103076-4, Spartan SR 6S (Self Righting) 36" Brushless Boat (Optional Trailer Available) 36″ Reinforced Deep-V Hull Made from lightweight vacuum-formed ABS Self-righting flood chamber Pre-applied graphics Quick-release electronics tray Rigid Injection-Molded Clipless Hatch Four quick-release hatch nuts with tool Foam seal keeps water out Includes optional tool-free wingnuts Up to 50 MPH with Dual 3s LiPo Batteries VXL-6s™ Marine Electronic Speed Control Water-cooled case Three drive profiles Sport Mode - forward / brake / reverse Race Mode - forward / brake Training Mode™ - 50% forward / brake / 50% reverse (patented) Built-in two-stage low-voltage detection for LiPo batteries NiMH battery packs: 14 cells (16.8 volts) LiPo battery packs: 4-6 cells (14.8 to 22.2 volts) Velineon 540XL Brushless Motor Ultra high-temperature sintered Neodymium magnets Efficient, high-speed ball bearings 1800 kV 5 mm output shaft Water-cooled jacket Traxxas Stability Management (TSM) Improves straight line acceleration Never dulls throttle or slows the vehicle Adjusts from off to 100% assistance from the transmitter TQi 2.4 GHz Radio System 2-channel transmitter 5-channel micro receiver (6533) with fail-safe security and integrated telemetry ports Automatically stores and loads settings for up to 30 Traxxas Link enabled models Programmable multi-function knob Patented waterproof receiver box Extra-Long 218 mm Battery Tray Centralizes battery weight Allows fore and aft battery positioning Accommodates multiple battery configurations Secure hook and loop straps Driveline Heavy duty 4.7 mm diameter flex shaft Quick-release motor collet Blue-anodized aluminum drive strut Low-maintenance bushings High performance prop Steering Waterproof digital 2056 servo Blue-anodized aluminum rudder with water pickup Precision-Cut Stainless Steel Trim Tabs and Turn Fins Stainless Steel Hex Hardware Used Throughout This product was added to our catalog on March 14, 2024

Read more less

57046-4, Traxxas DCB M41 Widebody 40" Catamaran High Performance 6S Race Boat w/TQi 2.4Ghz Radio & TSM Traxxas DCB M41 Widebody 40" Catamaran - Extreme Power with the Style to Match! The Traxxas DCB M41 Widebody 40" Catamaran was built for extreme power and speed. With a powerful 6s motor this boat can reach speeds in excess of 50mph! Built with a Twin-hull catamaran design the DCB M41 can handle high speeds even in less than ideal conditions. Additionally this boat is equipped with Traxxas Stability Management (TSM) bringing another level to stability that other boats cannot match. With 6s power, off the charts stability and dependable Traxxas components leave your competition at the docks with the DCB M41 Widebody! Traxxas has faithfully captured the incredible looks and performance of the DCB M41 in a detailed scale replica that is versatile, fun, and fast. Designed by DCB (Dave’s Custom Boats) founder Dave Hemmingson, is one of the largest full size models offered in the DCB M-Series. The full size boat with its precision sculpted design and a pair of Mercury Racing 1350 engines speeds across the water at 175mph!  Features: 50+mph on 6S LiPo 40" DCB M41 Widebody catamaran replica Stable Twin-hull catamaran performs across waves and smooth water Water-cooled, waterproof VXL-6s Marine speed control Traxxas High-Current Connectors (patented) Velineon 540XL high-output brushless motor with high flow water-cooling jacket Quick-release Power Module integrates power system with waterproof electronics Adjustable battery trays with hook-and-loop straps Blue-anodized aluminum rudder support, rudder, and drive strut Stainless steel trim tabs, and hardware TQi 2.4GHz radio system and 5-channel receiver Access the Traxxas Link app with the Traxxas Link Wireless Module (#6511) (sold separately) Traxxas Stability Management® (TSM) makes it easy to go fast Waterproof high-torque steering servo Specifications: Hull Type: Vacu-formed ABS, catamaran, shoebox style Hull Length: 39.5" (1003mm) Overall Length: 40.6" (1030mm) Beam: 10.5" (267mm) Height: 5.95" (151mm) Deadrise & Transom: 14.5 degrees Weight: 86.7 ounces (2.46 kg) Speed Control Type: Traxxas Velineon VXL-6s, water-cooled Input Voltage: 2-6 LiPo cells (14.8-22.2 volts DC) BEC Voltage: 6.0 VDC BEC Current: 3A Thermal Protection: Thermal shutdown Low Voltage Detection: Yes (user enabled) Motor (electric): Traxxas Velineon 540XL Brushless, water-cooled Drive System: Direct drive, 0.15 inch flex cable Outdrive: Adjustable aluminum Prop: 2-blade composite, 42x59mm Transmitter: TQi 2.4GHz (2-channel) Receiver: 6533 2.4GHz Traxxas Stability Management 5-channel Servo: 2056 High-torque waterproof Skill Level: 2 Needed To Complete: (4) "AA" Batteries (for transmitter) (2) 2S or 3S LiPo Battery w/iD Connector (1) Compatible Battery Charger This product was added to our catalog on May 1, 2022

Read more less

ARA4305V3, Arrma Vorteks 4X4 3S BLX 1/10 RTR Brushless Stadium Truck (Green) w/2.4GHz Radio The Arrma Vorteks 4X4 3S BLX represents the highest level of speed and technology found yet in the proven tough ARRMA 4X4 platform. The Vortex 4x4 includes a 2S or 3S compatible Spektrum Firma 3200Kv brushless motor, and is a rocket right out of the box. Using a 3S LiPo battery and an optional pinion gear, it is the first ARRMA 4X4 3S BLX model capable of 60mph and more! The proven tough ARRMA 4X4 platform lets you bash at high speeds in almost any environment — off-road, on dirt and grass, on parking lots and over paved and asphalt surfaces. Its durability comes from a strong composite chassis featuring extended height dirt defenders, oil-filled shocks with silicone O-rings, metal geared differentials and more. Rugged bumpers and high-traction dBoots Katar tires mounted on tough, gun-metal colored wheels add to its unstoppable performance. The VORTEKS 4X4 3S BLX also includes a sleek, new stadium truck body with tough, injection-molded wing and protective roof skids. ARRMA adds the security of advanced Spektrum electronics to the VORTEKS Stadium Truck's speed and toughness to create a totally exhilarating bashing experience. With its included DX3 DSMR 2.4GHz radio system, SR6200A receiver and Firma 100A ESC, this is the first ARRMA 1/10 scale 4X4 model to provide the benefits of AVC (Active Vehicle Control) and Smart technology straight out of the box. With the AVC system's on-demand traction control, you can dial-in extra stability as needed to carve corners or nail jumps without backing off the power. You have full-throttle freedom over rough terrain, slick surfaces and loose dirt. When you don't want the extra traction, just dial back the stability. The DX3 radio's AVC system works behind the scenes, making hundreds of minute steering and throttle adjustments per second to keep the VORTEKS Stadium Truck precisely on the line you want to hold. Download the optional Spektrum Dashboard app to your mobile device — it's available free from the iPhone App Store and Google Play — to take full advantage of the Smart electronics' telemetry capabilities. Once you connect your mobile device wirelessly via Bluetooth to the VORTEKS Stadium Truck's DX3 transmitter, you can use it to view top speed, battery voltage and other essential data in real time (requires an optional BT2000 Bluetooth Module, available separately). Features: Stadium truck body with tough, injection molded wing and protective roof skids Adjustable body mounts High-traction, vented dBoots® Katar™ multi-terrain tires mounted to tough, gun-metal color wheels Spektrum™ 3660 3200Kv brushless motor with ARRMA® heatsink and cooling fan and Safe D pinion Spektrum™ Firma™ 100A Smart ESC Spektrum™ 2.4GHz DX3 transmitter and SR6200A receiver Smart radio system with AVC® (Active Vehicle Control®) Spektrum™ SPMS651 metal-geared servo Strong composite chassis with extended height dirt defenders Easy-access modular design Adjustable turnbuckles Steering system with stone clearance Adjustable ride height Wheelie bar Rubber shielded bearings throughout Durable 37T 1.35 module metal differential gears and silicone O-rings Castellated slipper pad and sliding gear mesh Plastic locknut for slipper 2-Year limited warranty; see website support for details. Double wishbone suspension front and rear Oil-filled shocks with silicone O-rings Specifications: Approximate Assembly Time: No assembly required Ball Bearings: Full set, rubber shielded Battery: Sold Separately Body: Painted, decalled and trimmed Brakes: Integral with ESC Chassis: Molded Composite Completion Level: Ready-To-Run Differential: 2 Gear Diffs Drivetrain: 4WD Final Drive Ratio: 9.03 Power Type: Electric Gear Pitch: 0.8m Internal Gear Ratio: 2.85 Motor Type: Brushless - Sensorless Pinion: 18T Product Height: 6.42" (163 mm) Product Length: 18.5" (470 mm) Product Weight: 6.49 lbs (2.95kg) Product Width: 13.31" (338 mm) Radio: Included Receiver: Included Scale: 1/10 Servos: Included Shock Type: Oil-Filled, Coil-Over Springs Speed Control: Included Spur Gear: 57T Suspension: Independent Vehicle Type: Stadium Truck Wheelbase: 11.3" (287 mm) Includes: (1) ARRMA® VORTEKS™ 4X4 3S BLX 1/10 Scale 4WD Electric Stadium Truck RTR (1) Spektrum™ Firma™ 100A Smart Waterproof ESC (1) Spektrum™ Firma™ 3660 3200Kv Brushless Motor (1) Spektrum™ 2.4GHz DX3 Smart DSMR® 3-Channel Transmitter (1) Spektrum™ SR6200A AVC® Receiver (1) Spektrum™ SPMS651 7kg Waterproof Metal-Geared Digital Servo (1) 23T Spline servo saver (1) Product Manual Needed to Complete: 2S or 3S 5000mAh 50C Hardcase LiPo Battery w/EC5 or iC5 connector (Maximum battery dimensions 156x51x48mm) Compatible Charger (4) AA Batteries LiPo Safe Charging Bag This product was added to our catalog on March 3, 2021

Read more less

ARAG2000, AR390205 BLX4074 2050kV 4 Pole 6S Brushless Motor Product Specifications Manufacturer # AR390205 Connector Type 3.5mm Bullet Motor Design Inrunner Motor Type Brushless

Read more less

AXIM4260, AX24260 AE-3 Vanguard ESC Brushless EXO RTR

Read more less

CSE010-0150-02, Castle Creations Sidewinder Micro 2 1/18th Scale Brushless Car Package (5300KV) The Sidewinder Micro 2 ESC boasts updated circuitry and added functionalities. Castle engineers are committed to taking full advantage of advancements in component quality and continuous improvements in software design. As a result, we are thrilled to introduce the Sidewinder Micro 2. The Sidewinder Micro 2 is perfect for 1/18th scale 2WD vehicles and smaller 4WD (up to 2 lbs.) such as the Team Associated RC18B2 or Dromida SC4 SCT. Whether you are converting to a brushless setup or simply needing more power than your current brushless power system is putting out, there is a Sidewinder Micro 2 combo to fit your needs. The Castle 20mm 0808 Brushless Motors are a perfect companion to the Sidewinder Micro 2 and are available in 4100Kv, 5300Kv, or 8200Kv packages. The included 0808 series 5300Kv motor is suitable for on-road and off-road applications running up to 3S LiPo and weighing in at up to 2.5lbs. Using the same 4 pole technology found in the larger Castle motors, the 0808 series provides the increased efficiency and torque 4 pole motors are known for.Sidewinder Micro 2 Features: Improved BEC Functionality - Now adjustable: 5.5V or 7.5V Improved Audible Alerts - The ability to diagnose and resolve problems in the field are made easy as this ESC will communicate with audible tones when certain conditions are present. Alerts are present for start fail, voltage cutoff, radio glitch, over-temperature, over-current and excessive load detections. Improved Startup - Updated circuitry and refined software makes for ultra-smooth starts! Link Live functionality added - Link Live is a way for the controller to communicate power system information to an external device. This feature, when enabled, will allow users to experience real-time telemetry data such as battery voltage, ESC temperature, motor power output and battery ripple. Compatibility with the Futaba S.BUS® T4PX transmitter is coming soon (Requires purchase of Castle S.BUS2 Telemetry Link) Transmitter Programming - Manual programming settings include Brake/Reverse Type, Voltage Cutoff, Brake Amount, Drag Brake and Motor Type. Castle Link Programming - With the purchase of Castle Link USB device, you will have access to the full programming suite of adjustable settings that tune and tweak your vehicle to your preferences, resulting in an incredible driving experience! Click here for the full list of Castle Link Sidewinder Micro 2 settings. Firmware Updates - With the purchase of Castle Link USB device, you will have access to all firmware updates, including added feature sets released from Castle Engineering at no charge. Specifications: Sidewinder Micro 2 ESC Application: 1:18th scale RC hobby vehicles weighing up to 2 lbs. Input voltage: 2S-3S LiPo, 4-9 cell NiMH BEC Specifications: Adjustable: 5.5V or 7.5V (2A Peak), default 5.5V Size: ~22mm x 38mm Weight (w/wires): ~26g Connector Type: The Sidewinder Micro 2 has 3.5mm bullet connectors on the motor wires and the battery input wires are bare. You must add the connector of your choice to the battery leads. We recommend a high current connector rated for at least 40 amps. 0808 20MM Brushless Motor Kv: 5300Kv Size: L: 1.5" (38mm) Diameter: 0.79" (20mm) Shaft: 0.08" (2mm) Weight: 1.8 oz (50g) Connector Type: 3.5mm gold connectors (female connectors included) Maximum Input Voltage: 2-3S LiPo, 4-9 cell NiMH (2S max 8200Kv) This product was added to our catalog on March 2, 2021

Read more less

CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV) The Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo with 2028 Sensored Motor is a great way to take your build to the next level with Castle’s cutting edge sensored large scale brushless power. The MAMBA MONSTER X 8S COMBO is ready to power any R/C vehicle weighing up to 25lbs, and running all the way up to 8S LiPo. This motor and ESC combo is designed for heavy, high speed rigs, and you'll experience smooth low-end control, without sacrificing power, punch, or speed. The MAMBA MONSTER X 8S utilizes Castle’s breakthrough technology, CRYO-DRIVE. By reducing the rate at which the ESC heats up and removing heat more efficiently, your setup will be able to handle higher gear ratios, in heavier vehicles, with longer runs. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 40mm cooling fan and a forged elliptical fin heatsink, the design maximizes airflow throughout the system, taking thermal performance to a whole new level. The ESC was designed with a robust aluminum casing, and the epoxy potting guarantees protection around the circuitry and ensures all-weather use. Mamba Monster X 8S is a beast, ready to take on the harshest of environments and still perform. You can easily optimize the ESC for any driving condition, from rugged terrain to smooth pavement to the perils of rock and gravel. Create, save and download setup profiles through the Castle Link Programming Suite on your Windows™ PC, or wirelessly with the convenience of the new B-Link™ Bluetooth™ Adapter and Castle Link app for Android or iOS. When paired with the Castle sensored 2028-800KV motor, users with heavy, high power rigs will experience controllable low-end control without sacrificing power, punch or speed. SmartSense™ mode uses the motor’s sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is spinning, it seamlessly transitions to Castle’s ultra-efficient sensorless mode. You’ll put more power to the ground, where it should be, instead of wasting it through raw heat and RPMs. NOTE: This is not a direct replacement to the Mamba XLX. The XLX still handles rawer full throttle power in the most extreme setups. Features: ESC: Input Voltage Range 2S-8S LiPo Sensorless, Sensored and SmartSense™ Running Modes Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V) CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the electronics and promote efficient heat transfer Premium forged heatsink with elliptical fins for superior air flow and increased heat dissipation Oversized factory equipped thermally controlled 40MM cooling fan Compatible with S.BUS2 Telemetry Link and Futaba T4PX and T7PX transmitters Waterproof design for all weather conditions Data logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for "on-the-fly" adjustments using your transmitter Audible alerts for easy diagnosis of common issues such as motor-over-temperature and low-voltage cutoff Convenient transmitter programming for six common adjustable settings including cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store Proudly designed and manufactured in Olathe, KS USA and backed by Castle Creations' 1-year warranty Motor: The 2028 Extreme can easily run in the 10 horsepower range (Burst power output for duration's typical of vehicle acceleration.) Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Proprietary winding techniques allow Castle Creations to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Dual sensor ports to ensure optimal installation in your large-scale vehicle. Updated modern and sleek design that looks as cool as it performs. Specifications: ESC: Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes, waterproof Cooling Fan: Yes, factory equipped (40MM), fully removable** (See Product Use Statements below) Size: L x W x H 69.5mm x 54.1mm x 47mm Weight (with no battery connector): 5.75 oz. (163 grams) Connectors: 6.5mm female bullets for motor connection Motor: Input Voltage Range: 12S MAX Kv: 800 Max. RPM: 45,000 Minimum Input Voltage: 3S Maximum Input Voltage: 12S Sensored Capable: Yes Can Length: 4.4" (113.2mm) Can Diameter: 2.2" (57mm) Weight (w/wires): 44 oz./1.25kg Shaft Size: Length: 30mm Diameter: 8mm Mounting Hole Specifications: 4mm holes @ 30mm spacing. Cooling Fan: Available, but not included. See 011-0019-00 here. Connectors: 8.0mm male connectors Recommended ESC: Mamba XL X Running modes: Sensorless and Sensored Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs. Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately). Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters. Product Use Statements: Recommended battery capacity for 1:6th scale vehicles is 5000mah. Castle recommends using 50C continuous discharge or higher LiPo batteries. Surge ratings should never be used to determine a pack’s suitability for a brushless application. Castle recommends a high current connector designed for high-powered electric systems, rated for 100+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors. Applying voltages higher than 33.6V will cause irreparable damage to ESC. Although Mamba Monster X 8S is waterproof, it is NOT intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt. The cooling fan must be removed prior to driving in wet conditions. *Fan is not waterproof. Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the motor or ESC. The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the Running & Maintaining document in the resources tab above for info on running and maintaining motors in wet environments. Application Guidelines: Mamba Monster X 8S and 2028-800Kv motor is intended for use in 1:6 scale vehicles weighing up to 25 lbs. and up to 8S LiPo. Vehicle Examples: Traxxas™ X-Maxx & Unlimited Desert Racer; Arrma™ Kraton 8s & Limitless; Losi™ Super Rock Rey & Audi R8; Redcat™ Shredder (optional motor mount and modifications may be necessary to install motor). Includes: Mamba Monster X 8S ESC 4-POLE Sensored 2028-800KV Motor Castle Sensor Harness Adapter (installed) 250mm Sensor Wire Mamba Decals Coupon for free Castle Link USB ESC Quick Start Guide Motor Quick Start Guide This product was added to our catalog on April 4, 2021

Read more less

CSE010-0167-01, Castle Creations Mamba XLX 2 1/5 Sensored Brushless ESC/Motor Combo (800Kv) w/2028 Motor The Castle Creations Mamba XLX 2 1/5 Scale Sensored Brushless ESC/Motor Combo with 2028 800Kv motor is a product guaranteed to redefine the limits of large scale R/C. Though it shares the name of its predecessor, the Mamba XLX, this is an ESC that lives in a class of its own. Reengineered from the ground up, the Mamba XLX 2 is packed with a potent combination of design, hardware and software advancements that will set a new standard for large-scale power systems. Designed for 1/5 Scale models weighing up to 42 lbs, the XLX 2 is an incredible power upgrade for the Losi DBXL-E and Super Rock Rey, Arrma Kraton 8S and Outcast 8S, or Traxxas X-Maxx models! If you are looking for the ultimate upgrade for your speed run, drag racing or off road rigs - the XLX 2 is a true heavyweight, with no contenders. CRYO-DRIVE: MORE POWER – COOLER TEMPS – LONGER RUNS Castle’s latest break-through technology, minimizes the amount of time the ESC’s electrical components spend generating heat. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 50mm fan and a forged elliptical fin heatsink, the design maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling. NOTE: Some vehicles may require aftermarket parts to allow ESC and/or motor fitment.  Features: Sensored, Sensorless and SmartSense™ running modes Powerful Integrated 20A Peak Adjustable BEC (5.25V-8.0V) Premium forged heatsink with for superior airflow and increased heat dissipation Oversized factory equipped thermally controlled 50mm fan  Waterproof design for all weather conditions.  ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to  protect the components and promote efficient heat transfer Data-logging capability to capture and record performance data from your vehicle Auxiliary wire functionality for “on the-fly” adjustments using your transmitter Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake Easily tune and update ESC with USB and Bluetooth™ programming options.   Castle Link USB programming kit (coupon included with purchase) Optional smartphone-based programming  with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store. Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1-year warranty Specifications: ESC: Input voltage range: 3S-8S LiPo Length: 3.98” (101.2mm) Width: 2.49” (63.3mm) Height: 2.2” (55.8mm) On/Off Switch: Yes, waterproof* Cooling Fan: Yes, thermally controlled factory equipped (50mm) fully removable** Weight: 13.1 oz (371g) Running Modes: Sensored, Brushed, Sensorless and SmartSense™ when paired with a Castle 4-POLE 12-SLOT Sensored Motor. (Dust cover included in package for non-sensored operation) Wire Gauge: 8AWG Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX, T7PXR Transmitters. Items Needed: Battery connectors designed for 150+ amps continuous, such as Castle 6.5mm polarized or CC BULLET 8.0MM Motor: Application Guidelines: 1:5th Scale vehicles weighing up to 30 lbs.  Vehicle Examples: Losi DB XL-E,™ Losi Super Rock Rey™, Arrma Kraton 8s™, Arrma Outcast 8s™, Traxxas X-Maxx™ (Some vehicles may require aftermarket parts to allow ESC and/or motor fitment) Input Voltage Range: MIN: 3S LiPo, MAX: 8S LiPo 33.6V Kv: 800Kv Max. RPM: 45,000 Diameter: 2.22” (56.3mm) Length: 4.44” (112.7mm) Shaft Size: 30mm (Length), 8mm (Diameter) Weight (w/wires): 44 oz./1.25kg Mounting Hole Specifications: Holes: 4mm, Spacing: 30mm Connectors: 8.0mm male connectors, 300mm Direct Connect Sensor Wire Includes: Mamba XLX2 ESC 2028-800kv Sensored Brushless Motor 300mm Direct Connect Sensor Wire Mamba Decals Mamba XLX2 Quick Start Guide Sensor port dust cover Coupon for free Castle Link USB This product was added to our catalog on October 12, 2021

Read more less

CSE010015504, Castle Creations Mamba X 1/10 Brushless Combo w/1406 Sensored Motor (7700kV) The Castle Creations Mamba X 1/10 Brushless Combo includes the Mamba X, with the awesome 1406 Sensored motor to create a all in one system perfect for 1/10 scale on-road cars using 2S, lightweight - conservatively geared stadium trucks and buggies that want the ultimate in speed. The motor included in this combo is NOT recommended for use in 2WD or 4WD short course trucks. The Mamba X is going to shake things up. Extremely versatile, and capable of powering a wide variety of applications and vehicles the Mamba X is ideal for racing at the track with your 2wd buggy, bashing through mud puddles in your monster truck, or navigating a hardcore trail with your crawler. The high performance Mamba X includes an integrated and powerful 8A adjustable BEC and can push the most extreme 1/10th scale setups and 1/8th scale race buggies. Castle Creations 1406 Sensored 4-Pole Brushless Motors combine rotor position sensor technology with an improved high power and high efficiency motor design to deliver ultra smooth startup, precise low speed control, predictable power delivery, incredible torque, and lightning fast response. Through the use of Castle's Smart Sense technology, the position of the rotor is always known by the ESC. This eliminates the possibility of encountering cogging or inconsistency during startup, and allows the 1406 to deliver PRECISE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for. Features: ESC Wide 2S to 6S input voltage range Sensored Motor Support (Castle X-Series Sensor Harness Included) Waterproof 8A Adjustable BEC (5.25V-8.0V) Data-logging Rugged CNC Aluminum Case Castle Link Programming Support SmartSense™ Integrated Capacitors Removable 30mm Cooling Fan Integrated 4mm Bullet Connectors 12 AWG Power Wires Waterproof Switch Audible Alerts The Mamba X is proudly designed and manufactured in Olathe, Kansas Backed by Castle Creations’ 1-year warranty and unparalleled "make-it-right" customer support Motor 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 13 AWG high strand wire with silicone insulation Kevlar wrapped rotor 6061-T6 Billet aluminum heatsink can High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: ESC Input Voltage Range: 2S LiPo (7.4V) to 6S LiPo (25.2V) BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes Cooling Fan: Yes, factory equipped (30mm), fully removable** (see Product Use Statements below) Size (LxWxH): 2.14x1.39x1.18" (54.4x35.2x30.0mm) Weight (with wires): 3.56 oz. (101g) Connectors: 4.0mm female bullets for motor connection. Items Needed for Operation: Battery Connector Application Guidelines: Intended for up to 6S (25.2 Volt) operation in vehicles weighing less than 9bs/4kg Recommended Motors: Castle 1406, 1410 and 1415 Sensored motors Max. Recommended Vehicle Weight: Less than 9bs/4kg, with batteries, ready-to-run Telemetry Link Capable: Yes Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free link included in package) and freely downloadable Castle Link Windows software. Motor Input Voltage Range: 2S LiPo Kv: 7700 Max. RPM: 100,000 Length: 49.5mm Diameter: 36mm Weight (w/wires): 189 g / 6.7oz Shaft Size: 15mm Diameter: 1/8" (3.17mm) Mounting Hole Specifications: M3 @ 25mm Cooling Fan: Optional - Coming Soon Connectors: 4mm male Castle Bullet Connectors Application Guidelines: 1:10 scale on-road cars using 2S, lightweight stadium truck and buggies geared conservatively. Not for use in 2WD or 4WD short course trucks. Recommended ESC(s): Mamba Max Pro Max. Recommended Vehicle Weight: Vehicles up to 4lbs. Tech Notes: Running modes: SMARTSENSE™, Sensored, Sensorless Product Use Statements: *Although Mamba X is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC and motor with clean water after exposure to corrosives or dirt. While the motor and controller may be waterproof, Castle suggests users confirm that the rest of their vehicle, including the batteries, servos, radio and chassis are also waterproof before exposing them to liquids of any kind. **The cooling fan must be removed prior to driving in wet conditions. It is not waterproof. Tech Notes: Mamba X setups frequently hit 100+ amps in peaks and not all LiPos are created equal. Surge ratings should never be used to determine a pack's suitability for a brushless application. Recommended battery capacity for 1:10th and 1:8th scale vehicles is 5000mAh. We recommend using 30C continuous discharge or higher LiPo batteries (or high quality 25C batteries such as Traxxas® Power Cell). Our experience suggests using only mild gear ratios with NiMH cells. Do not attempt to use NiMH cells in extreme setups. Applying voltages higher than 25.2V will cause irreparable damage to ESC. We recommend a high-current connector designed for high-powered electric systems, rated for 70+ amps. Invest in connector sets made for high-powered electric systems such as our Castle 6.5mm Polarized Connectors, Castle 4.0mm Polarized Connectors, Traxxas® Power Connectors, or Deans® Ultra Plugs This product was added to our catalog on May 3, 2021

Read more less

CSE010016001, Castle Creations Mamba X SCT 1/10 Brushless Combo w/1415 Sensored Motor (2400kV) (5mm Shaft) The Castle Creations Mamba X SCT Waterproof 1/10 Brushless Combo includes the Mamba X, with the awesome 1415 Sensored motor to create a all in one system perfect for 2WD and 4WD Short Course trucks weighing up to 6.5lbs running on a 3s or 4s LiPo. The Mamba X is going to shake things up. Extremely versatile, and capable of powering a wide variety of applications and vehicles the Mamba X is ideal for racing at the track with your 2wd buggy, bashing through mud puddles in your monster truck, or navigating a hardcore trail with your crawler. The high performance Mamba X includes an integrated and powerful 8A adjustable BEC and can push the most extreme 1/10th scale setups and 1/8th scale race buggies. Castle Creations 1415 Sensored 4-Pole Brushless Motors combine rotor position sensor technology with an improved high power and high efficiency motor design to deliver ultra smooth startup, precise low speed control, predictable power delivery, incredible torque, and lightning fast response. Through the use of Castle's Smart Sense technology, the position of the rotor is always known by the ESC. This eliminates the possibility of encountering cogging or inconsistency during startup, and allows the 1406 to deliver PRECISE throttle control and BUTTERY SMOOTH starts - with the RAW POWER and LONGER RUN TIMES that Castle motors are known for. Features: ESC Wide 2S to 6S input voltage range Sensored Motor Support (Castle X-Series Sensor Harness Included) Waterproof 8A Adjustable BEC (5.25V-8.0V) Data-logging Rugged CNC Aluminum Case Castle Link Programming Support SmartSense™ Integrated Capacitors Removable 30mm Cooling Fan Integrated 4mm Bullet Connectors 12 AWG Power Wires Waterproof Switch Audible Alerts The Mamba X is proudly designed and manufactured in Olathe, Kansas Backed by Castle Creations’ 1-year warranty and unparalleled "make-it-right" customer support Motor 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 13 AWG high strand wire with silicone insulation Kevlar wrapped rotor 6061-T6 Billet aluminum heatsink can High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: ESC Input Voltage Range: 2S LiPo (7.4V) to 6S LiPo (25.2V) BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V Operating Environment: Waterproof* design allows for use in nearly any environment. Brake: Proportional Reversible: Yes, but may be disabled for racing. On/Off Switch: Yes Cooling Fan: Yes, factory equipped (30mm), fully removable** (see Product Use Statements below) Size (LxWxH): 2.14x1.39x1.18" (54.4x35.2x30.0mm) Weight (with wires): 3.56 oz. (101g) Connectors: 4.0mm female bullets for motor connection. Items Needed for Operation: Battery Connector Application Guidelines: Intended for up to 6S (25.2 Volt) operation in vehicles weighing less than 9bs/4kg Recommended Motors: Castle 1406, 1410 and 1415 Sensored motors Max. Recommended Vehicle Weight: Less than 9bs/4kg, with batteries, ready-to-run Telemetry Link Capable: Yes Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free link included in package) and freely downloadable Castle Link Windows software. Motor Input Voltage Range: 3-4S LiPo Kv: 2400 Max. RPM: 75,000 Length: 69.5mm Diameter: 36mm Weight (w/wires): 319g / 11.3oz Shaft Length: 21mm Shaft Diameter: 0.197" (5mm) Mounting Hole: M3 @ 25mm Cooling Fan: Optional, coming soon! Connectors: 4mm male Castle Bullet Connectors Recommended ESC (s): Combo includes Mamba X ESC. Recommended Applications: 2WD and 4WD Short Course trucks weighing up to 6.5lbs running on a 3s or 4s LiPo with included 1415 - 2400kv sensored motor. Running Modes: SMARTSENSE™, Sensored, Sensorless Product Use Statements: *Although Mamba X is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC and motor with clean water after exposure to corrosives or dirt. While the motor and controller may be waterproof, Castle suggests users confirm that the rest of their vehicle, including the batteries, servos, radio and chassis are also waterproof before exposing them to liquids of any kind. **The cooling fan must be removed prior to driving in wet conditions. It is not waterproof. Tech Notes: Mamba X setups frequently hit 100+ amps in peaks and not all LiPos are created equal. Surge ratings should never be used to determine a pack's suitability for a brushless application. Recommended battery capacity for 1:10th and 1:8th scale vehicles is 5000mAh. We recommend using 30C continuous discharge or higher LiPo batteries (or high quality 25C batteries such as Traxxas® Power Cell). Our experience suggests using only mild gear ratios with NiMH cells. Do not attempt to use NiMH cells in extreme setups. Applying voltages higher than 25.2V will cause irreparable damage to ESC. We recommend a high-current connector designed for high-powered electric systems, rated for 70+ amps. Invest in connector sets made for high-powered electric systems such as our Castle 6.5mm Polarized Connectors, Castle 4.0mm Polarized Connectors, Traxxas® Power Connectors, or Deans® Ultra Plugs This product was added to our catalog on February 16, 2021

Read more less

CSE011-0135-00, Castle Creations B Link Bluetooth Adapter The Castle Creations B Link Bluetooth Adapter gives you access to powerful Castle Link ESC tuning features right from your iOS or Android smartphone! Castle Link is an essential component of customization for all Castle ESCs. While the controllers are plug and play, the benefits of fine tuning your Castle ESC through the Castle Link Programming Suite have only reinforced the sophistication and value of the Castle product line. Not only do you get the ability to adjust many variables to enhance your experience, you have the assurance that firmware updates for future features and improvements for your controller are provided at no cost to you.  Discover just how easily and quickly you can reign in tuning with the release of the Castle B•LINK BLUETOOTH ADAPTER, which will allow most Castle Link compatible products to be programmed via Bluetooth enabled mobile devices using the free application, with firmware updating to be added soon. CASTLE LINK APP FEATURES:The Castle Link App contains all of the same tuning options as the Castle Link USB Programming Suite used on a Windows compatible PC, now with even greater flexibility.  NOTE: All current Castle Creations ESCs, many older units and the BEC 2.0 and BEC Pro are supported, for a complete listing of compatible ESCs and accessories please view the PDF file in the resources tab above. App available for free at the Apple App Store and Google Play.  Features: WIRELESS BLUETOOTH COMMUNICATION allows you to interface with most Castle Link compatible ESCs and accessories to change parameters and update  firmware. DATA LOG VIEWING allows the user to view and download data logs wirelessly, giving you the information needed to fine tune your setup. COMPACT AND LIGHTWEIGHT at 1.20" x .81" x .25" (30.48mm x 20.55mm x 6.55mm) and 0.23oz (6.62g), it can be installed in the vehicle or airframe without significantly increasing model weight. CONVENIENT WATERPROOF DESIGN allows you to quickly adjust settings in the field without disconnecting or disassembling the model. It can stay installed in the model or be easily swapped between models. FREE APP DOWNLOAD is readily available in the Apple App Store or Google Play. Once downloaded it does not require a data connection so it can be used in the most remote of areas and won’t use data. EASY TO USE application can be used with multiple B-Link Bluetooth Adapters or can store model information and allow you to use one adapter on multiple models. PASSCODE PROTECTED with (user-selectable) 4-digit code to prevent unwanted tampering with your settings. SYNC information between multiple devices by creating a free account (requires internet connection to sync database). Specifications: Input Voltage: Minimum: 4.5V - Maximum: 13V Max Continuous Current: 10A Maximum Burst Current: 20A Dimensions (with wires): 7.25" x 0.81" x 0.27" (184.15mm x 20.55mm x 0.27"mm) Dimensions (w/o wires): 1.20" x 0.81" x 0.27" (30.48mm x 20.55mm x 0.27"mm) Weight: 6.62gm / 0.015lbs Needed for Operation: Castle Link App found at Apple Store or Google Play.  This product was added to our catalog on May 1, 2021

Read more less

DYNM3915, Dynamite 3674 4-Pole Brushless Marine Motor (1900kV) This is a replacement Dynamite 1990kV, 3674 4-Pole Brushless Marine Motor. This motor is a replacement for the Pro Boat Sonicwake 36" Deep V Boat. This product was added to our catalog on 03/04/2021

Read more less

KYO32891, Kyosho MR-04 EVO2 Mini-Z N-MM2 Brushless Chassis Set (5600kV) Performance Mini-Z Chassis Roller & Brushless Motor The MR-04EVO2 Mini-Z N-MM2 Brushless Chassis Set (5600kV) represents a significant leap forward in the top-tier MINI-Z series, offering a full model upgrade that pushes the boundaries of performance. Retaining the excellent MR-03 layout while introducing key enhancements, the MR-04EVO2 chassis achieves unparalleled performance improvements. The lower center of gravity (CG) resulting from the lower mounting of AAA batteries enhances stability through corners and elevates both speed and control. This thoughtful chassis design, coupled with the Sensored brushless motor, provides a total balance that takes performance to a higher level, making it a formidable competitor in the high-performance competition mini R/C car category. Quality is evident in the meticulous design and engineering of the MR-04EVO2 chassis. The front suspension improvements, including an updated kingpin-integrated knuckle for enhanced camber stability, showcase a commitment to optimizing every detail. The geometric revisions of the caster and trail contribute to more linear maneuverability, allowing drivers precise control over their vehicles. The inclusion of a ball differential as standard further refines the driving experience, optimizing rotational differences between left and right rear wheels during turns and providing moderate slip action for improved traction. The silver clear anodized finish on aluminum parts not only contributes to durability but also adds a stylish touch that matches the chassis's exceptional performance. What makes the MR-04EVO2 truly special is its adaptability and customization options. The chassis supports both narrow and wide tread settings, allowing enthusiasts to tailor their setup according to body type. Adjustable wheelbase adds another layer of customization, providing flexibility in chassis settings. The included brushless motor, Kyosho Speed House XSpeed 56 (5600kV) ensures the delivery of powerful, smooth and efficient performance! Taking the MR-04EVO2 to another level of dominance in the world of high-performance mini competition R/C cars, solidifying its position as one of the best of the best! NOTE: This is an assembled chassis that still requires additional items to run. See needed to complete list below for a list of items required to complete the model. Features: Powerful Kyosho Speed House XSpeed 56 (5600kV) brushless motor Lower CG design with lower battery mounting positions Significant performance improvements Updated kingpin-integrated knuckle to further improve camber stability Adjustable wheelbase and tread settings Adjustable wheelbase Ball differential included as standard Ball bearings have been changed to 3mm internal diameter for lower rotational resistance Geometric revision of caster and trail Improved linear maneuverability Specifications: Scale: 1/27 Length: 124.5mm Width: 72-76mm Height: 31mm Wheelbase: 98.0mm (LL) Weight: 135.5g Front Tread: 58.5 / 65.0mm Rear Tread: 61.5 / 65.0mm Gear Ratio: 7.3 / 6.3 / 5.5 / 4.9 1 Motor: XSpeed 56 (5600kV) Includes: (1) MR-04EVO2 Mini-Z N-MM2 Brushless Chassis Set w/(5600kV) Motor (1) Electronic speed controller (ESC) 6T / 7T / 8T / 9T Pinion gears Pinion gear tool Wheel wrench Spare wheel nuts Needed to Complete: (1) 2-Channel Transmitter/Receiver system (4) AAA Batteries for Chassis (1) Body (4) Tires (4) Wheels This product was added to our catalog November 22, 2024

Read more less

MOV20920P, Motiv LAUNCH PRO Drag Racing Modified Brushless Motor (2.0T) OVERVIEW The Motiv 30x30 High Voltage Carbon Edition Super Fan features dual ball bearings and is rated to handle 8.4 volts, but will still push good air flow running off of the lower Rx voltage. Included is a MOTIV carbon fan guard to save that precious pinky from imminent annihilation. This product was added to our catalog on August 10, 2021

Read more less

MOV20920P, Motiv LAUNCH PRO Drag Racing Modified Brushless Motor (2.0T) OVERVIEW The Motiv LAUNCH 2.0 Turn PRO Drag Racing Modified Brushless Motor is a 3 phase, 2 pole motor developed specifically for drag racing. Every MOTIV Motor is hand checked, assembled and packaged by a professional in house at their WI, USA office. During this process, every motor component must meet MOTIV requirements before assembly and packaging. Included is a specification check list which is filled out on a motor to motor basis all through the testing and assembly process to ensure the quality of the finished product. Features: Stator: Specially selected stator material for low power loss High quality pure copper wire Emphasis on hand winding for consistency Solder Tabs: Gold plated pure copper tabs for low resistance Internal "Drop Connection" design to ensure low resistance and consistent internal solder joints Rotor: Sintered rotor High quality neodymium magnet material for lasting magnetism Can Assembly: High flow vent holes to allow air flow in and out for lower operating temps Machined all aluminum anodized can, front plate and end bell Infinitely adjustable timing Dual precision ball bearings Overall: Every motor tested in house during the assembly and packaging process Spec/test sheet provided uniquely for every motor to ensure quality Designed to comply with ROAR specifications Lightweight completed design Packaged in reusable cushioned storage container This product was added to our catalog on August 10, 2021

Read more less

MOV20920P, Motiv LAUNCH PRO Drag Racing Modified Brushless Motor (2.0T) OVERVIEW The Motiv 30x30 High Voltage Carbon Edition Super Fan features dual ball bearings and is rated to handle 8.4 volts, but will still push good air flow running off of the lower Rx voltage. Included is a MOTIV carbon fan guard to save that precious pinky from imminent annihilation. This product was added to our catalog on August 10, 2021

Read more less

MOV20920P, Motiv LAUNCH PRO Drag Racing Modified Brushless Motor (2.0T) OVERVIEW This is the Motiv M-CODE "MC4" Pro Tuned 13.5 Turn Spec Brushless Motor. Every MOTIV Motor is hand checked, assembled and packaged by a professional in house at their WI, USA office. During this process, every motor component must meet MOTIV requirements before assembly and packaging. Included is a specification check list which is filled out on a motor to motor basis all through the testing and assembly process to ensure the quality of the finished product. Features: Stator: Specially selected stator material for low power loss High quality pure copper wire Emphasis on hand winding for consistency Solder Tabs: Gold plated pure copper tabs for low resistance Internal "Drop Connection" design to ensure low resistance and consistent internal solder joints Rotor: Sintered rotor High quality neodymium magnet material for lasting magnetism Can Assembly: High flow vent holes to allow air flow in and out for lower operating temps Machined all aluminum anodized can, front plate and end bell Infinitely adjustable timing Dual precision ball bearings Overall: Every motor tested in house during the assembly and packaging process Spec/test sheet provided uniquely for every motor to ensure quality Designed to comply with ROAR specifications Lightweight completed design Packaged in reusable cushioned storage container   This product was added to our catalog on August 10, 2021

Read more less

PRB08029, Veles 29" Brushless Catamaran RTR Product Details In The Box (1) Veles 29 Catamaran Boat (1) Spektrum™ DX2E 2.4GHz Transmitter (1) Spektrum SR310 DSMR 3-Channel Receiver (1) Dynamite® 120A Marine Brushless Marine 2-6S ESC (1) Dynamite Marine Brushless Motor, 2000Kv (1) Spektrum 3KG Plastic Gear Servo (1) User Manual Needed To Complete High-performance LiPo or NiMH battery (Dynamite 11.1V 5000mAh 3S 50C Reaction 2.0 Hardcase LiPo Battery: EC5, DYNB5035H5) LiPo or NiMH battery charger (Spektrum, S2100 AC Smart Charger, 2x100W) (4) AA batteries Features Hand-laid fiberglass composite hull Hand-laid fiberglass canopy Removable composite interior Powerful 2000Kv 6-pole marine motor Adjustable aluminum propeller strut Break-away rudder with water inlet New propeller design Spektrum™ DX2E 2.4GHz transmitter and receiver High-torque waterproof steering servo Water-cooled electronics Overview The Veles 29-inch Catamaran looks as good as it performs. It has much in common with the Blackjack 29, but has some new tricks up its sleeve-including an all-new hull and a 6-pole 2000Kv motor that is more efficient and powerful. On 4S Li-Po, the motor can propel the boat to 45+ miles per hour. With 6S power, this boat can hit speeds of 50+ miles per hour. The Veles 29 has an anodized, inline, adjustable propeller strut, offset rudder with water pick up, and stainless steel propeller. This boat is responsive and predictable, making it easy to drive. Whether this is your first RC watercraft or you've been driving boats for years, you'll love the speed, power and handling of this slick catamaran. Video Overview Hand-laid Fiberglass Composite Hull and Canopy Laid in three layers of fiberglass and hardened with high-strength resin, the hull and canopy are built to last! The hull's stiffness allows it to be more predictable-it deforms far less than heat-molded hulls and can withstand speeds in which most heat-molded hulls would fold. Fiberglass constructed hulls are built for performance just like the real boats you see racing offshore. Optimized Hull Design The new hull design features redesigned, stepped ride pads like real 1:1 catamarans. These steps give the boat a smoother ride along the water and ultimately provide more precise steering responses. The hull's design merges the best features of Pro Boat models such as the Miss Geico and Blackjack 29. The canopy has four thumbscrews that secure the hatch in case of crashes. Removable Injection-Molded Interior Thanks to the interior's composite material, there's no need for an inner wood structure. To remove the interior, simply unbolt it for servicing. Powerful 2000Kv 6-Pole Marine Motor This powerful 36x56 mm motor features the same Kv as the motors of our other 29-inch boats, but offers more speed on less voltage when paired with the new stainless steel propeller included with the boat. You no longer need to run 6S power to get 6S speeds. Adjustable Aluminum Propeller Strut The adjustable aluminum propeller strut lets you completely tune your boat for optimal performance in changing water and wind conditions. The flat bottom on the propeller strut acts like a trim tab and makes adjustments much more precise. With the new propeller strut, even small adjustments go a long way. Break-Away Rudder with Water Inlet The Veles uses a break-away rudder to safeguard the rudder and transom from floating objects or in the event the boat runs on shore. The water inlet helps cool the electronics even at low speeds and increases flow with forward momentum. Spektrum™ DX2E 2.4GHz Transmitter and Receiver The Spektrum DX2E 2.4 radio system and receiver with DSMR protocol provides precision and total control. The DX2E allows you to properly adjust your rudder travel. Other features include low-battery detection and failsafe. High-Torque Waterproof Steering Servo The high-torque steering servo offers peace of mind because the boat will stay in the direction you point it despite tricky water conditions. Product Specifications Approximate Assembly Time No assembly required Battery Sold Separately Beam 10.5 in (266mm) Charger Sold Separately Completion Level Ready-To-Run Drive System Flex Shaft Hull Height Catamaran Hull Material Fiberglass Motor Size 6-pole 2000Kv Motor Type Brushless Product Length 29 in (736mm) Product Weight 5.25 lbs (2380g) Propeller Size 1.7 x 1.6 (43 x 63.5mm) Radio Included Receiver Included Speed Control Included Steering Offset Rudder Trim Scheme Colors White and Silver Decals Type Catamaran

Read more less

PRB08034, Pro Boat Aerotrooper 25-inch Brushless Electric Airboat RTR The Pro Boat Aerotrooper 25-inch Brushless Air Boat can be driven practically anywhere. Even on land! Featuring a 2080kv 480 Brushless outrunner motor with 3-blade airplane-style prop mounted above the hull, you can explore large bodies of water, plant-infested swamps, small grass fields, and even snow and ice. Keeping with the theme, a tactical/military hull scheme with removable guns, molded handrails, and cage add to the scale realism. Plus, the scale cockpit with seat and steering fits most action figures. Injection molded two-piece composite canopies are durable with a secure restraint system keeping all electronics safe during use. LED lights mean the fun doesn’t stop when the sun goes down. Features: Injection molded two-piece composite hull Injection molded composite canopies 2080kv 480 Brushless outrunner motor Dynamite 90 amp brushless ESC with Reverse Scale details LED Lights 1/10 scale metal gear waterproof 9KG servo Composite 3-Blade, molded, pusher propeller 2.4 Transmitter and waterproof receiver Specifications: Approximate Assembly Time: Less than 1 Hour     Beam: 10.5 inches (266.7mm)     Boat Type: Airboat     Completion Level: Ready-To-Run     Drive System: Pusher Prop     Hull Height: 8.75 inches (222.3mm)     Hull Material: Nylon composite     Length: 25 inches (635mm)     Motor Size: 480 Outrunner     Propeller Size: 3 in. x 4 in., 3 blade pusher prop     Radio: Spektrum STX2 2CH Radio     Recommended Battery: 11.1V 5000mAh 3S 50C or 14.8V 5000mAh 4S 50C, EC3 Connector (not included)   Scale: 25 inch     Speed: 20 mph on water, 30 mph on land     Speed Control: 90A BL Marine ESC 2-4     Steering: Rudder     Trimscheme Colors: Black     Weight: 3.9 lbs (1.8 kg) Includes: (1) Pro Boat® Aerotrooper™ 25-Inch Brushless RTR Air Boat (1) Spektrum STX2® 2CH Transmitter (1) Spektrum MRX200 2CH Receiver (1) Pro Boat® 90A Brushless Marine ESC (1) Spektrum 9kg Metal, Waterproof 23T Servo (1) Dynamite 2080KV Outrunner Motor (1) Product Manual Needed to Complete: 3S or 4S 5000mAh 50C Battery with EC3 Connector Appropriate LiPo Battery Charger Needle nose pliers (recommended) Paper towel (recommended) Rubbing alcohol (recommended) Phillips screwdriver: #1, #2 (recommended) Hex drivers: 1.5mm and 2mm (recommended) Clear tape (recommended) Marine grease and application gun (recommended) This product was added to our catalog on April 23, 2021

Read more less

TEKTT2302, Tekin RX8 GEN3 1/8 Competition Brushless ESC Tekin's RX8 GEN3 brings bigger power handling capabilities and increased reliability to 1/8 Scale Racing. The RX8 platform has proven itself to handle the rigors of racing, while providing professional features including a programmable High Voltage BEC, Data Logging Capabilities, Timing Profiles, Voltage Cutoffs for LiPos, HotWire 3.0 Bluetooth Connectivity and more. Utilizing Tekin's D2 Dual Drive Mode Technology, the RX8 runs both Sensored and Sensorless motor drives seamlessly, giving you the best of both worlds. The small footprint makes install on any chassis easy with the option of mounting with included hardware for extra security. Combo the RX8 GEN3 with a Tekin T8 Brushless Motor for 1/8 Scale Buggies and Truggies or a Pro4HD for 4WD Short Course domination! Features: Updated HD Gold-plated Solder Posts for Easy Soldering Updated Adjustable Torque Control Updated Adjustable Throttle and Brake Frequencies Updated HD High Voltage Programmable BEC Ultra-smooth and Precise Throttle and Braking Control Compatible with Brushless and Brushed Motors Easily Access Programming, Anywhere, Anytime Datalogging Capability EZ Access HotWire Programming Port HotWire Interface for Advanced Programming and Updating D2: Dual Drive Mode Technology On-Board Temperature Indicator HDAC: High Density Copper PCB's Sensor Plug for Precise Commutation with all Motors Self Test Diagnostics and Factory Reset Pit Tune Mode DGF2: Digital Glitch Filtering V2 QuickTune Programming One-Touch Radio Calibration Specifications: Controls: Forward/Brake/Reverse Input Voltage: 2S-6S LiPo / 4-16S NiMH-NiCD BEC: 6.0v / 7.4v @ 8amps Motor Limit Brushless Mode: 2S - No Limit; 3S - 4000kV; 4S - 3500kV; 5S - 2200kV; 6S - 2200kV Motor Limit Brushed Mode: No Limit Max Current: 300amps per phase* Burst Current: 1000amps per phase* Timing Profiles: 7 choices (on board) Brushed Modes: FWD Only / FWD-REV / FWD-REV Delay Brushless Modes: FWD Only / FWD-REV / FWD-REV Delay Dimensions: 1.5 x 2.2 x 1.4" / 38 x 55.8 x 35.5mm Weight: 2.7oz / 76.5g Recommended Applications: 1/10 4WD SCT, 1/8 4WD Buggy, 1/8 4WD Truggy, 1/8 4WD Monster Truck, 1/8 4WD Touring Car, 1/8 4WD GT, 1/8 Dirt Oval, 1/10 (and larger) Rock Crawler *Per Manufacturer Specs This product was added to our catalog on December 12, 2021

Read more less

TEKTT2518, Tekin Pro4 HD 4-Pole Brushless 550 Motor w/5mm Shaft (4,300kV) This is the Tekin Pro4 HD 4300kV 4-Pole Brushless Motor. Tekin's Pro4 HD Motor raises the bar in 4wd short course, with the torque and power needed to level the competition. With kV ranges to accommodate 2S, 3S and 4S applications, 1/10 4WD Short Course has never been exposed to this much power! The Pro4 HD's longer 550 can and 4 pole design delivers the off the charts performance gains you need to move your truck to the front of the pack.Features: Designed to be paired with the RX8 Electronic Speed Control 4 Pole 12 Slot Hi-torque 550 Motor Design CNC Machined 6061 T6 Billet Aluminum Heatsink Can Neodymium Sintered Magnets Rebuildable Design High Purity Copper Windings Maximizes Efficiency Precision Engineered for Maximum Energy Conversion Dual-Plug Sensor Wire Harness for use with all sensored systems High RPM ABEC5 Oversized Bearings Specifications:Turns: 1.5DVoltage: 2S - 7.4VkV: 4300Rotor: 18.5mmWeight: 7.8oz / 221gShaft Dimensions: .60x.196" / 15.3x5mmMotor Diameter: 1.4" / 35.8mmMotor Length: 2.5" / 62.5mmBearing Dimensions: Front: 5x14x5mm / Rear: 5x11x5 This product was added to our catalog on December 12, 2021

Read more less

TRA2255, Traxxas 400 High Torque Metal Gear Waterproof Brushless Servo (Red) (High Voltage) The Traxxas 400 High Torque Metal Gear Waterproof Brushless Servo combines maximum steering authority with a long list of high-performance features. The servo utilizes full metal gears, dual ball bearings, and an aluminum center section for added heat dissipation. A cutting edge brushless motor provides 400 ounce-inches of torque for extreme applications.* The High-Torque 400 servo is fully waterproof, not just “water resistant” and drops into most 1/10 Traxxas vehicles for that perfect factory fit. The Power to Perform With over 3 times more torque than the standard #2075 servo, the High-Torque 400 provides noticeably faster turning speed and works great with TSM™ equipped vehicles. Traxxas High-Torque servos are the perfect upgrade for high-demand applications like Unlimited Desert Racer, Slash, Stampede, or almost any 1/10 Traxxas vehicle requiring extreme performance. Replace the E-Revo's dual servos with a single #2255 for lighter weight, more torque, and lightning-quick steering response. Elevate your steering performance to the next level with the High-Torque red 400 servo. Waterproof Not "Water Resistant" Traxxas knows the difference between “water resistant” and waterproof. Traxxas High-Torque servos are completely waterproof to give you the freedom to run when you want, where you want. Power through streams and bogs without fear while trucks with “water resistant” servos are stuck on the sidelines. For TRX-4 Installation The Traxxas High-Torque 400 Red servo represents a huge power upgrade for the TRX-4. When installing this servo, it is required that you use the High-Voltage BEC kit (TRA2262) and a steel servo horn (TRA8247X) is recommended. Installing the BEC is easy with plug and play simplicity. The kit includes a larger receiver box cover to maintain total waterproof integrity and a Y harness for vehicles with LED light kits. NOTE: *Compatible with most Traxxas 1/10 scale electric models Compatible with TRX-4 models using High-Voltage BEC Kit #2262 and #8247X metal servo horn Compatible with Traxxas nitro models using rechargeable 5-cell battery packs Not recommended for X-Maxx Features: Factory fit for drop-in installation into Traxxas Models Fully waterproof, not “water resistant” Compatible with Traxxas Stability Management™ (TSM) 400 oz-in torque at 6.0V 0.15 sec/60° at 6.0V Metal gears Dual ball bearings Brushless motor technology Aluminum center case Specifications: Motor Type: Brushless Operating Voltage: 6.0 - 7.4V DC Speed: 0.15 sec/60° at 6.0V Torque: 400 oz-in at 6.0V Weight: 64g Gears: Metal Output Spline: 25T Case: Plastic top/bottom, anodized aluminum center Controller: Digital This product was added to our catalog on April 12, 2021

Read more less

TRA3481, Traxxas Maxx SLash/Unlimited Desert Racer Brushless Motor (2200Kv) The Traxxas Unlimited Desert Racer Motor is a 4-pole 2200Kv, brushless motor. This is the replacement motor for the UDR. Motor is factory wired with 6.5mm bullet connectors.  Specifications: Can Length: 77.5mm Can Diameter: 41.8mm Total Length: 98.5mm Shaft Length: 21mm Shaft Diameter: 4.99mm This product was added to our catalog on April 16, 2021

Read more less