PTK-5335, ProTek RC 2S-6S 4-Battery Parallel Charger Board (T-Style/JST-XH)
This is the ProTek R/C 2S-6S 4-Battery Parallel Charger Board. Do you have a lot of batteries that take forever to charge? The ProTek R/C Parallel Charge Board will charge up to four LiPo batteries simultaneously, and also balance the individual cells of each battery during the charge process. If charging four batteries simultaneously doesn't satisfy demands, two Parallel Charge Boards can be daisy chained to charge eight batteries at once!
Be Advised: Some newer batteries (like some GensAce) come with balance plug protectors which are slightly bulky and do not properly fit this board. You will need to remove the protector or find an alternative method.
The Parallel Charger Board is also compatible with Li-Ion and LiFe Batteries. Of course, the battery charger must be compatible for the chosen battery chemistry and only that battery chemistry can be charged at once with the board (example: don't mix LiPo's with LiFe's). Additionally, the parallel charge process only works when charging batteries of the same cell count, similar age and of similar discharge states. But as long as these needs are met, plug in your batteries' T-Style/Deans power connector (or adapter) and the XH balance plug to the Parallel Charge Board, and let the juice flow.
Other features include an impact resistant custom molded plastic hard case, replaceable DC input fuse, replaceable battery port fuses, and self-resetting polyfuses protecting all balance ports.
Important Parallel Charging Rules:
Only the same battery chemistry can be charged at once (don't mix LiPo's with LiFe's, etc.)
Only same celled Lithium batteries can be charged at once (don't mix 4S with 6S, etc.)
Only charge batteries with similar states of discharge (within 0.2V)
Always program the charger to the total capacity of all attached batteries (if charging four 5000mAh batteries, set the charger to 20,000mAh, etc. It is ok to charge batteries with different mAh capacities)
Features:
Charge four batteries at once
Charge from 2S to 6S Lithium batteries
Balances each individual cell of each battery
Daisy chain multiple boards for additional charging
Convenient T-Style battery connector
4mm gold bullet input connectors
40A max current
Replaceable DC input fuse
Replaceable battery port fuses
Self-resetting polyfuses protect balance circuits
Impact resistant custom molded plastic hard case
Specifications:
Voltage: 0-22.2V DC
Max Current: 40A
Batteries: 4 packs (must be same capacity & cell count)
Battery Connector: T-Style/JST-XH
Input Connector: 4mm Gold Bullet/JST-XH
Input Connector Length: 6.75in (17.1cm)
Dimensions (LxWxH*): 6.8x3.9x0.75in (17.2x9.9x1.9cm)
*Height is 1.25 inches from the top of fuses
Note: When using the Parallel Charge Board you will lose the ability to monitor each pack independently. The information the charger displays will be an average of all the cells attached.
This product was added to our catalog on December 16, 2021
PTK-8417, ProTek RC "TruTorque SL" Metric Ball End Hex Driver Set (4)
Features:
CNC machined knurled aluminum handle with relief holes
Rotating aluminum end cap
Durable, precision cut, 80mm long HSS Steel tip
Tip size is etched in three places on the handle for easy identification
Includes:
(1) 1.5mm Ball End Hex Driver
(1) 2.0mm Ball End Hex Driver
(1) 2.5mm Ball End Hex Driver
(1) 3.0mm Ball End Hex Driver
This product was added to our catalog on December 16, 2021
KYOMZH131W, Kyosho Mini-Z 2WD Rays RE30 Multi Offset Wheel Set II (White) (20)
This is an optional Kyosho Mini-Z 2WD Rays RE30 Multi Offset Wheel Set II. This is the complete Rays RE30 wheel set and is a great option for tuning Mini-Z AWD models for improved handling, or to suit different bodies. Plus, the bright white plastic is perfect for adding a personalized touch with your prefered color paint. Package includes narrow and wide type wheels, two of each. Narrow: 8.5mm 0/+1.0/+1.5 /+2.0/+2.5; Wide: 11mm -1.0/+0/+1/+2/+3 .
This product was added to our catalog on November 1, 2024
ECP-1015, EcoPower NiMH & NiCD USB Battery Charger (4 Slots) (AA/AAA)
Intelligent State-of-the-Art Battery Charger
Introducing the EcoPower Nickel-Metal Hydride (NiMH) and Nickel-Cadmium (NiCD) USB Battery Charger, an advanced solution for your battery charging needs. This state-of-the-art charger combines intelligent microcomputer control with precise voltage monitoring to ensure your batteries are charged efficiently and safely. With features designed to protect your batteries and optimize performance, it provides a reliable and user-friendly charging experience.
Advanced Charging Control
The EcoPower NiMH and NiCD USB Battery Charger utilizes cutting-edge charging control technology to monitor battery voltage in real time. This includes a constant current pulse charging scheme tailored specifically for NiMH and NiCD batteries, guaranteeing optimal charging effectiveness. The charger is equipped with three distinct "stop-charging" judgments to protect against overcharging and ensure battery longevity.
Versatile Charging Capabilities
This charger supports up to four AA or AAA NiMH and NiCD batteries simultaneously, offering flexibility and convenience. The micro USB interface allows for easy connectivity and the intelligent microcomputer control manages each slot independently, ensuring that all batteries are charged efficiently according to their specific needs. Additionally, the inclusion of a red and green two-color LED indicator in each slot provides instant visual feedback on the charging status.
Safety and Protection Features
Safety is paramount with the EcoPower USB Charger, which includes multiple protection features to safeguard both the charger and your batteries. It has reverse battery protection and short circuit protection, minimizing the risk of damage from incorrect battery placement or electrical faults. The charger's maximum voltage stop-charging feature further protects against overcharging, ensuring the battery voltage does not exceed safe levels.
Features:
Micro USB interface input
Intelligent microcomputer control
Supports one to four AA or AAA batteries
Independent charging for each slot
Red and green LED indicators
Reverse battery protection
Short circuit protection
Constant current pulse charging
Maximum voltage stop charging protection
Real-time voltage monitoring
This product was added to our catalog on November 1, 2024
PTK-5364, ProTek RC 2S Charge/Balance Adapter (4mm Bullet Connectors to Female XT90) (12awg) (7pin XH balance plug)
ProTek RC 2S Charge Balance Adapter. This adapter is designed to work with the Junsi iCharger 458DUO and 456DUO for charging 2S 4mm bullet batteries. Package includes one charge lead.
This product was added to our catalog on February 27, 2024
PTK-5367, ProTek RC 2S Charge/Balance Adapter (4mm Bullet Connectors to Female XT90) (12awg) (9pin XH balance plug)
ProTek RC 2S Charge Balance Adapter. This adapter is designed to work with the Junsi iCharger 458DUO for charging 2S 4mm bullet batteries. Package includes one charge lead.
Note: This Charge lead has a 9pin XH balance plug and is not compatible with the Junsi 456DUO
This product was added to our catalog on February 27, 2024
PTK-1KTBL, ProTek RC 1KTBL Black Label Ultra High Torque Brushless Waterproof Crawler Servo (High Voltage/Metal Case) (Digital)
The ProTek 1KTBL was developed to satisfy the needs of torque thirsty enthusiasts. With the ability to deliver over 1000 oz-in of torque and .11 transit speeds at 8.4V, there aren't many servo options that can compete. Competition rigs, heavy scalers and bashers can take advantage of what the 1KTBL delivers. Even large scale surface models and airplanes can benefit from the insane torque the 1KTBL can produce.
All this power means nothing without durability - and the Protek 1KTBL punches far outside its weight class. This servo offers the power, reliability and durability needed to keep the competition on the ropes. The proven gasket system allows waterproof protection up to 1-meter, so it will go the distance in any condition. A full steel gear train, 25T output shaft and full aluminum machined heat sink case finish off the package to create a tough servo that is perfect for demanding applications. The 1KTBL delivers power in excess - with the durability and reliability that make ProTek R/C servos a an easy choice for enthusiasts that expect the most from their rigs.
NOTE:
For best results, and peak performance, we recommend you power this servo with a BEC.
If you experience glitching or poor performance while using a Futaba transmitter, you must turn off BLS mode. BLS mode is only compatible with Futaba BLS type servos.
Requires a servo extension lead for a drop-in TRX-4 fit.
Features:
Ideal for a variety of applications
Waterproof up to 1 meter
880 oz-in of torque @ 6.0V, and .16 transit speed
1080 oz-in of torque @ 8.4V, and .11 transit speed
Brushless motor
High voltage circuitry
Full steel gears
Full aluminum black anodized heat sink case
Dual ball bearings
260mm servo lead
Servo Model
1KTBL
Recommended Application
Crawlers, Bashers & Large Scale
Operating Voltage
4.8V - 8.4V
Operating Temperature
14° to 140° F (-10 to +60° C)
Operating Speed @ 6.0V
0.16/60° sec
Operating Speed @ 8.4V
0.11/60° sec
Dynamic Torque @ 6.0V
880 oz-in (63.6 kg-cm)
Dynamic Torque @ 8.4V
1080 oz-in (77.7 kg-cm)
Stall Current @ 6.0V
7.7A
Stall Current @ 8.4V
8.3A
Motor Type
Brushless Digital
Output Shaft
25 Tooth
Gears
Steel
Weight
81g
Pulse/Frequency
1520s / 333hz
Dimensions
41x21x39.5mm
Length (Bottom to Mount)
30mm
This product was added to our catalog on June 17, 2023
PTK-5332, ProTek RC 1S 12-Battery Parallel Charger Board (Ultra Micro/JST-PH)
This is the ProTek R/C 1S 12-Battery Parallel Charger Board. Do you have a lot of micro flight batteries to charge? The ProTek R/C Parallel Charge Board will charge up to twelve 1S LiPo flight batteries simultaneously. Six charge ports are compatible with MX connectors (also known as pico or ultra micro), used on the mSR and other ultra micro aircraft. Six more charge ports are included featuring 2-pin JST-PH connectors found on Blade, E-flite and ProTek R/C batteries. Your battery charger must be compatible for LiPo chemistry and the parallel charge process only works when charging batteries of the similar age and of similar discharge states. As long as these needs are met, plug in your 1S batteries to the Parallel Charge Board and let the juice flow.
Warranty Info Icon smallImportant Parallel Charging Rules:
Only charge LiPo chemistry batteries Only charge 1S LiPo batteriesOnly charge batteries with similar states of discharge (within 0.2V)Always program the charger to the total capacity of all attached batteries (Example: if charging five 200mAh batteries, set the charger to 1,000mAh. *It is ok to charge batteries with different mAh capacities)Features:
Charge twelve batteries at onceConvenient XM and 2-Pin JST-PH battery connectors4mm gold bullet input connectors Specifications:Batteries: 12x 1S 3.7V batteriesBattery Connector: 6x Ultra Micro & 6x 2-pin JST-PHInput Connector: 4mm Gold BulletInput Connector Length: 5.50in (13.9cm)Dimensions (LxWxH*): 2.5x1.25x0.5in (6.4x3.2x1.2cm)
This product was added to our catalog on December 16, 2021
PTK-5197, ProTek RC 1S LiPo Transmitter Battery (Sanwa M17/MT-44) (3.7V/3000mAh)
This ProTek R/C 1S 3000mAh LiPo transmitter pack was developed specifically for the Airtronics/Sanwa M17, MT-44 and MT-5 ransmitters. This light weight LiPo battery will help to reduce the overall weight of your transmitter, which is great for long main events! The overall weight will be significantly reduced when compared to a typical NiMH transmitter pack and will provide an incredible amount of run time!
How should the battery be inserted into the transmitter?A suitable foam should be used to pad the battery in the transmitter battery compartment to help hold the battery in place and prevent it from moving around. Place a piece similar in size to the battery into the transmitter battery housing under the battery, and then while pressing lightly on the battery, slide the cover over the battery.
Specifications:
Voltage: 3.7V
Capacity: 3000mah
Chemistry: Lithium Polymer
Connector: JR
Charge Rate: 2C
Dimension (LxWxH): 62.5x45x8.5mm
Weight: 52g
IMPORTANT:1) DO NOT leave the battery in your model when charging2) DO NOT leave unattended when charging3) ALWAYS balance charge the battery4) ALWAYS use a LiPo charging bag5) YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)6) YOU MUST not over discharge the Li-Poly battery pack7) READ & UNDERSTAND the instructions carefully before operating this batteryNOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on December 16, 2021
PTK-8069, ProTek RC Steel Mod 1 Pinion Gear (5mm Bore) (16T)
ProTek R/C Steel Mod 1 Pinion Gears are an affordable pinion gear option that doesn't skimp on quality. CNC machined from hardened steel material, these precision cut gears are durable and are perfect for any Mod 1 pitch application. Available in 11 - 20 tooth variants, these gears feature a 5mm bore with the tooth count engraved on the gear for easy identification. Plus, each gear includes a setscrew to make installation easy.
This product was added to our catalog on December 16, 2021
KYOMZW40-30, Kyosho Super Low Height Slick Tire (4) (30 Deg)
Tire Overview:
The Kyosho Super Low Height Slick Tires are a low profile tire option for your Kyosho Mini-Z. These tires will smooth out steering response, making the car easier to drive on urethane or RCP track surfaces. Use the menu above to choose from twenty, thirty, or forty degree durometer options. Package includes four tires.
This product was added to our catalog on November 1, 2024
PTK-5368, ProTek RC 2S Charge/Balance Adapter (5mm Bullet Connectors to Female XT90) (12awg) (9pin XH balance plug)
ProTek RC 2S Charge Balance Adapter. This adapter is designed to work with the Junsi iCharger 458DUO for charging 2S 5mm bullet batteries. Package includes one charge lead.
Note: This Charge lead has a 9pin XH balance plug and is not compatible with the Junsi 456DUO
This product was added to our catalog on February 27, 2024
PTK-5358, ProTek RC Heavy Duty QS8 Charge Lead (Male QS8 to Female XT90)
The ProTek R/C Heavy Duty QS8 Charge Lead Adapter features a male QS8 connected to a female XT90. This adapter is designed for the Junsi 456DUO and 458DUO, as well as, any chargers that use an XT90 charge port. Package includes one charge lead.
This product was added to our catalog on February 27, 2024
PTK-1102-CA, ProTek RC Universal Chassis Protective Sheet (California) (2) (12.5x33.5cm)
The ProTek RC Universal Uncut "Thick" Chassis Protective Sheet is 12.5cm wide by 33.5cm long and designed for universal use. This protective sheet is made from thick laminate and backed by an aggressive adhesive vinyl.
Protective sheets are highly recommended for use on new and used chassis to resist against scratches and scrapes and prolong the life of the chassis. For best results, always replace the sheet when noticeable wear occurs.
In addition to protecting the chassis, this sheet also provides a slick and smooth chassis surface which reduces friction when contacting the race surface - especially clay! If you happen to land hard and bottom out, your buggy should more easily slide through it and maintain momentum.
Features:
Made from genuine 3M® material
Thick long lasting laminate
Protects against scratches and wear
Keeps chassis looking new
Uncut for universal use
Made in the USA
12.5cm (4.9") wide x 33.5cm (13.2") long
Available in a variety of colors
Includes two sheets
This product was added to our catalog on January 16, 2024
PTK-1102-WHT, ProTek RC Universal Chassis Protective Sheet (White) (2) (12.5x33.5cm)
The ProTek RC Universal Uncut "Thick" Chassis Protective Sheet is 12.5cm wide by 33.5cm long and designed for universal use. This protective sheet is made from thick laminate and backed by an aggressive adhesive vinyl.
Protective sheets are highly recommended for use on new and used chassis to resist against scratches and scrapes and prolong the life of the chassis. For best results, always replace the sheet when noticeable wear occurs.
In addition to protecting the chassis, this sheet also provides a slick and smooth chassis surface which reduces friction when contacting the race surface - especially clay! If you happen to land hard and bottom out, your buggy should more easily slide through it and maintain momentum.
Features:
Made from genuine 3M® material
Thick long lasting laminate
Protects against scratches and wear
Keeps chassis looking new
Uncut for universal use
Made in the USA
12.5cm (4.9") wide x 33.5cm (13.2") long
Available in a variety of colors
Includes two sheets
This product was added to our catalog on January 16, 2024
PTK-7824, ProTek RC Dual Offset Heavy Duty Clamping Servo Horn (Long) (25T)
The ProTek R/C Dual Offset Heavy Duty Clamping Servo Horn features a dual offset allowing you to choose the best offset for your setup. The 4mm thick horn has a 25mm and 20mm hole spacing threaded for 3mm hardware to suit the geometry and hardware requirements of most vehicles. Package includes one long servo horn, one 3x10mm button head screw and one 2x7.5mm clamp screw.Features:
Clamping design
25mm & 20mm hole spacing (measured from output shaft screw hole, to linkage rod holes, center to center)
4.0mm thick arm
37.5mm Overall End to End length
Linkage holes threaded for 3mm hardware
25T Spline Futaba/Savox/ProTek Output Shaft
Unique Mounting Screw: PTK-H-1218
This product was added to our catalog on September 2, 2022
PTK-5131-22, ProTek RC 4S 130C Low IR Si-Graphene+ HV Shorty LiPo Battery (15.2V/6400mAh) w/5mm Connector (ROAR Approved)
The ProTek R/C 4S Shorty 130C Low IR 6400mAh Silicon Graphene+ HV Battery is a great option for 1/8 scale racers looking for a high capacity, high output and incredibly COMPACT 4S battery. Weighing approximately 440 grams, the 4S Shorty is almost 13 grams lighter than the PTK-5118-22 5600mAh 4S pack with more capacity! This offers more capacity output, in a compact shorty length that is perfect for weight conscious racers.
ProTek R/C Silicon Graphene batteries are the next step in the evolution of LiPo battery technology. Silicone Graphene construction offers improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage!
When compared to standard LiPo and LiHV, Silicon Graphene cells deliver an array of benefits! Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle - with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 100C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C Silicon Graphene packs are perfect for racers and bashers that demand the absolute best.
While these batteries are technically LiHV cells, they can still be charged with a standard LiPo charger. The overall voltage and capacity will be slightly less than if charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the reduced weight and low internal resistance.
NOTE: This battery is not recommended for high current draw 8S applications
MBX8 Eco Shorty Battery.
Features:
Shorty 4S configuration is lighter and smaller than the PTK-5118-20 4S pack, with increased capacity
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Increased run time, increased cycle life and increased voltage!
More capacity gram for gram when compared to standard LiPo cells
10C max charge rates - 1C charge rate recommended for longest life
15.2V nominal voltage
Replacement XH4S balance adapter also available separately (PTK-5331)
Battery Model
4S Shorty HV LiPo
ROAR Approved
Yes
Type
Silicon Graphene
Voltage
15.2V nominal
Capacity @14.8V
5800mAh
Capacity @15.2V
6400mAh
Weight
440g ±10
Connector Type
5mm Bullet
Balance Connector
XH4S Adapter
Number of Cells
4 Cell
Configuration
4S2P
Dimensions (WxLxH)
47x98.5x48mm
Maximum Charge Rate
10C (64A)
Burst Current
130C
Watt Hour @15.2V
97.2Wh
Includes:
(1) ProTek R/C Battery
(2) 5mm to 4mm Bullet Reducers
(2) 5mm Bullet Connectors
(1) 4S Balance Lead
LITHIUM POLYMER SAFETY INFORMATION
IMPORTANT: 1) DO NOT leave the battery in your model when charging 2) DO NOT leave unattended when charging 3) ALWAYS balance charge the battery 4) ALWAYS use a LiPo charging bag 5) YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!) 6) YOU MUST not over discharge the Li-Poly battery pack 7) READ & UNDERSTAND the instructions carefully before operating this battery NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.
Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on January 24, 2022
This ProTek R/C 2S Charge/Balance Adapter features a T-Style connector and is intended for use with 2S LiPo batteries that have 8mm output sockets. This adapter cable will allow you to balance charge your 8mm socket equipped batteries easily, eliminating the need to build your own cable. Package includes one charge/balance adapter.
PTK-5242, ProTek RC 20cm "XH" Multi-Adapter Balance Cable (6S Charger To 6S Balance Board)
This is a multi-adapter balance cable from ProTek R/C. The multi-adapter balance cable allows you to use any of the ProTek R/C 6S multi-adapter balance boards with your ProTek R/C 6S balance charger. This cable may also be used as a longer cable on the EOS, LBA10 and Hyperion Balance Chargers, or any other charger that uses an XH compatible balance adapter port.
This product was added to our catalog on May 18, 2021
