Due to the poor filtering effect of the video antenna input and the wide operating frequency of the most common 1.2-1.3GHz video receivers. They are unable to properly separate video transmission from 868MHz/915MHz transmission signals leading to interference, and this is where the Flywoo notch filter comes in tackling that interference. This is used on video links to avoid interference from a 900MHz control link.
Check out our FPV Wing Gear, as well as the rest of our Flywoo selection!
Specifications
Small size, lightweight, low loss, imported components, and SMA universal connector.
A notch filter suitable for 1.2-1.3GHz video transmission, effectively blocking 868MHz/915MHz signals to prevent interference from remote control transmission signals in video transmission and image quality.
Install this notch filter between the video receiver and the antenna, connected through an SMA connector.
Weight: 5.2g
Includes
1x Flywoo 1.2/1.3GHz VRX Notch Filter 900Mhz - (2pc)
These 1.2GHz-1.3GHz SMA dipole antennas (2pc) offer reliable and durable performance, providing high-quality linear reception that ensures consistent signals and faster speeds.
Check out our ever-expanding selection of VTX antennas as well as the rest of our Flywoo selection and our FPV Wing Gear!
Specifications
Type: Dipole
Bandwidth: 1.2-1.3Ghz
Center freq 1240MHz
Connector: SMA
Weight: 7g
Length: ~14.4cm
Width: ~8.7cm
Includes
1x Flywoo 1.2GHz-1.3GHz SMA Dipole Antenna (2pc) - Linear
All batteries must be shipped by a ground shipping method.
Explorer Lionpack 3000mAh is the highest quality battery customized for Explorer LR. The weight is only 197.7g. Explorer LR 4inch can get more than 37 minutes of flight time with this pack.
Check out the rest of our Flywoo products and our whole battery collection!
Features
Original brand-new SONY VTC6 18650 high quality cells.
Very suitable for long range flight, discharge current 30A.
Explorer LionPack batteries will never puff and become unsafe like a Li-Po.
Explorer LionPack batteries can be charged from empty or nearly full without damaging the pack.
Explorer LionPack batteries can be charged over 350 times and still store 85% of its original capacity.
High quality fireproof heat shrinks outer skin.
Compact size. Light weight.
Ideal power solution for all RC hobby products, including RC cars, boats,etc…
Specifications
Battery Brand: SONY VTC6 18650
Max. Charge Current: 5A
Max. Charge Voltage: 4.2V per cell
Max. Continuous Discharge Current: 30A
Power Lead: XT30
Balance Lead: XH2.54
Capacity: 3000mAh
Nominal Voltage: 14.8V
Size: 68x37x37mm
Weight: 198g
Includes
1x Flywoo 14.8V 4S 18650 3000mAh 30C Li-Ion Battery - XT30
FLYWOOs newest strap offering is a perfect balance of light weight, functionality and durability. Instead of stitching a rubber sheet to the strap, rubber is woven into the kevlar of the strap itself making it lighter and thinner overall while maintaining a strong grip on your LiPos. Featuring a welded steel buckle on one end and an embroidered FLYWOO logo on the other.
Check out the rest of our battery straps & pads and our Flywoo gear selection!
Specifications
Length: 200mm
Width: 2cm
Includes
2x Flywoo 200mm Kevlar Battery Strap
FLYWOOs newest strap offering is a perfect balance of light weight, functionality and durability. Instead of stitching a rubber sheet to the strap, rubber is woven into the kevlar of the strap itself making it lighter and thinner overall while maintaining a strong grip on your LiPos. Featuring a welded steel buckle on one end and an embroidered FLYWOO logo on the other.
Check out the rest of our battery straps & pads and our Flywoo gear selection!
Specifications
Length: 250mm
Width: 2cm
Includes
2x Flywoo 250mm Kevlar Battery Strap
Designed for the Flywoo Chasers \ Vampire-2, but can be used anywhere a micro USB is needed! Easily access limited spaces with a set of two 90° Micro USB Adapters, perfect for those tight places in your FC/ESC stacks.
Check out our Flywoo selection.
Includes
1x Flywoo 90° Micro Male to Micro Female USB Adapter Board
Flywoo A30 Connectors provide a strong and reliable connection up to 15A of continuous current. This set includes 5 MALE and 5 FEMALE connectors, ideal for high current applications. Make sure your connection is secure with the Flywoo A30 Connectors.
Check out all our pigtails and connectors as well as our products from Flywoo!
Specifications
Model: A30
Plug color: Black
Peak Discharge Rate: 30A
Standard Current: 15A
Contact Impedance 1.6mO
Withstand voltage: DC 500V
Flame Retardant rating: UL94 VO
Metallic Material: Brass gliding
Insulating material: Brass gliding
Wire: 20#/22#
Operating temperature: -20 to 120 °C
Applications: Chargers/Battery
Includes
1x Flywoo A30 Connector Male/Female Set (5x Male Connectors/ 5x Female Connectors)
Flywoo's custom new antenna specifically designed for the Flywoo Firefly 2S, Not saying that it couldn't be used in your next sweet custom build!
Check out our ever expanding selection of VTX antennas and our Flywoo gear selection!
Specifications
Frequency range: 5500-6000MHz
Gain: 3dbi
Axial Ratio: 0.7
Cable： RG1.37
Length: 30mm
Polarization: LHCP
SWR: ≤1.5 (ON 5.8GHz)
Includes
1x Flywoo Atomic 5.8GHz U.FL Antenna - LHCP 40mm / 10mm Tube
From the creator of the classic dead cat design for micro long-range, Dave_C FPV. As well as the collaboration with Flywoo, we at RaceDayQuads present you the Flywoo Explorer LR HD. Small, long-range, lightweight, and a DJI O3 FPV Air Unit, now that is a recipe for fun. This quad features the GOKU Versatile F405 Pro Mini Stack, NIN 1404 V2 2750KV Motors, and V3.0 GPS.
Want a guide for this drone, well here you go: Drone Guide
Check out our other DJI O3 Compatible Quads, and also see our other great products from Flywoo!
Features
Long-range capabilities up to 10KM (FCC)
Newest GOKU MINI GPS V3 for Explorer O3
GPS search up to 30 satellites
Plug&Play plug O3 Air unit. Hence there is no need to solder
4K/60fps recording for high-quality footage
Latest GOKU MINI GPS V3 for greater accuracy
Compact and lightweight design, weighing less than 250g even with the battery
Long flight time of up to 30 minutes
User-friendly controls for easy operation
DJI O3 FPV AIR UNITThe DJI O3 Air Unit integrates DJI's cutting-edge video transmission technology into a lightweight and compact body, the DJI O3 Air Unit features state-of-the-art DJI transmission technology enclosed in a lightweight, compact design. See for yourself that it's possible! The DJI O3 Air Unit will provide you with excellent image quality over long distances and is distinguished by ultra-low latency, thanks to which you will take your FPV experience to a whole new level. The device is a real breakthrough in imaging performance - it offers a 1/1.7-inch sensor, flagship video technology, 155° super-wide field of view, and more. It is also distinguished by its compatibility with a wide range of products. Get a reliable image transmission tool, unleash your creativity and enjoy even more sky-high travels!GOKU GM10 MINI GPS V3.0The V3.0 GPS allows for up to 30 satellites to be searched, making the rescue function more reliable. Safeguard your cruise flight with a built-in buzzer and up to 5 hours of standby.PRE-TUNED AND PRE-SETUPThis RTF is fully built and test-flown by build technicians at Flywoo.
Specifications
FC and ESC : Goku Versatile F405 Pro Mini Stack - F405 FC + 40A ESC
Frame: Explorer LR 4 03 (Different from OG Explorer LR frame)
Model: Explorer LR 4 HD DJI 03
Propellers: Gemfan 4024 2-Blade
Motors: NIN 1404 V2 2750Kv
Antenna: DJI 03 antenna
VTX: DJI 03 Air Unit
Wheelbase: 168mm
Camera: DJI 03
Brand: FLYWOO
Weight: 168.4g
GOKU GN F405 Pro Mini 40A 20x20 Stack
GOKU Versatile F405 PRO FC
Input Voltage: 2-6S Lipo
MCU: STM32F405BGA
GYRO: ICM42688P
UARTS: 1/2/3/4/5/6
I2C: SCL/SDA
Barometer: BMP280
BEC: 5V 2A / 10V 2A
Blackbox: 16M
Input Voltage: 2-6S
Firmware: FLYWOOF405PRO
Mounting: 20x20mm M3 / 30x30mm M4
ESC Soft: Dshot300/600
ESC Telemetry: Yes
LED Controller: BF LED
F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 2~6S Lipo (8.4~25.2V)
TVS Protection: Yes
GOKU 406S 8bit 40A ESC
Con. Current: 40A
Burst Current: 45A
Input Voltage: 2-6S
Support DShot300/600
Current Sensor: YES
BEC Output: NO
Size: 42×42×4mm
Mounting Hole: 20x20mm ( M3)
FPV System
VTX: DJI O3 Air Unit (Requires DJI Goggles 2 or DJI FPV Goggles V2)
Channels: : Auto mode support Manual mode support: 40 MHz: 1 channel; 20MHz: 3 channels; 10MHz: 3channels
Camera: DJI O3 Air Unit Camera
VTX Antenna: DJI O3 Air Unit Antenna
Includes
1x Flywoo BNF Explorer LR 4" Deadcat HD 4S Quad w/ DJI O3 Air Unit - ELRS
2x Gemfan 4024-2 Black Propellers (Set of 4)
2x Battery Strap 15x180mm
1x Hardware Set
This Flywoo BNF Explorer LR 4" HD 4S Quad comes with Walksnail Avatar V2 & Avatar Micro Cam V2, giving you buttery smooth and stabilized video performance. The advanced quadcopter technology lets you take your FPV adventures to new heights! Choose your receiver between ELRS 2.4GHz and TBS CRSF 915 Mhz for a secure flight. Enjoy the unparalleled performance and take your FPV adventures to new heights with this cutting-edge technology! This long range quad is a small efficient cruiser with a deadcat design eliminating props in your view, perfect for the elite capabilities of the Walksnail system.
Be sure to check out our Bind-n-Fly collection and our Walksnail Compatible Quads and Electronics as well as other great products from Flywoo!
Features
Compact and lightweight design, weighing less than 250g even with the battery
Long flight time of up to 30 minutes
User-friendly controls for easy operation
Support 1080P 120fps Recording
Latency Average Delay 22ms
Walksnail Avatar V2 Kit 8G ( Camera & VTX)
Walksnail WS-M181 GPS: Featuring the u-blox M10 platform UBX-M10050 GNSS chipset and BUILT-IN QMC5883 MAG, the module offers stronger performance and more accurate positioning.
Specification
Model: Explorer LR 4 HD Walksnail Sub250 Micro Long Range
Brand: FLYWOO
Frame: Explorer LR 4 HD Walksnail Frame kit
FC and ESC: Goku Versatile F405 Pro Mini Stack ( F405 FC+ 40A ESC )
VTX & Cam: Walksnail Avatar HD Kit V2 (8G)
Propeller: Gemfan Hurricane 4024 2
Antenna: Flywoo Circular Polarized 5.8GHz UFL Antenna - LHCP
Motor: NIN 1404 V2 ULTRALIGHT FPV MOTOR
Weight: 168.4g
Flight Controller Specifications
MCU: STM32F405BGA
GYRO: ICM42688P
UARTS: 1/2/3/4/5/6
I2C: SCL/SDA
Barometer: BMP280
BEC: 5V 2A / 10V 2A
Blackbox: 16M
Input Voltage: 2-6S
Firmware: FLYWOOF405PRO
Mounting: 20x20mm M3 / 30x30mm M4
ESC Soft: Dshot300/600
ESC Telemetry: Yes
LED Controller: BF LED
F.Port: Yes
RSSI: Yes
Buzz: Yes
Input: 2~6S Lipo (8.4~25.2V)
TVS Protection: Yes
ESC Specifications
Con. Current: 40A
Burst Current: 45A
Input Voltage: 2-6S
Support: DShot300/600
Current Sensor: YES
BEC Output: NO
Size: 42x42x4mm
Mounting Hole: 20x20mm ( M3)
Motor Specifications
Kv: 2750Kv
Input Voltage: 4-6S
Stator diameter: 14mm
Stator height: 4mm
Bearings: NSK
Wire Length: 24AWG 150mm
Shaft size: 1.5mm
Mounting Screw Pattern: 12x12 mm
Weight: 8.7g
VTX Specifications
Communication Frequency: 5.725-5.850GHz
Transmitter Power(EIRP): FCC<30dBm;CE:<14dBm;SRRC:<20dBm;
MIC:<25dBm
1/O Interface: JST1.0x4(Power in)JST0.8x6(USB)
Mounting Holes: 25.5x25.5mm; 20x20mm
Dimensions: 33.5x33.5x10.5mm
Storage: 8G
Recording: 1080p/720p
Weight: 17.6g
Operating Temperature: -20-40℃
Channels: 8
Wide Power Input: 6V-25.2V
Supported FC System: Betaflight; Inav; Fettec; ArduPilot; Kiss
OSD: Canvas mode
Latency Average delay: 22ms
Antenna Connector: U.FL
Camera Specifications
Model Avatar: V2 camera
Image Sensor: 1/3.2-Inch 4Mp 4:3sensor
Resolution: 1080P/60fps; 720P/100fps; 720P/60fps;1080P/120fps compatibility; 1080P/100fps compatibility
Ratio: 4:3 native /16:9
Lens: 2.1mm
FOV: 160°
Aperture: F2.0
Shutter: Rolling shutter
Min.Illumination: 0.001Lux
Weight: 7.2g
Dimensions: 19x19x22mm
Coaxial Cable: 140mm
Prop Specifications
Diameter: 4"
Pitch: 2.4"
Blades: 2
Material: Polycarbonate
Disk Diameter: 102.33mm
Max Prop Width: 13.38mm
Hub Thickness: 5.5mm
Shaft Hole: 1.5mm
Weight: 1.61g
Antenna Specifications
Gain: 2.2dBi
Axial ratio: 1.0 Around
Band Width: 5.6Ghz – 6.2GHz
Axial Ratio: Around 1.0
Polarization: LHCP
Connector: UFL
Weight: 1.6g
Include
1x Flywoo BNF Explorer LR 4" Deadcat HD 4S Quad w/ Walksnail Avatar V2 & Avatar Micro Cam V2 - Choose Your Receiver
1x Hardware Kit
8x Gemfan 4024-Bi Blade Balck
2x Battery strap 15x180mm
1x Set of screws
The Flywoo Firefly Nano Baby 20 2S Micro Quadcopter BNF Analog comes with Flywoo's Nano Camera V2 and is equipped with the most efficient micromotor and the top AIO flight controller on the market! This micro quadcopter will bring you an unprecedented flying experience; the Firefly Nano Baby 20 can do crazy acro and keep up with all the tricks up your sleeve.
Check out the rest of our pre-built quads, as well as the rest of our Flywoo selection!
Features
Comes with 1002 15500KV motors and Gemfan 2015 - 2 blade propellers, which provide the best balance of performance and flight time.
Versatile and highly integrated circuit board - GOKU Versatile F405 2S 12A AIO. Built-in ELRS 2.4g RX. Have multiple sets of serial external devices.
Easy switch battery mount design. Explorer 2S 420mAh for Racing, Explorer 2S 750mAh for long flight time.
Great mount compatibility for cameras like the Thumb Pro, Peanut, GO2, Thumb, and related
Specifications
Weight: 33.8g (without battery)
FC & ESC: GOKU Versatile F405 2S 12A AIO
Frame: Firefly 2S Nano Baby 20 Analog Frame kit
Motors: Flywoo ROBO 1002 15500KV
Props: Gemfan 2015-2 blade
VTX: GOKU VTX625 V2 450mW Nano VTX
Camera: Flywoo 1.2g 1S Nano camera V2
GOKU Versatile F4 5-IN-1 1S AIO FC
Size: 30x30mm
Weight: 4.1g
Hole: 25.5x25.5-3mm
MCU: STM32F405
UARTS: 1,2,3,4,5,6
MOTOR: M1-M4 OUTPUT I2C: SCL/SDA
GYRO: ICM42688
Barometer: BMP280
LED: 2x WS2812
Flash: 8M
BEC: 5V 2A
Firmware: FLYWOOF405S_AIO
Onboard 4in1 ESC
Built-in 1S/2S 12A BL_S 4in1 ESC
Support Oneshot125, Oneshot42, Multishot,
Dshot150, Dshot300, Dshot600
Input Voltage: 1-2S Lipo
Firmware: BLHELI_S
Firmware: Z_H_30_REV16.7
Flywoo ROBO 1002 15500Kv Motor
Kv: 15500Kv
Input Voltage: 2S LiPo
Stator Dimensions: Φ10mmx2mm
Shaft Diameter: Φ 1.5mm
Wire Dimensions: 30AWGx40mm
Weight (w/ wires): 2.4g
Flywoo 1S Nano Camera V2
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC and PAL(switchable)
MENU: Support
IMAGE: 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio: >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm/F2.5
Min. illumination: 0.001Lux
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14x14mm
Wide Power Input: DC 5-25V
Work Temperature: -20°C~+60C
Work Humidity: 20%~80%
Weight: 1.2g (N.W.)
Includes
1 x Flywoo BNF Firefly 2S Nano Baby 20 2" Quad Analog w/ GOKU VTX625 V2 & Nano Camera V2 - ELRS 2.4GHz
2 x Sets of 2015-2 props
1 x Screw spare packs
2 x Battery holder
4 x Prop guards
In an effort to push the boundaries of carrying the camera on the smallest platform, Flywoo designed the smallest quadcopter possible in their history. The Firefly Baby Quad is a nano-sized FPV drone designed to carry an Insta360 Go, or SMO 4K cameras for some action flying. Weighing in at just 47g, the Firefly Baby Quad is small, flexible, and stable. It's full of power and offers unmatched control. Pilots can quietly enjoy the fun of shooting a video without jello. Perfect for the indoor and outdoor recording of every beautiful flying moment!
Check out our other pre-built quads, as well as other great products from Flywoo!
Specifications
Weight: 47g
Wheelbase: 80mm
FC & ESC : GOKU GN405 Nano 13A STACK ( 16x16 )
Frame: Firefly Baby Quad Frame (Analog Verison)
Motors: Nin V2 1203Pro 5500KV
Props: Gemfan 1636 40mm-4 V2.0
VTX: Goku VTX625 450mw
Antenna: Atomic 5.8GHz Antenna Length 30mm (RHCP)
Battery: 4S 450mAh / 4S 300mAh battery (Not including)
Flywoo GOKU GN405 NanoFlight Controller
MCU: STM32F405 BGA
IMU: ICM42688
UARTS: 6
Soft Serial Ports: 2
I2C: Yes
Onboard LED：WS2812x8(FCx4/ESCx4)
Supports: SBUS, iBus, Spektrum, Crossfire
BlackBox: 16Mb Flash
BEC: 5V Power Out: 2.0A max, 3.3V Power Out: 0.5A max
Dimensions: 22x22mm
Mounting Holes: 16x16mm
Weight: 2.3g
Flywoo GOKU BS13A 4in1 ESC
Support: Oneshot, Multishot, Dshot150, Dshot300, Dshot600
Input Voltage: 2-4S Lipo
Continuous Current: 13A
Firmware: BLHELI_S
Mounting Pattern: 16x16mm, M3 Hole
Weight: 2.5g
Nin V2 Motor
Stator Size: 1203
KV: 5500
Goku VTX625 450mw
Raceband: 5362-5945 MHZ
Power: PIT/25/50/100/200/450mW switchable
Input Voltage: 5V
Control Mode: IRC Tramp(RX) & Button
Video System: NTSC/PAL
Antenna: IPEX (U.FL)
Size: 30mmx30mmx4mm
Weight: 1.3g
Includes
1x Flywoo BNF Firefly Baby V1.3 4S 1.6" Analog Micro Quad - Choose Receiver
Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the great capabilities of HDzero System.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Dead Cat Style
The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers.
New Design
Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Efficient Power Combo
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
Ultra-light AIO with ELRS 2.4G RXThe drone's GOKU Versatile F411 VTX 1S AIO V2 includes a built-in 250mW video transmitter, enabling an extended flight range and ultimate lightweight design without sacrificing performance, with improved circuit board stability.
HD Digital VTX System
The HDZero Nano Lite Camera is a revolutionary product designed for lightweight drones, weighing only 1.5g and combined with the new Whoop Lite VTX at 4.5g. Supporting 1-3S power input, it can record in 720P/60FPS with ultra-low latency of less than 19ms and features OSD function configuration through Betaflight Configurator.
More Power, More Flight Time
The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed.
Specifications
Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit
Motor: ROBO 1002 19800KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Propeller: 1608-3 Blade 40mm 1.5mm Shaft
Camera: Nano Lite Cam
Weight: 31g
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
ROBO 1002 19800KV
Configuration: 9N12P
Stator Diamter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.3
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 44
Internal Resistance: 89mΩ
Max Current(3S): 11.8A
Max Efficiency Current: (2-4A)>84%
HDZERO WHOOP LITE VTX
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Resolution: 1280x720@60fps
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Weight: 7g total package
HDZERO NANO LITE CAMERA
Size: 14x16x11mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor
FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65°
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz
4x 1608 -3 40mm 1.5mm shaft
2x TPU battery mount
1x hardware screws set
4x Prop guards
Experience superior performance with the Flywoo BNF Firefly DC16 Nano Baby V2.0 1S Deadcat Analog Micro Quad. Boasting a 30% power increase compared to its predecessor, it offers extended flight time while providing an incredibly stable flight experience. It comes with a new and improved canopy design for increased camera protection and a crash-resistant bottom plate for added durability. Enjoy the unmatched experience of this incredibly crafted drone from Flywoo. Experience the elite capabilities of HD Walksnail System.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Dead Cat Style
The drone boasts a dead cat design that enhances stability, extends battery life and provides an unobstructed flying experience with hidden propellers.
New Design
Redesigned canopy with enhanced aesthetics and reinforced camera protection.Bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Efficient Power Combo
Equipped with ROBO 1002 19800KV motor and 1608 3-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
Ultra-light AIO with ELRS 2.4G RX
The drone's GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance. This allows for the ultimate lightweight design without sacrificing functionality.
HD Digital VTX System
The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting.
More Power, More Flight Time
The A30 plug can sustain a continuous current of 15A, whereas the PH2.0 connector can only support 4.5A. Given the same capacity, the A30 plug can release more current, providing greater power and, as a result, longer flight times even when flying at full speed.
Specifications
Frame Kit: Firefly 1S DC16 Nano baby quad Frame kit
Motor: ROBO 1002 19800KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Propeller: 1608-3 Blade 40mm 1.5mm Shaft
Camera: Avatar Lite Cam
Weight: 33g
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
ROBO 1002 19800KV
Configuration: 9N12P
Stator Diamter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.3
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 44
Internal Resistance: 89mΩ
Max Current(3S): 11.8A
Max Efficiency Current: (2-4A)>84%
Walksnail Avatar HD Mini 1S Lite
Model: Avatar mini 1s module
Communication Frequency: 5.725-5.850GHz
Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm;
MIC:<25dBm
I/O Interface: JST1.0x6(Power in)JST1.0x4(USB)
Mounting Holes: 25.5x25.5mm
Dimensions: 30x30x6.5mm
Storage: 8G
Recording: 1080p/720p
Weight: 5.1g
Operating Temperature: -20-40℃
Channels: 8
Wide Power Input: 3.1V-5V
Supported FC System: Betaflight
OSD: Canvas mode
Bitrate: 25mbps, 50mbps
Latency Average delay: 22ms
Antenna: IPEX
Avatar lite camera
Model: Avatar lite camera
Image Sensor: 1/2.7”1nch
Resolution: 1080P/60fps,720P/120fps,720P/60fps
Ratio: 16/9 4/3
Lens:2.1mm
FOV:170°
Aperture:F2.0
Shutter Rolling: Rolling shutter
Min.Illumination: 0.001Lux
Weight: 1.8g
Dimensions: 14x14x16mm
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 HD 1S 1.6" Deadcat Micro Quad w/ Walksnail Avatar Mini 1S Lite & Avatar Lite Cam - ELRS 2.4 GHz
4x 1608 -3 40mm 1.5mm shaft
2x TPU battery mount
1x hardware screws set
4x Prop guards
The FR16 Nano Baby V2 is a meticulously crafted microdrone with improved appearance, flight time, and power compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy reinforces camera protection, while a new bottom plate adds sturdiness and crash resistance. The drone is equipped with a special gold-purple edition ROBO 1002 23,500KV motor and GOKU Versatile F411 VTX 1S AIO V2 with 250mW video transmitter. The Flywoo 1S Nano camera V3 delivers clearer and better image quality on this quad.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability.
Ultra-light GOKU Versatile F411 1S VTX AIO V2 with upgraded circuit board stability and a 250mw video transmitter, enabling an extended flight range.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
Upgraded Flywoo 1S Nano camera V3 delivers clearer and better image quality.
New battery compartment design allows for easy replacement of batteries of different models.
Specification
Motor: ROBO 1002 23500KV
Electronics: GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/250mW VTX
Props: 1609 - 4 blade 40mm 1.5mm Shaft
Camera: Flywoo 1S Nano Camera V3
Receiver: ExpressLRS 2.4GHz
Weight: 26g
Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate)
Speed: 80km/h (approximate)
GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/ 250mw VTX
Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port：1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HV Current: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
Onboard 5.8g VTX
Output power: 25mw~250mw switchable
Frequency: 40CH
Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready
Flywoo ROBO 1002 23500KV Fpv Motor:
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.5
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 52
Internal Resistance: 75mΩ
Max Current(3S): 14A
Max Efficiency Current: (2-4A)>84%
Flywoo 1S Nano Camera V3
Model: Flywoo 1S Nano Camera V3
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC and PAL(switchable)
MENU: Support
IMAGE: 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio: >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm/F2.5
Min. illumination: 0.001Lux
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14x14mm
Wide Power Input: DC 3.7-18V
Work Temperature: -20°C~+60C
Work Humidity: 20%~80%
Weight: 2.1g
Includes
1x Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz
4x 1609 - 4 40mm 1.5mm shaft
2x TPU Battery Mount
1x Hardware Screw Set
4x Prop guards
The Firefly 1S Nano Baby V2 is a micro-drone with improved flight time, power and design compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy for camera protection and a bottom plate for sturdiness are integrated. Additionally, this model includes the GOKU F411 ELRS 1S AIO V2 with ELRS 2.4G receiver (UART 2) for a lightweight design with optimal performance. This version utilizes the elite capabilities of the HDZero HD digital VTX system. The HDZero Nano Lite Camera is a revolutionary product designed for lightweight drones, weighing only 1.5g and combined with the new Whoop Lite VTX at 4.5g. Supporting 1-3S power input, it can record in 720P/60FPS with ultra-low latency of less than 19ms and features OSD function configuration through Betaflight Configurator.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features:
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds - perfect for racing competitions.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Specifications
Motor: ROBO 1002 23,500KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Props: 1609 - 4 blade 40mm 1.5mm Shaft
HD Digital VTX System: HDZero Whoop Lite Bundle
Receiver: ExpressLRS 2.4GHz
Weight: 31g
Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate)
Speed: 70km/h (approximate)
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
Flywoo ROBO 1002 23500KV Fpv Motor:
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.5
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 52
Internal Resistance: 75mΩ
Max Current(3S): 14A
Max Efficiency Current: (2-4A)>84%
HDZero Whoop LITE VTX
Input Voltage: 1S-3S
Output Power: 23mW, 200mW
Operating Frequency: 5.727-5.850GHz
Resolution: 1280x720@60fps
Power Consumption: 5W @ 25mW, 5.8W @ 200mW
MSP Canvas Mode: Yes
Antenna Interface: U.FL (IPEX 1)
Operating Temperature: 32-104°F
Mounting Pattern: 25x25mm, M2
Weight: 7g total package
HDZero Nano LITE Camera
Size: 14x16x11mm
Weight: 1.5gram
Sensor: 0.5 inch, up to 10650 mV/Lux-secUltra-high sensitive CMOS sensor
FOV:- 4:3 D:130° H:108° V:84°- 16:9 D:122° H:108° V:65°
Includes
1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ HDZero Whoop Lite & Nano Lite Cam - ELRS 2.4 GHz
4x 1609 - 4 40mm 1.5mm shaft
2x TPU Battery Mount
1x Hardware Screw Set
4x Prop guards
The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system. The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting.
Check out our other pre-built quads, as well as other great products from Flywoo!
Features
Redesigned canopy with enhanced aesthetics and reinforced camera protection.
The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter.
Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions.
The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.
A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector.
New battery compartment design allows for easy replacement of batteries of different models.
Specification
Motor: ROBO 1002 23500KV
Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0
Props: 1609 - 4 blade 40mm 1.5mm Shaft
HD Digital VTX System: Walksnail Avatar HD Mini 1S Lite
Receiver: ExpressLRS 2.4GHz
Weight: 33g
Flight Time: Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate)
Speed: 70km/h (approximate)
GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller
MCU: STM32F411CEU6
GYRO: ICM42688
UARTS: 1/2
Soft serial port: 1
I2C: SCL/SDA
BEC: 5V
Input Voltage: 1S (<4.35v)
Firmware: FLYWOOF411_5IN1_AIO
Mounting: 25x25mm, M2
Onboard 4in1 ESC
MCU: EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A
Firmware: BLHeli_S
Factory firmware: O_H_5_REV16_8.HEX
Default protocol: DSHOT 150/300/600
ELRS 2.4G RX (UART2)
Flywoo ROBO 1002 23500KV Fpv Motor:
Configuration: 9N12P
Stator Diameter: 10mm
Stator Length: 2mm
Shaft Diameter: 1.5mm
Motor Dimension(Dia.xLen): Φ13.5x7.75mm
Weight(g): 2.5(5cm wire)
Idle current(5)@5V(A): 1.5
No.of Cells(Lipo): 1S
Max Continuous Power(W)3S: 52
Internal Resistance: 75mΩ
Max Current(3S): 14A
Max Efficiency Current: (2-4A)>84%
Walksnail Avatar HD Mini 1S Lite
Model: Avatar mini 1s module
Communication Frequency: 5.725-5.850GHz
Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm;
MIC:<25dBm
I/O Interface: JST1.0x6(Power in)JST1.0x4(USB)
Mounting Holes: 25.5x25.5mm
Dimensions: 30x30x6.5mm
Storage: 8G
Recording: 1080p/720p
Weight: 5.1g
Operating Temperature: -20-40℃
Channels: 8
Wide Power Input: 3.1V-5V
Supported FC System: Betaflight
OSD: Canvas mode
Bitrate: 25mbps, 50mbps
Latency Average delay: 22ms
Antenna: IPEX
Avatar lite camera
Model: Avatar lite camera
Image Sensor: 1/2.7”1nch
Resolution: 1080P/60fps,720P/120fps,720P/60fps
Ratio: 16/9 4/3
Lens:2.1mm
FOV: 170°
Aperture: F2.0
Shutter Rolling: Rolling shutter
Min.Illumination: 0.001Lux
Weight: 1.8g
Dimensions: 14x14x16mm
Includes
1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz
4x 1609 - 4 40mm 1.5mm shaft
2x TPU Battery Mount
1x Hardware Screw Set
4x Prop guards
Flywoo's Firefly Hex Nano V1.2 is the smallest hexacopter ever designed by Flywoo, weighing in at 74g. It powerfully and stably carries Insta 360go and SMO 4K cameras. The Firefly hex nano is small, flexible, stable, and is full of power and offers unmatched control.
Check out our other pre-built quads, as well as other great products from Flywoo!
Feature
Hexacopter
HD system
Naked Vista
Weighing only 74 grams
Built in SMO Power Cable
Prebuilt and tested
Specifications
Weight: 74g
Wheelbase: 80mm
FC & ESC:【No.C203】GOKU HEX F4 16x16 STACK - ( FC+13A ESC ) ( MPU6000)
Frame: Firefly Baby Quad Frame (HD Verison)
Motors: Nin V2 1203Pro 5500Kv
Props: Gemfan 1636 40mm-4 V2.0
HD digital camera & VTX: Naked RunCam Link & RunCam Wasp
Antenna: Atomic 5.8GHz Antenna Length 30mm (LHCP)
Battery (Recommended): 4S 450mAh / 4S 300mAh battery (Not including)
GOKU HEX GN405 Nano16X16 FC
MCU: STM32F405 BGA
IMU: ICM42688P
Barometer: DPS310
input voltage： 2-6S
Onboard LED：WS2812x4
6 hardware UARTS (UART1,2,3,4,5,6)
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only.
PPM and PWM receivers are not supported.
Onboard 16Mbytes for Blackbox logging
5V Power Out: 2.0A max
3.3V Power Out: 0.5A max
Dimensions: 22x22mm
Mounting Holes: 16x16mm
Weight: 2.3g
Firmware : FLYWOOF405NANO
BS13A BLheli_S 2-4S 4in1
lBS20/35A BLheli_S 2-6S 4in1
Weight: 2.5g
Mounting Hole: 16x16mm (M3)
Support Oneshot, Multishot,
DShot150/300/600
Nin V2 Motor
Stator Size: 1203
Motor Bolt Pattern: 9x9mm
KV: 5500
Wasp Nano HD Camera
Dimensions: L18mmxW14mmxH18mm
LENS: FOV D:160° H:127° V:92°
Resolution: 720P@120fps(4:3)
Net Weight: 6g(With Cable)
Shutter: Rolling Shutter
Coaxial Cable: 80 mm
Image Sensor: 1/3"
Naked Link Air Unit
Input Voltage: 7.4-26.4V@ 4-9W
Operating Frequency: 5.725-5.850 GHz
Transmitter Power: (EIRP) FCC/SRRC: <30 dBm; CE: <14 dBm
Min. Latency (end-to-end): 1280 x 720 60fps: 32 ms
Max. Transmission Distance: FCC/SRRC: 4 km; CE: 0.7 km;
I/O Interface: Type-C, IPEX, 3-in-1 port,
Supported Flight Control System: BetaFlight
Operating Temperature Range: 0° to 40° C (32° to 104° F)
Includes
1x Flywoo BNF Firefly Hex Nano V1.2 1.6" HD 4S Micro Quad w/ Naked RunCam Link & RunCam Wasp - Choose Receiver
1x Accessories (props, prop guard, RunCam link shell, battery straps, hardware, ect)
Tiny module with compass and barometer from Flywoo!
If your FC board has a barometer, you need to disconnect the Baro SDA / SCL pad.
Check out all our Flywoo products!
Specifications
Baro: BMP280
Compass QMC5883L
Power supply: 3.3V-5V
Communication: I2C protocol
Pin: SH1.0-4
Module size: 11x15.5mm
Weight: 0.6g
Includes
1x Flywoo BQNANO V1.0 Compass and Barometer
Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card.
The CineRace is a double duct design, not a simple guard anymore. It can fly as flexibly as a racing drone, and as stable as Cinewhoop. All in all, this is a drone that can not only race but also capture stable videos and at the same time achieve a super long flight time! A specially designed GM10 Nano V3 GPS module is tailored to fit the CineRace20, providing minimal weight but the ability to search up to 30 satellites. You will see on the front of the quad Flywoo engineer the use of the soft TPU material to mount the camera to prevent the jello effect, by reducing the over all vibrations in the quad.
Come see our Cinewhoop Collection and other great products from Flywoo!
We also carry a version with the O3 Air Unit already installed here.
Features
Almost all parts are injection molded for a more sturdy and durable quad.
Very easy to disassemble, only fixed by two aluminum columns
Customizable with LEDs
GPS up to 30 satellites
Innovative duct design
Sub250 (even with battery)
Specifications
Input Voltage: 4S
Model: CineRace20 HD DJI O3 2inch (without Air Unit)
Brand: FLYWOO
Frame: CineRace20 O3 (Different fromCineRace20 V1.2\V2 frame )
Charge connector: XT30
Motor: NIN V2 1203PRO 4850Kv
Propeller: D51-5 51mm
Buzzer : 5PCS Active Alarm Buzzer
GPS: GOKU GM10 Nano V3 GPS
Weight: 139g (without battery)
Betaflight Firmware target: FLWO/FLYWOOF405S_AIO(SMT32F405)
Recommended Battery:Explorer 450mah 4S ( flight time 5mins ) Explorer 750mah 4S ( flight time 6mins )
GOKU GN F405S 20A AIO
Input Voltage: 2-6S Lipo
MCU: STM32F405 BGA
IMU: ICM42688
OSD: BetaFlight OSD
Blackbox: 16Mb Flash
Baro: BMP280
BEC: 5V
6 hardware UARTS (UART1,2,3,4,5,6)
Onboard LED：4x WS2812
Support BLHELI_S
Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
FPV System
Add your own O3 Air Unit
Includes
1 x Flywoo CineRace20 HD V2 Neon LED 4S Cinewhoop (without O3 Unit) - PNP
8 x D51-5 props
2 x Battery strap 9x150mm \ 9x200mm
1 x Set of screws
1 x 90° USB Type-C
Flywoo Circular Antenna is the market's most miniature and lightest circular polarized antenna. Only 1.6g (without Tube). Perfect for both lightweight racing builds or freestyle quads.
Check out our ever-expanding selection of VTX antennas and our Flywoo gear selection!
Specifications
Gain: 2.2dBi
Axial ratio: 1.0 Around
Band Width: 5.6Ghz – 6.2GHz
Axial Ratio: Around 1.0
Polarization: LHCP or RHCP
Connector: UFL
Weight: 1.6g (without Tube)
Includes
1x Flywoo Circular 5.8GHz U.FL Antenna - LHCP 115mm / 45mm Tube
Flywoo has just released their RGB motor LEDs compatible with any 9x9mm motor! Add these LEDs to your drones for more visibility and super glow aesthetics!! The TPU motor skids protect these LEDs and will diffuse those cool colors making your drone look next level!!
Don't forget to check out our other LEDs and Flywoo Products!
Specifications
Hole: M2 / 9x9mm
Weight: 1g
Input Voltage: 5v (over 5v will burn the LEDs)
Betaflight LED control
Includes
4x Flywoo Digital RGB Motor LEDs
4x 3 conductor connection wire
4x Tpu protect mount
Convert any frame to use DJI O3 Air unit. Don't worry if your frame has the right holes!
Specifications
Item Name: Flywoo DJI O3 Air Unit 20x20 16x16 adapter plate Quantity: 3pcsThe Thickness of the Plate: 1mmWeight: 0.7g
Includes
3x Flywoo DJI O3 Air Unit 20x20 / 16x16 Adapter Plate1x screw pack
Flywoo has specially designed the Flywoo ND filters for the DJI O3 Air Unit!
Choose your ND filter, as we have the UV, ND4, ND8, and ND16 individually for you to choose.
Clear UV Filter: Protects your camera lens from dust, dirt, and scratchesND4 Filter: Ideal for dark, cloudy daysND8 Filter: Perfect for cloudy days or early morning/late afternoon sunlightND16 Filter: Suitable for use on bright, sunny days
These filters also act as a lens protector that can protect your lens when your drone has a severe crash. The UV filter can protect your lens while you fly indoors or at dusk, providing pilots with clearer footage.
Whether you are using the ND filter for FPV drones, mountain biking footage or other action video, this will give you that smooth as silk, cinematic motion and reduce or eliminate jello.
Check out other DJI O3 Products!
Check out the rest of our replacement cam parts & accessories, as well as the rest of our Flywoo selection!
Features
Protects your camera lense
Fits all O3 Air unit drones
Super tight fit
Easy to use
Light weight
Specifications
Adapt : DJI O3 Air unit \ DJI Avatar drone
Size: 32mm x 34mm
Weight: 0.6g
Includes
1x Flywoo DJI O3 Air Unit Camera Filters - Choose Your ND
Flywoo has specially designed the Flywoo ND filter set for the DJI O3 Air Unit! This set consists of 3 Pieces: the ND16, ND32, and CLP filters. These filters also act as a lens protector that can protect your lens when your drone has a severe crash.
Whether you are using the ND filter for FPV drones, mountain biking footage or other action video, this will give you that smooth as silk, cinematic motion and reduce or eliminate jello.
ND16 Filter: Suitable for use on bright, sunny days
ND32 Filter: Designed for exceptionally bright conditions, such as snow or water reflections
CPL Filter: Enhances color saturation and contrast by reducing glare from reflective surfaces
Check out our other DJI O3 Products!
Check out the rest of our replacement cam parts & accessories, as well as the rest of our Flywoo selection!
Features
Protects your camera lens
Fits all O3 Air unit drones
Super tight fit
Easy to use
Light weight
Specifications
Adapt : DJI O3 Air unit \ DJI Avatar drone
Size: 32mm x 34mm
Weight: 0.6g
Includes
1x Flywoo DJI O3 Air Unit Filters Set (3pc) - ND 16/32 + CLP
1x Micro Fiber Cloth
Flywoo has specially designed the Flywoo ND filter set for the DJI O3 Air Unit! This set consists of 3 Pieces: the ND4, ND8, and UV filters. These filters also act as a lens protector that can protect your lens when your drone has a severe crash.
Whether you are using the ND filter for FPV drones, mountain biking footage or other action video, this will give you that smooth as silk, cinematic motion and reduce or eliminate jello.
ND4 Filter: Ideal for dark, cloudy days
ND8 Filter: Perfect for cloudy days or early morning/late afternoon sunlight
Clear UV Filter: Protects your camera lens from dust, dirt, and scratches
Check out our other DJI O3 Products!
Check out the rest of our replacement cam parts & accessories, as well as the rest of our Flywoo selection!
Features
Protects your camera lens
Fits all O3 Air unit drones
Super tight fit
Easy to use
Light weight
Specifications
Adapt : DJI O3 Air unit \ DJI Avatar drone
Size: 32mm x 34mm
Weight: 0.6g
Includes
1x Flywoo DJI O3 Air Unit Filters Set (3pc) - ND 4/8 + UV
1x Micro Fiber Cloth
Flywoo has specially designed the Flywoo ND filter set for the DJI O3 Air Unit! This set consists of 7 Pieces: the ND4, ND8, ND16, ND32, ND64, CPL, and UV filters. These filters also act as a lens protector that can protect your lens when your drone has a severe crash. The UV filter can protect your lens while you fly indoors or at dusk, providing pilots with clearer footage.
Whether you are using the ND filter for FPV drones, mountain biking footage or other action video, this will give you that smooth as silk, cinematic motion and reduce or eliminate jello.
ND4 Filter: Ideal for dark, cloudy daysND8 Filter: Perfect for cloudy days or early morning/late afternoon sunlightND16 Filter: Suitable for use on bright, sunny daysND32 Filter: Designed for exceptionally bright conditions, such as snow or water reflectionsND64 Filter: Excellent for capturing long exposure shots in bright environmentsCPL Filter: Enhances color saturation and contrast by reducing glare from reflective surfacesClear UV Filter: Protects your camera lens from dust, dirt, and scratchesLens Wipes: For maintaining the cleanliness of your filters and ensuring optimal image quality
Check out our other DJI O3 Products!
Check out the rest of our replacement cam parts & accessories, as well as the rest of our Flywoo selection!
Features
Protects your camera lens
Fits all O3 Air unit drones
Super tight fit
Easy to use
Light weight
Specifications
Adapt : DJI O3 Air unit \ DJI Avatar drone
Size: 32mm x 34mm
Weight: 0.6g
Includes
Flywoo DJI O3 Air Unit Filters Set (7PCS) - ND 4/8/16/32/64 + CPL + UV
1x Clear UV Filter
1x Carrying case
1x Lens Wipes
1x ND16 Filter
1x ND32 Filter
1x ND64 Filter
1x ND4 Filter
1x ND8 Filter
1x CPL Filter
These Cables are digital HD video cables that work with the DJI O3 system.
The DJI O3 Coaxial Camera Cable is a replacement or spare for the DJI O3 Air Unit.
Make sure to check out the rest of our Flywoo selection!
Features
10/15/20/30cm Cable Length Options
Works with the DJI O3
Specifications
Compatibility: DJI O3
Length Options:
100mm (10cm)
150mm (15cm)
200mm (20cm)
300mm (30cm)
60mm(6cm)
Includes
1x DJI O3 Coaxial Cable (Choose length)
The new Flywoo TCXO 2.4G ELRS utilizes a temperature-compensated crystal oscillator to enhance the accuracy of the MCU clock frequency, thereby improving the performance and reliability of the RC link. It enables longer control distances, allowing users to operate devices within a wider range. This module boasts low latency and high refresh rates.
The TCXO EL24E features a built-in SMD antenna and is based on the ESP8285 MCU and can be upgraded via WiFi. They are also equipped with the SX1280 (or SX1281) IMLTRT RF module.
Check out the rest of our receivers, as well as the rest of our Flywoo selection!
Features
Enhances MCU clock frequency accuracy
Improves RC link performance and reliability
Enables longer control distances
Low latency and high refresh rates
EL24E: built-in SMD antenna
Based on ESP8285 MCU
Upgradeable via WiFi
Equipped with SX1280 (or SX1281) IMLTRT RF module.
Specifications
Type: ISM2.4GHz
ESP8285 MCU
SX1280(SX1281)IMLTRT RF Module
Frequency Range: 2400 MHz to 2500 MHz
Receive refresh rate: 25HZ~500Hz
Working voltage: 5V
Weight: 0.44 gram(without antenna)
Dimension: 10mmx10mmx6mm
Communication Protocol: CRSF(Betaflight)
Peak gain: 3.7dB
Default Firmware out of the factory: Flywoo EL24E 2.4GHz RX 3.0.0
Built-in a TCXO (temperature-compensated crystal oscillator)
Includes
1x Flywoo EL24E TCXO V2 ELRS 2.4GHz Micro Receiver - Ceramic Antenna
1x Silicone Cable
1x Heat shrink tubing
The Flywoo 2.4GHz ELRS nano series receiver is an open-source program based on the lightweight and minuscule ExpressLRS. Using the ESP8285 MCU, SX1280 RF CHIP, and IPEX ports, you can connect external T-type antennas for more range, and a stronger signal.
Check out the rest of our receivers, as well as the rest of our Flywoo selection!
Specifications
Type: ISM
MUC: ESP8285
RF Module: SX1280IMLTRT
Antenna Connector: IPEX
Frequency Range: 2400 MHz to 2500 MHz
Maximum Receive Refresh Rate: 500Hz
Minimum Receiver Refresh Rate: 25Hz
Working Voltage: 5V
Peak gain: 3.7dB
Dimension: 10.8x11x6mm
Weight: 0.4g
Includes
1x Flywoo ELRS EL24P 2.4GHz Micro Receiver
All batteries must be shipped by a ground shipping method.
Explorer series batteries are specially designed for long flight time and all are high voltage batteries. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery.
Check out our other 1S batteries, as well as the rest of our Flywoo selection!
Specifications
Nominal Voltage: 3.8V
Cells: 1S
Capacity: 450mAh
Discharge Rate: 80C
Composition: LiHV
Discharge Lead: GNB27 30mm
Dimensions: 59x18x6.8mm
Weight: 13.2g
Includes
4x Flywoo Explorer 4.35V 1S 450mAh 80C LiHV Battery - GNB27
Experience long-range cruising with the Flywoo Explorer LR Analog Frame Kit, a collaboration between Flywoo and Dave_C FPV, this ultra-light 4" frame is designed to help you push your FPV skills to the max, without compromising on noise and portability. Made with 100% 3K carbon fiber and 7075 aluminum alloy, the Explorer LR lets you take off and enjoy the thrill of a long-range FPV adventure.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Specifications
Thickness of arms: 3mm
Thickness of top plate: 1.5mm
Thickness of bottom plate: 1.5mm
Weight: 41g
Electronic Mounting: 16x16mm, 20x20mm
VTX Mounting: 16x16mm, 20x20, 25.5x25.5mm
Motor Bolt Pattern: 9x9mm, 12x12mm
Material: 100% 3K carbon fiber, 7075 aluminium alloy
Message from Dave_C FPV:
"For me personally, Long Range cruising through epic landscapes is the best thing about FPV! But unfortunately, it was always kind of difficult to practice legally and without bothering people with all the noise a massive 6 or 7" long-range quad produces.
So the basic idea behind the original Project #MicroLongRange was born: Scale down a 7" long-range quad until it is below 250g take-off weight. With the support of an awesome community on Facebook and Instagram as well as a massive development effort by Flywoo, this concept has seen a lot of improvements that are now all implemented in the Explorer LR!
This tiny quad is equipped with GPS, Crossfire, and an independent model finder to give you the necessary confidence to push it to the maximum range of digital and analog video transmission. The powertrain with its GOKU 16x16 stack and the all-new 2700kV 1404 motors spinning 4" props is optimized for maximum efficiency and low weight: Flight times of way over ten minutes on a regular 850mah 4S LiPo battery are easily achievable! Cruising speeds of 40-50 kph (25-30mph) are astonishingly high for such a small quad and have allowed me to do 10km (6 miles) round trips easily. And the best thing about it: It's incredibly quiet! You will barely be able to hear it flying by as soon as you are a few dozen meters away. ”
----- Dave_C FPV
Includes
1x Flywoo Explorer LR 4" Walksnail Long Range Frame kit
1x Black TPU 3D Printed Parts
1x M2x5: 8pcs
1x M2x7: 8pcs
1x M2x8: 6pcs
1x M2x12:12pcs
1x Aluminum Standoffs M2*20: 4pcs
1x Aluminum Standoffs M2*25: 2pcs
1x TPU 3D Printed Parts :1 package
1x Flywoo Atomic 5.8G UFL Ant 1 ( RHCP )
Experience long-range cruising with the Flywoo Explorer LR HD Frame Kit, a collaboration between Flywoo and Dave_C FPV, this ultra-light 4" frame is designed to help you push your FPV skills to the max, without compromising on noise and portability. Made with 100% 3K carbon fiber and 7075 aluminum alloy, the Explorer LR lets you take off and enjoy the thrill of a long-range FPV adventure.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Specifications
Thickness of arms: 3mm
Thickness of top plate: 1.5mm
Thickness of bottom plate: 1.5mm
Weight: 41g
Electronic Mounting: 16x16mm, 20x20mm
VTX Mounting: 16x16mm, 20x20, 25.5x25.5mm
Motor Bolt Pattern: 9x9mm, 12x12mm
Material: 100% 3K carbon fiber, 7075 aluminium alloy
Message from Dave_C FPV:
"For me personally, Long Range cruising through epic landscapes is the best thing about FPV! But unfortunately, it was always kind of difficult to practice legally and without bothering people with all the noise a massive 6 or 7" long-range quad produces.
So the basic idea behind the original Project #MicroLongRange was born: Scale down a 7" long-range quad until it is below 250g take-off weight. With the support of an awesome community on Facebook and Instagram as well as a massive development effort by Flywoo, this concept has seen a lot of improvements that are now all implemented in the Explorer LR!
This tiny quad is equipped with GPS, Crossfire, and an independent model finder to give you the necessary confidence to push it to the maximum range of digital and analog video transmission. The powertrain with its GOKU 16x16 stack and the all-new 2700kV 1404 motors spinning 4" props is optimized for maximum efficiency and low weight: Flight times of way over ten minutes on a regular 850mah 4S LiPo battery are easily achievable! Cruising speeds of 40-50 kph (25-30mph) are astonishingly high for such a small quad and have allowed me to do 10km (6 miles) round trips easily. And the best thing about it: It's incredibly quiet! You will barely be able to hear it flying by as soon as you are a few dozen meters away. ”
----- Dave_C FPV
Includes
1x Flywoo Explorer LR 4" Walksnail Long Range Frame kit
1x Black TPU 3D Printed Parts
1x M2x5: 8pcs
1x M2x7: 8pcs
1x M2x8: 6pcs
1x M2x12:12pcs
1x Aluminum Standoffs M2x20: 4pcs
1x Aluminum Standoffs M2x25: 2pcs
1x TPU 3D Printed Parts :1 package
1x Flywoo Atomic 5.8G UFL Ant 1 ( LHCP)
The Flywoo Explorer LR HD O3 Deadcat Long Range 4" Frame kit is designed to fit the DJI O3 Air unit and accommodate 16x16 and 20x20 flight towers. This compact frame allows you to enjoy the experience of long-range FPV flying without disturbing others or running into legal troubles. Cruise through landscapes with ease and explore with minimal noise.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Includes
1x Flywoo Explorer LR HD O3 Deadcat Long Range 4" Frame Kit
1x Black TPU 3D Printed Parts
1x Top plate
1x Bottom plate
1x central plate
2x Front arms
2x Rear arms
2x Side plate
2x Battery straps
1x hardware sets
1x Battery pad
2x insulation sheet
Replacement part for the Flywoo Explorer LR HD O3 Deadcat Long Range 4" Frame Kit, Pieces go missing or break when you choose fun over risk, so we got you covered with this replacement bottom plate.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Includes
1x Flywoo Explorer LR O3 Replacement Bottom Plate
Replacement part for the Flywoo Explorer LR HD O3 Deadcat Long Range 4" Frame Kit, Pieces go missing or break when you choose fun over risk, so we got you covered with this replacement center plate.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Includes
1x Flywoo Explorer LR O3 Replacement Center Plate
Replacement part for the Flywoo Explorer LR HD O3 Deadcat Long Range 4" Frame Kit, Pieces go missing or break when you choose fun over risk, so we got you covered with 2 replacement side plates.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Includes
1x Flywoo Explorer LR HD O3 Replacement Side Plate (2pc)
Replacement part for the Flywoo Explorer LR HD O3 Deadcat Long Range 4" Frame Kit, Pieces go missing or break when you choose fun over risk, so we got you covered with this replacement top plate.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Includes
1x Flywoo Explorer LR O3 Replacement Top Plate
Replacement part for the Flywoo Explorer LR HD O3 Deadcat Long Range 4" Frame Kit, Pieces go missing or break when you choose fun over risk, so we got you covered with 2 rear replacement arms.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Includes
1x Flywoo Explorer LR O3 Replacement Rear Arm (2pc)
Pair of replacement front arms for the Flywoo Explorer LR V2 4" Frame
Check out all our Flywoo products!
Includes
2x Flywoo Explorer LR V2 Front Arm (2pc)
The Flywoo Explorer LR HD Walksnail Deadcat Long Range 4" Frame kit is designed to fit the Walksnail VTX and accommodate 16x16 and 20x20 flight towers. This compact frame allows you to enjoy the experience of long-range FPV flying without disturbing others or running into legal troubles. Cruise through landscapes with ease and explore with minimal noise.
Check out the rest of our 4" frames, as well as other great products from Flywoo!
Includes
1x Flywoo Explorer LR 4" Walksnail Long Range Frame kit
1x Black TPU 3D Printed Parts
1x Top plate
1x Bottom plate
1x central plate
2x Front arms
2x Rear arms
2x Side plate
2x Battery straps
1x hardware sets
1x Battery pad
2x insulation sheet
All batteries must be shipped by a ground shipping method.
Explorer series batteries are specially designed for long flight time and all are high voltage batteries. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery.
Check out our other 1S batteries, as well as the rest of our Flywoo selection!
Specifications
Nominal Voltage: 3.8V
Cells: 1S
Configuration: 1S1P / 4.35V / 1 Cell
Capacity: 450mAh
Discharge Rate: 80C
Composition: LiHV
Weight: 13.2g
Connector: A30
Includes
1x Flywoo Explorer 3.8V 1S 450mAh 80C LiHV Battery 4 Pack - A30
All batteries must be shipped by a ground shipping method.
Explorer series batteries are specially designed for long flight time and all are high voltage batteries. Using this battery will give you a significant increase in flight time as well as a bit more power over the stock battery.
Check out our other 1S batteries, as well as the rest of our Flywoo selection!
Specifications
Nominal Voltage: 3.8V
Cells: 1S
Configuration: 1S1P / 4.35V / 1 Cell
Capacity: 750Ah
Discharge Rate: 80C
Composition: LiHV
Weight: 14g
Connector: A30
Includes
1x Flywoo Explorer V2 3.8V 1S 450mAh 80C LiHV Battery 4 Pack - A30
Multipurpose buzzer from Flywoo, never lose your quad again.
Check out the rest of our Buzzers & Alarms and our Flywoo gear selection!
Features
100dB Buzzer w/ built in LED
Active/Passive Buzzer Functionality
Charges when plugged into flight controller
Specifications
Buzzer dB: 100 dB
Size: 21*11*9.5MM
Weight: 2.7 grams
Includes
1x Flywoo Finder V1.0 Buzzer w/ LED
Instructions for use
The buzzer has two modes of operation:
1. It is compatible with the functions of the traditional active buzzer and synchronized with the flight control.2. When the flight control is normally connected, if the main battery in the flight is powered off, it can still automatically emit 100 dB of drip sound after 30 seconds of power failure, and the LED will emit white light.To turn off the buzzer: Press and hold the release button for more than 2 seconds, the Finder V1.0 turns off the sound.The Finder is compatible with all BF and CF flight controls. Just connect to the buzzer interface of the flight controller and it will work. When the flight control wiring is correct, the multi-rotor aircraft is powered on, and the flight control power supply will be automatically charged for the Finder (the red LED will light to indicate charging is in progress, the red light is off to indicate charging saturation; the red light flashing indicates flight control) Electricity, enter 30 seconds waiting time).
Build your own version of the Firefly DC16 micro quad, with this micro frame kit.
Check out our other Micro frames, as well as other great products from Flywoo!
Feature
Compatible with 40mm propellers
Specifications
Weight: 3.7g
Motor Bolt Pattern: 6mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 1.6" Analog Micro Frame Kit
Build your own version of the Firefly DC16 micro quad, with this micro frame kit.
Check out our other Micro frames, as well as other great products from Flywoo!
Feature
Compatible with 40mm propellers
Specifications
Weight: 3.7g
Motor Bolt Pattern: 6mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Flywoo BNF Firefly DC16 Nano Baby V2.0 1.6" HDzero Micro Frame Kit
