Lightweight 65mm whoop drones are becoming popular among racing enthusiasts. Experience powerful performance with the BetaFPV 0702 30000Kv Dual Ball Bearing Micro Motor 4 Pack. These motors boast dual ball bearings and strong reliability and efficiency to empower your flight.
Take a look at all of our micro motor selections and our BetaFPV products!
Features
These motors are customization designs for the ultra-lightweight 65mm racing drone, featuring unparalleled performance in extreme racing flight.
The 0702 motor boasts double ball bearings
For those seeking even higher speeds, the 30000Kv option provides more punch on the throttle. These motors are ideal for indoor FPV racing and enable aggressive flying.
Paired with The PEEK screws, only weighing 0.10 grams/12pcs, it can save up to 0.46 grams for a build. With more heat resistance, anti-friction, anti-shock, and anti-fatigue properties, the PEEK screws are both reliable and durable.
Plug-and-play motors
Specifications
Bearing Dual Ball Bearings
KV: 30000
Weight: 1.52g±0.03g
Weight Without Connector: 1.45g
Color: Black/Red
Shaft Diameter: 1mm
Shaft Length: 4.2mm
Hole Distance: 6.6mm
Motor Mount Holes: M1.4
Input Voltage: 1S
Cables 35mm including connector, 30AWG cables
Dimensions: 12.75xφ9mm
Motor Bolt Pattern: 6.6mm Tri-Mount
Includes
1x BetaFPV 0702 30000Kv Dual Ball Bearing Micro Motor 4 Pack
15x M1.4x3 PEEK screws
12x M1.4x3 metal screws
Lightweight 65mm whoop drones are becoming popular among racing enthusiasts. Experience powerful performance with the BetaFPV 0702SE 25000Kv Brass Bushings Micro Motor 4 Pack. Enjoy a higher level of performance with this reliable 4-pack.
Take a look at all of our Micro Motor selections and our BetaFPV products!
Features
These motors are customization designs for the ultra-lightweight 65mm racing drone, featuring unparalleled performance in extreme racing flight.
Paired with The PEEK screws only weighing 0.10 grams/12pcs, it can save up to 0.46 grams for a build. With more heat resistance, anti-friction, anti-shock, and anti-fatigue properties, the PEEK screws are both reliable and durable.
The truth is that for all speeds of 0702 motors, there is a 603 or 802 size motor that can achieve the same thrust with greater efficiency, the 0702 is favored by active FPV pilots for its ability to reduce weight away from the aircraft's center of gravity. The brass-bushed 0702SE motor is a reliable and cost-effective choice for these pilots.
Plug-and-play motors
Specifications
Bearing Brass Bushings
KV: 25000
Weight: 1.42g±0.03g
Weight Without Connector: 1.35g
Color: Ice Blue/Black
Shaft Diameter: 1mm
Shaft Length: 4.2mm
Hole Distance: 6.6mm
Motor Mount Holes: M1.4
Input Voltage: 1S
Cables 35mm including connector, 30AWG cables
Dimensions: 12.75xφ9mm
Includes
1x BetaFPV 0702SE 0702 25000Kv Brass Bushings Micro Motor 4 Pack
15x M1.4x3 PEEK screws
12x M1.4x3 metal screws
0802SE Brushless Motors is a lightweight of only 1.8g/pc for 1S whoop drones. It ensures excellent performance of power and thrust and makes the perfect dynamic balance, providing flexibility and longer flying time for drones.
Take a look at all of our micro motor selections and our BetaFPV products!
Features
0802SE 19500KV Brushless Motors (2022 version) comes with a completely new look. The whole motors are silver in the air, looking very bright.
0802SE Motor makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time. With its lightweight of 1.8g/pc, it is ideal for the weight-sensitive 65mm brushless whoop drone.
19500KV and 23000KV options greatly meet the pilots' needs for different flying purposes.
Lead wire is soldered to the PCB, allowing you to repair it easier once disconnected.
Specification
Item: 0802SE 19500KV brushless motor
Weight: 1.83g/pc
Kv: 19500KV
Color: Black/Ice Blue
Shaft length: 5mm
Shaft diameter: 1mm
Hole distance: 6.6mm
Motor Mount Holes: M1.4
Input Voltage: 1S
Cables: 35mm long, 30AWG cables
Dimensions: 10.5x10.5x13.8mm (2022 version)
Bearings: Brass Bushings
Includes
4x BETAFPV 0802SE Brushless Motors 19500Kv
1x Pack of M1.4x3 Screws
BetaFPV has stepped it up a notch with their new 1 Watt Express LRS transmitter! Compared with 500mW versions, it not only has a built-in cooling fan but also the heat sink is included, which enhances the performance of cooling. So this module can work properly in daily use with no need to worry about temperature.
Check out our ELRS gear, RC Transmitters and all our BetaFPV products!
Specifications
Packet refresh rate: 50Hz, 150Hz, 250Hz, 500Hz
RF output power: 25mW, 50mW, 250mW, 500mW, 1W
Frequency bands: 2.4GHz ISM
Heatsink: Included
USB Port: Type C
Backpack Function: Supported
Note: Please assemble the antenna before power on. Otherwise, the PA chip in the Micro TX module will be damaged permanently.
Note: Please DO NOT use 3S or above battery to power up the TX module via XT30 port. Otherwise, the power supply chip in the TX module will be damaged permanently.
Note: Please do not turn on all DIP switches at the same time.
BETAFPV Micro TX Module ELRS V2.0.0 firmware is published. The firmware does not include the Binding Phrase. So please make sure the receiver works on officially major release V2.0.0 protocol and no Binding Phrase set.
Support 5D buttons and the OLED menu with the official ELRS 2.0.0 release.
The color of the LED changes automatically according to the system status.
Other new and various features are fully synchronized with the official ELRS 2.0.0.
When entering OLED menus page with long pressing, the connection between RF TX module and receiver works normally. Please do not change the Pkt Rate, otherwise, you must re-power the receiver.
You could all use the ELRS offical firmware V2.0-RC2 now, but lost the function of OLED and Joystick. We will work with the ELRS dev team and make the ELRS official firmware support the full function of the Micro TX Module. For the milestone, OLED will be supported in the V2.1 officially.
https://github.com/BETAFPV/ExpressLRS
User manual of How to Flash Firmware of ELRS RX/TX.
Includes
1x BETAFPV ELRS Micro TX module
1x BETAFPV Moxon antenna
1x Micro TX module user manual
1x Spare USB data cable (Type-A to Type-C)
Lightest 1103 motors in the world. Only 3.2g with connector. This motor was made custom for the Beta75X 2S Whoop.
A 1.5mm header pins connector is include. So no soldering needed, just plug and play.
Check out our ever-growing selection of Whoop products!
Features
1103 11000KV brushless motors is customed for 2S brushless whoop drone.
Fit with 1735, 1935, 2030, 3020 propellers
Shaft Diameter: 1.5mm, Weight: 3.2g
Compatible with 2S lipo battery
Specifications
Height: 14mm
Weight: about 3.2g
Shaft: φ1.5mm
Motor Mount Holes: M1.6 on Dia 8.5mm
KV (rpm/V): 11000
Voltage: 7.4V, 2S Lipo battery
Plug: Micro JST-1.25 3-pins connector
Includes
4x BetaFPV 1103 11000Kv Micro/Whoop Motor
BETAFPV Micro receiver is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
ExpressLRS now supports direct PWM output from receivers that have been specifically designed for this mode. BETAFPV ELRS Micro receiver features PWM output for the application of fixed-wing, helicopters, RC cars, boats and etc, and supports failsafe function, which can protect RC models from being out of control. Besides, the plug-and-play design makes it very easy and friendly to use.
Check out the rest of our ELRS gear, as well as all of our BetaFPV selection!
Specifications
PWM Channels: 5
Serial Output Protocol: PWM or CRSF
Dimensions: 19x32x9mm (without antenna)
MCU: ESP8285/SX1280/SX1281
Telemetry Power: 12.5dbm/17mW
Frequency Band: 2.4GHz ISM
Input voltage: 5V~9V
Firmware: ExpressLRS v2.0
Antenna: IPEX MHF + T antenna (recommend 80mm Dipole T Antenna)
Weight: 4.5g (with antenna)
Includes
1x BetaFPV 2.4GHz Micro ELRS PWM Receiver
1x Antenna
Classic 1102 stator size, matched with an impressive 22000Kv, gets you amazing whoop motors that will take you from regular flying to absolute ripping. Choose between a black base with red accents or a silver base with blue accents. We also carry the classic 1102 18,000Kv version as well!
These motors come with motor plugs attached.
Take a look at all of our micro motor selections and our BetaFPV products!
Features
Adopts the technology of ball bearing, which effectively reduces the friction between the bearing surfaces, increases the duration of the motor, and improves its efficiency.
Lead wire is soldered to the PCB, which allows you to repair it more easily once disconnected.
With exquisite workmanship, provides the most incredible power and thrust in the lightest weight of 2.79g; sturdy structure, and high-quality materials make it performs like a beast.
Possesses dynamic balance and crush-resistant damping bearing, which can eliminate vibration effectively.
The 22000KV version can provide more thrust for aggressive indoor FPV racing.
Specification
Height: 13.6mm (2022 version)
Weight: 2.79g/pc
Shaft Diameter: 1.5mm
Shaft Length: 5mm
Motor Mount Holes: 3-M1.4-φ6.6
KV (rpm/V): 22000KV
Input Voltage: 1S Lipo
Plug and cables: Micro JST-1.25 3-pin connector with 28AWG cables
Includes
1x BetaFPV 2022 Series 1102 22000Kv Micro/Whoop Motor 4 Pack - Choose Your Color
BETAFPV offers 2 versions of the 2S Battery Charger and Voltage Tester, each with different ports - BT3.0 and XH2.54 - capable of charging both LiHV 8.7V and LiPo 8.4V batteries. Not only does it have a digital display function, but it also features 2S battery voltage monitoring capabilities. Additionally, it supports PD3.0 fast charging protocol. This compact and portable charger is fully functional and user-friendly, and caters to the charging needs of 2S quadcopter enthusiasts, empowering them to recharge their batteries anytime, anywhere.
Check out our other charging accessories, as well as our range of BetaFPV gear!
Features
A compact and portable 2S Battery Charger and Voltage Tester with a digital display, specifically designed for the BT3.0 series of batteries.
It supports the PD3.0 fast charging protocol, offering higher power output and multiple charging options for a faster and safer charging experience with compatible devices.
Equipped with a digital display function and capable of monitoring battery voltage during charging.
With dual variants boasting BT3.0 and XH2.54 ports, this charger offers RC users different connection options.
Featuring a Type C interface instead of a USB interface, providing an even wider selection of charging options
Fulfilling the charging requirements of 2S batteries, this charger is a go-to choice for discerning enthusiasts.
XH2.54
This charger is compatible with 2S LiPo batteries(8.4V) and has an XH2.54 battery port. Please note that charging 2S LiHV batteries (8.7V) may result in undercharging. We recommend using a LiPo 2S battery with a corresponding balance connector available in the market. During the charging process, if the digital display shows a voltage exceeding 8.4V (e.g. 9V), please disconnect the power supply immediately and check if there is any issue with the battery or the charger.
BT3.0
This charger is designed to charge 2S LiHV batteries(8.7V) with a BT3.0 battery port. Please note that attempting to charge 2S LiPo batteries(8.4V) may pose a risk of overcharging. To ensure safe and optimal charging, we recommend using it with the BETAFPV BT3.0 450mAh 2S LiHV battery. During the charging process, if the digital display shows a voltage exceeding 8.7V (e.g. 9V), please disconnect the power supply immediately and check if there is any issue with the battery or the charger.
Specifications
Battery Type: BT3.0-LiHV(charging voltage:8.7V) / XH2.54-LiPo(charging voltage:8.4V)
Product Color: White(BT3.0) / Black(XH2.54)
Input Interface: Type-C USB
Input Voltage Range: 5-12V
Input Power: Maximum 15W
Maximum Input Current: 2.5A
Charging Protocol: PD3.0
Weight (per charger): 17.0±1.0g
Dimensions (L×W ×H): 61*25*17mm
Battery Capacity Display: LED Digital Display displays the total voltage and individual cell voltage of the
2S battery
LED Digital Display and Red LED indicate charging status:
Usage Notes
Please note the polarity markings on the device and do not connect the charger in reverse polarity.
The 2S Battery Charger and Voltage Tester only supports charging for 2S batteries, not 1S batteries.
The charger can only charge one battery at a time and is not designed for charging two or more batteries simultaneously.
Includes
1x BetaFPV 2S Battery Charger / Voltage Tester - Choose Your Version
All batteries must be shipped by a ground shipping method. Updated packaging.
BT2.0 Connector - the most significant revolution in 1S Whoop Drone. Since February 2019, we've got some feedback on Facebook about how eager they need the high-quality solid pins connector on 1S whoop drone. So we started our long-term investigation on the design of the solid pins and the stable manufacturing technique to meet pilots' demands. BETAFPV always keeps moving forward with a passion for breakthrough experiences.After BT2.0 300mAh 1S battery, BT2.0 450mAh 1S battery is following close at its heels. As the first 450mAh 1S battery with a BT2.0 connector in the current market, it has an exclusively designed BT2.0 connector, which has broken through the bottle-neck of the PH2.0 crappy crimped pins. What's more, it is highly recommended for Emax Tinyhawk, which achieved dynamic balance, longer flight time, and better performance, just need to simply modify its connector to BT2.0 connector.We also carry 260mAh, 300mAh and 450mAh 1S BT2.0 packs!
Check out all our 1S batteries and all our BetaFPV gear
Features
BT2.0 connector decreased the internal resistance of the connector effectively by upgrading the crimped pins to a 1.0mm banana connector and increasing the cross-sectional area of the 1.0mm banana connector.
BT2.0 300mAh 1S 30C Battery supports 9A continuous current and 15A burst, while the PH2.0 connector supports 4.5A continuous current. With this BT2.0 300mAh 1S battery, all 1S brushless drones will gain powerful and perfect performance.
By solving the problem of voltage sag, the discharge of the 300mAh 1S BT2.0 lipo becomes more efficient. Pilots can enjoy more flight time without the disturbance of low voltage warnings.
Compared with the PH2.0 crimped pins, the BT2.0 connector is more durable and can discharge more currents in the same capacity and provide far more power. You can get a 2mins flight time in full throttle on Meteor65.
Specifications
Item: 1S battery
Capacity: 300mAh
Rate: 30C/60C
Voltage: 4.35V
Dimension: 67.3x11.8x6.1mm
Connector: Betafpv BT2.0 connector
Weight: 8.28g(1pcs)
BT2.0 Connector
There is a graph of comparison between BT2.0 connector and PH2.0 connector (solid pins version) in BETAFPV 1S 260mAh battery. The discharge current is 9A in this testing. You could see that it has longer discharge time and improvement in voltage sag with BT2.0 connector, which brings better flight performance.
Here is Betafpv Lab video to show you the best way to replace PH2.0 to BT2.0 connectors.
Includes
8x BT2.0 300mAh 1S 30C Battery
All batteries must be shipped by a ground shipping method. New Packaging!
After BT2.0 300mAh 1S battery, BT2.0 450mAh 1S battery is following close at its heels. As the first 450mAh 1S battery with BT2.0 connector in the current market, it has exclusive designed BT2.0 connector, which has broken through the bottle-neck of PH2.0 crappy crimped pins. What's more, it is highly recommended for Emax Tinyhawk, which achieved dynamic balance, longer flight time and better performance, just need to simply modify its connector to BT2.0 connector.
BT2.0 Connector - the most significant revolution in 1S Whoop Drone.
We also carry 260mAh, 300mAh and 450mAh 1S BT2.0 packs!
Check out all our 1S batteries and our BetaFPV selection!
Not sure if it's worth to switch BT2.0? Check more from Joshua Bardwell'video- Proof that BT2.0 connector is better than PH 2.0
Since February 2019, we've got some feedback on Facebook about how eager they need the high quality of solid pins connector on 1S whoop drone. So we started our long-term investigation on the design of the solid pins and the stable manufacturing technique to meet pilots' demand. BETAFPV always keeps moving forward with passion for breakthrough experiences.
After BT2.0 300mAh 1S battery, BT2.0 450mAh 1S battery is following close at its heels. As the first 450mAh 1S battery with BT2.0 connector in the current market, it has exclusive designed BT2.0 connector, which has broken through the bottle-neck of PH2.0 crappy crimped pins. What's more, it is highly recommended for Emax Tinyhawk, which achieved dynamic balance, longer flight time and better performance, just need to simply modify its connector to BT2.0 connector.
Features
BT2.0 connector decreased internal resistance of connector effectively by upgrading the crimped pins to 1.0mm banana connector and increasing the cross-sectional area of 1.0mm banana connector.
By solving the problem of voltage sag, the discharge of the 450mAh 1S BT2.0 lipo becomes more efficient. Pilots can enjoy more flight time without disturbance of low voltage warning.
BT2.0 450mAh 1S 30C Battery has stable current/voltage output and high efficiency. All 1S brushless drones will gain powerful and perfect performance with this BT2.0 450mAh 1S battery.
It is perfectly suitable for Emax Tinyhawk, it can provide stable and consistent power, which achieved dynamic balance and longer flight time. Just need to simply modify the PH2.0 connector to BT2.0 connector.
Compared with the PH2.0 crimped pins, BT2.0 connector is more durable which can discharge more currents in the same capacity and provide far more power.
High-end technology to guarantee high quality and consistent performance.
We released BT2.0-PH2.0 adapter cable, which is convenient to charge BT2.0 battery with stock PH2.0 charger. Meanwhile, we also release BT2.0 all-in-one battery Tester & charger for your need.
Specifications
Capacity: 450mAh
Rate: 30C/60C
Voltage: 4.35V
Dimension: 61x15x7.5mm
Connector: Betafpv BT2.0 connector
Weight: 12.7g(1pcs)
Includes
4x BT2.0 450mAh 1S 30C Battery
BT2.0 CONNECTOR
There is a graph of comparison between BT2.0 connector 1S 450mAh battery and Emax 1S 450mAh battery. The discharge current is 11A in this testing. You could see that it has longer time and improvement in voltage sag with BT2.0 connector, which brings better flight performance.
All batteries must be shipped by a ground shipping method.
BT2.0 Batteries are well renowned for delivering excellent performance and durability in 1S whoop drones. It is capable of delivering a discharge rate of 40C (continuous) and 80C (burst). A Larger capacity and stronger power bring more flight time and robust flight performance to 75-85mm whoop drones.
Check out all our 1S batteries and all our BetaFPV gear
BT2.0 connector decreased the internal resistance of the connector effectively by upgrading the crimped pins to 1.0mm banana connector and increasing the cross-sectional area of 1.0mm banana connector.
Resistant to voltage sag, making pilots are able to enjoy more flight time without the disturbance of low voltage warnings.
BT2.0 550mAh 1S Battery has stable current/voltage output and high efficiency. All 1S brushless drones will gain powerful and perfect performance with this BT2.0 550mAh 1S battery.
Compared with the PH2.0 crimped pins, the BT2.0 connector is more durable and can discharge more currents in the same capacity and provide far more power.
It is perfectly suitable for BETAFPV 1S whoop drones that use the BT2.0 450mAh battery, it can provide stable and consistent power, which achieved dynamic balance and more flight time. For example, Meteor75, Meteor75 HD, Meteor75 Pro, Meteor75 Pro HD, Cetus Pro, and Cetus X (double 1S battery in serial).
Specifications
Item: BT2.0 550mAh 1S Battery
Capacity: 550mAh
Rate: 40C/80C
Voltage: 4.35V
Dimension: 69.5x16.2x6.5mm
Connector: Betafpv BT2.0 connector
Weight: 13.99g/pc
Includes
1x BetaFPV 3.8V 1S 550mAh 40C LiHV Whoop/Micro Battery 4 Pack - BT2.0
On the latest version, "OFF" Position is for charging 4.2V.
The new 6 port 1S battery charger from BetaFPV supports PH2.0 and BT2.0 at the same time. The charging is faster when using 30W adapter. Compact, fast-charging, and portable, choosing a 1S battery charger that best suits your needs will no longer be difficult with this 6 Ports 1S charger & adapter.
Check out all our 1S chargers, and our BetaFPV gear!
Features
With BT2.0/PH2.0 two types of battery ports, the charger allows charging BT2.0 and PH2.0 batteries at the same time.
By supporting multi-charging protocols including PD3.0/QC3.0/BC1.2, every port's charging current can reach 1A, which makes charging faster.
This portable 30W Type-C power adapter offers fast, efficient charging at home, or on the go.
The power adapter is compatible with any USB‑C-enabled device, you can also pair it with other devices to take advantage of the fast-charging feature.
Both EU and US adapters are provided for your choice.
Specifications
Input connector: Type-C
Input voltage range: 5-12V
Max input power: 30W
Max input current: 2.5A
Max charging current: 1A (Single-port)
Support battery connector: BT2.0&PH2.0
Charging protocol：PD3.0 / QC3.0 (5V / 9V / 12V) / BC1.2
Battery Type：Lipo 4.2V / LiHV 4.35V
Dimensions：79x46x19mm
Includes
1x BetaFPV 6 Port 1S Charger for BT2.0 & PH2.0
1x User manual
1x USA Power Adapter (Only With AC Adpater Version)
1x Type-C to Type-C cable (Only With AC Adpater Version)
C02 Micro Camera is the lightweight camera customized for those weight sensitive micro whoop drones, like Meteor65, Beta65S, Beta85 pro2, HX100SE. Adapted a 1/4'' CMOS sensor, 2.1mm lens for 1200TVL resolution and excellent latency while minimizing the weight to 1.4g. C02 camera features a JST-0.8 connector, special design in plug-and-play, makes it easy to install without soldering.
This micro camera comes with a micro canopy to protect your camera from a harsh crash!
Be sure to check out all our Micro FPV cameras and our entire BetaFPV selection!
Features
1200TVL High Definition Natural Image
Low Latency
Good Low Light Performance
Plug-N-Play Connector
Wide Input Voltage Range
Specifications
Sensor Type: 1/4" CMOS Sensor
TV System: NTSC
Resolution: 1200TVL
Screen Format: 4:3
Lens : 2.1mm(M7) FOV 160°
Video Out: CVBS
Electronic Shutter Speed: Auto
Min. Illimination: 0.01Lux@1.2F
S/N Ratio: >50db
D-WDR : Auto
Day/Night: Color
Power Requirement: DC 3V~5.5V
Dimension: 13x11mm
Weight: 1.4g
Includes
1x BetaFPV Beta C02 Micro Camera
1x Injection Molded Canopy
4x M1.4x5 Screws
Compared with the Beta75X frame, the Beta75X V2 frame only weighs 5.6g, It is lighter and the gravity center of the V2 frame is more concentrated. Increased the height of the frame loop, props can be completely wrapped by the protective ring. A better choice for a 75mm brushless whoop drone. What's more, the Beta75X V2 Frame is specially designed with two different motor mounting holes that support 1102 and 1103 brushless motors.
Check out all our whoop frames & accessories and all our BetaFPV gear!
Features
The Beta75X V2 frame only weighs 5.6g, it is lighter and the whole drone’s gravity center more concentrated than the Beta75X V1. Meanwhile, the motor mount position uses a quadrilateral stretch structure, makes the frame more durable and stable.
Increased the height of the frame loop, props are completely wrapped by the protective ring, more effectively protected the propellers.
Designed two different motor mounting holes that support 1102 and 1103 brushless motors at the same time.
With a 26mm*26mm FC mounting columns can match whoop style flight controllers like F4 AIO 12A FC. The battery slot fits BETAFPV 300mAh 2S and 300mAh 3S-S battery.
Specifications
Diagonal motor to motor distance: 75mm
Motor mounting hole: for both 3 and 4 hole motors
FC mounting hole: 26mm x 26mm, fully compatible with whoop style FC board mounting pattern
Battery slot size: 6.8x16.1mm
Material: Plastic
Weight: 5.6g
Includes
1x BetaFPV Beta75X V2 Whoop Frame - Choose Your Color
All batteries must be shipped by a ground shipping method.
Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Meanwhile, it supports the Betaflight configurator which is a popular application to configure RC aircraft.
Check out our other RTF combos, all our pre-built quads and our BetaFPV selection!
Features
An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system.
Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoor.
Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and 2xBT2.0 450mAh 1S 30C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight.
Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop & impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots.
Specifications
Item: Cetus X Brushless Quadcopter
Weight: 55g
Wheelbase: 95mm
FC: F4 1S 12A FC V2.2 (ELRS 2.4G)
Motors: 1103 11000KV Motor
Props: Gemfan 2020 4-Blades Props
Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4)
Camera Adjustable Angle: 0°-40°
Receiver Protocol: ELRS 2.4G
VTX: M04 25-400mW VTX
Battery: 2*BT2.0 450mAh 1S 30C Battery
Flight time: 5 mins
Downloads
FC Firmware and ESC download
Includes
1 x Cetus X Brushless Quadcopter
1 x BT2.0 Battery Charger and Voltage Tester
2 x BT2.0 450mAh 1S 30C Battery
1 x Phillips Screwdriver
1 x Prop Removal Tool
1 x Type-C Adapter
4 x Gemfan 2020 4-Blades Props
All products with batteries must be shipped by a ground shipping method.
Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right powerful performance. BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate a bigger battery.
Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features
The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks.
It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.
Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better.
Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board.
The various colors of the spare parts including the Meteor75 Pro frame and Micro
Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals.
HD Digital VTX System
HDZero Nano Lite Camera is designed for feather-lite drones where every gram counts. At a weight as low as 1.5g, combined with the new Whoop Lite VTX at 4.5g with 0.4g dipole antenna enables a world’s-first production digital FPV solution of about 7g. The HDZero Whoop lite Bundle supports 1-3S power input with 25mW/200mW RF power and is capable of recording in 720P/60FPS with super low latency of less than 19ms. What's more, pilots can activate and configure its OSD function on Betaflight Configurator.
Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75 Pro HD (ELRS)
Meteor75 Pro HD (Frsky, PNP, TBS)
FC Inside
F4 1S 5A FC (Serial ELRS 2.4G) V2.0
F4 1S 5A FC (SPI Frsky) V3.0
Gyro
BMI270
BMI270
FC Firmware
BETAFPVF411
BETAFPVF411RX
UART Port
One UART Port
Two UART Ports
External RX
Not Supported
Supported
Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD.
Micro Canopy Lite
Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone.
Endurance Boosting Battery
With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots.
Meteor HD Series
BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images.
Meteor75 Pro Frame
Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately.
Powerful 1S Drone Combo
Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots.
Specification
Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX)
Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero)
Camera Adjustable Angle: 0-40°
Motors: 1102 22000KV Motor
Battery: BT2.0 550mAh 1S Battery
Frame: Meteor75 Pro Brushless Whoop Frame
Propellers: Gemfan 45mm 3-Blade Propellers
Canopy: BETAFPV Micro Canopy Lite
Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero)
Receiver: Serial ELRS 2.4G/SPI Frsky/TBS
FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle
Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera
FAQ
Download the FC firmware and CLI dump file for Walksnail and HDZero version.
Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit.
Click to download the manual for HDZero Whoop Lite Bundle.
Includes
1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver
2x BT2.0 550mAh 1S Battery
1x Type-C USB Cable
1x BT2.0 Battery Charger and Voltage Tester
4x 45mm 3-Blade Props (1.5mm Shaft)
1x Screwdriver
1x VTX USB Cable (Walksnail or HDZero Version)
1x Pack of Screws
All products with batteries must be shipped by a ground shipping method.
Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right power performance. BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate a bigger battery.
Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP.
Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection!
Features
The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks.
It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.
Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better.
Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board.
The various colors of the spare parts including the Meteor75 Pro frame and Micro
Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it.
Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals.
HD Digital VTX System
The Walksnail Avatar HD Mini 1S Lite uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 7.8g lightweight, compatible with 1S whoop drone. Built-in 8 GB storage, this VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode, Betaflight full OSD display is supported and can be adjusted easily by remote control.
Note: Please make sure that the battery voltage must be 3.1V at least when flying, otherwise, the HD digital VTX would stop working.
Flight Controller
The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC.
Meteor75 Pro HD (ELRS)
Meteor75 Pro HD (Frsky, PNP, TBS)
FC Inside
F4 1S 5A FC (Serial ELRS 2.4G) V2.0
F4 1S 5A FC (SPI Frsky) V3.0
Gyro
BMI270
BMI270
FC Firmware
BETAFPVF411
BETAFPVF411RX
UART Port
One UART Port
Two UART Ports
External RX
Not Supported
Supported
Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD.
Micro Canopy Lite
Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone.
Endurance Boosting Battery
With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots.
Meteor HD Series
BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images.
Meteor75 Pro Frame
Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately.
Powerful 1S Drone Combo
Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots.
Specification
Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX)
Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero)
Camera Adjustable Angle: 0-40°
Motors: 1102 22000KV Motor
Battery: BT2.0 550mAh 1S Battery
Frame: Meteor75 Pro Brushless Whoop Frame
Propellers: Gemfan 45mm 3-Blade Propellers
Canopy: BETAFPV Micro Canopy Lite
Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero)
Receiver: Serial ELRS 2.4G/SPI Frsky/TBS
FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle
Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera
FAQ
Download the FC firmware and CLI dump file for Walksnail and HDZero version.
Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit.
Click to download the manual for HDZero Whoop Lite Bundle.
Includes
1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver
2x BT2.0 550mAh 1S Battery
1x Type-C USB Cable
1x BT2.0 Battery Charger and Voltage Tester
4x 45mm 3-Blade Props (1.5mm Shaft)
1x Screwdriver
1x VTX USB Cable (Walksnail or HDZero Version)
1x Pack of Screws
All products with batteries must be shipped by a ground shipping method.
Experience super clear and sharper images with the BETAFPV Meteor85 HD. Based on the newest Meteor85 (2022), it comes with Walksnail Avatar Mini HD VTX or HDZero Whoop Lite Bundle, bringing conspicuous images and exceptional visuals to your eyes and capturing details that make the footage look as exciting as the flight. Together with 1103 11000KV motors and GF2015 2-blade props that feature strong propulsion, it gives pilots powerful and impressive results. Enjoy an immersive flight experience for freestyle tricks outdoors, and get the perfect shots with the new HD VTX system.
Features
Lightweight for 52.57g (Walksnail) and 48.30g (HDZero) whoop drone, this new 2S whoop drone with Walksnail HD VTX or HDZero VTX gives pilots an immersive flight experience and impactful visuals.
New frame with the low profile of the battery slot, the drone's gravity center is reduced and improved the sense of compactness, perfectly enhancing the trust-to-weight ratio. It is durable and light enough, giving pilots a good balance of weight and a nice punch on a 2S battery.
Featuring an upgraded propulsion system and a larger capacity battery. Meteor85 uses GF 2015 2-Blade props with 1103 11000KV motors, which gives full play to the efficiency of the power. Combined with a 450mAh 2S battery, Metero85 can fly up to 6 mins (HDZero) and 5 mins (Walksnail).
Adopted with injection molding technique, this canopy is 2.50g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
Reserve solder pads for the external receivers with UART1 and UART2 on F4 1-2S 12A FC board. The SPI ELRS 2.4G and SPI Frsky version can be used as PNP quadcopter.
Specifications
Frame: Meteor85 Brushless Whoop Frame
Motors: 1103 11000KV Motors
Props: Gemfan 2015 2-Blade Propellers
Receiver: ELRS 2.4G
VTX: 1S Walksnail Avatar Mini HD VTX or HDZero Whoop
Battery: 450mAh 2S Battery
Weight Without Battery: 52.57g (Walksnail)/48.30g (HDZero)
Flight Time: 6 mins (HDZero)/5 mins (Walksnail)
Camera Adjustable Angle: 0-45°
FC&ESC: F4 1-2S 12A FC (2022)
VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero)
Camera: Walksnail Avatar Nano Camera/HDZero Nano Lite Camera
Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM
F4 1S 12A AIO FC
CPU: STM32F411CEU6 (100MHZ )
Gyro: Six-Axis BMI270 (SPI connection)
SPI ELRS 2.4G Receiver
Dimensions: 26mm x 26mm (suitable for whoop pattern mounting hole)
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 (ELRS)
Motor Pin Connector: 1.25mm Header Pins
USB Port: SH1.0 4-Pin
Weight: 4.74 g (without power cable and BT2.0 connector)
1S 12A ESC
Input voltage: 1S-2S
Built-in ESC with 12A continuous and peak 25A current
ESC firmware: C_X_30_48_V0.18.1.hex for Bluejay BB51 hardware
Includes
1x Meteor85 Brushless Whoop Quadcopter (2S HD Digital VTX) ELRS 2.4G
1x 450mAh 2S 45C Battery
1x Type-C to SH1.0 Adapter
1x SH1.0 Cable
3x Decorative Parts
4x Gemfan 2015 2-Blade Propellers
1x Walksnail VTX USB Cable (For Walksnail Version)
1x HDZero VTX Converter Cable (For HDZero Version)
1x Pack of Screws
1x User Manual
BT2.0 Connector - the most significant revolution in 1S Whoop Drone!
BT2.0 1S Whoop Connector is an option for you to modify your existing batteries and drones which use the PH2.0 connector. With the 1.0mm banana connectors, it can support 9A continuous current and 15A burst. Makes the best potential of brushless whoop drone, and display the perfect performance of your drone with BT2.0 300mAh 1S battery.Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Not sure if it's worth to switch BT2.0? Check more from Joshua Bardwell'video- Proof that BT2.0 connector is better than PH 2.0
Features
BT2.0 connector decreased internal resistance of connector effectively by upgrading the crimped pins to 1.0mm banana connector and increasing the cross-sectional area of 1.0mm banana connector.
BT2.0 connector supports 9A continuous current and 15A burst, while the PH2.0 connector supports 4.5A continuous current. Brings more perfect flight experience when you fly the 1S brushless whoop drone.
By using the BT2.0 connector, it can solve the problem of voltage sag, the discharge of the 1S lipo battery becomes more efficient. Pilots can enjoy more flight time without disturbance of low voltage warning.
With the light and customized 22AWG wire, it will make the drone more lighter. The wire uses US standard core 0.08mm*60. The diameter of silicone outer layer is only 1.5mm, which is 0.2mm thinner than 22AWG standard wire.
There is a graph of comparison between BT2.0 connector and PH2.0 connector (solid pins version) in BETAFPV 1S 300mAh battery. The discharge current is 9A in this testing. You could see that it has double time (about 2minutes) with BT2.0 connector.
Specifications
Size: Male Connector - 6.0*4.2*10.5mm / Female Connector - 6.0*4.2*8.3mm
Weight: Male Connector- 0.34g/PCS / Female Connector - 0.24g/PCS
Note: The terminal molded case identifies the positive and negative poles, and must be welded according to the instructions.
Includes
5x BetaFPV BT2.0 1S Whoop Connector Male
5x BetaFPV BT2.0 1S Whoop Connector Female
Here is Mr ShutterBug'vedio to show you the way of replacing connectors safely.
BT2.0 Connector - the most significant revolution in 1S Whoop Drone!
BT2.0 1S whoop cable pigtail is an option for you to modify your drone or your 1S FC board which is with the PH2.0 connector. With the 1.0mm banana connectors, it can support 9A continuous current and 15A burst. Makes the best potential of brushless whoop drone, and display the perfect performance of your drone with BT2.0 300mAh 1S battery.Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Not sure if it's worth to switch BT2.0? Check more from Joshua Bardwell'video- Proof that BT2.0 connector is better than PH 2.0
Features
BT2.0 connector decreased internal resistance of connector effectively by upgrading the crimped pins to 1.0mm banana connector and increasing the cross-sectional area of 1.0mm banana connector.
BT2.0 connector supports 9A continuous current and 15A burst, while the PH2.0 connector supports 4.5A continuous current. Brings more perfect flight experience when you fly the 1S brushless whoop drone.
By using the BT2.0 connector, it can solve the problem of voltage sag, the discharge of the 1S lipo battery becomes more efficient. Pilots can enjoy more flight time without disturbance of low voltage warning.
With the light and customized 22AWG wire, it will make the drone more lighter. The wire uses US standard core 0.08mm*60. The diameter of silicone outer layer is only 1.5mm, which is 0.2mm thinner than 22AWG standard wire.
There is a graph of comparison between BT2.0 connector and PH2.0 connector (solid pins version) in BETAFPV 1S 300mAh battery. The discharge current is 9A in this testing. You could see that it has double time (about 2minutes) with BT2.0 connector.
Specifications
Item: BT2.0 1S Whoop Cable Pigtail
Wire Type: 22AWG
Connect: BT2.0 Male Connector
Length: 55mm (Not included the plug)
Weight: 0.91g/pc
Includes
6x BetaFPV BT2.0 1S Whoop Pigtail Cable
How to re-solder your FC pigtail
BT2.0 1S Whoop Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), the white wire is the negative pole(-). When you resolder your board, please pay attention to the connection method.
Here is Mr ShutterBug'vedio to show you the way of replacing connectors safely.
BT2.0 Connector - the most significant revolution in 1S Whoop Drone!
To provide our customers with greatest convenience, we specially made this adapter cable, this adapter cable will be a perfect solution when you want to charge the BT2.0 300 mAh 1S battery with the PH 2.0 charger. We also carry BT2.0 pigtails and connectors for converting your whoops!Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Not sure if it's worth to switch BT2.0? Check more from Joshua Bardwell'video- Proof that BT2.0 connector is better than PH 2.0
Features
Conversion from PH2.0 connector to BT2.0 connector can be achieved with just one Adapter Cable, which convenient for charge the BT 2.0 battery with the PH 2.0 charger.
Specifications
Item: BT2.0-PH2.0 Adapter Cable
Length: 55mm (Not included the plug)
Weight: 1.07g(1 pcs)
Wire Type: 22AWG
Input Port: PH2.0 male connector（connect PH2.0 charger）
Output Port: BT2.0 female connector（connect BT2.0 battery）
Note: Blue represents the positive pole (+); White represents the negative pole(-)
Includes
6x BetaFPV BT2.0 to PH2.0 1S Whoop Adapter Cable
The BT3.0 2S Whoop Connector Female Set 10 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 10 female BT3.0 2S whoop connectors.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
BT3.0 Female Connector: 0.68g/PCS, 10.1x9.1x5.4mm
BT3.0 Male+Female Connector: 1.28g/PCS
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 2S Whoop Connector Female Set 10 Pack
The BT3.0 2S Whoop Connector Male/Female Set 10 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 5 female and 5 male BT3.0 2S whoop connectors.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
BT3.0 Male Connector: 0.6g/PCS, 11.2x9.2x6.1mm
BT3.0 Female Connector: 0.68g/PCS, 10.1x9.1x5.4mm
BT3.0 Male+Female Connector: 1.28g/PCS
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 2S Whoop Connector Female/Male Set 10 Pack
The BT3.0 2S Whoop Connector Male Set 10 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 10 male BT3.0 2S whoop connectors.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
BT3.0 Male Connector: 0.6g/PCS, 11.2x9.2x6.1mm
BT3.0 Male+Female Connector: 1.28g/PCS
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 2S Whoop Connector Male Set 10 Pack
This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 5 BT3.0 whoop cable Pigtails.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
Specifications
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 Male 2S Whoop Cable Pigtail 5 Pack
The BT3.0 2S Whoop adpater Male BT3.0 to HX2.54 cable 5 Pack is designed for 2S batteries, featuring three gold-plated copper metal pins, allowing for balancing power when charging without an additional balancer connector. This simplification of the 2S battery assembly is lightweight, weighing in at 1.28 grams and occupying less space than regular connectors on the market. This presents an easy solution for 2S quad pilots, freeing up a few grams of quad weight in the process. You will get 5 BT3.0 to HX2.54 whoop adapter cables.
Check out all our pigtails, connectors and adapters as well as our range of BetaFPV gear!
Features
An innovative option for 2S whoop drone battery, designed specifically for 2S whoop drones.
The BT3.0 connectors offer unparalleled convenience, combining balance charging and discharge power cord functionalities into a single connector, eliminating the need to purchase an expensive balance charger.
The BT3.0 connectors are smaller and lighter in weight, with a total weight of only 1.28g for both male and female connectors, compared to regular connectors.
The BT3.0 connectors boast a rated discharge current of 12A and an instantaneous current of up to 20A, meeting the discharge requirements of 2S batteries.
BT3.0 Connectors
The BT3.0 connectors are a 3PIN terminal, two metal pins with a diameter of 1.3mm are used for battery discharge, and two metal pins with a diameter of 1.3mm and a metal pin with a diameter of 1.0mm are combined into a 3PIN connector as a balanced charger for battery charging. The BT3.0 connectors have polarity marks on their welding cup but don't support reverse connections. When welding wires, make sure to pay attention to the positive and negative directions. The connector's design prevents reverse connections, so do not force it in the opposite direction to avoid short circuit risks.
When you resolder your board, please pay attention to the connection method. BT3.0 Cable Pigtail is composed of blue wire and white wire. The blue wire is the positive pole(+), and the white wire is the negative pole(-).
BT3.0-XH2.54 Adapter Cable
The BT3.0 connector can serve as a 2S balance charging port and can be used with a conventional 2S balance charger to charge the battery through a BT3.0 male-to-male adapter cable, providing customers with greater flexibility to choose their own charging method.
Specifications
BT3.0 XH2.54 Adapter Cable: 1.84g/PCS, 35mm
Insertion Force: 3-22N
Color: White
Metal Material: Gold-plated copper
Plastic Material: PA9T
Plug Lifespan: 1000 times
Rated Current: 12A
Instantaneous Current: 20A
Includes
1x BetaFPV BT3.0 to HX2.54 2S Whoop Adapter Cable 5 Pack
Check out the C03 FPV Micro Camera, specially designed for indoor micro FPV quadcopters, this micro camera has 1200TVL resolution and 1/3" CMOS sensor getting you a high-quality and clear image. Expect a solder-free, and very convenient installation with this JST-0.8 plug-and-play design, suitable for Meteror series drones. With a Global WDR camera, 4:3 aspect ratio, getting you a clear dynamic picture even in low light conditions. Expect to 2.1mm lens, FOV 160° for beyond the wide angle for recording a more wide and eye-pleasing flight!
Be sure to check out all our Micro FPV cameras and our entire BetaFPV selection!
Features
Included Micro Canopy
1200TVL High Definition Natural Image
Low Latency
Good Low Light Performance
Plug-N-Play Connector
Wide Input Voltage Range
Specifications
Sensor Type: CMOS 1/3"
TV System: NTSC
Resolution: 1200TVL
Screen Format: 4:3
Lens : 2.1mm(M7) FOV 160°
Video Out: CVBS
Electronic Shutter Speed: Auto
Min. Illumination: 0.01Lux@1.2F
S/N Ratio: >50db
D-WDR : Auto
Day/Night: Color
Power Requirement: DC 3V~5.5V
Dimension: 11x14.1x13.5mm
Weight: 1.45g
Includes
1x BetaFPV Beta C03 Micro Camera
1x BetaFPV Micro Canopy w 20°/30° Camera Mounts
4x M1.4x5 Screws
The ND filters are specifically designed for the Pavo Pico Brushless Whoop Quadcopter. Meanwhile, the DJI O3 Air Unit ND Filters are tailored for the DJI O3 Air Unit and are capable of reducing the amount of light that enters the camera lens. With this feature, you can achieve slower shutter speeds or wider apertures when flying.
These lightweight filters are crafted from high-quality optical class ensuring optimal image clarity and are too easy to install on the build.
ND4 Filter: Ideal for dark, cloudy daysND8 Filter: Perfect for cloudy days or early morning/late afternoon sunlightND16 Filter: Suitable for use on bright, sunny daysND32 Filter: Designed for exceptionally bright conditions, such as snow or water reflectionsCPL Filter: Enhances color saturation and contrast by reducing glare from reflective surfacesClear UV Filter: Protects your camera lens from dust, dirt, and scratches
Check out other DJI O3 Products!
Check out the rest of our replacement cam parts & accessories, and all our BetaFPV gear!
Features
DJI O3 filters are easy to install and protect your camera lens from dust, sand, and debris. They ensure uninterrupted high-quality footage during flights and extend the life of your equipment. Customized filters for your drone can enhance your footage and equipment protection.
ND filters reduce sunlight brightness, lower camera shutter speed to avoid overexposure, prevent distortion in high-speed motion blur shots and improve drone footage quality.
UV filters effectively minimize the blue tone caused by ultraviolet rays in outdoor photography, resulting in clearer, more saturated, and more realistic images. They also protect the camera lens from dirt, sand, and scratches.
CPL filters reduce light and mirror reflection, preventing overexposure and white reflections. They improve clarity and brightness, especially over water or reflective surfaces, resulting in a more detailed image with reduced glare.
Installation Methods
The filter supports two installation methods. To install the filter, align it with the lens position and clip it into the frame horizontally or vertically. To remove it, grip the lens mount with your thumb and pull it out.
Horizontal installation of the UV filter is more suitable for shooting ground or scenery as it effectively reduces reflections and scattering, avoiding excessive refraction of light that may affect image quality. It also provides added protection to the camera lens surface, reducing the risk of damage. Vertical installation of the UV filter is best for shooting reflective surfaces such as water or glass, as it better reduces reflections and prevents them from interfering with the shot.
Specification
Item: UV Filter / ND8 Filter / ND16 Filter / ND32 Filter / CPL Filter
Weight: 0.74g
Adapt Camera: DJI O3 Camera
Includes
1x BetaFPV DJI O3 Air Unit Camera Filters - Choose Your ND
BETAFPV Lite receiver is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.Message from BETAFPV regarding Flat antenna range issues:The ELRS Lite Receiver flat antenna V1.1 is coming to see you again. Range issues and failsafe at around 100 meters have been resolved compared with V1.0. Now, the V1.1 flat antenna receiver can reach 600 meters with BetaFPV Moxon antenna. Please feel free to email support@betafpv.com and our support team will help you if you have any issues.
Check out all our receivers, and our entire BetaFPV selection!
Specifications
Input voltage: 5V
Frequency bands: 2.4GHz ISM
MCU: ESP8285
Telemetry power: 17mW
Antenna: Integrated SMD ceramic antenna
Size: 10*10mm
Weight: 0.47g tower or .53g flat (with SMD ceramic antenna)
Note: The firmware version of the Lite receiver manufactured by our company is ELRS 1.1.0; ELRS Innovative team has officially released version 1.2.0, which is not compatible with the 1.1.0 version. We suggest our customers upgrade this receivers' ELRS version to 1.2.0 if needed. Significantly, the TX module and receiver have to be in the same ELRS version, otherwise, the frequency cannot match successfully.
Includes
1x BETAFPV ELRS Lite receiver
2x Spare shrink tube
4x 30awg silicon connection wires (1 black, 1 red, 1 white, 1 yellow)
The BETAFPV Micro RF TX module is based on the Express LRS project, an open-source RC link. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.Check out our RC Transmitters and all our BetaFPV products!
Specifications
Packet refresh rate: 25Hz/50Hz/100Hz/200Hz (915MHz/868MHz),
RF output power: 100mW/250mW/500mW (915MHz/868MHz)
Frequency bands: 915MHz FCC/868MHz EU
Input voltage: 5V~12V
XT30 port: 5V~12V, recommend 2S(8.4V) battery, DO NOT support 3S(12.6V) or above
USB port: Type-C
Note: Please assemble the antenna before power on. Otherwise, the PA chip in the Micro TX module will be damaged permanently.
Note: Please DO NOT use 3S or above battery to power up the TX module via XT30 port. Otherwise, the power supply chip in the TX module will be damaged permanently.
About the firmware
The ExpressLRS offical project on Github does NOT support the OLED function for the moment. BETAFPV team will work with the ELRS team and make the official repository support the OLED and button function ASAP.
Please get the firmware from BETAFPV Github nowadays until ExpressLRS official support. In BETAFPV branch, the ExpressLRS protocol is V1.1.0 and NO binding phrase for the firmware.
NOTE: There are 2 known issues with this firmware currently. We will solve these 2 issues ASAP. If you find more other issue, feel free to leave a issue here.
Only support pressing function for the joystick.
When entering OLED menus page with long pressing, the connection between RF TX module and receiver will be lost, the connection will recover after exiting menus page automatically;
You could all use the ELRS official firmware V2.0-RC2 now, but lost the function of OLED and Joystick. We will work with the ELRS dev team and make the ELRS official firmware support the full function of the Micro TX Module. For the milestone, OLED will be supported in the V2.1 officially.
https://github.com/BETAFPV/ExpressLRS
User manual of How to Flash Firmware of ELRS RX/TX.
Includes
1x BETAFPV ELRS Micro TX module
1x BETAFPV Moxon antenna
1x Micro TX module user manual
1x Spare USB data cable (Type-A to Type-C)
BETAFPV Nano receiver is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
Check out all our receivers, and our entire BetaFPV selection!
Specifications
Input voltage: 5V
Telemetry power: 20dbm (100mW, 2.4G Version)
Frequency bands (Nano receiver 2.4G version): 2.4GHz ISM
Frequency bands (Nano receiver 915MHz/868MHz version): 915MHz FCC/868MHz EU
Antenna Connector: IPEX MHF (IPEX 1 / U.FL)
Size: 12x19mm
Weight: 0.7g (receiver only)
Note: The firmware version of the Nano receiver and module manufactured by our company is ELRS 1.0.0-RC5 (the fifth test version before release);ELRS Innovative team has officially released version 1.0.0. Based on the version, we have some updates:
2.4G Nano TX Module supports 500Hz refresh rate；
Short press the button on the Nano module 3 times to get into the binding status.
We suggest our customers upgrade their modules and receivers' ELRS version to 1.0.0. Significantly, the module and receiver have to be in the same ELRS version, otherwise, the frequency cannot match successfully.
Includes
1x Beta FPV ELRS Nano 2.4GHz Receiver
1x BetaFPV T Antenna
2x Spare Shrink Tube
4x 30awg Silicon Connection Wires (1 black, 1 red, 1 white, 1 yellow)
1x Pin Header 1x4
BETAFPV Nano RF TX module is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
BETAFPV Nano RF module is compatible with radio transmitter which has the nano module bay (AKA lite module bay, e.g. Frsky Taranis X-Lite, Frsky Taranis X9D Lite, TBS Tango 2)
Check out our RC Transmitters and all our BetaFPV products!
Specifications
Packet refresh rate: 25Hz/50Hz/100Hz/200Hz (915MHz/868MHz)
RF output power: 100mW/250mW/500mW
Frequency bands: 915MHz FCC/868MHz EU
Input voltage: 5V-12V
USB port: Type-C
Diagram
Note: Please assemble the antenna before power on. Otherwise, the PA chip in the Nano TX module will be damaged permanently.
Upgrade the Firmware
The stock firmware of the Nano receiver and TX module manufactured by our company is ELRS V1.0.0-RC5 (the fifth release candidate version);ELRS Innovative team has officially released the first major version V1.0.0 on 17th July. It has some updates :
2.4G Nano TX Module supports 500Hz refresh rate;
Short press the button on the Nano module 3 times to get into the binding status.
Includes
1x BetaFPV ELRS Nano 915MHz RC Transmitter Module
1x BetaFPV Moxon Antenna
1x Nano TX Module User Manual
BETAFPV Nano receiver is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
Check out all our receivers, and our entire BetaFPV selection!
Specifications
Input voltage: 5V
Frequency bands: 915MHz FCC/868MHz EU
Antenna Connector: IPEX MHF (IPEX 1 / U.FL)
Size: 12x19mm
Weight: 0.7g (receiver only)
Note: The firmware version of the Nano receiver and module manufactured by our company is ELRS 1.0.0-RC5 (the fifth test version before release);ELRS Innovative team has officially released version 1.0.0. Based on the version, we have some updates:
2.4G Nano TX Module supports 500Hz refresh rate；
Short press the button on the Nano module 3 times to get into the binding status.
We suggest our customers upgrade their modules and receivers' ELRS version to 1.0.0. Significantly, the module and receiver have to be in the same ELRS version, otherwise, the frequency cannot match successfully.
Includes
1x Beta FPV ELRS Nano 915MHz Receiver
1x BetaFPV T Antenna
2x Spare Shrink Tube
4x 30awg Silicon Connection Wires (1 black, 1 red, 1 white, 1 yellow)
1x Pin Header 1x4
This ELRS Recovery Dongle is an FTDI USB to TTL module based on the CP2102 bridge controller, which is applied to the firmware upgrade for the ESP32&ESP8XX chip. The ExpressLRS Recovery Dongle is compatible with many ELRS receivers in the market and FPV goggles backpack. It will be a good choice to unbrick the ELRS receiver when failed in updating or flashing firmware by UART.
Check out our Express LRS collection and all our BetaFPV products!
Features
Unbrick and recover an ELRS receiver when having a failed update such as missing bootloader
Solder Free! This dongle features spring probe pins for more convenient use
Comes inside of a plastic case that is more durable and portable compared with the naked board version on the market.
USB to Serial chip (CP2102) supports XP, win7 / win8 32bits, 64bits, win10 / 11 32bits, 64bits, Linux, MAC
Specifications
Operating Voltage: 5V
Logic Voltage: 5V
3.3V Power Supply Output Current: 400mA
Pins Output Method: 2x4P-2.54mm pin header
Serial Baud Rate: Up to 921600bps.
USB Connector: USB-C
Includes
1x ExpressLRS Recovery Dongle
1x 4 Pin Cable
1x Probe Converter Board
The BetaFPV F4 1S 12A AIO Brushless Flight Controller V2.2 is the default FC for Cetus X brushless whoop quadcopter, also great for 85mm whoop drones like Meteor85 and 3" toothpick drones like HX115 SE Toothpick Drone and HX115 LR Toothpick Drone. BetaFPV updated the FC to V2.2 with BMI270 gyro and BB51 ESC hardware in place of ICM20689 gyro and BB21 ESC hardware.
Check out all our whoop flight controllers, and all our BetaFPV gear!
Specifications
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: BMI270
Built-in Receiver: SPI ExpressLRS 2.4G / Frsky SPI
Receiver antenna: Line antenna
Size: 30mm x 30mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.1_BETAFPVF4SX1280 (ELRS)
OSD: Built-in BetaFlight OSD
Recommend VTX:
Power Cable: 55mm, with BT2.0 connector
Weight: 3.6g (Without power cable included)
Power supply: 1S-2S
Current: 12A continuous and peak 25A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: C_X_30_REV16_7.hex for BB51 BLHeli_S hardware
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Includes
1x F4 1S 12A AIO FC
Wiring Diagram
The ultralight F4 1S 5A AIO Brushless Flight Controller is back in stock with new and upgraded features. Compared to the previous version, the new board uses Serial ExpressLRS 2.4G instead of SPI ELRS 2.4G so that it can support ExpressLRS V3.0 and also has a Frsky RX version to choose from. We updated the FC with high-quality BMI270 gyro and BB51 ESC hardware. In addition, this new board supports the Betaflight Blackbox function.
Check out all our whoop flight controllers, and all our BetaFPV gear!
Specifications
CPU: STM32F411CEU6 ( 100MHZ )
Six-Axis: BMI270
Built-in Receiver: Serial ExpressLRS 2.4G / Frsky SPI
Receiver antenna: Line antenna
Size: 30mm x 30mm, fully mounting pattern compatible with the whoop frame in the current market
Firmware version: betaflight_4.3.1_BETAFPVF411
OSD: Built-in BetaFlight OSD
Recommend VTX:
Power Cable: 55mm, with BT2.0 connector
Weight: 3.6g (Without power cable included)
Power supply: 1S
Current: 5A continuous and peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: A_X_5_.HEX for BB51 BLHeli_S hardware
Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Includes
1x BetaFPV F4 1S 5A Toothpick/Whoop Flight Controller - Choose Version
4x M1.2x4mm Screws
4x M1.4x5mm Screws
4x Anti-vibration Rubber Dampers
Wiring Diagram
The BetaFPV V1 F4 2-3S AIO is the perfect choice for modern Whoop/Toothpick builds. Featuring an F4 AIO Flight Controller and 20A 4-in-1 ESC with ELRS serial, this setup guarantees smooth, consistent performance. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option.
Note: If you use the F4 2-3S 20A AIO FC V1, the serial port of the SBUS receiver is UART5Check out all our whoop flight controllers, and all our BetaFPV gear!
Features
Designed for HD VTX, it features a dual 9V@2A for DJI O3 and 5V@3A for external device BEC solution to prevent screen blackout on the DJI O3 due to low voltage during throttle increase.
It includes a new DJI O3 6-pin PMU for easy installation without soldering, reducing assembly complexity. Newbie friendly.
The power range of 2-3S provides increased thrust and improved control with a 20A ESC featuring a single NMOS for continuous current capability.
The upgraded onboard receiver allows selective power cutoff for saving power and offers additional UART TX3 and RX3 ports for connecting the external device.
The redesigned solder pad layout ensures larger, more secure pads for easy and reliable soldering, while the relocated USB port at the rear facilitates computer tuning.
It features an STM32F405RGT6 chip, Integrate Serial ELRS 2.4G receiver, 16M black box, barometer, current meter, reserve 3 complete serial ports and a standard SBUS, support GPS, HD VTX, external receiver, and other equipment.
F4 2-3S 20A AIO FC V1 also has extended the USB port to the end for easier parameter adjustment and wiring. And a new DJI O3 6-pin PMU has been added for convenient installation and maintenance.FAQPower cutoff: Removing the chip bead disconnects the power supply, and to reuse the onboard ELRS receiver, soldering the solder pads together restores power.UART3 release: Removing two resistors on the solder pads releases UART3. The left side is TX3, and the right side is RX3. To reconnect, solder the solder pads together when reusing the onboard ELRS receiver.Voltage Switch: The HD VTX connector defaults to 9V. The chip bead is soldered between the 9V pad and the middle pad. To use WalkSnail Avatar HD mini 1s and Lite, please ensure the power supply voltage is 5V. Remove the chip bead first from the 9V pad and solder it between the middle pad and the 5V pad. Alternatively, you can use solder instead the chip bead to switch between the 5V and 9V pads.Motor choice: Avoid selecting motors with excessively high KV ratings, as motors above 20,000KV are prone to burn.Betaflight Firmware and CLIFC firmware: Betaflight_4.4.1_BETAFVF405Download the firmware and CLI dump fileReference link:https://github.com/betaflight/betaflight/releases/tag/4.4.1ESC FirmwareWith BB51 ESC solution, F4 2-3S 20A AIO FC V1 is based on BLHeliSuite16714903 with Bluejay ESC firmware, it supports bidirectional D-shot and RPM filtering in Betaflight, offers 24KHz, 48KHz, and 96KHz fixed PWM frequency for options, and custom start-up melodies. F4 2-3S 20A AIO FC V1 default factory setting is 48KHz and it doesn’t recommend upgrading the 96KHz, or it might cause an error in the motor idle setting, not spinning when disarmed.DO NOT flash the firmware with a shorter interval, otherwise, there will be a certain chance of stalling and burning the flight controller.ESC-Configurator: https://preview.esc-configurator.com/Download BLHeliSuite16714903Download the Bluejay ESC firmware. Please choose C_X_70.HEXConnecting External DevicesPlease note that the board reserves two serial ports and a standard SBUS port, which is available for the external CRSF protocol receiver or GPS module, and SBUS protocol receiver. You can refer to the below picture.
Specifications
Weight: 5.58g (without motor connectors and power cable), 5.92g (with motor connectors)
Mounting Hole Size: 26mm x 26mm
CPU*: STM32F405RGT6 (168MHz)
Six-Axis: ICM42688P (SPI connection)
RX: Serial ELRS 2.4G Receiver
RX firmware version: BETAFPV AIO 2400 RX ELRS V2.5.2
Antenna: Enameled wire
Blackbox Memory: 16MB
Sensor: Barometer(BMP280), Voltage&Current
5V BEC*: 5V 3A@8V supply
9V BEC*: 9V 2A@8V supply
USB Port: SH1.0 4-Pin
Built-in ESC with 20A continuous and peak 25A current
ESC input voltage: 2-3S
FC firmfware version: Betaflight_4.4.1_BETAFPVF405
ESC firmware: C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware
Signal support: D-shot300, D-shot600
Includes
1x BetaFPV V1 F4 2-3S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ELRS Serial
Wiring Diagram
Based on the F405 2-4S 20A Flight Controller V4, the F405 4S 20A Toothpick Flight Controller V5 applies a new ICM42688 gyro and ESC chip that comes with BLUEJAY ESC firmware so it supports bidirectional D-shot. In addition to plug-and-play ports for the receiver and HD Digitial VTX, the same as the V4 board, the V5 board is made with a more rational layout for easy solder and preventing solder from jumping to another pad and shorting components.
Check out all our whoop flight controllers, and all our BetaFPV gear!
Features
Not only is the flight controller board made with a rational layout, but it is also designed with larger solder pads. It is very easy for pilots to solder external electronics.
The flight controller is capable of handling 20A continuous current and reaching 25A peak current due to high-quality MOSFETs.
Soldering motor wires to the pad directly allows lower resistance for more current on motors. Besides, solder pads are reinforced by thick copper and edge plating processes, ensuring a solid value and durable use.
Reserving the UART ports layout, UART3 for RX, UART4 for HD digital VTX, UART6 for Analog VTX, and UART1 for spare use, it is more convenient for pilots to solder.
This board comes with a 25.5x25.5mm whoop mounting pattern; this board can be added to both the toothpick drone and the cinematic whoop quadcopter
Note: F405 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLUEJAY firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it.
Comparison to F405 2-4S 20A V4 FC
We upgraded the F405 2-4S 20A V4 board to V5 by adopting ICM42688 gyro instead of MPU6000 and adding some new features. ICM42688 gyro works great in most cases. Except for the gyro, the V5 board comes with a completely new ESC firmware that supports bidirectional D-shot. The way to connect motors changed and is solderable only on the V5 board. Besides the V5 FC board features high-quality material for stability and durability. The below pictures show the difference between the two flight controllers.
Note: The F405 2-4S 20A Flight Controller V4 with BMI270 gyro will be available for purchase for a period of time.
Diagram for Toothpick F405 20A AIO FC V5
The board integrates 2 LEDs, including the Power LED (Red) and the FC LED (Blue).
LED
Status
Description
Power LED (Red)
Solid
Power on
FC LED (Blue)
Solid
Motor Armed
Connecting External RX/HD Digital VTX
F405 4S 20A FC V5 integrates the Plug & Play port for the external RX and HD digital VTX, and there will be a 4-pin connector for RX and a 6-pin connector for HD digital VTX in the package. Thus, we highly recommend pilots use the port to save the solder work.
FC & ESC Firmware:
The default firmware is including CLI dump file. But if you flash firmware from the Betaflight configurator official site, please flash a CLI dump file for F405 4S 20A FC V5. We offer the default firmware and CLI dump file to download.
Download the FC default firmware betaflight_4.3.1_BETAFPVF405 and CLI dump file.
F405 4S 20A FC V5 is available to flash both BLHeli_S and BLUEJAY ESC firmware and it comes with default BLUEJAY firmware. The main difference is that the BLUEJAY firmware supports bidirectional D-shot, while BLHeli_S does not support it. Here are the download links for two firmware.
Here are the download links for ESC firmware. Please configure the BLUEJAY firmware through ESC - Configurator or Bluejay Configurator software.
Download the BLUEJAY ESC firmware
Download the ESC - Configurator
Download the Bluejay Configurator
We offer BLHeli_S ESC firmware for pilots. Please configure the BLHeli_S ESC firmware through BLheliSuite, BLHeli - Configurator, or ESC - Configurator software.
Download the BLHeli_S ESC firmware
Download the BLHeliSuite16714902a
Download the BLHeli - Configurator
Download the ESC - Configurator
frame like Pavo25 and X-knight 35.
Specifications:
Flight Controller
CPU: STM32F405RGT6
Six-Axis: ICM42688 (SPI connection)
Mounting Size: 25.5x25.5mm (M2 Anti-vibration rubber damper available)
FC Firmware: betaflight_4.3.1_BETAFPVF405
OSD: Built-in Betaflight OSD (OSD chip: AT7456E)
Receiver: SBUS/CRSF/DSMX Receiver
BEC: 5V 3A
Built-in current sensor
Weight: 8.35g
ESC
ESC Chip: SILABS EFM8BB21F16G-C
Support D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
Input voltage: 2S-4S Lipo
Continuous current: 20A
Peak current: 25A
Firmware: G_H_20_48_v0.16.HEX (Default BLUEJAY), BLHeli_S (Optional)
Includes
1x BetaFPV F405 V5 2-4S AIO Whoop/Toothpick Flight Controller (w/ 20A 8Bit 4in1 ESC) - ICM42688
1x Cable Pigtail (XT30)
1x 6-Pin Connector for Digital VTX
1x4-Pin Connector for RX
4x M2x12 Screws
8x M2 Nuts
4x M2 Anti-vibration Rubber Dampers
F722 2-6S AIO 35A FC is a very reliable FC that is made to meet your advanced FPV needs. Comes with an F722 chip and a BLHeli_32 ESC, this board provides a better performance capability and higher calculation speed, which brings pilots a more stable and smoother flight. What's more, F722 AIO FC has specially added a 6-pin connector for DJI Digital VTX, just plug & play, less solder work needed, super easy to install. It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery.
Check out all our whoop flight controllers, and all our BetaFPV gear!
A very in-depth video on the BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller.
Features
Built-in STM32F722RET6 CPU, F722 FC is more powerful than F4. It features a fast processing speed and stable performance, providing reliable and smooth flight for 4"-5" drones.
F722 AIO 35A FC has specially added a 6-pin connector for HD Digital VTX, just plug & play, less solder work needed, perfect for the pilots who enjoy the HD Digital VTX system.
6 full UARTs are available on this board. With plenty of UARTS, Pilots could have more options for external parts like VTX, GPS, Receiver, and other components.
It can handle 35A continuous current (40A burst), supports the 2-6S lipo battery, and gives the drone a more robust flight performance.
With the 6S battery and this F722 35A AIO FC, the drone will break through the limit of the power of the toothpick drone, exploring more possibilities in 4-5'' drones.
The new BLHeli_32 ESC version is built-in a 16MB flash memory chip dedicated to Blackbox logging, which is an extremely powerful tool for tuning and troubleshooting an FPV drone. It has a faster processing speed and up to 128k PWM frequency, providing a more stable and smoother flight for pilots.
V2 with BLHeli_32 ESC
V1 with BLHeli_S ESC
PWM Frequency
24k-128k
24k-96k
ESC Firmware
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
Blackbox
16MB
Not included
Weight
9.00g
7.06g
Board Thickness
1.6mm
1.4mm
BLHeli_32 ESC Firmware
The F722 35A AIO FC has two boards with different ESC versions for choice. The V2 board uses AT32F421G8U7 MCU, a 32-bit ESC chip, with BLHeli_32 ESC firmware. This firmware supports up to 128k PWM frequency, featuring faster processing speed and unlocking more functions for the flight.
BLHeli_32 ESC
BLHeli_S ESC
MCU
AT32F421G8U7
EFM8BB21F16G-C
Firmware Version
BLHeli_32.9, 32-bit
BLUEJAY V0.16, 8-bit
PWM Frequency
24k-128k
24k-96k
Bidirectional DSHOT
Support
Support
Signal Support
PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Know More About ICM42688 Gyro
The F722 FC ICM42688 version has the same solder pad and layout as BMI270 except for the gyro chip. Besides, you can also find the difference in Betaflight settings.
The ICM42688 gyro supports 8.00 kHz gyro update frequency compared with the BMI270 gyro which supports 3.20 kHz. When using a 6S battery, the ICM42688 gyro has a good performance.
The degree between ICM42688 and BMI270 gyro is different. When configuring F722 FC ICM42688 version, the gyro degree should be set to CW270°.
Diagram for F722 35A AIO FC
The below picture is the top front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
The below picture is the bottom front of the F722 35A AIO Brushless FC. (Both V1 and V2 boards have the same solder pad and connector ports.)
There are 2 LEDs on the bottom of the board to indicate the status, including the FC LED (Blue) and FC Power LED (Red). The LED status for V1 and V2 boards are the same.
LED
Status
Description
FC LED (Blue)
Solid
Armed
FC LED (Blue)
Extinguished
Disarmed
Power LED (Red)
Solid
Power on
How to Connect the External RX&VTX
To connect the external RX&VTX, please refer to the below diagram. F722 35A AIO V1 and V2 boards have the same soldering pad and connecting ports.
Specifications
Flight Controller
Item: F722 35A AIO Brushless Flight Controller
Weight: 9.00g (BLHeli_32)
CPU: STM32F722RET6
Six-Axis: ICM42688
Mounting hole size: 26mmx26mm
Firmware version: betaflight_4.3.0_STM32F7X2
OSD: Built-in BetaFlight OSD (OSD chip: AT7456E)
Support programmable LED like WS2812 etc
Built-in current sensor
Blackbox: 16MB (V2 with BLHeli_32 ESC included)
ESC
Signal support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/Flysky Receiver/DSMX Receiver/TBS Crossfire Receiver (requires external connection)
Input voltage: 2S-6S Lipo
Continuous current: 35A
Peak current: 40A
ESC firmware: BETAFPV_35A_V2_BLHeli_32_Multi_32_9 (BLHeli_32)
Indicators: Power indicator (Red) / FC indicator (Blue)
Capacitance: CS|5*10*13mm|470μF|35V
Connector: 80mm 14AWG silicone cable with XT60
Recommended motors: 14XX series, 15XX series, 16XX series, 18XX series, 20XX series
Includes
1x BetaFPV F722 V2 2-6S AIO Whoop/Toothpick Flight Controller (w/ 35A 32Bit 4in1 ESC) - ICM42688
Take your drone racing to the next level with BetaFPV's Gemfan 1406 Tri-Blade 35mm Micro/Whoop Prop 4 Pack. With a 1.5mm shaft and 3-blade design, you'll enjoy increased power and quicker speed. Make sure you're always ready to fly with this reliable and efficient prop. The 3-Blade props feature high efficiency and are precise in operation for freestyle.
Check out all our Micro Props and BetaFPV gear, as well as all of our Gemfan products!
Specification
Color: White, Blue, Orange, and Clear Gray
Product material: Clear Plastic
Inner diameter: 1.0mm Shaft
Weight: 1.23g (4pcs)
Includes
1x BetaFPV Gemfan 1406 Tri-Blade 35mm Micro/Whoop Prop 4 Pack (1mm Shaft) - Choose Your Color
Take your drone racing to the next level with BetaFPV's Gemfan Ducted 1815 Bi-Blade 45mm Micro/Whoop Prop 4 Pack. With a 1.5mm shaft and 2-blade design, you'll enjoy increased power and quicker speed. Make sure you're always ready to fly with this reliable and efficient prop. The 2-Blade props feature high efficiency and are precise in operation for freestyle.
Check out all our Micro Props and BetaFPV gear, as well as all of our Gemfan products!
Specifications
Material: PC
Weight: 1.30g/set (2-Blade)
Blades: 2-Blade
Pitch: 1.5 inch
Propeller Diameter: 45mm
Shaft: 1.5mm
Includes
1x BetaFPV Gemfan 1815 Bi-Blade 45mm Micro/Whoop Prop 4 Pack (1.5mm Shaft) - Choose Your Color
Take your drone racing to the next level with BetaFPV's Gemfan 1815 Tri-Blade 45mm Micro/Whoop Prop 4 Pack. With a 1.5mm shaft and 3-blade design, you'll enjoy increased power and quicker speed. Make sure you're always ready to fly with this reliable and efficient prop. The 3-Blade props give more power and faster speed for racing.
Check out all our Micro Props and BetaFPV gear, as well as all of our Gemfan products!
Specifications
Material: PC
Weight: 1.69g/set (3-Blade)
Blades: 2-Blade/3-Blade
Pitch: 1.5 inch
Propeller Diameter: 45mm
Shaft: 1.5mm
Includes
1x BetaFPV Gemfan Ducted 1815 Tri-Blade 45mm Micro/Whoop Prop 4 Pack (1.5mm Shaft) - Choose Your Color
Disassemble at your own risk, we are not responsible for any damage to your camera!
Plastic injection molded GoPro Lite case from BetaFPV. BEC board is optional and also has an adapter for the BetaFPV ND16 Filter for GoPro Lite
This case and BEC board fit the GoPro HERO6 and GoPro HERO7 Black. But NOT for GoPro HERO8.
Check out all our replacement cam parts & accessories and all our BetaFPV selection!
Features
Plastic injection molded,
Easy assembly
Lightweight
Specifications
Weight: 6.57g
Output: 5V@2A
Voltage: 2-4S
Includes
1x BetaFPV GoPro Lite Case V2 for Naked GoPro
1x BEC Board
Instructions for Assembly
How to Assemble
Step 1: Assemble the BEC board on the GoPro motherboard.
Step 2: Hold the camera lens and the camera board at the same time, be careful when you assemble the board on the case.
Step 3, 4: Screw the GoPro motherboard with the M1.4*5 and M1.4*8screws as shown below
Step 5: Install the light pipe as shown below.
Step 6: Install the back case, and screw the board with M1.4*8 screws as shown below.
How to Disassemble GoPro HERO6 Black
Special thanks to JONAH BLAESER who provided the method of disassembling GoPro HERO6 Black. If you are interested, please check the link to know the specific steps to make your own naked GoPro.
GoPro HERO6 Black Disassembly Guide
We also provided the method of disassembling GoPro HERO8 Black. If you are interested, please check the link.
GoPro HERO8 Black Disassembly Guide
Note: Do this at your own risk. You will lose your GoPro’s warranty and you may end up bricking the camera if something goes wrong. This guide is not authorized by GoPro and your camera is not guaranteed to work afterward.
Spare replacement props for the BetaFPV HX115 and HX115 HD.
Check out the rest of our HX115 parts & accessories and our BetaFPV selection!
Specifications
Material: Poly Carbonates
Length: 3 inches, about 76.2mm
Color: Randomly 4 colors, Black, Blue, Transparent Red, Transparent Purple, Transparent Green
Mounting hole: 1.5mm
Weight: 1.5g(1 pcs), 6g (4 pcs)
More Power, Control, and Speed for 2-3 inch sized FPV Micro Racing Drones
Includes
4x BetaFPV HQ 3030 Tri-Blade 3" Prop 4 Pack
1x Mounting Screw Set
The safety handbag is stitched together with an extremely strong fire retardant thread and has a double-zipper lid. It offers extra protection for your lipo battery, micro drone, and your charging location, which could protect your home and valuables from a fire due to a lipo battery failure. Useful for storage, travel, and charging.
Check out all our battery chargers & accessories, and our BetaFPV gear!
Features
Waterproof, fireproof, and radiation protection
Large space to place multiple batteries
Middle spacer, battery can be classified
Double zipper, makes the lipo safe bag well-sealed and convenient to use
This flame retardant bag is a convenient way of safeguarding your Lipo batteries during charging, transit, and storage
Specifications
Color: Black
Dimension: 165*90*120mm
Weight: 130g
Application: For safer charging and storage of Lipo batteries and drone
Material: Textile Fiberglass Material with Fire retardant coating
Includes
1x LiPo Battery Drone Safety Handbag
All products with batteries must be shipped by a ground shipping method.
The Beta FPV LiteRadio 3 Radio Transmitter is the newest remote control in the LiteRadio series. This transmitter features an ergonomically designed handle and has superb performance in its working time and newly updated gimbals. Besides, this version supports BETAFPV Configurator which is a utility designed to simply update, configure, and tune the radio controller.
Check out our RC Transmitters and all our BetaFPV products!
Features
8 channels in total
USB Joystick support for most practice simulators
Nano module bay for external TX module
Newly designed joystick gimbal for longer usage life
Support BETAFPV Configurator for updating, configuring, and tuning
Built-in 2000mAh battery and USB charge supported
Specifications
Frequency Range: 2.4GHz
Channels: 8
Support Protocol: Futaba S-FHSS/Frsky FCC D16/Frsky LBT D16/Frsky D8 or ExpressLRS 2.4G
Power: ELRS version 25mW/50mW/100mW, Frsky version 100mW
Support USB Charging / Firmware Update: Yes
LED Light: Green-Power On / Red-Warning if the voltage is lower than 3.5V / Blue-Normal
Battery: 1S 2000mAh
Charging Connector: USB 3.0 Type-C
Includes
1x BetaFPV Lite Radio 3 2.4GHz RC Transmitter
All products with batteries must be shipped by a ground shipping method.
After the latest round of beta testing, the LiteRadio 2 SE is back to the market with huge improvements. This pint size FRSKY radio is powered by OpenTX firmware and can toggle between FRSKY D16 and D8 protocols. Real gimbals provide the tactile feedback of a pricier radio and USB connectivity can be used to play FPV simulators on a computer. The LiteRadio 2 SE is a great option for anyone looking for a lower cost radio with some great features.
Some new improvements include...
Built-in 1000 mAh 1S battery, LiteRadio 2 SE increases the endurance to 8 hours.
Updates with BETAFPV self-developed LiteRadio System. Pilots can directly operate the Joystick Calibration and Upgrade Firmware on the radio transmitter.
Supports Frsky D8, Frsky D16 FCC and Frsky D16 LBT mode via the radio transmitter.
Comes with 100mW transmitting power, LiteRadio 2 SE brings a wider operating range.
Check out our RC Transmitters, our FrSky Products, and all our BetaFPV products!
This radio does not support newer FrSky receiver firmware.
Features
LiteRadio 2 SE upgrades with BETAFPV self-developed Customized LiteRadio System. Pilots can directly operate the Joystick Calibration and Firmware Update on the radio transmitter, which is more convenient for the beginner racer to operate.
Equipped with a built-in 1000 mAh 1S battery, LiteRadio 2 SE can use up to 8 hours, bringing an excellent endurance performance.
Comes with a built-in charging module, LiteRadio 2 SE can support USB charging which is more convenient to use. Meanwhile, it designs a Low-Power warning to indicate a low battery. While it needs to be re-charged, the blue light will flash slowly.
Compared with the LiteRadio 2, LiteRadio 2 SE has a larger transmitting power which can reach 100mW, bringing a wider operating range.
Adopted the rubber coat, LiteRadio 2 SE is ergonomic and has the shape of a gaming controller. It's comfortable to hold, and the anti-slip texture on the handles allows for a solid grip.
This radio transmitter acts as a USB Joystick when connected to a personal computer. So you could use it to play FPV simulators like EREADRONE.
Specifications
Frequency Range: 2.4GHz (2403MHz-2447MHz)
2.4G System: NRF24L01 or CC2500
Channel: 8
Support Protocol: Bayang / Futaba S-FHSS / Frsky D16 FCC/ Frsky D16 LBT/ Frsky D8
Power: ≤100mw
Adapted Drone Type: Multirotor
Support USB Charging / Firmware Update
Support BETAFPV Simulator Connected / Customized LiteRadio System / Joystick Calibration
LED Light: Green-Power On / Red-Warning / Blue-Normal
Battery: Built-in 1000mAh 1S Battery
Charging Connector: Type-C
Includes
1x BetaFPV LiteRadio 2 SE RC Transmitter 2.4GHz - FRSKY D8/D16
The LiteRadio 3 Pro Radio Transmitter is an open-source radio remote control that supports the EdgeTX system. It comes with the hall gimbals, featuring four precision bearings, adjustable spring tension, and ergonomic stick ends for an unparalleled feel. The OLED display screen on the top of the transmitter brings visually instant data and a controlling interface to users. What's more, an alternative external nano TX module make it a multi-protocol transmitter.
Check out our RC Transmitters and all our BetaFPV products!
Features
Hall gimbals features four precision bearings, adjustable spring tension, and ergonomic stick ends for an unparalleled feel.
Built-in 2000mAh 1S battery, LiteRadio 3 Pro can work up to 15 hours without an external module, bringing an excellent endurance performance.
A 1.3-inch OLED display screen is newly installed. Controlled by two 5D buttons and settings are easy to be adjusted directly from the display screen.
There is also a nano bay for an external TX module, it supports many popular modules in the market and meets all the protocols such as MULTI, CRSF, PPM, XJT, DSM2, R9M, etc.
Specifications
Channels: 8
Gimbals: Hall Sensor
Frequency Range: 2.4GHz
Antenna: Internal Antenna
RF Output Power: 50mW, 100mW, 250mW (ELRS 2.4G) / 100mW CC2500
Screen: 1.3 inch OLED display screen
Protocol: ExpressLRS 2.4G or CC2500
Battery: Built-in 2000mAh 1S Battery
Operating system: EdgeTX
Port: Type-C USB 3.0 port / 3.5mm Audio port
USB Support: Most Practice Simulator / USB charging / Firmware update / Passthrough (ELRS 2.4G)
Includes
1x BetaFPV LiteRadio 3 Pro RC Transmitter
1x User Manual
2x Joystick Protective Covers
