GEA4S220045D, Gens Ace 4S LiPo Battery 45C (14.8V/2200mAh) w/Deans
Gens Ace batteries have been proven within the Radio Control community to deliver reliable and consistent performance for all modelers alike. All Gens Ace batteries offer superior cell matching at the factory, and are extremely consistent in selecting matched cells after each and every batch produced. Additionally, low internal resistance (IR), offers modelers stable voltage output through the whole duration of the battery.
Specifications: Voltage: 14.8VDischarge Rate: 45CCell Count: 4S1PCapacity: 2200mAhDimensions: 106x34x30mm (LxWxH)Weight: 260gPlugs: Deans
This product was added to our catalog on May 8, 2024
GEA4S680012E5, Gens Ace 4S Bashing Pro LiPo Battery Pack 120C (14.8V/6800mAh) w/EC5 Connector
The Gens Ace Bashing Pro 4s has been specifically designed for Arrma vehicles that can utilize a high-capacity battery. All GensAce batteries offer superior cell matching at the factory, and are extremely consistent in selecting matched cells after each and every batch produced. Additionally, low internal resistance (IR), offers modelers stable voltage output through the whole duration of the battery.
Features:
Large-capacity battery specially designed for ARRMA vehicles to maximize battery life.
Better grip in the battery tray.
PC material and silicon rubber case provides dual protection.
Specifications:
Nominal Voltage: 14.8V (4S)
Capacity: 6800mAh
Maximum Charge Rate: 1C (6.8A)
Discharge Rate:
Continuous: 120C
Peak: (Not Available)
Cell Configuration: 4S1P
Watt Hours: 100.64Wh
ROAR Approved: No
Connector:
Battery: EC5
Balance: XHR
Dimensions (LxWxH): 6.18x1.85x1.61in (157x47x41mm)
Weight: 23.74oz (673g)
This product was added to our catalog on January 18, 2023
GEA75004S10D5, 15.2V 7500mAh 4S 100C HV Lipo: DEANS
Gens Ace batteries have been proven within the Radio Control community to deliver reliable and consistent performance for all modelers alike. All Gens Ace batteries offer superior cell matching at the factory, and are extremely consistent in selecting matched cells after each and every batch produced. Additionally, low internal resistance (IR), offers modelers stable voltage output through the whole duration of the battery.
Specifications:
Voltage: 15.2V / 4S1P / 4 Cell
Discharge Rate: 130C
Max Burst Discharge Rate: 200C
Capacity: 7500mAh
Dimensions: 139x47x48.5mm (LxWxH)
Weight: 584g
Plugs: 5mm Bullets with T-Style Adapter
This product was added to our catalog on November 18, 2021
GEA8K4S10E5GT, Gens Ace G-Tech Smart 4S LiPo Battery 100C (14.8V/8000mAh) w/EC5 Connector
Gens Ace batteries have been proven within the Radio Control community to deliver reliable and consistent performance for all modelers alike. All Gens Ace batteries offer superior cell matching at the factory, and are extremely consistent in selecting matched cells after each and every batch produced. Additionally, low internal resistance (IR), offers modelers stable voltage output through the whole duration of the battery.
Smart G-Tech Technology Features:
Automatic identification and recording of all battery parameters
Adjusting charging parameters to improve safety
Balance plug with built-in chip and exclusive patented design technology
Protects and extend the battery life
Specifications:
Nominal Voltage: 14.8V (4S)
Capacity: 8000mAh
Maximum Charge Rate: 5C (40A)
Discharge Rate:
Continuous: 100C
Peak: 200C
Cell Configuration: 4S2P
Watt Hours: 118.4Wh
ROAR Approved: No
Connector:
Battery: EC5
Balance: G-Tech Smart Connector
Dimensions (LxWxH): 6.26x2.13x1.69in (159x54x43mm)
Weight: 26.53oz (752g)
This product was added to our catalog on July 19, 2023
Gemfan truly believes that there is a perfect prop for every situation. And to that end, the new Freestyle 4S 5136 prop adds a new choice to pick from. Gemfan continues to offer the perfect blend of form and function.
Check out the rest of our 5" props, and all our Gemfan selections!
Specifications
Propeller diameter: 5.1in
Pitch: 3.6in
Blades: 3
Material: Polycarbonate
Weight: 3.6g
Hub Thickness: 6mm
Shaft: 5mm
Includes
4x Gemfan Freestyle 4S 5136 Tri-Blade 5" Props
A budget and user-friendly charger for all your FPV needs!
The Imars Mini Charger, from Gens Ace, has been designed specifically for Gens Ace G-Tech smart batteries while also compatible with non-smart batteries.
It is the first member of the Gens ace G-Tech Smart Eco, when the Gens ace G-Tech battery is connected to the Imars Mini charger, the charger will automatically identify the battery type, voltage through the smart balance connector, and charging current recommended by the battery manufacturer. The charger will start charging in 5 seconds automatically after G-Tech smart battery is connected.
For non-smart batteries, it's necessary to manually select the battery type and the required working mode to get it started. The charger can intelligently adjust the charging current according to the charging voltage flow of the battery.
Check out our other battery chargers and accessories!
Features
Charges 2-4S LiPo, LiHV, LiFe, and 2-12S NiMH batteries.
Intelligently recognizes G-Tech smart battery info through an IC chip for safe and easy charging.
Automatic storage function, it's the smallest charger with auto storage.
New interface design and increased balance connector durability.
Small & lightweight, portable design.
Specifications
Max. Charge Power: 60W
Charge Current: 1-5A, Max. 5A(Auto Adjustment)
Max. Storage Power: 3W discharge, 60W charge
Input Voltage: 5-20V
Max. Input Current: DC 3A
Balance Current: 0.4A/Cell X 2
Input Port: QC/PD/BC1.2/USB-C V1.4/SDP/CDP/DCP/Apple 5V/2.4A(Does not support 5V/1A adapter input)
Abnormal Battery Voltage Alarm: Yes
Supported Battery Types: Lipo/LiHv/LiFe(2~4S), NiMH(2-12S)
Working Temperature: 0℃~40℃
Storage Temperature: -20℃~60℃
Dimension: 85x55x21mm
Net Weight: Approx. 64g
Includes
1x GensAce IMARS Mini G-Tech 60W 5A DC Smart Charger
Taking your drone photography to the next level, the new series Cinebot30, take you to the real world, shooting extreme footage.
Cinebot30 is a new generation of Cinematic FPV drone developed by GEPRC team. The high-strength 7075 aircraft-grade aluminum alloy bracket for FPV camera escort, the combination of classic engineering and aesthetics. The newly polished gimbal damping module can easily fix high-frequency vibration and jello issues. It can be mounted with GEPRC Naked GoPro Hero 8 and GoPro Black Bones, Insta 360 GO2 and other cameras. The image is stable and clear, and it’s easy to film.
Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!
Cinebot30 will be equipped with a powerful 1804 motor with optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmx3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations. Finely polished frame design, only 6 screws need to be removed to separate the aircraft top plate and protection frame. Easy to cope with the urgent need to replace the accessories, at any time to restore the state.
Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Design that combines engineering and aesthetics.
Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts.
Selected high-toughness and impact-resistant PC material for injection molding.
Aviation 7075 aluminum alloy camera mounting bracket and fuselage aluminum column.
Propeller guard embedded ring Cob light strip, carefully tuned light effect. Color brightness in the day and night can be clearly displayed.
The newly developed gimbal shock absorption structure can disintegrate high frequency jitter and jello effect. Easily carry a variety of action cameras.
Powerful 1804 motor, surging torque to deal with ultra-low altitude flight at will.
With the new GEP-F722-45A AIO V2, stable performance, more secure flight
Four kinds of FPV system with the program, choose to belong to your first-person view
Tuned by GEPRC professionals, delicate and silky flying feel
Specifications
Input Voltage: 3-4S
Wheelbase:127mm
Isolation Plate:2mm
Main plate:3mm
Bottom plate:1.5mm
Motors: SPEEDX2 1804-3450KV
Propellor: HQ prop T76mmx3 propeller
VTX: GEPRC RAD 1W
Antenna: Peano 5.8G 110mm RHCP MMCX Antenna
Camera: Caddx ratel 2
Weight: 206.4g
GEPRC GEP-F722-45A AIO
Model: Cinebot30 HD Nebula PRO Quadcopter
Gyro: BMI270/42688 gyro/accelerometer(SPI)
OSD: Yes
ESC Connections: Yes
Firmware: GEP-F722-45A AIO
BEC: 5V 1A
Current Sensor: Yes
Buzzer: no
Barometer: No
Input Voltage: 2-4S LiPo
MCU: STM32F722RET6
IMU: ICM-42688-P
Stack Size: 25x25mm
Dimensions: 32x32xmm
Weight: 8.8g
Includes
1x GEPRC BNF CineBot30 4S 3" Analog Cinewhoop - Choose Version
2 x HQProp T76MM（pair）
1 x Battery strap M15x200mm
1 x Battery strap M15x220mm
2 x Battery Silicone Pads
1 x Set of screws
1 x Set of screwdrivers
1 x GoPro camera mount holder
1 x Set of screws
1 x Set of screwdrivers
1 x Antenna fixed tube
Since DJI released the O3 AIR Unit FPV high-definition video transmission system, the GEPRC team has followed closely to make the latest set of the O3 AIR Unit system, the Cinebot30 HD O3 AIR Unit version. The Cinebot 30 is a new generation of cinematic FPV drones developed by the GEPRC team.
The aluminum parts of the camera are still made of high-strength 7075 aircraft-grade aluminum alloy materials. The TPU shock-absorbing pad is designed on the bracket structure, which can excellently isolate the high-frequency vibration of the fuselage so that the camera can still obtain jelly-free high-definition images during high-speed flight The installation of the video transmission has also designed an assembly scheme, which allows the O3 video transmission to be completely installed inside the fuselage without affecting the Type-C USB data cable connected to the Air Unit to read video data. O3 Air Unit is currently the most advanced FPV system on the market. It can transmit 1080P 60fps real-time images, and can also record up to 4K 60fps images with an anti-shake effect at the same time.The upgraded video transmission system also combines market feedback to upgrade the gimbal top plate of the fuselage, which is compatible with the camera base fixed by 4-hole screws, so that Cinebot30 can mount a full-sized GoPro camera very well, and the battery life can reach 5 minutes and 30 seconds. However, the GEPRC team recommends flying with Naked GoPro 10, with a battery life of up to 10 minutes and 30 seconds.Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!Cinebot30 will be equipped with a powerful 1804 motor with an optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmX3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations.Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots!
Features
Adopts the most advanced O3 Air Unit FPV digital video transmission system on the market
Video transmission with high-definition anti-shake 4K 60fps ultra-high resolution video quality
The highest bit rate is 50MBPS, the delay is as low as 30 milliseconds, and the highest image quality is 1080P 60FPS
Upgraded the top plate of the fuselage gimbal, compatible with the camera base fixed by 4-hole screws, and supports mounting a full-sized GoPro camera for flight
The camera aluminum mechanism is designed with TPU shock absorption, which can effectively eliminate the image jello caused by the vibration of the body
The ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. Color brightness can be clearly displayed in day and night
Selection of high-quality high-toughness, impact-resistant PC&PET material injection molding
Powerful 1804 motor, surging torque to cope with ultra-low altitude flight
Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts
With the new GEP-F722-45A AIO V2, the performance is stable and the flight is more secure
Tuned by GEPRC professionals, delicate and silky flying feel
Specifications
Model: Cinebot30 HD O3 Quadcopter
Brand: GEPRC
Frame: GEP-CT30 O3
Wheelbase:127mm
Isolation Plate:2mm
Main plate:3mm
Bottom plate:1.5mm
FC: GEP-F722-45A AIO V2
MCU: STM32F722RET6
IMU: ICM-42688-P
VTX: DJI O3 Air Unit
Video resolution: 4K@50/60fps, 2.7K@50/60/100/120fps, 1080p@50/60/100/120fps
Camera: DJI O3
Propeller: HQ prop T76mmx3 propeller
Antenna: DJI O3 Antenna
Charge connector: XT60H-M
Motor: SPEEDX2 1804-2450KV（6S Version）/ SPEEDX2 1804-3450KV（4S Version）
Weight: Nebula Pro version 222.5g / Avatar version 221g / Analog version 209.2g / Link Wasp version 222.5g / O3 version 234.7g (excluding battery, the above are TBS Nano RX version)
Receiver: PNP, Frsky R-XSR, TBS Nano RX, ELRS 2.4G
Recommended Battery: LiPo 4S 1100mAh-1300mAh (4S Version) / LiPo 6S 850mAh-1100mAh(6S Version)
Includes
1x Cinebot30 HD O3 Quadcopter
2x HQProp T76MM（pair）
1x Battery strap M15x200mm
1x Battery strap M15x220mm
2x Battery Silicone Pads
1x Set of screws
1x Set of screwdrivers
1x GoPro camera mount holder
1x Set of screws
1x Set of screwdrivers
1x Antenna fixed tube
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market.
The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life.
It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras.
Find the recommended 4S 450-750mAh batteries here!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect.
Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning.
2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting.
SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried.
Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted.
The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible.
Specifications
Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz
Frame: GEP-CL20
Wheelbase: 100mm
Gimbal plate: 2.0mm
Top plate: 2.5mm
Bottom plate: 1.5mm
FC system: GEP-F411-35A AIO
MCU: STM32F411CEU6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 35A
VTX: GEPRC 5.8GHz@600mW
Camera: Caddx Ratel2
Antenna: GEPRC Peano 5.8G RHCP MMCX
Motor: GR1303.5 5500KV
Propeller: EMAX Avan Micro 2×2.4×4
Receiver: ELRS2.4G
Recommended battery: LiHv 4S 450mah-660mah
Flight time: 4-6min
Includes
1x CineLog20 Analog
2x 2-inch propellers (pairs)
1x Naked GoPro Base
2x M15×150mm battery strap
2x Battery Silicone Pads
2x EVA Landing Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x Antenna fixed tube
1x 4S Naked GoPro power cable (with balanced terminal head)
2x EVA damping rings of guards
1x TBS Antenna mount (Vertical Type)
1x TBS Antenna mount (Horizontal Type)
1x TBS Antenna printed parts
The screw package includes:
3x M2×12mm cup head screws
2x M2×5mm round head screws
1x M2×8mm round head screw with pad
3x M2×7mm round head screws
2x M2×8mm round head screws
2x M2 iron nuts
1x self-clinching nut
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog four mainstream video transmission systems on the market.
The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 AIR Unit shooting, which can achieve an excellent anti-shake effect. The O3 Air Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life.
It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras.
Find the recommended 4S 450-750mAh batteries here!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect.
Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning.
2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting.
SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried.
Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted.
The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible.
Specifications
Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz
Frame: GEP-CL20
Wheelbase: 100mm
Gimbal plate: 2.0mm
Top plate: 2.5mm
Bottom plate: 1.5mm
FC system: GEP-F411-35A AIO
MCU: STM32F411CEU6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 35A
VTX: Link
Camera: RunCam Wasp
Antenna: GEPRC Peano 5.8G LHCP U.FL
Motor: GR1303.5 5500KV
Propeller: EMAX Avan Micro 2×2.4×4
Receiver: PNP (built-in DJI receiver), ELRS2.4G
Recommended battery: LiHv 4S 450mah-660mah
Flight time: 4-6min
Includes
1x CineLog20 HD Wasp
2x 2-inch propellers (pairs)
1x Naked GoPro Base
2x M15×150mm battery strap
2x Battery Silicone Pads
2x EVA Landing Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x Antenna fixed tube
1x 4S Naked GoPro power cable (with balanced terminal head)
2x EVA damping rings of guards
1x TBS Antenna mount (Vertical Type)
1x TBS Antenna mount (Horizontal Type)
1x TBS Antenna printed parts
The screw package includes:
3x M2×12mm cup head screws
2x M2×5mm round head screws
1x M2×8mm round head screw with pad
3x M2×7mm round head screws
2x M2×8mm round head screws
2x M2 iron nuts
1x self-clinching nut
Does not come with naked Gopro mount. Please refer to the includes list at the bottom of the listing for all included items.
The classic CL25 Frame, designed by the GEPRC team, has been upgraded. They've redesigned the shock absorption structure of the camera mount, eliminated the jelly coming from the FPV camera, and you can now use 3, 4, and 5 damping rings according to the flight state to obtain the best stability in vibration and noise. The CL25 can be used for Vista HD digital image transmission system or Analog image transmission system. The center of gravity of the quadcopter is in the middle,
Check out all our DJI-compatible frames, electronics, and accessories as well as our whole GEPRC product line!
Specifications
Dimensions: 109mm
Frame Style: Cinewhoop
Top Plate: 2.5mm
Bottom Plate: 1.5mm
Bottom Plate(camera): 2mm
Stack Size: 26.5x26.5mm
Motor Mount: 9x9mm (compatible with 1105/1204/1206 motors)
Camera Mount: 14-20mm (Nano and Micro-sized)
Weight: 47.8g
Recommended:
Motor: BetaFPV 1404 4500Kv Micro Motor 4 Pack
FC/ESC: GEPRC F411 2-6S AIO Flight Controller w/ 35A 4in1 ESC
Prop: Gemfan D63 Ducted Durable Tri-Blade 2.5" Cinewhoop Prop 8 Pack
LiPo: RDQ Series 14.8V 4S 650mAh 80C LiPo Micro Battery
Includes
1x Top plate 2.5mm
1x Bottom plate 1.5mm
1x Bottom Plate (Camera)1.5mm
4x (M2x3.5x25mm) Aluminum posts
2x (M2x3.5x8mm) Aluminum posts
28x (M2x6mm) YFS Round head screws
2x (M2x8mm) YFS Round head screws
4x (M2x12mm) YFS countersunk head screws
16x (M2x2mm) Nylon Nuts
4x (M2x18mm) YFS countersunk head screws
5x Damping Rings
1x (19x19mm) Mount of camera
1x (14x14mm) Mount of camera
1x 3D print part of XM antenna
1x 3D print part of TBS antenna
1x Naked Camera Mount (This is just the base, NOT the actual camera case)
2x Batteries pads
2x EVA Landing pads
4x 2.5-inch Guards
1x EVA Damping Ring of Guard
2x Antenna Tubes
2x Batteries straps (M15x150mm）
The latest 3-inch frame from GEPRC, the CL30 is now officially released.
The CL30 has upgraded the design of the CL25 Cinelog25. It continues the 26.5×26.5mm FC hole position and 20x20mm image transmission hole position. It can be installed with mainstream FC AIOs, DJI Vista modules, and most of the analog VTXs on the market. The 9x9mm motor holes can be installed with 1404-1408 motors, and the power output is strong with 3-inch blades. GEP has improved the shock absorption design of the damping platform to provide a more stable shooting effect. Ultra-light body weight, this 3-inch can carry a GoPro Hero 8 naked camera or an Insta360 Go2 camera can be installed with GoPro camera mount.
GEPRC pursues lighter body weight, a better flying feel, and more extended functions.
Check out all our DJI-compatible frames, electronics, and accessories as well as our whole GEPRC product line!
Specifications
Dimensions: 180x180x38mm (Including the propeller guard）
Frame Style: Cinewhoop
Top plate: 2.0mm
Bottom plate: 2.0mm
Arm Thickness: 3.0mm
Stack Size: 26.5x26.5mm
Motor Mount: 9x9mm
Camera Mount: 14-19mm (Nano and Micro size)
Weight: 62.6g (Including the Prop Guard, and 3D Prints)
Recommendations:
Motor: GEPRC GR 1404 3850Kv Micro Motor
FC/ESC: GEPRC F411 2-6S AIO w/ 35A 4in1 ESC
Prop: HQ Prop T76MM Tri-Blade 3" Cinewhoop Prop 4 Pack
LiPo: RDQ Series 14.8V 4S 650mAh 80C LiPo Micro Battery
Includes
1x Top Plate 2.0mm
1x Arm Plate 3.0mm
1x bottom Plate 2.0mm
2x Knurled nut M2
4x Aluminum Column M2x3.5×25
2x M2x4mm cup head screws
28x M2x6.5mm round head screws
10x M2x8mm round head screws
7x M2x9mm round head screws
4x M2x10mm round head screws
1x M2x12mm cup head screw
4x M2x16mm cup head screws
1x M2 Rivet nut
4x M2 Lock nuts
8x M2 Iron nuts
8x M2 * 6.5mm damping rings
9x damping platform rings
1x 19x19mm Camera Mount
1x VTX Antenna Mount
1x TBS T-shaped Antenna Mount
1x TBS NanoRX Mount
1x Camera Protector
6x 3 in Propeller Guard
1x GoPro Camera Mount
4x EVA Damping Ring of Guards
2x 3M Double Tapes
2x Silicone Pads
2x Landing Pads
1x M15x200mm Battery Strap
1x M15x150mm Battery Strap
1x L-shaped (1.5mm)
Another solid pair of micro motors from GEPRC, perfect for those 3" builds.
Check out all our micro motors & all our GEPRC products!
Specifications
KV: 3850
Configuration: 9N12P
Stator Diamter：14mm
Stator Length：4mm
Shaft Diameter: 1.5mm
Motor Dimensions: Φ18.3 * 14.5mm
Weight: 9.8g
Idle current@8V(A) ≤0。51
No.of Cells(Lipo): 2~4S
Max Continuous Power(180S): 214
Internal Resistance: 0.213mΩ
Max Current(180S): 13.38A
Includes
1x GE PRC GR 1404 3850Kv Micro Motor
Introducing... the GEPRC SMART 16 Freestyle Frame Kit!
The GEPRC Smart 16 1.6" Nano Freestyle Frame is a tiny, lightweight freestyle FPV addition to the GEPRC Phantom series. The SMART 16 continues the consistent lightweight design concept of the Phantom series. The 1.5mm carbon fiber arm, with a 1mm top plate, creates a balance point that is maintained between the strength of the fuselage and the weight of the whole drone which allows it to be lightweight and tough at the same time. The M1.4 Motors mounting holes can be used to install small 3-hole brushless motors to reduce the weight of the body. Good arm width contributes to high durability. This design is great for freestyle flying, with no props in view!
Thanks to the 3D printed parts, the frame weighs only 8.5g, saving a lot of overall weight. The independent battery compartment is designed to stick the battery on top and below the drone making it very convenient and fast to replace batteries.
Check out our other Micro frames And our whole GEPRC product line!
Specifications
Frame Style: Toothpick
Top plate thickness: 1.0mm
Bottom plate thickness: 1.5mm
Camera plate thickness: 1.0mm
Stack Size 16x16mm
Motor Mount: 6mm Tri 08xx
Camera Mount: 14mm Nano
Weight: 8.5g (including 3D prints)
Recommended:
Motor: GEPRC SPEEDX2 0803 11000Kv Micro Motor
AIO: GEPRC F4 V1.4 2-4S AIO Flight Controller
Prop: HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack
LiPo: RDQ Series 350mah 2S 50C/100C 7.6V HV XT30 Micro Battery
Includes
1x GEPRC SMART 16 1.5mm Bottom Plate
2x GEPRC SMART 16 1mm Camera Plate
1x GEPRC SMART 16 1mm Top Plate
2x 120mm LiPo Strap
1x 3D Printed Part Set
1x Screwdriver Set
1x Hardware Set
2x Battery Pad
Introducing the GEPRC Taker F411 8bit 12A AIO Flight Controller, the perfect addition to your mini FPV drone. It is packed with features like ICM-42688-P gyro, 12A ESC support, 2-4S power, and a built-in black box with 16MB flash memory for easy parameter adjustments. Best of all, this AIO comes with a built-in ELRS 2.4GHz receiver with a U.FL connector. Get ready for smooth and precise races and freestyles with this highly-integrated powerful all-in-one flight controller!
Check out all our Whoop/AIO Flight Controllers, as well as the rest of our GEPRC selection.
Features
Bluejay 12A ESC, support 2-4S battery, continuous current 12A, peak current 13A, built-in ammeter
SPI ELRS 2.4G receiver
Using STM32F411 FC, the flight control is running stably
Using IMU: ICM42688P gyroscope, 8K sampling rate
Support buzzer and LED light function
With 25.5mm x 25.5mm mounting holes
Specifications
Model: TAKER F411 8Bit 12A AIO
MCU: STM32F411
IMU: ICM42688P
Firmware target: GEPRC_F411_SX1280
OSD: BetaFlight OSD w/ AT7456E chip
UART Ports: R1 T1\R2 T2
Reverse Port: NR2
Buzzer: YES
LED: YES
USB Port: Micro USB
ESC MCU: BB21F16G
Black Box: 16Mb onboard flash memory
Continuous Current: 12A
Peak Current: 13A
Input: 2-4S
ESC Protocol: Dshot300, Oneshot, Multishot
Current Meter: 210
ESC Firmware: G-H-30 – Bluejay, 0.16, 48kH
Size: 31.2 x 31.2mm Board
Mounting holes: 25.5mm x 25.5mm hole, M2 hole
Weight: 7g
ELRS Connector: U.FL
Includes
1x GEPRC Taker F411 2-4S AIO Whoop/Toothpick w/12A 8bit 4in1 ESC - ELRS 2.4GHz (SPI)
1x XT30-5.5CM-20AWG power cable
8x M2x6.5mm FC damping grommets (4 each in red/black)
1x 35V220UF capacitor
5x Self-tapping screws (M1.4X5)
1x Instruction manual
The Crux 35 is an ultra-lightweight 3.5Inch FPV freestyle and racing drone, the weight of the whole drone is only 87g for the analog version and 108g for the digital HD version. The Crux35 series drone use Happymodel's EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
Happymodel Crux35 Racing Drone V2 comes with the CrazyF411 ELRS flight controller. This board comes with an integrated UART 2.4GHz ExpressLRS receiver and 20A BLheli_S ESC(Bluejay firmware pre-installed) which could support 3-4S.
The new V2 version comes with CrazyF411 ELRS AIO flight controller built-in UART ExpressLRS receiver which allows for updating the receiver with ease.
Choose from between ELRS 2.4GHz and FrSky for your receiver.
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Features
Bind tutorial for ELRS
Ultra-lightweight 3.5-inch BNF FPV Freestyle Drone
HD video transmission and analog video transmission are optional
Integrated ExpressLRS UART receiver
High efficiency EX1404 power system
Can be equipped with Naked Gopro or SMO4K
Specifications
Weight: 87g
Brand: Happymodel
Wheelbase: 150mm
Dimensions: 130mmx130mmx45mm
Receiver option: UART ExpressLRS 2.4GHz
HappyModel Flight Controller (ELRS Version)
Input Voltage: 2-4S LiPo
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: BMI270 or ICM42688P (SPI control)
ESC Connections: Yes
Firmware: CrazybeeF4DX
Current Sensor: Yes
Mount pattern: 25.5x25.5mm (M2)
Dimensions: 32x28x9mm
Weight: 5g
Built-in 20A Blheli_s ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1A BEC
Onboard ESC:
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite and ESC-Configurator programmable
Factory firmware: Bluejay 0.18.1
Firmware target: F_H_40_48_v0.18.1
Support DSHOT150/DSHOT300/DSHOT600
Default protocol: DSHOT300
HappyModel EX1404 3500KV Motor
Mode: EX1404
Kv: 3500Kv
Input Voltage: 3-4S LiPo
Configuration: 9N12P
Motor Dimensions: Φ17.8mm x 17.6mm
Stator Dimensions: Φ14mm x 4mm
Shaft Diameter: 1.5mm
Mounting Pattern: Φ9mm
Weight: 9g
HappyModel Propellers
Propeller Diameter: 3.5 inch
Pitch : 2
Blades : 3
Material : Poly Carbonate
Weight : 1.5g
Hub Diameter : 10mm
Hub Thickness: 4.7mm
Shaft :1.9/1.5/1.9mm
Adaptor Rings : NO
Caddx Ant Camera
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC and PAL(switchable)
MENU: Support
IMAGE: 4:3 or 16:9
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio: >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm/F2.5
Minimum illumination: 0.001Lux
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14x14mm
Wide Power Input: DC 3.7-18V
Work Temperature: -20°C~+60C
Work Humidity: 20%~80%
Weight: 1.7g
Happymodel OVX303 5.8G analog VTX or OVX306 5.8G analog VTX
Input Voltage: 5V
RF Output Power: 25-300mW
Antenna Connector: U.Fl
Power/Video Connection: Solder Pads
OVX303 Stack Size: 16x16mm, 20x20mm, 25x25mm
OVX306 Stack Size: 25x25mm
Weight: 0.9~1g
Includes
1x HappyModel BNF Crux35 V2 3.5" Analog Quad - Choose version
1x 5D-OSD menu board
1x Screw Driver and Screw Set
8x HQProp T3.5X2X3Grey (4cw+4ccw)
1x Buckle Velcro for battery
Equip your 2-4S drone with the HappyModel CrazyF411 F4 Flight Controller. Enjoy flying with its 20A 8Bit 4in1 ESC and ELRS 2.4GHz receiver featuring a high-sensitivity SX1280 frequency chip for low latency, high packet rate, and great range. With a big Mosfet that supports up to 20A currents, this controller is perfect for FPV drones and strong enough for race or freestyle flying. This flight controller lets you update firmware through Betaflight pass-through or WIFI. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. The default firmware is ELRS V3.0.1. Get ready to take your drone game to the next level!
Browse the rest of our Whoop AIO Boards and our Happymodel gear.
Features
Integrated serial 2.4GHz ExpressLRS receiver
Pre-installed with Bluejay firmware)
Coming with a BMI270 gyro
Specifications
Flight Controller
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: ICM42688P
Mount pattern: 25.5x25.5 M2
Size: 32x28x9mm
Power supply: 2-4S Lipo battery
Built-in 20A Blheli_S ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1.5A BEC
Flight controller firmware target: CRAZYBEEF4DX
Weight: 4.97
Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay 0.18.1Firmware target: F_H_40_48_v0.18.1
Default protocol: DSHOT150/DSHOT300/DSHOT600
Onboard UART ExpressLRS 2.4GHz Receiver
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1
Onboard voltage and Amperage Meter Settings
Voltage meter scale setting 110
Amperage meter scale setting 470
Includes
1x HappyModel CrazyF411 F4 2-4S Whoop/Toothpick AIO Flight Controller w/ 20A 8Bit 4in1 ESC - ELRS 2.4GHz (UART)
2x Wire
1x Hardware Set
4x Grommets
Wiring Diagram & Binding Procedure
Binding procedure
Supply power to the flight controller by plug USB, wait until the green LED on the FC is off, immediately turn off the power, and then repeat again the above steps. When the FC is powered on for the third time, the green LED light will start to double-flash, which means that the RX enters the binding mode
Please make sure your ExpressLRS tx module firmware is v3.x.x. And go to ExpressLRS.lua from “TOOLS” menu of your radio transmitter. Then hit [Bind] to binding with the onboard ExpressLRS receiver. The green LED should blinking slowly first then turn to solid, that means binding was successfully. If the green led still keep double flash after binding ,please change Model Match tab value from “off” to “on” or from “on” to “off”
Receiver LED status meanings
Green LED solid means bind successful or RC link established; Green LED double-flash means get into bind mode; Green LED flash slowly means no RC signal input from TX module; Green LED continuous flash fast means ExpressLRS wifi enabled.
Bind successful
Bind Mode
No RC Input
Wifi Mode
HappyModel has been making micro motors for a long time, and their experience shows in this EX line of motors.
Check out our other 1404 motors, and all our HappyModel selection!
Specifications
Kv: 3500Kv
Input Voltage: 3-4S LiPo
Configuration: 9N12P
Motor Dimensions: Φ17.8mm x 17.6mm
Stator Dimensions: Φ14mm x 04mm
Shaft Diameter: 1.5mm
Mounting Pattern: Φ9mm
Weight: 8.7g
Available in CCW and CW
Includes
1x HappyModel EX1404 3500Kv Motor
Due to this item’s size or weight, it is not available for free shipping and may be shipped via ground.
This is a PNP wing, but assembly is still required.
Designed for FPV flying, the Heewing T1 Ranger PNP Twin Motor Wing is a great wing all around. Lightweight and portable, with a quick disassembly design, this build only takes minutes to put together and take apart. A small wingspan with large space for stress-free placement for your electronic equipment. And many other features to check out!
Check out all our PNP wings, Kit wings, and all out HeeWing products!
Features
Two-section hatch with ample room hatch for electronics
High-Quality EPP / Carbon FIber / Aluminum Materials
Supports External FPV Camera Mounting
730mm Fixed Wing Span
Quick Release Structure
Dual Motors
Specifications
Wingspan: 730mm
Length: 645mm
Hight: 140mm
Dimension: 660x225x135mm
Propeller recommend: 5-6 inch
Battery recommend : 4S 1300-2200mah
Battery: 2S~3S 1300mah~5000mah LiPo
Radio System: 2.4G 6CH
Material: EPP / ABS+PC / Carbon fiber / Aluminum
Includes
1x Heewing T1 Ranger PNP Twin-Motor Wing
Due to this item’s size or weight, it is not available for free shipping and may be shipped via ground.
This is a PNP wing, but assembly is still required.
Designed for FPV flying, the Heewing T1 Ranger PNP VTOL Twin Motor Wing is a great wing all around. Lightweight and portable, with a quick disassembly design, this build only takes minutes to put together and take apart. A small wingspan with large space for stress-free placement for your electronic equipment. And many other features to check out!
Important Note
T1 VTOL-PNP w/FC, Factory pre-installed. Save your time and enjoy to fly! Though regarding to the FC, it is pre-installed on the plane, but it is not fully tuned. It has flight control VTOL parameters for free, but this parameter is for reference only, and we do not take any responsibility or obligation for this parameter. It is strongly recommended that players must strictly adjust according to their actual flight environment and needs！
Check out all our PNP wings, Kit wings, and all our Hee Wing products!
Features
Two-section hatch with ample room hatch for electronics
High-Quality EPP / Carbon FIber / Aluminum Materials
Supports External FPV Camera Mounting
730mm Fixed Wing Span
Quick Release Structure
Dual Motors
FC Manual
Specifications
Wingspan: 730mm
Length: 645mm
Hight: 140mm
Dimension: 660x225x135mm
Propeller recommend: 5-6 inch
Battery recommend : 4S 1300-3500mAh
Radio System: 2.4G 6CH
Material: EPP / ABS+PC / Carbon fiber / Aluminum
Includes
1x Heewing PNP T1 Ranger VTOL Twin-Motor Wing - Grey - Choose Version
1x Fixed Wing Hardware Kit
The HobbyWing Skywalker 40A-V2 ESC offers superior performance for air applications with its 32-bit microprocessor running up to 96 MHz, DEO technology to improve throttle response and efficiency, and Normal/Reverse Brake Modes for reduced landing distance. An integrated search mode helps you find lost aircraft, making the Skywalker 40A V2 a reliable and powerful choice for RC enthusiasts.
Note: This ESC will not work with BLHeli_32 ESC Firmware
Make sure to check out the rest of our wing products and our entire line of HobbyWing gear!
Features:
High performance 32-bit microprocessor (with a running frequency of up to 96MHz)
DEO (Driving Efficiency Optimization) Technology that greatly improves throttle response driving efficiency and reduces ESC temperature.
Separate programming cable for connecting the ESC to a LED (program box - Sold Separately) that allows users to program the ESC anytime and anywhere.
Normal and Reverse brake modes that can effectively shorten the landing distance for the aircraft.
Search mode can help users find the aircraft by the alarm beeps after the aircraft falls into the complex environment.
Multiple protection features such as start-up, ESC thermal, capacitor thermal, over-current, over-load, abnormal input voltage and throttle signal the loss will effectively prolong the life of the ESC
Specifications
p/n: 80060022
Model: 40A V2
Refresh rate of the throttle signal: 50Hz to 432Hz.
Cont.Current: 40A
Peak.Current: 60A
Input Vol (Lipo): 3-4S
BEC Output: 5V @ 5A (Switch-mode)
Size (mm): 60 x 25 x 8mm
Weight(g): 36g
Wires input: 14AWG-100mm
Wires output: 16AWG-75mm
Output connectors: 3.5 Gold Connectors (Female)
Programming: Stick / LED program box
Firmware update: N/A
Weight: 36g
Extra Information
HWA80060022 Hobbywing Skywalker 40A V2 40Amp Brushless ESC - Manual
Skywalker V2.pdf
Includes
HobbyWing Skywalker 32Bit V2 3-4S Individual 40A ESC
All batteries must be shipped by a ground shipping method.
Introducing iFlight's Defender 25, a sub-250 drone featuring the DJI O3 Air Unit. At 249g weight, Defender 25 doesn't require registration in most countries. The compact and lightweight design also make it easy to carry and store. It will be your best travel buddy to redefine your FPV adventure. The built-in 2.5-inch propeller guards were designed to fly boldly. You’ll experience a completely new creative freedom to fly whenever and wherever. The durable injection molded frame not only prevents damage to your motors or propellers but also protects the environment from small flight errors.
Equipped with the latest tech from DJI, the O3 Air Unit HD transmission system, the Defender 25 supports 4K video and shoots up to 155° super-wide FOV footage for stunning visuals. In addition, D-Cinelike color mode provides more creative freedom for color grading, allowing you to edit and adjust your footage.
They’ve also added a special vibration-damped camera mount to keep your raw footage as smooth as possible, as well as ensure good Gyro Data for the built-in or in-post camera stabilization.
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Features
Optimized Landing Gear for Take-Off in Complex Environments
Built-in High-Performance video and Receiver Antennas
4K Stabilized Video with 155° Ultra-Wide Angle
Crash-Protected Quick-Release Battery
Countless Easy-to-Use Features
Ultralight and Free to Fly
Small and Mighty
Specifications
Defender 25
Product Name: Defender 25 4S HD
Flight Electronics: BLITZ D25 F7 AIO
Video Transmission: DJI O3 Air Unit
Frame: 112±2mm
Motor: Defender25 1404
Prop: Defender25 2525 props (2.5-inch)
Weight of the Aircraft: 180g
Takeoff Weight incl. 550mAh battery: ≤249g
Dimensions (L×W×H)：158x155x69mm
Max Ascent Speed: 6 m/s (Normal Mode, Sport Mode)
Max Descent Speed: 6 m/s (Normal Mode, Sport Mode)
Max Speed: 100Km/H (Manual Mode)
Maximum Takeoff Altitude: 200 m
Max Hover Time: Approx. 6 mins (with 550mAh battery), 10mins (with 900mAh battery)
Max Flight Distance: 2-3 km
Max Wind Speed Resistance: 80 Km/H (Level 5)
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Transmission Power (EIRP): FCC: < 33 dBm / CE: < 14 dBm / SRRC: < 30 dBm
Antennas: Dual Antennas
GNSS: N/A
Video Transmission
Product Name: DJI O3 Air Unit
Weight: Approx. 36.4grams
Dimensions (L×W×H): L16.7×W103.9×H 81.3mm
Screen Size (single screen): 0.49-inch
Resolution (single screen): 1920×1080
Refresh Rate: Up to 100 Hz
Interpupillary Distance Range: 56-72 mm
Diopter Adjustment Range: -8.0 D to +2.0 D
FOV (single screen): 51°
Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz
Transmission Power (EIRP):
2.4 GHz: < 30 dBm (FCC), < 20 dBm (CE/SRRC/KC)
5.8 GHz [4]: < 30 dBm (FCC), < 23 dBm (SRRC), < 14 dBm (CE/KC)
Max Video Transmission Bitrate: 50 Mbps
Operating Temperature Range: 0° to 40° C (32° to 104° F)
Power Input: 7-9 V (1.5 A)
Recommended (Not Included)
iFlight Defender 25 Battery - 900mAh
Includes
1x iFlight BNF Defender 25 HD 4S 2.5" Cinewhoop w/ DJI O3 Air Unit and DJI Camera (Pre-Built, Tuned, and Tested)
1x Defender 25 550mAh Battery
1x Charging Adapter Board
2x Defender 25 2525 Props (pairs)
After our very popular 3-inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.
Our all-new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here.
ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all-new 2205 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to its 3inch predecessor which gives a lot more room for a lot more fun. Our GPS-measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch-outs or light freestyle moves.
A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).
Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products!
Note: Battery, GoPro, and GoPro mount are NOT included.
Check out our other pre-built quads, as well as the rest of our iFlight selection!
Features
High-performance True-AIO Board Beast Whoop F7 AIO 55A v2.0 to save weight and space
T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
Low Resonance frame construction (Less Jello, more Cinematic footage)
Pre-tuned with smooth freestyle settings
Butter smooth 2205 3200KV (4S)
ProTek35 Prop Guards V2.0
No Props or frame in view!
Pre-Tuned & Pre-Setup:
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning were applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, and activate Acro-Mode"
Specifications
Beast F7 V2 AIO FC
MCU: BGA-STM32F745
Gyro: BMI270
Blackbox: 8Mb Onboard Flash
BEC output: 5V 2.5A
Barometer: BMP280
Connector: Micro-USB
OSD: AT7456E
FC Firmware：IFLIGHT_F745_AIO_V2
Mounting pattern: 25.5x25.5mm φ3mm
Dimensions: 32.5x32.5mm
Weight: 8.5g
F7 55A 2-6S ESC
Current Sensor: Yes
Input: 2-6S LIPO
Current scale: 200
Constant: 55A
BLHeli: BLHeli-S
Telemetry: no
ESC Firmware: BlheliS G-H-30
Mounting pattern: 25.5x25.5mm/Φ3mm
Dimensions: 32.5x32.5mm
SucceX Mini Force 5.8GHz 600mW VTX
Power: PIT/25/200/400mW/600mW
Antenna interface: MMCX
VTX protocol: IRC Tramp
Output 40 channels.
Size: 29x29mm
Mounting pattern: 20x20Φ3/25x25 mmΦ2
Weight: 4g
Includes
1x ProTek35 Frame
2x Albatross RHCP RP-SMA 5.8g antenna
1x TPU Antenna holder
2x Nazgul 3535 propeller (Set of 4 - Color May Vary)
1x iFlight Lipo Strap 15x150mm (Color May Vary)
1x iFlight Lipo Strap 15x250mm (Color May Vary)
1x GoPro TPU bottom stand black (GoPro Protector not included)
All batteries must be shipped by a ground shipping method.This Battery only charges with the included Defender 25 Charger Adapter board.
Grab an additional battery or two for your iFlight Defender 25 and keep the fun going! With 6 minutes of flight time, you're sure to capture some amazing shots!
These batteries only work with the Defender 25 drone.
Specifications
Capacity: 550mAh
Cell Combination: 4S1P
Discharge rate: 60C
Weight: 70±2g
Size: 105x35x31.5mm±2mm
Battery type: LiPo
Connector: XT30
Cable Length: 32.5±1mm
Includes
1x iFlight Defender 25 4S 550mAh Battery
An awesome little AIO from iFlight, Coming with 20A ESCs, DJI ready header for an air unit or Caddx Vista, and a nice open pad layout to get all your peripherals on board!
Browse our Stacks & Combos, and our iFlight gear!
Features
Support 2-4S battery, new upgraded UARTS ports
F411 chip is used with high-performance computing speed, making it smoother during flight.
Specifications
Whoop AIO F4 V1.1 AIO
Size：30.5x30.5mm
Mounting pattern：25.5x25.5mm/φ3mm
Weight: 7.5g
MCU：STM32F411
Gyro：BMI270
Blackbox：8MB
BEC output: 5V 2A
Config：IFLIGHT_F411_PRO.config
INA pad：nR2
Barometer：No
Constant current: 20
Burst Current: 25A
Input：2-4S
Current sensor：yes
BLHeli：BLHeli-S
ESC Telemetry：no
Firmware Target：IFLIGHT_F411_PRO
ESC Firmware: Bluejay Q-H-50
Includes
1x Whoop AIO F4 V1.1 AIO Board× 1
1x Capacitor UPL 35V 470UF × 1
1x XT30 18awg cable
1x Wire harness (plug&play) for DJI Air Unit × 1
4x M2 silicon grommets × 4
4x M2 damping balls x 4
4x M2x8mm Screws x 4
Power your GoPro with your craft's LiPo, with this Type C to Balance Head Charging Cable for GoPro Hero 6/7/8!
Check out the Rest of our iFlight product range and PDB/BEC selection while you're at it!
Features
High Comparability: Compatible with GoPro Hero 6/7/8
High quality and fast charging.
Specifications
Model: Type-C 90 degree to balance plug
Product Weight: 5.5g
Support: 4S-6S
Output: 5V/3A
Input Connector: XH2.54
Output connector: 90°Type-C
Length: 110mm
Includes
1x Type C to Balance head Charging Cable
A relatively large motor for a 12x12mm, M2 mounting pattern. This motor is ideal for lightweight 5" builds.
Check out all our Micro Motors and our selection of iFlight gear!
Features
High-strength 5mm Steel shaft
Japanese NSK φ8*φ3*4 bearings
N52H curved magnets
Motor wires protected
Dynamically balanced
Specifications
KV: 2300KV
Input Voltage: 4S/6S Lipo
Configuration: 12N14P
Stator Diameter: 22mm
Stator Length: 5mm
Bottom Mounting pattern: 12*12mm/M2
Weight: 25.5g with short wire
Includes
1x iFlight Xing 2205 2300Kv Micro Motor
iFlight XING provides the most incredible power and thrust in the lightest weight. iFlight continues the tradition of making the best and most suitable products to offer different size and KV value to meet different pilots’ needs. It means that the iFlight XING series motor can be pushed to the limit. The sturdy structure and high-quality materials make iFlight XING perform like a beast.
Check out our other 2306 motors, and all our iFlight selection!
Specifications
Kv: 2450Kv
Input Voltage: 2-4S LiPo
Configuration: 12N14P
Max Continuous Current: 44.57A
Internal Resistance: 47.3mΩ
Motor Dimensions: Φ13.5mm x 18.7mm
Stator Dimensions: Φ23mm x 06mm
Shaft Diameter: 5mm
Mounting Pattern: Φ16mm
Weight: 33.4g
Includes
1x iFlight Xing 2306 2450Kv Motor
XING-E PRO series are everything you love about Xing motors at a more affordable price, and now with a unibell design like their premium counterparts! Performance and durability are still of utmost importance to iFlight when designing these motors. They feature a 4mm high strength hollow steel shaft, single strand windings, M3 shaft screw, and larger 9x4x4mm NSK bearings.
We also carry the original Xing and Xing Camo lineup of course!
Check out our vast motor selection, and all our iFlight gear!
Features
New Unibell construction
High-strength 4mm Steel shaft
N52H High-temperature magnets, NSK bearings
16x16mm hole pattern
Single strand copper winding
Hex bolt shaft set screw
Specifications
Kv: 2450
Input Voltage: 2-4S
Configuration: 12N14P
Magnets: N52SH Curved
Max Continuous Current: 42.63A
Internal Resistance: 46.8mΩ
ldle Current@10V: 2A
Motor Dimensions: Φ28.5x19.7mm
Stator Dimensions: Φ22x7mm
Shaft Diameter: 4mm Steel
Bearing Dimensions: 9x4x4mm
Output Shaft Dimensions: ΦM5x15mm
Wire Dimensions: 20AWG x 150mm
Mounting Pattern: Φ16mm, 4x M3
Weight (w/ wires): 33.8g
Includes
1x IFlight Xing-E PRO 2207 2450Kv Motor
XING-E PRO series are everything you love about Xing motors at a more affordable price, and now with a unibell design like their premium counterparts! Performance and durability are still of utmost importance to iFlight when designing these motors. They feature a 4mm high strength hollow steel shaft, single strand windings, M3 shaft screw, and larger 9x4x4mm NSK bearings.
We also carry the original Xing and Xing Camo lineup of course!
Check out our vast motor selection, and all our iFlight gear!
Features
New Unibell construction
High-strength 4mm Steel shaft
N52H High-temperature magnets, NSK bearings
16x16mm hole pattern
Single strand copper winding
Hex bolt shaft set screw
Specifications
Kv: 2750
Input Voltage: 2-4S
Configuration: 12N14P
Magnets: N52SH Curved
Max Continuous Current: 42.63A
Internal Resistance: 46.8mΩ
ldle Current@10V: 2A
Motor Dimensions: Φ28.5x19.7mm
Stator Dimensions: Φ22x7mm
Shaft Diameter: 4mm Steel
Bearing Dimensions: 9x4x4mm
Output Shaft Dimensions: ΦM5x15mm
Wire Dimensions: 20AWG x 150mm
Mounting Pattern: Φ16mm, 4x M3
Weight (w/ wires): 33.8g
Includes
1x IFlight Xing-E PRO 2207 2750Kv Motor
iFlight's 2nd gen Xing lineup has raised the bar when it comes to FPV motors. The high manufacturing standards and premium performance offered by the Xing line have been improved upon, offering upgrades such as center slotted curved arc magnets, tighter gaps between magnet and stator, higher power output, and improved efficiency.
Available in multiple Kv options!
Check out all our Micro Motors and our selection of iFlight gear!
Specifications
Voltage: 2S-4S
KV Option: 4600Kv
Configuration: 9N12P
Stator Diameter: 14mm
Stator Length: 4mm
Shaft Diameter: 1.5mm
No.of Cells(Lipo): 2-4S
Internal resistance: 0.28Ω
Mounting pattern: 9*9-φ2mm
Bearing: 5*2*2.5mm
Wire: 120mm/26AWG
Weight: 8.5g (without cable)
Includes
1x iFlight Xing 2 1404 4600Kv Micro Motor
iFlight's 2nd gen Xing lineup has raised the bar when it comes to FPV motors. The high manufacturing standards and premium performance offered by the Xing line have been improved upon, offering upgrades such as center slotted curved arc magnets, tighter gaps between magnet and stator, higher power output, and improved efficiency.
Check out our vast motor selection, and all our iFlight gear!
Features
5mm titanium alloy shaft, our strongest prop shaft ever!
Crash resistant 7075 aluminum bell
Smooth and long-lasting NSK 9x9x4 bearings
Center slotted N52H curved arc magnets
XING O-ring bearing gap protection
Motor wires protector
Dynamically balanced
Specifications
Kv: 1855Kv
Version: CW Screw Thread
Input Voltage: 4S Lipo
Configuration: 12N14P
Stator Diameter: 22mm
Stator Length: 7mm
Wire length: 20AWG 160mm
Mounting pattern: 16*16mm
Weight: 31.6g with short wire
Includes
1x iFlight Xing 2 2207 1855Kv Motor
iFlight's 2nd gen Xing lineup has raised the bar when it comes to FPV motors. The high manufacturing standards and premium performance offered by the Xing line have been improved upon, offering upgrades such as center slotted curved arc magnets, tighter gaps between magnet and stator, higher power output, and improved efficiency.
Check out our vast motor selection, and all our iFlight gear!
Features
5mm titanium alloy shaft, our strongest prop shaft ever!
Crash resistant 7075 aluminum bell
Smooth and long-lasting NSK 9x9x4 bearings
Center slotted N52H curved arc magnets
XING O-ring bearing gap protection
Motor wires protector
Dynamically balanced
Specification
KV: 2555Kv
Version: CW Screw Thread
Input Voltage: 4S Lipo
Configuration: 12N14P
Stator Diameter: 23mm
Stator Length: 6mm
Wire length: 20AWG 160mm
Mounting pattern: 16*16mm
Weight: 31.6g with short wire
Includes
1x iFlight Xing 2 2306 2555Kv Motor
The PD60 has an XT60 charge port.
This ISDT charger takes an input voltage from USB-C, making it extremely convenient to use on the go.
Check out all our chargers & charging accessories, as well as our ISDT selection!
Features
USB-C power input
Upgradeable firmware
Silent Heat Dissipation
Supports 1-4S charging
Specifications
Input voltage: DC 5V-20V
Output voltage: DC 1.0V-20V
Max Input Current: 3A
Charging Current: 1A/2A/3A/6A
Max Charging Power: 60W
Balance Current: 0.5A/Cell Max
Support Quick-Charge: PD2.0/3.0,QC 2.0/3.0 ( 5V/1A input not supported)
Support Battery Types and Cell Count: LiFe, LiHV 1-4S, LiPo 1-4S, NIMH, Cd 1-12S
Abnormal Voltage Alarm: Support
Incorrect Cell Count Setting Alarm: Support
Working temperature: 0-40°C
Storage temperature: -20-60°C
Dimension: 56x85x21mm
Weight: 87g
Includes
1x ISDT PD60 60W 6A 2-4S DC Charger w/ USB-C Input
Custom designed with 20mm extra velcro hook, Luma Quads 250mm Battery Strap V3 with Metal Buckle offers a secure grip on your packs. Perfect for both small 850mah 4s on 3" or 4" quads, or larger 1300mah packs on larger frames. Friendly, approachable and straight-forward, Luma Quads helps you power up with ease!
Check out the rest of our battery straps as well as our Luma Quads Products!
Feature
Luma all-over design with silver metal loop in 250-230x16mm.
Includes
1x Luma Quads 250mm Battery Strap V3 w/ Metal Buckle (4pc)
The Luma 25 Frame Kit from Luma Quads is designed for Naked GoPro applications. This modern-designed frame features symmetrical top and bottom plates, where you can be built as a pusher or puller quad. You'll love how light and easy to assemble this kit is, at only 240.5g with a Naked GoPro, Vista, and a 450mah 4S pack, or 208g with an Air unit O3 and no GoPro! A solid frame for those looking to create a 2.5" Cinewhoop! This version comes with black ducts and blue tpu.
Check out our selection of micro frames as well as our Luma Quads Products!
Features
Symmetrically designed to be built in either Standard or Pusher configurations.
O3 Air Unit, Mini, Micro and Nano FPV camera options included.
HD Vista/Air Unit 03 / Analog compatible.
Slammed 15mm stack height.
Sub 250g AUW (inc Naked GP and 4S 450mah).
Support for 2.5" propellers.
Front Standard GoPro mount (suits any GoPro style camera mount)
Download the 3D model .stl files for this kit here.
Kit includes DJI Air Unit O3 Mounts
Specifications
Stack Mounting: 20x20mm and 25.5x25.5mm
Rear Mounting: 20x20mm and 25.5x25.5mm
Motor Mount Pattern: 9x9mm
Top Plate Thickness: 2mm
Bottom Plate Thickness: 2mm
Motor to Motor: 129mm
Frame Weight: 62g
Includes
1x Luma Quads Luma 25 Cinewhoop 2.5" Micro Frame Kit
LUMA 25 FRAME ASSEMBLY GUIDE. V1.0
Kit contents:
HARDWARE BAG BREAKDOWN:
Bag A - MAIN
Quantity
M2 8mm Bolt
4x
M2 15mm Standoff
4x
Bag B - STACK
M2 14mm Bolt
4x
M2 Plastic Nut
4x
Bag C - REAR STACK
M2 20mm Bolt
4x
M2 Steel Nut
4x
Bag D - MOTORS
M2 6mm
16x
Bag E - HD MOUNT
M2 8mm Bolt
5x
M2 Steel Nut
5x
M2 Steel Washer
5x
M3 16mm Bolt
1x
M3 Steel Nut
1x
M3 Steel Washer
4x
CARBON PARTS.
2mm Top-plate
1x
2.5mm Bottom-plate
1x
3D PRINTED PARTS.
Front FPV Camera mounts
2x
Front GoPro Hard-mount
1x
Rear Immortal T & Vista Antenna Mount
1x
25.5x25.5 Stack RX Mount
1x
Rear 20x20 Analog RX/VTX Mount
Plastic Parts.
2.5" Prop Guards
5x
Extras.
Zipties
4x
130mm x 12mm Battery strap.
1x
Assembly guide.
The Luma 25 is designed to be built in either Standard or Pusher configuration.
The following guide is for Standard configuration, if you want to build the Luma 25 as a Pusher the two carbon plates as well as the guards need to be flipped upside down and you attach the HD mount to the Bottom plate and the standoffs to the Top plate instead.
1) HD Mount
Insert 1x M3 Steel washer into the GPLite mount as shown.
Insert 2x Washers into the HD Cam Mount.
Align GPLite mount up with HD Mount, Insert M3 Nut into HD Mount.
Insert M3 16mm Bolt through M3 washer into HD Mount and secure with M3 nut.
Insert 4x M2 8mm Bolts through 4x M2 Washers.
Insert M2 Bolts and Washers through HD Cam Mount.
Install HD mount assembly onto Top Plate.
Secure HD Mount to Top plate using 4x M2 Steel nuts.
2) Main Frame.
Insert 4x 14mm M2 standoffs into TPU Front camera and Rear antenna mount.
Align with bottom plate.
Insert 8x 8mm Bolts through the Top and Bottom plates into the standoffs.
3) Prop Guards
Align and orientate the prop guards as shown.
Secure using the included 6mm Motor screws through the bottom plate through the guard into the base of the motor.
4) Rear AntennaSecure the Immortal T antenna Into the rear mount using zipties.
5) Other
The included 25.5x25,5mm or 20x20mm RX mounts can be used either on top of main stack to secure an RX if using Vista or in the rear 20x20mm stack mount position for rear mounted Analog VTX/RX.
IMPORTANT:Do not let electrical components come in contact with the carbon, use spacers that came with your with FC stack and the included RX/VTX Mounts to space your components away from carbon.
Another feature rich offering from Matek in the 30x30 class. Loaded with features for digital and analog builds. Matek leads the pack when it comes to quality and performance.
Check out our 30x30 Flight Controllers as well as the entire Matek selection!
Features
STM32F405 has 1MB flash which can run ArduPilot/INAV/BetaFlight
InvenSense the 3rd generation IMU ICM42688-P
9-60V(3~12S LiPo) wide input voltage and voltage sense. and a 9~16V BEC for DJI OSD or analog VTX
8motors+3servos in INAV/BF multirotor mixer.
SH1.0_8pin connector for PnP with 2x 4in1 ESC
SH1.0_6pin connector for PnP with HD System(Caddx Vista & Air Unit)
USB pin breakout for connecting to external USB adapter
Specifications
Input Voltage: 3-12S
MCU: STM32F405RGT6
IMU: ICM42688-P
OSD: AT7456E, DJI OSD
Barometer: SPL06-001 (I2C)
Blackbox: 16M-byte Flash memory
UARTs: 6 + 1x Softserial_Tx option
PWM outputs: 12 (8x Dshot)
I2C: Yes
BEC: 5V 1.5A, Vx, 9~16V/1~2A (3S IN/9V 2A, 4S IN/12V 2A, 6S IN/16V 2A, 8S IN/16V 1.5A, 12S IN/16V 1A)
ADC: 4 (VBAT, Current, RSSI, Airspeed)
PINIO: Yes
Dual Analog Camera Cignal Switchable: Yes
Mounting Pattern: 30x30mm
Dimensions 36x36x5mm
Weight: 7g
Includes
1x Matek F405-HDTE Flight Controller
6x Silicon grommets M4 to M3
1x SH1.0_8pin cable 5cm, 2x SH1.0_8pin connectors
1x SH1.0_6pin to GH1.25_8pin cable 8cm for HD System(Caddx Vista & Air Unit)
Wiring Diagram
The NewBeeDrone & Joshua Bardwell Smart Power Goggle Cable is a collaboration product between NewBeeDrone and Joshua Bardwell.
Back in Mid 2021, Joshua Bardwell contacted us and brought up the idea of a smart goggle power cable adaptor. We realized that we could make a device to power a goggle through leftover 4S/6S batteries from quads since even if the battery level is at 30%, it still has enough power to supply the goggle.
At first, we thought of just making a very simple power module board that takes 2S-6S batteries and connect it with a 5.5x2.1 DC male plug and use a heat shrink to cover it. However, that method seems too unreliable so we decided to put a power indicator LED light and a buzzer to indicate the number of battery cells when you plug in a battery. The aluminum case acts like a shield to protect the hardware while providing heat dissipation for the power module.
Why do we call it the Smart Power Module? Because it can automatically detect input voltage to indicate battery cell and will output voltage based on the battery voltage. If the battery voltage is too low, it will give a low voltage to trigger the "goggle low voltage" warning.
-Kelvin
Check out all our NewBeeDrone products!
Specifications
Power input port: XT60
Power input support: 3S/4S/6S battery
Calbe Length: 1.5 meters/4.92ft
LED power indicator light
Buzzer indicator: Beep per cell when the battery plugs in. The module will beep 6 times when a 6S battery is plugged in.
Voltage Output: 6.2V - 8.7V (Based on the battery average cell voltage)
Maximum Current: 2A
Includes
1x NewBeeDrone & Joshua Bardwell Smart Power Goggle Cable
Premium Controller with Quality Parts and FeaturesFeaturing F4 Processor and 45Amp BLheli32 with NewBeeDrone Smoov-certified hardware design that supports up to 3-6S batteries to provide the best and most reliable quality and performance for either freestyle or racing.
Designed to support the DJI Air Unit.Though DJI Air Unit can only support up to 4S, the Infinity300 Stack can make the DJI Air Unite compatible with 6S batteries by providing a 9V 16W clean power for the DJI Air Unit.
Plug-and-Play. No need to solder tiny wires.The Infinity300 Stack includes a bundle of wires to connect the Flight Controller and ESC and a bundle of wires to connect the Flight Controller to the DJI Air Unit. No need to solder any tiny wires, making it simple and clean to build.
Check out our other flight Controllers and all our NewBeeDrone products!
Specifications
MCU: STM32F405 CPUE @ 168mhz, can be overclocked
IMU: MPU6000
OSD: Betaflight OSD w/ AT7456Ev
UART Ports: 6 UARTS
USB: Micro USB
Input: 3-6S
Installing Hole: 30x30mm M3
Weight: 14g
Includes
1x NewBeeDrone Infinity305 F4 3-6S Flight Controller
4x Grommets short 4x Grommets Long
1x Infinity305 FC to DJI Air module cable 40mm
1x Infinity305 FC to DJI Air module cable 100mm
1x Infinity305 FC to DJI Air module cable 150mm
Wiring Diagram
Ring Magnets for an FPV drone? Yes! Team NewBeeDrone put in countless hours to figure out how they could improve upon the Smoov-Certified freestyle motor which provides super smooth performance for freestyle and cinematic FPV while maintaining the durability and precision machining you've come to expect from NewBeeDrone. NBD are proud to say that we have done just that... again!The 2306.5 Smoov V2 ring magnet motor has not only improved upon our very successful V1 motor, it is now 3 grams lighter! It's constructed with 7075 aluminum alloy unibell design for the best structural rigidity and comes with fully molded ring-style magnets.
Ring motors are also easier to clean than traditional motors. Unlike traditional square magnet motors, the Smoov ring magnets have no physical spacing between the magnets to allow for quick and easy removal of dirt, grime, or anything you can manage to get into them.Making a fully molded ring magnet with high magnetic flux density is at the heart of the design. NBD has developed a ring magnet that can hold up to N48SH levels! Ring magnets are typically used in camera gimbals because they need to operate silky smooth. Traditional gimbal motors are super smooth but they lack punch and power. The Smoov V2 motors have both, along with improved balancing and better performance. The Smoov V2 ring magnet motors have more punch, less weight, higher strength, and they're Smoover than ever!
This motor is also available in 1750Kv!
Check out our vast brushless motors selection, and all our NewBeeDrone products!
Features
Single-winding with 0.15mm lamination stator.
Ring Magnet N48SH NdFeB V2
Super Smoov performance for freestyle and cinematic purpose
Japanese NSK Bearing
7075 Aluminum
6" prop compatible with Motor Limit Settings in BetaFlight
Specifications
Input Voltage: 4S
Stator Diameter: 23mm
Stator Height: 6.5mm
Shaft Diameter: 5mm
Motor Dimension (Dia.*Len): Ø29.4mm*31.6mm
Weight: 36g(include cable)
Wire Size: 20AWG 150mm
Bearing: NSK/NMB 684ZZ Ø9×Ø4×L4mm
Includes
1x NewBeeDrone Smoov 2306.5 2450Kv Motor
1x Hardware Pack
PBTPBB8A80C4S2P, Pit Bull Tires Pure Gold 4S 80C Softcase LiPo Battery (14.8V/8000mAh) w/Battery Life Indicator & EC5 Connector
The Pit Bull RC Pure Gold 4S 80C Softcase LiPo Battery with Battery Life Indicator has been made for extreme performance in any RC from a scale truck to bashing. Pure Gold batteries are built to take abuse, while a built in LED indicator has been placed on the front of each battery to allow easy power status updates! This battery uses an EC5 connector and includes a T-style connector to allow compatibility with multiple applications.
Features:
Battery Life Indicator allows fast identification of battery power status
EC5 battery connector
T-style battery plug included
NOTE: This battery should always be balance charged when preparing for use and storage charged before storing. Specifications:
Capacity: 8000mAh
Voltage: 14.8V (4S)
This product was added to our catalog on July 26, 2022
PHB4S520050LCGEC5, Powerhobby 4s 14.8v 5200mah 50c Lipo Battery w EC5 Plug Hard Case LCG
POWERHOBBY 4S 14.8V 5200MAH 50C LIPO BATTERY W EC5 PLUG HARD CASE LCG
50C Continuous / 100C Brust
Perfect for 1/10 & 1/8 scale vehicles, Boats, Planes, Drones. When you want a powerful battery pack that you can depend on even when you push it to its limits, this 4s 5200mah 50C LiPo Battery is for you. Powerhobby Power Pro Series lipo batteries offers very high power and very long run time for your RC models. The 100C burst rate enhances your driving experience no matter what type of driving you are into.These batteries packs are made with superior Lithium Polymer raw materials. The advanced stacking technology enables a single cell of capacity to reach 5200mah. Powerhobby Power Pro Batteries are your ideal choice for your RC Applications
Application(s): 1/10 / 1/8 scale cars, trucks, and buggies, DronesDischarge Connector: ec5Balance Connector: JST-XHLenth : 138mmWidth :47mmHeight:38mmWeight: 16.5 Ounces
Includes : 1 Battery
Warranty:
This LiPo Battery Pack is guaranteed, under warranty, against defects in materials and workmanship upto 6 Months from the day of purchase•This warranty does not cover physical damage to the battery pack as the result of a crash, hard landing, impropermounting or any deformity caused by the user.•This warranty does not cover internal damage to the battery pack due to overcharging, deep discharging, or excessivedischarge current.
This product was added to our catalog on July 25, 2024
PHB4S6000100CEC5, PowerHobby 4S 14.8V 6000mAh 100C LiPo Battery with EC5, Hard Case
When you want a powerful battery pack that you can depend on even when you push it to its limits, this 4S 6000mah 100C LiPo Battery is for you. Powerhobby Power Pro Series LiPo batteries offers very high power and very long run time for your RC models. The 200C burst rate enhances your driving experience no matter what type of driving you are into. These batteries packs are made with superior Lithium Polymer raw materials. The advanced stacking technology enables a single cell of capacity to reach 6000mah. Powerhobby Power Pro Batteries are your ideal choice for your RC Applications.
Includes: 1 Battery
Features:
1/10 / 1/8 scale cars, trucks, and buggies, Drones
EC5
JST-XH
Length : 138mm
Width : 47mm
Height: 48mm
Weight: 20.5 Ounces
This product was added to our catalog on October 14, 2021
4S 14.8V 8000MAH 100C Lipo Battery, w/ Genuine Traxxas Plug, for X-Maxx 8S
Specially Designed for the Traxxas X-Maxx 8S.
Features a huge capacity for extended run times and a gigantic C rating so you'll have all the power you'll ever need.
Features:
Suggested Charge Rate: 3C
Continuous Discharge: 100C
Max Burst Rate: 200C
Voltage Output: 14.8
Specifications:
Length : 168mm
Width : 44.5mm
Height : 41.5mm
Weight : 23.2OZ
This product was added to our catalog on October 14, 2021
