TRA3351R, Traxxas Velineon 3500 Brushless Motor (10T/3500kV) This is the Traxxas Velineon 3500 Brushless Motor. The Velineon 3500 Brushless Motor features a precision balanced rotor, high-speed ball bearings, and ultra high-temperature Neodymium magnets for a great blend of power and long-life. The Velineon 3500 delivers consistent, high-power output, run after run. Features: Ultra high-temperature sintered Neodymium magnets provide massive torque and linear power Optimized for power and efficiency in 1/10th scale vehicles Consistent, high-power output, run after run Low-maintenance, unique Traxxas design Efficient, high-speed ball bearings Low maintenance design Precision-balanced rotor Protective end cap 10-Turn, 3500Kv Rebuildable Hex hardware Brilliant blue-anodizing finish Silicon steel laminations Delivers more power than comparable brushed motors Note: The motor is not compatible with the older TRA3355X ESC. It must be used with the newer TRA3355R ESC. This product was added to our catalog on May 8, 2021

Read more less

TRA3491, Traxxas Velineon 1200XL Brushless Sensorless Motor (X-Maxx/XRT) Traxxas Velineon 1200XL 1275kV Brushless Sensorless Motor. This replacement motor is intended for the Traxxas X-Maxx and XRT 8S monster truck platforms. Package includes one Velineon 1200XL 1275kV brushless Sensorless motor. This product was added to our catalog on September 7, 2021

Read more less

TRA3352R, Traxxas VXL Velineon 3500 Brushless Motor Rebuild Kit This is a Traxxas Motor Rebuild Kit for the VXL Velineon 3500 Brushless Motor. This is the updated kit, replacing the now discontinued TRA3352 rebuild kit. This rebuild kit includes one Velineon 3500 plastic end bell, two 5x11x4mm ball bearings, four 2.5x5mm BCS screws (with threadlock) and one rear bushing. This product was added to our catalog on May 7, 2021

Read more less

TRA3370, Traxxas Velineon VXL-3M Waterproof 1/16 Scale Brushless Power System Fits: Traxxas 1/16 E-Revo Traxxas 1/16 Mustang Traxxas 1/16 Race Truck Traxxas 1/16 Rally Traxxas 1/16 Slash Traxxas 1/16 Summit This is the Traxxas Velineon® VXL-3m forward/reverse brushless electronic speed control/Velinion 380 motor combo, and is intended for use with 1/16 scale vehicles. The Velineon ESC simplifies brushless technology with easy, built-in profiles and intuitive programming. The VXL-3m™ uses advanced circuit design that allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. It sets up, operates, and programs just like the Traxxas XL-5™ family of ESCs so there's no tricky new procedures to learn. Traxxas' exclusive patent-pending Training Mode™ is also included to limit full throttle to 50% for young or inexperienced drivers. For the most advanced users, the VXL-3m is equipped with two-stage low voltage detection to allow LiPo battery use, including powerful 11.1-volt 3S packs! The Velineon® 380 Brushless Motor uses ultra high-temperature Neodymium magnets, high-speed ball bearings, and a precision balanced rotor for big power and long-life. Since there are no brushes or commutator to wear out, the need for maintenance is virtually eliminated. The Velineon 380 delivers consistent, high-power output, run after run. Velineon VXL-3m Features: Traxxas High-Current Connector maintains pure, unrestricted power flow from the battery to the brushless power system. Built-in two-stage low voltage detection for Lithium Polymer (LiPo) battery use provides a clear signal to the driver that the battery pack is nearing its minimum voltage threshold. Wide range of battery options, including 6-12 cell NiMH or NiCad packs The patent-pending Training Mode™ is an exclusive Traxxas feature that reduces the overall power output of the VXL-3m by 50%, making it easier for new or younger drivers to control their model. When they're ready, simply change profiles to unleash full-throttle action. Advanced circuit design allows sensorless brushless motors to operate with the smoothness and precision of the best brushed systems. There's no need for additional sensor wiring and hardware complexity. The EZ-Set® push-button setup operates and programs just like other Traxxas speed controls such as the XL-5. This eliminates the need to learn a new set of procedures. The VXL-3m is programmable with three drive profiles: Sport Mode – Fwd / Brake / Rev Race Mode – Fwd / Brake Training Mode™ – 50% Fwd / Brake / 50% Rev Multi-color LED provides clear feedback Two-stage thermal shutdown protection protects the VXL-3m from overheating. Locked Rotor Protection™ prevents system damage by cutting power if the vehicle is stuck or   the motor is bound. Battery Over-Voltage Protection™ causes the ESC to go into failsafe mode if the maximum input voltage is exceeded. Water resistent case design uses rubber seals and o-rings to protect against damage caused by water and moisture. Micro-fin aluminum heatsink dissipates heat. MOSFET design provides high-current output (326 amp peak) with incredibly low resistance (.0005 (Ohm)). Gold plated 3.5mm bullet connectors on 16-gauge Maxx® Cable flow full power to the motor without performance-strangling resistance. Velineon 380 Features: Ultra high-temperature sintered Neodymium magnets provide Massive torque and linear power Optimized for power and efficiency in 1/16th scale vehicles Consistent, high-power output, run after run Low-maintenance, unique Traxxas design Efficient, high-speed ball bearings Precision-balanced rotor 8-Turn, 4000KV Rebuildable Hex hardware Brilliant blue-anodized finish Silicone steel laminations Delivers more power than comparable brushed motors  VXL-3M Specifications: Input Voltage: 6 to 12 cells NiMH, 2S to 3S LiPo Case Size: 26.5mm W x 46.5mm D x 22mm H Weight: 38 grams Motors: Sensorless Brushless Motor Limit: None On Resistance: 0.0005 Ohms PWM Frequency: 12,000Hz Peak Current: 326A Continuous Current: 52A BEC Voltage: 6.0V DC Motor / Battery Wiring: 16-Gauge Maxx® Cable Transistor Type: MOSFET Low Voltage Detection: 2-Stage indicators, switchable (on or off) Thermal Protection: 2-Stage thermal shutdown Single-button setup: Yes, Traxxas EZ-Set® Battery Input Connector: Traxxas High-Current Connector Motor Connector: TRX 3.5mm Bullet Connectors Velineon 380 Specifications: Type: Sensorless Brushless kV (RPM/Volt): 4000kV (8T) Magnet Type: High Temp Sintered Neodymium Connection Type: TRX 3.5mm Bullet Wire Size: 16g Maxx Cable Continuous Current: 25A Max Current: 50A Burst Max RPM: 50,000 Weight: 140g (4.94oz) This product was added to our catalog on May 7, 2021

Read more less

TRA3461, Traxxas Velineon 540XL Brushless Motor (2400Kv) This is a replacement Traxxas Velineon 540XL 2400Kv Brushless Motor. This motor is a replacement for the Traxxas Maxx and features 12-gauge wire and gold-plated bullet connectors to make it easy to install. Fits: Traxxas Hoss Traxxas Maxx WideMaxx Traxxas Maxx This product was added to our catalog on April 28, 2021

Read more less

HWA30401133, Hobbywing Xerun V10 G3R Competition Stock Spec Brushless Motor (25.5T) The Hobbywing XeRun V10 G3R Competition Stock Spec Brushless Motor was developed in cooperation with Hobbywing's international team of drivers and features hundred of improvements and adjustments. Developed for competition, this motor has already proven itself at races around the world and is a great weapon for spec class racing. Features: Improved Power & RPM: The optimized stator structure, combined with the super magnetic rotor improves the G3R Stock motor's torque by 13.3%, Kv by 6.5%, and maximum power output by 8.6% compared to the previous V10 G3 Stock motor.   Low Resistance - High Efficiency: Resistance is reduced by 11%, and efficiency is improved by 6% when compared to the V10 G3. This improved efficiency helps to significantly slow down the temperature increase. Super Lightweight: The G3R is 8.6% lighter than most popular stock motors. This allows drivers to easily control the balance of their chassis. Great Heat Dissipation: The unique shell design exposes the stator core (laminations) to more air, and when combined with the holes in the front and rear end plates, helps to maximize cooling for outstanding heat dissipation. Rebuildable: The detachable structure makes regular cleaning and maintenance easy, effectively prolonging the service life of the motor and retaining efficiency. Stock & Optional Rotors: The stock super magnetic rotor (HWA30820411) is used in the 13.5 - 21.5 G3R stock motors, and is optimized for Blinky class racing. The optional rotor (HWA30820416) is optimized for Super Stock class racing where boost and turbo timing can be utilized. This motor can be optimized for either class, by simply swapping the rotor. High Quality Components: The use of high performance laminations, heat resistant pure copper wire (200°C), heat resistant rotor (180°C) with strong structure, as well as world class high precision, high strength bearings, and copper solder tabs with super current endurance help to guarantee excellent performance and durability. Specifications: Scale: 1/10th Sensored: Yes Pole Count: 2 Kv Rating: 1780kv LiPo Cells: 2-3S No Load Current: 2.1A Dimensions: 35.9x50.5mm Shaft Diameter: 3.17mm Weight: 145 grams Application: 1/10 stock class racing  This product was added to our catalog on May 3, 2023

Read more less

HWA38020336, Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo (21.5T) This is the Hobbywing XR10 Pro G2S Sensored Brushless ESC/V10 G4 Motor Combo. Using the precise control of the XR10 Pro G2S combined with a powerful V10 G4 motor gives the user a dominant combo! XR10 Pro G2S 160A ESC: The Hobbywing Xerun XR10 Pro G2S 160A Sensored Brushless ESC offers all the tuning options needed for competitive racing while giving reliable performance on the track. Helping to keep this ESC reliable is the Frameless Fan Design (FFD) fan system. A frameless fan is used inside the housing allowing more air to flow through the ESC. With precise maximum airflow, racers will see no additional power draw seen with other fan designs. At the racetrack ESC adjustments can be crucial. The XR10 Pro G2S is packed with features such as several PWM adjustments. From preset frequency or the custom frequency settings, tuners can now adjust from 1K - 32K PWM for Throttle and 0.5-16K for Brakes. This allows ultra fine-tuning of throttle and brakes to suit any driver or track condition. V10 G4 Motor: The V10 G4 Competition Stock Brushless Motor has been greatly optimized to provide maximum torque and increased power. With a lower internal resistance, this motor is more efficient and runs cooler when compared to the G3R motors. To further increase performance the motor adopts a fully exposed stator core allowing more airflow over the stator. The motor also features a high-precision endbell plate to improve consistency and structural stability. Dual sensor ports can be found allowing for different wiring setups. NOTE: While the XR10 Pro G2S ESC is equipped with a built-in reverse polarity protection, the external capacitor will still be damaged if a reverse polarity does occur. For full protection an optional Hobbywing Non-polarity Capacitor Module is recommended. Features: ESC: Upgraded 32-bit M4 microprocessor with more powerful processing capability guarantees stable control and rapid response. (Industry's highest 32-bit microprocessor, increased processing speed by X4) Peak current up to 1200A. (This is not a typo) Built-in switch mode BEC with a maximum output of 10A and voltage adjustable from 5V to 7.4V (step: 0.1V) for usage with servos & other devices require different voltages. Variable frequency regulation of PWM & amp; brake frequencies allows users to precisely regulate the driving; braking forces (of the motors). Expanded range of the max. brake force brings in the active brake ranges from 101% to 150%. Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency. 10 select-to-use profiles applicable to all 1/10th RC car racing. Internal electronic key switch for long service life, high reliability; and the external switch port for connecting an external switch (included in the product box) is applicable to different situations. Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or WiFi module to the ESC. With the Updated WIFI express module (purchase separately), users are able to program parameters, upgrade firmware and check relevant data during the event using either the iPhone or Android devices. Switchable motor direction (CCW/CW) for various chassis. Multiple protections comes in standard Low-voltage cutoff protection ESC and motor thermal protection Fail safe (throttle signal loss protection) Reverse polarity protection Data logging for recording the maximum ESC/motor temperature, motor speed/RPM, and others in real time. Firmware upgrade via Hobbywing multi-function LCD program box or WiFi Express (item sold separately). Motor: Specially designed for high-level racing.  Lightweight: The G4 Modified & Stock motors only weigh 161g & 132g respectively. The built-in high precision Hall sensor combined with the high precision and balanced rotor guarantee outstanding linearity of the motor. The mechanical timing can be adjusted finely and smoothly; the skid-proof lines on the rear end plate of the motor guarantee stability of the timing after adjustment. For G4 Stock motors (10.5T~25.5T), the timing is adjustable from 30 degrees to 60 degrees; for Modified motors (3.5T~8.5T), the timing is adjustable from 20 degrees to 50 degrees. The motor case is designed to be easy to dismantle for maintenance purposes and for the replacement of common wearing parts. The special shell design which makes the stator core expose to the air maximizes cooling. Big holes on the end plates of 10.5T~21.5T motors further help reduce heat; small holes on the end plates of 5.5T~8.5T motors effectively keep sand or dirt from getting inside and damaging the motor(s). The use of high-performance stator core, heat (200°C) resistant wire, heat (200°C) resistant rotor with strong structure, imported high precision and high strength bearings, and copper solder tabs with super current endurance guarantees outstanding performance and super durability. Specifications: ESC: Cont./Peak Current: 160A / Burst: 1200A  Battery: 5-6 cells NiMH/NiCd / 2S LiPo  BEC Output: 5V-7.4V Motor Supported: Sensored and sensorless brushless motors  Suitable Motor: 3650 Motors 1/10th Touring Car: 4.5T, 1/10th Buggy: 5.5T Application: Brushless motor system for 1/10th, 1/12th Touring Cars & Buggies Racing, Splash proof Wires: Standard 13AWG 200mm Size: 37.5X30.9X32.5mm  Weight: 90g (with wires) Motor:  kV Rating: 2500kV Cell Count: 2-3S No-Load Current: 3.0A Outer Diameter: 35.8mm Length: 51.4mm Shaft Diameter: 3.175 Weight: 148g Front Bearing: 9x4x4mm Rear Bearing: 8x3x4mm Adjustable Timing: 30-60° Applications: 1/10th Stock Class Racing This product was added to our catalog on May 3, 2023

Read more less

HWA30404307, Hobbywing Quicrun 3650 G2 Sensored Brushless Motor (21.5T) The Hobbywing Quicrun 3650 G2 Sensored Brushless Motor is a high efficiency option, creating good power, and keeping temps low. Ideal for 1/10th, 1/12th On-road (Race or drift Touring cars, F1, M vehicles and etc.) & Off-road (Buggies/2WD SCTs & Trucks) STOCK/SPORT Class Competitions (About Motors' T counts, please refer to rules regulated by race organizers), Beginners for practice, and Rock Crawlers (applicable to 21.5T,25.5T motors) applications. Features: Built-in Hall sensor brings drivers an amazing sense of control. Top-quality components: heat-resistant magnet, heat-resistant wires and name-brand bearings. Dustproof design where motor leads exit. Features a gold-plated lockable connector which can be fastened by screws, eliminating the possibility of losing connections. Detachable structure is easy to clean and maintain, greatly prolonging the service life of the motor. Specifications: Turn: 21.5T Kv: 1800Kv LiPo: 2-3S Shaft Diameter: 3.175mm Resistance: 0.0747 ohm No Load Current: 1.3A Max Output Power: 95W Max Output Current: 28A Weight: 186g This product was added to our catalog on May 3, 2023

Read more less

TRA3480, Velineon® VXL-6s Brushless Power System, waterproof (includes VXL-6s ESC SKU: TRA3485 and 2200Kv, 75mm motor SKU: TRA3481) Traxxas Velineon VXL-6S Brushless Power System. This replacement power system is intended for the Traxxas E-Revo VXL 2.0 or the Unlimited Desert Racer. Package includes one motor and one ESC.Specifications: ESC: Input Voltage: (2) 2s or 3s LiPos (Max 25.2 volts) Case Size: 2.23in (58mm) x 2.83in (72mm) x 1.81in (46mm) Weight: 206.5g (7.28oz) Motor Connectors: Traxxas 6.5mm Bullet Connectors BEC Voltage: 6.0 V BEC Continuous Current: 10A BEC Peak Current: 20A Power Wire: 10-Gauge Maxx® Cable Motor: kV: 2200 Can Length: 77.5mm Can Diameter: 41.8mm Total Length: 98.5mm Shaft Length: 21mm Shaft Diameter: 4.99mm Replacement part for these models: E-Revo VXL Brushless Unlimited Desert Racer This product was added to our catalog on April 12, 2021

Read more less

TRA6250, Traxxas TRX-4M Brushless Motor / ESC Combo (3350kV) The TRX-4M Brushless Power System gives you up to 50% more speed and more crawling torque and precision than brushed power systems. Rip wheelies in your monster truck or navigate a technical crawling course in your custom High Trail rig. The new TRX-4M Brushless Power System gives you the best of both worlds! Brushless Outrunner Motor 3350 Kv Field-Oriented Control (FOC) Laser-etched motor can Includes 11-tooth brass pinion gear High-torque output Brushless ECM Compatible with TQ and TQi transmitters Use with 2s TRX-4M iD LiPo batteries True plug-and-play compatibility Two servo output channels Two Pro Scale lighting ports Three drive modes: Sport (Fwd/Rev/Brake trail running) Trail (light trail braking) Crawl (hill hold) This product was added to our catalog on September 18, 2024

Read more less

PTK-2107, ProTek RC Braided Brushless Motor Sensor Cable (90mm) This is a ProTek R/C Braided Brushless Motor Sensor Cable. This sensor cable is intended for use with any sensor-based brushless system that uses a replaceable sensor wire harness. The ProTek R/C sensor cable features flexible silicone wire shielding on each of the six sensor wires, with a black braided nylon protective sheath surrounding the sensor wires. Additionally, the braided sheath is shrink wrapped at each end providing complete protection to the cable. This protection and flexibility leads to a free moving and shock absorbing sensor cable while ensuring smooth, consistent and reliable data transfer between your ESC and motor. Choose from between 90mm and 300mm lengths. This product was added to our catalog on December 16, 2021

Read more less

Optimized for No Prep RC 2S Drag Racing - High Torque Castle Technology CSE060-0089-00, Castle Creations 1412 Sensored 4-Pole Brushless No Prep Drag Motor (6400kV) The Castle Creations 1412-6400kV Sensored 4-Pole Brushless Motor is a mid RPM design developed specifically for 2S No Prep RC drag racing. 12awg wire and 6.5mm bullet connectors have been combined with an application specific design that allow this motor to create big torque and high watt output. During the design phase, Castle went with a slightly different approach than current motors on the market. Most no prep motors are standard 540 size with very high kv (low turn). These motors rely on high RPM and low torque to push the car down the track (think turbo charged 4 cylinder). The 1412 is longer than most drag motors, which provides significantly more torque, acceleration, and cooler temps (think American Muscle). This results in a high horsepower, snappy, cool running motor. Your final drive ratio will need to be decreased (larger pinion/smaller spur) to get the RPMs up for top speed; due to the size of the motor it will take just about any gearing and CHEAT timing you can throw at it. Castle beefed up the design over a standard 14xx series motor to handle the high demands of drag racing. It uses a 5mm output shaft, 12AWG battery wires and 6.5mm bullets. Due to the high power nature of this motor it is highly recommended to use a 1/8th scale size ESC or larger. The 1/8th Mamba Monster X and 1/6th scale Mamba Monster X 8s are great pairings with this motor. SmartSense SMARTSENSE uses the motors sensors to start the motor to provide smooth starts, excellent torque, and low-speed drivability. Once the motor is turning, it seamlessly transitions to Castle’s ULTRA- EFFICIENT sensorless mode. When running, a motor must transition between different load points and a different timing advance is required for optimal efficiency at all load points. Using mechanical timing adjustments alone, you can only target one driving condition, such as higher start power or higher top end speed. This sacrifices performance and efficiency during the other driving phases. Electronic timing in SMARTSENSE will advance timing automatically for peak performance during all driving conditions. This allows users to combine the best of both worlds in an unrivaled HYBRID between smooth sensored startups and high-efficiency sensorless drive.  Features: 4-POLE 12-SLOT design boasts exceptional EFFICIENCY and produces LESS HEAT Oversized gold plated solder tabs for LESS RESISTANCE and easy soldering QUIETSENSE™ Technology shields magnetic field noise generated from the motor coils and keeps motor and ESC in sync at all times HIGHER PRECISION and MORE EFFICIENT startups OPTIMIZED design eliminates the need for mechanical timing adjustments Sensor alignment method delivers uniform timing and torque in both directions, automatically REBUILDABLE design allows users to replace front end bell with bearings or rotors with shaft ROAR standard sensor port and labeled connections High strength 180°C neodymium sintered magnets High quality, temperature-stabilized sensors High-purity, high-temperature copper windings Hardened stainless steel shaft 12 AWG high strand wire with 6.5mm male Castle bullet connectors  Kevlar wrapped rotor High RPM NMB oversized bearings High quality 0.2mm steel laminations Low resistance gold plated bullet connectors Specifications: Input Voltage Range: 2S LiPo Kv: 6400 Max. RPM: 75,000 Length: 62.5mm Diameter: 36mm Weight (w/wires): 283g (9.98oz) Shaft Length: 21mm Shaft Diameter: 0.197" (5mm) Mounting Hole Specifications: M3 @ 25mm Cooling Fan: Optional - not included Connectors: 6.5mm male Castle Bullet Connectors Application Guidelines: For 2WD Street Eliminator on 2s Recommended ESC(s): Mamba Monster X, Mamba Monster X 8s This product was added to our catalog on December 31, 2021

Read more less

KYO32891, Kyosho MR-04 EVO2 Mini-Z N-MM2 Brushless Chassis Set (5600kV) Performance Mini-Z Chassis Roller & Brushless Motor The MR-04EVO2 Mini-Z N-MM2 Brushless Chassis Set (5600kV) represents a significant leap forward in the top-tier MINI-Z series, offering a full model upgrade that pushes the boundaries of performance. Retaining the excellent MR-03 layout while introducing key enhancements, the MR-04EVO2 chassis achieves unparalleled performance improvements. The lower center of gravity (CG) resulting from the lower mounting of AAA batteries enhances stability through corners and elevates both speed and control. This thoughtful chassis design, coupled with the Sensored brushless motor, provides a total balance that takes performance to a higher level, making it a formidable competitor in the high-performance competition mini R/C car category. Quality is evident in the meticulous design and engineering of the MR-04EVO2 chassis. The front suspension improvements, including an updated kingpin-integrated knuckle for enhanced camber stability, showcase a commitment to optimizing every detail. The geometric revisions of the caster and trail contribute to more linear maneuverability, allowing drivers precise control over their vehicles. The inclusion of a ball differential as standard further refines the driving experience, optimizing rotational differences between left and right rear wheels during turns and providing moderate slip action for improved traction. The silver clear anodized finish on aluminum parts not only contributes to durability but also adds a stylish touch that matches the chassis's exceptional performance. What makes the MR-04EVO2 truly special is its adaptability and customization options. The chassis supports both narrow and wide tread settings, allowing enthusiasts to tailor their setup according to body type. Adjustable wheelbase adds another layer of customization, providing flexibility in chassis settings. The included brushless motor, Kyosho Speed House XSpeed 56 (5600kV) ensures the delivery of powerful, smooth and efficient performance! Taking the MR-04EVO2 to another level of dominance in the world of high-performance mini competition R/C cars, solidifying its position as one of the best of the best! NOTE: This is an assembled chassis that still requires additional items to run. See needed to complete list below for a list of items required to complete the model. Features: Powerful Kyosho Speed House XSpeed 56 (5600kV) brushless motor Lower CG design with lower battery mounting positions Significant performance improvements Updated kingpin-integrated knuckle to further improve camber stability Adjustable wheelbase and tread settings Adjustable wheelbase Ball differential included as standard Ball bearings have been changed to 3mm internal diameter for lower rotational resistance Geometric revision of caster and trail Improved linear maneuverability Specifications: Scale: 1/27 Length: 124.5mm Width: 72-76mm Height: 31mm Wheelbase: 98.0mm (LL) Weight: 135.5g Front Tread: 58.5 / 65.0mm Rear Tread: 61.5 / 65.0mm Gear Ratio: 7.3 / 6.3 / 5.5 / 4.9 1 Motor: XSpeed 56 (5600kV) Includes: (1) MR-04EVO2 Mini-Z N-MM2 Brushless Chassis Set w/(5600kV) Motor (1) Electronic speed controller (ESC) 6T / 7T / 8T / 9T Pinion gears Pinion gear tool Wheel wrench Spare wheel nuts Needed to Complete: (1) 2-Channel Transmitter/Receiver system (4) AAA Batteries for Chassis (1) Body (4) Tires (4) Wheels This product was added to our catalog November 22, 2024

Read more less

SPMXSEMC18, Spektrum RC Firma 8A 1/24 Rock Crawler Sensored Brushless Smart ESC/Motor Combo (4500kV) Firma 8A 1/24 Rock Crawler Sensored Brushless Smart ESC/Motor Combo. This Combo is a great choice for micro crawlers and more running on 2S LiPo power. It features a high-precision magnetic encoder and rotor position sensor that provides excellent one-to-one control feel when driving at any speed and at any angle. Perfectly suited for trail driving and rock crawling competitions. This advancement in sensored motor control allows the ESC to match the throttle input to the motor's RPM with unmatched precision. This combo is specifically designed for the Axial® SCX24 and AX24 platforms to provide the ultimate performance for maximum power and realism. Preinstalled with 2mm bullet connectors for easy installation. NOTE: Axial SCX24 vehicles equipped with (HRZ00014) 2-in1 Receiver and (HRZ00015) transmitter requires an SLT3 Transmitter and receiver upgrade for functionality. Please refer to the manual for more information. (2021 Ford Bronco, Jeep GT Gladiator, and Jeep Wrangler will require this upgrade) Features: Reliable 4500Kv Sensored Brushless Motor with excellent slow speed control and smooth operation Drop-in conversion to all Axial 1/24th Scale SCX24 & AX24 RTR vehicles. Crawler mode with forward, instant reverse and drag brake Compact Size and Ready to Install ESC Specifications: Type: Brushless Sensored Input Voltage: 1-2S BEC Voltage: 5V Weight: 10g Connector Type: PH 2.0 (High-Current Ultra Micro) Maximum Burst Current: 40A Water-Resistant: No Programmable: No Motor Specifications: Type: Brushless Sensored Input Voltage: 1-2S kV Rating: 4500kV Weight: 16g Connector Type: 2mm Bullets Poles: 2 Water-Resistant: No Programmable: No Includes: (1) 4500Kv Sensored Brushless Motor (1) 8 Amp (40 Amp Burst) 1-2S Compatible ESC This product was added to our catalog on May 8, 2024

Read more less

TRA3384, Traxxas BL-2s Brushless Motor (3300kV) Traxxas BL-2s Brushless Motor. This replacement motor is intended for the Traxxas Rustler 4x4, Slash, and Slash 4x4. This motor is designed to deliver brutal 2S power and speeds. The built in cooling fan combined with low-friction bearings ensure long lasting, efficient performance. The motor connection features a quick, single connector for easy setups with the BL-2s ESC. Package includes one brushless motor. NOTE: This motor is only designed for 2S use with the BL-2s ESC. This product was added to our catalog on September 15, 2023

Read more less

CSE060-0064-00, Castle Creations 2028 Extreme 1/5 Scale Sensored Brushless Motor (800Kv) The Castle Creations "2028 Extreme" 1/5 Scale Sensored Brushless Motor is the first of its kind - a SENSORED motor, developed for large scale, high voltage applications! The Sensored 2028 features an improved 4-POLE 12-SLOT design that boasts exceptional efficiency and produces less heat than its predecessor. Designed specifically for demanding large scale applications, the Sensored 2028 delivers next level large scale power and will no doubt hold up to the heavy throttle and extended usage that 1/5th scale vehicles like the Losi 5IVE-T, 5IVE-B or DBXL-E encounter. This is the ULTIMATE upgrade for any 1:5 scale vehicle (including gas to electric conversions) weighing up to 30 lbs for 2WD and 25 lbs. for 4WD.            Without a robust and reliable design, the massive power and efficiency can only take you so far. RC enthusiasts love pushing their equipment to the edge. Castle engineers know this and spared no expense when developing a design that could hold up to the harsh conditions that the RC community will throw at it. This results in a cooler running motor, and a cooler motor has a longer lifespan. Construction of this motor required careful component selection; each verified through internal testing to ensure the highest efficiency possible. The result is a motor with unmatched quality, performance, and reliability. Features: The 2028 Extreme can easily run in the 10 horsepower range (Burst power output for duration's typical of vehicle acceleration.)   Running modes include Sensored and an ULTRA-EFFICIENT sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Proprietary winding techniques allow Castle Creations to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Dual sensor ports to ensure optimal installation in your large-scale vehicle. Updated modern and sleek design that looks as cool as it performs. NOTE:  Items Needed for Operation: Compatible Electronic Speed Control (ESC) (see Recommended ESCs below) Product Use Statements: Monitor motor temperatures closely; overheating a motor will cause permanent damage to the magnets. Never exceed 180° F on the motor or ESC. Application Guidelines: The 2028-800KV is a water resistant design. The sensor board is coated with silicone conformal coating to protect the sensors from moisture. The sensor connections are not water resistant; water can cause signal loss which could result in loss of sensored capabilities. Castle recommends applying dielectric grease to the outside of the sensor wire connections after installation of the wire. Routine maintenance is recommended after running in wet conditions. Please refer to the Running & Maintaining document in the resources tab above for info on running and maintaining motors in wet environments. Specifications: Input Voltage Range: 12S MAX Kv: 800 Max. RPM: 45,000 Minimum Input Voltage: 3S Maximum Input Voltage: 12S Sensored Capable: Yes Can Length: 4.4" (113.2mm) Can Diameter: 2.2" (57mm) Weight (w/wires): 44 oz./1.25kg Shaft Size: Length: 30mm Diameter: 8mm Mounting Hole Specifications: 4mm holes @ 30mm spacing. Cooling Fan: Available, but not included. See 011-0019-00 here. Connectors: 8.0mm male connectors Recommended ESC: Mamba XL X Running modes: Sensorless and Sensored Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs. 2WD vehicles weighing less than 30lbs. This product was added to our catalog on March 22, 2021

Read more less

TRA3484, Traxxas Sledge Velineon VXL-6s ESC Brushless Power System, waterproof (includes VXL-6s ESC and 2000Kv, 77mm motor) Replacement part for these models: Traxxas Sledge This product was added to our catalog on April 11, 2021

Read more less

ARAG1023, AR390214 BLX3660 3200kV Brshls 10th 4-Pole Mtr 4x4 The Arrma BLX 3660kV brushless motor provides lots of speed and torque, and is perfectly balanced for use with the ARRMA BLX100 ESC unit. Features: A beautifully etched black aluminum motor can provides a premium look, while a 4 pole internal configuration keeps the power supply smooth and consistent Gold bullet connectors ensure fast and easy wire removal when you need to clean your vehicle - The aluminum motor can provides increased heat dissipation via the finned body section Recommended for use with AR390069 - BLX100 BRUSHLESS 3S ESC Specifications: Motor Type: Brushless Motor kV (# of Turns for brushed): 3200V Poles: 4 Pole Motor Length: 60mm / 2.36" Diameter: 30mm / 1.18" Shaft Length: 18.5mm / 0.73" Shaft Diameter: 5mm / 0.2" Motor Mounting Hole Diameter: M3 Motor Cable Length (Including Connector): 45mm / 1.77" Motor Connector Diameter: 4mm / 0.16" Motor Weight: 289g / 9.18 oz Includes: (1) BLX 3200kV Brushless Motor This product was added to our catalog on April 15, 2021

Read more less

HWI30402550, Hobbywing EZRUN 5687SL 4-Pole 1/5 Scale Sensorless Brushless Motor (1100kV) Specifications: Model: 5687SL-1100KV Pole: 4 KV (No-load): 1100KV Resistance: 0.0041 Ω Current (No-load): 4.1 A Max Output Power: 5800 W Current at the point of M.O.P: 200 A Motor Diameter: 56mm  Motor Length: 87mm Shaft Diameter: 8.0mm Shaft Length: 31.0mm LiPo Cells: 3-8 Weight: 916g (32.21oz) Applicable: 1/5th RC Vehicles Truck/Dragster Suitable ESC: Ezrun MAX5 or MAX6 ESC This product was added to our catalog on April 25, 2019

Read more less

TRA3371, Traxxas Velineon 380 Brushless Motor This is the Traxxas Velineon 380 Brushless motor, and is intended for use with the Traxxas 1/16 E-Revo and 1/16 Slash vehicles, but is also a excellent choice for any surface application that requires a 380 size motor. The Velineon® 380 Brushless Motor uses ultra high-temperature Neodymium magnets, high-speed ball bearings, and a precision balanced rotor for power and long-life. Since there are no brushes or commutator to wear out, the need for maintenance is virtually eliminated. The Velineon 380 delivers consistent, high-power output, run after run. Velineon 380 Features Ultra high-temperature sintered Neodymium magnets provide massive torque and linear power Optimized for power and efficiency in 1/16th scale vehicles Consistent, high-power output, run after run Low-maintenance, unique Traxxas design Efficient, high-speed ball bearings Precision-balanced rotor 8-Turn, 4000KV Rebuildable Hex hardware Brilliant blue-anodized finish Silicone steel laminations Delivers more power than comparable brushed motors  This product was added to our catalog on September 7, 2021

Read more less

HWA30401139, HobbyWing Xerun D10 Drift Brushless Motor (13.5T) (Purple) Features: Designed for Drift: The Xerun D10 motors provide the ideal colors to perfectly match your drift machines. Available in Black, Red, and Purple. Banana Plug Quick-Swap Design: The motor comes factory soldered with high quality 3.5mm banana plug for easy access swap to different motors. 3.5mm male head is also included in the XD10 ESC. Stator Designed for Drift: The motor stator is optimized for drift and improves motor efficiency in drift applications. Built-in with high-precision sensors board, combined with drift-specific fan rotors, providing excellent motor linearity and drivability while greatly improves motor efficiency. Lightweight: The 10.5T motor weighs approximately 158g while the 13.5T is at 165g (including 3 gold insert weights). The lightweight motor allows user to easily tweak their weight bias on their car. Fan Rotor: Providing great heat dissipation, power the special-shaped gold fan on the rotor heats the motor while making a pleasant sound, especially when Turbo is turned on. Best paired with XD10 PRO ESC  Specifications: Application: 1/10th Drift car Input Voltage: 2S Lipo KV: 2900kv Rotor: 2 POLE ?5-12.1*24.1-BES*-L3 Weight: 157 / 165 Can Size: 35.7xx52.6mm (1.41x2.07") Shaft Diameter: 3.175mm (0.125")  Shaft Length: 15.0mm (0.591") NOTE: To avoid short circuits, ensure that all wires and joints must be well insulated before connecting the motor to related devices. The M3 screws with a length (no longer than 7mm) are needed when mounting the motor onto your vehicle. Please pay attention to the relevant marks (on the ESC) when soldering/connecting those output wires to the motor and make sure that you will strictly follow the wiring order (between the ESC & themotor) of “A-A, B-B, and C-C”. Please ensure the sensor cable is clean and undamaged when you’re using a sensor ESC. You need to pay attention to the two connectors on the cable when connecting the ESC to the motor. Re-check all the connections between the ESC & the motor and ensure that they are all correct before turning on the ESC. Timing Note: The D10 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing. You can adjust the motor timing after unfastening the screw on the rear end-plate. Please adjust the timing as needed according to the mark (white lines) at the rear end of the motor and fasten the screw after the adjustment. For obtaining optimal performance, you can change the output range and characteristics of your power system by adjusting the motor timing. Increasing the timing can increase the motor speed (RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing usually requires a high(er) ratio. Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the user manual of the ESC. After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about the motor temperature via a infra-red temperature gun. If the temperature is too high, please let the motor cool down first and then test again. If the temperature is still too high, then please reduce the timing or increase the FDR (that is to replace the pinion gear with fewer teeth or spur gear with more teeth). This product was added to our catalog on April 21, 2024

Read more less

BEL-2041-W, White Scale Outboard with Evinrude W/ Motor White Scale Outboard with Evinrude decals.Includes: 1500KV Motor Specs: 6.10 Ounces. Steel gears Prop Shaft: 1/8" (3.17mm) prop shaft Requires: (1) Prop for 1/8" shaft, this unit will fit up to a 40mm diameter propeller. (1) 3s lipo pack. (1) 90 amp ESC  (1) Steering linkage hh-817, 4-40 rod, and OSE-83106. Options: 1500kv Outrunner motor Notes: This is designed for scale boats in the 25" (650mm) to 35" (900mm) length range and 3-5 pounds total weight.  The manufacturer suggests 1500KV motor with 3s lipo.  If your boat falls within those specs, we suggest a Raider 90amp esc, You will be required to solder connectors onto the motor. This product was added to our catalog on March 31, 2023

Read more less

ASC27468, Reedy 680-SL4 Sensorless Brushless Motor (2100kV) Reedy 680-SL4 Sensorless Brushless Motor. This replacement motor is intended for the Team Associated Rival MT8. Package includes one brushless motor. Features: Powerful 4-pole sensorless design Oversized, precision ball bearings High-strength rotor Hardened steel shaft Triple-insulated windings Low-resistance 4.0mm connectors Specifications: Cells: 3-6 LiPo, 8-18 NiMH kV Rating: 2100 Suggested Applications: Monster Truck, 1:8 Buggy & Truggy Dimensions: 68 x 41.2mm Shaft Diameter: 5.0mm Weight: 338g Connectors: 4.0mm bullet This product was added to our catalog on April 29, 2022

Read more less

CSE060-0083-00, Castle Creations 2028 1/6 4-Pole Sensored Brushless Motor (800kV) This is the Castle Creations 2028 1/6 4-Pole Sensored Brushless Motor now offered in this 1/6 version. Using the same high quality, powerful 2028 design used in 1/5 vehicles this 1/6 version has been tailored to accept the Mamba Monster X 8S ESC with 6.5mm bullet connectors and 10AWG wire. Designed to take on the harsh demands of todays 1/6 vehicles this 2028 motor from Castle Creations offers extreme power and efficiency. This 800KV motor now has an improved 4-Pole 12-Slot design that boasts exceptional efficiency and produces less heat. If you need large scale power this 2028-800KV brushless sensored motor will no doubt hold up to the heavy throttle and extended usage that 1/6th scale vehicles encounter. Features: Running modes include Sensored and an ULTRA-EFFICIENT Sensorless mode. High-strength, high-temperature grade neodymium sintered magnets combined with High-strength Kevlar wrap ensures the integrity of the rotor is not compromised during harsh running conditions. Oversized NMB bearings and vibration dampening system ensure the longest bearing life possible. Our proprietary winding techniques allow us to produce a stator assembly that is the lowest possible resistance, resulting in a cooler running motor. Dual sensor ports to ensure optimal installation in your large-scale vehicle. Updated modern and sleek design; looks as cool as it performs. Specifications: Input Voltage Range: 8S LiPo Kv: 800 Max. RPM: 45,000 Sensored Capable: Yes Length: 4.4" (112.7mm) Diameter: 2.2" (56.3mm) Weight (w/wires): 44 oz. (1.25kg) Shaft Length: 30mm Shaft Diameter: 8mm Mounting Hole Specifications: 4mm holes @ 30mm spacing. Cooling Fan: Available, but not included. Recommended CSE011-0153-00 Connectors: 6.5mm male connectors Recommended ESC: Mamba Monster X 8S Running Modes: Sensorless and Sensored Max. Recommended Vehicle Weight: 4WD vehicles weighing less than 25lbs.Includes: (1) 2028 1/6 4-Pole Sensored Brushless Motor (800kV) (1) Sensor Cable (3) 6.5mm Female Bullet Connectors Mounting Hardware This product was added to our catalog on November 16, 2022

Read more less

HWI30402850, Hobbywing EZRun 70125SD 1/5 Scale Sensored Brushless Motor (560kV) Hobbywing EZRun 70125SD 1/5 Scale Sensored Brushless Motor.  Features: Exquisite Appearance: The exquisite look combined with an innovative heat sink design of the can creates a unique looking motor. Full Sensored Mode - High Power: The EZRUN series of motors are known to be dynamic and dominant. They are built differently to meet the needs of various demands on the market. It offers strong output power with an excellent linearity at low speed when operating on full-sensored mode. Applicable to All Weather & Track Conditions: The IP-67 waterproof system guarantees excellent protection in muddy, sandy, icy, snowy and wet conditions without damaging the power unit. Made for EzRun MAX4 HV ESC: The motor achieves perfect compatibility when used together with the EzRun MAX4 HV ESC. It provides ultra-large torque, precise handling performance, and brings a smooth and comfortable control experience to the users. Ultra-High Efficiency Reduces Temperature: Hobbywing technology helps to solve the degradation caused by motor overheating. It ensures that the motor is always in good working conditions. Practical Design: The motor adopts a modular detachable structure design for easy disassembly and daily maintenance. This helps to prolong the lifespan of the motor and maintaining the efficiency of the motor is simple. Unique Sensor Cable Interface: The 70125SD and Max4 HV ESC are equipped with a proprietary sensor cable interface. It is high recommended to use the motors from Hobbywing as the waterproof protection level is at the highest level (IP67). High Quality Materials & Excellent Design: The materials (Motor casing, bearings, ultra-thin silicon steel sheets, high temperature-resistance copper wire, explosion-proof rotor, high-tolerance alloy shaft) are carefully selected and approved by Hobbywing engineers. Hobbywing is serious in providing users with an extraordinary performance that will last. Specifications: Scale: 1/5th Brushed/Brushless: BL Sensored/Sensorless: SD Pole Count: 4 KV Rating: 560KV LiPo Cells: 8-12S No-load Current: 3.6A O.D.: 70mm Length: 125mm Shaft Diameter: 8mm Weight: 1995g Applications: 1/5th Heavy-duty Off-road, Truck. This product was added to our catalog on May 13, 2022

Read more less