PTK-5131-21, ProTek RC 4S Shorty 120C Low IR Silicon Graphene+ HV LiPo Battery (15.2V/6000mA)This product was added to our catalog on December 16, 2021
PTK-5131-22, ProTek RC 4S 130C Low IR Si-Graphene+ HV Shorty LiPo Battery (15.2V/6400mAh) w/5mm Connector (ROAR Approved)
The ProTek R/C 4S Shorty 130C Low IR 6400mAh Silicon Graphene+ HV Battery is a great option for 1/8 scale racers looking for a high capacity, high output and incredibly COMPACT 4S battery. Weighing approximately 440 grams, the 4S Shorty is almost 13 grams lighter than the PTK-5118-22 5600mAh 4S pack with more capacity! This offers more capacity output, in a compact shorty length that is perfect for weight conscious racers.
ProTek R/C Silicon Graphene batteries are the next step in the evolution of LiPo battery technology. Silicone Graphene construction offers improved efficiency, lower operating temperatures, lower internal resistance, better run time, increased cycle life and increased voltage!
When compared to standard LiPo and LiHV, Silicon Graphene cells deliver an array of benefits! Lab testing has shown that ProTek R/C Silicon Graphene packs have double the cycle life when charged at 1C rates, and can be charged at higher amp rates, with less risk of damage to the pack. More importantly, the discharge curve is flatter, meaning the cells maintain higher voltage throughout the discharge cycle - with no significant drop off. Additionally, when compared to conventional LiPo batteries Silicon Graphene batteries are lighter, providing a higher capacity per gram ratio. With 7.6V nominal voltage, 100C discharge ratings, incredibly high charge rates and ten different models to choose from, ProTek R/C Silicon Graphene packs are perfect for racers and bashers that demand the absolute best.
While these batteries are technically LiHV cells, they can still be charged with a standard LiPo charger. The overall voltage and capacity will be slightly less than if charged to LiHV specs, but the performance will be better than a standard LiPo thanks to the reduced weight and low internal resistance.
NOTE: This battery is not recommended for high current draw 8S applications
MBX8 Eco Shorty Battery.
Features:
Shorty 4S configuration is lighter and smaller than the PTK-5118-20 4S pack, with increased capacity
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Increased run time, increased cycle life and increased voltage!
More capacity gram for gram when compared to standard LiPo cells
10C max charge rates - 1C charge rate recommended for longest life
15.2V nominal voltage
Replacement XH4S balance adapter also available separately (PTK-5331)
Battery Model
4S Shorty HV LiPo
ROAR Approved
Yes
Type
Silicon Graphene
Voltage
15.2V nominal
Capacity @14.8V
5800mAh
Capacity @15.2V
6400mAh
Weight
440g ±10
Connector Type
5mm Bullet
Balance Connector
XH4S Adapter
Number of Cells
4 Cell
Configuration
4S2P
Dimensions (WxLxH)
47x98.5x48mm
Maximum Charge Rate
10C (64A)
Burst Current
130C
Watt Hour @15.2V
97.2Wh
Includes:
(1) ProTek R/C Battery
(2) 5mm to 4mm Bullet Reducers
(2) 5mm Bullet Connectors
(1) 4S Balance Lead
LITHIUM POLYMER SAFETY INFORMATION
IMPORTANT: 1) DO NOT leave the battery in your model when charging 2) DO NOT leave unattended when charging 3) ALWAYS balance charge the battery 4) ALWAYS use a LiPo charging bag 5) YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!) 6) YOU MUST not over discharge the Li-Poly battery pack 7) READ & UNDERSTAND the instructions carefully before operating this battery NOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.
Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on January 24, 2022
PTK-5141-22, ProTek RC 2S 50C 1100mAh Losi Mini T/B & JRX2 LiPo Battery w/EC2 Connector
The Protek R/C 2S 50C 1100mAh Losi Mini T/B and JRX2 LiPo Battery is built with performance in mind. Using Silicon Graphene technology this battery packs a punch with it's 50c discharge rating! Designed to work with the Losi Mini T, B and Mini JRX2 this pack offers extended runtimes with it's larger 1100mah capacity. Equipped with an EC2 style connector makes this a plug in option with no need to mess with adapters or to get out the soldering iron. With more time on the track and the ability to dish out the power this Protek battery pack is an excellent upgrade for your Mini T, B or JRX2 vehicles.
Features:
Direct fit for Losi Mini B, T and JRX2 vehicles
More runtime, with a dramatic increase in punch
Silicone Graphene can handle more abuse and deliver more current than a standard LiPo battery
Improved efficiency, lower operating temperatures, and lower internal resistance!
Factory installed EC2 plug
Battery Model
2s 50C 1100mAh
Application
Air, Ground
Type
Silicon Graphene
Voltage
7.4V nominal
Capacity @7.4V
1100mAh
Weight
68g
Connector Type
EC2
Balance Connector
XH Connector
Number of Cells
2 Cell
Configuration
2S1P
Dimensions (LxWxH)
58x32x20mm
Maximum Charge Rate
4C (4.4A)
Watt Hour @7.4V
8.14Wh
Includes:
(1) ProTek R/C Battery
This product was added to our catalog on September 1, 2022
PTK-5181, ProTek RC Kyosho Mini-Z LiFe Battery Charging Wire Harness
This is a ProTek R/C Kyosho Mini-Z LiFe Battery Charging Wire Harness, and is intended for use with the ProTek R/C Kyosho Mini-Z LiFe battery.
This product was added to our catalog on December 16, 2021
PTK-5184, ProTek RC 1S High Power Micro Heli/Airplane 25C LiPo Battery (3.7V/160mAh)
This is the ProTek R/C 1S 160mAh, 25C Micro Helicopter/Airplane Lithium Polymer battery pack. This pack will fit E-Flite and Parkzone products that use 70mah to 150mAh battery packs. When used in aircraft that normally use 70mAh batteries, these batteries will provide better performance and longer flight times!
Specifications:
Type: Lithium Polymer
Capacity: 160 mAh
Voltage: 3.7V nominal
Connector Type: Molex
Number of Cells: 1
Weight: 4g
Dimensions: 43x12x5mm (1.75x.5x.25")
Maximum Charge Rate: 1C (160mAh)
Maximum Continuous Discharge: 25C (4.0A)
This product was added to our catalog on May 18, 2021
PTK-5188, ProTek RC LiFe Futaba Transmitter Battery Pack (6.6V/2100mAh) (3PV/4PK/4PM/4PLS/4PX/4PV/7PX/7PXR/10PX/16SZ)
This is the ProTek R/C LiFe Car Transmitter Battery Pack, and is intended for use with the Futaba 3PV, 4PK, 4PM, 4PV, 4PLS, 4PX, 7PX, 10PX, 16SZ, and 18SZ Transmitters. Lithium battery technology is evolving. With cell dimensions that fit anywhere a standard Li-Po battery will and rapidly increasing capacity, LiFe chemistry will soon set the standard that all others are judged by. With the ability to deliver 1000+ usable cycles, and a life span up to 4 times longer than Li-Poly batteries (when cycled under the same discharge conditions), these batteries offer the user an excellent balance of performance and value. LiFe batteries are more durable than Li-Poly and are able to handle a higher level of abuse when compared to Li-Poly without the risk of pre-mature failure. Unlike Li-Poly, LiFe cells can be stored in a fully charged state with little to no loss in stored power, and can be discharged deeper with less risk of damage to the cells. Most importantly, LiFe batteries are SAFE! There is no risk of combustion! LiFe cells will not catch fire or explode when over charged, or after a deep discharge.
What about the voltage?
A 2 Cell LiFe battery produces 6.6 volts nominal, which is almost a full volt less than a 2 Cell LiPo battery. The LiFe battery is not meant to replace the performance of a Li-Po battery, it is simply another option. LiFe offers the user a battery with a good discharge curve that is better than that of a NiMH battery, but without the risk of damage or fire that exists when a LiPo battery is abused.
NOTE: Brand new LiFePO4 batteries have been found to fail prematurely if they are deep discharged below below 33% capacity too early. A break-in period of 20 cycles is currently recommended. While testing has shown that this battery can be charged at up to 3C rates, it is recommended that this battery not be charged at rates higher than 1C to maximize the lifespan of the battery. Additionally, LiFe batteries should not be discharged below 2.5V per cell to avoid pre-mature failure and maximize battery life span.
We also recommend you REMOVE the batteries from your cars or radios when you are done, or at least unplug them to avoid accidental over discharge if the unit is left on.
Features:
Safe chemistry will not explode or catch fire
More mAh per gram compared to NiMH cells, meaning lighter models, and longer runtime
Virtually no "self discharge", so the battery is always ready to go even weeks after charging.
Superior voltage performance under load compared to NiMH cells, with consistent torque and speed.
Fast charge time
Specifications:
Voltage: 6.6V
Capacity: 2100mah
Chemistry: LiFePO4
Balance Charge Plug: XH
Charge Rate: 1C
Compatibility: Futaba 3PV, 4PK, 4PM, 4PV, 4PLS, 4PX, 7PX, 10PX, 16SZ, and 18SZ
Discharge Plug: JR/Futaba
Dimension (LxWxH): 76x41x17mm
Weight: 105g
This product was added to our catalog on December 16, 2021
PTK-5197, ProTek RC 1S LiPo Transmitter Battery (Sanwa M17/MT-44) (3.7V/3000mAh)
This ProTek R/C 1S 3000mAh LiPo transmitter pack was developed specifically for the Airtronics/Sanwa M17, MT-44 and MT-5 ransmitters. This light weight LiPo battery will help to reduce the overall weight of your transmitter, which is great for long main events! The overall weight will be significantly reduced when compared to a typical NiMH transmitter pack and will provide an incredible amount of run time!
How should the battery be inserted into the transmitter?A suitable foam should be used to pad the battery in the transmitter battery compartment to help hold the battery in place and prevent it from moving around. Place a piece similar in size to the battery into the transmitter battery housing under the battery, and then while pressing lightly on the battery, slide the cover over the battery.
Specifications:
Voltage: 3.7V
Capacity: 3000mah
Chemistry: Lithium Polymer
Connector: JR
Charge Rate: 2C
Dimension (LxWxH): 62.5x45x8.5mm
Weight: 52g
IMPORTANT:1) DO NOT leave the battery in your model when charging2) DO NOT leave unattended when charging3) ALWAYS balance charge the battery4) ALWAYS use a LiPo charging bag5) YOU MUST use a Li-Poly specific charger to charge the pack (NiMH or NiCD only chargers WILL NOT WORK!)6) YOU MUST not over discharge the Li-Poly battery pack7) READ & UNDERSTAND the instructions carefully before operating this batteryNOTE: When using high energy Li-Polymer Batteries, please do not over-discharge or over-charge batteries as this will result in over heated batteries. Discharging capacity can't exceed 80% of the max capacity of the pack after full charging to ensure a good cycle performance. It is recommended to fully charge a brand new battery before using and only discharge the battery 50% for first 5 cycles. Always monitor race time and/or set a low voltage warning on ESC (End voltage cannot be lower than 3.2v per cell). Do not use the battery that has too low a voltage.Do not expose batteries to sunshine or store/charge batteries at the temperature above 35°C or in a closed car. The high temperature environment could cause damage to the pack or make it burst. If the battery becomes hot while fast charging, high current discharging or racing, do not charge the battery until it has cooled completely. Wait about 20 mins, then inspect prior to recharging.
This product was added to our catalog on December 16, 2021
PTK-5200, ProTek RC T-Style Ultra Plug Female Battery Pigtail (10cm, 14awg wire) (1)
This is a female T-style ultra plug pigtail from ProTek R/C. The ultra plug is connected to 10cm of 14awg silicone wire.
This product was added to our catalog on December 16, 2021
PTK-5201, ProTek RC T-Style Ultra Plug Male Device Pigtail (10cm, 14awg wire) (1)
This is a male T-style ultra plug pigtail from ProTek R/C. The ultra plug is connected to 10cm of 14awg silicone wire.
This product was added to our catalog on October 29, 2007
PTK-5211, ProTek RC Heavy Duty 15cm Universal Servo Y Extension Lead (1 Male/2 Female)
This is one 15cm (6") universal servo Y extension lead from ProTek R/C. These are excellent servo extension leads made with thick, high quality 22awg wire for maximum current carrying capacity and strength.
The male plug installed on these extension leads are JR style connectors and will work with any radio system. The two female ends are designed to accept Futaba connectors, as well as JR, Aitronics and HiTec connectors. When plugging JR style connectors into the female connector, be sure to check for the correct polarity.
This product was added to our catalog on December 16, 2021
PTK-5213, ProTek RC Receiver Charge Lead (Futaba Female to 4mm Banana Plugs)
This is one receiver charge lead lead from ProTek R/C. This charge lead has a Futaba style battery connector on one end that will accept both Futaba and JR/Airtronics style battery connectors, connected to 4mm banana plugs with high quality 22awg silicone wire.This product was added to our catalog on July 6, 2021
PTK-5216, ProTek RC Heavy Duty T-Style Ultra Plug Charge Lead (Male to 4mm Banana)
This is the ProTek R/C Heavy Duty T-Style Charge Lead, featuring a T-style ultra plug on one end connected to 4mm banana plugs with high quality 14awg silicone wire.
This charge lead can be used for heavy duty charging due to the 14awg wire, and can be used to charge at rates more than 20 amps. In total length, the lead measures 8.5 inches (21.6cm) long from end to end.
This product was added to our catalog on December 16, 2021
