The iFlight 5V/12V Step Down Micro BEC features high-efficiency synchronous rectification and the ability to step down from a wide input voltage range of 2-8S(5-36V) and provide a lower stable output voltage. It's an incredibly compact solution for still being able to provide 3 amps at 5 volts, and 2 amps at 12 volts.
For those looking for something even smaller and only needing 5V 2A output from 3-6S input, may we suggest the iFlight 3-6S Micro 5V 2A BEC.
Check out the Rest of our iFlight product range and PDB/BEC selection while you're at it!
Features
Step-down Switch Mode
High-efficiency Synchronous Rectification
Wide Input voltage range
Voltage output can be 5V or 12V* (default 5V)
*When the "ON-12" Jumper pads are shorted, the output voltage is 12V 2A. When open, the output voltage is 5V 3A. See enlarged image below.
Specifications
Input voltage: 2-8S(5-36V)
BEC Output: 5V/2A, 12V/3A (default 5V/2A)
Dimensions: 12x14x4.5mm
Pin Spacing: 2.55mm
Weight: 1.8g
Includes
1x iFlight Micro 2-8S BEC - 5V/12V Output
1x Connecting Cables Set
Voltage Switch Jumper:
Your motors and ESCs generate electrical noise that can be detrimental to your video quality. The most common symptoms of electrical noise are lines and dots in your FPV feed, especially when accelerating. These little filters can help clean up the noisy power running into your sensitive FPV electronics.
Take a look at our PDB & BEC selection, as well as the rest of our iFlight offerings.
Features
Perfect for sensitive FPV- and RC components in a single battery setup.
Both the negative and positive leads are filtered (common mode)
Suitable for setups up to 36V
Reduces DC-DC switcher supply ripple and helps clean noisy power from a shared battery.
Reduce the effects of interference radiated through the air and noise conducted via the power wires.
Help attenuation most of the high-frequency power supply noise and interference.
Suppress the noise in the power getting to your FPV setup (e.g. your VTX and FPV camera).
Built-in Reverse Polarity protection
Very low voltage drop
Specifications
Input Voltage: 5-36V
Max. Input Current: 3A
Weight: 1.1g
Includes
1x iFlight 5-36V LC Filter Module
Replacement arms for the iFlight AOS 5 EVO 5" Frame Kit.
Check out all of our 5" frames and our selection of iFlight gear!
Specifications
Arm Thickness: 6mm
Weight: 13.9g
Includes
1x iFlight AOS 5 EVO 5" Replacement Arms
The iFlight AOS 7 EVO 7" Frame Kit is perfect for freestyle drone racing. Constructed with 8mm arm thickness for superior durability and reliability, the kit features 25.5x25.5 or 20x20mm stack mountings in the front, center, and rear. It fits the DJI O3 Air Unit, Caddx Vista, or HDZero Freestyle VTX and both 20mm (DJI and O3 camera) and 19mm (micro-sized) cameras. Standoffs, frame, and screws are included.
The AOS 7 builds on the scientific approach used to design the AOS 5 and AOS 5.5, extending the benefits of those designs to the 7" class. Until now, 7" quads have been primarily used for long-range cruising and have never been able to match the performance of 5" quads for aggressive freestyle flying. The AOS 7 EVO 7" frame kit is here to break that conception.
The latest version of this frame is the AOS 7 EVO. It has an updated camera, top and bottom plates to support the DJI O3 Air Unit, and all other 19-20mm FPV cameras.
With the V1.2 updated side plates and silicone dampers. Frame kit upgrade to the top plate with two antenna cutouts. Making this frame more ideal and suited for the DJI O3 Air Unit.
Check out all of our 7" frames and our selection of iFlight gear!
Make sure to check out our other O3 compatible frames!
Features
25.5x25.5 or 20x20mm stack mountings in the front, center and rear.
Fits the DJI O3 Air Unit, Caddx Vista or HDZero Freestyle VTX perfectly
Fits both 20mm (DJI and O3 camera) and 19mm (Micro sized) cameras
Standoffs, frame and screws included
Specifications
Product Name: AOS 7 EVO V1.2 Frame Kit
Frame wheelbase: 293mm
Frame Dimension: L228xW284xH34.5 mm
Arm Thickness: 8mm
Top Plate Thickness: 2mm
Bottom Plate Thickness: 2mm
Upper Plate Thickness: 2.5mm
Motor Mounting: 19x19mm
VTX Mounting: 20x20/Φ2mm / 25.5x25.5/Φ2mm
Weight: 290±5 grams (Included TPU Parts)
Includes
1x iFlight AOS 7 EVO 7" V1.2 Frame Kit
1x TPU Parts
4x Motor Wire Shield Tube
1x Screw Bag
2x Battery Strap
Replacement arms for the iFlight AOS 7 EVO 7" Frame Kit
Check out all of our 7" frames and our selection of iFlight gear!
Specifications
Arm Thickness: 8mm
Weight: 29.4g
Includes
1x iFlight AOS 5 EVO 5" Replacement Arms
The new iFlight Blitz 30x30 25-1000mW+ 5.8GHz VTX - MMCX is capable of blasting over 1000mW from a super durable machined aluminum case!
Check out all our VTXs as well as our entire iFlight selection!
Features
Stable output power
4 Power levels up to 1600mW*
40 Channels (including Raceband)
Fast frequency lock, no startup interference with other pilots
Built-in output power self-check functionality
VTX telemetry with IRC Tramp protocol
Specifications
Input voltage: 7V～36V
Interface: MMCX
Power levels: PIT/25mW/400mW/800mW/1600mW
Channels: 40 (including Raceband)
Mounting pattern: 30.5x30.5mm/Φ3
VTX telemetry: IRC Tramp
IRC Tramp VTX table values: 25mW/400mW/800mW/1600mW
Weight: 18.9g
*VTX is set to 25mW by default! Power levels above 25mW require a HAM license or have to be approved by local authorities! Please ensure you're flying legal frequencies and use iFlight's prepared Betaflight VTX tables according to your region.
Betaflight IRC Tramp Configuration: Please download VTX tables here
Includes
1x iFlight Blitz 30x30 25-1000mW+ 5.8GHz VTX - MMCX
Wiring Diagram
Please note, this Flight Controller is based on the ATF435 chip opposed the the F4's and F7's most of the community is used to. Downloading new drivers and using custom targets may be required.
As long as your BetaFlight 10.10 you should be good to go!
The iFlight Blitz ATF435 Stack/Combo provides dependable performance and efficient control of your 2-6S powered quadcopter. This 30x30 stack/combo features an ATF435 FC and 55A 8Bit 4in1 ESC to give you responsive controls and reliable power delivery. Fly worry-free and explore new heights. This flight controller comes with plug-in ports for 9V VTXs, LED/Buzzer, receiver, camera, & the ESC. The NEW ATF processors allow for a product like this, a 60-dollar stack that is feature-rich and comes with a 55Amp ESC, which is perfect for those amp-hungry builds.
Check out our other 30x30 Stacks & Combos as well as our entire iFlight selection!
To configure download ATBetaflight and if that does not automatically connect, here are virtual com port drivers. Future versions of Betaflight will fully support these boards.
Specifications
iFlight Blitz ATF435
MCU: AT32F435CGU7
Gyro: BMI270
Barometer: DPS310
OSD Chip: AT7456E
Flash: 32MB (Blackbox flash)
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C serial: SDA / SLA pads
Smartaudio / IRC Tramp VTX protocol supported
LED controller: Yes
Beeper pad: Yes
Firmware target: IFLIGHT_BLITZ_ATF435
Mount pattern: 30.5x30.5mm / 4mm PCB hole diameter
Dimensions: 36.5x35 mm
Weight: 7.8g
BEC: 5V 2.5A / 9V 2A
Blitz E55S ESC
Mounting Holes: 30.5x30.5mm/Φ4mm
Weight: 14.7g
Supports 2-6S lipo input
MCU: G071
Constant: 55 Amps
Burst: 65 Amp
Current sensor: Yes
BEC: No
Current rate: 200
Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
Target: Q-H-25 16.7(BlheliS) / Bluejay Q-H-50 (Bluejay)
Include
1x iFlight Blitz ATF435 E55S 2-6S 30x30 Stack/Combo (ATF435 FC/ 55A 8Bit 4in1 ESC)
Another great addition to iFlight's ESC lineup. With 2-6S input, up to 55A bursts, and an integrated capacitor, the iFlight BLITZ E45S 45A 2-6S 30x30 4in1 ESC is a great value option for a 30x30 ESC.
Check out all our 30x30 ESCs and all out iFlight gear selection!
Specifications
Input Voltage: 2-6S
Max. Continuous Current: 45A
Max. Burst Current: 55A
Firmware: BLHeli_S
MCU: BB21
Target: QH-40 16.7
BEC: No
Telemetry Output: No
Current Sensor: Yes
Current Sensor Scale: 200
Dimensions 40.5x42x6.5mm
Mounting Dimesions: 30.5x30.5mm Φ4mm
Weight: 14.7g
Includes
1x iFlight Blitz E45S 45A 2-6S 30x30 4in1 ESC
1x Wiring Set
The next generation of ESCs from iFlight has arrived. Currently being used in their BNF quads such as the Chimera7 Pro BNF. These new 55 Amp BLHeli 32 Blitz 4-in-1 ESCs can handle even the most amp-hungry motors.
Check out all our 30x30 ESCs and all our iFlight gear selection!
Specifications
Input Voltage: 2-6S
Max. Continuous Current: 55A
Max. Burst Current: 65A
MCU: G071
BEC: No
Firmware: BLHeli32
Current Sensor: Yes
Target: IFLIGHT_BLITZ_G2
Mounting Dimensions: 30.5x30.5mm/Φ4mm
Dimensions: 35x42mm
Weight: 15.3g
Includes
1x iFlight Blitz E55 55A 2-6S 30x30 4in1 ESC
1x Wiring Set
Another great addition to iFlight's ESC lineup. With 2-6S input, BLHELI32 firmware, up to 60A bursts, and an integrated capacitor, the iFlight BLITZ E55 55A 2-6S 20x20 4in1 ESC is a great value option for a 20x20 ESC.
Check out all our 20x20 ESCs and all our iFlight gear selection!
Features
V1.3 added metal mosfets to the bottom of the ESC for better heat dissipation and performance.
Specifications
Input Voltage: 2-6S
Max. Continuous Current: 55A
Max. Burst Current: 60A
MCU: G071
BEC: No
Current Sensor: Yes
Firmware: BLHeli32
Target: IFLIGHT_BLITZ_G1
Mounting Dimensions: 20x20mm/Φ4mm
Dimensions 35x42mm
Weight: 11.3g
Includes
1x iFlight Blitz E55 V1.3 Mini 32bit 55A 2-6S 20x20 4in1 ESC
1x Wiring Set
BLITZ E80 BLHeli Dshot600 Single ESC was designed to give your motors smooth power with great stability and durability. The 32bit 48mHz G071 MCU and 11 pieces TDK MLCC total 240UF Low ESR capacitors bring faster-responding speed and a smoother flying experience.
Check out all our individual ESCs and all our iFlight gear!
Features
2-8S input
80A 8 layers 4OZ copper PCB, better operating load capacity;
11 pieces TDK MLCC total 420UF Low ESR capacitors, lower ripple, and more stable.
Top grade NTMFS5C430NL MOSFET, stable and reliable;
A 3528 LED for power- on display;
Rational layout, large soldering pad, countersinks, and semicircle orifices enable each layer to be energized after power-on.
Specification
Dimension: 40x17mm
Weight: 9.5g without wire
Supports 2-8S lipo input
STM32G071 MCU, 48Mhz Runs BLHELI 32.X Firmware
Capacitance: total 240UF Low ESR
BEC: No
Supports: DShot DShot150/300/600/MultiShot/OneShot PWM Drive
Target: IFLIGHT_BLITZ_G2
Supports
Current Sensor
Telemetry output
Motor Timing
Brake on Stop
Includes
1x BLITZ E80 Single ESC
1x 50V 470uf capacitor
1x Power cables & ESC signal wire set
iFlight Blitz F411 1S 5A Toothpick/Whoop Flight Controller w/ 25-50mW VTX & ELRS RX is perfect for all of your lightweight builds. It is a Flight Controller, ESC, Receiver and VTX all in one little board weighing in at 4.8g. Now using ExpressLRS with a built-in ELRS ceramic antenna!
Check out all our whoop flight controllers, and all our iFlight Products!
Specifications
Input Voltage: 1S
MCU: STM32F411
Gyro: BMI270
Built-in Receiver: SPI ExpressLRS 2.4G
Receiver antenna: 2.4GHz SMD ceramic antenna
VTX: PIT/25/50mW
FC Firmware: IFLIGHT_BLITZ_F411RX
Current: 5A continuous and peak 6A (3 seconds)
Signal Support: Dshot, Oneshot, Multishot
ESC Firmware: O-H-30 BLS 16.8 (Supports BLHeliSuite)
Dimensions: 29x29mm, compatible w/ standard whoop framest
Weight: 4.8g
Includes
iFlight Blitz F411 1S 5A Whoop Flight Controller w/ 25-50mW VTX & ELRS RX
4x M2 Rubber Damper
1x Whip antenna
Wiring Diagram
The new iFlight blitz series offers stellar performance at an affordable price. With an F7 processor and high quality BMI270 gyro, this FC is all you could ever need for daily cruising or even hardcore freestyle and racing!
Check out our other 20x20 FCs, as well as the rest of our iFlight selection!
Specifications
MCU: STM32F722
Gyro: BMI270
Barometer: DPS310
OSD Chip: AT7456
Blackbox: 16MB
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C: SDA / SLA pads
LED: Yes
Beeper: Yes
Firmware Target: IFRC-IFLIGHT_BLITZ_F722
Mounting Pattern: 20x20mm
Dimensions: 30.5x27mm
Weight: 5g
Includes
1x iFlight Blitz F7 Mini V1.1 20x20 Flight Controller
Wiring Diagram
The new iFlight blitz series offers stellar performance at an affordable price. With an F7 processor and high quality BMI270 gyro, this FC is all you could ever need for daily cruising or even hardcore freestyle and racing!
Check out our other 30x30 FCs, as well as the rest of our iFlight selection!
Specifications
MCU: STM32F722
Gyro: BMI270
Barometer: DPS310
OSD Chip: AT7456E
Blackbox: 32MB
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
BEC: 5V 2.5A
I2C: SDA / SLA pads
LED: Yes
Beeper: Yes
Firmware Target: IFRC-IFLIGHT_BLITZ_F722
Mounting Pattern: 30.5x30.5mm
Dimensions: 36.5x35mm
Weight: 7.8g
Includes
1x iFlight Blitz F7 V1.1 30x30 Flight Controller
Wiring Diagram
The next generation of the iFlight Blitz F722 E55 2-6S 30x30 Stack/Combo (F722 FC/ 55A 32bit 4in1 ESC) have arrived. These new flight controllers are equipped with a plug and play connectors making connecting your video transmitter, radio receiver, and other periphery sensors a breeze.
They also make diagnosing issues in the field much easier with status indicator LED's that let you know in seconds if you are having a problem with the 3.3V, 5V, or VBat. Coupled with iFlight's new 55 Amp BLHeli_32 Blitz 4-in-1 ESC, this stack can handle even the most amp hungry motors.
Check out our other 30x30 Stacks & Combos as well as our entire iFlight selection!
Specifications
Blitz F722
MCU: STM32F722
Gyro: BMI270
Barometer: DPS310
OSD Chip: AT7456E
Blackbox: 32MB (Blackbox flash)
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C: SDA / SLA pads
LED: Yes
Beeper: Yes
Firmware Target: IFRC-IFLIGHT_BLITZ_F722
FC Mounting Pattern: 30.5x30.5mm
Dimensions: 36.5x35mm
Input Voltage: 2-6S
BEC: 5V 2.5A
E45 4in1 ESC
Input Voltage: 2-6S
Max. Continuous Current: 55A
Max. Burst Current: 65A
Firmware: BLHeli 32
MCU: G071
BEC: No
Current Sensor: Yes
Target: IFLIGHT_BLITZ_G2
Mounting Dimensions: 30.5x30.5mm/Φ4mm
Dimensions 35x42mm
Includes
1x iFlight BLITZ F7 V1.1 30x30 Flight Controller
1x iFlight BLITZ E55 55A 2-6S 30x30 4in1 ESC
1x Wiring Set
Wiring Diagram
The iFlight BLITZ M10 GPS w/ Compass provides reliable positional and directional data for your quad. Its advanced compass and GPS module allow for precise coordinates and real-time flight information for optimal navigation. This high-performance unit helps ensure safe and accurate flight paths for your craft. Always keep a quad when you add a GPS!
Check out our other GPS modules, as well as the rest of our iFlight Products
Features
Using the latest UBLOX M10 chip, lower power consumption, faster satellite search speed.
Built-in high precision compass QMC5883L.
Built-in Faraday capacitor, with 1-10Hz positioning update rate, which makes GPS have faster startup speed and satellite receiving speed.
18x18mm ceramic antenna provides the best balance and performance for current GPS modules, low power consumption, strong signal and light weight.
On-board LNA low noise amplifier and RF filter provide excellent working environment for GPS module.
Up to 10HZ refresh rate.
Built-in Flash, users can set GPS parameters by themselves using U-center or other software, configuration modification will be stored to Flash, no loss of parameters after power failure.
Pin Definitions
VCC: system main power supply, supply voltage is 5V, current is about 40mA when working
GND: Ground
RXD: data input
TXD: Data output
SDA: Serial Data - I2C Master/Slave Data
DCL: Serial Clock - I2C Master/Slave Clock
Light Indicator
Blue light, TX light, the blue light blinks on power up, indicating that there is data output.
Red light, PPS light, not positioned red light is not lit, 3D positioning, the red light began to flash
Specifications
Compass module: QMC5883L
Baud Rate: 4800bps-115200bps (Default - 115200bps)
Sensitivity: Tracking: -167dBm
Cold start: 26s
Hot start: 1s
Maximum height: 50000m
Maximum speed: 500 m/s
Speed accuracy: 0.05 m/s
Maximum acceleration: ≦ 4G
Refresh Rate: 10 Hz
GPS patch antenna size: 18x18 mm
Total dimensions: 20 x 21 x 6.5 mm
Weight: 5.2 g（±0.5g）
Input Voltage: 3.3-5.5 V, current 40mA
GPS pin definition: RX/TX UART
Compass pin definition: SDA/SLA
Includes
1x iFlight BLITZ M10 GPS & Compass (10th Gen)
1x Cable Set
Another great addition to iFlight's ESC lineup. With 2-6S input, up to 60A bursts, and an integrated capacitor, the iFlight BLITZ E55S is a great value option for a 20x20 ESC.
Check out all our 20x20 ESCs and all our iFlight gear selection!
Features
V1.1 added metal mosfets to the bottom of the ESC for better heat dissipation and performance.
Specifications
Input Voltage: 2-6S
Max. Continuous Current: 55A
Max. Burst Current: 60A
MCU: BB21
BEC: No
Current Sensor: Yes
Firmware: BLHeli_S
Target: QH-50 16.7
Mounting Dimensions: 20x20mm/Φ4mm
Dimensions 35x42mm
Weight: 11.3g
Includes
1x iFlight Blitz Mini E55S Mini (v1.1) 8Bit 55A 2-6S 20x20 4in1 ESC
1x Wiring Set
The new iFlight Blitz Mini F722 E55 2-6S 20x20 Stack/Combo (F722 FC/ 55A 32bit 4in1 ESC) series offers stellar performance at an affordable price. With an F7 processor and high-quality BMI270 gyro, this FC is all you could ever need for daily cruising or even hardcore freestyle and racing! And with these new 55 Amp BLHeli 32 Blitz 4-in-1 ESCs, you can handle even the most amp-hungry motors. On the Bottom of the ESC, for the the version prior it used to have regular MOSFETS, but now with the V1.3 they come with Metal Mosfets!
Check out our other 20x20 Stacks & Combos as well as our entire iFlight selection!
Features
Improved circuit design, better components and lower electrical noise!
DJI HD VTX Connector (Plug-and-Play / No soldering required)
FC indicator LEDs for visual debugging
BLITZ Mini E55 4-IN-1 ESC V1.3 - Metal Mosfets (Jan-28,2023)
Specifications
Blitz Mini F722
Input Voltage: 2-6S
MCU: STM32F722
Gyro: BMI270
Barometer: DPS310
OSD Chip: AT7456
Blackbox: 16MB
UARTS: 6
Motor outputs: 4x (SH1.0 connector)
I2C: SDA / SLA pads
LED: Yes
Beeper: Yes
Firmware Target: IFRC-IFLIGHT_BLITZ_F722
FC Mounting Pattern: 20x20mm
Dimensions: 30.5x27mm
Blitz Mini E55 4in1 ESC (v1.3
Input Voltage: 2-6S
Max. Continuous Current: 55A
Max. Burst Current: 60A
MCU: G071
BEC: No
Current Sensor: Yes
Firmware: BLHeli32
Target: IFLIGHT_BLITZ_G071_01
Mounting Dimensions: 20x20mm/Φ4mm
Dimensions 35x42mm
Weight: 11.3g
Includes
1x iFlight Blitz F7 Mini V1.1 20x20 Flight Controller
1x iFlight Blitz Mini E55 V1.3 32Bit 55A 2-6S 20x20 4in1 ESC
1x Wiring Set
Wiring Diagram
Introducing the BOB57, a 6" cinematic long-range quad pre-installed with the all-powerful DJI O3 system for crystal clear image quality. This quad aims to best of 5" and 7", hence the name BOB57. This quad is DJI PNP, meaning it does not come with a receiver, meaning you need to install your receiver. However, if you have the DJI FPV Remote Controller 2, you can bind to the O3 Air Unit. This quad also comes with a GPS pre-installed, allowing all the marvelous features a GPS allows you. The BOB57 comes with XING2 2506 motors with a rated KV 1500, designed around 6S power.
The iFlight BOB57 is a long-range HD drone that was designed in collaboration with pilot & videographer Ellis van Jason. The team crafted this cinematic 6-inch drone that ensures agility and flight time while combining the advantages of both 5-inch and 7-inch drones for both cinematic and freestyle flights.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products
Features
Hybrid motor design optimized for that can be used with both bi-blade and tri-blade 6" propellers.
High-end GPS is used to minimize the risk of failure during proximity flights
Long backbone with enough space up to fit 3000mAh 6S batteries
Solid antenna mount for less oscillations when using long antennas
Gladiator shell protects from dust and water droplets
ESCs with built-in spike absorbers for more reliability
Built-in BEC to directly power a GoPro camera
9-minute flight time with 3000mAh 6S Lipo
Front-mounting XT-60
DJI O3 Air Unit
VERSATILE BODY
The Body is designed to carry small to large batteries for agile or long-range missions.
SMART XT60 AND USB-C PLUG
The XT60 plug is located in the front to gain more space. With the USB-C plug you can directly power your GoPro/Action Cams.
OPTIMIZED MOTOR AND PROPS
The Motor is designed for 6inch to give both great performance and efficiency. The prop is specifically optimized for this drone.
RELIABILITY
The BOB57 comes with a shell that protects against hits, droplets, and dust. It also has a high-quality GPS and components for more reliability, like a spike absorber & extra capacitor.
PRE-TUNED AND PRE-SETUP
Don't worry about tuning, iFlight did that for you already! A basic PID and Filter tuning were applied for a great flight experience!
Links
Ellis van Jason Tune Setup
Specifications
Product Name: BOB57 O3 6S HD BNF
FC: BLITZ F722
ESC: BLITZ E55 55A 4-IN-1 ESC
Video Transmission: DJI O3 Air Unit
Frame: 280mm wheelbase
Motor: XING2 2506 motors
Prop: GEMFAN 6032-3 propellers
Takeoff Weight: Approx. 580 g
Dimensions (L×W×H)：226×166×34 mm
Max Speed: 180 Km/h (Manual Mode)
Maximum Takeoff Altitude: 7000 m
Max Hover Time: Approx. 8 mins (With 6S 1400 no load.)
Max Wind Speed Resistance: Level 7
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Antennas: 2 Antenna
GNSS: GPS+SBAS+Galileo+QZSS+Glonass
Video Transmission
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4 grams（headband included）
Dimensions (L×W×H): L32.5x W30.5xH 14.5mm
Communication Bandwidth： Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Includes
1x BOB57 6S HD BNF
2x Antennas
2x Battery pads
2x Prop(Pairs)
All batteries must be shipped by a ground shipping method.
Introducing iFlight's Defender 25, a sub-250 drone featuring the DJI O3 Air Unit. At 249g weight, Defender 25 doesn't require registration in most countries. The compact and lightweight design also make it easy to carry and store. It will be your best travel buddy to redefine your FPV adventure. The built-in 2.5-inch propeller guards were designed to fly boldly. You’ll experience a completely new creative freedom to fly whenever and wherever. The durable injection molded frame not only prevents damage to your motors or propellers but also protects the environment from small flight errors.
Equipped with the latest tech from DJI, the O3 Air Unit HD transmission system, the Defender 25 supports 4K video and shoots up to 155° super-wide FOV footage for stunning visuals. In addition, D-Cinelike color mode provides more creative freedom for color grading, allowing you to edit and adjust your footage.
They’ve also added a special vibration-damped camera mount to keep your raw footage as smooth as possible, as well as ensure good Gyro Data for the built-in or in-post camera stabilization.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Features
Optimized Landing Gear for Take-Off in Complex Environments
Built-in High-Performance video and Receiver Antennas
4K Stabilized Video with 155° Ultra-Wide Angle
Crash-Protected Quick-Release Battery
Countless Easy-to-Use Features
Ultralight and Free to Fly
Small and Mighty
Specifications
Defender 25
Product Name: Defender 25 4S HD
Flight Electronics: BLITZ D25 F7 AIO
Video Transmission: DJI O3 Air Unit
Frame: 112±2mm
Motor: Defender25 1404
Prop: Defender25 2525 props (2.5-inch)
Weight of the Aircraft: 180g
Takeoff Weight incl. 550mAh battery: ≤249g
Dimensions (L×W×H)：158x155x69mm
Max Ascent Speed: 6 m/s (Normal Mode, Sport Mode)
Max Descent Speed: 6 m/s (Normal Mode, Sport Mode)
Max Speed: 100Km/H (Manual Mode)
Maximum Takeoff Altitude: 200 m
Max Hover Time: Approx. 6 mins (with 550mAh battery), 10mins (with 900mAh battery)
Max Flight Distance: 2-3 km
Max Wind Speed Resistance: 80 Km/H (Level 5)
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Transmission Power (EIRP): FCC: < 33 dBm / CE: < 14 dBm / SRRC: < 30 dBm
Antennas: Dual Antennas
GNSS: N/A
Video Transmission
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4grams
Dimensions (L×W×H): L16.7×W103.9×H 81.3mm
Screen Size (single screen): 0.49-inch
Resolution (single screen): 1920×1080
Refresh Rate: Up to 100 Hz
Interpupillary Distance Range: 56-72 mm
Diopter Adjustment Range: -8.0 D to +2.0 D
FOV (single screen): 51°
Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz
Transmission Power (EIRP):
2.4 GHz: < 30 dBm (FCC), < 20 dBm (CE/SRRC/KC)
5.8 GHz [4]: < 30 dBm (FCC), < 23 dBm (SRRC), < 14 dBm (CE/KC)
Max Video Transmission Bitrate: 50 Mbps
Operating Temperature Range: 0° to 40° C (32° to 104° F)
Power Input: 7-9 V (1.5 A)
Recommended (Not Included)
iFlight Defender 25 Battery - 900mAh
Includes
1x iFlight BNF Defender 25 HD 4S 2.5" Cinewhoop w/ DJI O3 Air Unit and DJI Camera (Pre-Built, Tuned, and Tested)
1x Defender 25 550mAh Battery
1x Charging Adapter Board
2x Defender 25 2525 Props (pairs)
The iFlight Nazgul5 V3 6S 5" Freestyle Analog Quad is here! It includes the RaceCam R1 FPV Camera and Nazgul 5" tri-blade props, XING-E Pro 2207 motors, BLITZ F7 Flight Controller, BLITZ 1000mW+ VTX, and the BLITZ E45S 2-6S 45A BLHeli32 4-in-1 ESC. Boasting CNC aluminum camera mount with vibration-reduction silicone for increased protection. Great for freestyling and long-distance shots with your GoPro camera! The Nazgul5 Freestyle quad is a go-to gold standard for freestyle BNFs of great value made by the great people at iFlight. The Nazgul5 V3 is a 5" freestyle frame is made of super stiff carbon for minimal resonance.
+ High-quality parts+ Sturdy frame structure+ Generous mounting space+ Optimized for O3 Air Unit+ GoPro camera mount included
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Features
XING-E Pro 2207 motors and NAZGUL F5 props
5" version also fits 5.1" style propellers
Fits both 30.5x30.5 and 20x20 stacks
5mm arm design for more durability
Popular True-X configuration
LED illuminated logo
TPU crash-guards
Easy-Swap arms
Specifications
Product Name：Nazgul5 V3 6S Analog
FC: BLITZ F722 FC
ESC: BLITZ E45S 45A 4-IN-1 ESC
Video Transmission: BLITZ 1mW+ VTX
Frame: 245 ±2 mm wheelbase
Motor: XING-E Pro 2207 motors
Prop: Nazgul 5 inch propellers
Takeoff Weight: Approx. 435g / 660±10g (With 6S 1400mAh Battery)
Dimensions (L×W×H): 173×173×34±2 mm
Diagonal Distance: 245mm
Max Speed: 190 Km/h (Manual Mode)
Maximum Takeoff Altitude: 3200 m
Max Hover Time: Approx. 7.5 mins (No Load with 6S 1400mAh Battery)
Max Flight Distance: 5 km
Max Wind Speed Resistance: Level 7
Operating Temperature Range：-10° to 40° C (14° to 104° F)
Antennas: Single Antenna
Video Transmission System
Product Name: BLITZ Whoop 1mW+ VTX
Input voltage: 7V～34V
Interface: MMCX
Power levels: PIT/25mW/400mW/800mW/1600mW
Channels: 40 (including Raceband)
Mounting pattern: 30.5x30.5mm/Φ3
Lightweight: 18.9g (excluding antenna)
VTX telemetry: IRC Tramp
Betaflight IRC Tramp Configuration: Please download the attached VTX table for Betaflight!
RC Tramp VTX table values: 25mW/400mW/800mW/1600mW
Includes
1x Nazgul5 V3 6S Analog BNF
1x Antennas
2x Battery pads
2x Nazgul F5 Prop(Pairs)
The Nazgul5 HD V3 is loaded with lots of power and performance; it comes with the XING-E Pro 2207 6S motors, BLITZ F722 FC, and BLITZ E45S 45A 4-in-1 ESC, which makes this quad a must-have! Now with the DJI O3 Air Unit! The Nazgul V3 is one of the best freestyle frames for its value. The Nazgul5 V3 HD has been pre-tuned and set up with everything you need, all you need to do is bind-and-fly. The Nazgul5 V3 is a 5" freestyle frame made of super stiff carbon for minimal resonance.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Features
XING-E Pro 2207 motors and NAZGUL F5 props
5" version also fits 5.1" style propellers
Fits both 30.5x30.5 and 20x20 stacks
5mm arm design for more durability
Popular True-X configuration
LED illuminated logo
TPU crash-guards
Easy-Swap arms
Specifications
Operating Temperature Range：-10° to 40° C (14° to 104° F)
Max Wind Speed Resistance: 130 Km/H (Level 4)
Receiver: DJI BNF, ELRS
Dimensions (L×W×H): 180×180×80 mm
Max Speed: 130 Km/h (Manual Mode)
Video Transmission: DJI O3 Air Unit
Maximum Takeoff Altitude: 5000 m
Product Name：Nazgul5 V3 6S HD
ESC: BLITZ E45S 45A 4-IN-1 ESC
Max Hover Time: Approx. 8 mins
Motor: XING-E Pro 2207 motors
Takeoff Weight: Approx. 620 g
Prop: Nazgul 5 inch propellers
Diagonal Distance: 245mm
Frame: 255mm wheelbase
Max Flight Distance: 5 km
Antennas: 2 Antenna
FC: BLITZ F722
GNSS: N/A
Video Transmission
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4 grams（headband included）
Dimensions (L×W×H): L32.5x W30.5xH 14.5mm
Communication Bandwidth： Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Includes
1x iFlight BNF Nazgul5 V3 HD 6S 5" Freestyle Quad w/ DJI O3 Air Unit & Micro Cam - Choose Receiver
2x Nazgul 5 inch propellers (Set of 4)
2x Battery Pad
2x Antenna
After our very popular 3-inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.
Our all-new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here.
ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all-new 2205 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to its 3inch predecessor which gives a lot more room for a lot more fun. Our GPS-measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch-outs or light freestyle moves.
A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Note: Battery, GoPro, and GoPro mount are NOT included.
Check out our other pre-built quads, as well as the rest of our iFlight selection!
Features
High-performance True-AIO Board Beast Whoop F7 AIO 55A v2.0 to save weight and space
T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
Low Resonance frame construction (Less Jello, more Cinematic footage)
Pre-tuned with smooth freestyle settings
Butter smooth 2205 3200KV (4S)
ProTek35 Prop Guards V2.0
No Props or frame in view!
Pre-Tuned & Pre-Setup:
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning were applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, and activate Acro-Mode"
Specifications
Beast F7 V2 AIO FC
MCU: BGA-STM32F745
Gyro: BMI270
Blackbox: 8Mb Onboard Flash
BEC output: 5V 2.5A
Barometer: BMP280
Connector: Micro-USB
OSD: AT7456E
FC Firmware：IFLIGHT_F745_AIO_V2
Mounting pattern: 25.5x25.5mm φ3mm
Dimensions: 32.5x32.5mm
Weight: 8.5g
F7 55A 2-6S ESC
Current Sensor: Yes
Input: 2-6S LIPO
Current scale: 200
Constant: 55A
BLHeli: BLHeli-S
Telemetry: no
ESC Firmware: BlheliS G-H-30
Mounting pattern: 25.5x25.5mm/Φ3mm
Dimensions: 32.5x32.5mm
SucceX Mini Force 5.8GHz 600mW VTX
Power: PIT/25/200/400mW/600mW
Antenna interface: MMCX
VTX protocol: IRC Tramp
Output 40 channels.
Size: 29x29mm
Mounting pattern: 20x20Φ3/25x25 mmΦ2
Weight: 4g
Includes
1x ProTek35 Frame
2x Albatross RHCP RP-SMA 5.8g antenna
1x TPU Antenna holder
2x Nazgul 3535 propeller (Set of 4 - Color May Vary)
1x iFlight Lipo Strap 15x150mm (Color May Vary)
1x iFlight Lipo Strap 15x250mm (Color May Vary)
1x GoPro TPU bottom stand black (GoPro Protector not included)
The iFlight Commando 8 ExpressLRS Radio Transmitter is a game-style radio controller that comes with a built-in ExpressLRS module for best-in-class RF performance! Its compact size allows the user to easily carry it on trips or to the field. Full-featured and powerful, this is a great radio for any purpose.
Check out our iFlight collection and all our RC transmitters!
Features
Internal iFlight ExpressLRS (ELRS) transmitter (additional fan for cooling)
Market's lowest crystal frequency deviation (low packet loss, high-frequency stability)
Highest quality digital hall sensor gimbals for maximum precision
High-performance PCB Single and Dual Band (900/2400MHz) radio antenna
Inbuilt 4000mAh for up to 20h power (2x 2000mAh 18650 batteries)
Stock EdgeTX firmware with pre-installed Lua scripts
Several Gimbal Stick Ends available (stock 18mm)
Specifications
ExpressLRS 2.4GHz // Max Output 500mW
Radio Channels: 8
Input: Mini High Precision Digital Hall Gimbals with NMB bearings
Gimbal Stick Ends: Stock length 18mm
Charging: Type-C 20W Quick Charge
Battery: Built-in 4000mAh 1S2P 18650 Battery
Charging Connector: Type-C
Weight: 310g
ELRS Option Only (Single TX)
Single ELRS option includes 1x ELRS TX module (please select band) pre-installed in the back of the radio
A cooling fan is inside the flat back cover
Single Band or Dual Band antenna option (for future upgrades or module changes)
Dual Band antenna option for convenient multi-band use without changing the antenna
Button Functionality
2 x 5-Axis menu buttons for full OpenTX or EdgeTx control
2 x 2-position switches (not momentary)
2 x 3-position switches
Antenna Options
Single-Band (2.4GHz)
Band Options
The 900MHz as well as 2400MHz band have outstanding performance and long range capabilities. If you're not sure what to get, please checkout the official ELRS Long Range Competition to see what has been achieved.
What can I expect? Due to local regulations, the 915MHz FCC region seems to have a better performance than the 868MHz EU region. The 2400MHz band works great in any region, has a higher packet rate up to 500hz. This is not a common 2400MHz protocol and cannot be compared to anything prior on the market.
RF Power
868/915MHz system: SX1276
ExpressLRS 2.4GHz // Max Output 500mW
ExpressLRS 868/915MHz // Max Output 1000mW
BASE CC2500 2.4GHz Multiprotocol // Max Output 100mW
Radio Channels: 8
Input: Mini High Precision Digital Hall Gimbals with NMB bearings
Gimbal Stick Ends: Stock length 18mm
Charging: Type-C 20W Quick Charge
Battery: Built-in 4000mAh 1S2P 18650 Battery
Charging Connector: Type-C
Weight: 310g
Includes
1 x iFlight Commando 8 2.4GHz Radio Transmitter - ELRS
2 x 18650 Li-Ion batteries included (pre-installed)
The perfect upgrade part for your DJI Air Unit to avoid buying fragile stock antennas again and again...
Check out all our iFlight gear and our DJI FPV System Parts & Accessories!
Specifications
Frequency range: 5000-6000MHz
Gain: 3Dbi
Cable：RG141
Axial Ratio: 0.7
Interface: LHCP RP-SMA
Polarization: LHCP
SWR: ≤1.5 (ON 5.8GHz)
Weight: 4.2g/pc
Includes
2x iFlight Crystal HD 5.8GHz RP-SMA Stubby Antenna for DJI - LHCP
Let's welcome our new iFlight Crystal HD 5.8GHz Directional Antenna! Specially designed for the DJI Digital FPV Goggles to replace the stock front plate with our iFlight engineered Antenna Array. NO, this is not another patch antenna! Two carefully designed and highly sensitive LHCP high gain directional antennas give you a better reception at long range as well as better penetration through trees, bandos or other difficult terrains. Low profile design to decrease your pack size to a minimum, and high quality RG178 cables for best durability. We were able to achieve a super wide antenna beam width through an offset angle of 30 degrees between the two antennas. Horizontal beam of 105° and vertical beam of 75 degrees at 9dBi gain, dropping of slowly the further you get to the side! Low loss with a 93% antenna efficiency and a axial ratio of ≤1.6 through the whole band. If that's not enough, we also gave you the option to either mount your antennas at the bottom or top pair of the Goggle RP-SMA connectors. Multiple designs available, get them as long they last!
Check out all our iFlight gear and our DJI FPV System Parts & Accessories!
Features
3 designs available, Black Carbon, Blue Sticker Design, Red/Yellow Color Design.
LHCP high gain directional antenna array.
Lower profile and better reception than stock antennas.
Super wide beam width, horizontal 105° @9dBi, vertical 75° @9dBi.
Can be mounted on top or bottom Goggle RP-SMA pair.
Specifications
Frequency: 5.8GHz
Bandwidth: 5600~5900 Mhz
Gain: 9 dBi
Axial ratio: ≤1.6
Impendance: 50Ω
Radiation Efficiency: 93%
Beam Width: 105° H. 75° V.
Polarization: (LHCP) Left Hand Circularly Polarized
Cable: RG178
Connector: RP-SMA (Fits DJI Goggles directly, not to be used on standard SMA)
Dimensions: 16mm x 7mm x 3mm
Weight: 52.1g
Includes
1x iFlight Crystal HD Patch 5.8GHz RP-SMA Antenna for DJI - LHCP
2x iFlight Crystal HD Stubby 5.8GHz RP-SMA Antenna for DJI - LHCP
Props only work with the Defender 25 Motors
Replacement props, a set of four, for the Defender 25 Motors and Frame.
Check out our other 2.5" Props and our iFlight collection at RaceDayQuads!
Specifications
Model: Defender 2525
Propeller Diameter: 2.5inch
Pitch: 2.5 inches
Blade：3-Blade
Material: PC
Weight：1.1g
Hub Diameter: 9.6mm
Hub Thickness: 4mm
Shaft：1.9/1.5/1.9mm
Adaptor Rings: N/A
Includes
2x Defender 2525 (CW) Canis Mi25 2525-3
2x Defender 2525 (CCW) Canis Mi25 2525-3
All batteries must be shipped by a ground shipping method.This Battery only charges with the included Defender 25 Charger Adapter board.
Grab an additional battery or two for your iFlight Defender 25 and keep the fun going! With 6 minutes of flight time, you're sure to capture some amazing shots!
These batteries only work with the Defender 25 drone.
Specifications
Capacity: 550mAh
Cell Combination: 4S1P
Discharge rate: 60C
Weight: 70±2g
Size: 105x35x31.5mm±2mm
Battery type: LiPo
Connector: XT30
Cable Length: 32.5±1mm
Includes
1x iFlight Defender 25 4S 550mAh Battery
It's finally here, the iFlight ELRS 2.4GHz Receiver w/SMD Antenna! Extreme range and highest packet rate for lowest delay. Failsafes are a thing of the past! Developed in close cooperation with the ExpressLRS Team with firmware targets already released.
Note: This is now Plug & Play, coming with a short and long silicone plug harness.
Check out all our ExpressLRS compatible gear, and our entire iFlight selection!
Features
Improved circuit design
Market's lowest crystal frequency deviation (low packet loss, high frequency stability)
High-performance at 2400MHz or 900MHz (915 / 868 bands available)
Frequency tuned SMD antenna
Pre-soldered SH1.25 connector with 30mm wire length (Plug&Play for easy installation with iFlight FCs)
Specifications
Input Voltage: 5V
Firmware: ExpressLRS iFlight 2400RX
Frequency: 2.4GHz
Telemetry Power: 20dbm
Connector: SH1.25 including 30mm wire (pre-soldered)
Interface: 5V GND RX TX
Protocol: ELRS
Dimension: 12x19.5mm
Weight: 1.2g
Includes
iFlight ELRS 2.4GHz Receiver - Ceramic SMD Antenna
2 Plug & play silicone cables
An awesome little AIO from iFlight, Coming with 20A ESCs, DJI ready header for an air unit or Caddx Vista, and a nice open pad layout to get all your peripherals on board!
Browse our Stacks & Combos, and our iFlight gear!
Features
Support 2-4S battery, new upgraded UARTS ports
F411 chip is used with high-performance computing speed, making it smoother during flight.
Specifications
Whoop AIO F4 V1.1 AIO
Size：30.5x30.5mm
Mounting pattern：25.5x25.5mm/φ3mm
Weight: 7.5g
MCU：STM32F411
Gyro：BMI270
Blackbox：8MB
BEC output: 5V 2A
Config：IFLIGHT_F411_PRO.config
INA pad：nR2
Barometer：No
Constant current: 20
Burst Current: 25A
Input：2-4S
Current sensor：yes
BLHeli：BLHeli-S
ESC Telemetry：no
Firmware Target：IFLIGHT_F411_PRO
ESC Firmware: Bluejay Q-H-50
Includes
1x Whoop AIO F4 V1.1 AIO Board× 1
1x Capacitor UPL 35V 470UF × 1
1x XT30 18awg cable
1x Wire harness (plug&play) for DJI Air Unit × 1
4x M2 silicon grommets × 4
4x M2 damping balls x 4
4x M2x8mm Screws x 4
Spare replacement part for the iFlight iX3 frame.
Check out all our iX3 spares as well as our iFlight gear selection!
Includes
2x iFlight iX3 Lite V3 Camera Plate
Easy to use, nicer looking, and perfect for protecting wires.
Choose the right size for your build!Check out our hardware selection, all our pigtails, connectors and adapters as well as our iFlight selection!
Specifications
Width: 5mm or 10mm (optional)
Length: 24.5mm, 26mm,40mm, 43mm, 50mm, 65mm (optional)
Color: Grey
Application: for Motor, 4 in 1 ESC etc.
Includes
4x Motor Wire Shield
Say goodbye to dirt and grass clogging up your electronics after a crash! This latest frame ensures your flight controller and ESCs stay clean, avoiding any potential failure or shorts. Plus, it's lightweight and with strategic airflow to keep your components cool. The illuminated side panels and 360-degree TPU parts will keep you protected too. Plus, the Deadcat design eliminates props in your footage for pro-grade cinematic shots. With the upgrade of the V2 comes the support for the DJI O3 Air Unit for this frame.
Check out our iFlight selection, as well as all our other 5" frames,
Features
V1 to V2 was upgraded for the DJI O3 HD Air Unit Digital Transmission
Specially Designed Heatsink for DJI O3 Air Unit
New Camera Mount for a wider camera FOV with TPU damping inserts
New Side Panels to perfectly fit the O3 Air Unit in the back
New Dual 5.8G VTX Antenna TPU mount
Latest Nazgul Frame Upgrades for Maximum Protection
Optional Parts to select (not included in frame kit):
New Anti Spark Filter to prevent rapid voltage and current spikes plugging in a battery
Single DJI VTX Antenna TPU to install the original DJI O3 set included antenna.
Specifications
Product Name: Evoque F5 V2 Frame Kit - DeadCat
Frame wheelbase: 223 mm (DeadCat)
Frame Dimension: L190xW136xH36 mm (DeadCat)
Frame Body Dimension: 36mm
Arm Thickness: 6mm
Bottom Plate Thickness: 3mm
Top Plate Thickness: 2mm
Upper Plate Thickness: 3mm
Camera Plate Thickness: 3mm
Max Flight Stack Height: 22mm
Max VTX Height: 23mm
Motor Mounting: 16x16mm
VTX Mounting: 25.5x25.5/Φ1.6mm
Weight: 240grams
Includes
1x iFlight Nazgul Evoque F5D V2 HD O3 Deadcat 5" Freestyle Frame Kit w/ LED Side Plates
1 x O3 Air Unit Heatsink
2 x O3 IPEX to RP-SMA Antenna Pigtails
1 x O3 Dual Antenna TPU
1 x GoPro TPU Base Mount
1 x Screw Bag
4 x TPU Armguard
1 x Front Bumper TPU
1 x Rear Bumper TPU
2 x Anti-slip Battery Pad
2 x Battery Strap (20x250mm)
Say goodbye to dirt and grass clogging up your electronics after a crash! This latest frame ensures your flight controller and ESCs stay clean, avoiding any potential failure or shorts. Plus, it's lightweight and with strategic airflow to keep your components cool. The illuminated side panels and 360-degree TPU parts will keep you protected too. With the upgrade of the V2 comes the support for the DJI O3 Air Unit for this frame.
Check out our iFlight selection, as well as all our other 5" frames,
Features
V1 to V2 was upgraded for the DJI O3 HD Air Unit Digital Transmission
Specially Designed Heatsink for DJI O3 Air Unit
New Camera Mount for a wider camera FOV with TPU damping inserts
New Side Panels to perfectly fit the O3 Air Unit in the back
New Dual 5.8G VTX Antenna TPU mount
Latest Nazgul Frame Upgrades for Maximum Protection
Optional Parts to select (not included in frame kit):
New Anti Spark Filter to prevent rapid voltage and current spikes plugging in a battery
Single DJI VTX Antenna TPU to install the original DJI O3 set included antenna.
Specifications
Product Name: Evoque F5 V2 Frame Kit - Squashed X
Frame wheelbase: 225mm (Squashed X)
Frame Dimension: L258xW199xH25 mm (Squashed X)
Frame Body Dimension: 36mm
Arm Thickness: 6mm
Bottom Plate Thickness: 3mm
Top Plate Thickness: 2mm
Upper Plate Thickness: 3mm
Camera Plate Thickness: 3mm
Max Flight Stack Height: 22mm
Max VTX Height: 23mm
Motor Mounting: 16x16mm
Electronic Mounting: 20x20mm
VTX Mounting: 25.5x25.5/Φ1.6mm
Weight: 240grams
Includes
1x iFlight Nazgul Evoque F5X V2 HD O3 5" Freestyle Frame Kit w/ LED Side Plates
1 x O3 Air Unit Heatsink
2 x O3 IPEX to RP-SMA Antenna Pigtails
1 x O3 Dual Antenna TPU
1 x GoPro TPU Base Mount
1 x Screw Bag
4 x TPU Armguard
1 x Front Bumper TPU
1 x Rear Bumper TPU
2 x Anti-slip Battery Pad
2 x Battery Strap (20x250mm)
iFlight's ever-popular Nazgul props just got a new version. The Nazgul F5 props are less aggressive, but still just as durable.
Check out the rest of our 5" props, and all our iFlight selection!
Specifications
Diameter: 5"
Pitch: 3.5"
Blades: 3
Material: Polycarbonate
Hub Thickness: 6.3mm
Shaft Hole: 5mm
Weight: 3.9g
Includes
4x iFlight Nazgul F5 Tri-Blade 5" Props
Replacement front arm for the iFlight Nazgul Evoque F5D V2 HD O3 Deadcat 5" Freestyle Frame Kit w/ LED Side Plates.
Check out all of our iFlight Frames & accessories and our selection of iFlight gear!
Choose between arm R or L, depending on which arm you need!
Specifications
Arm Thickness: 6mm
Includes
1x iFlight Nazgul F5D V2 5" Replacement Front Arm (1pc) - Choose Your Version
Replacement rear arm for the iFlight Nazgul Evoque F5D V2 HD O3 Deadcat 5" Freestyle Frame Kit w/ LED Side Plates.
Check out all of our iFlight Frames & accessories and our selection of iFlight gear!
Choose between arm R or L, depending on which arm you need!
Specifications
Arm Thickness: 6mm
Includes
1x iFlight Nazgul F5D V2 5" Replacement Rear Arm (1pc) - Choose Your Version
Replacement arm for the iFlight Nazgul Evoque F5X V2 HD O3 5" Freestyle Frame Kit w/ LED Side Plates.
Choose between arm A or B, depending on which arm you need!
Check out all of our iFlight Frames & accessories and our selection of iFlight gear!
Specifications
Arm Thickness: 6mm
Includes
1x iFlight Nazgul F5X V2 5" Replacement Arm (1pc) - Choose Your Version
These are replacement arms for the Nazgul XL5 frame.
Check out our other XL5 accessories, as well as the rest of our iFlight selection!
Includes
2x iFlight Nazgul XL5 Replacement Arm
Power your GoPro with your craft's LiPo, with this Type C to Balance Head Charging Cable for GoPro Hero 6/7/8!
Check out the Rest of our iFlight product range and PDB/BEC selection while you're at it!
Features
High Comparability: Compatible with GoPro Hero 6/7/8
High quality and fast charging.
Specifications
Model: Type-C 90 degree to balance plug
Product Weight: 5.5g
Support: 4S-6S
Output: 5V/3A
Input Connector: XH2.54
Output connector: 90°Type-C
Length: 110mm
Includes
1x Type C to Balance head Charging Cable
This multipurpose 4-in-1 prop tool by iFlight comes with a one way bearing 5mm prop nut driver and M1.5/M2 hex drivers to help with your fpv needs!
Check out our other prop tools, nuts, and accessories, as well as the tools and building supplies section!
Includes
1x iFlight Quad Wrench
This motor has been specially developed for Race drones, such as the Mach R5 Racing drone. Thanks to advanced construction in the manufactory, its smooth, reliable and powerful performance is improved yet again. By introducing new center-slotted N52H curved arc magnets, the motor's response time is drastically shortened. As a result of the high quality materials used and the durable joint of bell and shaft, we were able to reduce the magnet air gap and stator lamination to a minimum. The smaller the air gap is, the lower that reluctance and the higher the magnetic flux (which is the magnetic analog of current), causing more efficiency and higher power!
iFlight is one of the most respected companies in the FPV community when it comes to premium motors; this is one of them.
Check out our iFlight selection and our entire selection of motors!
Specifications
Model: R5 2207 Motor
KV: 2050KV
Weight(included wire): 34.6g
Dimension: 28.x31.5mm
Interphase Resistance: 56.3mΩ
Input Volts: 25.2V
Peak Current: 49.53A
Max Watt: 1166.4W
Mounting Holes: 16x16 φ3mm
Shaft Diameter: 5mm
Shaft Protruding Length: 12.5mm
Lead: 150mm/20AWG
Magnet: N52H Curved
Configuration: 12N14P
Bearing Type: NSK
Bearing Specification: φ9xφ4x4
Winding: Single Strand copper winding
Includes
1x iFlight R5 2207 2050Kv Motor
4x M3x8
1x M5 Flanged Nylon Insert Lock Nut
Spare replacement cable for use between Succex-D F7 or Succex-D F7 Mini and DJI Air Unit.
Check out the rest of our DJI compatible gear section and all our iFlight products!
Specifications
Length: 90mm (with plugs)
wire length: 80mm
Double-ended 1.25-1.0mm terminal line
Includes
1x iFlight Succex-D to DJI Air Unit Cable
Type C 90° connector for the DJI FPV system.
Check out our DJI compatible quads and accessories, and all our iFlight gear!
Specifications
1x iFlight USB C 90° Adapter for DJI Air Unit
A relatively large motor for a 12x12mm, M2 mounting pattern. This motor is ideal for lightweight 5" builds.
Check out all our Micro Motors and our selection of iFlight gear!
Features
High-strength 5mm Steel shaft
Japanese NSK φ8*φ3*4 bearings
N52H curved magnets
Motor wires protected
Dynamically balanced
Specifications
KV: 2300KV
Input Voltage: 4S/6S Lipo
Configuration: 12N14P
Stator Diameter: 22mm
Stator Length: 5mm
Bottom Mounting pattern: 12*12mm/M2
Weight: 25.5g with short wire
Includes
1x iFlight Xing 2205 2300Kv Micro Motor
iFlight continues their tradition of producing excellent motors in a variety of sizes and Kv to meet the needs of different build types and flight styles with the iFlight Xing 2306 1700Kv Unibell Motor. They're not just some of the best-looking motors around. A high-strength titanium alloy shaft, quality bearings and N52H magnets, and precision machined bell and base are just a few features of the Xing series.
Now featuring a new "unibell" solid 1 piece bell design!
Check out the rest of the specs below, and be sure to browse the rest of our iFlight products and vast motor selection.
Features
Elliptical Body, High-strength Titanium Alloy Shaft
Large Heat Dissipation Hole Design (15℃ cooler than same range motor)
Crush resistant damping bearing eliminates vibration effectively
50%-80% optimal throttle output for best efficiency
160mm cable length for different frames and setups
CNC high precision machined 7075 aluminum bell and base
220℃ Pacific heat resistant copper wire, solid wire windings
Electromagnetically matched magnets and stator
Japanese Kawasaki 1200 iron core
N52H high temperature magnets
Motor wire protected
Hex bolt shaft set screw
Dynamically balanced
Specifications
Kv: 1700
Input Voltage: 3-6S
Configuration: 12N14P
Max Continuous Current: 37.2A
Internal Resistance: 76.4mΩ
ldle Current@10v: <1A
Motor Dimensions: Φ29.5×18.7mm
Stator Dimensions: Φ23×6mm
Prop Shaft Dimensions: M5x13.5mm
Shaft Diameter: 4mm
Wire Dimensions: 20AWG×160mm
Mounting Pattern: Φ16mm, 4×M3
Weight (w/ wires): 33.1g
Includes
1x iFlight Xing 2306 1700Kv Unibell Motor
1x Hardware Set
iFlight XING provides the most incredible power and thrust in the lightest weight. iFlight continues the tradition of making the best and most suitable products to offer different size and KV value to meet different pilots’ needs. It means that the iFlight XING series motor can be pushed to the limit. The sturdy structure and high-quality materials make iFlight XING perform like a beast.
Check out our other 2306 motors, and all our iFlight selection!
Specifications
Kv: 2450Kv
Input Voltage: 2-4S LiPo
Configuration: 12N14P
Max Continuous Current: 44.57A
Internal Resistance: 47.3mΩ
Motor Dimensions: Φ13.5mm x 18.7mm
Stator Dimensions: Φ23mm x 06mm
Shaft Diameter: 5mm
Mounting Pattern: Φ16mm
Weight: 33.4g
Includes
1x iFlight Xing 2306 2450Kv Motor
The Motor Xing 2806.5 designed for bigger quads like 7-8 inch quad frames, which is with better efficiency in this range frames. The Xing 2806.5 features uni-bell design and adopt Japan NSK bearing, N52H arc magnets. It offers incredible thrust number, highly responsive and extremely smooth flight characteristics. The bigger stator size 2806.5 allows it to provide instant power to save you from those crazy mountain dives last minute. It's a great motor if you're building bigger drones like 7 inch or 8 inch.
Check out all our motors, and our iFlight gear selection!
Features
High-strength 4mm Titanium alloy shaft
Unibell design
7075 aluminum Bell and Base
Electromagnetically matched magnets and stator
Japanese NSK 11x5x5 bearings
N52H Arc curve magnets
Motor wires protected
Hex bolt shaft set screw
Dynamically balanced
Specifications
Voltage: 2-6S
KV Option: 1800
Configuration: 12N14P
Bearing: NSK 11x5x5mm
Stator Diameter: 28mm
Stator Length: 6.5mm
Shaft Diameter: M5
No.of Cells(Lipo): 2-6S
Motor mount hole: 19x19mm, M3
Weight: 49.5g(with a short cable)
Includes
1x iFlight Xing 2806.5 1800Kv Unibell Motor
1x M5 Nut
4x M3x8 Screw
