TFL's new Bearing Clamp Oiler. Just tighten and attach an oil source and you will have easy and convenient lubrication during run time. Specs:- For .250" 6.35mm Cables- Bearing Diameter: 6.85mm- Water Fitting: M5- Length: 20mm (0.79")- Width: 30mm (1.18")- Height: 30mm (1.18")- Weight: 19.84g (0.7 Oz)
Aluminum with anodized silver servo mount for standard size servos(for example Futaba S3003 etc.).Servo width mounting plate is adjustable.All nuts and screws included. Servo NOT included.
Notes: For use in a rc boat this will require either gluing it directly to the hull or a wooden base to screw into. Some servos will require slight modifications if there are bulges or wires sticking out of the sides.Will fit upto 43mm wide servo.
Carbon, Water cooled heavy duty motor mount for 36mm motors.Fits 36mm diameter motors that are 60mm or longer in length.Both water-cooled and adjustable. The rear motor clamp helps carry the weight of the heavier/longer 36mm motors. Angle is adjustable to allow straight alignment with propeller cable.The anodized aluminum mounting plate with extended Carbon Fiber mounting stands to distribute the weight of the motor over a larger area for added strength. The mounting plates have holes drilled in the bottom to allow the epoxy to flow into them to make a superior bond to the hull. This mount can fit a flat mounting area like a rigger or hydro, or a deep vee.
Applications:Fits most 36mm motors that are 60mm or longer.For example Feigao, Nemesis, Hacker 540XL motors. Tp36xx, Leopard 3660, 3674Will fit up to a 50mm long water jacket.Measures:Total width of 58mm including the mounting stands.Metal center mounts measure 54mm wide.Requires you to provide motor mounting screws.Comes with mount only. Motor and water jacket only in pictures for display purposes.
OSE-80402, OSE Auto Bailer
Use this to help get rid of water in you hull. The aluminum bailer has a small plastic ball that moves to allow water to exit your hull while your running your boat, but when your boat is at rest the outside water pressure pushes the ball into a seal that closes the hole.Measures:approx 25mm long x 10mm diameter.
CNC cut aluminum mount works well in narrow areas like catamaran sponsons where there isn't enough room for an adjustable mount. The fixed angle is ridged enough for the longest of 56mm motors. Shown in picture with Leopard 5692 (not included) and Ham-leopard-56L water jacket (not included).Specifications:Motor holes are 30mm apart.Holes for 4mm screws.67mm (2.64") wide.Weight 3.4 ounces Available in Black or Silver Colorations
Requires:Installation, Glue and fiberglass to fix the mount into the hull. Motor mounting screws.
PRO-MOD-CARB, Gizmo's Racing Modified Walbro WT-257 Carburetor
Gizmo's Racing modified Walbro WT-257 carburetor is bored and the mouth of the carb has a radius inlet to allow a smooth and even entry of air into the intake duct with the flow stream adhering to the carb walls.
The flow-contoured entry is designed to reduce boundary layer disturbance as high velocity air enters the intake path. Results include improved air stability and increased engine performance.
**The carburetor also comes with the needle clamp and stainless Button Head screws.**
NOTE: THESE ARE PORTED ON A CNC MACHINE SO WE CAN GET PRECISE BORE SIZE EVERY TIME.
RCE16247-Function Charge Adapter to Male 4mm Bullets-300mm Wire
Racer's Edge provides an ideal solution for enthusiasts with multiple models using batteries with various connectors. This convenient charging squid comes equipped with virtually every possible connector that a modeler may require. Plugs included: Tamiya, Deans, XT60, JST, EC3, universal receiver pack, and if we've forgotten anything there is a pre-tinned pair of wires awaiting installation of your favorite connector.
RCE6405, Racers Edge Metal Front CVD Shafts & Pins & M4 Lock Nut for Slyder
Metal Front CVD Shafts & Pins & M4 Lock Nut for Blackzon Slyder
This product was added to our catalog on October 28, 2021
