M03 VTX, an ultralight and high output power 5.8GHz analog VTX, is designed for 65-85mm whoop drone for longer-range flying. Check out all our Micro/Nano VTXs and all our BetaFPV gear! Features With the 25-350mW output power, the M03 VTX provides a stable image and strong transmission. Only 1.1g and a tiny size for drones like 65-85mm whoop drones. The screw mounting holes pattern is suitable with BETAFPV micro canopy. The camera connector JST-0.8 is suitable for the BETAFPV C02 camera. Comes with IPX type of antenna, just plug and play, no extra solder work needed.  M03 VTX is perfectly suitable for the 65-85mm whoop drone. We highly recommend using it with ELRS 2.4G FC board, like F4 1S 5A FC (ELRS 2.4G) or F4 1S 12A FC (ELRS 2.4G). Diagram Below is the diagram of the M03 VTX. The camera connector is JST-0.8 and it is compatible with cameras like BETAFPV C01, BETAFPV C02, and NewBeeDrone BeeEye. How to connect with the Flight Controller Here is the diagram about how to connect the M03 VTX with F4 1S 5A FC (ELRS 2.4G) board. Here is the diagram about how to connect the M03 VTX with F4 1S 12A FC (ELRS 2.4G) board. Change Band & Band & Chnanel & Power M03 VTX could only use the Smart Audio port to change the band and channel.  Enter the OSD menu by radio transmitter sticks ( Pitch Stick UP and Yaw Stick Left). Then FEATURES -> VTX SA to change the frequency point and power. Switchable power includes 25mW, 100mW, 200mW and 350mW. Except for the method via OSD menu as show above, the output power could be changed via the power button. Specifications Item: M03 5.8G VTX Output power: 25/100/200/350mW (adjustable) Supply voltage range: 4.5-5.5V Weight: 1.1g (antenna not included) VTX internal size: 18X14mm Frequency: 5.8GHz 48 channels, with Raceband: 5658~5917MHz Channel SEL: SmartAudio Modulation type: FM Frequency control: PLL All harmonic: Max -50dBm Frequency stability: ±100KHz (Typ.) Frequency precision: ±200KHz (Typ.) Channel carrier error: ±1.5dB Antenna port: 50 Ω Operating temperature: -10℃~+80℃ Camera connector: JST-0.8, compatible with cameras like BETAFPV C01, BETAFPV C02 and NewBeeDrone BeeEye. Includes 1x BetaFPV M03 25-350mW 5.8G Micro VTX - U.FL 5x 30AWG silicone wire (30mm)

Read more less

This camera was designed to fit into the NewBeeDrone BeeBrain V2 mount although the lens does protrude slightly out from the mount bumpers. All in all, this camera inside the NewBeeDrone BeeBrain V2 mount is the best combination of image quality per gram and mounting durability we could find for small, light platforms. Check out all our nano cameras, and the rest of our ever-growing selection of Caddx cameras! Features Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC and PAL(switchable) MENU: Support IMAGE: 4:3 or 16:9 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm/F2.5 Minimum illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14x14mm Wide Power Input: DC 3.7-18V Work Temperature: -20°C~+60C Work Humidity: 20%~80% Weight: 1.7g Includes 1x Caddx Ant Lite Nano 1200TVL CMOS PAL/NTSC FPV Camera

Read more less

The NewBeeDrone & Joshua Bardwell Smart Power Goggle Cable is a collaboration product between NewBeeDrone and Joshua Bardwell. Back in Mid 2021, Joshua Bardwell contacted us and brought up the idea of a smart goggle power cable adaptor. We realized that we could make a device to power a goggle through leftover 4S/6S batteries from quads since even if the battery level is at 30%, it still has enough power to supply the goggle.  At first, we thought of just making a very simple power module board that takes 2S-6S batteries and connect it with a 5.5x2.1 DC male plug and use a heat shrink to cover it. However, that method seems too unreliable so we decided to put a power indicator LED light and a buzzer to indicate the number of battery cells when you plug in a battery. The aluminum case acts like a shield to protect the hardware while providing heat dissipation for the power module. Why do we call it the Smart Power Module? Because it can automatically detect input voltage to indicate battery cell and will output voltage based on the battery voltage. If the battery voltage is too low, it will give a low voltage to trigger the "goggle low voltage" warning.  -Kelvin Check out all our NewBeeDrone products! Specifications Power input port: XT60 Power input support: 3S/4S/6S battery Calbe Length: 1.5 meters/4.92ft LED power indicator light Buzzer indicator: Beep per cell when the battery plugs in. The module will beep 6 times when a 6S battery is plugged in. Voltage Output: 6.2V - 8.7V (Based on the battery average cell voltage) Maximum Current: 2A Includes 1x NewBeeDrone & Joshua Bardwell Smart Power Goggle Cable

Read more less

Frustrated with constantly fixing struts and breaking frames, we set out to find something better. We worked with a number of manufacturers and after numerous prototypes and revisions, we are proud to introduce the Cockroach Super-Durable Brushless Frame for Tiny Whoop-style quads. Traditional Looks and Geometry maintain those flight characteristics you are used to and ensure easy compatibility with the Beebrain as well as most other popular flight controllers. Lightweight and Durable. We found a more forgiving and resilient material that doesn't sacrifice in weight or stiffness. Struts and other key support components have been redesigned to distribute and dissipate stress from crashes and falls. Total weight 3.71g Easy and Inexpensive. None of this is any good if it's super difficult to use and super expensive. So we made sure we set out to make something affordable. Key tolerances have also been fine-tuned to make installation and removal much easier. Check out the rest of our micro frames and the rest of our NewBeeDrone products! Specifications Motor Mount Pattern: Tri 6mm Weight: 3.71g Includes 1x NewBeeDrone 65mm Cockroach Brushless Super Durable Whoop Frame

Read more less

NewBeeDrone Cockroach Brushless Extreme-Durable Frame 75mm Design Intent: For this frame, we worked to develop a platform that would neither fall below expectations nor limit the creativity of the FPV community. The Cockroach 75mm is lightweight and versatile. We improved durability and worked to deliver a vibrational signature that made tuning easier so you can get the most performance out of NewBeeDrone flight controllers and motors. Every gram of frame material was either added or taken away to ensure that what was left was there for a reason. Lightweight and Durable: We found a more forgiving and resilient material that doesn't sacrifice in weight or stiffness. Struts and other key support components have been redesigned to distribute and dissipate stress from crashes and falls with a total weight of 6.98g. Traditional Looks and Geometry: This 75mm Cockroach frame has adaptable FC locations and a multitude of additional mounting points across the frame. We delivered a frame that has 2 board locations with 1x1inch or 25.4x25.4mm hole spacing. One mounting location on the top and another below to mount an additional board like a DVR or a 4K HD recording board. The 2-board mounting adaptability allows for the possibility for a pusher-style flying configuration to be used as well. 1mm Carbon Fiber Plate A 1mm carbon plate is included for increased durability insurance. Though the frame can be flown without it, the carbon allows for additional adaptability and opens the frame's use for exciting opportunities in a pusher-style configuration. Flip the frame over and install it. Please be aware, the motor screws that come with the 75mm frame are expected to be used with carbon fiber. If you choose to use them without the carbon fiber plate – the screws may contact the motor PCB. This 75mm frame does not come with just one limiting battery mounting solution. We understand that depending on the utility and flying style, many people want to run one or two 300mah Nitro Nector Golds in the traditional battery position or in a ‘toilet-tank’ position. We have developed several printable, TPU battery mount solutions to use with the frame and are always open to your suggestions. Included are 4 3D printed mounting tabs. Use 2 to mount one Nitro Nectar Gold 1s Battery and all 4 to mount 2x Nitro Nectar Gold 1s Batteries. When using 2 batteries, you can choose to run them in either series (2s) to increase voltage or parallel (1s) to increase capacity. Easy and Inexpensive.  None of this is any good if it's super difficult to use and/or super expensive. So we made sure we set out to make something affordable. Key tolerances have also been fine-tuned to make installation and removal much easier. Any of our other whoop BNFs can be directly dropped in into the 75mm frame. Check out the rest of our micro frames and the rest of our NewBeeDrone products! Specifications Motor Mount Pattern: Tri 6mm Weight: 3.71g Includes 1x NewBeeDrone 75mm Cockroach Brushless Extreme Durable Whoop Frame

Read more less

Introducing 40mm AZI props! NewBeeDrone is dedicated to providing the best FPV drone products in the industry. The Azi Props come from a 9-month project with NewBeeLabs to create micro props for flight time, speed, & control. After many iterations and tests, their team has developed light, well-rounded props for freestyle and racing. They boast linear throttle control, quicker spool-up times, cornering grip, higher top-end speed, bottom-end grunt, and efficient performance.  Check out the rest of our Micro Props, and the rest of our NewBeeDrone products. Specifications  Material: Polycarbonate Diameter: 40mm Pitch: 37.9mm Shaft Hole: 1mm 0.3g ea. Hub Thickness: 5mm Includes  1x NewBeeDrone Azi Tri-Blade 40mm Micro/Whoop Prop 4 Pack (1mm Shaft) - Choose Your Color

Read more less

Spare replacement canopy for AcroBee, BLV3. Check out all our whoop frames and all our NewBeeDrone gear!  Includes 1x NewBeeDrone BeeBrain Goober Canopy

Read more less

Check out this replacement antenna for BeeBrainBLV4 ELRS receivers, coming with a 3D printed mount and a MHF3 connector.  Check out our  ELRS accessories, and all our NewBeeDrone products! Specifications Frequency or Freq. Bandwidth: 2.4GHz Polarization: Linear Cable Length: 40mm Connector: MHF3 Includes 1x NewBeeDrone BeeT-Antenna 2.4GHz RC Antenna For ELRS - MHF3

Read more less

NewBeeDrone's latest whoop, the AcroBee BLV4 is perfect for flying indoors and outdoors. The technology and level of detail built into this whoop are astounding! With new "Smart Max" technology, uses the MCU to read the board temperature on the back of the VTX chips and uses PID control to control the output power for the VTX amplifier. If the temperature is low enough, the PID will adjust the output power higher, a maximum of 400Mw, and if the temperature rises, the output power of the VTX is lowered to avoid overheating.  With the VTX power, combined with ELRS, this whoop will fly far. Check out our other pre-built quads, as well as the rest of our NewBeeDrone selection. Features Classic Design with a newly refreshed appearance New Flow 0802 19000Kv Motors On-board temperature regulation prevents damage to boards. Built-in ELRS receiver Specifications Flight Controller: BeeBrain BLv4 ELRS MCU: STM32F411 VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX (SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna ESC: 12A BLHeliS Pre-Flash with Bluejay 0.16 target: S-H-40 48kHz ESC Connector: JST-1.0 3Pin OSD: NBD7456 Graphical OSD compatible with Betaflight OSD Receiver: ELRS2.4 Diversity receiver (ESP32 compatible with wifi&bluetooth firmware update) 2.4G T-Antenna (Top) & normal 2.4G antenna (bottom) Flight Controller Weight: 6.5g (Include antennas and battery connector) Flight Controller Size: Outer dimensions: 29x29x7.6mm Flight Controller Holes: 25.5x25.5mm Battery input: 1-2S Uart2: Tx & Rx for ExpressLRS2.4G Receiver Uart1: Tx & Rx free Power Connector: NBD-PH2.0 connector Motors: Flow 0802 19000kv Frame: Cockroach65 Brushless Frame Clear Purple Camera Mount: Goober Canopy Clear Purple Propeller: Azi Tri-blade 31mm 1.0 Clear Purple Firmware: 1. BeeBrain blv4 ELRS3.0 receiver firmware 2. BeeBrain blv4 ELRS2.0 receiver firmware All firmware can be found on their Github Page Includes 1x NewBeeDrone BNF AcroBee65 BLV4 Brushless Whoop - ELRS 2.4GHz  

Read more less

Experience top-tier flight performance with the NewBeeDrone Cricket200 V2 F722 3-6S 20x20 Dual BMI270 Flight Controller. This controller features a 3-6S power range, 20x20 mounting, and dual BMI270 processing power for a stable, reliable flight experience. Get ready for smooth, long-distance flight with this advanced drone controller. Check out our 20x20 FCs, and all our NewBeeDrone products! Features  Built-in 4 IN 1 ESC socket (including ESC telemetry, External current sensor) JST1.0 8Pin Plug and plug with NBD Cricket200 ESC/Infinity200 ESC. Also compatible with most of the ESC on the market. Built-in solder pads for ESC signal output and power Printed layout instructions ON the board - no need for instructions! DJI FPV Air Unit socket (use UART1 and UART6) 6 UARTS on board. Specifications  MCU：STM32F722 - 216MHz Gyro: 2 BMI270 BEC: 5V/3A Interface：6 Mounting Size: 20x20mm Size: 31.5x27mm Input Power:  3-6S Additional Infomation  3V3 100mA 9V 2A 18W Design for DJI FPV Air Unit 5V Camera Power BetaFlight OSD UART1 (Only RX, Air Unit connector) UART2 (Free) UART3 (Free) UART4 (TX and RX connected together for F.Port) UART5 (Only RX, ESC Telemetry) UART6 (MSP/Configuration Port for Air Unit) Firmware can be downloaded HERE. Includes  1x NewBeeDrone Cricket200 V2 F722 3-6S 20x20 Dual BMI270 Flight Controller 4x Grommets short 4x Grommets Long 1x Cricket200 FC to DJI Air module cable 70mm Wiring Diagram  

Read more less

NewBeeDrone's DJI O3 AirUnit adapter mount is made of CNC Aluminum, and it can dissipate heat from the O3 Air Unit at the same time provide a strong mounting solution for the Air Unit.  Come see our other adapters and connectors as well as all of our NewBeeDrone Products that we sell at RaceDayQuads! Specifications Material: 6061 Aluminum Alloy  Mount to air unit: 25.5x25.5 O3 AirUnit mount screw M1.6 X8mm Mount to Drone frame: 20x20 M2  Thickness: 3mm Includes 2x CNC Aluminum Parts 5x M1.6 x 8mm Stainless steel screw Philips head

Read more less

NewBeeDrone smallest OpenLager F411 gives the capability of black box recording to any drone that doesn't have it. This is fantastic for tuning and finding issues in your system ! Check out our other flight controller accessories, and NewBeeDrone Selection.  Specifications Dimensions: 15x15mm Weight: 1.3g without cable Includes 1x NewBeeDrone F411 OpenLager Mini External Blackbox Module 1x Wiring cables Wiring Diagram  

Read more less

Introducing the NewBeeDrone Flow 0702 motor, designed for whoop racing. It weighs only 1.58g (1.38g without cables) and is equipped with double ball bearings for a smooth, durable performance. Crafted with 7075 aluminum, it stands strong against the toughest racing conditions. Experience peak performance and thrill with this ultimate motor choice. Get yours today and experience the thrill of racing like never before! Check out our other micro motors and all our NewBeeDrone products!  Specifications  Motor KV: 27000 (Designed for 1S) Internal Resistance (mΩ): 285 Stator Resistance (mΩ): 7 Stator Height (mm): 2 No.of Stator Slots: 9 No.of Rotor Poles: 12 Dynamic balance (mg): ≤10mg NO-Load Current(A):P 0.80A Maximum Power (W) 15.2 Maximum Current (A): 3.8 Overall Dimension(mm): Ø1xL12.2 Shaft Diameter(mm): 30AWGxL40 ESC(A):5 Rated Voltage(V): 4.2(1S) Includes 1x NewBeeDrone Flow 0702 27000Kv Dual Ball Bearing Micro Motor 4 Pack 4x JST1.25 Whoop Motor Plug Replacement 16x M1.4x3 Screws

Read more less

Introducing the NewBeeDrone Flow 0702 motor, designed for Whoop racing. It weighs only 1.58g (1.38g without cables) and is equipped with double ball bearings for a smooth, durable performance. Crafted with 7075 aluminum, it stands strong against the toughest racing conditions. Experience peak performance and thrill with this ultimate motor choice. Get yours today and experience the thrill of racing like never before! Check out our other micro motors and all our NewBeeDrone products!  Specifications  Motor KV: 29000 (Designed for 1S) Internal Resistance (mΩ): 275 Stator Resistance (mΩ): 7 Stator Height (mm): 2 No.of Stator Slots: 9 No.of Rotor Poles: 12 Dynamic balance (mg): ≤10mg NO-Load Current(A):P 0.90A Maximum Power (W) 15.2 Maximum Current (A): 3.8 Overall Dimension(mm): Ø1xL12.2 Shaft Diameter(mm):30AWGxL40 ESC(A): 5 Rated Voltage(V): 4.2(1S) Includes 1x NewBeeDrone Flow 0702 29000Kv Dual Ball Bearing Micro Motor 4 Pack 4x JST1.25 Whoop Motor Plug Replacement 16x M1.4x3 Screws

Read more less

Check out NewBeeDrone's Flow 0802 dual ball bearing whoop motor 27000kv (Set of 4) NewBeeDrone's FLOW series now gets a 0802 motor. These 0802 27,000kv motors were selected to give an option to those who want that "FULL SEND" raw power on their 1S whoops. These brushless motors bring everything to the next level.  Check out our other 0802 motors, and all our NewBeeDrone selection! Specifications Motor KV: 27400 Maximum Current: 6.2Amp Internal Resistance: 142mΩ Maximum Power: 24.8W Stator Diameter: 8.4mm Overall Dimension:Φ11.6 x 12.2mm Stator Height: 2mm Shaft Diameter: Φ1 x 4.2mm No.of Stator Slots: 9 Lead Wire Size: 30AWG x 50mm ESC(A): 10Amp Dynamic Balance: ≤10mg Rated Voltage: 4.2V(1s) NO-Load Current: 1.60Amp Includes 4x NewBeeDrone Flow 0802 27000Kv Dual Ball Bearing Micro Motor 4 pack 4x JST1.25 Whoop Motor Plug Replacement 16x M1.4x3 Screws

Read more less

Check out the NewBeeDrone Flow 2207 2050Kv Brushless Race Motor. This motor has been through the works by professional drone pilots. Racers, especially the good racers knows what's up with having next-level parts. NewBeeDrone's fastest team has designed and tested the hell out of these motors to give us hence you, the next potential king of racing motors out there. Classic 2207 stator size, rated with 2050Kv for BEAST power for your 6S builds. Best of all, is the clean metal polish aesthetic on the motors, allowing guys to look perfect on any build. Check out our vast brushless motors selection, and all our NewBeeDrone products! Specifications Input Voltage: 6S Shaft Size: 5mm Weight: 33.3g Mounting Pattern: 16x16mm M3 Includes 1x NewBeeDrone Flow 2207 2050Kv Brushless Race Motor 1x Hardware Set

Read more less

A spare set of hardware for your BeeBrain or regular Inductrix flight control board. Check out our AIO flight controllers, as well as the rest of our NewBeeDrone selection! Includes 5x Grommets 5x Screws

Read more less

Premium Controller with Quality Parts and FeaturesFeaturing F4 Processor and 45Amp BLheli32 with NewBeeDrone Smoov-certified hardware design that supports up to 3-6S batteries to provide the best and most reliable quality and performance for either freestyle or racing. Designed to support the DJI Air Unit.Though DJI Air Unit can only support up to 4S, the Infinity300 Stack can make the DJI Air Unite compatible with 6S batteries by providing a 9V 16W clean power for the DJI Air Unit. Plug-and-Play. No need to solder tiny wires.The Infinity300 Stack includes a bundle of wires to connect the Flight Controller and ESC and a bundle of wires to connect the Flight Controller to the DJI Air Unit. No need to solder any tiny wires, making it simple and clean to build. Check out our other flight Controllers and all our NewBeeDrone products! Specifications MCU: STM32F405 CPUE @ 168mhz, can be overclocked IMU: MPU6000 OSD: Betaflight OSD w/ AT7456Ev UART Ports: 6 UARTS USB: Micro USB Input: 3-6S Installing Hole: 30x30mm M3 Weight: 14g Includes 1x NewBeeDrone Infinity305 F4 3-6S Flight Controller 4x Grommets short 4x Grommets Long 1x Infinity305 FC to DJI Air module cable 40mm 1x Infinity305 FC to DJI Air module cable 100mm 1x Infinity305 FC to DJI Air module cable 150mm Wiring Diagram

Read more less

A set of whoop motor plugs to solder onto motors and plug into whoop flight controllers.  JST 1.0 fits NewBeeDrone flight controllers while JST 1.25 fits all other flight controllers. Included are 2x red plugs and 2x black plugs. 50 mm length Check out all our pigtails and connectors as well as the rest of our NewBeeDrone selection! Includes 1x NewBeeDrone JST 1.0 Motor Plug Conversion Kit

Read more less

Are you tired of the stock DJI goggle foam that leaks light or is just plain uncomfortable? Have you tried other aftermarket DJI goggle foams that don't fit right or make it difficult to breathe from your nose? We've tried them all too and none of them come close to the quality and comfort of the NewBeeDrone Max Comfort Goggle Foam for DJI Goggles.  Created from Soft Touch NewBeeDrone Comfort Foam, our goggle foam is perfectly sculpted to fit all face shapes.  Some foams are too thin and make goggles uncomfortable.  Others are too thick and make goggles stick out too far, throwing off the balance and making them feel heavy. The NewBeeDrone Max Comfort Goggles Foam is the perfect compromise at 23mm at its thickest and 14mm at its thinnest. We named them Max Comfort for a reason. Also included is an optional V Pad to eliminate that last little bit of light leak around the bridge of the nose that plagues some pilots. Throw out that old, sweaty, ill-fitting goggle foam and get the NewBeeDrone Max Comfort Goggle Foam for DJI Goggles. Check out our other FPV goggles and accessories! Specifications 23mm at its thickest. 14mm at its thinnest. Includes 1x  NewBeeDrone Max Comfort Goggle Foam for DJI Goggles 1x V Pad 1x Set of V Pad Velcro Squares

Read more less

Are you tired of the stock DJI goggle foam that leaks light or is just plain uncomfortable?  Introducing the NewBeeDrone Max Comfort Foam Cushion for DJI Goggles 2, designed to provide comfort and optimal functionality. With the foam's increased height at both sides eliminates light leakage while its high compressibility maintains an optimal distance between your lens and your eyes. It also has an ergonomic shape to conform to your face and provide a snug fit, plus added height at the bottom to distribute the weight across your face instead of your nose. Enjoy clear visuals and a comfortable fit with the Goggles 2 max comfort foam cushion. Check out our other FPV goggles and accessories, and all our NewBeeDrone products! Features Easy to apply and remove. Eliminates light leak with included, optional V Pad for the bridge of the nose. Made out of extra comfortable Soft Touch NewBeeDrone Comfort Foam. Perfectly sculpted to fit all faces. The perfect thickness for comfort and goggle balance. Specifications 23mm at its thickest. 14mm at its thinnest. Color: Grey Includes 1x  NewBeeDrone Max Comfort Goggle Foam for DJI Goggles 2

Read more less

Are you looking to upgrade the feel of your new Fat shark HDOs, HD3s, Dominators, or Attitudes? Try the NewBeeDrone MaxComfort goggle cushion! Your stock foam not cutting it, or beaten and tired? Experience the soft touch of NewBeeDrone's new foam. Check out our other FPV goggles and accessories! Specifications Foam Thickness: 11mm Includes 1x NewBeeDrone Max Comfort Foam Cushion for Fatshark Goggles

Read more less

Introducing the NewBeeDrone Max Comfort Foam Cushion for HDZero Goggles, designed to provide comfort and optimal functionality. With the foam's increased height at both sides eliminates light leakage while its high compressibility maintains an optimal distance between your lens and your eyes. It also has an ergonomic shape to conform to your face and provide a snug fit, plus added height at the bottom to distribute the weight across your face instead of your nose. Enjoy clear visuals and a comfortable fit with the HDZero Goggles cushion. Check out our other FPV goggles and accessories, and all our NewBeeDrone products! Features Easy to apply and remove. Made out of extra comfortable, Soft Touch NewBeeDrone Comfort Foam. Perfectly sculpted to fit all faces. The perfect thickness for comfort and goggle balance. Specifications 8.5mm thickness Color: Black Includes 1x NewBeeDrone Max Comfort Foam Cushion for HDZero Goggles

Read more less

Plagued with the current generic 2.0 plugs on the market, we got tired of being able to plug the connector in backward and possibly ruin your FC, so we made the best one possible.The Nectar Connector is a custom mold design with thicker plug walls that makes it literally impossible to plug a lipo in backward without breaking the battery side plug first. Never again will you fear if you have plugged in the right way and risk burning your FC. The transparent plug design gives a great style and also lets you see the condition of your pins when troubleshooting power issues. If you even look closely enough you can see the NBD letters! Check out all our pigtails and connectors as well as the rest of our NewBeeDrone selection! Includes 1x NewBeeDrone Nectar Connector PH2.0 Clear Battery Lead

Read more less

The Nectar Connector Gold Plated Solid Pin features brass pins coated with a 24K gold layer. This design ensures an optimized power conversion for top-notch performance. With a continuous current of 9A at 4V, the pin temperature remains stable at 60°C after 5 minutes and can withstand up to 15A for 10 seconds with a max temperature of 120°C. This continuous power supply reduces power losses caused by heat and stops your board from overheating, making for smoother and longer-lasting flights. Check out all our pigtails and connectors as well as the rest of our NewBeeDrone products! Specifications Wire Length: 45mm Wire Gauge: 26AWG Weight: 0.6g (ea.) Connector: PH2.0 - Red Includes 1x NewBeeDrone Nectar Pigtail Connector Gold Plated Solid Pin PH2.0 26AWG 45mm Red Battery Lead - 5 Pack

Read more less

All batteries must be shipped by a ground shipping method. NBD is excited to introduce the Nitro Nectar Gold Series HV Lipo Battery Series! They use a different battery packaging technology that provides a better discharging rate for those who like to push the limit! They tested these batteries with their powerhouse 1S craft, the AcroBee BeeBrain BL BNF and they are built to keep up with the demand of raw thrust!  After 3 months testing, NewBeeDrone is ready to bring them to the market for whoop pilots across the world! Lightweight, durable and plenty of power to bring home the Gold! Check out our 1S battery selection, and all our NewBeeDrone gear! NOTE: These packs are designed to deliver a major amount of power!  With the discharge rate that gives these packs such power, you will feel pack sag much later than normal packs.  We suggest setting the low voltage reading to 3.5v and bringing it in to land at 3.3v.  You are able to fly below 3.3v but that may result in battery degradation. You will need a high voltage capable charger, such as our brand new Nectar Injector portable USB powered charger. Specifications Cell count: 1 Nominal voltage: 3.8V Max voltage: 4.35V Capacity: 300mah Continuous discharge rating: 40C Max discharge rating: 80C Dimensions: 62mm x 10.5mm x 6.5mm Weight: 8.10g (+/-1%) Plug: PH 2.0 or GNB27 Wire Length: PH2.0 None, GNB27 50mm Watt hours: 1.14 Wh Includes 1x Nitro Nectar Gold 3.8V 1S 300mAh 30/60C LiHV Whoop/Micro Battery

Read more less

Ring Magnets for an FPV drone? Yes! Team NewBeeDrone put in countless hours to figure out how they could improve upon the Smoov-Certified freestyle motor which provides super smooth performance for freestyle and cinematic FPV while maintaining the durability and precision machining you've come to expect from NewBeeDrone. NBD are proud to say that we have done just that... again!The NewBeeDrone Smoov V2 2306.5 1750Kv Motor has not only improved upon our very successful V1 motor, it is now 3 grams lighter! It's constructed with 7075 aluminum alloy unibell design for the best structural rigidity and comes with fully molded ring-style magnets. Ring motors are also easier to clean than traditional motors. Unlike traditional square magnet motors, the Smoov ring magnets have no physical spacing between the magnets to allow for quick and easy removal of dirt, grime, or anything you can manage to get into them.Making a fully molded ring magnet with high magnetic flux density is at the heart of the design. NBD has developed a ring magnet that can hold up to N48SH levels! Ring magnets are typically used in camera gimbals because they need to operate silky smooth. Traditional gimbal motors are super smooth but they lack punch and power. The Smoov V2 motors have both, along with improved balancing and better performance. The Smoov V2 ring magnet motors have more punch, less weight, higher strength, and they're Smoover than ever! This motor is also available in 2450Kv! Check out our vast brushless motors selection, and all our NewBeeDrone products! Features Single-winding with 0.15mm lamination stator. Ring Magnet N48SH NdFeB V2 Super Smoov performance for freestyle and cinematic purpose Japanese NSK Bearing 7075 Aluminum 6" prop compatible with Motor Limit Settings in BetaFlight Specifications Input Voltage: 6S Stator Diameter: 23mm Stator Height: 6.5mm Shaft Diameter: 5mm Motor Dimension (Dia.*Len): Ø29.4mm*31.6mm Weight: 36g(include cable) Wire Size: 20AWG 150mm Bearing: NSK/NMB 684ZZ  Ø9×Ø4×L4mm Includes 1x NewBeeDrone Smoov V2 2306.5 1750Kv Motor 1x Hardware Pack

Read more less

Ring Magnets for an FPV drone? Yes! Team NewBeeDrone put in countless hours to figure out how they could improve upon the Smoov-Certified freestyle motor which provides super smooth performance for freestyle and cinematic FPV while maintaining the durability and precision machining you've come to expect from NewBeeDrone. NBD are proud to say that we have done just that... again!The 2306.5 Smoov V2 ring magnet motor has not only improved upon our very successful V1 motor, it is now 3 grams lighter! It's constructed with 7075 aluminum alloy unibell design for the best structural rigidity and comes with fully molded ring-style magnets. Ring motors are also easier to clean than traditional motors. Unlike traditional square magnet motors, the Smoov ring magnets have no physical spacing between the magnets to allow for quick and easy removal of dirt, grime, or anything you can manage to get into them.Making a fully molded ring magnet with high magnetic flux density is at the heart of the design. NBD has developed a ring magnet that can hold up to N48SH levels! Ring magnets are typically used in camera gimbals because they need to operate silky smooth. Traditional gimbal motors are super smooth but they lack punch and power. The Smoov V2 motors have both, along with improved balancing and better performance. The Smoov V2 ring magnet motors have more punch, less weight, higher strength, and they're Smoover than ever! This motor is also available in 1750Kv! Check out our vast brushless motors selection, and all our NewBeeDrone products! Features Single-winding with 0.15mm lamination stator. Ring Magnet N48SH NdFeB V2 Super Smoov performance for freestyle and cinematic purpose Japanese NSK Bearing 7075 Aluminum 6" prop compatible with Motor Limit Settings in BetaFlight Specifications Input Voltage: 4S Stator Diameter: 23mm Stator Height: 6.5mm Shaft Diameter: 5mm Motor Dimension (Dia.*Len): Ø29.4mm*31.6mm Weight: 36g(include cable) Wire Size: 20AWG 150mm Bearing: NSK/NMB 684ZZ  Ø9×Ø4×L4mm Includes 1x NewBeeDrone Smoov 2306.5 2450Kv Motor 1x Hardware Pack

Read more less

Used to be everyone had a pile of these laying around. If you're flying a linear dipole on your whoop and wondering where your old rubber ducky flew off to, we've got you covered! NewBeeDrone explains it simply in their Honey Patch listing: "If you are using a linear whip antenna on your micro quad and using a circular antenna to receive you would be experiencing a 3db loss due to the mixed polarization signals, for each 3db drop in signal that is a half in power so effectively your 25mW vtx will only be seen as transmitting 12.5mW." Just a simple linear omni antenna, these work great when paired with a linear patch like the NewbeeDrone Honey Patch or the Menace Bandicoot on your diversity module. The downside of linear polarization is its susceptibility to multi-path interference. Locations with lots of metal and hard surfaces will tend to reflect lots of RF causing a noisy FPV feed. The ImmersionRC rapidFIRE module is terrific at handling this type of interference. Check out all our linear antennas as well as the entire receiver antenna selection! Features 360° rotation and 90° bend articulation of easy mounting and positioning Knurled SMA for easy installation and removal Cheap! Specifications Gain: 3 dBi Type: Omni-directional Dipole Polarization: Linear Vertical VSWR: 1.8:1 Frequency: 5100~5800MHz Size: L105xW10xH10mm Weight: 14g Includes 1x Omni-Directional 5.8GHz Articulated SMA "Rubber Ducky" Antenna - Linear

Read more less