This a great two in one tool that gives a loud alarm at low voltage and can quickly display battery voltage. Simply plug a 1-8s battery's balance connector into the voltage meter/buzzer, and you will receive an instant readout of the total voltage and an individual reading of each cell. Don't be caught without this battery checker!
Tip: If the buzzers are too loud for you, fill them with a little hot glue to mute it!
Check out our other Battery Chargers and Accessories!
Specifications
Compatible with 1-8S Lipo/Li-ion/LiMn/Li-Fe batteries
Voltage detection precision: +/-0.01V
Low voltage alarm mode for 2S~8S; Adjustable alarm set value range:~2.7~3.8V
Total voltage display range: 0.5V~36V
Includes
1x 1-8S LiPo Battery Checker Voltage Tester w/ Low Voltage Alarm
Disassemble at your own risk, we are not responsible for any damage to your camera!
Plastic injection molded GoPro Lite case from BetaFPV. BEC board is optional and also has an adapter for the BetaFPV ND16 Filter for GoPro Lite
This case and BEC board fit the GoPro HERO6 and GoPro HERO7 Black. But NOT for GoPro HERO8.
Check out all our replacement cam parts & accessories and all our BetaFPV selection!
Features
Plastic injection molded,
Easy assembly
Lightweight
Specifications
Weight: 6.57g
Output: 5V@2A
Voltage: 2-4S
Includes
1x BetaFPV GoPro Lite Case V2 for Naked GoPro
1x BEC Board
Instructions for Assembly
How to Assemble
Step 1: Assemble the BEC board on the GoPro motherboard.
Step 2: Hold the camera lens and the camera board at the same time, be careful when you assemble the board on the case.
Step 3, 4: Screw the GoPro motherboard with the M1.4*5 and M1.4*8screws as shown below
Step 5: Install the light pipe as shown below.
Step 6: Install the back case, and screw the board with M1.4*8 screws as shown below.
How to Disassemble GoPro HERO6 Black
Special thanks to JONAH BLAESER who provided the method of disassembling GoPro HERO6 Black. If you are interested, please check the link to know the specific steps to make your own naked GoPro.
GoPro HERO6 Black Disassembly Guide
We also provided the method of disassembling GoPro HERO8 Black. If you are interested, please check the link.
GoPro HERO8 Black Disassembly Guide
Note: Do this at your own risk. You will lose your GoPro’s warranty and you may end up bricking the camera if something goes wrong. This guide is not authorized by GoPro and your camera is not guaranteed to work afterward.
These big boys are ready to to rock your 8"+ props! This KV is ideal for 5-6S macro builds, see the "Test Data" tab for more info.
Check out our huge selection of motors and all our Brotherhobby gear!
Features
Incredibly powerful, yet smooth running
Extremely durable due to quality components
Lightweight (for their size!)
Specifications
KV: 1115KV
Input Voltage: 5-8S
Configuration: 12N14P
Bell cap: Al 7075
Base casing: Al 7075
Stator: 0.2mm Kawasaki silicon steel
Bearings: Japanese NMB 12X6X4
Rotor: N52H arc magnets
Shaft: Titanium Alloy hollow shaft
Prop Adapter Shaft Thread: M5
Wire AWG: 18AWG 25cm length
Bolt Pattern: M3 (19X19mm)
Weight: 76.5g with 25cm SR wires
Includes
1x BrotherHobby Avenger V3 2812 1115Kv Motor
This is a beast of a motor, lightweight and durable.
Available in multiple Kv options.
Check out our vast motor selection and all our Brotherhobby gear!
Specifications
No.of Cells(Lipo): 5-8S
Configuration: 12N14P
Stator: 0.2mm silicon steel
Prop Adapter Shaft Thread: M5
Shaft: Titanium Alloy hollow shaft
Bolt Pattern: M3 (19X19mm)
Bearings: Japanese NMB 12X6X4
Rotor: N52H arc magnets
Weight: 110g with 25cm SR wires
Wire AWG: 18AWG 25cm length
Bell cap: Al 7075
Base casing: Al 7075
Includes
1x BrotherHobby Tornado T5 3115 Pro 1050Kv Motor
CellMeter 8 V2.0 is one sweet battery checker! With it you can quickly and easily check a battery's voltage, balance a battery, or discharge a battery.
A great way to keep up with the info of your LiPo Batteries!
Check out our other Battery Chargers and Accessories!
Features
High visibility LCD display screen
Port for balance plug for up to 8 cell Lipo, LiFe, or Li-Ion batteries
Can be used as Servo tester to test standard and narrow servo.
Port for discharge plug of NiMh/NiCd batteries
Can be used to check the battery voltage of Lithium batteries including Lipo, LiFe, Li-Ion, as well as NiMH and NiCd batteries.
Measure the voltage of both individual cells and full battery voltage, and can also indicate the highest voltage cell, lowest voltage cell and difference
Specifications
Discharge Current: 1A
Balance Current: 1A
Battery Voltage Test Precision: 0.001V
Battery Type: Can test Li-Po/Li-lon/Li-Fe(2-8S),NiCd/NiMH(4-8S) battery
Servo Test Range: 1000-2000us or 500-2500us
Includes
1x CellMeter 8 V2 2-8S Battery Checker
CLRacing is well trusted in the industry and the CLRacing F7 V2.2 45A 2-6S 30x30 Stack/Combo will show you exactly why. Durable, feature rich, and easy to solder to. Check out the specs below!
This F7 FC and 45A 4in1 ESC are available separately as well!
Choose either dual or single gyro version.
Check out all our 30x30 Stacks and Combos and our full range of CLRacing products!
Specifications
FC
Input Voltage: 2-8S
MCU: STM32F722RET6216MHz
IMU: Choose Dual ICM20602 or Single MPU6000
OSD: Yes
BlackBox: 32MB
UARTS: 6
ESC Connections: 6
Reverse Polarity Protection: Yes
Camera Control: Yes
BEC: 5V/1.5A, 3.3V/250mA
Buzzer Pads: Yes
LED Pads: Yes
Mounting Dimensions: 30x30
ESC
Input Voltage: 2-6S
Max. Continuous Current: 45A
Max. Burst Current: 55A
Firmware: BLHeli_32
Support: Dshot300-1200/MultiShot/OneShot/ProShot/PMW
Current Sensor: Yes
Current Sensor Scale: 250
Dimensions 43.5mm x 46.5mm
Mounting Dimesions: 30.5x30.5mm Φ4mm
Weight: 13.5g
Includes
1x CLRacing F7 V2.2 30x30 Flight Controller
1x CLRacing 45A V2 32bit 30x30 4in1 ESC
1x Wiring & Accessory Kit
CSE010-0165-00, Castle Creations Mamba Monster X 8S 1/6 Brushless ESC
The Castle Creations Mamba Monster X 8S 1/6 Brushless ESC features CRYO-DRIVE™ - Castle’s latest break-through technology. CRYO-DRIVE minimizes the amount of time the ESC’s electrical components spend generating heat. This proprietary software advancement works in parallel with a unique open housing design and a forged elliptical fin heatsink to allow increased directional airflow to cool critical components. Combine this with a high speed 40mm fan and you have a design that maximizes airflow through the system, taking thermal performance to the next level. The results are cooler ESC temperatures, increased runtime and more power handling.
Mamba Monster X 8S is designed for 1/6 scale vehicles weighing up to 25 lbs. with up to 8S LiPo.
Compatible models include the Traxxas X-Maxx & Unlimited Desert Racer; Arrma Kraton 8s & Limitless; Losi Super Rock Rey & Audi R8; Redcat Shredder.
Features:
Input voltage range 2S-8S LiPo
Sensored, Sensorless and SmartSense™ running modes
Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V)
Premium forged heatsink with elliptical fins for superior airflow and increased heat dissipation
Oversized factory equipped thermally controlled 40mm fan ? Waterproof design for all weather conditions
ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the components and promote efficient heat transfer
Data-logging capability to capture and record performance data from your vehicle
Auxiliary wire functionality for “on the-fly” adjustments using your transmitter
Audible alerts for easy diagnosis of possible issues such as motor over-temperature and low voltage cutoff
Convenient transmitter programming for six adjustable settings such as cutoff voltage and drag brake
Easily tune and update ESC with USB and Bluetooth™ programming options
Castle Link USB programming kit (coupon included with purchase)
Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store
Proudly designed and manufactured in Olathe, Kansas USA and backed by Castle Creations’ 1 year warranty
Specifications:
Application guidelines: 1:6 scale RC hobby vehicles weighing up to 25 lbs
Running Modes: Sensored, Sensorless and SmartSense™ (when paired with a Castle 4-POLE 12SLOT sensored motor)
Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V
BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. Or 8.0V (8A Peak), default 5.5V
Operating environment: Waterproof design enables use in nearly any environment
Brake: Proportional
Reversible: Yes, but may be disabled for racing
On /off switch: Yes, waterproof
Cooling fan: Yes, factory equipped (40mm), fully removable (See Product Use Statements for more info)
Size: L x W x H 69.5mm x 54.1mm x 47mm
Weight (w/wires): 5.75 oz. (163 grams)
Connector type: 6.5mm female bullets for motor connection
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately).
Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters.
This product was added to our catalog on May 14, 2021
CSE010-0165-01, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/2028 Sensored Motor (800kV)
The Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo with 2028 Sensored Motor is a great way to take your build to the next level with Castle’s cutting edge sensored large scale brushless power. The MAMBA MONSTER X 8S COMBO is ready to power any R/C vehicle weighing up to 25lbs, and running all the way up to 8S LiPo. This motor and ESC combo is designed for heavy, high speed rigs, and you'll experience smooth low-end control, without sacrificing power, punch, or speed.
The MAMBA MONSTER X 8S utilizes Castle’s breakthrough technology, CRYO-DRIVE. By reducing the rate at which the ESC heats up and removing heat more efficiently, your setup will be able to handle higher gear ratios, in heavier vehicles, with longer runs. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 40mm cooling fan and a forged elliptical fin heatsink, the design maximizes airflow throughout the system, taking thermal performance to a whole new level.
The ESC was designed with a robust aluminum casing, and the epoxy potting guarantees protection around the circuitry and ensures all-weather use. Mamba Monster X 8S is a beast, ready to take on the harshest of environments and still perform. You can easily optimize the ESC for any driving condition, from rugged terrain to smooth pavement to the perils of rock and gravel. Create, save and download setup profiles through the Castle Link Programming Suite on your Windows™ PC, or wirelessly with the convenience of the new B-Link™ Bluetooth™ Adapter and Castle Link app for Android or iOS.
When paired with the Castle sensored 2028-800KV motor, users with heavy, high power rigs will experience controllable low-end control without sacrificing power, punch or speed. SmartSense™ mode uses the motor’s sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is spinning, it seamlessly transitions to Castle’s ultra-efficient sensorless mode. You’ll put more power to the ground, where it should be, instead of wasting it through raw heat and RPMs.
NOTE: This is not a direct replacement to the Mamba XLX. The XLX still handles rawer full throttle power in the most extreme setups.
Features:
ESC:
Input Voltage Range 2S-8S LiPo
Sensorless, Sensored and SmartSense™ Running Modes
Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V)
CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs
ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the electronics and promote efficient heat transfer
Premium forged heatsink with elliptical fins for superior air flow and increased heat dissipation
Oversized factory equipped thermally controlled 40MM cooling fan
Compatible with S.BUS2 Telemetry Link and Futaba T4PX and T7PX transmitters
Waterproof design for all weather conditions
Data logging capability to capture and record performance data from your vehicle
Auxiliary wire functionality for "on-the-fly" adjustments using your transmitter
Audible alerts for easy diagnosis of common issues such as motor-over-temperature and low-voltage cutoff
Convenient transmitter programming for six common adjustable settings including cutoff voltage and drag brake
Easily tune and update ESC with USB and Bluetooth™ programming options
Castle Link USB programming kit (coupon included with purchase)
Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store
Proudly designed and manufactured in Olathe, KS USA and backed by Castle Creations' 1-year warranty
Motor:
The 2028 Extreme can easily run in the 10 horsepower range (Burst power output for duration's typical of vehicle acceleration.)
Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode.
High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions.
Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible.
Proprietary winding techniques allow Castle Creations to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor.
Dual sensor ports to ensure optimal installation in your large-scale vehicle.
Updated modern and sleek design that looks as cool as it performs.
Specifications:
ESC:
Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V
BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V
Operating Environment: Waterproof* design allows for use in nearly any environment.
Brake: Proportional
Reversible: Yes, but may be disabled for racing.
On/Off Switch: Yes, waterproof
Cooling Fan: Yes, factory equipped (40MM), fully removable** (See Product Use Statements below)
Size: L x W x H 69.5mm x 54.1mm x 47mm
Weight (with no battery connector): 5.75 oz. (163 grams)
Connectors: 6.5mm female bullets for motor connection
Motor:
Input Voltage Range: 12S MAX
Kv: 800
Max. RPM: 45,000
Minimum Input Voltage: 3S
Maximum Input Voltage: 12S
Sensored Capable: Yes
Can Length: 4.4" (113.2mm)
Can Diameter: 2.2" (57mm)
Weight (w/wires): 44 oz./1.25kg
Shaft Size: Length: 30mm
Diameter: 8mm
Mounting Hole Specifications: 4mm holes @ 30mm spacing.
Cooling Fan: Available, but not included. See 011-0019-00 here.
Connectors: 8.0mm male connectors
Recommended ESC: Mamba XL X
Running modes: Sensorless and Sensored
Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs.
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately).
Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters.
Product Use Statements:
Recommended battery capacity for 1:6th scale vehicles is 5000mah. Castle recommends using 50C continuous discharge or higher LiPo batteries.
Surge ratings should never be used to determine a pack’s suitability for a brushless application.
Castle recommends a high current connector designed for high-powered electric systems, rated for 100+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors.
Applying voltages higher than 33.6V will cause irreparable damage to ESC.
Although Mamba Monster X 8S is waterproof, it is NOT intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt.
The cooling fan must be removed prior to driving in wet conditions. *Fan is not waterproof.
Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the motor or ESC.
The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the Running & Maintaining document in the resources tab above for info on running and maintaining motors in wet environments.
Application Guidelines: Mamba Monster X 8S and 2028-800Kv motor is intended for use in 1:6 scale vehicles weighing up to 25 lbs. and up to 8S LiPo. Vehicle Examples: Traxxas™ X-Maxx & Unlimited Desert Racer; Arrma™ Kraton 8s & Limitless; Losi™ Super Rock Rey & Audi R8; Redcat™ Shredder (optional motor mount and modifications may be necessary to install motor).
Includes:
Mamba Monster X 8S ESC
4-POLE Sensored 2028-800KV Motor
Castle Sensor Harness Adapter (installed)
250mm Sensor Wire
Mamba Decals
Coupon for free Castle Link USB
ESC Quick Start Guide
Motor Quick Start Guide
This product was added to our catalog on April 4, 2021
CSE010016502, Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo w/1717 Sensored Motor (1650kV)
COMPATIBILITY:
Arrma Felony 6S BLX
Arrma Infraction 6S BLX
Arrma Infraction V2 6S BLX
Arrma Limitless
Arrma Outcast 8S BLX
The Castle Creations Mamba Monster X 8S 1/6 ESC/Motor Combo with 1717 Sensored Motor is an incredible combo developed specifically for high voltage large scale applications. The MAMBA MONSTER X 8S ESC utilizes Castle’s proprietary CRYO-DRIVE technology helping to reduce the heat generated, and remove heat more efficiently. These software advancements work in parallel with a unique open housing design to allow increased directional airflow to cool critical components. With the integration of a 40mm cooling fan and a forged elliptical fin heatsink, the design maximizes airflow throughout the system, taking thermal performance to a level never seen before.
Mamba Monster X 8S is a workhorse that will dominate in the harshest of environments. Designed with durability in mind, this ESC features a robust aluminum case, combined with epoxy potting helps to guarantee protection around the circuitry, as well as allowing all-weather use. You can easily optimize the ESC for any driving condition - rugged terrain, smooth pavement, or rock and gravel, the MMX8S can handle it all. Plus, the Castle Link Programming Suite will allow the user to create, save and download setup profiles using a Windows™ PC, or wirelessly with the convenience of the B-Link™ Bluetooth™ Adapter and Castle Link app for Android or iOS. The MMX8S also allows tuning on-the-fly via the Auxiliary wire, allowing access to programming parameters such as Torque Control, Max Brake or Rock Race Mode, further optimizing your vehicle for any racing or bashing application you can imagine!
When paired with the included Castle 1717-1650KV sensored motor, heavy, high speed rigs will experience controllable low-end control without sacrificing power, punch or speed. This motor is a blast from the past with the added benefit of sensored capabilities! It is the perfect upgrade for any 1/6th scale vehicles weighing up to 20 lbs and running up to 8s LiPo; it is also a great upgrade for drivers looking for a reliable, high torque 8s motor for their 1/8th scale vehicles! The Castle 1717 1650KV sensored motor features an improved 4-POLE 12-SLOT design that boasts exceptional EFFICIENCY and produces LESS HEAT. SmartSense™ mode uses the motor’s sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is spinning, it seamlessly transitions to Castle’s ultra-efficient sensorless mode. You’ll put more power to the ground, where it should be, instead of wasting it through raw heat and RPMs.
Application Guidelines: Mamba Monster X 8S and 1717-1650Kv motor is intended for use in 1:6 scale vehicles weighing up to 20 lbs. and running up to 8S LiPo. Also a great upgrade for heavier 1/8th vehicles.
Features:
ESC:
Input Voltage Range 2S-8S LiPo
Sensorless, Sensored and SmartSense™ Running Modes
Powerful Integrated 8A Peak Adjustable BEC (5.25V-8.0V)
CRYO-DRIVE™ Technology minimizes the amount of time the ESC’s electrical components spend generating heat, resulting in improved thermal performance during partial throttle operation where the majority of driving occurs
ESC is housed in a rugged CNC aluminum case and potted in waterproof epoxy to protect the electronics and promote efficient heat transfer
Premium forged heatsink with elliptical fins for superior air flow and increased heat dissipation
Oversized factory equipped thermally controlled 40MM cooling fan
Compatible with S.BUS2 Telemetry Link and Futaba T4PX and T7PX transmitters
Waterproof design for all weather conditions
Data logging capability to capture and record performance data from your vehicle
Auxiliary wire functionality for "on-the-fly" adjustments using your transmitter
Audible alerts for easy diagnosis of common issues such as motor-over-temperature and low-voltage cutoff
Convenient transmitter programming for six common adjustable settings including cutoff voltage and drag brake
Easily tune and update ESC with USB and Bluetooth™ programming options
Castle Link USB programming kit (coupon included with purchase)
Optional smartphone-based programming with the B-LINK™ Bluetooth Adapter (sold separately) and Castle Link app available on Google Play or Apple App Store
Proudly designed and manufactured in Olathe, KS USA and backed by Castle Creations' 1-year warranty
Motor:
4-POLE 12-SLOT sensored design that boasts exceptional efficiency and produces less heat
Proprietary stator winding produces low internal resistance for a cooler running motor
Oversized NMB bearings and vibration dampening system ensure the longest possible bearing life
High-strength, high-temperature grade neodymium sintered magnets combined with high-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions and high RPMs
Specifications:
ESC:
Input Voltage Range: MIN: 2S LiPo , MAX: 8S LiPo 33.6V
BEC Specifications: Adjustable: 5.5V, 6.0V, 7.5V. or 8.0V (8A Peak), default 5.5V
Operating Environment: Waterproof* design allows for use in nearly any environment.
Brake: Proportional
Reversible: Yes, but may be disabled for racing.
On/Off Switch: Yes, waterproof
Cooling Fan: Yes, factory equipped (40MM), fully removable** (see Product Use Statements below)
Size: L x W x H 69.5mm x 54.1mm x 47mm
Weight (with no battery connector): 5.75 oz. (163 grams)
Connectors: 6.5mm female bullets for motor connection.
Items Needed for Operation: A high current connector designed for high-powered electric systems, rated for 120+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors, soldered to the battery leads.
Programmability: Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Link included) and freely downloadable Castle Link Windows™ software, or the Castle Link iOS® or Android® app with B-LINK™ Bluetooth™ Adapter (sold separately).
Telemetry Link Capable: Yes, with Castle Creations Telemetry Link for S.BUS2 and Futaba T4PX and T7PX transmitters.
Motor:
Input Voltage Range: 3S-8S LiPo
Kv: 1650
Max. RPM: 56,000
Size: Length: 3.35" (85.1mm) Diameter: 1.87" (47.6mm)
Weight (w/wires): 21.08oz. /597.6g
Shaft Diameter: 5mm
Mounting Hole Specifications: M3 and M4@25.4mm (1.0") Diameter
Cooling Fan: Not available
Connectors: 6.5mm male connectors
Application Guidelines: Ideal for vehicles up to 20lbs running 6s – 8s LiPo. Examples include Losi LST2-E; Arrma™: Limitless™, Typhon™ 6s, Infraction™, Talion™ 6s; Traxxas: E-Maxx™, E-Revo™, UDR™, Summit™; Redcat Shredder™
ESC Product Use Statements:
Recommended battery capacity for 1:6th scale vehicles is 5000mah. We recommend using 50C continuous discharge or higher LiPo batteries.
Surge ratings should never be used to determine a pack’s suitability for a brushless application.
Castle recommends a high current connector designed for high-powered electric systems, rated for 120+ amps, such as Castle CC Bullet 6.5mm, CC Bullet 8.0mm, or 6.5mm Polarized Castle Connectors.
Applying voltages higher than 33.6V will cause irreparable damage to ESC.
Although Mamba Monster X 8S is waterproof, it is not intended for operation while completely submerged in liquid. Always rinse the ESC with clean water after exposure to corrosives or dirt.
The ESC cooling fan must be removed prior to driving in wet conditions. It is not waterproof.
Tech Notes:
This motor includes 10AWG wire and 6.5mm connectors for use specifically this ESC/Motor combo.
Running modes: SMARTSENSE™, Sensored, Sensorless with Castle sensored capable ESCs.
Water Resistant Design: The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommended applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to this document for running and maintaining motors in wet environments.
Includes:
Mamba Monster X 8S ESC
4-POLE Sensored 1717-1650KV Motor
Castle Sensor Harness Adapter
200mm Sensor Wire
Mamba Decals
Coupon for free Castle Link USB
ESC Quick Start Guide
Motor Quick Start Guide
This product was added to our catalog on June 23, 2021
FETtec has released a 4-In-1 8S 65A DShot 2400 ESC to complement the FETtec Flight Controllers and KISS Flight Controllers. With full sine wave control and all the latest features, this is the perfect ESC to pair with the new flight controller.
Check out all our KISS compatible gear, and everything FETtec!
Features
No more capacitors close to the mounting holes
Specifications
Active current limiting @ 65A
Input voltage: 3S-8S
High quality 40V MOSFETs
STM32G071 @ 64MHz
128 kHz Motor PWM
Full sine wave control
Soldering holes for up to 5 additional capacitors
KISS FC Passthrough
Betaflight Passthrough (available in 4.1)
Automatic input signal detection:Dshot 300-2400,PWM,OneShot 42/125,OneWire BUS with up to 8kHz looptime (one cable for all Motorsignals and Telemetry),S2M
Firmware:
New FETtec Firmware
FETtec Configurator for updated, configuration and telemetry. Standalone for MacOS, Windows 32 & 64 bit and Chrome Plugin
FETtec 4in1 ESC 65A Manual
FETtec Configurator
Includes
1x FETtec 65A 3-6S 30x30 4in1 ESC
The Foxeer H7 Mini X8 20x20 Flight Controller offers reliable performance with its dual BECs and MPU 6000 gyro. It's capable of operating on 4-8S batteries and boasts a barometer for improved stability and altitude control, making it a great choice for drone enthusiasts.
Included with this Flight Controller is an integrated 5V/10V dual BEC!
Check out our 20x20 FCs, as well as Foxeer Collection!
Specifications
Model: Foxeer H7
CPU: STM32H743
Gyro: MPU6000
Barometer: DPS310
Power Supply: 4-8S Lipo
BEC Output: DC5V/2A; DC10V/2A
OSD: BF OSD
Black Box: 16M Flash Memory
UART: 6 Sets+Rx8
ESC Telemetry: RX8
Buzzer: Yes
Smart Audio: Yes
LED: 1 Set 2812 LED
USB: Type-C
Servo: S1,S2
X8: Supported
Firmware(BetaFlight): FOXEERH743
Size: 30X31mm
Mounting Hole: 20 x 20mm, Φ4mm
Weight(g): 5.6g
Working Temperature: -20℃ ~ +55℃
Working Humidity: 20～95%
Storage Temperature: -20℃ ~ +70℃
Includes
1x Foxeer H743 Mini X8 4-8S 20x20 Dual BEC Barometer Flight Controller - MPU6000
4x Rubbers Columns
The Foxeer H7 is an advanced and reliable 4-8S flight controller with dual built-in BECs and a barometer. It features a fast and powerful MPU6000 processor to provide accurate and consistent performance with less vibration in flight. Enjoy worry-free flying with this top-class controller.
Check out our 30x30 Flight Controllers as well as Foxeer Collection!
Features
5V/10V Dual BEC
MPU6000 32K Flash Rate
Plug & Play with Foxeer cameras
Specifications
Model: Foxeer H7
CPU: FOXEERH743
Gyro: MPU6000
Barometer: DPS310
Power Supply: 4-8S Lipo
BEC Output: 3.3V/0.5A;DC5V/2A;DC10V/2A
OSD: BF OSD
Black Box: 16M Flash Memory
UART: 6 Sets+Rx8
ESC Telemetry: RX8
Buzzer: Yes
Connector: DJI/HDZero
Smart Audio: Yes
LED: 1 Set 2812 LED
USB: Type-C
Servo: S1,S2
X8: Supported
Firmware(BetaFlight): FOXEERH743
Size: 37X37mm
Mounting Hole: 30.5 x 30.5mm, Φ4mm
Weight(g): 7.8g
Working Temperature: -20℃ ~ +55℃
Working Humidity: 20～95%
Storage Temperature: -20℃ ~ +70℃
X8 Setup CLI
X8 Setup CLI
Includes
1x Foxeer H743 X8 4-8S 30x30 Dual BEC Barometer Flight Controller - MPU6000
4x M3 Grommets
1x Cable
The Foxeer Reaper F4 128K is the next evolution of the Reaper ESC series. With its low heat generation and high-quality mosfets, this new version has a smoother flight, with fewer desyncs.
Check out the rest of our 30x30 ESCs, as well as the rest of our Foxeer offerings!
Specifications
Input Voltage: 3-8S LiPo
Max. Continuous Current: 65A
Max Burst Current: 100A
Telemetry: Yes
Firmware: BLHeli_32
Target: FOXEER_Reaper4IN1_F4_65A_128_Multi_32_9
Input Signal: DShot 150/300/600/1200/MultiShot/OneShot
BEC: No
Mounting Pattern: 30x30mm M3
Dimensions: 42.5x42.5mm
Weight: 14.8g
Includes
1x Foxeer Reaper F4 128K 32Bit 65A 3-8S 30x30 4in1 ESC
Wiring Diagram
We've come to expect the best out of Foxeer and the Foxeer Reaper series is their flagship series with high-quality electronics. The Foxeer Reaper F4 Mini ESC is precisely what we come to expect out of our ESCs. Fewer desyncs thanks to the powerful F4 chip. Bigger, high-quality MOSFETs, super smooth flights and supports input voltage up to 40V. It's no wonder why Foxeer is a leader in the industry with their excellent Reaper series.
Check out the rest of our 20x20 ESCs, as well as the rest of our Foxeer offerings!
Features
3-8S LiPo Compatibility
60 Amperage
F4 Processor
Specifications
Firmware: FOXEER_ReaperM4IN1_F4_60A_128_Multi_32_9
Continuous /Burst Current: 60Ax4 / 100Ax4
Input Voltage: DC 9V~40V (3-8S Lipo)
BEC: No
Telemetry: Supported
ESC Programming: BLHeli32
Current Scaling: 70
Input Signal: DShot 150/ 300/ 600/ 1200 /MultiShot/ OneShot etc.
Working Temperature: -20℃ ~ +55℃
Working Humidity: 20～95%
Storage Temperature: -20℃ ~ +70℃
Mounting Hole: 20×20mm, Φ4mm/ M3
Dimension: 40.5×40×5.5mm
Weight: 13.5g
Includes
1x Foxeer Reaper F4 32bit 60A 3-8S 20x20 4in1 ESC
The 2809 is a great size because of it's proportion of width to height providing good permanent magnetic flux, adequate stator heat dissipation, good efficiency, good motor weight and excellent low and high rpm control for typical 7-8" loads on 6S with it's 1300kv.
This motor is built with the latest components RCinpower has to offer and parts we've found to perform well. Various adjustments and quality of life improvements include bell durability design, bearing accessibility, flush mounting, magnet heat dissipation and other minor details.
Check out our other motors, and all our FPVCycle selection!
Specifications
Weight: 53g with 20cm 18awg wire
KV: 1300
Configuration: 12N14P
Input Voltage: 6-8S
N52H arc magnets
260℃ enamel copper wire
0.2mm laminations
Titanium Alloy hollow shaft
Japanese NMB 13x6x5mm bearings
Wire: 18AWG 20cm length
Material: 7075 Aluminum
M5 Prop shaft
Motor Mounting: M3 19X19mm flush mount base
Includes
1x FPV Cycle 28mm 1300Kv Motor
All batteries must be shipped by a ground shipping method.
Experience superior power and performance with the Gaoneng GNB 1100mAh 29.6V 8S 120C Lipo Battery. Including an XT60 connector ensures a secure connection, delivering reliable and consistent power.
Check out the all our batteries and our selection of Gaoneng Products!
Specifications
Capacity: 1100mAh
Cell Configuration: 8S1P
Continuous Rate: 120C Continuous
Dimensions: 35x53x80mm
Discharge Lead: 75mm, XT60
Balance Lead: 35mm, JST-XH
Weight: 255g (+/- 1%)
Includes
1x Gaoneng 29.6V 8S 1100mAh 120C LiPo Battery - XT60
The HAKRC HK3220 2-8S BLHELI_32 60A 4in1 20x20 ESC is an advanced ESC featuring a AT32F421 main control chip with operating frequency of up to 128MHz, Japan imported MOS and 3-in-1 IC driver FD6288Q driver, imported Murata capacitors, 8-layer 2-ounce copper PCB, hardware PWM drives, Damped Light technology and Active Freewheeling technology for smoother throttle response, regenerative braking and power recycling.
Check out the rest of our 20x20 ESCs, as well as HAKRC products for sale at RaceDayQuads!
Features
PCB adopts high-end 8-layer 2oZ thickened copper skin, which has stronger overcurrent capability and good heat dissipation.
MOS adopts imported high current resistance MOS, long life with strong load capacity.
Adopt industrial grade LDO, high temperature resistance.
Using 40 50V high-quality Japanese Murata capacitors, strong filtering performance
PWM frequency up to 128k, high frequency for higher throttleRuns smoother.
Specifications
ESC firmware: HAKRC_AT4G_Multi_32.9 Hex
Protocol support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-8S Lipo
Continuous current: 60A
Peak current: 70A
Size: 34 x 42mm (20mm-20mm mounting hole)
Product net weight: 11g
Includes
1x HAKRC HK3220 BLHELI_32Bit 60A 2-8S 20x20 4in1 ESC
1x XT60 Connector
1x 12AWG 6cm Power Cable
1x 35V 470uF Capacitor
1x 8Pin JST ESC to FC cable
4x M3 Grommets.
4x M2 Grommets
The Kakute F4 V2.4 is an 8S Flight Controller that has everything you need, with plug-and-play DJI O3 HD camera, 4in1 ESC ports, barometer, OSD, 5x UARTs, logging & onboard flash storage, plus 5V & 9V/3A BEC. DJI HD ready - just plug it in & the 9V/A regulator will power your HD transmitter, like DJI O3 Air Unit & Caddx Vista. There are LED & buzzer pad, I2C pad (SDA & SCL) for external GPS/Magnetometers
Check out our other 30x30 flight controllers and the rest of our HolyBro selection!
Specifications
MCU: STM32F405
IMU: MPU6000
Barometer: BMP280
OSD: AT7456E
5x UARTs (1,3,4,4,6,7)
128 Mbit Dataflash chip
Battery input voltage: 2-8S
BEC 9V/3A - Optimized for DJI O3 Air unit
BEC 5V/2A
7x PWM Outputs (6 Motor Output, 1 LED)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire, ESLR).
Mounting: 30 x 30mm, Φ4mm hole with M3 Grommets
Dimension: 37x37mm
Weight: 7g
JST-SH1.0_8pin port (For 4in1 ESCs)
JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX)
Includes
1x Holybro Kakute F4 HD V2.4 2-8S 30x30 Flight Controller - MP6000
1x Wiring Kit
Wiring Diagram
The Kakute F4 V2.4 is ready for DJI HD. Easily plug in and power your HD video transmitter (like DJI O3 Air Unit & Caddx Vista) with its on-board 9V/A regulator, plus 5 dedicated UARTs w/inversion for peripherals. This stack comes with a barometer, plus LED/buzzer pad & I2C for external GPS/Magnetometers. The Tekko32 is the first 4in1 ESC, featuring the powerful F4 MCU @150Mhz, giving you smooth control & fast response, 4~6S & BLHeli32 for 30x30 stack/combo. This stack will come with an Atlatl HV V2 800mW VTX that is compatible with all major FPV receivers.
Check out all our 30x30 Stacks and the rest of our HolyBro selection!
Features
Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.
MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.
LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.
Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.
Standard 36mm form factor allows you to mount the Atlatl directly on your flight controller stack.
New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
PWM Frequency: 16k to 96k
Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.
Specifications
Holybro Kakute F4 HD V2.4 2-8S 30x30 Flight Controller
MCU: STM32F405
IMU: MPU6000
Barometer: BMP280
OSD: AT7456E
5x UARTs (1,3,4,4,6,7)
128 Mbit Dataflash chip
Battery input voltage: 2-8S
BEC 9V/3A - Optimized for DJI O3 Air unit
BEC 5V/2A
7x PWM Outputs (6 Motor Output, 1 LED)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire, ESLR).
Mounting: 30 x 30mm, Φ4mm hole with M3 Grommets
Dimension: 37x37mm
Weight: 7g
JST-SH1.0_8pin port (For 4in1 ESCs)
JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX)
Tekko32 F4 4in1 50A ESC
Continuous Current: 50A x4
Burst Current: 60A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 120 (V1.9 Version)
Dimensions: 48x37x6mm / Weight: 13.8g
Mounting holes: M4 30.5x30.5mm (M3 grommets included)
Atlatl HV V2
Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
Audio: 6.5 MHz Mono
Protocol smart audio 2.0
Antenna Connector: MMCX
Input Voltage: 7 to 28 volts (2-6S LiPo) with an absolute maximum 42 volts
Dimensions: 35x25x7mm (Includes USB height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 9.3g
Includes
1x Holybro Kakute F4 HD V2.4 4-6S 30x30 Stack/Combo (F405 FC/ 50A F4 32bit 4in1 ESC & Atlatl HV V2 800mW VTX)
1x Wiring Kit
Wiring Diagram
The Kakute F4 V2.4 is ready for DJI HD. Easily plug in and power your HD video transmitter (like DJI O3 Air Unit & Caddx Vista) with its on-board 9V/A regulator, plus 5 dedicated UARTs w/inversion for peripherals. This stack comes with a barometer, plus LED/buzzer pad & I2C for external GPS/Magnetometers. The Tekko32 is the first 4in1 ESC, featuring the powerful F4 MCU @150Mhz, giving you smooth control & fast response, 4~6S & BLHeli32 for 30x30 stack/combo.
Check out all our 30x30 Stacks and the rest of our HolyBro selection!
Features
New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
PWM Frequency: 16k to 96k
Separate drive & control circuit, this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.
Specifications
Holybro Kakute F4 HD V2.4 2-8S 30x30 Flight Controller
MCU: STM32F405
IMU: MPU6000
Barometer: BMP280
OSD: AT7456E
5x UARTs (1,3,4,4,6,7)
128 Mbit Dataflash chip
Battery input voltage: 2-8S
BEC 9V/3A - Optimized for DJI O3 Air unit
BEC 5V/2A
7x PWM Outputs (6 Motor Output, 1 LED)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire, ESLR).
Mounting: 30 x 30mm, Φ4mm hole with M3 Grommets
Dimension: 37x37mm
Weight: 7g
JST-SH1.0_8pin port (For 4in1 ESCs)
JST-SH1.0_6pin port (For DJI/Caddx HD System and other VTX)
Tekko32 F4 4in1 50A ESC
Continuous Current: 50A x4
Burst Current: 60A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 120 (V1.9 Version)
Dimensions: 48x37x6mm / Weight: 13.8g
Mounting holes: M4 30.5x30.5mm (M3 grommets included)
Includes
1x Holybro Kakute F4 HD V2.4 4-6S 30x30 Stack/Combo (F405 FC/ 50A F4 32bit 4in1 ESC)
1x Wiring Kit
Wiring Diagram
The 8S capable Kakute H7 boasts Bluetooth, dual 4in1 ESC ports, HD plug, barometer, OSD, 6 UARTs, MicroSD Blackbox, 5V/9V BEC, easy soldering, and more. It builds upon F7 features and has a Bluetooth chip. The SpeedyBee app lets you Betaflight configure/tune wirelessly. It's DJI HD ready and supplies 9V for HD video transmitters. UART2 is for Bluetooth tel., MicroSD for Blackbox, dual 4in1 ESC ports for x8 Octocopter, and BetaFlight OSD for FPV display. LED/buzzer pad, I2C pad for external GPS/Magnetometer.
Check out our other 30x30 flight controllers and the rest of our HolyBro selection!
Features
This V1.3 now has USB-C, 9V 3A BEC for VTX, and JST-SH connector for VTX port.
Specifications
MCU - STM32H743 32-bit processor running at 480 MHz
Professional underfill epoxy for mechanical reinforcement
IMU - MPU6000
Barometer - BMP280
OSD - AT7456E
Onboard Bluetooth chip - ESP32-C3
SpeedyBee IOS & Android App Compatible
Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) and turn on automatically when the flight controller is locked (disarm) in Betaflight
6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry)
9x PWM Outputs (8 Motor Output, 1 LED)
2x JST-SH1.0 8pin ESC port (4in1 ESCs, x8/Octocopter compatible)
1x JST-SH1.0 6pin VTX port (For HD System like Caddx Vista & Air Unit)
Battery input voltage: 2S - 8S
BEC 5V 2A Cont.
BEC 9V 3A Cont
USB Type-C
Mounting - 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets
Dimension - 35x35mm
Weight - 8g
Includes
1x Holybro Kakute H7 V1.3 3-6S 30x30 Flight Controller w/ Bluetooth - MP6000
1x Wiring Kit
Wiring Diagram
A serious fixed-wing pilot can count on the Holybro Kakute H743 Wing flight controller for powerful operation and reliable performance. Equipped with the STM32 H743 Processor running at 480 MHz, CAN Bus support, dual camera support & switch, 9V/12V ON/OFF Pit Switch, and plug-and-play GPS, and I2C ports, this controller is designed for fixed-wing & VTOL applications. Featuring an intuitive layout, it works with INAV and Ardupilot systems for rapid setup and precise control.
Choose between having the pin headers solder on or loose.
Check out our other wing flight controllers and the rest of our HolyBro selection!
Features
STM32H743 MCU running at 480 MHz
High-Precision / low-noise ICM-42688-P IMU
CAN Bus Support
Dual Camera Inputs switch
3 On-board BEC output 5V, 6V/8V and 9V/12V
9V/12V ON/OFF Pit Switch
On-board voltage & current sensor
Integrated BMP280 barometer
Plug-and-play GPS, CAN, I2C ports
Small & low-profile design fits into compact frames
Supports INAV (6.1.1 & later), Ardupilot (4.4 & later)
Holybro Kakute H743-Wing Manual v1.0
Specifications
MCU: STM32H743, 480 MHz, 1MB RAM, 2MB Flash
IMU: ICM-42688P (SPI3)
Baro: BMP280 (I2C4)
OSD: AT7456E (SPI2)
Blackbox: MicroSD card slot on SDMMC2
7x Uarts (1,2,3,5,6,7,8) with built-in inversion.
14x PWM outputs, 1x CAN, 5x ADC (Bat1/Curr1, Bat2/Curr2 and RSSI)
3x I2C (I2C1 and I2C2 for external devices, I2C4 for onboard sensors)
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator (Green)
USB/DFU Key Extender with USB Type-C
Dual Camera Inputs switch
5V/9V(12V) for Camera/VTX power switch
High-precision Current Sense (90A continuous, 220A peak)
Battery Voltage Sensor: 5K:25.5K (Scale 1800 in INAV, BATT_VOLT_MULT 18.18 in ArduPilot)
Static power 160mA@5V
Firmware Support
Ardupilot Target: KAKUTEH7-Wing(Ardupilot 4.4 or newer)
INAV Target: KAKUTEH7Wing (INAV 6.1.1 or newer)
PDB
Input voltage range: 10~36V (3~8S LiPo)
1x ESC power pads
Current Sense: 90A continuous, 220A peak. (Scale 275 in INAV, 36 A/V in ArduPilot)
BEC 5V output
Designed for FC, Receiver, OSD, Camera, 2812 LED Strip, Buzzer, GPS, Air Speed Sensor, etc.
Output 5.15 +/- 0.1V DC
Continuous current 2 Amps, 3A Peak
BEC 9V /12V output
Designed for Video Transmitter, Camera, Gimbal etc.
Continuous current 2 Amps, 3A Peak
12V option with Jumper pad
BEC Vx output
Designed for Servos
Voltage adjustable, 6V Default, 8V option with Jumper pad
Continuous current 6 Amps, 8A Peak
BEC 3.3V output
Linear Regulator
Continuous current: 200mA
Mechanical
Mounting: 25 x 25mm, M2 hole
Dimensions: 45x 30 x 13.5 mm
Weight: 28g with USB extender
Includes
1x HolyBro Kakute 3-8S Fixed Wing Flight Controller
1x Power Board
1x Top Board
1x USB-EXT Board
1x GPS Module (Optional)
1x Electrolytic capacitor: 220uF 62v
2x XT60 60mm Power Cable
4x Sets 2.54 DuPont Pin
2x JST-GH 4Pin Cable
1x 15cm JST-SH 6Pin Cable (For USB-EXT Board)
Wiring Diagram
A serious fixed-wing pilot can count on the Holybro Kakute H743 Wing flight controller for powerful operation and reliable performance. Equipped with the STM32 H743 Processor running at 480 MHz, CAN Bus support, dual camera support & switch, 9V/12V ON/OFF Pit Switch, and plug-and-play GPS, and I2C ports, this controller is designed for fixed-wing & VTOL applications. Featuring an intuitive layout, it works with INAV and Ardupilot systems for rapid setup and precise control.
Choose between having the pin headers solder on or loose.
This Micro GPS uses multi-constellation GNSS powered by u-blox M10, a concurrent GNSS receiver that can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture, all four major GNSS constellations, GPS, Galileo, GLONASS, & BeiDou, can be received concurrently. It also comes with the IST8310 compass.
Firmware Support for M10 GPS: PX4 1.14, ArduPilot 4.3, INAV 5.0.0, Betaflight 4.3.0 or newer is required.
Check out our other wing flight controllers and the rest of our HolyBro selection!
Features
STM32H743 MCU running at 480 MHz
High-precision / low-noise ICM-42688-P IMU
CAN Bus Support
Dual Camera Inputs switch
3 On-board BEC output 5V, 6V/8V and 9V/12V
9V/12V ON/OFF Pit Switch
On-board voltage & current sensor
Integrated BMP280 barometer
Plug-and-play GPS, CAN, I2C ports
Small & low-profile design fits into compact frames
Supports INAV (6.1.1 & later), Ardupilot (4.4 & later)
Holybro Kakute H743-Wing Manual v1.0
Specifications
H743-WING
MCU: STM32H743, 480 MHz, 1MB RAM, 2MB Flash
IMU: ICM-42688P (SPI3)
Baro: BMP280 (I2C4)
OSD: AT7456E (SPI2)
Blackbox: MicroSD card slot on SDMMC2
7x Uarts (1,2,3,5,6,7,8) with built-in inversion.
14x PWM outputs, 1x CAN, 5x ADC (Bat1/Curr1, Bat2/Curr2 and RSSI)
3x I2C (I2C1 and I2C2 for external devices, I2C4 for onboard sensors)
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator (Green)
USB/DFU Key Extender with USB Type-C
Dual Camera Inputs switch
5V/9V(12V) for Camera/VTX power switch
High-precision Current Sense (90A continuous, 220A peak)
Battery Voltage Sensor: 5K:25.5K (Scale 1800 in INAV, BATT_VOLT_MULT 18.18 in ArduPilot)
Static power 160mA@5V
Firmware Support
Ardupilot Target: KAKUTEH7-Wing(Ardupilot 4.4 or newer)
INAV Target: KAKUTEH7Wing (INAV 6.1.1 or newer)
Micro M10 GPS
GNSS Receiver: Ublox M10 Receiver
Number of Concurrent GNSS: Up to 4 (BeiDou, Galileo, GLONASS, GPS, QZSS)
Compass: IST8310
Frequency Bands: GPS L1, Galileo E1, GLONASS L1, BeiDou B1, SBAS L1, QZSS L1
Output Protocol: UBX (U-blox), NMEA
Nav. Update Rate: Up to 25 Hz (single GNSS) and Up to 10 Hz (4 concurrent GNSS)
GNSS Augmentation System (SBAS): WAAS, EGNOS, MSAS
GNSS Augmentation System (QZSS): L1S (SLAS)
Default Baud Rate: 38400
Input Voltage: 4.7-5.2V
Accuracy: 1.5m
Speed Accuracy: 0.05 m/s
Port Type: JST-GH-6P
Antenna: 25 x 25 x 4mm ceramic patch antenna
Power consumption: Less than 200mA @ 5V
Port Type: JST-GH-6P
Operating Temperature: -40~80C
Dimension: 32 x 26 x 9mm
Weight: 14g
Other Notes: LNA MAX2659ELT+ RF Amplifier, Rechargeable Farah capacitance, Rechargeable Farah capacitance
PDB
Input voltage range: 10~36V (3~8S LiPo)
1x ESC power pads
Current Sense: 90A continuous, 220A peak. (Scale 275 in INAV, 36 A/V in ArduPilot)
BEC 5V output
Designed for FC, Receiver, OSD, Camera, 2812 LED Strip, Buzzer, GPS, Air Speed Sensor, etc.
Output 5.15 +/- 0.1V DC
Continuous current 2 Amps, 3A Peak
BEC 9V /12V output
Designed for Video Transmitter, Camera, Gimbal etc.
Continuous current 2 Amps, 3A Peak
12V option with Jumper pad
BEC Vx output
Designed for Servos
Voltage adjustable, 6V Default, 8V option with Jumper pad
Continuous current 6 Amps, 8A Peak
BEC 3.3V output
Linear Regulator
Continuous current: 200mA
Mechanical
Mounting: 25 x 25mm, M2 hole
Dimensions: 45x 30 x 13.5 mm
Weight: 28g with USB extender
Includes
1x HolyBro Kakute 3-8S Fixed Wing Flight Controller
1x Power Board
1x Top Board
1x USB-EXT Board
1x GPS Module (Optional)
1x Electrolytic capacitor: 220uF 62v
2x XT60 60mm Power Cable
4x Sets 2.54 DuPont Pin
2x JST-GH 4Pin Cable
1x 15cm JST-SH 6Pin Cable (For USB-EXT Board)
Wiring Diagram
The iFlight 5V/12V Step Down Micro BEC features high-efficiency synchronous rectification and the ability to step down from a wide input voltage range of 2-8S(5-36V) and provide a lower stable output voltage. It's an incredibly compact solution for still being able to provide 3 amps at 5 volts, and 2 amps at 12 volts.
For those looking for something even smaller and only needing 5V 2A output from 3-6S input, may we suggest the iFlight 3-6S Micro 5V 2A BEC.
Check out the Rest of our iFlight product range and PDB/BEC selection while you're at it!
Features
Step-down Switch Mode
High-efficiency Synchronous Rectification
Wide Input voltage range
Voltage output can be 5V or 12V* (default 5V)
*When the "ON-12" Jumper pads are shorted, the output voltage is 12V 2A. When open, the output voltage is 5V 3A. See enlarged image below.
Specifications
Input voltage: 2-8S(5-36V)
BEC Output: 5V/2A, 12V/3A (default 5V/2A)
Dimensions: 12x14x4.5mm
Pin Spacing: 2.55mm
Weight: 1.8g
Includes
1x iFlight Micro 2-8S BEC - 5V/12V Output
1x Connecting Cables Set
Voltage Switch Jumper:
BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster-responding speed and a smoother flying experience.
Check out all our individual ESCs and all our iFlight gear!
Features
2-8S input
80A 8 layers 4OZ copper PCB, better operating load capacity;
11 pieces TDK MLCC total 420UF Low ESR capacitors, lower ripple, and more stable.
Top grade NTMFS5C430NL MOSFET, stable and reliable;
A 3528 LED for power- on display;
Rational layout, large soldering pad, countersinks, and semicircle orifices enable each layer to be energized after power-on.
Specification
Dimension: 40x17mm
Weight: 9.5g without wire
Supports 2-8S lipo input
STM32G071 MCU, 48Mhz Runs BLHELI 32.X Firmware
Capacitance: total 240UF Low ESR
BEC: No
Supports: DShot DShot150/300/600/MultiShot/OneShot PWM Drive
Target: IFLIGHT_BLITZ_G2
Supports
Current Sensor
Telemetry output
Motor Timing
Brake on Stop
Includes
1x BLITZ E80 Single ESC
1x 50V 470uf capacitor
1x Power cables & ESC signal wire set
The ISDT Air8 DC Smart charger is the upgraded version of the popular ISDT Q8. All the features and power density that made the original Q8 so popular. This charger is a 500W 20A 1-8S DC Smart Charger with APP remote control and BattAir Support! With the ISDT app you can easily control and monitor your charge direct from your phone, and even update the charger's firmware over-the-air. Being a 4th generation smart charger, you get an innovative and intuitive interface allowing easy access to all the advanced charging features while keeping it simple straightforward process for ease of use.
Check out all our chargers & charging accessories, as well as our ISDT selection!
Features
Supports a 8S ULiHv Battery - Air8 support 1~8S Life, Lilon, Lipo, ULiHv batteries, even includes the ULiHv battery with 4.45V/cell.
Upgrade Firmware - OTA upgrade in ISDLink APP, or upgrade on PC by USB port.
Support 1~12S Pb Battery and 1~16S NiMH/Cd battery.
Supports a BattAir Smart Battery
Touch board controls
APP Remote Control
Specifications
Input Voltage: DC 10~34V
Output Voltage: DC 1~34V
Max. Input Current: DC 20A
Charging Current: 0.1~20A
Discharge current: 0.1~1.5A
Balance Current: 1.5A/Cell
Max Charging Power: 500W
Max Discharge Capacity: 15W
Supported Battery Types: LiFe, Lilon, LiPo 1-8S, LiHv 1-7S, Pb 1-12S, NiMH/Cd 1-16S
Weight: 160g
Includes
1x ISDT Q8 500W 20A Smart Charger
The ISDT BG-8S is a multipurpose battery checker. It comes lots of great features to help check your batteries, receiver signals and even has a USB output that allows you to charge your phone or other devices. The display that can easily be seen in sunlight and has an easy to use menu system to show all functions and data.
Check out our other ISDT products!
Features
Battery voltage check
Battery balancing
Power bank for mobile devices
Receiver signal test and protocol analysis
Upgrade via USB port
Multi language support
Specifications
Working voltage: 5.0V - 36V
Input voltage 1s: 0.8V - 15V
Input voltage 2-8S: 0.8V - 4.8V
Battery cells: 1-8S
Voltage measurement accuracy: ±0.005V @ 4.2V
Balancing cells accuracy: <0.005V
Support USB charging: Q2.0/C3.0, BC1.2, Maximum output 12V/2A
Support smart battery: Charging and discharging setting, read battery info and usage history
Supported Batt. Type: LiHv (1-8S) / LiPo (1-8S) / LiFe(1-8S) / Lilon (1-8S) / NiMH/Cd(1-10S)
Display: 2.4” 320×240 260,000 color IPS LCD
Dimension: 80x55x19mm
Weight: 59g
Operating Temperature: 0-40℃
Working Humidity: 10%-90%RH (noncondensing)
Storage Temperature: -20-60℃
Storage Humidity: 5%-90%RH (noncondensing)
Includes
1x ISDT BattGo BG-8S Smart Battery Checker
The ISDT P20 500Wx2 Charger is the perfect middle-ground between small and large chargers. Dual channels support up to 1000W of output, 20A per channel, or 35A synchronized charging. It's engineered to be lightweight and is cooled by an advanced air convection design, with a solid magnesium alloy shell.
Check out all our chargers & charging accessories, as well as our ISDT selection!
Features
High Power DC lipo charger: Independent dual channel, synchronous parallel charging, charging current: 20AX2, Max. charging power: 500WX2, 800W parallel charging, Input current: 35A, advanced crafty cooling air duct for high-efficiency heating dissipation.
ISDT P20 Lipo charger with Smart Display: 6S lipo charger with a full-color LCD, touch panel will indicate the whole charging process for batteries, with a large screen display can show voltage, current, charging time, mode, battery type, internal resistance, and battery capacity that charged, easy setup and manual operation modes.
ISDT Charger & Multiple Functions: The P20 lipo balance charger passed US safety certification and comes with Li-ion and Lipo balancing, fast charging, data storage, cyclic charging, and discharging function. After fully charged, it will automatically stop charging.
Various battery type compatibility: RC car battery charger, All-in-one control for LiFe, LiIon, LiPo 1-8S, LiHv 1-7S, Pb 1-12S, NiMH/Cd 1-16 RC car /vehicle/plane/drone batteries, automatic battery type identification with intelligent charge algorithm matching,rc lipo charger with balance. (No power cord!)
Multi-Application: Aluminium alloy shell with good hand feel and nice appearance, our hobby charger can be widely used in RC drone/rc plane/rc ship/RC vehicle, portable devices, remote control car etc. Auto adjustment feature on charging parameters and auto safety shut-off for best charging performance. To help extend battery life with more reasonable.
Specification
Input voltage DC 10~34V
Output voltage DC 1~34V
Max. input current 35A
Charging current 0.2~20.0A x2
Max. charging power 500W x2
Balance current 1.5A/Cell Max
Discharging current 0.2~1.5A x2
Max. discharging power 15W x2
Abnormal voltage alarm Support
Incorrect cell count setting alarm Support
Supported battery types and cell count LiFe, LiIon, LiPo 1-8S ; LiHv 1-7S ;
Pb 1-12S ; NiMH/Cd 1-16S
Parallel charging power and current 800W/35A
Parallel discharge power and current 30W/3A
Input anti-reverse function support
Output anti-reverse function support
Input anti-spark function support
Output anti-spark function support
Working temperature 0~40℃
Storage temperature -20℃~60℃
Dimension 105x105x47mm
Weight About 350g
Includes
1x ISDT P20 1000W 1-8S 40A Dual Channel DC Smart Charger - Black
The ISDT Parallel Charging Board is an extremely high quality and safe balance board, charge up to 4 XT60 lipos at once.
Check out our other Battery Chargers and Accessories!
Specifications
Max Input Current: 40A
Max Output Current: 30A/Port
Max Balance Current: 2A
Balance Cells: 1s~8s
Plug: XT60
Balance Cable: 6S
Includes
1x ISDT Parallel Charging Balance Board
Take your drone filming to the next level with the Luma 55 freestyle frame kit. Offering superior performance and durability, it allows you to push the boundaries of traditional quadcopters and capture stunning visuals like never before. 5.5" provides extra thrust and performance beyond what a standard 5" can offer, to accommodate the heavier GoPro cameras we now love and use. The Luma 55 strikes a perfect balance between the agility of a 5-inch freestyle drone and the planted feel of a 6-inch cinematic cruiser, creating a harmonious blend of speed and stability perfect for cinematic work. With the Luma 55, you can effortlessly track and follow fast-moving subjects such as drift cars, boats, and motorbikes, capturing stunning footage with precision and ease.
Be sure to check out all our 5" frames, as well as our Luma Quads Products!
Features
Support for up to 5.5" props
HD VISTA / Analog / DJI O3 Air Unit Compatible
Replaceable 6x8mm arms. (single design)
Vibration dampened main stack mounting
The mounting support for the new Air Unit 03 Camera as well as other MINI to Nano sized FPV cameras
T300 carbon frame
YFS 12.9 grade steal hardware bolts
Complete set of 3D prints for your quad
Specifications
Stack Mounting: 20x20mm
Rear Mounting: 20x20mm and 25.5x25.5mm
Motor Mount Pattern: 16x16 and 19x19mm (M3)
Mid Plate Thickness: 2mm
Top and Bottom Plate Thickness: 2.5mm
Motor to Motor: 245.7mm
Arm Thickness: 6mm
Frame Weight With TPU: 160g
Includes
1x Luma Quads Luma 55 5.5" Freestyle Frame Kit
1x Hardware set
1x 3D Print Set
2x Luma Lipo Straps
Luma 55 Official 4.4 Betaflight PID Tune
Team Luma is proud to bring all Luma 55 pilots a new Betaflight tune for 4.4!
Along with the improvements to GPS rescue and HD integration, 4.4 has had a complete overhaul of the PID controller, which means that a new tune was required to allow for optimum performance. Much like the previous tune for Betaflight 4.2, this revised tune was completed in collaboration with none other than Team Luma pilot Joseph Webb (otherwise known as JWebb FPV), and has been pushed to its absolute limits. Joseph is a true legend in the Australian drone industry. Known for his incredible freestyle piloting skills and unmatched expertise in Betaflight tune development, he is a valuable contributor to our mission of creating the most outstanding products for our entire community.Check out Joseph here: https://www.instagram.com/jwebb.fpv/ and his YT Channel here: https://www.youtube.com/@JWebbFPV and show him some love!
Notes:
- This tune was deveolped using 2306.5 Size motors.- To allow for optimum performance, we recommend installing a 1000μF 35V Low ESR capacitor, along with a TVS diode.
- Be sure to use the latest BF Configurator (we're using 10.9.0)
- Ensure that you cross-reference the values after the CLI dump with the screenshots below (better safe than sorry!)
- Filters were left untouched to ensure that the tune had proper continuity between builds. If you are looking to extract more performance, or attempting to rectify an issue, add more or less filtering via the sliders as required.
- Make sure that you test hover the Luma 55 in a safe area, and check motor temperatures after 20-30 seconds. If they are hot to the touch, then do NOT proceed - ensure the build is up to scratch, and if the issue persists, get in contact and we'll do our best to point you in the right direction
Thank you for your continued support.
DISCLAIMER: LumaQuad does not hold responsibility or liability for any mechanical damage to your personal setup - this tune has been tested and verified on multiple setups to ensure that it is safe for customers.
4.4 Tune (Official v1.0)
CLI Input.
set dterm_lpf1_dyn_min_hz = 0set dterm_lpf1_dyn_max_hz = 0set dterm_lpf1_dyn_expo = 0set dterm_lpf1_type = PT1set dterm_lpf1_static_hz = 75set dterm_lpf2_type = PT1set dterm_lpf2_static_hz = 150set dterm_notch_hz = 0set dterm_notch_cutoff = 0set vbat_sag_compensation = 0set pid_at_min_throttle = ONset anti_gravity_gain = 65set anti_gravity_cutoff_hz = 5set anti_gravity_p_gain = 100set acc_limit_yaw = 0set acc_limit = 0set crash_dthreshold = 50set crash_gthreshold = 400set crash_setpoint_threshold = 350set crash_time = 500set crash_delay = 0set crash_recovery_angle = 10set crash_recovery_rate = 100set crash_limit_yaw = 200set crash_recovery = OFFset iterm_rotation = OFFset iterm_relax = RPset iterm_relax_type = SETPOINTset iterm_relax_cutoff = 14set iterm_windup = 85set iterm_limit = 400set pidsum_limit = 500set pidsum_limit_yaw = 400set yaw_lowpass_hz = 100set throttle_boost = 5set throttle_boost_cutoff = 15set p_pitch = 50set i_pitch = 55set d_pitch = 33set f_pitch = 115set p_roll = 48set i_roll = 60set d_roll = 30set f_roll = 120set p_yaw = 47set i_yaw = 60set d_yaw = 0set f_yaw = 100set angle_level_strength = 50set horizon_level_strength = 50set horizon_transition = 75set level_limit = 55set horizon_tilt_effect = 75set horizon_tilt_expert_mode = OFFset abs_control_gain = 0set abs_control_limit = 90set abs_control_error_limit = 20set abs_control_cutoff = 11set use_integrated_yaw = OFFset integrated_yaw_relax = 200set d_min_roll = 23set d_min_pitch = 27set d_min_yaw = 0set d_max_gain = 37set d_max_advance = 20set motor_output_limit = 90set auto_profile_cell_count = 0set launch_control_mode = NORMALset launch_trigger_allow_reset = ONset launch_trigger_throttle_percent = 20set launch_angle_limit = 0set launch_control_gain = 40set thrust_linear = 0set transient_throttle_limit = 0set feedforward_transition = 0set feedforward_averaging = OFFset feedforward_smooth_factor = 25set feedforward_jitter_factor = 7set feedforward_boost = 15set feedforward_max_rate_limit = 90set dyn_idle_min_rpm = 0set dyn_idle_p_gain = 50set dyn_idle_i_gain = 50set dyn_idle_d_gain = 50set dyn_idle_max_increase = 150set level_race_mode = OFFset simplified_pids_mode = OFFset simplified_master_multiplier = 100set simplified_i_gain = 75set simplified_d_gain = 110set simplified_pi_gain = 115set simplified_dmax_gain = 0set simplified_feedforward_gain = 90set simplified_pitch_d_gain = 100set simplified_pitch_pi_gain = 110set simplified_dterm_filter = ONset simplified_dterm_filter_multiplier = 100set tpa_mode = PDset tpa_rate = 30set tpa_breakpoint = 1350
Legacy 4.29 Tune (v1.0)
CLI Input.
# profile 0set dyn_lpf_dterm_min_hz = 80set dyn_lpf_dterm_max_hz = 200set dyn_lpf_dterm_curve_expo = 8set dterm_lowpass2_hz = 250set anti_gravity_gain = 6500set feedforward_transition = 38set iterm_relax_cutoff = 13set p_pitch = 68set i_pitch = 102set f_pitch = 80set p_roll = 65set i_roll = 100set d_roll = 37set f_roll = 80set p_yaw = 50set i_yaw = 80set f_yaw = 80set d_min_roll = 0set d_min_pitch = 0
LUMA 55 FRAME ASSEMBLY GUIDE
Kit contents:
Hardware:
Carbon:
4x
28mm Aluminum standoff.
1x
2.5mm Top-plate.
2x
20mm Aluminum standoff.
1x
2mm Mid-plate.
9x
Steel M3 12mm. (12.9 grade)
1x
2.5mm Bottom-plate.
5x
Steel M3 8mm. (12.9 grade)
4x
6x8mm Arms.
9x
Steel M3 10mm. (12.9 grade)
7x
M3 Steel Washer.
9x
M3 Steel Pressnut.
Extras:
5x
M3 Silicone soft-mount gummies.
1x
3mm Foam Battery Pad
1x
M5 Steel Clinch Nut.
2x
Luma 250mm Lipo Straps.
1x
M5 20mm Flathead Bolt.
5x
M3 Steel 20mm. (12.9 grade)
5x
M2 Steel 20mm. (12.9 grade)
5x
M2 Steel Nut
TPU parts:
1x
Front bumper.
4x
Arm Bumpers.
4x
Arm Wire Protectors.
4x
Mini to Nano FPV camera mounts.
1x
Front GoPro Hard mount.
1x
Rear Vista antenna and T mount
1x
Rear SMA antenna and T mount
1x
20x20 M3 stack RX mount.
1x
20x20 M2 stack RX mount.
LUMA 55 BUILD GUIDE v1.0
This is the Mid plate.Note the notch at the top of the image, this indicates the back of the frame.
This is the Bottom plate.It has no notch and the flat end at the bottom indicates the front of the frame.
Install 8x Press nuts into the 8x holes in the Mid plate as follows.
Check out the following Video from Phaser FPV For the correct way to install Press nuts into the carbon Mid plate..
DO NOT USE A HAMMER!
Install The Main stack Gummies:
Check out the following video for the correct way to install Gummies into the carbon Mid plate using Dental floss or Fishing wire.
The video shows installation into an FC/ESC.. this technique is the same for carbon.
Insert 8x 12mm M3 Cap head bolts through the Bottom plate.
Note: A single design is used for all 4 arms.
Orientate them so the rounded corners go on the top and bottom and the sharper corners are on the sides.
Attach each arm to the Bottom plate over the 12mm bolts.
Place the Mid plate loosely on top.
Flip the frame over and pick up any bolts you dropped ;)
Screw each 12 MM bolt in a single turn at a time using Loctite Blue 242 Threadlocker.
Work your way around multiple times until the whole thing comes together evenly.
Once everything's locked in nice and square you can go around and give it a final tighten.
Take 4x 10mm Bolts 2x M3 washers and the Front Bumper print.
Install washers on the front two bolts and insert through the Bumper into the bottom of the Bottom plate.
Secure with 4x 28mm Standoffs.
Insert your FPV camera mounts over the front 2 standoffs.
Grab 2x 8mm Bolts and do the same for the rear 2 holes, using 2x 20mm standoffs to secure.
Insert the rear antenna mount over the rear standoffs.
Insert 4x 20mm M3 bolts through the main stack gummies, twist gently and slowly so you don't pop the gummies out.
Use stack spacer prints if required to add some clearance so your ESC sits clear of the press nuts and carbon.
Install the Top-plate, triangle pointing to the front.
Grab 4x 10mm M3 bolts, 4x M3 Washers and the HD Mount Print.
Insert the 4 bolts through the 4 washers into the top of the mount and secure to the 4 28mm Standoffs.
Use 2x 8mm M3 bolts for the rear two holes.
Line up the Lipo pad with the triangle and stick it to the Top plate
Insert the M5 Clinch nut into the HD mount print.
Note: The nut will seat inside the lip of the print and not fall out if you seat it properly, use a little force to get it past the lip.
Arm bumpers go on the end of the arms.
The Printed Arm wire guards go over the motor wires and are secured with electrical tape.
The latest Micro BEC from Matek. These thins are tiny! Great for adding powering your 5 or 9V accessories without adding any meaningful weight to your build.
Check out the rest of our BECs and PDBs!
Features
High Efficiency Synchronous Step-down regulator
Wide 2-8S (6-30V) Operating Input Range
Continuous load current: 1.5 Amps (Max.2.5A 5s/minute)
VOut 5V or 9V Adj. Default is 5V.
VOut Load Regulation: 2%
Standby current: <5mA
Maximum Duty Cycle: 95%
OCP Protection and Hiccup
Thermal Shutdown
Output Short-circuit tolerant (5 seconds/minute)
Pins distance: 2.54mm
Dimensions: 10x14x3mm
Weight: 1g
Includes
3x Matek 2-8S Micro 5V or 9V BEC
Another feature rich offering from Matek in the 30x30 class. Loaded with features for digital and analog builds. Matek leads the pack when it comes to quality and performance.
Check out our 30x30 Flight Controllers as well as the entire Matek selection!
Features
STM32F405 has 1MB flash which can run ArduPilot/INAV/BetaFlight
InvenSense the 3rd generation IMU ICM42688-P
9-60V(3~12S LiPo) wide input voltage and voltage sense. and a 9~16V BEC for DJI OSD or analog VTX
8motors+3servos in INAV/BF multirotor mixer.
SH1.0_8pin connector for PnP with 2x 4in1 ESC
SH1.0_6pin connector for PnP with HD System(Caddx Vista & Air Unit)
USB pin breakout for connecting to external USB adapter
Specifications
Input Voltage: 3-12S
MCU: STM32F405RGT6
IMU: ICM42688-P
OSD: AT7456E, DJI OSD
Barometer: SPL06-001 (I2C)
Blackbox: 16M-byte Flash memory
UARTs: 6 + 1x Softserial_Tx option
PWM outputs: 12 (8x Dshot)
I2C: Yes
BEC: 5V 1.5A, Vx, 9~16V/1~2A (3S IN/9V 2A, 4S IN/12V 2A, 6S IN/16V 2A, 8S IN/16V 1.5A, 12S IN/16V 1A)
ADC: 4 (VBAT, Current, RSSI, Airspeed)
PINIO: Yes
Dual Analog Camera Cignal Switchable: Yes
Mounting Pattern: 30x30mm
Dimensions 36x36x5mm
Weight: 7g
Includes
1x Matek F405-HDTE Flight Controller
6x Silicon grommets M4 to M3
1x SH1.0_8pin cable 5cm, 2x SH1.0_8pin connectors
1x SH1.0_6pin to GH1.25_8pin cable 8cm for HD System(Caddx Vista & Air Unit)
Wiring Diagram
Packed with features, the H743-Slim from Matek is ready to go. Compatible with INAV, Betaflight, and ArduPilot.
Check out our 30x30 Flight Controllers as well as the entire Matek selection!
Specifications
FC Specifications
Brand name: Matek Systems
Item name: H743-SLIM Flight Controller
MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash
IMU: ICM42688P & ICM42605
Baro: Infineon DPS310 (I2C2)
OSD: AT7456E (SPI2)
Blackbox: MicroSD card socket (SDIO)
7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
13x PWM outputs(including “LED” pad)
2x I2C
1x CAN
6x ADC (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2)
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
1x SPI3 break0ut
USB Type-C(USB2.0)
1x JST-SH1.0_8pin connector (Vbat/G/Curr/Rx8/S1/S2/S3/S4)
1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G)
Dual Camera Inputs switch
5V/Vbat filtered power ON/OFF switch
DJI FPV OSD is supported by any spare UART
Power
Vbat Input: 6~36V (2~8S LiPo)
BEC: 5V 2A cont. (Max.3A)
LDO 3.3V: Max.200mA
No Current Sensor built-in
ADC Vbat2 pad supports Max. 69V (voltage divider: 1K:20K)
Static power: 200mA@5V with Betaflight, 150mA@5V with ArduPilot
FC Firmware
ArduPilot(ChiBiOS): MATEKH743
BetaFlight: MATEKH743
INAV: MATEKH743 (To be supported soon)
Physical
Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
Dimensions: 36 x 36 x 5 mm
Weight: 7g
Includes
1x Matek H743 Slim 30x30 Flight Controller
Wiring Diagram
QA:
ArduPilot Relay(PINIO
Camera-1 and Vsw On by default
Make sure 2 cameras are set with identical video format, both PAL or both NTSC.
# GPIOs
PD10 PINIO1 OUTPUT GPIO(81) //Vsw pad power switch
PD11 PINIO2 OUTPUT GPIO(82) //Camera switch
# RCx_OPTION: RC input option
28 Relay On/Off
34 Relay2 On/Off
35 Relay3 On/Off
36 Relay4 On/Off
e.g.
RELAY_PIN 81 //Vsw GPIO
RC7_OPTION 28 //Relay On/Off, Use CH7 of Transmitter to switch Vsw
RELAY_PIN2 82 //Camera switch GPIO
RC8_OPTION 34 //Relay2 On/Off, Use CH8 of Transmitter to switch camera
or
RELAY_PIN3 81 //Vsw GPIO
RC9_OPTION 35 //Relay3 On/Off, Use CH9 of Transmitter to switch Vsw
RELAY_PIN4 82 //Camera switch GPIO
RC10_OPTION 36 //Relay4 On/Off, Use CH10 of Transmitter to switch camera
The configured feature will be triggered when the auxiliary switch’s pwm value becomes higher than 1800. It will be deactivated when the value falls below 1200.
Check the pwm value sent from the transmitter when the switch is high and low using the Mission Planner’s Initial Setup >> Mandatory Hardware >> Radio Calibration screen. If it does not climb higher than 1800 or lower than 1200, it is best to adjust the servo end points in the transmitter.
Tips
ArduPilot Firmware
https://firmware.ardupilot.org/Plane/stable/MatekH743/
https://firmware.ardupilot.org/Copter/stable/MatekH743/
INAV is expected to support H743 in 2.6.
H743-SLIM has betaflight firmware preloaded for QC
BetaFlight target is not on the Github, pls download BetaFlight firmware from our website.
If you flash ArduPilot firmware via BetaFlight configurator. there is a known issue that flash process will freeze at 50% if “full chip erase” is selected. Disable full chip erase when flashing, then reset to default in Mission Planner after flashing.
It is highly recommended to use STM32CubeProgrammer to erase MCU and upload firmware http://www.mateksys.com/?p=6905
Matek's H743-Wing V3 Flight Controller arrives with new features and improvements over the original. This FC features a STM32H743VIT6 MCU running at 480MHz, dual gyros ICM42688-P(SPI1) & ICM42605(SPI4), a DPS310 (I2C2) barometer, and much more.
This version features an updated Gyro compared to the V2.
Check out our other wing flight controllers, as well as the rest of our Matek selection!
Specifications
Input Voltage: 3-8S LiPo
MCU: STM32H743VIT6
Gyro: ICM42688-P / ICM42605
OSD: Yes
UARTs: 8 Sets
ESC Connections: Yes
Firmware: MATEKH743
BEC: 3.3V, 5V, 9V, 12V
Current Sensor: Yes
Buzzer: Yes
Barometer: Yes
Black Box: Micro SD
Stack Size: Not Stack Mounted
Dimensions: 54x36x13mm
Weight: 30g
Includes
1x Matek H743-Wing V3 Flight Controller
Wiring Diagram
The all-new Redux32 PRO F4 20x20 race ESC. Some of the fastest FPV pilots in the world fly these ESCs and incorporate their feedback to make changes. The REDUX AIR Redux32 Pro F4 128KHz 32Bit 70A 3-8S 20x20 4in1 ESC is a powerful ESC that provides up to 70A continuous current and features a 32-bit processor running at 128KHz PWM frequency. The ESC is designed to handle 3-8S LiPo inputs and uses a 20x20 mounting pattern. Its 4in1 design minimizes weight and maximizes efficiency.
Specifications
Input Voltage: 3-8S
Current: 70A
Peak: >80A 10S
Mounting: 20x20
Mounting Hole: M4 —> M3 (with grommets)
MOSFETs: 5x6 (FULL-SIZE)
PWM Frequency: up to 128KHz
Protocol: BLHeli_32
Telemetry: Yes
Current Sensor: Yes
Amp Meter Scale: 200
Includes
1x REDUX AIR Redux32 Pro F4 128KHz 32Bit 70A 3-8S 20x20 4in1 ESC
1x Hardware Kit
1x Accessory Kit (capacitor, grommets, power lead w/XT60 Pigtail, FC plugin harness)
The Rush Blade F722 is a versatile 30x30 for use in various types of builds. DJI compatibility and plugs all around make this FC an incredibly easy platform to build off of!
Make sure to check out our other 30x30 Flight Controllers and the rest of our Rush FPV products!
Specifications
MCU: 216MHz
GYRO: MPU6000
OSD: Onboard
UARTS: 5
PWM Outputs: 6
Input Voltage: 3-8S
BEC: 5V/5A 10V/3A
Mounting Pattern: 30.5mm x 30.5mm
Includes
1 x Rush FPV Rush Blade F722 30x30 Flight Controller for DJI
2 x 60MM LED/RX Cable
1 x 60MM ESC Cable
1 x 110MM NAVI Cable
1 x 110MM Air Unit Cable
5 x 8MM Grommet
5 x 5MM Grommet
Wiring Diagram
The RUSH TANK II is here, featuring higher input voltage range (up to 8S), ever better filtering, a locking mechanism on the harness plug, and pads specifically for adding an AGC Mic! The TANK is a high quality Video Transmitter featuring strong anti-interference ability, power filtering, stable transmission, and more! Full metal casing with 30x30 stack mounts make this VTX truly a TANK. Rush's LOCK-ON technology eliminates frequency drift, allowing up to 8 quads in the air at once with no interference!
Be sure to check out our other Rush FPV Products and our wide variety of video transmitters!
Features
Four adjustable levels of transmitting power. (PIT/25/200/500/800/mW) The superior performance of Tank Racing VTX allows 8 quads to race in the same band, without interference.
Side LED indicators mean more intuitive status reading.
Impregnable: The newly designed power filtering system allows TANK RACING VTX to work stably with any power system within its limits without interference from power supply.
Power LUT: Built- in high precision power lookup table which performs milliwatt power calibration for all channels. Full band has it’s ownunique power output. In multi pilot flight, all pilots will benefit from this and obtain a fair and consistent signal.
LOCK-ON: Frequency drift is completely eliminated, the full frequency band power is constant, 8 pilots compete at once easily.
Silent setting: The intelligent transmit circuit of TANK will not generate any interference signal during the switching and setting of VTX.
SmartAudio protocol authorized by TBS. This can be set with RGB LEDs by conventional double buttons, which can then access SmartAudio to set up and view the VTX information via the OSD menu.
Pit Mode: After entering the pit mode, the VTX power will be reduced to minimum. The video feed is only visible to yourself at close range, so don't worry about disturbing others.
Tank Armor: Under the fully covered metal case there are 6 layers of PCB after waterproofing work. VTX is fully protected, avoiding externalinterference and achieving ultra high heat dissipation efficiency.
Simple installation, Intuitive operation.
Specifications
Item Name: Rush Tank II
Input Voltage: 7-36V DC
Output Voltage: 5V 1A
12V Input Current: 40mA@Pitmode, 95mA@25mW, 185mA@200mW, 250mA@500mW, 380mA@800mW
Channels: 48CH RaceBand / LowRace
Power: PIT/25/200/500/800 mW
Audio: Support audio input
Dimensions: 36*36*4.5 mm
Weight: 6.8g(including cable)
Includes
1x Tank VTX
1x MMCX to SMA Cable
1x 6 Pin Harness
Manufacturer Warranty Policy: Note that RushFPV has stated to us that they will not warranty items more than 30 days after purchase. However, RDQ will still warranty items which are dead on arrival or do not last a reasonable amount of time under reasonable flight conditions
Wiring Diagram
RUSHFPV brings their signature quality and style to the 20x20 form factor. Nothing but size was reduced from the 30x30 Tank Ultimate! This little beast still cranks out 800mW of clean, stable video signal for crusing far or handling heavy obstructions.
Check out out ever expanding VTX section (or just the 20x20s) as well as our RUSHFPV gear!
Features
Compact Robust Design
Variable Output from 25 to 800mW
Pit Mode
Officially Licensed Smart Audio from TBS
Optional Protective Shield Included
Specifications
Input Voltage: 7-36V(2-8S)
Transmittion Power: PIT/25/200/500/800mW
On Board DC Output: 5V 1A Max
12V Input Current:
40mA@PITMODE 95mA@25mW,
185mA@200mW 250mA@500mW,
380mA@800mW
Channels: 48 RaceBand/LowRace
Feature: Available with External Mic
Mounting Dimensions: 20x20mm (VTX Holes M3, Shield Holes M2)
Dimension: 28x28x3.3mm
Weight: 4.46g (w/o Cover), 5.40g (w/ Cover)
Includes
1x Rush Tank Mini 25-800mW 20x20 VTX - MMCX
1x Protective Cover
1x MMCX Dipole Antenna
1x Wire Set
1x Hardware Set
Manufacturer Warranty Policy: Note that RushFPV has stated to us that they will not warranty items more than 30 days after purchase. However, RDQ will still warranty items which are dead on arrival or do not last a reasonable amount of time under reasonable flight conditions
SPMXG2PS8, Spektrum RC Smart G2 PowerStage 8S Bundle w/Two 4S Smart LiPo Batteries (5000mAh)
This is a Spektrum RC Smart G2 PowerStage 8S Bundle with two 4S Smart G2 LiPo Hard Case Batteries is a one-box solution for vehicles requiring 8S power.
Spektrum Smart G2 Battery
You'll never have to set charge preferences for a Spektrum Smart battery until you want to. When a Spektrum Smart LiPo battery is connected to a Spektrum Smart charger, unique parameters and health of that Smart LiPo battery are upload from the Smart memory microchip integrated into the battery. Through the charger, you can view and set preferences, such as charge rates, so that all you have to do to charge the pack every time is press the charger "Start" button. Smart technology takes care of the rest. The updated G2 performance batteries feature an all in one connector that eliminates the need for a balance connector, as the balance process is done through the charger and the battery connector. The smart batteries also come programmed from the factory to self discharge to a safe 3.90V per cell after 72hrs of inactivity. All of the functions and features placed in this battery are intended to supply the user with a powerful and safe lithium battery.
Spektrum Smart G2 Charger
The Spektrum S2200 Smart G2 AC Charger offers fast, easy charging, especially for modelers using Smart batteries — with Auto Charge simplicity, one-connection balancing, IC3 or IC5 output ports, and more.
Features:
Charger
Up to 200W power per channel or 380W on one channel for fast charging
Charges AND balances Smart G2 batteries with one simple IC3® or IC5® connection — no separate balance lead needed
Auto Charge recognizes Smart battery charging parameters and begins safe, accurate charging automatically when connected
Charges virtually any RC battery (use Smart batteries to benefit from all charger features)
Smart software tracks and stores numerous smart battery data
Includes IC3® and IC5® charging output ports — eliminating the need for a separate IC3® or IC5® adapter to charge Spektrum Smart batteries
Large, 2.8" display screen
An on-screen clock counts down remaining charge time until your Smart battery is fully charged and ready to use
Updated user interface features fresh, intuitive menus, icons and navigation tools, plus non-slip, easy to use buttons
USB input and output ports are included for updating firmware and charging secondary devices
ON/OFF switch eliminates the need to plug in and unplug the power cord for on/off control
Detachable power cord makes transporting more convenient
Includes an efficient, low-noise cooling fan
Sleek, sturdy case fits well on a workbench and in pit or field bags
Handy rubber grips on case make it easier to plug in and remove batteries
IC3® and IC5® connectors are backwards compatible with EC3™ and EC5™ connectors
Battery
Simpler and safer to use
Balance charge through the IC3® or IC5® connector data wire — with only one connection, no balance lead required
Faster Auto Discharge at up to 1.5A to safe storage voltage for long battery life and improved performance
Thicker internal metal side plates protect cells and improve heat dissipation
Integrated microchip stores unique parameters for each battery
IC3® and IC5® connectors are also compatible with EC3™ and EC5™ styles
Specifications:
Charger
Normal/Standard Charge Rate: 0.1 - 20.0A
Product Width: 5.67" (144 mm)
Technology: Smart
Application: RC Model Battery Charger
Reverse Polarity Protection: Yes
Selectable Charge Rate: Yes
Software Updates: Yes
Hard Case: Yes
Over Current Protection: Yes
Integrated Balancing: Yes - Internal Balancer & Internal Adapter
Charge Protection Circuitry: Yes
Input Voltage: 100 - 240V AC
Maximum Continuous Discharge Rate: 1.5A
Output: 2 x 200W, or 380W on one channel
Battery Balance Connector: JST_XH
Maximum Charge Rate: 20A
Low Input Voltage Protection: Yes
PC Connectivity: Yes
Product Weight: 37.7oz (1070g)
Discharge: 0.1 - 1.5A
Number of Cells: 1 - 6S LiPo, LiIon, LiFe, 1-16 cell NiMH, NiCd, 1-12 cell Pb
Safety Timer: Yes
Short Circuit Protection: Yes
Amp Meter: Yes
Product Height: 4.13" (105 mm)
Product Length: 5.7" (145 mm)
Voltage Meter: Yes
Display: 2.8" LCD
Output Connector: IC3 and IC5 selectable
Peak Detection: Yes
Thermal Protection: Yes
Programmable: Yes
Battery Temperature Monitoring: Yes
Cooling Method: Fan
Battery
Application: Surface
Battery Balance Connector: G2 Smart
Battery Capacity: 5000-5999mAh
Battery Type: LiPo (3.7V per cell)
Battery Voltage: 14.8V
Capacity: 5000mAh
Cell Configuration: Flat
Charge Protection Circuitry: Yes
Connector Type: IC5
Hard Case: Yes
Maximum Burst Discharge Rate: 100C
Maximum Charge Current: 5A
Maximum Charge Rate: 5C
Normal/Standard Charge Rate: 1C
Number of Cells: 3
Product Height: 1.37" (35 mm)
Product Length: 5.45" (138 mm)
Product Width: 1.8" (46 mm)
Watt Hours: 55.5
Wire Gauge: 10 AWG
Includes:
(1) S2200 G2 AC LiPo Smart Charger (SPMXC2010)
(2) 4S Smart G2 LiPo 100c Battery Pack (14.8V/5000mAh) (SPMX54S100H5)
This product was added to our catalog on November 22, 2021
SPMXPS8HC, Spektrum RC Smart PowerStage 8S Bundle w/Two 4S Smart LiPo Hard Case Batteries (5000mAh)
The Spektrum Smart PowerStage 8S Bundle is a one-box solution for large scale vehicles. Designed with the simplicity of Smart Technology, the bundle includes two 5000mAh 4S 100C Smart batteries, a S2100 Smart AC Charger and two charge adapters to make charging easy.
BATTERIES
You’ll never have to set charge preferences for a Spektrum Smart battery until you want to. When a Spektrum Smart LiPo battery is connected to a Spektrum Smart charger, unique parameters and health of that Smart LiPo battery upload from the Smart memory microchip integrated into the battery. Through the charger, you can view and set preferences, such as charge rates, so that all you have to do to charge the pack every time is press the charger "Start" button. Smart technology takes care of the rest. Our Spektrum Smart 100C LiPos are ready to drop into your RC car or boat for better performance, power, and reliability. These battery packs are a great upgrade for those looking to get more punch and off the line power on nearly any setup.
SPEKTRUM SMART CHARGER
The Spektrum™ S2100 Smart Charger is the first dual-output AC Smart Charger to feature Spektrum Smart Charging technology. Small and portable, this 200W charger features the Spektrum IC3™ connector that delivers a robust connection that also reads vital battery content that relays to a bright LCD color display to clearly show unique information and log data about your Smart Battery such as how many charge cycles the pack has, and much more.
CHARGE LEAD ADAPTERS
The Powerstage Bundle includes 2 IC3 Battery / IC5 Device charge lead adapters to make charging two batteries easier.
Features:
Charger:
High-visibility color LCD screen
Simple touch-wheel interface.
Intelligent software makes charging simple.
Compact design with impressive output capacity.
High-speed processor delivers amazing performance.
Efficient, internal cooling system.
Backward compatible with non-Smart batteries.
Battery:
Integrated microchip stores unique parameters for each battery.
Smart discharge allows batteries to automatically discharge to a safe voltage.
Save time and hassle, while improving battery life.
Powerful 100C continuous discharge rating to deliver high performance and longevity.
Impact resistant ABS plastic hardcase.
No soldering required, equipped with IC3 and IC5 Connectors that are compatible with EC3 and EC5.
Includes:
(2) 5000mAh 4S 100C Smart batteries
(1) S2100 Smart AC Charger
(2) Charge adapters
This product was added to our catalog on April 1, 2021
T-Motor F55A Pro III, with its 32Bit 55A 3-8S 30x30 4in1 ESC, has support for a broad PWM frequency range of 16 - 128K. This ESC also features a heatsink designed to distribute heat evenly. T-Motor products are designed for premium FPV flying, focusing on QC and quality components that won't fail when compared to cheaper options.
Check out all our 30x30 ESCs and all our T-Motor products!
Specifications
Voltage: 3-8S Lipo
Current: 4x55A
Peak Current: 4x65A
Firmware: Firmware: BLHELI_32
Telemetry: Support
BEC: No
Size: 44x40x7.5mm
Weight: 17.8g (Including Heatsink)Mounting Hole: 30.5x30.5mm/M3
Support Wide PWM Frequency: 16-128KHZ
Amperage Meter: 200
Includes
1x F55A Pro II 4 in 1 Brushless ESC
1x 12AWG-130MM with XT60 Soldered input wires
2x 61mm Signal wire
5x Cable Protectors
3x SH0.1mm Plugs(6/8/10)
1x Capacitor
T-Motor enters the world of ESCs yet again with another that is sure to impress! 8S capable with monster mosfets! This ESC is ready to spin props and spin them fast!!
Check out all our 20x20 FCs and all our T-Motor products!
Specifications
Input Voltage: 3-8S LiPo
Max. Continuous Current: 60A
Max Burst Current: 70A
Telemetry: Yes
Firmware: BLHeli_32
Input Signal: DShot 150/300/600/1200/MultiShot/OneShot
Mounting Pattern: 20x20mm M3
Dimensions: 36x47mm
Weight: 14g
Includes
1x T-Motor F60A Mini 4-8S 20x20 ESC
T-Motor has come out with one of the most advanced F7 flight controllers on the market. With 8 motor outputs, built-in Wi-Fi and Bluetooth, this FC is ready to take on even the most demanding of FPV tasks.
Browse our 30x30 Flight Controllers and all our T-Motor products!
Features
Wi-Fi
Bluetooth
Built-in blackbox for data logging
8 PWM outputs
DJI air unit plug
Specifications
MCU: STM32F722 RET6
IMU: BMI270
Barometer: BMP280
Input Voltage: 3-8S
BEC: 10V/2A, 5V/3A
OSD: AT7456
Blackbox: 16MB Flash
Motor Outputs: 8
UARTS: 6
Target: TMOTOR F7 V2
Dimensions: 37x37x7.5mm
Mounting Pattern: 30x30mm
Weight: 8.1g
Includes
1x T-Motor F7 Pro Full Function 30x30 Flight Controller
The ToolKitRC C4 is a compact and reliable charger with a maximum output of 50W. Its small size makes it easy to carry and use on the go, and its intuitive user interface and LED display make it easy to use.
Check out all our chargers & charging accessories, and all our ToolkitRC products!
Features
User Manual
AC input
Multi-chemistry
Visible capacity
High precision
Multiple protections
4-level adjustable current
Specifications
Input voltage: AC 100~240V @ 55Max
Output: DC17.4V @ Max 4.0A
Battery type: LiPo / LiHv /LiFe @ 2~4S NiMh 5-8S
Balance current: 200mA @ 4.20V
Charging accuracy: <0.01V @4.20V
Connector: XT60
Product Size: 106x64x35mm
Product Weight: 165g
Includes
1x ToolKitRC C4 50W 4A 2-4S Compact AC Charger - XT60
