
Rear Bearing size: D13*D5*T4
Weight: 224g
Includes:
(1) QuicRun 10BL120 G2 1/10 Sensorless Brushless ESC
(1) QuicRun 3652SL G2 Sensorless Brushless Motor (4000kV)
This product was added to our catalog on May 3, 2023
HWI30402550, Hobbywing EZRUN 5687SL 4-Pole 1/5 Scale Sensorless Brushless Motor (1100kV)
Specifications:
Model: 5687SL-1100KV
Pole: 4
KV (No-load): 1100KV
Resistance: 0.0041 Ω
Current (No-load): 4.1 A
Max Output Power: 5800 W
Current at the point of M.O.P: 200 A
Motor Diameter: 56mm
Motor Length: 87mm
Shaft Diameter: 8.0mm
Shaft Length: 31.0mm
LiPo Cells: 3-8
Weight: 916g (32.21oz)
Applicable: 1/5th RC Vehicles Truck/Dragster
Suitable ESC: Ezrun MAX5 or MAX6 ESC
This product was added to our catalog on April 25, 2019
HWI30404307, HobbyWing Quicrun 3650 G2 Sensored Brushless Motor (21.5T)
The Hobbywing Quicrun 3650 G2 Sensored Brushless Motor is a high efficiency option, creating good power, and keeping temps low. Ideal for 1/10th, 1/12th On-road (Race or drift Touring cars, F1, M vehicles and etc.) & Off-road (Buggies/2WD SCTs & Trucks) STOCK/SPORT Class Competitions (About Motors' T counts, please refer to rules regulated by race organizers), Beginners for practice, and Rock Crawlers (applicable to 21.5T,25.5T motors) applications.
Features:
Built-in Hall sensor brings drivers an amazing sense of control.
Top-quality components: heat-resistant magnet, heat-resistant wires and name-brand bearings.
Dustproof design where motor leads exit.
Features a gold-plated lockable connector which can be fastened by screws, eliminating the possibility of losing connections.
Detachable structure is easy to clean and maintain, greatly prolonging the service life of the motor.
Specifications:
Turn: 21.5T
Kv: 1800Kv
LiPo: 2-3S
Shaft Diameter: 3.175mm
Resistance: 0.0747 ohm
No Load Current: 1.3A
Max Output Power: 95W
Max Output Current: 28A
Weight: 186g
This product was added to our catalog on April 21, 2024
KYO32891, Kyosho MR-04 EVO2 Mini-Z N-MM2 Brushless Chassis Set (5600kV)
Performance Mini-Z Chassis Roller & Brushless Motor
The MR-04EVO2 Mini-Z N-MM2 Brushless Chassis Set (5600kV) represents a significant leap forward in the top-tier MINI-Z series, offering a full model upgrade that pushes the boundaries of performance. Retaining the excellent MR-03 layout while introducing key enhancements, the MR-04EVO2 chassis achieves unparalleled performance improvements. The lower center of gravity (CG) resulting from the lower mounting of AAA batteries enhances stability through corners and elevates both speed and control. This thoughtful chassis design, coupled with the Sensored brushless motor, provides a total balance that takes performance to a higher level, making it a formidable competitor in the high-performance competition mini R/C car category.
Quality is evident in the meticulous design and engineering of the MR-04EVO2 chassis. The front suspension improvements, including an updated kingpin-integrated knuckle for enhanced camber stability, showcase a commitment to optimizing every detail. The geometric revisions of the caster and trail contribute to more linear maneuverability, allowing drivers precise control over their vehicles. The inclusion of a ball differential as standard further refines the driving experience, optimizing rotational differences between left and right rear wheels during turns and providing moderate slip action for improved traction. The silver clear anodized finish on aluminum parts not only contributes to durability but also adds a stylish touch that matches the chassis's exceptional performance.
What makes the MR-04EVO2 truly special is its adaptability and customization options. The chassis supports both narrow and wide tread settings, allowing enthusiasts to tailor their setup according to body type. Adjustable wheelbase adds another layer of customization, providing flexibility in chassis settings. The included brushless motor, Kyosho Speed House XSpeed 56 (5600kV) ensures the delivery of powerful, smooth and efficient performance! Taking the MR-04EVO2 to another level of dominance in the world of high-performance mini competition R/C cars, solidifying its position as one of the best of the best!
NOTE: This is an assembled chassis that still requires additional items to run. See needed to complete list below for a list of items required to complete the model.
Features:
Powerful Kyosho Speed House XSpeed 56 (5600kV) brushless motor
Lower CG design with lower battery mounting positions
Significant performance improvements
Updated kingpin-integrated knuckle to further improve camber stability
Adjustable wheelbase and tread settings
Adjustable wheelbase
Ball differential included as standard
Ball bearings have been changed to 3mm internal diameter for lower rotational resistance
Geometric revision of caster and trail
Improved linear maneuverability
Specifications:
Scale: 1/27
Length: 124.5mm
Width: 72-76mm
Height: 31mm
Wheelbase: 98.0mm (LL)
Weight: 135.5g
Front Tread: 58.5 / 65.0mm
Rear Tread: 61.5 / 65.0mm
Gear Ratio: 7.3 / 6.3 / 5.5 / 4.9 1
Motor: XSpeed 56 (5600kV)
Includes:
(1) MR-04EVO2 Mini-Z N-MM2 Brushless Chassis Set w/(5600kV) Motor
(1) Electronic speed controller (ESC)
6T / 7T / 8T / 9T Pinion gears
Pinion gear tool
Wheel wrench
Spare wheel nuts
Needed to Complete:
(1) 2-Channel Transmitter/Receiver system
(4) AAA Batteries for Chassis
(1) Body
(4) Tires
(4) Wheels
This product was added to our catalog November 22, 2024
KYO34482T1, Kyosho EP Fazer Mk2 FZ02-R 1971 Datsun 240Z Rally ReadySet (Red)
Experience the thrill and nostalgia of the EP Fazer Mk2 FZ02-R 1971 Datsun 240Z Rally ReadySet by Kyosho. Whether you're a beginner or a seasoned enthusiast, this rally weapon offers exceptional performance and handling. With a shaft-type 4WD system and specially designed suspension, it delivers superior traction control and reliability, perfect for conquering both on and off-road terrain.
About the Fazer Mk2 FZ02-R
Ultra-Scale Body Design
This kit includes a meticulously crafted 1971 Datsun 240Z Rally body, faithfully reproducing the iconic rally specifications of the Nissan sports car. Crafted by Kyosho with precision, this body captures the essence of rally driving, complete with injection-molded details and the option to attach LED light units for added realism.
Rally-Optimized Features
Engineered specifically for rally driving, the Fazer Mk2 FZ02-R chassis boasts features like big bore oil shocks, shock stays, and steering hub arms designed to tackle harsh terrains with ease. The chassis cover protects sensitive R/C components from dirt and elements, ensuring durability and reliability even in challenging conditions.
Complete ReadySet Package
The ReadySet includes a fully assembled chassis and body, along with a Syncro KT-231P+ transmitter for convenient setup and control. Additionally, the kit comes with essential tools and setting change parts, making it easy to customize and maintain your rally machine. Just add batteries for the transmitter and chassis, and you're ready to hit the track and unleash the rally beast within.
Includes:
(1) Kyosho Fazer Mk2 FZ02-R Chassis
(1) Pre-Painted 1971 Datsun 240Z Rally
(1) 2.4GHz Transmitter & Receiver
Product Manual
Needed To Complete:
(1) 2S (7.4V) LiPo Battery with T-Style connector
(1) Compatible LiPo Battery Charger
(4) AA Batteries for Transmitter
Misc. Tools
Specifications:
Scale
1:10
Drive
4WD
Power Source
Electric
Length
18.62in (473mm)
Wheelbase
10.24in (260mm)
Width
7.64in (194mm)
Height
5.60in (142mm)
Weight
58.2oz (1650g)
Completion Level
Ready-To-Run
This item was added to our catalog on November 27, 2024
KYO34492T1C, Kyosho EP Fazer Mk2 FZ02L VE 1970 Dodge Charger Supercharged ReadySet (Grey) w/Syncro KT-231P+ Radio
Kyosho Fazer Mk2 FZ02L VE Brushless Touring Car with Supercharged 1970 Dodge Charger Body
The Kyosho EP Fazer Mk2 FZ02L VE 1970 Dodge Charger Supercharged ReadySet is a brushless chassis that has a classic muscle car look. The combination of a beautifully reproduced body with the FAZER series chassis can’t be beaten. This Charger body features a scale supercharger and molded light buckets for optional LED's (not included). To complete the look, Kyosho included functional flip headlight covers that can actuate by removing a screw from the headlight assembly.
Featuring front & rear gear differentials, oil shocks and full ball bearing specs, the high durability and impact resistance allows drivers to unleash the full potential of the chassis. Brake disc wheel hubs with two different offsets (0mm, +5mm) provide compatibility with 190mm and 200mm width body styles and allows the wheelbase to be adjusted to 260mm by replacing some parts (not included) for compatibility with other 1/10 scale body styles, in addition to the included body. The symmetrical chassis design synergizes excellent front-rear balance through the suspension with responsive control, regardless of the power source. The Ready Set package comes fully assembled and requires only charger and battery for the chassis, and batteries for the transmitter to start driving.
Features:
“Ultra Scale Body” replicates the fine details of the actual body of the car.
Shaft drive full-time 4WD touring chassis (FZ02)
Factory-assembled Readyset package only requires 4 x AA alkaline batteries for the transmitter, and battery with charger for the chassis
Equipped with 2-bevel grease-filled gear diffs on front and rear
Large size dog bones and cup joints realize superior reliability and durability
Belt mounting battery compartment allows various battery types to be used
Full ball bearings that reduce drive loss equipped throughout the drive system
Includes completely finished body with color scheme and decals applied
Sealed differential and transmission deliver reliable performance, even on dusty parking lot surfaces
Performance can be further enhanced by installing various optional parts
Specifications:
Length: 507mm
Width: 195mm
Body Width: 210mm
Height: 128mm
Chassis Height: 15mm
Wheelbase: 274mm
Tread (F/R): 167mm
Tires (F/R): 64×27.7mm
Gear Ratio: 6.54:1
Weight: 1680g
Includes:
Completed chassis with R/C radio installed
Factory assembled body complete with color scheme
Syncro KT-231P+ transmitter
Hexagonal wrench
Spanner
Needed to Complete:
(4) AA batteries for transmitter
7.2-7.4V Battery for chassis
Charger for battery for chassis
Tools
This product was added to our catalog on May 9, 2022
Kyosho Fazer Mk2 FZ02 VE 69 Camaro Z/28 RS Supercharged ReadySet (Tuxedo Black) w/Syncro KT-231P+
The Kyosho Fazer Mk2 FZ02 VE 1969 Camaro Z/28 RS Supercharged ReadySet was created for the pure enjoyment of R/C car driving. The combination of a beautifully reproduced body with the FAZER series chassis can’t be beaten. Kyosho has taken its standard touring car chassis and given it a full model makeover that has evolved performance to a new level. A simplified design with fewer parts has improved maintenance efficiency and reduced weight while core strength and rigidity has been increased through materials with ribbing and stiffeners on front and rear. In addition, the symmetrical chassis design synergizes excellent front-rear balance through the suspension with responsive control, regardless of the power source.
Featuring front & rear gear differentials, oil shocks and full ball bearing specs, the high durability and impact resistance allows drivers to unleash the full potential of the chassis. Brake disc wheel hubs with two different offsets (0mm, +5mm) provide compatibility with 190mm and 200mm width body styles and allows the wheelbase to be adjusted to 260mm by replacing some parts (not included) for compatibility with other 1/10 scale body styles, in addition to the included body. The Readyset package comes fully assembled and requires only charger and battery for the chassis, and batteries for the transmitter to start driving.
Features:
“Ultra Scale Body” replicates the fine details of the actual body of the car.
Shaft drive full-time 4WD touring chassis (FZ02)
Factory-assembled Readyset package only requires 4 x AA alkaline batteries for the transmitter, and battery with charger for the chassis
Equipped with 2-bevel grease-filled gear diffs on front and rear
Large size dog bones and cup joints realize superior reliability and durability
Belt mounting battery compartment allows various battery types to be used
Full ball bearings that reduce drive loss equipped throughout the drive system
Features KS202W waterproof steering servo
Includes completely finished body with color scheme and decals applied
Sealed differential and transmission deliver reliable performance, even on dusty parking lot surfaces
Performance can be further enhanced by installing various optional parts
Specifications:
Length: 461mm
Width: 210mm
Height: 138mm
Wheelbase: 260mm
Tread (F/R): F:167mm/R:167mm
Tires (F/R): F:64×27.7mm/R:64×27.7mm
Gear Ratio: 6.54:1
Weight: 1650g (approx.)
R/C system: Syncro KT-231P+
Motor: TORX10E
Includes:
Completed chassis with R/C radio installed
Factory assembled body complete with color scheme
Syncro KT-231P+ transmitter
Hexagonal wrench
Spanner
Needed to Complete:
(4) AA batteries for transmitter
7.2-7.4V Battery for chassis
Charger for battery
Tools
This product was added to our catalog on November 30, 2022
KYO34494T1, Fazer Mk2 VE 1970 Chevelle Supercharged Dark Blue
This V8 powered American muscle car from the 1970s is recreated by using Kyosho's original supercharger and mufflers on both sides. The elegant body lines, rugged engine head and sparkling muffler create a perfect match.
The motor has been upgraded to the powerful TORX10E brushless motor, increasing the maximum speed to approximately 65km/h (40mp/h). The speed controller has also been upgraded with the new BRAINZ 10 V2. To handle the increased power of the motor, the pinion gear has been sintered (hardened) and the aluminum HD center shaft is factory installed.
Includes:
RTR - Factory-assembled chassis with R/C unit installed
Painted/Decaled/Assembled body
Synchro KT-231P+ transmitter
Optional Light Buckets (Requires installation, led set sold separately)
Hex wrench
Spanner
Required to Complete:
4 AA batteries for transmitter
Compatible Ni-MH (6-9s) or LiPo (2-3s) battery
Charger for chosen battery
Features:
Body has supercharger and mufflers preinstalled
Sintered (hardened) pinion gear
Aluminum Center Shaft
LCG Chassis w/ integrated gearbox
Sealed Motor Case
TORX10E/BRAINZ 10 V2 Motor/ESC Combo
Supercharger can be manually opened and closed
Specifications:
4WD - Shaft Driven
Water-Resistant Electronics
This item was added to our catalog on April 5, 2024
ONI4605, Onisiki 120 Amp Brushless Drift Electronic Speed Controller (Limited Edition)
Onisiki 120 Amp Brushless Drift Electronic Speed Controller. This ESC is a great option for RC drift applications due to its smooth throttle response and adjustable timing. The ESC is capable of 120A to keep performance consistent through the run. Onisiki gave this ESC their signature markings to best match the other available accessories. Package includes one ESC, five ESC wires, one fan, one fan shroud, one capacitor bank, one receiver wire and hardware.
NOTE: This ESC requires soldering. Please note the connections as A + B - C.
Features:
Designed for 1/10 or 1/12 Touring and Drifting
Full aluminum housing
Racing and reverse mode
Compatible with sensored and sensorless motors
Low-Voltage Cut-Off, Thermal and Signal Loss protections
Programmable via the Hobbywing Multifunction LCD Program Box (HWA30502001)
Specifications:
Voltage: 7.4-11.1V (2-3S LiPo)
Continuous Current: 120A
Peak Current: 720A
Motor Limit with 2S LiPo/5-6 NiMH: 3.5T
Motor Limit with 3S LiPo/8-9 NiMH: 8.5T
Fan Size: 25x25x10mm
Fan Voltage Range: 5-8V
Size: 40x30x21mm(w/o Fan)
Wire: 12AWG
This product was added to our catalog on May 11, 2022
SPMX52S50H3, Spektrum RC 2S Smart LiPo 50C Hard Case Battery Pack (7.4V/5000mAh) w/IC3 Connector
The Spektrum RC 2S Smart LiPo 50C Hard Case Battery Pack with IC3 Connector provides pilots and drivers with an array of Smart benefits; Not only are charging parameters and performance data stored and uploaded automatically to Smart chargers, but no balance lead is needed — just one easy IC connection.
Smart G2 batteries come from the factory programmed to discharge automatically to a safe storage voltage of 3.90V after 72 hours of inactivity. The benefits include longer battery life, better performance over the life of the pack, and the peace of mind that comes from knowing your Smart battery is maintenance-free. You can change the battery's Auto Storage settings based on your own preferences. G2 batteries also offer a storage discharge rate that's three times faster than the previous G1 Smart batteries.
Enjoy the Smart Battery advantage of not having to set your own charging preferences. When a Smart G2 LiPo battery is connected to a Spektrum Smart charger, its unique charging parameters and health information upload to the charger from the battery's integrated memory microchip. Through the charger you can view and set preferences such as charge rates, so all that's required to charge the pack is connecting it to your Smart charger. That's the Smart Battery Advantage!
Note: G2 batteries require the use of a Spektrum™ G2 Smart Charger or earlier Smart Charger with G2 update.
Features:Simpler and safer to useBalance charge through the IC3® or IC5® connector data wire — with only one connection, no balance lead requiredFaster Auto Discharge at up to 1.5A to safe storage voltage for long battery life and improved performanceThicker internal metal side plates protect cells and improve heat dissipationIntegrated microchip stores unique parameters for each batteryIC3® and IC5® connectors are also compatible with EC3™ and EC5™ stylesSpecifications:Battery Type: LiPo (3.7V per cell)Charge Protection Circuitry: YesConnector Type: IC3Maximum Charge Rate: 5CBattery Capacity: 5000-5999mAhWatt Hours: 37Maximum Burst Discharge Rate: 50CProduct Height: 0.98" (25mm)Application: SurfaceBattery Voltage: 7.4VBattery Balance Connector: G2 SmartCapacity: 5000mAhHard Case: YesNormal/Standard Charge Current: 5ANumber of Cells: 2Product Weight: 10.58oz (300g)Wire Gauge: 12 AWGNormal/Standard Charge Rate: 1CProduct Length: 5.45" (138 mm)Product Width: 1.8" (46 mm)
This product was added to our catalog on July 31, 2024
SPMXC1020, Spektrum RC S120 USB-C Smart Charger (3S/20W)
The Spektrum S120 USB-C Smart Charger features Spektrum Smart Charging technology in a small and simple to use platform. This 20W charger easily charges compatible Spektrum Smart batteries conveniently from almost any USB power source. When a Spektrum Smart battery is connected, the S120 immediately detects the battery information and automatically begins to charge. Spektrum Smart charging is designed to be safe, intuitive and convenient so you can simply look forward to putting your batteries back to action! Charging is easy with the Spektrum S120 USB-C Smart Charger. Simply use the included USB cable to supply power to the S120 Smart Charger from a USB power source (not included). Plug in your Spektrum Smart battery (Lipo versions require the balance lead to be connected as well as the main lead) and the charger will automatically start charging. Monitor your charging status via a blinking purple or yellow LED. Once your charging is complete the LED will glow green. Spektrum Smart Charging virtually eliminates the hassle from charging your LiPo batteries. This is made possible by an integrated microchip on each Smart battery that communicates with your Smart charger to automatically determine the best charging settings. While all hobbyists will enjoy this simple experience, advanced hobbyists can take advantage of unique data such as cycle count, unhealthy activity like overcharge and discharge, battery temperature, C rating and much more, all saved within each battery. Additionally, automatic discharge to storage ensures a better, and healthier, lifespan for your batteries.Features:
Easily charges compatible smart batteries from convenient USB power (power supply not included)
Automatically detects smart battery information and begins charging when connected
Compatible with 2-3 cell Smart LiPo Batteries
Note: This charger supports IC5 batteries, but does not include the IC5 lead. The IC5 connector (SPMXCA508) is sold separately.
Specifications:Type: USB ChargerInput:5-12VDC USB charge port, USB type C cable included, power supply required# Cells: 2-3 Cell LiPo, 6-7 cell NiMHCharge Rate: 4.35V per cell x3 for a 3 cell LiHV, 2A, Not selectableInput Connector: USBOutput Connector: IC3Battery Type: Only compatible with Spektrum SMART batteriesLength: 2" (51mm)Width: 2" (51mm)Height: 0.55" (14mm)Includes:
(1) S120 USB-C Smart Charger
(1) USB-C to USB Cable
(1) Product Manual
This product was added to our catalog on May 31, 2024
SPMXSE1100, Spektrum RC Firma 100 Amp Brushless 3S Smart ESC
The Spektrum Firma 100 Amp Brushless 3S Smart ESC combines "plug-and-play" simplicity with the ability to communicate with other Smart electronics. Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best.
With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity.
Firma ESCs not only gather the data but also send it to your transmitter in real time, instead of only storing it for after-run study. You're able to adjust settings as needed to boost performance on the go. The Firma Smart single-wire telemetry solution has been tested for quality and performance by the best brands in RC. Their verdict? Smart technology is both simpler and superior!
Features:
Smart all-in-one telemetry
Fast, powerful 32-bit ARM M4 processor
Waterproof
Multiple options for easy programming:
Button programming
Smart ESC Programming Box
SmartLink USB Updating and Programmer application
Multi-point protection:
Over-current protection
Automatic LiPo low-voltage cutoff
Thermal protection
Failsafe protection
Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer
Ideal for 4WD 1/10th – 1/8th scale surface applications running on 3s Lipo setups
High current adjustable BEC (6v or 7.4v @ 4 Amps)
Compact for easy installation in most applications
Ready to install — no soldering required
Rugged plastic case with mounting tabs
Aluminum heat sink for high efficiency
Cooling fan
Adjustable high-power BEC
Firmware updatable through the Smart ESC Programming Box
High heat-resistant IC™ connectors, backwards compatible with EC™ connectors
Limited 1-year warranty
Specifications:
Auto Cutoff: Yes
Battery Type: LiPo (3.7V per cell)
BEC: Yes
BEC Continuous Current: 4A
BEC Voltage: 6V and 7.4V selectable
Brakes: Yes
Connector Type: IC5
Drive Type: Forward/Brake/Reverse
Forward: Yes
Input Voltage: 6.0V - 9.6V (2-4S LiPo, 5-9 cell NiMH)
Low-Voltage Cutoff Programmable: Yes
Maximum Burst Current: 650A
Maximum Continuous Current: 100A
Motor Output Lead: 4mm Female Bullet
Motor Type: Brushless - Sensorless
Output: 100A
Output Connector: 4mm Bullet
Overload Protection: Yes
Product Height: 1.33" (34 mm)
Product Length: 1.7" (43 mm)
Product Weight: 0.306lbs (139g)
Product Width: 1.53" (39 mm)
Programmable: Yes
Reverse: Yes
Technology: Smart
Time Delay Brake: Yes
Water-Resistant: Yes
Includes:
(1) Spektrum™ Firma™ Smart ESC
(1) Spektrum Smart sticker sheet
(1) Product Manual
Needed to Complete:
Spektrum™ Surface Receiver
Spektrum Smart Technology LiPo Battery
Spektrum Transmitter
This product was added to our catalog on March 12, 2021.
SPMXSE1120, Spektrum RC Firma 4S 120 Amp Brushless Smart ESC
The Spektrum Firma 4S 120 Amp Brushless Smart ESC combines "plug-and-play" simplicity with the ability to communicate with other Smart electronics — together, creating the best-performing RC system for your vehicle imaginable.
Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best.
With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity.
Firma ESCs not only gather the data but also send it to your transmitter in real time, instead of only storing it for after-run study. You're able to adjust settings as needed to boost performance on the go. The Firma Smart single-wire telemetry solution has been tested for quality and performance by the best brands in RC. Their verdict? Smart technology is both simpler and superior!
Features:
Smart all-in-one telemetry
Fast, powerful 32-bit ARM M4 processor
Waterproof
Multiple options for easy programming:
Button programming
Smart ESC Programming Box
SmartLink USB Updating and Programmer application
Multi-point protection:
Over-current protection
Automatic LiPo low-voltage cutoff
Thermal protection
Failsafe protection
Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer
Ideal for 1/8th scale surface applications running on 4s Lipo setups
High current adjustable BEC (6v or 7.4v @ 4 Amps)
Compact for easy installation in most applications
Ready to install — no soldering required
Rugged plastic case with mounting tabs
Aluminum heat sink for high efficiency
Cooling fan
Adjustable high-power BEC
Firmware updatable through the Smart ESC Programming Box
High heat-resistant IC™ connectors, backwards compatible with EC™ connectors
Limited 1-year warranty
Specifications:
Auto Cutoff: Yes
Battery Type: LiPo (3.7V per cell)
BEC Continuous Current: 4A
BEC Voltage: 6 and 7V selectable
Brakes: Yes
Connector Type: IC5
Drive Type: Forward/Brake/Reverse
Input Voltage: 6.0V - 14.4V (2-4S LiPo, 5-12 cell NiMH)
Low-Voltage Cutoff Programmable: Yes
Maximum Burst Current: 830A
Maximum Continuous Current: 120A
Motor Connector: 4mm Female Bullet
Overload Protection: Yes
Product Height: 1.33" (34 mm)
Product Length: 1.7" (43 mm)
Product Weight: 0.337lbs (153g)
Product Width: 1.53" (39 mm)
Programmable: Yes
Reverse: Yes
Technology: Smart
Time Delay Brake: Yes
Water-Resistant: Yes
Includes:
(1) Spektrum™ Firma™ Smart ESC
(1) Spektrum Smart sticker sheet
(1) Product Manual
Needed to Complete:
Spektrum™ Surface Receiver
Spektrum Smart Technology LiPo Battery
Spektrum Transmitter
This product was added to our catalog on January 20,2024
SPMXSE1160, Spektrum RC Firma 160 Amp Brushless Smart ESC
Spektrum Firma 160 Amp Brushless Smart ESC. Like every component in the Spektrum Smart ecosystem, Firma Smart ESCs combine "plug-and-play" simplicity with the ability to communicate with other Smart electronics — together, creating the best-performing RC system for your vehicle imaginable.
Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best.
With Firma Smart ESCs, you'll be better connected to your vehicle than ever before — without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity.
Firma ESCs not only gather the data but also send it to your transmitter in real time, instead of only storing it for after-run study. You're able to adjust settings as needed to boost performance on the go. The Firma Smart single-wire telemetry solution has been tested for quality and performance by the best brands in RC. Their verdict? Smart technology is both simpler and superior!
Features:
Smart all-in-one telemetry
Fast, powerful 32-bit ARM M4 processor
Waterproof
Multiple options for easy programming:
Button programming
Smart ESC Programming Box
SmartLink USB Updating and Programmer application
Multi-point protection:
Over-current protection
Automatic LiPo low-voltage cutoff
Thermal protection
Failsafe protection
Developed and designed by Spektrum™ engineers, in partnership with the industry's leading ESC manufacturer
Compact for easy installation in most applications
Ready to install — no soldering required
Rugged plastic case with mounting tabs
Aluminum heat sink for high efficiency
Cooling fan
Adjustable high-power BEC
Firmware updatable through the Smart ESC Programming Box
High heat-resistant IC™ connectors, backwards compatible with EC™ connectors
Limited 1-year warranty
Specifications:
Forward: Y
Reverse: Y
Brake: Y
Time Delay Brake: Y
Continuous Maximum Current: 160A (1050A Max Burst)
Input Voltage: 11.1 - 29.6V
Input Connector Types: IC5
Output Connector Types: Female 6.5 Bullets
Length: 70
Width: 77
Height: 44
Weight: 280g
BEC Voltage: 6V / 8.4V
Includes:
(1) Spektrum™ Firma™ Smart ESC
(1) Spektrum Smart sticker sheet
(1) Product Manual
This product was added to our catalog on October 23, 2021
