PTK-5326, ProTek RC 2S Charge/Balance Adapter (4mm to 5mm Bullet Connectors)
This is a heavy duty 2S hard case lithium polymer battery charge/balance adapter lead from ProTek R/C. This 13" long charge lead allows you to plug a 2S battery with 5mm female bullet connectors directly to your charger, eliminating the need for a balance board!
This adapter lead features 4mm banana plugs on the charger end, and 5mm banana plugs on the battery end, connected with 14awg wire. The balance wires include a 2mm banana plug on the battery end, with a 7-pin XH plug connected with 22awg wire for balancing that is plugged directly into the 6S balance port in the charger.
This charge lead is specifically designed to connect a ProTek R/C 2S LiPo hard pack with 5mm connectors to ProTek R/C chargers, but will also work with any charger that uses 4mm bullet connectors for output, and has a 7-pin (6S) XH balance port.
This product was added to our catalog on December 16, 2021
PTK-7823-BK, ProTek RC Aluminum Flat Clamping Servo Horn (Black) (25T-ProTek)
This is a replacement ProTek R/C Aluminum Clamping Servo Horn, intended for use with ProTek R/C servos. This extremely tough servo-horn has been machined from a solid block of aluminum for incredible precision, rigidity and durability. The horn features a clamp type design that grips the servo’s output shaft so if the retainer screw comes loose, the horn will have a better chance of remaining in place, increasing your chances of finishing the race! Plus, the horn has a 3.5mm thick arm for durability, with 16.5mm and 20mm hole spacing threaded for 3mm hardware to suit the geometry and hardware requirements of most vehicles. Package includes one black anodized servo horn, 3x10mm button head screw, 2x7.5mm clamp screw and a star lock washer.
Features:
Clamp design
16.5mm and 20mm hole spacing (measured from output shaft screw hole, to linkage rod holes, center to center)
3.5mm thick arm
31mm Overall length
Linkage holes threaded for 3mm hardware
25T Spline ProTek Output Shaft
This product was added to our catalog on December 16, 2021
ECP-2060, EcoPower Flame Resistant LiPo Charging Bag (Large, 23x30cm)
This is the EcoPower Flame Resistant Lithium Polymer Charging Bag, and is intended to reduce the chance of damage or injury in the event of a LiPo fire.
The EcoPower LiPo Safe Charging Bag is rated up to 30 watt-hours and is made of high tech space-age materials that will help to contain a lithium polymer battery fire. Place your lithium polymer battery inside the LiPo Safe Charging Bag and extend the charging wires through the top flap. Charge your LiPo batteries in the LiPo Safe Charging Bag for peace of mind and a higher level of safety. In the event of a lithium polymer battery mishap, the LiPo Safe Charging Bag’s fire-resistant material reduces the severity of the fire inside and vents the smoke outside of the LiPo Safe Bag. The Charging Bag is sealed with a thick, industrial strength Velcro flap and can also be used for safe transportation and storage of your Lithium Polymer batteries.
Due to the volatile nature of Lithium chemistry batteries, charging bags such as the EcoPower Lithium Polymer Flame Resistant Storage Bag are required by many tracks, flight clubs and at ROAR sanctioned events.
WARNING:
Never leave charging battery unattended
Always ensure the battery is on a non-flammable surface
Ensure flap is sealed while charging
This EcoPower lithium charging bag is intended to reduce the chance of damage in the event of a LiPo fire
Not recommended for batteries exceeding 30 watt-hours
Instructions: 1. Ensure that charger rate is properly set and polarity is correct 2. Attach charging leads to battery 3. Place battery toward the bottom of the LiPo Safe Bag 4. Place the LiPo Safe Bag on a non-flammable surface 5. Route charge leads through either vent at the sides of the flap top seam of the LiPo Safe Bag 6. Close top flap of the LiPo Safe Bag and press hook and loop closure fully closed 7. Charge battery using proper charging practices
Dimensions: 230x300mm (9x11.8 inches)
This product was added to our catalog on September 6, 2024
PTK-5365, ProTek RC 2S Charge/Balance Adapter (5mm Bullet Connectors to Female XT90) (12awg) (7pin XH balance plug)
ProTek RC 2S Charge Balance Adapter. This adapter is designed to work with the Junsi iCharger 456DUO and 458DUO for charging 2S 5mm bullet batteries. Package includes one charge lead.
This product was added to our catalog on February 27, 2024
PTK-7825, ProTek RC Dual Offset Heavy Duty Clamping Servo Horn (Standard) (25T)
The ProTek R/C Dual Offset Heavy Duty Clamping Servo Horn features a dual offset allowing you to choose the best offset for your setup. The 4mm thick horn has a 20mm and 16mm hole spacing threaded for 3mm hardware to suit the geometry and hardware requirements of most vehicles. Package includes one standard length servo horn, one 3x10mm button head screw and one 2x7.5mm clamp screw.Features:
Clamp design
20mm & 16.0mm hole spacing (measured from output shaft screw hole, to linkage rod holes, center to center)
4.0mm thick arm
33mm Overall End to End length
Linkage holes threaded for 3mm hardware
25T Spline Futaba/Savox/ProTek Output Shaft
Unique Mounting Screw: PTK-H-1218
This product was added to our catalog on September 2, 2022
PTK-5308, ProTek RC 2S Charge/Balance Adapter Cable (XT60 Plug to 4mm Bullet Connector)
This is a "TruCurrent" XT60 Plug to 4mm Bullet Connector 2S balance adapter cable from ProTek R/C. ProTek R/C "TruCurrent" XT60 connectors ensure a mechanically solid, low resistance, high-amp capacity connection and are the ideal power connector for high current applications.
This product was added to our catalog on December 16, 2021
PTK-7800-BK, ProTek RC 4mm Aluminum Long Clamping Servo Horn (Black) (25T)
This is a ProTek R/C 4mm Aluminum Long Clamp Lock Servo Horn, and is intended for use with any servo that uses a 25 tooth spline output shaft. This extremely tough servo-horn has been machined from a solid block of aluminum for incredible precision, rigidity and durability. This horn features a clamp type design that grips the servo’s output shaft with enough force that even if the retainer screw comes loose, the horn will remain in place, increasing your chances of finishing the race! Additionally, the arm is 4mm thick for durability, has 19.75mm & 24.25mm hole spacing and uses 3mm hardware to suit the geometry and hardware requirements of most vehicles.
Features:
Clamp design
19.75mm & 24.25mm hole spacing (measured from output shaft screw hole, to linkage rod holes, center to center)
4mm thick arm
35.5mm Overall length
Linkage holes threaded for 3mm hardware
25T Spline Futaba/Orion/Savox/ProTek Output Shaft
This product was added to our catalog on December 16, 2021
PTK-2109, ProTek RC Braided Brushless Motor Sensor Cable (300mm)
This is a ProTek R/C Braided Brushless Motor Sensor Cable. This sensor cable is intended for use with any sensor-based brushless system that uses a replaceable sensor wire harness.
The ProTek R/C sensor cable features flexible silicone wire shielding on each of the six sensor wires, with a black braided nylon protective sheath surrounding the sensor wires. Additionally, the braided sheath is shrink wrapped at each end providing complete protection to the cable. This protection and flexibility leads to a free moving and shock absorbing sensor cable while ensuring smooth, consistent and reliable data transfer between your ESC and motor.
This product was added to our catalog on March 16, 2021
PTK-5335, ProTek RC 2S-6S 4-Battery Parallel Charger Board (T-Style/JST-XH)
This is the ProTek R/C 2S-6S 4-Battery Parallel Charger Board. Do you have a lot of batteries that take forever to charge? The ProTek R/C Parallel Charge Board will charge up to four LiPo batteries simultaneously, and also balance the individual cells of each battery during the charge process. If charging four batteries simultaneously doesn't satisfy demands, two Parallel Charge Boards can be daisy chained to charge eight batteries at once!
Be Advised: Some newer batteries (like some GensAce) come with balance plug protectors which are slightly bulky and do not properly fit this board. You will need to remove the protector or find an alternative method.
The Parallel Charger Board is also compatible with Li-Ion and LiFe Batteries. Of course, the battery charger must be compatible for the chosen battery chemistry and only that battery chemistry can be charged at once with the board (example: don't mix LiPo's with LiFe's). Additionally, the parallel charge process only works when charging batteries of the same cell count, similar age and of similar discharge states. But as long as these needs are met, plug in your batteries' T-Style/Deans power connector (or adapter) and the XH balance plug to the Parallel Charge Board, and let the juice flow.
Other features include an impact resistant custom molded plastic hard case, replaceable DC input fuse, replaceable battery port fuses, and self-resetting polyfuses protecting all balance ports.
Important Parallel Charging Rules:
Only the same battery chemistry can be charged at once (don't mix LiPo's with LiFe's, etc.)
Only same celled Lithium batteries can be charged at once (don't mix 4S with 6S, etc.)
Only charge batteries with similar states of discharge (within 0.2V)
Always program the charger to the total capacity of all attached batteries (if charging four 5000mAh batteries, set the charger to 20,000mAh, etc. It is ok to charge batteries with different mAh capacities)
Features:
Charge four batteries at once
Charge from 2S to 6S Lithium batteries
Balances each individual cell of each battery
Daisy chain multiple boards for additional charging
Convenient T-Style battery connector
4mm gold bullet input connectors
40A max current
Replaceable DC input fuse
Replaceable battery port fuses
Self-resetting polyfuses protect balance circuits
Impact resistant custom molded plastic hard case
Specifications:
Voltage: 0-22.2V DC
Max Current: 40A
Batteries: 4 packs (must be same capacity & cell count)
Battery Connector: T-Style/JST-XH
Input Connector: 4mm Gold Bullet/JST-XH
Input Connector Length: 6.75in (17.1cm)
Dimensions (LxWxH*): 6.8x3.9x0.75in (17.2x9.9x1.9cm)
*Height is 1.25 inches from the top of fuses
Note: When using the Parallel Charge Board you will lose the ability to monitor each pack independently. The information the charger displays will be an average of all the cells attached.
This product was added to our catalog on December 16, 2021
PTK-8290, ProTek RC 6" Digital Caliper w/LCD Display & Hard Case
ProTek RC 6" Digital Calipers feature a high-contrast LCD display, stainless steel construction and guaranteed accuracy to 0.001"/0.02mm, making them a must have for any enthusiasts tool box! The tool delivers accurate readings of inside, outside, step and depth measurements that are useful in a variety of applications. Additionally, a plastic storage case is included to keep the tool safe during storage, and two LR44 batteries are included so that you don't need to find another battery when the first one dies!
Features:
Corrosion resistant stainless steel
Convenient auto-off feature
Dual mode LCD display - Inches and Metric
Inside, outside, depth & step measurements
Accuracy: +/- 0.001" +/- 0.02mm
Power Source: 1 LR44/SR44 battery (two included)
NOTE: For replacement batteries see part PTK-5199.
This product was added to our catalog on December 16, 2021
PTK-2553, ProTek RC N3 Hot Standard Glow Plug (.12, .15 and .18 Engines)
The ProTek R/C N3 Hot Standard Glow Plug is a great plug option for .12-.15 to .18 size engines used in monster trucks such as the original and newer 2.5 and 3.3 Traxxas T-Maxx trucks. This plug is recommended for hotter/humid conditions and will provide a more stable idle and crisp acceleration when compared to a cold plug. This plug is recommended for low nitro content fuels (10-20%).
NOTE: For Traxxas applications, use one washer. For O.S. engines use two washers.
This product was added to our catalog on December 16, 2021
PTK-8417, ProTek RC "TruTorque SL" Metric Ball End Hex Driver Set (4)
Features:
CNC machined knurled aluminum handle with relief holes
Rotating aluminum end cap
Durable, precision cut, 80mm long HSS Steel tip
Tip size is etched in three places on the handle for easy identification
Includes:
(1) 1.5mm Ball End Hex Driver
(1) 2.0mm Ball End Hex Driver
(1) 2.5mm Ball End Hex Driver
(1) 3.0mm Ball End Hex Driver
This product was added to our catalog on December 16, 2021
KYOMZH131W, Kyosho Mini-Z 2WD Rays RE30 Multi Offset Wheel Set II (White) (20)
This is an optional Kyosho Mini-Z 2WD Rays RE30 Multi Offset Wheel Set II. This is the complete Rays RE30 wheel set and is a great option for tuning Mini-Z AWD models for improved handling, or to suit different bodies. Plus, the bright white plastic is perfect for adding a personalized touch with your prefered color paint. Package includes narrow and wide type wheels, two of each. Narrow: 8.5mm 0/+1.0/+1.5 /+2.0/+2.5; Wide: 11mm -1.0/+0/+1/+2/+3 .
This product was added to our catalog on November 1, 2024
