ELCNITRIDE110, Elceram Nitride 1/10 Brushless ESC w/LCD Display Features: A color display with Thin-Film-Transistor (TFT) LCD (Liquid-Crystal Display) technology, with a resolution of 160x80 pixels. Self-diagnostic before the race: motor temperature, sensor cable, battery Post-race data evaluation Race data logging Fully programmable all through the ESC without the need for a program card or wireless module Realtime Data monitoring of the battery voltage, ESC, and motor temperatures Advanced Aluminum Nitride Ceramic Cooling Technology Extremely low internal resistance based on silver conductive layer 70% weight bias at the bottom of the esc 32-Bit MCU 13AWG Wires This product was added to our catalog on November 12, 2023

Read more less

Hobbywing Xerun XD10 Pro Drift Spec Brushless Speed Controller Features: Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages. A separate PRG/FAN port is able to power an external fan to maximize cooling performance or connect an LCD program box or WiFi module to the ESC. Variable frequency regulation of PWM & brake frequencies allows users to precisely regulate the driving & braking forces (of the motors). Multiple protections: low-voltage cutoff protection, ESC and motor thermal protection, and fail-safe (throttle signal loss protection), reverse polarity protection (the external standard cap pack will still be damaged if battery reversal occurs). Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real-time. Firmware upgrade via Hobbywing multifunction LCD program box (PC only) or OTA Programmer (item sold separately) Specifications: Application: 1/10th drift car Cont./Peak Current: 100A/800A Input Voltage: 2S LiPo/4-6S NiMH BEC Output: 5-7.4V Adjustable, Continuous Current of 5A (Switch-mode) Wires & Connectors: 13AWG 200mm Programming device: LCD program box, OTA programmer (Available through Firmware update) Firmware: LCD Program box via USB software (PC only), OTA  (iOS / Android)  Size & Weight: 40.7x35.0x32.0mm (w/Fan) Weight: 95g (w/ wires) Motor Limit: 2S LiPo/6S NiMH ?8.5T Includes: (1) XD10 PRO ESC  (2) Input wires & (3) Output wires (PRE-SOLDERED) (1) cooling fan  Decals Bonus parts: heat tubes, double tape, nylon cable zap traps This product was added to our catalog on May 3, 2023

Read more less

HWI30104002, Hobbywing EZRun Max4 HV 1/5 Scale Sensored Brushless ESC The Hobbywing EZRun Max4 HV 1/5 Scale Sensored Brushless ESC is the most advanced high voltage ESC on the market. It’s dynamic functionality and 12S specifications meet the needs of power-hungry users. The Max4 HV offers a strong 300A continuous output power with excellent linearity at low speed and offers full-sensored mode operation when combined with a Hobbywing large scale sensored motor. Features: Extremely Powerful & Low Temperatures: The internal circuit board of the ESC has been integrated to use copper thermal conduction sink. These are built into high-reliability thermal systems to ensure proper thermal condition while supplying a continuous output current of 300A. High Reliability & Durability: Max4 HV is the most durable (hardware) and advanced (software) ESC on the market. The ESC is built using the highest quality materials available, to withstand extreme weather and surface conditions. Together with the most advanced software developed by Hobbywing engineers, Hobbywing has created a variety of overload functions to protect the ESC from damage. Applicable to All Weather Track Conditions: The IP-67 waterproof system guarantees excellent waterproofing and dustproofing protection. The whole power system is able to drive on a variety of surfaces including mud, sand, ice, snow and water without damaging the power unit. Programming/Upgrading/Data Reading Wirelessly: Using Hobbywing's OTA module and smartphone (with the HOBBYWING HW Link App installed), the user can program parameters, upgrade firmware and relevant data of the ESC. Real-Time Data & Data Logging: After connecting the OTA module (optional - not included), turn on real-time data recording function to access the operating status. Capacitor Thermal Protection: Capacitor thermal protection will effectively prevent capacitors from exploding and causing irreversible damage to the ESC due to overload. Superior Built-in BEC: The built-in BEC can support up to 25A maximum output current. The output voltage is switchable between 6V, 7.4V and 8.4V. This ensures that the ESC is able to support demanding high-torque servos. Built-In Spark-Proof Design: The built-in spark-proof circuitry helps to prevent damage to the battery connectors, as well as physical injury that could be caused by strong electrical sparks when connecting a "high voltage" battery pack (6-12S). Advanced & Secured Electronic Switch: The advanced and durable electronic switch features a longer lifespan compared to a standard switch. The dust, dirt, and waterproof switch housing ensures reliability, long life and eliminates unwanted damage. Heavy impact or harsh surfaces will not affect the switch.  Sensor Cable Interface: The MAX4 HV ESC is equipped with a proprietary sensor cable interface. It is high recommended to use the motors from Hobbywing as the waterproof protection level is at the highest level (IP67). Specifications: Cont./Peak Current: 300A/2000A Input Voltage: 6-12S Lipo BEC Output: 6V / 7.4V / 8.4V adjustable, continuous current 10A (Switch-mode) Input Wires: Red-8AWG-200mm*1/Black-8AWG-200mm*1 Output Wires: Not Included Input Connectors: Not Included Output Connectors: 8.0mm Gold (female) Fan Size: 50x50x15mm Fan Voltage Range: 6-8.4V Size: 125mmx85mmx61.7mm Weight: 775.4g KV Rating/T Count: 12S LiPo: KV ? 600KV(70125 Size Motors) This product was added to our catalog on May 13, 2022

Read more less

HWA30112003, Hobbywing Xerun XR10 Justock G3 1/10 Sensored Brushless ESC The Hobbywing XERUN XR10 Justock G3 1/10 Sensored Brushless ESC is the next level in zero timing spec racing. The timing in this ESC has been fixed to a permanent 0° to comply with stock class racing. Package includes one Justock ESC. Features: Built-in polarity protection. The XR10 Justock has integrated MOSFET's that if the battery terminals are connected in reverse, the MOSFET will be reverse-biased and will not allow current to flow through the system Programmable via OTA Bluetooth module or 3in1 program box Built-in capacitor module eliminates the need for external capacitors and unwanted space RPM speed limit function supports up to 6 different speed, RPM, selections to meet the needs and demands of various competitions in the world (Set through OTA module or 3in1 box) Internal ESC timing has been set to 0 degrees and cannot be adjusted for stock racing Built-in BEC can support a maximum output current of up to 8A. Output voltage can be set between 6V or 7.4V Calibration or preforming a factory-reset can be achieved by using this SET button. Simple and easy to use Supports both CCW (counterclockwise) and CW (clockwise) motor directions Protection functions include: reverse polarity, battery voltage, ESC temperature, motor temperature, signal lost and locked rotor protection Supports ESC firmware upgrades User-friendly and convenient for set-up Specifications: Continuous Current: 60A Burst Current: 380A Battery: 2S Lipo (Only 2S) Built-in BEC: 6V/7.4V @ 4A(Switch-mode) ESC programming: Independent programming port Motor Supported: Sensor and sensorless brushless motor Motor Limit: 10.5T 3650 Motor Application: 1/10, 1/12 On-road and Off-road Cooling Fan: Powered by BEC Size: 40.9x33.9x32.1mm (LxWxH) Weight: 75.4g (Including weight of wire)  This product was added to our catalog on May 3, 2023

Read more less

HWA30401133, Hobbywing Xerun V10 G3R Competition Stock Spec Brushless Motor (25.5T) The Hobbywing XeRun V10 G3R Competition Stock Spec Brushless Motor was developed in cooperation with Hobbywing's international team of drivers and features hundred of improvements and adjustments. Developed for competition, this motor has already proven itself at races around the world and is a great weapon for spec class racing. Features: Improved Power & RPM: The optimized stator structure, combined with the super magnetic rotor improves the G3R Stock motor's torque by 13.3%, Kv by 6.5%, and maximum power output by 8.6% compared to the previous V10 G3 Stock motor.   Low Resistance - High Efficiency: Resistance is reduced by 11%, and efficiency is improved by 6% when compared to the V10 G3. This improved efficiency helps to significantly slow down the temperature increase. Super Lightweight: The G3R is 8.6% lighter than most popular stock motors. This allows drivers to easily control the balance of their chassis. Great Heat Dissipation: The unique shell design exposes the stator core (laminations) to more air, and when combined with the holes in the front and rear end plates, helps to maximize cooling for outstanding heat dissipation. Rebuildable: The detachable structure makes regular cleaning and maintenance easy, effectively prolonging the service life of the motor and retaining efficiency. Stock & Optional Rotors: The stock super magnetic rotor (HWA30820411) is used in the 13.5 - 21.5 G3R stock motors, and is optimized for Blinky class racing. The optional rotor (HWA30820416) is optimized for Super Stock class racing where boost and turbo timing can be utilized. This motor can be optimized for either class, by simply swapping the rotor. High Quality Components: The use of high performance laminations, heat resistant pure copper wire (200°C), heat resistant rotor (180°C) with strong structure, as well as world class high precision, high strength bearings, and copper solder tabs with super current endurance help to guarantee excellent performance and durability. Specifications: Scale: 1/10th Sensored: Yes Pole Count: 2 Kv Rating: 1780kv LiPo Cells: 2-3S No Load Current: 2.1A Dimensions: 35.9x50.5mm Shaft Diameter: 3.17mm Weight: 145 grams Application: 1/10 stock class racing  This product was added to our catalog on May 3, 2023

Read more less

HWA30401139, HobbyWing Xerun D10 Drift Brushless Motor (13.5T) (Purple) Features: Designed for Drift: The Xerun D10 motors provide the ideal colors to perfectly match your drift machines. Available in Black, Red, and Purple. Banana Plug Quick-Swap Design: The motor comes factory soldered with high quality 3.5mm banana plug for easy access swap to different motors. 3.5mm male head is also included in the XD10 ESC. Stator Designed for Drift: The motor stator is optimized for drift and improves motor efficiency in drift applications. Built-in with high-precision sensors board, combined with drift-specific fan rotors, providing excellent motor linearity and drivability while greatly improves motor efficiency. Lightweight: The 10.5T motor weighs approximately 158g while the 13.5T is at 165g (including 3 gold insert weights). The lightweight motor allows user to easily tweak their weight bias on their car. Fan Rotor: Providing great heat dissipation, power the special-shaped gold fan on the rotor heats the motor while making a pleasant sound, especially when Turbo is turned on. Best paired with XD10 PRO ESC  Specifications: Application: 1/10th Drift car Input Voltage: 2S Lipo KV: 2900kv Rotor: 2 POLE ?5-12.1*24.1-BES*-L3 Weight: 157 / 165 Can Size: 35.7xx52.6mm (1.41x2.07") Shaft Diameter: 3.175mm (0.125")  Shaft Length: 15.0mm (0.591") NOTE: To avoid short circuits, ensure that all wires and joints must be well insulated before connecting the motor to related devices. The M3 screws with a length (no longer than 7mm) are needed when mounting the motor onto your vehicle. Please pay attention to the relevant marks (on the ESC) when soldering/connecting those output wires to the motor and make sure that you will strictly follow the wiring order (between the ESC & themotor) of “A-A, B-B, and C-C”. Please ensure the sensor cable is clean and undamaged when you’re using a sensor ESC. You need to pay attention to the two connectors on the cable when connecting the ESC to the motor. Re-check all the connections between the ESC & the motor and ensure that they are all correct before turning on the ESC. Timing Note: The D10 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing. You can adjust the motor timing after unfastening the screw on the rear end-plate. Please adjust the timing as needed according to the mark (white lines) at the rear end of the motor and fasten the screw after the adjustment. For obtaining optimal performance, you can change the output range and characteristics of your power system by adjusting the motor timing. Increasing the timing can increase the motor speed (RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing usually requires a high(er) ratio. Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the user manual of the ESC. After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about the motor temperature via a infra-red temperature gun. If the temperature is too high, please let the motor cool down first and then test again. If the temperature is still too high, then please reduce the timing or increase the FDR (that is to replace the pinion gear with fewer teeth or spur gear with more teeth). This product was added to our catalog on April 21, 2024

Read more less

HWI30402850, Hobbywing EZRun 70125SD 1/5 Scale Sensored Brushless Motor (560kV) Hobbywing EZRun 70125SD 1/5 Scale Sensored Brushless Motor.  Features: Exquisite Appearance: The exquisite look combined with an innovative heat sink design of the can creates a unique looking motor. Full Sensored Mode - High Power: The EZRUN series of motors are known to be dynamic and dominant. They are built differently to meet the needs of various demands on the market. It offers strong output power with an excellent linearity at low speed when operating on full-sensored mode. Applicable to All Weather & Track Conditions: The IP-67 waterproof system guarantees excellent protection in muddy, sandy, icy, snowy and wet conditions without damaging the power unit. Made for EzRun MAX4 HV ESC: The motor achieves perfect compatibility when used together with the EzRun MAX4 HV ESC. It provides ultra-large torque, precise handling performance, and brings a smooth and comfortable control experience to the users. Ultra-High Efficiency Reduces Temperature: Hobbywing technology helps to solve the degradation caused by motor overheating. It ensures that the motor is always in good working conditions. Practical Design: The motor adopts a modular detachable structure design for easy disassembly and daily maintenance. This helps to prolong the lifespan of the motor and maintaining the efficiency of the motor is simple. Unique Sensor Cable Interface: The 70125SD and Max4 HV ESC are equipped with a proprietary sensor cable interface. It is high recommended to use the motors from Hobbywing as the waterproof protection level is at the highest level (IP67). High Quality Materials & Excellent Design: The materials (Motor casing, bearings, ultra-thin silicon steel sheets, high temperature-resistance copper wire, explosion-proof rotor, high-tolerance alloy shaft) are carefully selected and approved by Hobbywing engineers. Hobbywing is serious in providing users with an extraordinary performance that will last. Specifications: Scale: 1/5th Brushed/Brushless: BL Sensored/Sensorless: SD Pole Count: 4 KV Rating: 560KV LiPo Cells: 8-12S No-load Current: 3.6A O.D.: 70mm Length: 125mm Shaft Diameter: 8mm Weight: 1995g Applications: 1/5th Heavy-duty Off-road, Truck. This product was added to our catalog on May 13, 2022

Read more less

HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T) The Hobbywing Quicrun 3650 G2 Sensored Brushless Motor is a high efficiency option, creating good power, and keeping temps low. Ideal for 1/10th, 1/12th On-road (Race or drift Touring cars, F1, M vehicles and etc.) & Off-road (Buggies/2WD SCTs & Trucks) STOCK/SPORT Class Competitions (About Motors' T counts, please refer to rules regulated by race organizers), Beginners for practice, and Rock Crawlers (applicable to 21.5T,25.5T motors) applications. Features: Built-in Hall sensor brings drivers an amazing sense of control. Top-quality components: heat-resistant magnet, heat-resistant wires and name-brand bearings. Dustproof design where motor leads exit. Features a gold-plated lockable connector which can be fastened by screws, eliminating the possibility of losing connections. Detachable structure is easy to clean and maintain, greatly prolonging the service life of the motor. Specifications: Turn: 21.5T Kv: 1800Kv LiPo: 2-3S Shaft Diameter: 3.175mm Resistance: 0.0747 ohm No Load Current: 1.3A Max Output Power: 95W Max Output Current: 28A Weight: 186g This product was added to our catalog on May 3, 2023

Read more less

HWA38020336, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (21.5T) This is the Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo. Using the precise control of the XR10 Pro G2S combined with a powerful V10 G4 motor gives the user a dominant combo! XR10 Pro G2S 160A ESC: The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC offers all the tuning options needed for competitive racing while giving reliable performance on the track. Helping to keep this ESC reliable is the Frameless Fan Design (FFD) fan system. A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. At the racetrack ESC adjustments can be crucial. The XR10 Pro G2S is packed with features such as several PWM adjustments. From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition. V10 G4 Motor: The V10 G4 Competition Stock Brushless Motor has been greatly optimized to provide maximum torque and increased power. With a lower internal resistance, this motor is more efficient and runs cooler when compared to the G3R motors. To further increase performance the motor adopts a fully exposed stator core allowing more airflow over the stator. The motor also features a high-precision endbell plate to improve consistency and structural stability. Dual sensor ports can be found allowing for different wiring setups. NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended. Features: ESC: Upgraded 32-bit M4 microprocessor with more powerful processing capability guarantees stable control and rapid response. (Industry's highest 32-bit microprocessor, increased processing speed by X4) Peak current up to 1200A. (This is not a typo) Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages. Variable frequency regulation of PWM & amp; brake frequencies allows users to precisely regulate the driving; braking forces (of the motors). Expanded range of the max. brake force brings in the active brake ranges from 101% to 150%. Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency. 10 select-to-use profiles applicable to all 1/10th RC car racing. Internal electronic key switch for long service life, high reliability; and the external switch port for connecting an external switch (included in the product box) is applicable to different situations. Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or WiFi module to the ESC. With the Updated WIFI express module (purchase separately), users are able to program parameters, upgrade firmware and check relevant data during the event using either the iPhone or Android devices. Switchable motor direction (CCW/CW) for various chassis. Multiple protections comes in standard Low-voltage cutoff protection ESC and motor thermal protection Fail safe (throttle signal loss protection) Reverse polarity protection Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real time. Firmware upgrade via Hobbywing multi-function LCD program box or WiFi Express (item sold separately). Motor: Specially designed for high-level racing.  Lightweight: The G4 Modified & Stock motors only weigh 161g & 132g respectively. The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor. The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G4 Stock motors (10.5T~25.5T), the timing is adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees. The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts. The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors effectively keep sand or dirt from getting inside and damaging the motor(s). The use of high-performance stator core, heat (200°C) resistant wire, heat (200°C) resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current endurance guarantees outstanding performance and super durability. Specifications: ESC: Cont./Peak Current: 160A / Burst: 1200A  Battery: 5-6 cells NiMH/NiCd / 2S LiPo  BEC Output: 5V-7.4V Motor Supported: Sensored and sensorless brushless motors  Suitable Motor: 3650 Motors 1/10th Touring Car: 4.5T, 1/10th Buggy: 5.5T Application: Brushless motor system for 1/10th, 1/12th Touring Cars & Buggies Racing, Splash proof Wires: Standard 13AWG 200mm Size: 37.5X30.9X32.5mm  Weight: 90g (with wires) Motor:  kV Rating: 2500kV Cell Count: 2-3S No-Load Current: 3.0A Outer Diameter: 35.8mm Length: 51.4mm Shaft Diameter: 3.175 Weight: 148g Front Bearing: 9x4x4mm Rear Bearing: 8x3x4mm Adjustable Timing: 30-60° Applications: 1/10th Stock Class Racing This product was added to our catalog on May 3, 2023

Read more less

HWI30402550, Hobbywing EZRUN 5687SL 4-Pole 1/5 Scale Sensorless Brushless Motor (1100kV) Specifications: Model: 5687SL-1100KV Pole: 4 KV (No-load): 1100KV Resistance: 0.0041 Ω Current (No-load): 4.1 A Max Output Power: 5800 W Current at the point of M.O.P: 200 A Motor Diameter: 56mm  Motor Length: 87mm Shaft Diameter: 8.0mm Shaft Length: 31.0mm LiPo Cells: 3-8 Weight: 916g (32.21oz) Applicable: 1/5th RC Vehicles Truck/Dragster Suitable ESC: Ezrun MAX5 or MAX6 ESC This product was added to our catalog on April 25, 2019

Read more less