This antenna is exceptionally powerful, extending your drone's range and reducing interference and noise from other devices or networks. This is a dual band patch antenna designed to be used with the dji fpv goggles version 2 and the dji fpv drone now this antenna is designed to give you the best possible performance from this system. It offers an optimal connection from the DJI FPV Goggles V2 to the DJI FPV Drone, DJI Avata Drone, and DJI O3 Air Unit. Pilots have reported a reliable video connection of up to 9.63 miles (15.4 km). Manufactured in Los Angeles, California with the finest materials, this antenna is made in the USA.
Check out all out FPVTEC Products, FPV Receivers & Antennas, and our DJI compatible gear!
Features
Compatible with the DJI FPV Drone, Avata Drone, and DJI O3 Air Unit
Low Loss Coaxial Cables - Rated up to 6 GHz
Antenna mount fits the DJI FPV Goggles V2
Solid video at 9.63 Miles / 15.4 km
Extends the range of your drone
Linear and Vertical Polarization
High-Quality Material
Made in the USA
Specifications
Compatibility: DJI FPV Drone, DJI Avata Drone, and DJI O3 Air Unit
Gain : 9dBi @ 5.8 GHz 6.5 dBi @ 2.4 GHz
Antenna Mount: Fits DJI FPV Goggles V2
Horizontal: 5.8 GHz: 55° 2.4 GHz 75°
Vertical: 5.8 GHz: 65° 2.4 GHz: 70°
Polarization: Linear, Vertical
VSWR : 2.0:1
Weight: 160g
Includes
1x FPVTEC Kaiju 5.8GHz / 2.4GHz Range Extender Dual Band Patch Antenna for DJI Goggles V2 - Linear / Vertical
1x 3D Printed Mount (Preassembled)
2x Low Loss Coaxial Cables
2x Precision Thumb Screws
4x Nano SMA Grips
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 65 Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Whoop Micro Frame kit and HappyModel Mobula6 Whoop frame.
Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 65mm whoop frame, and that will serve as your protection for your motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
Check out our other Micro frames, and our Fractal Engineering Products!
Features
65mm diagonal, squished X geometry, for 31mm props
1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction
Low-profile camera mount, no props in view, no tilt offset
Low Center of gravity, by bringing the AIO closer to the frame/motors
Allows mounting with USB pointing up for easy accelerometer calibration
No need for a canopy as all electronics are tucked safely between the ducts
Maximum rigidity where it matters most; connecting the motors to the FC
Easy maintenance, break one duct, replace only the single duct
Recommended Part List
Gemfan Durable 1210 Bi-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft)
Gemfan 1219-3 Durable Tri-Blade 31mm Micro/Whoop Prop 8 Pack (1mm Shaft) - Choose Your Color
HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
FEA optimization test preformed ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 1.6g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 65 Pro was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 65 Pro Whoop Micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 65 Pro Whoop Micro Frame Kit and Meteor65 Pro Whoop frame.
Note: This is designed for prop guards that fit 35mm props like the Meteor65 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
The Pro version has been squished to the max to fit 35mm props with Meteor 65 Pro ducts.
Check out our other Micro frames, and our Fractal Engineering Products!
Features
A variant of the Fractal 65 frame kit
Squished to the max to fit 35mm props with Meteor 65Pro ducts
Maintains 65mm motors distance to meet racing specs
Still fits the camera between the front ducts 1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction
Low-profile camera mount, no props in view, no tilt offset
Low Center of gravity, by bringing the AIO closer to the frame/motors
Allows mounting with USB pointing up for easy accelerometer calibration
No need for a canopy as all electronics are tucked safely between the ducts
Maximum rigidity where it matters most; connecting the motors to the FC
Easy maintenance, break one duct, replace only the single duct
Recommended Part List
BetaFPV Gemfan 1406 Tri-Blade 35mm Micro/Whoop Prop 4 Pack (1mm Shaft) - Choose Your Color
HappyModel EX 0802 19000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel EX 0802 25000Kv Whoop/Micro Motor for Mobula6 HD - CW
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 1.8g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 65 Micro Frame Kit - Choose Your Version
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 75 whoop micro Frame Kit Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Whoop Micro Frame Kit and HappyModel Mobula7 V4 Whoop frame.
Note: You're gonna want to cut ducts from either an NBD, BetaFPV, or Happymodel 75mm whoop frame, and that will serve as your protection for you motor and propellers. This also allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
Check out our other Micro frames, and our Fractal Engineering Products!
Features
75mm diagonal, squished X geometry, for 40mm props
1.5mm Carbon Fiber / Individual Nylon ducts hybrid construction. Cut from Japanese T300 CF sheet
Low-profile camera mount, no props in view, no tilt offset
Low Center of gravity, by bringing the AIO closer to the frame/motors
Allows mounting with USB pointing up for easy accelerometer calibration
No need for a canopy as all electronics are tucked safely between the ducts
Maximum rigidity where it matters most; connecting the motors to the FC
Easy maintenance, break one duct, replace only the single duct
Lightweight, about 21g with HM DiamondF4
Recommended Parts List
HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack - Grey
HappyModel RS 0802 20,000Kv Micro Motor - Choose Version
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 2.1g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
From motorpost to motorpost on this frame, the distance is 84mm.
Are you a whoop racer seeking the best performance with no reliability sacrifice? An FPV pilot wanting a solid frame with fast maintenance? Or after a tough frame to keep you airborne, instead of flimsy nylon frames? If you answer yes to any of those, then the Fractal 75 Pro Max was designed for you! This kit contains all you need to construct your craft - it's compatible with most parts and has a 25.5x25.5mm mount for the AIO and motor mounts for 3xM1.4x6.6mm and 3xM1.6x5.5.
Choose between getting the Fractal 75 Pro Max whoop micro Frame Lite Kit, which does not come with ducts, or grab a combo of the Fractal 75 Pro Max Whoop Micro-frame kit and BetaFPV Meteor75 Pro Whoop Frame.
Note: This is designed for prop guards that fit 45mm props like the Meteor75 Pro. This will serve as your protection and allows you to replace a single duct where-as standard whoop frames need to be fully replaced when a single duct breaks.
The Pro Version has been scaled to the max to fit 45mm props
Check out our other Micro frames, and our Fractal Engineering Products!
Features
A completely new variant of the F75, but this is actually 84mm motorpost to motorpost distance.
The same winning recipe, scaled to fit 45mm props with ducts while keeping the camera up front
Extended camera mount to reduce prop guards in view
Low center of gravity, by bringing the AIO close to the frame/motors
Allows mounting with USB pointed up for easy accelerometer calibration
Easy maintenance, break a duct, replace only the single duct
No need for a canopy as all electronics are tucked safely between the ducts
Approximately 21g using the Happymodel DiamondF4 AIO
Recommended Parts List
Gemfan Ducted 1815 Tri-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color
Gemfan Ducted 1815 Bi-Blade 45mm Micro/Whoop Prop 8 Pack (1.5mm Shaft) - Choose Your Color
HappyModel RS 0802 20,000Kv Micro Motor - Choose Version
HappyModel RunCam Nano 3 800TVL CMOS FPV Camera w/ Holes & Plug for Mobula6
HappyModel Diamond 1S F4 AIO Flight Controller w/ 5A 8Bit 4in1 ESC & 400mW VTX - ELRS SPI
HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
HappyModel CrossF4 F411 1-2S 5A 8Bit AIO Whoop Flight Controller - ELRS 2.4GHz
HappyModel OVX300 25-300mW 5.8GHz U.Fl VTX w/ OpenVTX
FEA optimization test performed, ensuring the stress gets spread out across the whole structure without concentrations
Specifications
CF Weight: 2.21g
Motor Bolt Pattern: 6mm Tri-Mount & 5.5mm Tri-Mount
Stack Size: 25x25mm
Includes
1x Fractal Engineering Fractal 75 Micro Frame Kit - Choose Your Version
The first and only 3″ 1S 18650 quadcopter with foldable, soft-mounted arms and 20+ mins of flight time! Fractal Engineering's foldable take on the 18650 1S 3" long-range trend. Introducing the Wingman, a quad like this is more known for having a powerband more suited for cruising/exploration/surveillance than freestyle/racing. Though this is still very capable of freestyle, as shown in Infinity Loops video on this quad.
Check out our other 3" frames, and our Fractal Engineering Products!
Here's what Fractal has to say about this frame
Have you ever wished you had an extra sidekick quad to help you recover your main machine from a tree?
Or perhaps one you could deploy from the comfort of your car to recon a new spot without the hassle of going out and walking there?
Or maybe just an ultra-compact video rig to give your loved one an excuse to rip a few packs under the pretense of documenting your vacation?
Well, the Wingman is all of that, and much more!
The idea for this frame stemmed from Dave C’s nano long-range, concept -obviously!-
I was immediately hooked on the idea of being able to pop a single, general-purpose 18650 li-ion cell on a quad and cruise around longer than with any of my freestyle rigs
Back then the only frame option was the original 3D printed one
I knew I could greatly improve upon the concept by utilizing carbon fiber, but I also knew that by the time I would be ready to release, I wouldn’t be the only one with a CF arms nano LR
So I decided to up it a notch; I’ve had this idea of folding arms in my head for a while, and the lightweight, low load use case of that format would be the best proving ground for it
Over a year in the making, after many iterations and countless hours of testing and tuning later what is the result?
The first-ever foldable and soft mounted arms in FPV
The major unique feature of this frame kit is obviously the folding arms
And the way it manages to achieve this feature in such an integrated manner is where the whole secret sauce resides
This 3″ 1S format offers the possibility to push incredibly intricate ideas down to an incredibly simple execution thanks to the low prop load
In this case, I’ve chosen to make the top and bottom plates clamped to the standoffs,
While using the same standoffs as pivots for the arms, themselves sandwiched between 2 TPU shims and a nylon spacer to press them down in position
Those TPU shims also serve 2 purposes at the same time; they primarily provide friction for the quick deployment of the arms, while also dampening the junctions
This helps reduce the number of vibrations transmitted to the FPV and HD camera (more on that in a bit) and the FC gyro, enabling smooth footage and easy tuning
Ultra-lightweight, durable and compact design
The spaceframe carbon fiber body was meticulously designed to only keep material where absolutely necessary
This includes protecting all the electronics and maintaining a rigid platform,
While pocketing everything else for lightweight and airflow
Making it only 24g frame only, or 60g ready to fly excl. battery
Quick-release arm mechanism
For being designed around ease of use and quick deployment, I went for a friction fit with a light detent to hold the arms open
Just simply pull the arms out until the detent clicks, and push them back in when you’re done
That means no manual latch, no thumbscrew, no positive lock
This also means that in the event of a crash the arms might fold and you would need to go get it…
…But you’re also more likely to be able to take off again without any damage, as I’ve found during testing that the folding appears to absorb a lot of energy that might have snapped something otherwise
In any event, let that be clear that this remains a stable and soft cruiser above all; you won’t have much fun going bando bashing with it I can almost guarantee it
To sum it up
just a great tool to always have with you, just so many uses for it
Toss it in your bag when you’re going on vacation for drone videos (also a great excuse for your wife to bring a quad)
Use it to recon new spots to rip without going out of the car (walking? like with your legs?)
Search and rescue! Take advantage of the long flight time to look for a lost quad (I hope you find it brother/sister)
Attach a string to the back, fly around that branch you got your main quad stuck on, bring it back and give it a good tug (watch your head)
Or even get that whoop you got stuck on that roof (I know you could just climb up the gutter but come on it’s 2022)
Guerilla dive! pull it out of pocket, deploy it in a second, rip that huge building tower (you know which one), fold it back in your pocket and bail
Or simply just cruise around for a relaxing chill flight, perhaps to wind down after a hard charger sesh (if you got the patience for it)
… or whatever else you want it to be!
Includes
1x Fractal Engineering Fractal Wingman 1S 18650 Foldable 3" Micro Frame Kit
1x Top plate
1x Bottom plate
2x Front plates
4x Arms
1x 18650 Tray
4x M2 x 10mm alu standoffs
4x M4 x 6mm nylon spacer
10x M2 x 5mm steel screw (for the standoffs)
4x M1.7 x 5mm steel self-threading screw (for the 18650 Tray)
1x TPU cam holder
2x TPU shim set
4x M2 x 10mm steel screw (for the stack)
10x M2 nylon nuts (for the stack)
10x M2 x 4mm socket screws (for the motors)
Legacy 2.0 firmware available here
Very small, lightweight, minimal, yet highly functional! The FRSKY XM+ SBUS Receiver is perfect for FPV racing. It has as good of range as any other FRSKY receiver on the market, with the added benefit of diversity antennas, while also being the smallest and most lightweight (1.6g) option. If you do not use FRSKY telemetry, or you don't know what that is, then this is the receiver for you!
Check out this link for firmware updates or finding older firmware.
Click here for replacement antennas.
Check out all our RC receivers, and all our FrSky products!
Specifications
Number of Channels: Up to 16CH from SBUS(CH1~CH15 for PWM, CH16 RSSI for FC
Operating Voltage Range: 3.7~10V
Operating Current: 30mA@5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware Upgradeable
Compatibility: FrSky D16 mode
Dimension: 21/5x12x3.5mm(LxWxH)
Antenna Connector: IPEX4
Weight: 1.6g
Includes
1x FrSky XM+ SBUS 2.4GHz Mini Receiver
This monitor from FYS is a perfect addition to your FPV setup. Featuring diversity, this monitor can pick up 2 independent signals and display the best one.
Check out the rest of our FPV monitors!
Specifications
Size: 4.3"
Brightness: 500Lux
Aspect Ration: 16:9
Receiver: Diversity
Frequency: 5.8GHz
Channels: 40
Video In: 3.5mm Port
Auto Scan: Yes
DVR: Yes
Charging port: Micro USB, 5V
Antenna Connector: RP-SMA
Dimensions: 113x79x14mm
Weight: 154g
Includes
1x FYS 40CH 5.8GHz Diversity FPV Monitor w/ DVR
The revolutionary Gemfan 1170-3 Cinelifter prop 11" tri-blade prop created in collaboration with @Ellis Van Jason and @Josh Enriques offers superlative performance & unique flight characteristics even under heavy loads. The narrow surface ensures lightness & improved drone airflow. The propeller's high pitch is an unprecedented innovation, a 7.0 pitch impeccably designed and meticulously tested on both bench and FPV Propellers Wind Tunnels. Its new plastic polymer mix provides durability, allowing it to withstand loads & deliver over 5Kg of thrust. Cinelifters have revolutionized the FPV drone industry, providing new opportunities to pilots. This prop is the best tool for the job.
Check out all our 8" & above props, and all our Gemfan products!
Specifications
Inch: 11in
Pitch: 7in
Weight: 27.7g
Mount: 1.5mm
Recommended Motor: 3220
Prop Disk Diameter: 279.4mm
Center Thickness: 9mm
Max Prop Width: 24mm
Materials: Glass fiber nylon
Includes
1x Gemfan 1170 Reinforced Glass Fiber Nylon Tri-Blade 11" Prop 2 Pack - Black
Welcome a new design in FPV drone racing propellers the Gemfan Hurricane 51499! Designed with racing in mind the 51499 propeller stays steady at high speed runs and has a fast response going through those low gates and split s drops! The Gemfan Hurricane 51499 is extremely durable and easy to bend back after a crash so no need to worry about breaking a prop quickly stay in the air longer. Get yours today!
Check out all our 5" Props and all our Gemfan products!
Specifications
Hub Thickness: 7mm
Material: PC Polycarbonate
Length: 5.1
Pitch: 49.9
Includes
4x Gemfan Hurricane 51499 Durable Tri-Blade 5" Prop (2CW, 2CCW)
A budget and user-friendly charger for all your FPV needs!
The Imars Mini Charger, from Gens Ace, has been designed specifically for Gens Ace G-Tech smart batteries while also compatible with non-smart batteries.
It is the first member of the Gens ace G-Tech Smart Eco, when the Gens ace G-Tech battery is connected to the Imars Mini charger, the charger will automatically identify the battery type, voltage through the smart balance connector, and charging current recommended by the battery manufacturer. The charger will start charging in 5 seconds automatically after G-Tech smart battery is connected.
For non-smart batteries, it's necessary to manually select the battery type and the required working mode to get it started. The charger can intelligently adjust the charging current according to the charging voltage flow of the battery.
Check out our other battery chargers and accessories!
Features
Charges 2-4S LiPo, LiHV, LiFe, and 2-12S NiMH batteries.
Intelligently recognizes G-Tech smart battery info through an IC chip for safe and easy charging.
Automatic storage function, it's the smallest charger with auto storage.
New interface design and increased balance connector durability.
Small & lightweight, portable design.
Specifications
Max. Charge Power: 60W
Charge Current: 1-5A, Max. 5A(Auto Adjustment)
Max. Storage Power: 3W discharge, 60W charge
Input Voltage: 5-20V
Max. Input Current: DC 3A
Balance Current: 0.4A/Cell X 2
Input Port: QC/PD/BC1.2/USB-C V1.4/SDP/CDP/DCP/Apple 5V/2.4A(Does not support 5V/1A adapter input)
Abnormal Battery Voltage Alarm: Yes
Supported Battery Types: Lipo/LiHv/LiFe(2~4S), NiMH(2-12S)
Working Temperature: 0℃~40℃
Storage Temperature: -20℃~60℃
Dimension: 85x55x21mm
Net Weight: Approx. 64g
Includes
1x GensAce IMARS Mini G-Tech 60W 5A DC Smart Charger
Taking your drone photography to the next level, the new series Cinebot30, take you to the real world, shooting extreme footage.
Cinebot30 is a new generation of Cinematic FPV drone developed by GEPRC team. The high-strength 7075 aircraft-grade aluminum alloy bracket for FPV camera escort, the combination of classic engineering and aesthetics. The newly polished gimbal damping module can easily fix high-frequency vibration and jello issues. It can be mounted with GEPRC Naked GoPro Hero 8 and GoPro Black Bones, Insta 360 GO2 and other cameras. The image is stable and clear, and it’s easy to film.
Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!
Cinebot30 will be equipped with a powerful 1804 motor with optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmx3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations. Finely polished frame design, only 6 screws need to be removed to separate the aircraft top plate and protection frame. Easy to cope with the urgent need to replace the accessories, at any time to restore the state.
Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Design that combines engineering and aesthetics.
Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts.
Selected high-toughness and impact-resistant PC material for injection molding.
Aviation 7075 aluminum alloy camera mounting bracket and fuselage aluminum column.
Propeller guard embedded ring Cob light strip, carefully tuned light effect. Color brightness in the day and night can be clearly displayed.
The newly developed gimbal shock absorption structure can disintegrate high frequency jitter and jello effect. Easily carry a variety of action cameras.
Powerful 1804 motor, surging torque to deal with ultra-low altitude flight at will.
With the new GEP-F722-45A AIO V2, stable performance, more secure flight
Four kinds of FPV system with the program, choose to belong to your first-person view
Tuned by GEPRC professionals, delicate and silky flying feel
Specifications
Input Voltage: 3-4S
Wheelbase:127mm
Isolation Plate:2mm
Main plate:3mm
Bottom plate:1.5mm
Motors: SPEEDX2 1804-3450KV
Propellor: HQ prop T76mmx3 propeller
VTX: GEPRC RAD 1W
Antenna: Peano 5.8G 110mm RHCP MMCX Antenna
Camera: Caddx ratel 2
Weight: 206.4g
GEPRC GEP-F722-45A AIO
Model: Cinebot30 HD Nebula PRO Quadcopter
Gyro: BMI270/42688 gyro/accelerometer(SPI)
OSD: Yes
ESC Connections: Yes
Firmware: GEP-F722-45A AIO
BEC: 5V 1A
Current Sensor: Yes
Buzzer: no
Barometer: No
Input Voltage: 2-4S LiPo
MCU: STM32F722RET6
IMU: ICM-42688-P
Stack Size: 25x25mm
Dimensions: 32x32xmm
Weight: 8.8g
Includes
1x GEPRC BNF CineBot30 4S 3" Analog Cinewhoop - Choose Version
2 x HQProp T76MM（pair）
1 x Battery strap M15x200mm
1 x Battery strap M15x220mm
2 x Battery Silicone Pads
1 x Set of screws
1 x Set of screwdrivers
1 x GoPro camera mount holder
1 x Set of screws
1 x Set of screwdrivers
1 x Antenna fixed tube
Since DJI released the O3 AIR Unit FPV high-definition video transmission system, the GEPRC team has followed closely to make the latest set of the O3 AIR Unit system, the Cinebot30 HD O3 AIR Unit version. The Cinebot 30 is a new generation of cinematic FPV drones developed by the GEPRC team.
The aluminum parts of the camera are still made of high-strength 7075 aircraft-grade aluminum alloy materials. The TPU shock-absorbing pad is designed on the bracket structure, which can excellently isolate the high-frequency vibration of the fuselage so that the camera can still obtain jelly-free high-definition images during high-speed flight The installation of the video transmission has also designed an assembly scheme, which allows the O3 video transmission to be completely installed inside the fuselage without affecting the Type-C USB data cable connected to the Air Unit to read video data. O3 Air Unit is currently the most advanced FPV system on the market. It can transmit 1080P 60fps real-time images, and can also record up to 4K 60fps images with an anti-shake effect at the same time.The upgraded video transmission system also combines market feedback to upgrade the gimbal top plate of the fuselage, which is compatible with the camera base fixed by 4-hole screws, so that Cinebot30 can mount a full-sized GoPro camera very well, and the battery life can reach 5 minutes and 30 seconds. However, the GEPRC team recommends flying with Naked GoPro 10, with a battery life of up to 10 minutes and 30 seconds.Adopts high-strength one-piece injection-molded propeller guard and high-toughness and impact-resistant PC material for injection molding. A ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. High-strength grain-cut carbon fiber sheet, the overall strength of the fuselage is upgraded again!Cinebot30 will be equipped with a powerful 1804 motor with an optimized motor magnetic circuit and surging torque, which can easily cope with ultra-low altitude shooting. With HQ prop T76mmX3 propeller, it gets the lowest noise effect in its class. Using GEP-F722-45A AIO v2 flight controller, higher performance redundancy, and easy handling of unexpected situations.Tuned by GEPRC professionals, the Cinebot30 is a Cinematic FPV that performs both indoor and outdoor flights equally well. The Cinebot30 explores endless possibilities for your drone shots!
Features
Adopts the most advanced O3 Air Unit FPV digital video transmission system on the market
Video transmission with high-definition anti-shake 4K 60fps ultra-high resolution video quality
The highest bit rate is 50MBPS, the delay is as low as 30 milliseconds, and the highest image quality is 1080P 60FPS
Upgraded the top plate of the fuselage gimbal, compatible with the camera base fixed by 4-hole screws, and supports mounting a full-sized GoPro camera for flight
The camera aluminum mechanism is designed with TPU shock absorption, which can effectively eliminate the image jello caused by the vibration of the body
The ring-shaped Cob light strip is embedded in the propeller guard, and the light effect is carefully tuned. Color brightness can be clearly displayed in day and night
Selection of high-quality high-toughness, impact-resistant PC&PET material injection molding
Powerful 1804 motor, surging torque to cope with ultra-low altitude flight
Quick-disassembly design, only need to remove 6 screws to upgrade or replace parts
With the new GEP-F722-45A AIO V2, the performance is stable and the flight is more secure
Tuned by GEPRC professionals, delicate and silky flying feel
Specifications
Model: Cinebot30 HD O3 Quadcopter
Brand: GEPRC
Frame: GEP-CT30 O3
Wheelbase:127mm
Isolation Plate:2mm
Main plate:3mm
Bottom plate:1.5mm
FC: GEP-F722-45A AIO V2
MCU: STM32F722RET6
IMU: ICM-42688-P
VTX: DJI O3 Air Unit
Video resolution: 4K@50/60fps, 2.7K@50/60/100/120fps, 1080p@50/60/100/120fps
Camera: DJI O3
Propeller: HQ prop T76mmx3 propeller
Antenna: DJI O3 Antenna
Charge connector: XT60H-M
Motor: SPEEDX2 1804-2450KV（6S Version）/ SPEEDX2 1804-3450KV（4S Version）
Weight: Nebula Pro version 222.5g / Avatar version 221g / Analog version 209.2g / Link Wasp version 222.5g / O3 version 234.7g (excluding battery, the above are TBS Nano RX version)
Receiver: PNP, Frsky R-XSR, TBS Nano RX, ELRS 2.4G
Recommended Battery: LiPo 4S 1100mAh-1300mAh (4S Version) / LiPo 6S 850mAh-1100mAh(6S Version)
Includes
1x Cinebot30 HD O3 Quadcopter
2x HQProp T76MM（pair）
1x Battery strap M15x200mm
1x Battery strap M15x220mm
2x Battery Silicone Pads
1x Set of screws
1x Set of screwdrivers
1x GoPro camera mount holder
1x Set of screws
1x Set of screwdrivers
1x Antenna fixed tube
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market.
The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life.
It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras.
Find the recommended 4S 450-750mAh batteries here!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect.
Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning.
2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting.
SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried.
Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted.
The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible.
Specifications
Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz
Frame: GEP-CL20
Wheelbase: 100mm
Gimbal plate: 2.0mm
Top plate: 2.5mm
Bottom plate: 1.5mm
FC system: GEP-F411-35A AIO
MCU: STM32F411CEU6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 35A
VTX: GEPRC 5.8GHz@600mW
Camera: Caddx Ratel2
Antenna: GEPRC Peano 5.8G RHCP MMCX
Motor: GR1303.5 5500KV
Propeller: EMAX Avan Micro 2×2.4×4
Receiver: ELRS2.4G
Recommended battery: LiHv 4S 450mah-660mah
Flight time: 4-6min
Includes
1x CineLog20 Analog
2x 2-inch propellers (pairs)
1x Naked GoPro Base
2x M15×150mm battery strap
2x Battery Silicone Pads
2x EVA Landing Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x Antenna fixed tube
1x 4S Naked GoPro power cable (with balanced terminal head)
2x EVA damping rings of guards
1x TBS Antenna mount (Vertical Type)
1x TBS Antenna mount (Horizontal Type)
1x TBS Antenna printed parts
The screw package includes:
3x M2×12mm cup head screws
2x M2×5mm round head screws
1x M2×8mm round head screw with pad
3x M2×7mm round head screws
2x M2×8mm round head screws
2x M2 iron nuts
1x self-clinching nut
For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog four mainstream video transmission systems on the market.
The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 AIR Unit shooting, which can achieve an excellent anti-shake effect. The O3 Air Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life.
It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras.
Find the recommended 4S 450-750mAh batteries here!
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect.
Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning.
2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting.
SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried.
Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted.
The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible.
Specifications
Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz
Frame: GEP-CL20
Wheelbase: 100mm
Gimbal plate: 2.0mm
Top plate: 2.5mm
Bottom plate: 1.5mm
FC system: GEP-F411-35A AIO
MCU: STM32F411CEU6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 35A
VTX: Link
Camera: RunCam Wasp
Antenna: GEPRC Peano 5.8G LHCP U.FL
Motor: GR1303.5 5500KV
Propeller: EMAX Avan Micro 2×2.4×4
Receiver: PNP (built-in DJI receiver), ELRS2.4G
Recommended battery: LiHv 4S 450mah-660mah
Flight time: 4-6min
Includes
1x CineLog20 HD Wasp
2x 2-inch propellers (pairs)
1x Naked GoPro Base
2x M15×150mm battery strap
2x Battery Silicone Pads
2x EVA Landing Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x Antenna fixed tube
1x 4S Naked GoPro power cable (with balanced terminal head)
2x EVA damping rings of guards
1x TBS Antenna mount (Vertical Type)
1x TBS Antenna mount (Horizontal Type)
1x TBS Antenna printed parts
The screw package includes:
3x M2×12mm cup head screws
2x M2×5mm round head screws
1x M2×8mm round head screw with pad
3x M2×7mm round head screws
2x M2×8mm round head screws
2x M2 iron nuts
1x self-clinching nut
Experience unrivaled performance with the GEPRC CineLog35 V2 6S 3.5" Cinewhoop. This powerful model features an analog & micro cam, as well as ELRS 2.4GHz technology, for streamlined flight capabilities and less chance of a fail safe. Fly with confidence as you capture flawless footage with every launch.
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
New appearance design, strengthening carbon plate, hollow design, injection protection frame, noise reduction design, flight safety, silent.
Adopts the GEP F722-45A AIO V2 high performance flight controller.
SPEEDX2 2105.5 motor with HQ DT90 propeller, stable power output, and smooth flight feel.
Power cable using XT60E1-M plug and carbon plate integrated design, convenient application.
Battery installation method using a tie with 7075 aluminum parts fixed, solid and stable.
Carefully tuned 3.5-inch cinematic FPV quad with flexible and delicate flight feeling.
Pre-Installed with a M8U GPS
Specifications
Model: Cinelog35 V2 Analog
Frame: GEP-CL35 V2
Wheelbase: 142mm
Gimbal Plate: 2.0mm
Top Plate: 3.5mm
Bottom Plate: 1.5mm
FC system: GEP-F722-45A AIO V2
MCU: STM32F722RET6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
ESC: 8Bit 45A
VTX: GEPRC RAD 1W(UFL)
Camera: Caddx Ratel2
Antenna: GEPRC Peano 5.8 RHCP UFL
Motor: SPEEDX2 2105.5-2150KV (6S)
Propeller: HQProp D-T90MM
GPS: GEP-M8U
Receiver: ELRS2.4G
Weight: 262g
Recommended battery: LiPo 1050mah-1300mah
Flight time: 5′00″ - 8′ 30″
Includes
1x GEPRC BNF CineLog35 V2 Analog 6S 3.5" Cinewhoop - ELRS 2.4GHz (GPS)
2x HQProp D-T90MM（2 pairs）
2x M20 x 250mm battery strap
2x Battery Silicone Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x L-shaped screwdriver (2mm)
1x L-shaped screwdriver (3mm)
1x M5 wrench
1x plastic tweezers
1x Antenna fixed tube (pair)
1x Keychain
1x GP Camera Mounting Base
1x Naked GP Camera Mounting Base
1x Antenna Mounting Base
The GEPRC team has an amazing history of pushing boundaries and redefining standards in long-range FPV. Introducing the Crocodile75 V3: designed for comfort and stability, with a novel appearance, O3 Air Unit and special cooling components for efficient cooling, SPAN G50A BLHeli_32 4IN1 ESC, and 2806.5 1350KV motor and expertly tuned performance. Experience the passionate flight of the Crocodile75 V3! The battery plug is integrated with the fuselage for convenient application. The overall performance of Crocodile75 V3 has been carefully and strictly tuned by the GEPRC team to bring the most passionate flying experience for pilots.
Check out our other pre-built quads, as well as the rest of our GEPRC selection.
Features
Adopt a novel appearance design, strengthen the fuselage structure, and reduce the impact of fuselage vibration on the gyroscope sampling data.
Equipped with SPEEDX2 2806.5 1350KV motor and HQ7.5×3.7×3 with sufficient power and high efficiency.
Upgrade the ESC to SPAN G50A BLHeli_32 4IN1.
Add protective side panels to effectively protect the electronic control system from instability caused by sand and dust pollution
The integrated design of the battery plug and the body simplifies the power-on operation, simplicity and beauty.
Equipped with O3 Air Unit and added special heatsink, excellent heat dissipation, to avoid O3 Air Unit overheating and stop recording.
The Crocodile75 V3 has a lengthier fuselage, can be mounted with Lipo 6S 3300mah-4500mah or Lion 6S 6000mah battery for flight.
Perfect match for 7-inch or 7.5-inch propellers
Specifications
Specifications
Model: Crocodile75 V3 HD O3
Frame: GEP-LC75 V3
Wheelbase: 342mm
Top plate: 2.5mm
Bottom plate: 3.0mm
Arm plate: 6.0mm
Splint plate: 2.5mm
FC: SPAN F722-BT-HD V2
ESC: SPAN G50A BLHeli_32 4IN1
MCU: STM32F722RET6
Gyro: ICM 42688-P
OSD: Betaflight OSD w/AT7456E chip
VTX: O3 Air Unit
Camera: O3
GPS: GEP-M8U
Antenna: Momoda 5.8G LHCP RP-SMA x2
Motor: SPEEDX2 2806.5 1350KV
Propeller: HQProp7.5x3.7x3
Weight: 628.5g
Receiver: GEPRC ELRS 2.4G
Recommended battery: Lipo 6S 2600mah-4200mah / Lion 6S 6000mah
Flight time: 12-30 min
Includes
1x GEPRC BNF Crocodile75 V3 HD LR 6S 7" Long Range Quad w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz (GPS)
4x HQProp7.5x3.7x3
2x M20x250mm battery straps
2x Battery Silicone Pads
1x Set of screws
1x L-shaped screwdriver (1.5mm)
1x L-shaped screwdriver (2mm)
1x L-shaped screwdriver (3mm)
1x M5 wrench
1x GEPRC Keychain
1x GP Camera Base
Does not come with naked Gopro mount. Please refer to the includes list at the bottom of the listing for all included items.
The classic CL25 Frame, designed by the GEPRC team, has been upgraded. They've redesigned the shock absorption structure of the camera mount, eliminated the jelly coming from the FPV camera, and you can now use 3, 4, and 5 damping rings according to the flight state to obtain the best stability in vibration and noise. The CL25 can be used for Vista HD digital image transmission system or Analog image transmission system. The center of gravity of the quadcopter is in the middle,
Check out all our DJI-compatible frames, electronics, and accessories as well as our whole GEPRC product line!
Specifications
Dimensions: 109mm
Frame Style: Cinewhoop
Top Plate: 2.5mm
Bottom Plate: 1.5mm
Bottom Plate(camera): 2mm
Stack Size: 26.5x26.5mm
Motor Mount: 9x9mm (compatible with 1105/1204/1206 motors)
Camera Mount: 14-20mm (Nano and Micro-sized)
Weight: 47.8g
Recommended:
Motor: BetaFPV 1404 4500Kv Micro Motor 4 Pack
FC/ESC: GEPRC F411 2-6S AIO Flight Controller w/ 35A 4in1 ESC
Prop: Gemfan D63 Ducted Durable Tri-Blade 2.5" Cinewhoop Prop 8 Pack
LiPo: RDQ Series 14.8V 4S 650mAh 80C LiPo Micro Battery
Includes
1x Top plate 2.5mm
1x Bottom plate 1.5mm
1x Bottom Plate (Camera)1.5mm
4x (M2x3.5x25mm) Aluminum posts
2x (M2x3.5x8mm) Aluminum posts
28x (M2x6mm) YFS Round head screws
2x (M2x8mm) YFS Round head screws
4x (M2x12mm) YFS countersunk head screws
16x (M2x2mm) Nylon Nuts
4x (M2x18mm) YFS countersunk head screws
5x Damping Rings
1x (19x19mm) Mount of camera
1x (14x14mm) Mount of camera
1x 3D print part of XM antenna
1x 3D print part of TBS antenna
1x Naked Camera Mount (This is just the base, NOT the actual camera case)
2x Batteries pads
2x EVA Landing pads
4x 2.5-inch Guards
1x EVA Damping Ring of Guard
2x Antenna Tubes
2x Batteries straps (M15x150mm）
GEPRC Peano antenna is a 5.8G optimized antenna for FPV quad. The antenna has good gain performance and very compact. Working frequency range is 5600-5950 Ghz, with LHCP and RHCP options for multi-player competition. Peano 5.8G antenna also has a variety of connector options. Every antenna has been tested strictly before leaving the factory to ensure good performance.
Check out the rest of our antennas, as well as the rest of our GEPRC selection.
Features
Compact and light-weight design, high quality ABS case for good protection and nice appearance.
Options of LHCP and RHCP.
Manufactured and tested to highest standards
Easy to install, multiple connectors and length options.
50mm Length from end of tube to connector
Specifications
Frequency Range: 5600-5950MHz
Polarization: LHCP/RHCP
Gain: 2.5DBi
SWR: ≤1.5
Input Impedance: 50Ω
Radiation Efficiency: 98%
Connector: MMCX 90
Weight: 1.6g~1.8g
material: ABS
color: transparent grey
Includes
2x GEPRC Peano 5.8G Antenna MMCX 90 - Choose Version
GEPRC Peano antenna is a 5.8G optimized antenna for FPV quad. The antenna has good gain performance and is very compact. The working frequency range is 5600-5950 Ghz, and is designed as RHCP antenna. Peano 5.8G antenna comes with a U.FL connector. Every antenna has been tested strictly before leaving the factory to ensure good performance.
Check out the rest of our antennas, as well as the rest of our GEPRC selection.
Features
Compact and light-weight design, high quality ABS case for good protection and nice appearance.
Manufactured and tested to the highest standards
Easy to install, multiple connectors and length options
Specifications
Frequency Range: 5600-5950MHz
Polarization: RHCP
Gain: 2.5DBi
SWR: ≤1.5
Input Impedance: 50Ω
Radiation Efficiency: 98%
Connector: UFL
Weight: 1.6g~1.8g
material: ABS
color: transparent grey
Length: 110mm
Includes
1x GEPRC Peano 5.8GHz 110mm U.FL Antenna 2 Pack - RHCP
When you're chasing the ultimate speed in the FPV racing arena, the GepRC Racer 5" Racing Frame Kit is the perfect choice. This frame is specially designed for the competition. Combining 7075-T6 aviation aluminum alloy splint with high-grade T700 carbon plate CNC processing, this frame is beyond solid. The flight controller attaches easily to 20x20mm/25.5x25.5mm/30.5x30.5mm mounting holes, and motors attach to the 16x16mm.
When the conventional FPV drone cannot satisfy the pursuit of speed in FPV racing, then this is the frame for you!
Choose between having the aluminum plate colored with red or silver accents!
Be sure to check out all our 5" frames, and our GEPRC products!
Specifications
Model: RACER FPV Frame
Frame: GEP-RACER Frame
Dimensions: 175mm×173mm
Wheelbase: 208mm
Top plate: 2.0mm
Aluminum plate: 2.0mm
Bottom plate: 2.0mm
Arm thickness: 5.0mm
Aluminum column size: M3x6x24mm
FC mounting hole: 30.5mmx30.5mm/25.5mmx25.5mm/20mmx20mm
VTX mounting hole: 20mmx20mm
Motor mounting hole: 16mmx16mm
Camera installation space: 14mm
Propeller: 5 inches
Weight: 78g ± 2g
Includes
1x Top plate
1x Bottom plate
1x Aluminum plate (Red or Titanium)
1x Camera mount
1x VTX antenna mount
1x Shark fin print
4x M3x6x24mm aluminum column
2x 20x250mm battery cable ties
2x Battery anti-skid pads
1x Screw pack
1x L-shaped screwdriver 1.5mm
1x L-shaped screwdriver 2mm
Introducing... the GEPRC SMART 16 Freestyle Frame Kit!
The GEPRC Smart 16 1.6" Nano Freestyle Frame is a tiny, lightweight freestyle FPV addition to the GEPRC Phantom series. The SMART 16 continues the consistent lightweight design concept of the Phantom series. The 1.5mm carbon fiber arm, with a 1mm top plate, creates a balance point that is maintained between the strength of the fuselage and the weight of the whole drone which allows it to be lightweight and tough at the same time. The M1.4 Motors mounting holes can be used to install small 3-hole brushless motors to reduce the weight of the body. Good arm width contributes to high durability. This design is great for freestyle flying, with no props in view!
Thanks to the 3D printed parts, the frame weighs only 8.5g, saving a lot of overall weight. The independent battery compartment is designed to stick the battery on top and below the drone making it very convenient and fast to replace batteries.
Check out our other Micro frames And our whole GEPRC product line!
Specifications
Frame Style: Toothpick
Top plate thickness: 1.0mm
Bottom plate thickness: 1.5mm
Camera plate thickness: 1.0mm
Stack Size 16x16mm
Motor Mount: 6mm Tri 08xx
Camera Mount: 14mm Nano
Weight: 8.5g (including 3D prints)
Recommended:
Motor: GEPRC SPEEDX2 0803 11000Kv Micro Motor
AIO: GEPRC F4 V1.4 2-4S AIO Flight Controller
Prop: HappyModel Gemfan 1610 Bi-Blade 40mm Micro/Whoop Prop 4 Pack
LiPo: RDQ Series 350mah 2S 50C/100C 7.6V HV XT30 Micro Battery
Includes
1x GEPRC SMART 16 1.5mm Bottom Plate
2x GEPRC SMART 16 1mm Camera Plate
1x GEPRC SMART 16 1mm Top Plate
2x 120mm LiPo Strap
1x 3D Printed Part Set
1x Screwdriver Set
1x Hardware Set
2x Battery Pad
GEPRC SPEEDX2 0802 brushless motor, specially developed for Micro and Whoop FPV, SPEEDX2 motors are enough to meet your needs. GEPRC SPEEDX2 0802 motors have good heat dissipation, lightweight design, and advanced material technology, perfect for Micro and Whoop applications.
Specifications
Check out all our motors and our GEPRC selection!
Specifications
Kv: 17000kv
Input Voltage: 1S
Configuration: 9N12P
Shaft Diameter: 1mm
Mounting Pattern: Φ6mm, 3x M1.4
Wire Dimensions: JST-1.25, 33.5mm
Weight: 2g (w/ wire)
Includes
1x GEPRC SPEEDX2 0802 Micro Motor
The GEPRC SPEEDX2 0803 brushless motor is specially developed for Micro and Whoop FPV. These SPEEDX2 motors are enough to meet your needs. The 0803 motors have good heat dissipation, lightweight design, and advanced material technology, perfect for Micro and Whoop FPV applications.
Specifications
Check out all our motors and our GEPRC selection!
Specifications
Kv: 11000
Input Voltage: 1S
Configuration: 9N12P
Shaft Diameter: 1mm
Mounting Pattern: Φ6mm, 3x M1.4
Wire Dimensions: JST-1.25, 33.5mm
Weight: 2.4g (w/ wire)
Includes
1x GEPRC SPEEDX2 0803 Micro Motor
The SPEEDX2 2107.5 brushless motors are the second-generation GEPRC motors designed from scratch. GEPRC SPEEDX2 2107.5 motor is lightweight, has good heat dissipation, and is made of customized high-quality materials. Thanks to the amazing throttle control and advanced engineering design, these motors provide a super smooth flying experience while being super powerful, highly durable, and crash-resistant. SPEEDX2 2107.5 motors are perfect for freestyle and racing FPV pilots. Suitable for a 5-inch frame.
Check out our vast brushless motors selection, and our GEPRC selection!
Features
High-efficiency and smooth
Perfect for Freestyle and Racing FPV
Motor dynamic balance, stable operation
Best for a 5-inch frame
Specifications
Model: SPEEDX2 2107.5
Kv: 1960KV/2450KV
Configuration: 12N14P
Stator Diameter: 21mm
Stator Height: 7.5mm
Shaft Diameter: Φ4.0mm
Size: Φ26.83x30.85mm
Rotor: N52H ARC
Weight: 29.5g
Target: Freestyle & Racing FPV
Includes
1 x SPEEDX2 2107.5 motor
1 x M5 Nut
5 x M3x8 Screw
5 x M3x10 Screw
The SPEEDX2 2809 motor is created with 7-8" FPV drones in mind. It's equipped with Kawasaki 0.2MM silicon steel sheets and N52SH magnetic steel for 30% better heat-resistance. A clean black base with red accents, for a nice power full quad motor.
Check out all our motors and our GEPRC selection!
Features
Using 7075 aviation aluminum alloy, high-precision CNC integrated
Dark appearance with red accent
The rotor edge structure conforms to the load-bearing mechanical design and has strong impact resistance.
Adopt high-quality N52SH magnetic steel to prevent high-temperature demagnetization.
Specifications
Model: SPEEDX2 2809 Motor
KV: 1280
Configuration: 12N14P
Magnet: N52SH ARC
Rotor material: 7075-T6 aviation aluminum alloy
Stator diameter: 28mm
Stator height: 9mm
Output shaft diameter: Φ5mm
Dimensions: Φ36.04mm x 36.53mm
Outlet specification: 18AWG 250mm
Rated voltage: 25.2V 6S（LiPo）
Maximum power (W): 1148.9
Maximum current (A): 49.35A
Mounting hole: 19x19mm (M3)
Color: red and black
Weight: 71.4g
Applicable models: 7-8 inch long range FPV/7-8 inch X8 models
Include
1x GEPRC SPEEDX2 2809 1280Kv Motor
1x Motor Hardware
GEPRC Goggles pad is crafted with memory foam and skin-friendly nylon mesh fabric for a cozy fit that's compatible with DJI Goggles 2 and Integra. The padding is comfortable to wear and fits a variety of face shapes.
Check out our other FPV goggles and accessories, as well as the rest of our GEPRC selection.
Features
The sponge foam padding is made of memory foam and skin-friendly nylon mesh fabric, which gently fits the face and is comfortable to wear. It can provide extra cushioning and support to reduce the user’s discomfort when wearing for a long time. This padding can better fix the goggles on the head and ensure the visual stability during the flight.
Specification
Model: GEPRC Sponge Foam Padding for DJI Goggles 2
Material: memory foam, skin-friendly nylon mesh fabric
Weight: 12.8g
Includes
1x GEPRC Sponge Foam Padding for DJI FPV Goggles 2
1x Velcro
1x Sticker
Introducing the GEPRC Taker F411 8bit 12A AIO Flight Controller, the perfect addition to your mini FPV drone. It is packed with features like ICM-42688-P gyro, 12A ESC support, 2-4S power, and a built-in black box with 16MB flash memory for easy parameter adjustments. Best of all, this AIO comes with a built-in ELRS 2.4GHz receiver with a U.FL connector. Get ready for smooth and precise races and freestyles with this highly-integrated powerful all-in-one flight controller!
Check out all our Whoop/AIO Flight Controllers, as well as the rest of our GEPRC selection.
Features
Bluejay 12A ESC, support 2-4S battery, continuous current 12A, peak current 13A, built-in ammeter
SPI ELRS 2.4G receiver
Using STM32F411 FC, the flight control is running stably
Using IMU: ICM42688P gyroscope, 8K sampling rate
Support buzzer and LED light function
With 25.5mm x 25.5mm mounting holes
Specifications
Model: TAKER F411 8Bit 12A AIO
MCU: STM32F411
IMU: ICM42688P
Firmware target: GEPRC_F411_SX1280
OSD: BetaFlight OSD w/ AT7456E chip
UART Ports: R1 T1\R2 T2
Reverse Port: NR2
Buzzer: YES
LED: YES
USB Port: Micro USB
ESC MCU: BB21F16G
Black Box: 16Mb onboard flash memory
Continuous Current: 12A
Peak Current: 13A
Input: 2-4S
ESC Protocol: Dshot300, Oneshot, Multishot
Current Meter: 210
ESC Firmware: G-H-30 – Bluejay, 0.16, 48kH
Size: 31.2 x 31.2mm Board
Mounting holes: 25.5mm x 25.5mm hole, M2 hole
Weight: 7g
ELRS Connector: U.FL
Includes
1x GEPRC Taker F411 2-4S AIO Whoop/Toothpick w/12A 8bit 4in1 ESC - ELRS 2.4GHz (SPI)
1x XT30-5.5CM-20AWG power cable
8x M2x6.5mm FC damping grommets (4 each in red/black)
1x 35V220UF capacitor
5x Self-tapping screws (M1.4X5)
1x Instruction manual
HAKRC bring us another serious contender in whoop sized AIO boards. The HAKRC F7220 2-6S BL-Heli32 bit ESC AIO Flight Controller. This ultra-powerful 20x20mm board is capable of handling the most demanding of tasks, including tons of power delivery such as pad options for 5V/3A & 10V/2.5A BEC delivering unbeatable performance and reliability. Give your quad those high quality parts for a better longevity for your quads.
Check out our other AIO boards and our other HAKRC products for sale at RaceDayQuads!
NOTE:
After upgrading the firmware of HAKRC F7220 AIO, the sensor direction needs to be changed
1. Connect FC to BF and select “configuration” page.
2. In the “flight control and sensor direction” column on the right side of the configuration page, change the first gyroscope to cw 90
3. on the setup page. Calibrate the flight control accelerometer and reset the z-axis and test whether the flight control roll, pitch and yaw are consistent with the BF feedback direction.
4. please check and make safety preparations before takeoff in an open or relatively safe place to test the flight feasibility.
5. If you use the DJI remote control and the DJI FPV glasses, open the serial data receiver Port 2 and MSP Port 6, as shown below:
Features
The PCB adopts high-end 8-layer 2oz thick copper skin, which has stronger over-current capability and good heat dissipation
MOS adopts imported 40V high current resistance MOS, long life and strong load capacity
Industrial grade LDO, high temperature resistance
High-quality Japanese Murata capacitors, strong filtering performance
Size: 40x30mm (20mmx20mm mounting hole)
Product net weight: 10g
Specifications
Flight Controller
Input Voltage: 2S-6S
MCU: STM32F722RET6
IMU: ICM42688
OSD: AT7456E
Black box: 16M
UARTs: 5
Barometer: integrated
Flight control firmware version: HAKRC F722D
BEC: 5V/3A
BEC:10V/2.5A
Sensor: Built-in current sensor
Firmware Target: HAKRCF722D
LED: Support WS2812 and other programmable
Compatible receivers: CRSF / Frsky/ Futaba/ Flysky/TBS Crossfire/ DSMX: DSM2 receiver
Dimensions: 40x30mm (20mmx20mm mounting hole)
ESC
Input voltage: 2S-6S
Continuous current: 40A
Peak current: 50A
Firmware: BLHeli_32
Firmware Target: HAKRC_AT4G_Multi_32_9.Hex
MOS Model: 7140
PWM：24-128K
Protocol support: PWM, Oneshot125, Oneshot42,
Multishot, Dshot150, Dshot300, Dshot600
Continuous current: 40A
Peak current: 45A
Includes
1x HAKRC F7220 2-6S AIO Whoop/Toothpick Flight Controller w/ 40A 5V/3A & 10V/2.5A BEC
1x XT60 H-M
1x Capacitor
4x Purple Gummies
2x Power lead
1x Plug harness
Wiring Diagram
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that’s too simple. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for whoop because of the ultra light and Nano size.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Packet Rate: 25/50/150/250/500Hz
RF Frequency: 2.4GHz
Antenna: Ipex 4
Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX
Includes
1x HappyModel EP1 RX Express LRS Receiver
1x Short antenna
1x Long antenna
The PP RX is designed by @Jye Smith from ExpressLRS development team. Its main hardware architecture is STM32L432KBU6 MCU and SX1280 RF chip. It has a built-in ceramic antenna, which is super light and small in size. On the basis of PP RX, we have developed the Nano 2.4GHz rx of ESP8285 version named EP1 and EP2. The RF module of EP1/EP2 is the same like PP RX and use ESP8285 MCU . So you can upgrade firmware by WIFI , that’s too simple. Due to the low-latency and high-refresh-rate RF module, they are very comfortable for FPV race and Long Range FPV. And very suitable for whoop because of the ultra light and Nano size.
Check out our other great receivers, and the rest of our Happymodel offerings.
Specifications
Packet Rate: 25/50/150/250/500Hz
RF Frequency: 2.4GHz
Antenna: SMD Ceramic antenna
Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX
Includes
1x HappyModel 2.4GHz EP2 RX Express LRS Receiver - For Sale At RaceDayQuads
Get ready to experience the thrill of FPV racing with the HappyModel Bassline FPV Drone Frame Kit! This high-quality frame kit is designed for maximum performance and durability. It's made of lightweight and durable carbon fiber and comes with all the necessary hardware for easy assembly. Upgrade your FPV racing game with the HappyModel Bassline FPV Drone Frame Kit from RaceDayQuads - order yours today!
Be sure to check out all our Micro Frames, and all our Happymodel products!
Specifications
Wheelbase: 90mm
Mount hole size: 25.5x25.5mm
Size: 115x115x40mm
3K carbon
Motor Mounting: 9x9mm/12x12mm M2
Includes
1x 3K carbon fiber bottom plate
1x 3D Printed battery tray
8x Rubber damping balls
4x M2x16 screw for Bassline mount
4x M2x22 screw for Bassline HD mount
8x M2 Nut
1x Battery Anti-skid Mat
The HappyModel BNF 1S Mobula 7 HD Whoop version is a light and efficient 75mm brushless whoop which provides 1080P HD video recording functionality. HappyModel added blackbox for this 1s 75mm HD recording whoop so that you now have gyroflow functionality. Unlock the ultimate smooth flights with a combination of the Mob 7 HD and gyroflow!
Check out the rest of pre-built quads and our HappyModel selection!
Specifications
HappyModel X12 AIO
Input Voltage: 1-2S
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: MPU6000 or ICM20689 or BMI270
Max Continuous Current: 12A
VTX Output Power: 25-400mW
Antenna Connector: U.FL
OSD: Yes
Betaflight Target: ELRS Version: CRAZYBEEF4SX1280, PNP Version: CRAZYBEEF4DX
ESC Firmware: Z_H_30_REV16_7
Mounting Pattern: 25x25mm
Weight: 5.1g
HappyModel RS Motor
Input Voltage: 1S
KV: 20000KV
Shaft Diameter: 1.0mm
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Motor Dimension: Φ10.5x13.5mm
Wire length(include connector): 30mm
Weight: 2g
Runcam Split 3 Lite
Video Resolution: 1080@60fps/1080@50fps/1080@30fps/720@60fps
Field of View(FOV): Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video File Format: MOV
Image Resolution: 2MP
Signal System: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Includes
1x HappyModel BNF 1S Mobula 7 HD Whoop
The Crux 35 is an ultra-lightweight 3.5Inch FPV freestyle and racing drone, the weight of the whole drone is only 87g for the analog version and 108g for the digital HD version. The Crux35 series drone use Happymodel's EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle flying experience.
Happymodel Crux35 Racing Drone V2 comes with the CrazyF411 ELRS flight controller. This board comes with an integrated UART 2.4GHz ExpressLRS receiver and 20A BLheli_S ESC(Bluejay firmware pre-installed) which could support 3-4S.
The new V2 version comes with CrazyF411 ELRS AIO flight controller built-in UART ExpressLRS receiver which allows for updating the receiver with ease.
Choose from between ELRS 2.4GHz and FrSky for your receiver.
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Features
Bind tutorial for ELRS
Ultra-lightweight 3.5-inch BNF FPV Freestyle Drone
HD video transmission and analog video transmission are optional
Integrated ExpressLRS UART receiver
High efficiency EX1404 power system
Can be equipped with Naked Gopro or SMO4K
Specifications
Weight: 87g
Brand: Happymodel
Wheelbase: 150mm
Dimensions: 130mmx130mmx45mm
Receiver option: UART ExpressLRS 2.4GHz
HappyModel Flight Controller (ELRS Version)
Input Voltage: 2-4S LiPo
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: BMI270 or ICM42688P (SPI control)
ESC Connections: Yes
Firmware: CrazybeeF4DX
Current Sensor: Yes
Mount pattern: 25.5x25.5mm (M2)
Dimensions: 32x28x9mm
Weight: 5g
Built-in 20A Blheli_s ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1A BEC
Onboard ESC:
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite and ESC-Configurator programmable
Factory firmware: Bluejay 0.18.1
Firmware target: F_H_40_48_v0.18.1
Support DSHOT150/DSHOT300/DSHOT600
Default protocol: DSHOT300
HappyModel EX1404 3500KV Motor
Mode: EX1404
Kv: 3500Kv
Input Voltage: 3-4S LiPo
Configuration: 9N12P
Motor Dimensions: Φ17.8mm x 17.6mm
Stator Dimensions: Φ14mm x 4mm
Shaft Diameter: 1.5mm
Mounting Pattern: Φ9mm
Weight: 9g
HappyModel Propellers
Propeller Diameter: 3.5 inch
Pitch : 2
Blades : 3
Material : Poly Carbonate
Weight : 1.5g
Hub Diameter : 10mm
Hub Thickness: 4.7mm
Shaft :1.9/1.5/1.9mm
Adaptor Rings : NO
Caddx Ant Camera
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC and PAL(switchable)
MENU: Support
IMAGE: 4:3 or 16:9
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio: >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm/F2.5
Minimum illumination: 0.001Lux
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14x14mm
Wide Power Input: DC 3.7-18V
Work Temperature: -20°C~+60C
Work Humidity: 20%~80%
Weight: 1.7g
Happymodel OVX303 5.8G analog VTX or OVX306 5.8G analog VTX
Input Voltage: 5V
RF Output Power: 25-300mW
Antenna Connector: U.Fl
Power/Video Connection: Solder Pads
OVX303 Stack Size: 16x16mm, 20x20mm, 25x25mm
OVX306 Stack Size: 25x25mm
Weight: 0.9~1g
Includes
1x HappyModel BNF Crux35 V2 3.5" Analog Quad - Choose version
1x 5D-OSD menu board
1x Screw Driver and Screw Set
8x HQProp T3.5X2X3Grey (4cw+4ccw)
1x Buckle Velcro for battery
Introducing the Moblite7 Ultralight FPV Brushless Whoop! Made in collaboration with FPV pilot "Mr. Shutterbug," this whoop is one of the lightest 75mm drones on the market! And glows in the dark!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Specifications
Weight: 36g With battery
Propellor Size: 75mm
Antenna: Linear Dipole
HappyModel DiamondF4 FR FC
Input Voltage: 1S LiPo
MCU: STM32F411CEU6
Gyro: MPU-6000
OSD: Yes
UARTs: 2 Sets
ESC Connections: Yes
FC Firmware: CrazybeeF4F
BEC: 5V 1A
Current Sensor: Yes
Buzzer: Yes
Barometer: No
Black Box: No
Max. Continuous Current: 5A
Max Burst Current: 6A (3sec)
ESC Firmware: BLheli_S
Factory firmware: O_H_50_REV16_8.HEX
Stack Size: 25x25mm
Dimensions: 29x29mm
Motors
Stator Size: 0802
Kv: 19000
Weight: 1.7g
Runcam Nano 3 Camera
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens: 2.1mm(M8) FOV 160°
Signal System: NTSC
S/N Ratio: > 50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: 0.01Lux@1.2F
D-WDR: Auto
Day/Night: Color
Power: DC 3-5.5V
Current: 110mA@5V
Housing Material: ABS
Net Weight: 1.1g
Includes
1x 75mm Frame (Mobula7 frame)
1x Option1: DiamondF4 FR built-in SPI Frsky receiver
4x EX0802 KV19000 Unibell brushless motor
1x HQPROP 40MMX2 propeller(4cw+4ccw)
1x Runcam Nano3
1x Built-in 5.8G 40ch 25mw-200mw VTX
2x 1s 650mah Lipo battery
1x Propeller disassemble tool
1x Screwdriver
1x Happymodel Carry case
All product containing lithium batteries must be shipped by a ground shipping method. Please be aware Betaflight 4.3.1 firmware has a bug, Please do not flash version 4.3.1.
This is the V2 version of the Mobula 6 HD. This version features an ICM20689 Gyro as well as an OpenVTX 400mW VTX.
The Highly sought after Mobula6 now comes in HD! Record all your sessions in HD with the onboard RunCam split 3 Lite.We recommend RDQ 1S 300mAh LiPos for this whoop! Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
Extreme light 1S 65mm Brushless HD whoop only 27g
Come with Runcam Split3-lite 1080P HD DVR
Smooth and agile
Compatible for 1S Lipo/LIHV
Camera Angle adjustable
Specifications
Wheelbase: 65mm
Size: 80x80x40mm
Weight: 27g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Internal SPI DSM2/DSMX version(Compatible with SPEKTRUM DSM2/DSMX protocol radio transmitter)
External TBS CRSF NANO version(Compatible with TBS Transmitters)
Motors
Model: EX0802 19000KV
Configuration: 9N12P
Stator Diameter: 8mm
Stator Length: 2mm
Shaft Diameter: Φ1mm
Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm
Weight(g): 1.7g
No.of Cells(Lipo): 1S only
Flight Controller
(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
(DSM2/X SPI RX version) CRAZYBEEX DXS DSM2/X version firmware target: CrazybeeF4DXS
(External TBS CRSF NANO RX version) CRAZYBEE F4 Lite Firmware target: CrazybeeF4DX
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G 400mW VTX
Built-in SPI Frsky/Flysky/DSMX receiver
Built-in 5V 1A BEC
Built-in voltage detection
ESC
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600
VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band Smart audio ready
Runcam Split3 Lite
Model: RunCam Split3-Lite
Field of View(FOV):Recording FOV 165°(FPV FOV: 165 ° @16:9, 130 ° @4:3)
Video Resolution:1080@60fps/1080@50fps/1080@30fps/720@60fps
Video File Format: MOV
Image Resolution:2 MP
TV Mode: NTSC (720*480)/PAL (720*576) Switchable
Interface: JST 1.25mm / UART and SH 1.0mm
Max Micro SD Card Supported 64G(need Class 6 or above, recommend Class 10/UHS-I/UHS-II/UHS-III)
Hole Distance of Installation: 25.5*25.5mm
PCB Size: 29*29mm
Lens Module Size: 14*14mm
Lens Specs: M9
Power Input: DC 5-20V(Non-direct power supply from battery. Powered directly with battery will generate surges and burn the camera.)
Working Current: 450mA @5V
Includes
1x Happy Model BNF Mobula 6 HD 1S Whoop Quad - Choose Your RX
HappyModel has been an amazing company, bringing us FPV enthusiast quality whoops to fly. Take a look at HappyModels first ever whoop on a 85mm frame. It comes with X12 series flight controller, EX1103 KV11000 motors and Gemfan Hurricane 2023 tri-blade propellers, all together gives this whoop an amazing performance for an extremely smooth flight.
Choose between PNP (No RX) and BNF (ELRS SPI 2.4)
Be sure to check out all our pre-built quads, and all our Happymodel products!
Features
X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and OPENVTX
VTX Power up to 400mw
ELRS V2.0 (Default), can be flashed to ELRS V3.0
EX1103 KV110000 motors
CaddxFPV Ant FPV camera
Smooth and powerful
Compatible for 1S-2S Lipo/LIHV battery
3D Printed Camera Lens Protector
User Manuals
ELRS (SPI)
PNP (No RX)
Specifications
Brand Name: Happymodel
Motor: EX1103 KV11000
AIO: X12 5-IN-1 AIO flight controller
Camera: CaddxFPV Ant FPV camera
Prop: Genfan 2023-3 propellers
Weight: 42.7g
Input Voltage: 1-2S
Wheelbase: 85mm
Size: 120mmx120mmx50mm
Motor Specifications
Model: EX1103 KV11000
Configuration: 9N12P
Stator Diamter: 11mm
Stator Length: 3mm
Shaft Diameter: Φ1.5mm
Motor Dimension(Dia.xLen): Φ13.5mmx15.5mm
Weight(g): 3.8g
No.of Cells(Lipo): 1-2S
Propeller Specifications
Weight: 0.88g
Material: PC
Pitch: 2.3inch
Props Dia: 52.17mm
Center Thickness: 5mm
Center Hole Dia: 1.5mm
Flight Controller Specifications
MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: ICM20689 or ICM42688P(SPI connection)
Mount hole size: 25.5mm x 25.5mm
Power supply: 1-2S battery input (DC 2.9V-8.7V)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G OpenVTX 0mw~400mw
Built-in ExpressLRS 2.4G,Frsky D8/D16,Flysky AFHDS 2A
Built-in voltage detection
Built-in current sensor
Onboard 4in1 ESC
Power supply: 1-2S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support BLHeliSuite programmable
Firmware target: Z_H_30
Default protocol: DSHOT300
Support Bluejay firmware
Onboard SPI ELRS 2.4GHz Specifications
Packet Rate option: 50Hz/150Hz/250Hz/500Hz
ExpressLRS Firmware version: V2.0
RF Frequency: 2.4GHz
Antenna : SMD antenna
Telemetry output Power: <12dBm
Receiver protocol: SPI ExpressLRS
Could flash FC firmware to support ExpressLRS v3.0 TX module
PNP Version Specifications
Full UART1 for external Receiver
Support CRSF/GHOST/SBUS/IBUS/DSMX protocol
IR1 pad(invert RX1) used for SBUS input
Includes
1x HappyModel BNF Mobula8 1-2S Brushless Analog Whoop - Choose Your Receiver
1x Gemfan Hurricane 2023 tri-blade propellers (4CW+4CCW)
1x Screw Driver
1x Extra camera canopy
Experience powerful performance with the HappyModel BNF Mobula8 1-2S HD 85mm! This amazing quadcopter comes with an amazing DJI O3 Air Unit and Micro Cam, as well as Crazy F405 ELRS HD flight controller, EX1103 11000Kv motors, and Gemfan Hurricane 2023 tri-blade propellers for superior power performance. Get the perfect HD experience with the Mobula8!
Be sure to check out all our pre-built quads, and all our Happymodel products!
Specifications
Camera/VTX: DJI O3 Air Unit
Item Name: Mobula8 1-2S 85mm Micro FPV whoop drone
Size: 120mmx120mmx50mm
Brand Name: Happymodel
Wheelbase: 85mm
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Mount hole size: 25.5mm x 25.5mm
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
MOTORS
Motor Dimension(Dia.xLen):Φ13.5mmx15.5mm
Mode: EX1103 11000Kv
Shaft Diameter:Φ1.5mm
No.of Cells(Lipo):1-2S
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:3mm
Weight(g):3.8g
PROPELLERS
Center Hole Dia:1.5mm
Center Thickness:5mm
Props Dia:52.17mm
Weight:0.88g
Pitch:2.3inch
Material: PC
Includes
1x HappyModel BNF Mobula8 1-2S HD 85mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz
Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card.
Experience powerful performance with the HappyModel BNF Mobula8 1-2S HD 85mm! This amazing quadcopter comes with Crazy F405 ELRS HD flight controller, EX1103 11000Kv motors, and Gemfan Hurricane 2023 tri-blade propellers for superior power performance.
Be sure to check out all our pre-built quads, and all our Happymodel products!
Specifications
Item Name: Mobula8 1-2S 85mm Micro FPV whoop drone
Size: 120mmx120mmx50mm
Brand Name: Happymodel
Wheelbase: 85mm
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Mount hole size: 25.5mm x 25.5mm
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
MOTORS
Motor Dimension(Dia.xLen):Φ13.5mmx15.5mm
Mode: EX1103 11000Kv
Shaft Diameter:Φ1.5mm
No.of Cells(Lipo):1-2S
Configu-ration:9N12P
Stator Diamter:11mm
Stator Length:3mm
Weight(g):3.8g
PROPELLERS
Center Hole Dia:1.5mm
Center Thickness:5mm
Props Dia:52.17mm
Weight:0.88g
Pitch:2.3inch
Material: PC
Includes
1x HappyModel BNF Mobula8 1-2S HD 85mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz
An F405 chip FC with built-in Serial ELRS receiver, 4in1 12A ESC, and 8Mbp black box. Optimized layout, supports 1-2S Lipo/LiHV. Perfect for Tinywhoop/Cinewhoop/Toothpick. Betaflight/INAV compatible. 3 sets UARTs, 5V/3A & 9V BECs, barometer. Get performance to elevate your FPV. Experience exceptional agility and power for your racing and freestyle sessions. With this board, you'll have the perfect setup to take your flight to the next level.
Browse the rest of our Whoop AIO Boards and our Happymodel gear.
Specifications:
Brand Name: Happymodel
Item Name: CrazyF405HD ELRS 1-2S AIO Flight controller
Mount size: 25.5mmx25.5mm
Weight: 4.8g without power lead wire
Firmware target: BetaflightF4
Support 1-2S Lipo/LiHV battery
FLIGHT CONTROLLER
Built-in voltage meter sensor, voltage meter scale 110
Built-in current meter sensor, current meter scale 470
MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
Power supply: 1-2S battery input (DC 2.9V-8.7V)
GYRO Sensor: BMI270 (SPI connection)
Built-in 12A(each) Blheli_S 4in1 ESC
Built-in Serial ExpressLRS 2.4G
Model: Crazy F405 ELRS HD
Built-in BMP280 Barometer
Built-in 8MBp black box
ONBOARD UART ELRS 2.4GHZ RECEIVER
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
Could update firmware via ExpressLRS configurator
Antenna: enameled copper wire 31mm length
Default firmware version: ExpressLRS V3.0.1
Firmware target: HappyModel EP 2400 RX
Telemetry output Power: <12dBm
RF Frequency: 2.4GHz
ONBOARD 4-IN-1 ESC
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Bluejay ESC V0.19
Support BLHeli_S Bluejay firmware
Power supply: 1-2S LiPo/LiPo HV
Default protocol: DSHOT300
Firmware target: Z-H-30
*When using 1s battery and high KV 0702/0802 motors, should set the startup power to 1100/1200
Includes
1x HappyModel Crazyf405 ELRS HD 1-2S AIO Whoop/Toothpick Flight Controller w/ 12A 8Bit 4in1 ESC & ELRS 2.4GHz RX
1x Power lead with a XT30 Connector
Wiring Diagram
Equip your 2-4S drone with the HappyModel CrazyF411 F4 Flight Controller. Enjoy flying with its 20A 8Bit 4in1 ESC and ELRS 2.4GHz receiver featuring a high-sensitivity SX1280 frequency chip for low latency, high packet rate, and great range. With a big Mosfet that supports up to 20A currents, this controller is perfect for FPV drones and strong enough for race or freestyle flying. This flight controller lets you update firmware through Betaflight pass-through or WIFI. The 2.4GHz ExpressLRS receiver is equipped with the SX1280 radio frequency chip with high sensitivity, high packet rate, and low latency. The default firmware is ELRS V3.0.1. Get ready to take your drone game to the next level!
Browse the rest of our Whoop AIO Boards and our Happymodel gear.
Features
Integrated serial 2.4GHz ExpressLRS receiver
Pre-installed with Bluejay firmware)
Coming with a BMI270 gyro
Specifications
Flight Controller
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Gyro: ICM42688P
Mount pattern: 25.5x25.5 M2
Size: 32x28x9mm
Power supply: 2-4S Lipo battery
Built-in 20A Blheli_S ESC each
Built-in Betaflight OSD(SPI Control)
Built-in UART ExpressLRS 2.4GHz receiver
Built-in 5V 1.5A BEC
Flight controller firmware target: CRAZYBEEF4DX
Weight: 4.97
Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Currents: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: Bluejay 0.18.1Firmware target: F_H_40_48_v0.18.1
Default protocol: DSHOT150/DSHOT300/DSHOT600
Onboard UART ExpressLRS 2.4GHz Receiver
Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHzAntenna plug: IPEX
Telemetry output Power: <12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1
Onboard voltage and Amperage Meter Settings
Voltage meter scale setting 110
Amperage meter scale setting 470
Includes
1x HappyModel CrazyF411 F4 2-4S Whoop/Toothpick AIO Flight Controller w/ 20A 8Bit 4in1 ESC - ELRS 2.4GHz (UART)
2x Wire
1x Hardware Set
4x Grommets
Wiring Diagram & Binding Procedure
Binding procedure
Supply power to the flight controller by plug USB, wait until the green LED on the FC is off, immediately turn off the power, and then repeat again the above steps. When the FC is powered on for the third time, the green LED light will start to double-flash, which means that the RX enters the binding mode
Please make sure your ExpressLRS tx module firmware is v3.x.x. And go to ExpressLRS.lua from “TOOLS” menu of your radio transmitter. Then hit [Bind] to binding with the onboard ExpressLRS receiver. The green LED should blinking slowly first then turn to solid, that means binding was successfully. If the green led still keep double flash after binding ,please change Model Match tab value from “off” to “on” or from “on” to “off”
Receiver LED status meanings
Green LED solid means bind successful or RC link established; Green LED double-flash means get into bind mode; Green LED flash slowly means no RC signal input from TX module; Green LED continuous flash fast means ExpressLRS wifi enabled.
Bind successful
Bind Mode
No RC Input
Wifi Mode
This Slim Pro TX module is designed by Happymodel and based on the open-source ExpressLRS which is a very popular low latency and high packet rate RF module for RC Airplane and FPV Racing drones. Its main hardware architecture is ESP32, ESP8285, and SX1280 RF chip. The ES24TX Slim Pro module is a complete solution which is already pre-load the Expresslrs firmware and its plug-and-play for Frsky X-lite/X-lite pro/X9 Lite, TBS Tango2.This Slim Pro module comes with an aluminum alloy shell and is equipped with a cooling fan that automatically works when the module is working at 250mw.The slim pro-TX module supports a maximum power output of about 1000mw, this would be very useful for Long Range FPV.
Check out our other ELRS accessorieses, as well as the rest of our HappyModel selection.
Features
Supports up to 1000mw RF power (T-lite radio and Tango2 radio need external power supply)
RGB LED ready
Cooling Fan ready
Open source ExpressLRS
Long-range, low latency, and High re-flashed Rates
Telemetry data transmission supported
CNC aluminum protective shell
Specifications
Regulatory Domain: ISM2400
MCU: ESP32(main),ESP8285(as ESP backpack)
RF chip: SX1280IMLTRT
Frsky Lite 8pin socket
Frequency Range: 2400 MHz to 2500 MHz
Maximum receive refresh rate: 500Hz
Minimum receiver refresh rate: 25Hz
RF Output Power: ≤30dBm
Power supply voltage: 5v~12v
Weight: 50gram (without antenna）
Dimension: 67.5x30x20.5mm (without antenna)
Antenna gain: 1.87dBi
Antenna Connector: SMA
Includes
1x HappyModel ES24TX Slim Pro 2.4GHz RC Transmitter Module
1x Antenna
Due to this item’s size or weight, it is not available for free shipping and may be shipped via ground.
This is a PNP wing, but assembly is still required.
Designed for FPV flying, the Heewing T1 Ranger PNP Twin Motor Wing is a great wing all around. Lightweight and portable, with a quick disassembly design, this build only takes minutes to put together and take apart. A small wingspan with large space for stress-free placement for your electronic equipment. And many other features to check out!
Check out all our PNP wings, Kit wings, and all out HeeWing products!
Features
Two-section hatch with ample room hatch for electronics
High-Quality EPP / Carbon FIber / Aluminum Materials
Supports External FPV Camera Mounting
730mm Fixed Wing Span
Quick Release Structure
Dual Motors
Specifications
Wingspan: 730mm
Length: 645mm
Hight: 140mm
Dimension: 660x225x135mm
Propeller recommend: 5-6 inch
Battery recommend : 4S 1300-2200mah
Battery: 2S~3S 1300mah~5000mah LiPo
Radio System: 2.4G 6CH
Material: EPP / ABS+PC / Carbon fiber / Aluminum
Includes
1x Heewing T1 Ranger PNP Twin-Motor Wing
Due to this item’s size or weight, it is not available for free shipping and may be shipped via ground.
This is a PNP wing, but assembly is still required.
Designed for FPV flying, the Heewing T1 Ranger PNP VTOL Twin Motor Wing is a great wing all around. Lightweight and portable, with a quick disassembly design, this build only takes minutes to put together and take apart. A small wingspan with large space for stress-free placement for your electronic equipment. And many other features to check out!
Important Note
T1 VTOL-PNP w/FC, Factory pre-installed. Save your time and enjoy to fly! Though regarding to the FC, it is pre-installed on the plane, but it is not fully tuned. It has flight control VTOL parameters for free, but this parameter is for reference only, and we do not take any responsibility or obligation for this parameter. It is strongly recommended that players must strictly adjust according to their actual flight environment and needs！
Check out all our PNP wings, Kit wings, and all our Hee Wing products!
Features
Two-section hatch with ample room hatch for electronics
High-Quality EPP / Carbon FIber / Aluminum Materials
Supports External FPV Camera Mounting
730mm Fixed Wing Span
Quick Release Structure
Dual Motors
FC Manual
Specifications
Wingspan: 730mm
Length: 645mm
Hight: 140mm
Dimension: 660x225x135mm
Propeller recommend: 5-6 inch
Battery recommend : 4S 1300-3500mAh
Radio System: 2.4G 6CH
Material: EPP / ABS+PC / Carbon fiber / Aluminum
Includes
1x Heewing PNP T1 Ranger VTOL Twin-Motor Wing - Grey - Choose Version
1x Fixed Wing Hardware Kit
